Search Results

Search found 2400 results on 96 pages for 'some noob student'.

Page 69/96 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

• Servers in DMZ will not communicate with each other

  - by Tukaro

  (Full disclosure: I rate barely above "noob" when it comes to networking.) My workplace recent got a new web server. Since we're nearing the end of an overhaul of our website, we're doing a slooooow migration between the old web server and the new one. The old webserver (we'll call it SERVOLD) is Windows Server 2008 with IIS 7. It does not have SQL Server installed. The new server (SERVNEW) is Windows Server 2008 R2, IIS 7.5, with the same version of SQL Server installed. Both are located in the DMZ for our network, and both have their own outward-facing IP address (.3 and .4, respectively). Each server can communicate fine with computers within the domain (not in the DMZ), and those same computers have no trouble communicating with either server. Both servers are also accessible from the internet just fine. However, no matter what, these two servers just refuse to recognize each other. They have the same Workgroup name listed (WORKGROUP), and I thought that would be enough for them to recognize each other. What needs to happen such that I can get these two servers to communicate with each other? We want to do a gradual roll-over to the new website (new one uses ASP.NET, old one uses CFMX), so being able to use one database between both servers is a necessity. Thanks!

  Read the article

• How to configure SCSI hard drives and RAID for Poweredge 2850 web server

  - by Saul

  I'm trying to set up a Poweredge 2850 as a web server, but as a server novice it's causing me some confusion. Its a virgin install so no data to be lost as yet, so I'd like to get the best arrangement for setting up Windows Server 2008. The box will run IIS, a mail and FTP server. The current physical arrangement of the hot swap drives is 1 73GB 3 146GB 5 blank 0 73GB 2 146GB 4 146GB (but flashes green, amber off) When I enter the PERC config screens on boot up I've got Raid Ch- 0 ID 0 ONLIN A00-00 1 ONLIN A00-01 2 ONLIN A01-00 3 ONLIN A01-01 4 HOTSP I think that drives 0 and 1 are set to RAID 1 and drives 2 and 3 are also set to RAID 1, certainly I can see 2 logical drives, both raid 1 of 69880MB and 139900MB Now what I think I am getting here is that the 2 73GB drives mirror each other and the 2 146GB drives mirror 2? so by my noob thinking if a drive fails I can pull it, insert and new one and it will reduplicate from its matching pair? I think the flashing amber probably indicates a failing drive in slot 4, should that just be binned? What confuses me coming from a home user XP background is that when I load up Windows Server 2008 OS under my computer I only see a C drive of about 70GB capacity. i.e wheres the 146GB drive? Any advice appreciated

  Read the article

• How can I parse/ transform text log data before it gets captured in SCOM 2007 R2?

  - by Abs

  I'm pretty much a noob with System Center Operations Manager 2007, and I'm probably missing something pretty basic, but I'm stumped anyway. We're setting up monitoring on some of our servers, and we'd like to capture data from some plain text log files (e.g. DNS debug logs, DHCP logs). It looks to me like I can set up a generic text file monitoring rule and get events captured into the main Ops Manager database, but my understanding is that the whole line of text from the plain text log gets captured as one field. In an ideal world, we'd be able to parse or transform that log file data to make it easier to query later. Is this possible? Is it easy? Do I have to buy expensive 3rd-party software to do it? One more thing: it would be even better if there was a way to stuff this data into the Audit Collection Services (ACS) database instead of the main one, but I'll take what I can get. Any help would be greatly appreciated.

  Read the article

• What are the attack vectors for passwords sent over http?

  - by KevinM

  I am trying to convince a customer to pay for SSL for a web site that requires login. I want to make sure I correctly understand the major scenarios in which someone can see the passwords that are being sent. My understanding is that at any of the hops along the way can use a packet analyzer to view what is being sent. This seems to require that any hacker (or their malware/botnet) be on the same subnet as any of the hops the packet takes to arrive at its destination. Is that right? Assuming some flavor of this subnet requirement holds true, do I need to worry about all the hops or just the first one? The first one I can obviously worry about if they're on a public Wifi network since anyone could be listening in. Should I be worried about what's going on in subnets that packets will travel across outside this? I don't know a ton about network traffic, but I would assume it's flowing through data centers of major carriers and there's not a lot of juicy attack vectors there, but please correct me if I am wrong. Are there other vectors to be worried about outside of someone listening with a packet analyzer? I am a networking and security noob, so please feel free to set me straight if I am using the wrong terminology in any of this.

  Read the article

• Setting up Red Hat Enterprise Linux Server as a mail exchange server

  - by Syedur

  I am a Unix/Linux/Windows Server noob. So, keep that in mind before you throw your stones at my glass house. :P I have a Windows Server 2008 R2 machine that's acting as domain controller, Server A. It's also running a DNS server. I have a Red Hat Enterprise Linux Server 5.3, Server B that is intended for mail server. In order for the mail delivery to happen, I understand that I have to set an MX record on Server A and point it to Server B. Well, I did. I manually added a host name on Server A and pointed to Server B's IP address. Then I added an MX record and pointed it to the host name. That didn't do the trick. After taking the above steps, I used the "dig" command on Server B to lookup the MX record coming back from Server A and it wasn't what I was expecting. What am I doing wrong here? I have noticed that... my Windows machines that are joined to the domain (Server A) are listed under the host names. The machines that are not joined to the domain are not list. This is fine, I am not worried about this. What does concern me, do I have to join the Server B to domain in order for Server A to recognize as a valid host and forward the MX properly? If so, some simple steps on how to join Server B to the domain would also help.

  Read the article

• Subdomains and address bar

  - by Priednis

  I have a fairly noob question about how subdomains work. As I understand at first the DNS server specifies that a request for certain subdomain.domain.com has to go to the IP address of domain.com, and the webserver at domain.com further processes the request and displays the needed subdomain page. It is not entirely clear to me how (for example Apache) server does it. As I understand there can be entries in vhosts.conf file which specify folders that contain the subdomain data. Something like: <VirtualHost *> ServerName www.domain.com DocumentRoot /home/httpd/htdocs/ </VirtualHost> <VirtualHost *> ServerName subdomain.domain.com DocumentRoot /home/httpd/htdocs/subdomain/ </VirtualHost> and there also can be redirect entries in .htaccess files like rewritecond %{http_host} ^subdomain.domain.com [nc] rewriterule ^(.*)$ http://www.domain.com/subdomain/ [r=301,nc] however in this case the user gets directed to the directory which contains the subdomain data but the user gets "out" of the subdomain. I would like to know - how, when going to subdomain.domain.com the subdomain.domain.com, beginning of address remains visible in the address bar of the explorer? Can it be done by an alternate entry in .htaccess file? If a VirtualHost entry is specified in the vhosts.conf file, does it mean, that a new user account has to be specified for access to this directory?

  Read the article

• ESX 4.0 space: DASD, NAS, or ?

  - by thormj

  I put together an ESX box for better management, but its performance is a WTF item; I'm a noob at dealing with ESX, so I'm looking for a laundry-list of reading material to help me straighten this out so I can go back to .NET programming. Current storage system: We're running Raid5+Hotspare (8x500 GB spindles) on a PERC6i on a Dell 2910. Due to ESX limitatios, the PERC is showing the storage as 1x2TB + 1x800GB "partitions." I'm not sure of the setup's configuration (stride / stripe / ???) at all. Our Applications We have a SBS server as well as a minor (2x50 GB, but growing at 10GB/month) database server... Our application that lives on the database VM is CPU and I/O insense; it's a database churning excercise mixed in with a lot of computation on the data (fixing that performance is what I'm supposed to be working on)... Perfomance Issue When I do a backup, restore, or worse (copy a backup from 1 vm to another to move it to the QA VM), the entire system slows to a crawl (even "unrelated" VMs). I originally thought a DASD situation would be quite good since you had PCI-x bandwidth, but the systemwide slowdown is killing productivity. Questions What should I do to make an intelligent decision about NAS vs RAID vs SAN vs DASD? Are there sweet spots/ugly spots in the storage setup? Can you use a SSD PCI-X card in ESX for the tempdb? Good/Bad idea? Is there any way to "share" some image in a copy-on-write fashion? Most of the "Backup-Copy-Restore" is to "put a clean image on the dev boxes"; if I could have them "share" the master image, the "big copy" (2x50 GB) would only need to be done once per week instead of once per dev per week...[runtime performance isn't a concern with the dev boxes, but the backup/copy/restore kills production, SBS, and everything else on the box]

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing problem

  - by Ernest Mueller

  Hey all, I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• Error creating ODBC connection to SQL Server 2008 Express

  - by DavidB

  When creating a System DSN, I get the error: Connection failed: SQLState: '08001' SQL Server Error: 2 [Microsoft][SQL Server Native Client 10.0]Named Pipes Provider: Could not open a connection to SQL Server [2]. Connection failed: SQLState: 'HYT00' SQL Server Error: 0 [Microsoft][SQL Server Native Client 10.0]Login timeout expired I'm running Vista Home Premium 64-bit SP2, and installed SQL Server 2008 Express Advanced without errors. I'll be using the database locally for an app installed on the same PC. I'm able to successfully connect with SQL Server Management Studio using Windows Authentication (my Windows account is a member of local Administrators), and I can successfully create a database with default ownership (defaults to my Windows account). SQL Server Configuration Manager shows that Shared Memory, TCP/IP, and Named Pipes are enabled for SQL Native Client 10.0 Configuration, SQL Native Client 10.0 Configuration (32bit), and SQL Server Network Configuration (SQLEXPRESS). The SQL Server (SQLEXPRESS) and SQL Server Reporting Services (SQLEXPRESS) services are running. When I create a system DSN, my driver choices are SQL server (sqlsrv32.dll 4-10-09), which gives a generic wizard, and SQL Server Native Client 10.0 (sqlncli10.dll 7-10-08), which gives the SQL Server 2008 wizard. I choose the latter. I enter name, description, and have tried both MyPCName and 127.0.0.1 for the server name (browsing turns up nothing). After clicking Next, I leave it at Integrated Windows authentication, and leave Connect to server for additional options checked. After clicking Next, I get the error above. I know it's probably a simple answer, (permission issue?) and I'm a SQL noob, so I appreciate anything that would point me in the right direction. Thanks!

  Read the article

• Single computer on network cannot connect to internet.

  - by user34630

  Hi All, I hope you can help me out! :) I have 3 computers and one device (Xbox) on my home network; 2 running XP and one on Vista. The computer that can't connect to the internet (XP) is old and failing, and shows no warning before it completely runs out of battery. Thus today, I started it up forgetting that I had unplugged it the night before, and it just ran out of battery entirely whilst I was using it and died. I think that before this I had been browsing the internet, but I can't remember for certain. (i.e. The problem I am having may or may not have been caused by this 'hard' power off). Anyway, now when I start the computer up it takes 5-10 minutes after logging on to display the start bar and icons. Also, I cannot browse the internet. The computer seems to connect to the network OK (I have tried both wired and wireless), but I can't visit sites and can't ping web addresses. Pinging the router fails, as does pinging another of my computers on the network. I have never encountered something like this before, and whilst I am no noob I am also not a sysadmin, haha. :( Any help is greatly appreciated, thank you for your time. P.S. I have tried a system restore (newbie move?).

  Read the article

• Bluescreen Stop 0x00000027 RDR_FILE_SYSTEM after cloning system on new HDD

  - by Daniel

  A couple of months ago I got a new 500GB HDD for my no-name-brand Laptop PC and I cloned the complete Win 7 Pro 32bit system with clonezilla from the old 70GB drive to the new one. At first everything was great, the new driver was immediately updated. But since then I get on a more and more frequent level (used to be every 2-3 days, but now it's more like 2-3 times a day) a BSOD Stop error. From the eventlog in Windows I know that there are two different error codes sppoking aroung: 0x00000027 (0xbaad0073, 0x9954f80c, 0x9954f3f0, 0x8ecd7c82) RDR_FILE_SYSTEM 0x00000044 (0x85443230, 0x00000eae, 0x00000000, 0x00000000) MULTIPLE_IRP_COMPLETE_REQUESTS I checked for viruses and did a complete HDD check using the Windows tool and WesternDigital tool (which is the producer of the new HDD) without results. I also looked for driver updates but couldn't find any. The name of the HDD as shown in the device manager is: WDC WD5000BPVT-00HXZT1 ATA Device. I'm really a noob regarding those kind of problems, so if you have any idea what I can try without losing all my data, let me know. Also, if any additional information are required.

  Read the article

• What is a good WordPress theme for long Objective-C code samples [closed]

  - by willc2

  As some of you iPhone developers know, Objective-C can be a verbose language. Long, descriptive variable and method names are the norm. I'm not complaining, it makes code easier to read and code completion makes it easy to type. But damn! Check out this method name for getting a cell in a table view: -(UITableViewCell *)tableView:(UITableView *)tableView cellForRowAtIndexPath:(NSIndexPath *)indexPath; I have a WordPress blog where I publish my code samples as I'm learning the language. One thing I hate on other blogs is how the code won't fit in a column without that scroll bar or without wrapping around. It really made it hard for me to read and comprehend method names back when I was a super-noob (six months ago). Right now I use the clean-looking Fazyvo 1.0 theme by noonnoo. I love the look of it but the columns are just too narrow and it doesn't have support for wider ones. I could hand-modify it but then I'd have to maintain/redo those changes every time I updated it. Instead, I'm looking for a nice theme that has width control built-in and looks good at larger font sizes. Can anyone help? Note: I use WP-CodeBox for code syntax highlighting.

  Read the article

• Connecting jconsole using SOCKS to Amazon EC2

  - by freshfunk

  I'm trying to use jconsole to view stats on an EC2 instance by using a socks proxy created by SSH. I've tried the various scripts mentioned in the links below but to no avail: http://simplygenius.com/2010/08/jconsole-via-socks-ssh-tunnel.html http://gabrielcain.com/blog/2010/11/02/using-ssh-proxying-to-connect-jconsole-to-remote-cassandra-instances/ I'm running ssh -f -ND 8123 myuser@mymachine and verified that at least Firefox goes through it as a proxy. I then run jconsole -J-DsocksProxyHost=localhost -J-DsocksProxyPort=8123 service:jmx:rmi:///jndi/rmi://ec2-XX-XX-XXX-XXX.compute-1.amazonaws.com:8080/jmxrmi I run netstat -n on my EC2 instance and I see a connection created by my machine. However, the connection eventually disappears and I get a 'channel 2: open failed: connect failed: Operation timed out' from my ssh tunnel. I've opened the jmx port through the security group and I've checked the port on the EC2 instance to make sure it's open (by telnet-ing to it). I'm not sure where to look next. Are there some properties in sshd_config or ssh_config I need to enable for tunneling? Or anything in Mac OS X? I feel like a serious noob but sys administration is really not my strong point. I've spent several hours and can't get this to work.

  Read the article

• IPSec Tunnel to Amazon EC2 - Netkey, NAT, and routing issue

  - by Ernest Mueller

  I'm working on getting an IPSec VPN working between Amazon EC2 and my on-premise. The goal is to be able to safely administer stuff, up/download data, etc. over that tunnel. I have gotten the tunnel up in openswan between a Fedora 12 instance with an elastic IP and a Cisco router that's also NATted. I think the ipsec part is OK, but I'm having trouble figuring out how to route traffic that way; there's no "ipsec0" virutal interface because on Amazon you have to use netkey and not KLIPS for the vpn. I hear iptables may be required and I'm an iptables noob. On the left (Amazon), I have a 10. network. Box 1 is privately 10.254.110.A, publically IP 184.73.168.B. Netkey tunnel is up. Box 2 is publically 130.164.26.C, privately 130.164.0.D And my .conf is: conn ni type= tunnel authby= secret left= 10.254.110.A leftid= 184.73.168.B leftnexthop= %defaultroute leftsubnet= 10.254.0.0/32 right= 130.164.26.C rightid= 130.164.0.D rightnexthop= %defaultroute rightsubnet= 130.164.0.0/18 keyexchange= ike pfs= no auto= start keyingtries= 3 disablearrivalcheck=no ikelifetime= 240m auth= esp compress= no keylife= 60m forceencaps= yes esp= 3des-md5 I added a route to box 1 (130.164.0.0/18 via 10.254.110.A dev eth0) but that doesn't do it for predictable reasons, when I traceroute the traffic's still going "around" and not through the vpn. Routing table: 10.254.110.0/23 dev eth0 proto kernel scope link src 10.254.110.A 130.164.0.0/18 via 10.254.110.178 dev eth0 src 10.254.110.A 169.254.0.0/16 dev eth0 scope link metric 1002 Anyone know how to do the routing with a netkey ipsec tunnel where both sides are NATted? Thanks...

  Read the article

• Installing mysqlnd for php 5.4.9 on CentOs 6.3

  - by kira423

  Okay let me get straight to the point, I am a complete noob, and have never done stuff like this at all, I have read tutorial after tuorial but I cant get anything to work. When I tried to install the rpm file I got this error rpm -Uvh ftp://ftp.pbone.net/mirror/rpms.famillecollet.com/enterprise/6/test/x86_64/php-mysqlnd-5.4.9-1.el6.remi.x86_64.rpm Retrieving ftp://ftp.pbone.net/mirror/rpms.famillecollet.com/enterprise/6/test/x86_64/php-mysqlnd-5.4.9-1.el6.remi.x86_64.rpm warning: /var/tmp/rpm-tmp.ez4vvd: Header V3 DSA/SHA1 Signature, key ID 00f97f56: NOKEY error: Failed dependencies: php-pdo(x86-64) = 5.4.9-1.el6.remi is needed by php-mysqlnd-5.4.9-1.el6.remi.x86_64 so I tried installing that rpm file and got this error rpm -ivh ftp://ftp.pbone.net/mirror/rrpms.famillecollet.com/enterprise/6/test/x86_64/php-pdo-5.4.6-1.el6.remi.x86_64.rpm Retrieving ftp://ftp.pbone.net/mirror/rrpms.famillecollet.com/enterprise/6/test/x86_64/php-pdo-5.4.6-1.el6.remi.x86_64.rpm curl: (9) Server denied you to change to the given directory error: skipping ftp://ftp.pbone.net/mirror/rrpms.famillecollet.com/enterprise/6/test/x86_64/php-pdo-5.4.6-1.el6.remi.x86_64.rpm - transfer failed I used the ftp links because I have no idea how else to get them to the server. I think I am getting overly frustrated with this, but I have to get this driver installed for any of my scripts to function correctly. Any help would be greatly appreciated!

  Read the article

• NGINX Configuration Error using Codex Example: Is This a Typo in Codex?

  - by jw60660

  I installed NGINX using this tutorial: C3M Digital NGINX Tuturial but after reading this article on security issues with "cut and paste" configuration tutorials: Neal Poole's article regarding security and NGINX configuration I decided to follow Poole's suggestion to use the configuration suggested in the WordPress codex: Codex on NGINX Configuration I used the Codex configuration for a multisite installation using W3 Total Cache. When attempting to start NGINX I get an error saying that the /etc/nginx/nginx.conf test failed. The error message was: "Restarting nginx: nginx: [emerg] unknown directive "//" in /etc/nginx/sites-enabled/teambrazil.com:18" When I looked at my site specific configuration at that path I noticed the rewrite rule in the server block was: rewrite ^ $scheme://teambrazil.conf$request_uri redirect; That line in the Codex example was: rewrite ^ $scheme://mysite.conf$request_uri redirect; That looked like a mistake to me, and I changed my line to: rewrite ^ $scheme://teambrazil.com$request_uri redirect; I then attempted to restart NGINX but got the same error message. My question is: is that a mistake, and is there anything more I have to do aside from restarting NGINX after making this change. As suggested by both tutorials I set up the directories: /etc/nginx/sites-enabled and /etc/nginx/sites-available and created the appropriate symbolic links using: touch /etc/nginx/sites-available/teambrazil.com ln -s /etc/nginx/sites-available/teambrazil.com /etc/nginx/sites-enabled/teambrazil.com Is there something else I need to consider after making this correction? Or was it not an error in the first place? I'm pretty stuck here. BTW, I am using Debian squeeze as an OS on Amerinoc's VPS. I'm just getting familiar with VPS administration and am pretty much a noob. Thanks very much, would appreciate any input.

  Read the article

• Configure IIS site to work with host header & hosts file entry

  - by HarveySaayman

  I'm I bit of an IIS / Web noob (I'm a C# backend service / winforms dev) so please bare with me :-) I've set up a site in IIS on my local dev machine. In the bindings section of the site ive added 4 bindings, all 4 for http: Host Name Port IP Address blog.sourcecube.co.za 26581 * www.blog.sourcecube.co.za 26581 * blog.sourcecube.co.za 26581 127.0.0.1 www.blog.sourcecube.co.za 26581 127.0.0.1 in my hosts file (drivers\etc\hosts), i've added the folling entries: 127.0.0.1 blog.sourcecube.co.za 127.0.0.1 www.blog.sourcecube.co.za when i ping my domain name from the command line it does in fact resolve to the loopback address, 127.0.0.1. So what I'm expecting to happen when i navigate to blog.sourcecube.co.za in my browser is for it to resolve to 127.0.0.1, and when the request hits IIS, it should know which site to serve because of the host header? But when i navigate to blog.sourcecube.co.za, i get an "Unable to connect, Firefox can't establish a connection to the server at blog.sourcecube.co.za" error. What am I doing wrong? --- UPDATE --- Navigating to blog.sourcecube.co.za:26581 from my browser works... I'd like get it working without specifying the port number though.

  Read the article

• Updating and deleting java (red hat / centos) (new)

  - by JochemTheSchoolKid

  I am a total noob with linux. So please explain clearly if you have a solution for me. I have an VPS and I want to update JAVA. I found a guide on the Java site which says: rpm -e < package_name I searched for the packages: [root@srv1 ~]# rpm -qa | grep java java_cup-0.10k-5.el6.x86_64 java-1.5.0-gcj-1.5.0.0-29.1.el6.x86_64 Than I tried to do the delete command [root@srv1 ~]# rpm -e java-1.5.0-gcj-1.5.0.0-29.1.el6.x86_64 error: Failed dependencies: java-gcj-compat is needed by (installed) java_cup-1:0.10k-5.el6.x86_64 java-gcj-compat >= 1.0.70 is needed by (installed) sinjdoc-0.5-9.1.el6.x86_64 What should I do now? Removing has worked thanks to the answer below Problem two! Now am I installing this package from java [root@srv1 java]# rpm -ivh jre-7u9-linux-i586.rpm Preparing... ########################################### [100%] 1:jre ########################################### [100%] Unpacking JAR files... rt.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/rt.pack jsse.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/jsse.pack charsets.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/charsets.pack localedata.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/ext/localedata.pack plugin.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/plugin.pack javaws.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/javaws.pack deploy.jar... Error: Could not open input file: /usr/java/jre1.7.0_09/lib/deploy.pack Can someone help me again with this?

  Read the article

• How do I install php 5.3 on CentOS?

  - by fivelitresofsoda

  Hi, I have to install php5.3 on my centos server. If i do yum install php, the base repo installs 5.1.6 which is too old for the apps i need to install. So i've been trying to use the ius repository, following the official instructions from ius: root@linuxbox ~]# wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-2.ius.el5.noarch.rpm root@linuxbox ~]# wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm root@linuxbox ~]# rpm -Uvh ius-release*.rpm epel-release*.rpm Ok. Now i simply do yum install php53, etc for all i need... but i get this error: Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Check Error: file /usr/bin/php from install of php53u-cli-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-cli-5.1.6-27.el5_5.3.x86_64 file /usr/bin/php-cgi from install of php53u-cli-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-cli-5.1.6-27.el5_5.3.x86_64 file /usr/share/man/man1/php.1.gz from install of php53u-cli-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-cli-5.1.6-27.el5_5.3.x86_64 file /etc/php.ini from install of php53u-common-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-common-5.1.6-27.el5_5.3.x86_64 Error Summary ------------- I have no idea how to solve this. I think i have to delete the base packages however as a linux noob i don't know how to do that. Please help. Thank you.

  Read the article

• Set up Linux box as WAP for MyBookLive?

  - by AcidFlask

  I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

  Read the article

• Which AMI to to use for Java/Tomcat/MySQL in Amazon EC2?

  - by Justin

  I originally posted this on stackoverflow.com and it was suggested serverfault.com might be a better place to ask this question. So here goes: I'm trying to determine which Amazon Machine Image (AMI) to use as my Virtual Server in Amazon's EC2. For now, I'll need to choose an AMI that complies with the AWS Free Usage Tier. I want to deploy a Java app that I've been developing using Eclipse on Windows XP, Tomcat 7 and MySQL 5.5. I'm aware that I can choose the Basic 32-bit Amazon Linux AMI. Then I'd manually install Tomcat and MySQL (does MySQL get installed on the image or separately on an Elastic Block Store (EBS)?). Here's the rub, I'm a bit of a Linux noob. I can start Tomcat and tail the logs and such on Linux but I'm not familiar with the install process for Tomcat and MySQL on Linux and commands like sudo and chmod. I'm happy to get more hands on with Linux but I'm short on time right now. Are there AMI's that already have Tomcat and MySQL bundled? The Request Instance Wizard shows 805 Community AMI's that are Free Tier Eligible. 51 of the Free Tier Eligible AMI's have "Tomcat" in their name. I'm willing to consider using Elastic Beanstalk but my research thus far hasn't found any discussion of using MySQL with Beanstalk. The discussions all seem to use Amazon's SimpleDB. Any advice is greatly appreciated.

  Read the article

• On Windows machines, what is the typical toolchain for remote maintenance?

  - by Hanno Fietz

  I need to deploy PHP and Python code and the appropriate environment (web server, db server) to remote Windows systems, and I don't know what toolchain would be the equivalent to ssh, scp, bash and the like. So, basically, what I need to be able to do is the following: access remote Windows with the appropriate privileges in a secure manner, like I routinely do with ssh (I don't even know whether that would be a text or graphic interface on Windows). remotely install software: Apache or IIS, MySQL or Postgres, Python or PHP copy files from remote (the application we're deploying) remotely configure the machine to run regular tasks (e. g. checking for updates to the application) automate tasks like downloading files from a designated place The main question is probably how I get onto the machine securely in the first place, and then the rest is general Windows admin knowledge, which probably is too broad a scope to fit into one question. I have years of experience with maintaining Linux boxes and I have used tools of varying sophistication on those, ranging from plain scping of PHP files to deployment of Java application containers and even full VMs with Vagrant. On Windows, I'm a complete noob, and I don't even know where to start. I have installed Apache, MySQL , PHP on a desktop machine maybe twice in my life, that's about it. Bonus points for things that work from a Linux machine at my end, but I could run a VM and do everything from there.

  Read the article

• How can I avoid permission denied errors when attempting to deploy a rails app with capistrano?

  - by joshee

  Total noob here. I'm attempting to deploy an app through Capistrano. I'm getting relentless permission denied errors when I attempt to run cap deploy:update. Seemingly at least some of these errors are due to missing directories that trigger a "Permission Denied" error. (I'm doing setup on root just temporarily.) set :user, 'root' set :domain, 'domainname.com' set :application, 'appname' # adjust if you are using RVM, remove if you are not $:.unshift(File.expand_path('./lib', ENV['rvm_path'])) require "rvm/capistrano" set :rvm_ruby_string, '1.9.2' # file paths set :repository, "ssh://[email protected]/~/git/appname.git" set :deploy_to, "/var/rails/appname" # distribute your applications across servers (the instructions below put them # all on the same server, defined above as 'domain', adjust as necessary) role :app, domain role :web, domain role :db, domain, :primary => true set :deploy_via, :remote_cache set :scm, 'git' set :branch, 'master' set :scm_verbose, true set :use_sudo, false set :rails_env, :production namespace :deploy do desc "cause Passenger to initiate a restart" task :restart do run "touch #{current_path}/tmp/restart.txt" end desc "reload the database with seed data" task :seed do run "cd #{current_path}; rake db:seed RAILS_ENV=#{rails_env}" end end after "deploy:update_code", :bundle_install desc "install the necessary prerequisites" task :bundle_install, :roles => :app do run "cd #{release_path} && bundle install" end Here's my result: ** [domainname.com :: out] Cloning into '/var/rails/appname/shared/cached-copy'... ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied (publickey,gssapi-with-mic,password). ** [domainname.com :: err] fatal: The remote end hung up unexpectedly I'm able to ssh without a password, so not sure about that publickey error. By the way, if I run cap deploy:update without set :deploy_via, :remote_cache, here's my result: ** [domainname.com :: out] Cloning into '/var/rails/appname/releases/20120326204237'... ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied, please try again. ** [domainname.com :: err] Permission denied (publickey,gssapi-with-mic,password). ** [domainname.com :: err] fatal: The remote end hung up unexpectedly command finished Thanks a lot for your help with this.

  Read the article

• nginx hackery : change image file every X request

  - by Vangel

  Let me describe what I am trying to do first. I have a bunch of pictures in a directory called /images/*.(jpg|gif|png|blah blah|) Now say these images are embedded in an html page and I dont really care which image or where its embedded. For every 10th request for the same picture file (if possible) or for any picture I want to display a fixed image (e.g. trollface.jpg). thats it! I have searched around a bit but i am not even sure what I am looking for. Rewrite might help but then its a permanent thing. this has got to do something with requests. I have heard perl scripts can be used with nginx. I can't write an nginx module (though I did bravely lookup the docs and then gave up) Before you ask "But why don't you do it in application, noob?". This is a static files only server. The point is to not execute any binary at all.

  Read the article

• Is It Possible To Self-Teach PHP, Wordpress, CentOS (Linux), Apache, Nginx etc?

  - by Aahan

  consider me a total noob, who uses a Windows PC and has never touched Linux. But I want to administer, manage and take responsibility of my server, at least at some point, if not now. But since I am a full-time blogger I am unable to find time to study at an institute. So, here is my question — - Is It Possible To Self-Teach HTML, CSS, PHP, JavaScript, Wordpress, CentOS (or for that matter any Linux distro), Apache, Nginx, and Varnish? Yes, beginning with HTML, absolutely all of them. I might seem overly ambitious and foolish, but I just want to do it. Aren't there any self-taught server admins? (1) Please help me out with the names of good books, links and whatever you can. (2) How long would it take me to get there (approximately)? 3 years? 5 years? (I have good touch with HTML & Wordpress.) This is a great community, I hope at least some of you will shoot some suggestions at me.

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >