Search Results

Search found 2704 results on 109 pages for 'miguel ping'.

Page 69/109 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

• Can Remote Desktop be set up to use IPv6?

  - by Garrett

  I have both a Windows 7 Ultimate and a Windows XP Professional machine set up on my home network. I would like to be able to access them from school. Port forwarding is not currently an option (long story). Is there a way to set it so that I can RDP (yes it has to be RDP not something like TeamViewer or LogMeIn) over IPv6, possibly using Teredo? I have tried but I can't seem to get it working. Also I cannot ping these machines' IPv6 addresses. How can I get this set up?

  Read the article

• Juniper J4350 out of order

  - by Benjamin Baron

  I have got two (2) Juniper routers J4350 that are out of order : All the interfaces are down (leds on the interfaces don't ligthen, ping dosen't respond) No output on the console port (even when booting) I've tried to reset the router (holding the RESET CONFIG button on the front panel during 15 seconds) and nothing happened, even while booting the device I've opened the router to check the fans. I've removed some dust and nothing has changed. I wanted to precise that the leds on the front panel are all on: The POWER led is green The STATUS led is red The ALARM led is on and is orange The HA (High Availablity) is on and orange as well I have found nothing on the Internet to solve this problem... Thank you for helping me :)

  Read the article

• Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

  - by Abdul Majeed

  I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

  Read the article

• My computer is listed twice in the Network view; network shares are not accessible

  - by romkyns

  I have a couple of network shares set up on my Win7 machine. They've been in constant use, from that same machine on which they're set up. One morning they just randomly stopped working: When I went looking for what was wrong, I noticed that I also had my PC listed twice in the Network view in Explorer: "Sirius" is the name of the PC on which these screenshots were taken. I may have installed some windows updates around the time this happened. I have since tried rebooting and installing all the latest updates, to no avail. I've also removed the share in question and re-added it, making sure I give all rights to everyone. I'm an administrator on this machine, but I can't access the administrative shares (\\SIRIUS\c$) either, with the same message. I can access \\localhost\AcronisImages and \\localhost\c$, and I can ping sirius. Any ideas?

  Read the article

• Why can't I access a particular website even though the server appears to be available

  - by 50ndr33

  I can't access http://www.lynda.com/ with any of my browsers on my home network. By checking http://www.downforeveryoneorjustme.com/, I can see that the server is up and I can access it via a proxy like TOR. This screen appears immediately after I type the page in It doesn't even try to load the page, it seems. Though when I ping the server I get this: I tried to do ipconfig /flushdns. But it didn't help either. Anyone know how to fix this?

  Read the article

• Plesk 10 port 8443 connection timeout

  - by GriffinHeart

  I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

  Read the article

• What are the things to look out for when adding other domain user to your IIS?

  - by Jack

  I have a Windows Server 2008 R2 called Jack11 that joined a domain called Watson.org. It has IIS 7 installed. From my understanding, we need to add the following into the web.config file <system.web> <identity impersonate="true" /> </system.web> Also, we need to ensure that the server Jack11 can ping to the domain Watson.org. What other setting do we need to setup in order for a user of domain Watson.org (e.g. the user Watson\User1 to access the application in the Server IIS? This is because currently, there is a problem as follows: Exception Details: System.Data.SqlClient.SqlException: Login failed for user 'WATSON\User1'. The error message was displayed when the user User1 wish to access one of the web application in server Jack11 IIS and that web application also do some retrieval of records from the database, which is installed in SQL Server 2008 Enterprise located in the same server Jack11.

  Read the article

• EC2 server in VPC stops responding joining domain

  - by Geoff

  We have a EC2 Windows Server set up and running in our VPC, connected to our network via a Juniper 5GT. This is working well, with the tunnel up and stable. If I then join the server to our local domain, it appears to work - I can then log on using domain credentials, and use domain accounts when applying security to folders etc. After I log out, if I give it around an hour, the box becomes unresponsive. I can't ping it, although a tracert goes all the way barring the last hop - so the tunnel is ok. I can't RDP into it. If I reboot it, then it works for a while before doing the same thing. Un-joining it from the domain fixes the problem, and it stays up and stable. The event logs don't show anything obvious, at least to me. Any ideas?

  Read the article

• Unable to connect to another computer from the Task Scheduler on Windows 7

  - by Clem

  I am getting the following error when trying to connect to another computer from the Task Scheduler on Windows 7: "The remote computer was not found." The computer that I am trying to connect to is definitely on the network as I can ping it and browse its shared folders in Windows Explorer. Note that I get the same error message when trying to perform the same operation from Performance Monitor. This suggests that I need to something to enable remote connection to the Task Scheduler. I am not very experienced with Windows administration and I am not sure where to look. To give a bit more context, I want to use the Task Scheduler to automatically start Perf Mon on a few machines at my company. I'd like to setup the Task Scheduler remotely. Does anyone know what I need to do?

  Read the article

• Remote location looses connectivity

  - by user24559

  I have a remote location that has constant internet access using DSL. The remote location only has three Linksys cameras that use the internet access with a router. There is no computer on the network. The router is configured to use the DYN.org service to keep the IP address updated if the internet provider assigns a new ip address. The problem I am having is the router after a period of time stops responding to incoming ping requests and the cameras are shown offline. However, if I keep one of the cameras constantly streaming data then the connection to all the cameras works just fine all the time. How can I keep the router from appearing to be sleeping and not responding to incoming requests? The router is the Linksys WRT300N.

  Read the article

• Disable IPv6 on Loopback address (Localhost, Computer name, ...)

  - by Greg Bray

  We tried installing a 3rd party software product on a new Windows 2008 R2 server and found that everything works except for accessing local services through loopback addresses such as localhost or the computer name (ex: VPS-Web which resolves to localhost). We are not using IPv6 and would like to disable it until the software is compatible. I tried using these instructions for disabling IPv6 on Windows 2008 R2 but it did not disable the protocol for localhost. Pinging localhost or VPS-Web will still return ::1: instead of 127.0.0.1. I can use ping localhost -4 to get the correct address, but IPv6 takes precedent over IPv4 so the 3rd party software only gets the IPv6 address.

  Read the article

• Setting up a SQL server outside the domain

  - by user12391

  Hi, im very new to this. I've set up an account "SQLBOX" thats on the a network, but not connected to the domain. I have installed an instance of SQL Server 2008 and am trying to connect to it from another machine on the network but am getting "Cannot connect to "SQLBOX"". From the "SQLBOX" i can connect to sqlservers on the domain, but not vice-versa. Any help would be greatly appreciated. Sorry if the description isn't great. EDIT I can ping the box from a machine on the domain

  Read the article

• Linksys WRT54GS V6 Router Blinking Power Light

  - by Frank

  I have a Linksys WRT54GS V6 Router in my possession got it at my local goodwill for 5$. Upon start up the Power LED starts flashing like crazy and at the same time the Ethernet ports all light up once then turn off (DMZ and WLAN never turn on). I can ping the router only by setting a static IP on my Pc. I can also successfully push a file (official Linksys OS and DD-wrt) into it via TFTP but this currently does nothing (no 192.1681.1 Access). Any ideas as to what may be wrong? I think its pretty obvious that it's bricked but.. I keep hearing a whole lot of "if it pings it's fixable" on the internet.

  Read the article

• Public DNS Server fails on Windows Amazon EC2

  - by Adroidist

  I have started a new Windows server instance on Amazon EC2. The security group has the following rules: Ports Protocol Source 22 tcp 0.0.0.0/0 80 tcp 0.0.0.0/0 443 tcp 0.0.0.0/0 3389 tcp 0.0.0.0/0 53 udp 0.0.0.0/0 -1 icmp 0.0.0.0/0 I am able to ping the public DNS server of the machine and i can connect to it using Windows Remote Desktop connection. However, when i put in my web browser the public DNS server, it fails to connect. Morever, I used filezilla and putty (and in both I loaded the private key .pem) but i receive connection timed out. I disabled the firewall on both my pc and the instance (which I entered using Remote desktop connection). Can you please tell me what I am missing?

  Read the article

• OpenVPN and PPTP on XEN VPS

  - by amiv

  I have Debian based system (Ubuntu 11.10) on XEN VPS. I've installed OpenVPN and works great. I need to install PPTP too, so did it and clients can connect, but they have no internet on client side. If I connect to VPN over PPTP I can ping and access to only my VPS by its IP, but ony that. There's no "internet" on client side. It looks it's not DNS problems (I'm using 8.8.8.8) because I can't ping known IPs. I bet the solution is simple, but don't have any idea. Any guess? /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip 46.38.xx.xx remoteip 10.1.0.1-10 /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 proxyarp nodefaultroute lock nobsdcomp /etc/ppp/ip-up [...] ifconfig ppp0 mtu 1400 /etc/sysctl.conf [...] net.ipv4.ip_forward=1 Command which I run: iptables -t nat -A POSTROUTING -j SNAT --to-source 46.38.xx.xx (IP of my VPS) The client can connect, first one gets IP 10.1.0.1 and DNS from Google. I bet it's iptables problem, am I right? I'm iptables noob and I don't have idea what's wrong. And here's the ifconfig and route command before client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22671 errors:0 dropped:81 overruns:0 frame:0 TX packets:2266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1813358 (1.8 MB) TX bytes:667626 (667.6 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:100 errors:0 dropped:0 overruns:0 frame:0 TX packets:100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10778 (10.7 KB) TX bytes:10778 (10.7 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And here's the ifconfig and route command after client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.1.0.1 * 255.255.255.255 UH 0 0 0 ppp0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22989 errors:0 dropped:82 overruns:0 frame:0 TX packets:2352 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1841310 (1.8 MB) TX bytes:678456 (678.4 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12102 (12.1 KB) TX bytes:12102 (12.1 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:46.38.xx.xx P-t-P:10.1.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:66 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:10028 (10.0 KB) TX bytes:660 (660.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And ugly iptables --list output: root@vps3780:~# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- 10.1.0.0/24 anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.1.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable And ugly iptables -t nat -L output: root@vps3780:~# iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- 10.1.0.0/24 anywhere SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere SNAT all -- anywhere anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere As I said - OpenVPN works very good. 10.8.0.0/24 for OpenVPN (on tun0). PPTP won't work. 10.1.0.0/24 for PPTP (on ppp0). Clients can connect, but they haven't "internet". Any suggestions will be appreciated. Second whole day fighting with no results. EDIT: iptables -t filter -F - it resolved my problem :-)

  Read the article

• Plesk 10 port 8443 connection timeout

  - by GriffinHeart

  I've installed plesk 10 on centOS and after installing to access the cp you need to go https::8443 I'm not being able to, and would like to find out why i can ssh to the server and i can, from the server telnet, to those ports. from another machine i can ping it but when i try to telnet or go to that address i get connection timeout, happens with port 80 and 8443 from my netstat netstat -nlp | grep 8443 tcp 0 0 :::8443 :::* LISTEN 25205/sw-cp-serverd How do i find out whats causing the problem? I also have a router but firewall is at the minimum and the server configured as DMZ, also tried to redirect 8443 to 8443 of the server.

  Read the article

• IP addresses not updating, but showing correctly in the DHCP Address Leases

  - by Bobby

  I first noticed this when I tried a RDP to wxp-38-shop and it connected me to the computer wxp-alvinm As you can see in the picture I pinged wxp-38-shop and it shows a different IP then whats given in the Address Leases page (w2k3 server). I tried to do ipconfig /flushdns on the server as well as the client computer, but it didn't update that way. If I do an ipconfig on wxp-38-shop is also shows 192.168.0.153, so why when I ping it from any other computer why would it be showing the wrong IP?

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• Debian Linux server hangs after a week or so

  - by Alex Flo

  I have 2 Debian Linux 6.0.4 servers that have a strange behaviour: after 5-7-10 days they hang. By this I mean the servers need to be restarted and before that ping won't answer. I've been struggling with this problem for a couple of months now and here's some thoughts/what I tried without being able to solve the problem. I changed the RAM on a server. Being 2 different servers I doubt that it could be something related to hardware as a 3rd identical server won't have this problem. I logged the server load and when it crashes the load is fine (quite low) I cannot find anything in the server logs, logs are fine till the server freezes. I don't have access to console unfortunately. While I have years of admin experience I have never encountered such an issue and right now I have no idea where else to investigate. If you have an idea of what I could try in order to fix the problem please share it with me:-)

  Read the article

• Connected to internet but can't browse after trying to remove Covenant Eyes

  - by Joanna

  I recently got a MacBook Pro. It connects to ethernet\wifi and has internet but when I open Safari or Firefox, nothing happens. I get a timeout for all websites. I had Covenant Eyes on my Mac before and tried to remove it. My friends who work with computers have tried everything (ping, nslookup etc). Network diagnostics show no problems I can see I'm connected through ifconfig because I get an IP. I also get a response pinging www.google.gr. There are no proxies set in my Network preferences. Any ideas?

  Read the article

• What can cause peaks in pagetables in /proc/meminfo ?

  - by Fuzzy76

  I have a gameserver running Debian Lenny on a VPS host. Even when experiencing a fairly low load, the players start experiencing major lag (ping times rise from 50 ms to 150-500 ms) in bursts of 3 - 10 seconds. I have installed Munin server monitoring, but when looking at the graphs it looks like the server has plenty of CPU, RAM and bandwidth available. The only weird thing I noticed is some peaks in the memory graph attributed to "page_tables" which maps to PageTables in /proc/meminfo but I can't find any good information on what this might mean. Any ideas what might be causing this? If you need any more graps, just let me know. The interrupts/second count is at roughly 400-600 during this period (nearly all from eth0). The drop in committed was caused by me trying to lower the allocated memory for the server from 512MB to 256MB, but that didn't seem to help.

  Read the article

• belkin wireless router connection drops for ~60sec every ~15 mins

  - by j j

  Hi, I have a belkin wireless-g router, model F5D7230-4. about every 10-15 minutes, for about 1-1.5 mins I won't be able to browse any web sites. during this period, I usually get replys from "ping google.com". maybe 4/5 times I'll get a reply, 1/5 times i don't. I have changed the router DNS entries from "get DNS server from ISP" to 8.8.8.8, google's DNS and that hasn't fixed the situation. This happens on several computers, running windows7, xp, ubuntu, and a mac, so it is definitely NOT an issue with a computer configuration. any ideas?

  Read the article

• Accessing SQL with the PC name not the IP

  - by Cornelius

  I'm trying to connect to a SQL instance (default instance) on a machine. When using the IP of the machine it connects to the machine. Using the name of the machine on that machine you are able to establish a connection to the SQL instance but using the machine name on another PC the connection cannot be established. And gives the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. ... (Microsoft Server, Error: 10060) The machine that I am trying to establish the connection from can ping the machine with the SQL instance both on the IP and on the name. Why would this be and how can I fix it? Edit: pinging the name does resolve the correct IP. Pinging the FQDN also works correctly.

  Read the article

• zeroconf (bonjour/avahi): macs do not see linuxes and vice versa

  - by codesnik

  In my home network I have several OS X boxes and several Ubuntu boxes. each Ubuntu box sees other boxes via zeroconf. I can "ssh ubuntu1.local" and "ping ubuntu1.local" from "ubuntu2.local", but both fail to lookup OSX boxes. and other way around, I can "ssh mini1.local" from "mbair.local". but it doesn't see "ubuntu1.local" why? do ubuntu and osx use different flavours of zeroconf? could be ubuntu, or osx tweaked to use common flavour?

  Read the article

• How much the distance and ms can affect on the download speed ?

  - by Prix

  Let's consider A (client) and B (server) where A makes download from B. How much can a bad routing from A to B affect the download speed ? For example A does a tracert to B and get a response of 10 steps where the avg ms is around 300 with 10% packet loss at the 4 step and when the connection is normal the avg from A to B is 10 ~ 30 ms. Could this sort of impact reduce A download speed drasticaly or as long as both side and routes have enough link for the full speed of A from B and vice-versa it should maintain the same speed ? Besides tracert and the ping analyse of A to B what else is used to identify the problem ? If you need extra information please let me know.

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >