Search Results

Search found 3193 results on 128 pages for 'reboot'.

Page 70/128 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

  • Laptop abruptly powers off after few seconds of booting

    - by Alan Mendelevich
    I have a 3 year old HP Pavilion dv2208 laptop. Recently it started abruptly powering off in like ~20-30 seconds into Windows boot sequence after almost every reboot/shutdown. Even if I leave it in Repair/Start Windows Normally stage it powers off anyway. The only way I managed to workaround this is to enter BIOS setup screen and leave it on for no less than 10 minutes. I don't know what happens there but this helps every time. Any ideas of possible ways to fix this that don't include replacing motherboard are highly appreciated. P.S.: I've tried resetting BIOS to defaults, updating to the latest BIOS version, etc. Happens with both Vista and Windows 7.

    Read the article

  • How to install Windows7 on Hitachi HTS545050a7e380 harddrive?

    - by wurlog
    I have a Samsung NP530U3B with a Hitachi HTS545050a7e380 Harddrive. In the Bios it shows as one drive Hitachi hts545050a7e380 When I try to install Windows 7 it show 2 drives in the setup Drive 0 with 15 GB Drive 1 with 460 GB Guess it is a hybrid of SSD and normal harddrive, right? I tried to install it on the second drive, but after restarting it goes back into the beginning of the Windows 7 installation. The installation routine automatically activated a 100 MB partition on Drive 0. I guess for the bootmanager. Second try: Installation on the 15GB drive. The same. After reboot it wants to install win7 all over again. If I remove the USB Stick I get the message "Missing operation system" Any ideas?

    Read the article

  • Outlook 2010 - Export of an Exchange OST to PST creates files with different sizes each time

    - by Jiri Pik
    This is a most weird issue. I have a couple of exchange OST mailboxes, and just for security, I am exporting them using File / Import / Export to a file / Export to PST file. If I run the export consecutively, it always creates files with different file sizes, WITH NO ERROR OR WARNING that something went wrong. The files should be of the same size as you run it right after the previous backup finished. I found out that if the filesize is substantially lower, then a reboot and back up can fix this up. What's your insight into this problem? What could cause that the files have different sizes and what could have caused that there is no warning? I suspected some Windows Search issue as sometimes the backup fails with a dialog error stating that Windows Search terminated the export.

    Read the article

  • How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

    - by vm370
    as you can see from my question, I have a VLAN configuration problem with a ProCurve3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different VLAN or the Default VLAN. I always get the message "config failed", which is not very helpful. When I try to do it over telnet, the router somehow partially crashes and somehow the utilization on all ports is at 100% and I can barely use the web ui. After a reboot everything is fine again, but the configuration was not changed... The traffic after this partial crash looks like a broadcast storm, however there are definitely no loops in the segment. I also updated to the latest stable firmware, but the problem persists. Thanks a lot in advance Br vm370

    Read the article

  • Cannot terminate proces: access is denied

    - by jao
    Skype and Spotify remain active after I close them. When I try to close them via Task Manager Details End Task, I get the following error: The operation could not be completed. Access is denied. So I have to reboot to get rid of these programs or to log in to Skype again. Also, running a CMD as administrator and executing taskkill /f /im skype.exe results in an Access is denied error. What is going on? (this is Windows 8 RTM x64) update I have to kill skype.exe because it crashed and when I restart skype, I get the following error: It says: Could not open Skype, you are already signed in on this computer. update 2 The process is owned by my own username.

    Read the article

  • vihostupdate, many patches at once

    - by skomak
    Hi, i have ESXi 4.0 installed so i want to install all patch bundles available using vihostupdate.pl script from vm perl sdk. I can install it by typing: vihostupdate.pl -server 192.168.1.177 -b "C:\Documents and Settings\dawids\Pulpit\patche\ESXi-4.0.0-update01.zip" -i then patch 2,3 etc. But I would like to install them all at once, is there such possibility? Maybe there is possible to use vihostupdate patch1 then vihostupdate patch2... and after all patching reboot instead rebooting after 1 patch bundle. How is it working?

    Read the article

  • System-install-packages missing

    - by Kumar P
    i am using RedHat Enterprise Linux 5.1. When i use add-remove software in application menu, i think, that i wrongly uninstalled something. so after reboot that menu item missing. Also i can't use system-install-packages in terminal. When i double click rpm package it open as archive. And i specifically open it as software installer by open with other application, it saying error /usr/bin/system-install-packages missing. Help me to solve this problem ...

    Read the article

  • Jan 2010 Microsoft update trashed my Win XP (64bit) PC

    - by Mark Pawelek
    I waited until this morning to install these 5 updates. My ancient Win XP (32 bit) PC has no problems but my Win XP 64 bit will not start. From the startup menu none of the 5 options given (e.g. safe mode, last known good configuration, etc) work. After selecting an option, the Windows Logo screen appears. About 9 seconds later a blue screen of death flashes [I can't read the error messages because it's there for about 100 ms] then it cycles through the reboot again. PS: This is a pretty cheap mobo (Ge Force) with an AMD 3 GH chip - but until today it did actually work. What should I do? Reinstall the O/S?

    Read the article

  • Need help identiying a nasty rootkit in Windows

    - by goofrider
    I have a nasty rootkit that not tools seem to be able to idenity. I know for sure it's a rootkit, but I can figure out which rootkit it is. Here's what I gathered so far: It creates multiple copies of itself in %HOME%\Local Settings\Temp with names like Q.EXE, IAJARZ.exe, etc., and install them as hidden services. These EXE have SysInternals identifiers in them so they're definitely rootkits. It hooked very deep in the system, including file read/write, security policies, registry read/write, and possibly WinSock/TCP/IP. When going to Sophos.com to download their software, the rootkit inject something called Microsoft Ajax Tootkit into the page, which injects code into the email submission form in order to redirect it. (EDIT: I might have panicked. Looks like Sophos does use an AJAZ email form, their form is just broken on Chrome so it looked like a mail form injection attack, the link is http://www.sophos.com/en-us/products/free-tools/virus-removal-tool/download.aspx ) Super-Antispyware found a lot of spyware cookies, in the name of .kaspersky.2o7.net, etc. (just chedk 2o7.net, looks like it's a legit ad company) I tried comparing DNS lookup from the infected systems and from system in other physical locations, no DNS redirections it seems. I used dd to copy the MBR and compared it with the MBR provided by ms-sys package, no differences so it's not infecting MBR. No antivirus or rootkit scanner be able to identify it. Most of them can't even find it. I tried scanning, in-situ (normal mode), in safe mode, and boot to linux live CD. Scanners used: Avast, Sophos anti rootkit, Kasersky TDSSKiller, GMER, RootkitRevealer, and many others. Kaspersky reported some unsigned system files that ought to be signed (e.g. tcpip.sys), and reported a number of MD5 mismatches. But otherwise couldn't identify anything based on signature. When running Sysinternal RootkitRevealer and Sophos AntiRootkit, CPU usage goes up to 100% and gets stucked. The Rootkit is blocking them. When trying running/installing HiJackThis, RootkitRevealer and some other scanners, it tells me system security policy prevent running/installing it. The list of malicious acitivities go on and on. here's a sample of logs from all my scans. In particular, aswSnx.SYS, apnenfno.sys and PROCMON20.SYS has a huge number of hooks. It's hard to tell if the rootkit replaced legit program files like aswSnx.SYS (from Avast) and PROCMON20.SYS (from Sysinternal Process Monitor). I can't find whether apnenfno.sys is from a legit program. Help to identify it is appreciated. Trend Micro RootkitBuster ------ [HIDDEN_REGISTRY][Hidden Reg Value]: KeyPath : HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\sptd\Cfg Root : 586bfc0 SubKey : Cfg ValueName : g0 Data : 38 23 E8 D0 BF F2 2D 6F ... ValueType : 3 AccessType: 0 FullLength: 61 DataSize : 32 [HOOKED_SERVICE_API]: Service API : ZwCreateMutant Image Path : C:\WINDOWS\System32\Drivers\aswSnx.SYS OriginalHandler : 0x8061758e CurrentHandler : 0xaa66cce8 ServiceNumber : 0x2b ModuleName : aswSnx.SYS SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwCreateThread Image Path : c:\windows\system32\drivers\apnenfno.sys OriginalHandler : 0x805d1038 CurrentHandler : 0xaa5f118c ServiceNumber : 0x35 ModuleName : apnenfno.sys SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwDeleteKey Image Path : C:\WINDOWS\system32\Drivers\PROCMON20.SYS OriginalHandler : 0x80624472 CurrentHandler : 0xa709b0f8 ServiceNumber : 0x3f ModuleName : PROCMON20.SYS SDTType : 0x0 HiJackThis ------ O23 - Service: JWAHQAGZ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\JWAHQAGZ.exe O23 - Service: LHIJ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\LHIJ.exe Kaspersky TDSSKiller ------ 21:05:58.0375 3936 C:\WINDOWS\system32\ati2sgag.exe - copied to quarantine 21:05:59.0217 3936 ATI Smart ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0342 3936 C:\WINDOWS\system32\BUFADPT.SYS - copied to quarantine 21:05:59.0856 3936 BUFADPT ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0965 3936 C:\Program Files\CrashPlan\CrashPlanService.exe - copied to quarantine 21:06:00.0152 3936 CrashPlanService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0246 3936 C:\WINDOWS\system32\epmntdrv.sys - copied to quarantine 21:06:00.0433 3936 epmntdrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0464 3936 C:\WINDOWS\system32\EuGdiDrv.sys - copied to quarantine 21:06:00.0526 3936 EuGdiDrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0604 3936 C:\Program Files\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService.exe - copied to quarantine 21:06:01.0181 3936 FLEXnet Licensing Service ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0321 3936 C:\Program Files\AddinForUNCFAT\UNCFATDMS.exe - copied to quarantine 21:06:01.0430 3936 OTFSDMS ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0492 3936 C:\WINDOWS\system32\DRIVERS\tcpip.sys - copied to quarantine 21:06:01.0539 3936 Tcpip ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0601 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - copied to quarantine 21:06:01.0664 3936 HKLM\SYSTEM\ControlSet003\services\TULPUWOX - will be deleted on reboot 21:06:01.0664 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - will be deleted on reboot 21:06:01.0664 3936 TULPUWOX ( UnsignedFile.Multi.Generic ) - User select action: Delete 21:06:01.0757 3936 C:\WINDOWS\system32\Drivers\usbaapl.sys - copied to quarantine 21:06:01.0866 3936 USBAAPL ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0913 3936 C:\Program Files\VMware\VMware Player\vmware-authd.exe - copied to quarantine 21:06:02.0443 3936 VMAuthdService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - User select action: Skip 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - User select action: Skip

    Read the article

  • EC2 server in VPC stops responding joining domain

    - by Geoff
    We have a EC2 Windows Server set up and running in our VPC, connected to our network via a Juniper 5GT. This is working well, with the tunnel up and stable. If I then join the server to our local domain, it appears to work - I can then log on using domain credentials, and use domain accounts when applying security to folders etc. After I log out, if I give it around an hour, the box becomes unresponsive. I can't ping it, although a tracert goes all the way barring the last hop - so the tunnel is ok. I can't RDP into it. If I reboot it, then it works for a while before doing the same thing. Un-joining it from the domain fixes the problem, and it stays up and stable. The event logs don't show anything obvious, at least to me. Any ideas?

    Read the article

  • Disk boot failure in Windows 7 64-bit after installing the latest NVIDIA drivers

    - by Domchi
    I successfully installed the newest NVIDIA drivers (275.33) in Windows 7 64-bit and rebooted afterwards just in case. After the reboot, I got an error about missing MBR. I disconnected the slave disk so that Windows doesn't get confused and got this message: DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER It seems that Windows doesn't recognize the main disk anymore. I booted from Windows install disk but the main disk doesn't get listed as possible Windows locations to repair, and I can't get to it from the recovery prompt. The BIOS does recognize it, and I'm able to see it if I run diskpart - however "detail disk" in diskpart says that there are no volumes on the disk. I also tried bootrec /FixMbr without effect, and bootrec /FixBoot which gives the error message: Element not found. What else can I do? Why would diskpart say there are no volumes on the disk?

    Read the article

  • Why does Finder keeping showing me menus in Spanish?

    - by Ian C.
    This has happened before. A full reboot fixed it. This time: no go. The bottom of my menus, when I command-click on a file in Finder, are in Spanish. You can see a screen grab here: http://twitpic.com/10c63y How can I stop this from happening? I'm sure I inadvertantly hit a key combination that did this, but I'm stumped as to what that was. My System Preference settings for Language & Text have language set to Canadian English.

    Read the article

  • Cannot find the 2nd datastore after upgrading ESXi 3.5

    - by aXqd
    I have an ESXi server (version 3.5) with about 60 VMs. It has 2 hard disks, each of which is regarded as a datastore. After upgrading through 'VMware Infrastructure Update' tool(still staying with 3.5 instead of 4.0) and a reboot, I can only see the 1st datastore. Hence many VMs are, now, inaccessible. I wonder how I can get the 2nd datastore back. I am sorry, but I did't have the 2nd datastore backuped before. BTW, I am still thinking of upgrading directly to version 4.0 to see if it can fix the driver problem. How about that?

    Read the article

  • Unlock file on Windows Server 2003 by remote desktop without rebooting

    - by BalusC
    We've several Windows Server 2003 machines running, each with its own purposes. There are scheduled jobs which synchronizes some files over SFTP using WinSCP. Very sometimes a newly copied file is left locked in the "inbox" folder without any reason. The machine's own background task (programmed in Java) can't move it to the "processed" folder anymore after processing it. Manually moving it only yields the well known error message Cannot move [filename]: it is being used by another person or program. The only resort is to reboot the machine, but we would of course like to avoid that. Any suggestions? I tried Unlocker which works fine locally at WinXP, but doesn't work at those Win2K3 machines by remote desktop (unlock option doesn't show up in rightclick context menu). I tried Process Explorer as well as described in this blog article, but it caused the server to crash (not sure if that's because it's executed through remote desktop).

    Read the article

  • MacBook Pro screen goes dark

    - by Mike M
    I've had my MacBook Pro for two years now; no problems so far (it has had 3rd party RAM from the get go). Today, I'm copying a particularly large VM from an External disk drive to local MacBook disk. It has about 3GB to go and I take off to do some other things and when I come back my screen is "dark". The computer is still on but I can't see anything. I forced a reboot by holding down the power button, it starts up with the "chimes", but still no screen. I've done this several times. Any ideas? Do you think the hard disk activity caused it to get too hot?

    Read the article

  • wifi routers and concurrent devices

    - by Joelio
    We have a Linksys WRT54G WiFi router in our office which was working great when we had 5-6 folks. Now on peak days we have 10-15 people, each with a computer, smartphone, etc, and an ooma VOIP device. On average 1-2 times a day I need to go hard reboot the router, and sometimes the border router (Cox-supplied device). I assume this is just because the router cant handle this many concurrent users. So my question is can these consumer routers handle this kind of load? If not, would adding more devices solve the problem, and how close proximity can I put 2 routers without having interference problems (our office area is not that big physically)?

    Read the article

  • Why do I have no TTY on a basic Ubuntu 9.10 server install?

    - by pr1001
    I have reinstalled Ubuntu 9.10 Server several times on a bog standard 1RU server and each time I finish the install and reboot I see GRUB run and am then presented with a black screen. The machine is running just fine, as I am able to SSH in, but I can't see anything on the attached monitor. I have a simple LCD screen connected via VGA and a signal is apparently being output to it, as it doesn't go asleep. Looking at /var/log/syslog I see: Mar 24 14:57:44 bridge5 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] However, I later see: Mar 24 14:57:44 bridge5 kernel: [ 0.001368] console [tty0] enabled Any thoughts? Thanks!

    Read the article

  • Why's SMC failing on startup?

    - by Brian Knoblauch
    Trying to remove a user from one of our servers, but I seem to be thwarted at every turn... SMC refuses to load the user list (failing with a NoClassDefFoundError in the listAll method of UserContent). vipw just returns with "vipw: /etc/passwd file busy". I'm the only user on the system at the moment (it's our backup SRSS box), and both of these fail even right after a reboot. I don't have console access at the moment either unfortunately (or I would try single user mode). Of course, even if init mode S worked and let me do this one task, it doesn't solve the root problem. Ideas?

    Read the article

  • Home Server restore fails cannot find boot device

    - by Tim Heuer
    I am using Windows Home Server to backup my PCs. I recently had a hard drive failure on one of my WHS connected PCs and obtained an identical sized/speed drive for my laptop. I used the latest home server restore CD and did the restore. It said it completed successfully. Upon reboot, it says 'cannot find boot device' and lists all my drives (hard drive, cd, network book) indicating no valid operating system was found. I boot using the Win7 repair disk and while it doesn't see the operating system, it sees the drive and if I go into a command prompt, I can see all my data on the drive. My laptop is Windows 7 64-bit Ultimate. I've tried most everything I can think of. I'm a technical user (software developer) so I'm pretty aware of how things work (or should). I don't feel like I'm missing a simple step here.

    Read the article

  • Attempting to install .NET framework 4 *full* installs *client* instead

    - by msorens
    On a Win7 SP1 32-bit machine, I initially had .NET 4 client installed and wanted to upgrade to .NET 4 full. I downloaded the full installer dotNetFx40_Full_x86_x64.exe from Microsoft. After download the file showed 48.11MB, the correct size for the full package (vs. 41MB for the client). I ran the installer and it first prompted to repair or remove the existing package. I chose to remove, so uninstalled the two parts, 4 extended and 4 client. Reboot. I reran the installer and it began installation, showing that it was installing the client. Though this raised an eyebrow for me, I let it run to completion, thinking it might be reporting the full install in sections. But after completion, I again ended up with 4 extended and 4 client installed! Obviously I am missing something; ideas...?

    Read the article

  • Restoring Mac-bootcamp-windows-partition image to Windows machine

    - by jpwagner
    Hi, I'm running Windows XP sp3 on my mac using bootcamp. Objective: I'd like to move this partition to a windows machine. This is what I tried: 1. create image using winclone 2. restore drive to disk partition on windows machine using paragon 3. reboot from new partition Results: it attempts to boot in XP (windows flag and progress bar load screen) but then gives me the old BSOD. safe mode just hangs while loading. (I then uninstalled KB977165 on a hunch, but that did nothing to help the issue.) Any ideas, advice, etc would be greatly appreciated. Thanks!

    Read the article

  • Restoring Mac-bootcamp-windows-partition image to Windows machine

    - by jpwagner
    Hi, I'm running Windows XP sp3 on my mac using bootcamp. Objective: I'd like to move this partition to a windows machine. This is what I tried: 1. create image using winclone 2. restore drive to disk partition on windows machine using paragon 3. reboot from new partition Results: it attempts to boot in XP (windows flag and progress bar load screen) but then gives me the old BSOD. safe mode just hangs while loading. (I then uninstalled KB977165 on a hunch, but that did nothing to help the issue.) Any ideas, advice, etc would be greatly appreciated. Thanks!

    Read the article

  • ASP.NET Session Management - which SQL Server option?

    - by frumious
    We're developing some custom web parts for our WSS 3 intranet, and have just run into something we'd like to use ASP.NET sessions for. This isn't currently enabled on the development server. We'd like to use SQL Server as the storage mechanism, because the production environment is a web farm with very simple load-balancing. There are 3 options you can choose from to set up the SQL Server session storage, tempdb, default separate DB, named DB. Both tempdb and default separate DB create a new DB to store certain information in; tempdb stores the actual session info in tempdb, which doesn't survive a reboot, and default separate DB stores everything in the new DB. Since you've got to create the new DB either way, my question is this: why would you ever choose to store the session info in tempdb? The only thing I can think of is if you'd like to have the ability to wipe the session by rebooting the server, but that seems quite apocalyptic!

    Read the article

  • Windows 7 setup hangs after "Starting Windows..."-screen

    - by Eirik Lillebo
    Hi! I'm having some trouble installing Windows 7. I need to install the OS from boot in order to split my C: into two different partitions, as this is not allowed when installing from inside Vista. When I boot up from the install disc, I get the usual "Windows is copying files..."-screen, shortly followed by the "Starting Windows..."-screen with the animated window-logo or whatever. Then it looks as if the installation is about to begin with a blue screen and a cursor I can move around, but here it all stops. Nothing more happens, and the setup seems to hang. Not a single key on my keyboard has any effect, and all I am left to do is to abort and reboot. I've tried to install using two different DVDs (not clones), and the same thing happens every time. What may be causing this, and how may I fix it? Thanks in advance :)

    Read the article

  • something is downloading in background Linux

    - by wisdom
    My laptop boots normally to Linux -LinuxMint- and immediately I like to open gnome-system-monitor but the shock is that something is downloading(the problem has been out 2 days ago) and nothing I run yet ! I did iftop in terminal but nothing strange -a screen shot provided-, also I tried nethogs which showed nothing at all. The more complicated when I reboot and same problem is there so I can't browse/surf Internet, no one connected to my network can browse any more it's absorbing the stream horribly! After many reboots it will go to normal state(no background downloading). But really I can't figure out the problem going behind the scene ! Any suggestion,any help would be appreciated...thanks

    Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >