Search Results

Search found 53148 results on 2126 pages for 'ubuntu 10 4'.

Page 70/2126 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• setup dhcp server - "Job failed to start"

  - by jdicarreira

  I have an eth0 and eth1, eth0 has dynamic ip and on eth1 i setup static ip: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 10.10.0.1 netmask 255.0.0.0 gateway 10.10.0.1 ` and then i setup the "isc-dhcp-server" with the fowling command: INTERFACES="eth1" Finally... I went to this one "dhcpd.conf", with the fowling comand: default-lease-time 650; max-lease-time 79520; option subnet-mask 255.0.0.0; option broadcast-address 10.10.0.255; option routers 10.10.0.2; subnet 10.10.0.0 netmask 255.0.0.0 { range 10.10.0.10 10.10.0.250; } When I try to "sudo /etc/init.d/isc-dhcp-server start", I get "start: Job failed to start" Anyone knows whats wrong? :/

  Read the article

• Can a 10-bit monitor connection preserve all tones in 8-bit sRGB gradients on a wide-gamut monitor?

  - by hjb981

  This question is about color management and the use of a higher color depth, 10 bits per channel (30 bits in total, resulting in 1.07 billion colors, or 1024 shades of gray, sometimes referred to as "deep color") compared to the standard of 8 bits per channel (24 bits in total, 16.7 million colors, 256 shades of gray, sometimes referred to as "true color"). Do not confuse with "32 bit color", which usually refers to standard 8 bit color with an extra channel ("alpha channel") for transparency (used to achieve effects like semi-transparent windows etc). The following can be assumed to be in place: 1: A wide-gamut monitor that supports 10-bit input. Further, it can be assumed that the monitor has been calibrated to its native gamut and that an ICC color profile has been created. 2: A graphics card that supports 10-bit output (and is connected to the monitor via DisplayPort). 3: Drivers for the graphics card that support 10-bit output. If applications that support 10-bit output and color profiles would be used, I would expect them to display images that were saved using different color spaces correctly. For example, both an sRGB and an adobeRGB image should be displayed correctly. If an sRGB image was saved using 8 bits per channel (almost always the case), then the 10-bit signal path would ensure that no tonal gradients were lost in the conversion from the sRGB of the image to the native color space of the monitor. For example: If the image contains a pixel that is pure red in 8 bits (255,0,0), the corresponding value in 10 bits would be (1023,0,0). However, since the monitor has a larger color space than sRGB, sending the signal (1023,0,0) to the monitor would result in a red that was too saturated. Therefore, according to the ICC color profile, the signal would be transformed into a different value with less red saturation, for example (987,0,0). Since there are still plenty of levels left between 0 and 987, all 256 values (0-255) for red in the sRGB color space of the file could be uniquely mapped to color-corrected 10-bit values in the monitor's native color space. However, if the conversion was done in 8 bits, (255,0,0) would be translated to (246,0,0), and there would now only be 247 available levels for the red channel instead of 256, degrading the displayed image quality. My question is: how does this work on Ubuntu? Let's say that I use Firefox (which is color-aware and uses ICC color profiles). Would I get 10-bit processing, thus preserving all levels of an 8-bit picture? What is the situation like for other applications, especially photo applications like Shotwell, Rawtherapee, Darktable, RawStudio, Photivo etc? Does Ubuntu differ from other operating systems (Linux and others) on this point?

  Read the article

• How to synchronize a whole Ubuntu?

  - by Avio

  I think that the time is ripe to have my whole Ubuntu synchronized just as my Dropbox folder is. Given that we are always talking about files and directories, what's the difference between my Documents folder and my /usr system directory? Almost none, except for their location. In fact, I think that there is just one big issue that prevents people to have their beloved installations mirrored wherever they go: symlinks. Dropbox, Google Drive, Ubuntu One, Sugarsync, Skydrive, none of these services support symlinking. This means that if I push a symlink in one of the synced folders, locally the symlink is kept as is, but remotely (in the cloud or on the other synced machines) the symlink is resolved to the actual file that was originally pointed to. This completely disrupts Linux installations, thus these services can't be used for this purpose. So the question is. Does anybody knows a way to achieve this? A whole Ubuntu, always synchronized with a remote running copy, but still locally stored on both disks? My best guess is that I could use NFS. But the main difference between Dropbox and NFS is that NFS is a remote filesystem that always forces to remotely access the files, while Dropbox pushes modifcations to local filesystems (and thus would perform better). I've also heard about NFS caching. Does anybody knows if this solution could approximate Dropbox in this sense? P.s. I know that /boot, /dev, /proc, /run, /tmp and device-specific mountpoints in /mnt and /media will have to be left out the sync mechanism. What I'm interested in is the principle. Can this be done with reasonable performance, having reasonable resources (e.g. ~ 1Mbps upload bandwidth and a public IP address)?

  Read the article

• Excel Template Teaser

  - by Tim Dexter

  In lieu of some official documentation I'm in the process of putting together some posts on the new 10.1.3.4.1 Excel templates. No more HTML, maskerading as Excel; far more flexibility than Excel Analyzer and no need to write complex XSL templates to create the same output. Multi sheet outputs with macros and embeddable XSL commands are here. Their capabilities are pretty extensive and I have not worked on them for a few years since I helped put them together for EBS FSG users, so Im back on the learning curve. Let me say up front, there is no template builder, its a completely manual process to build them but, the results can be fantastic and provide yet another 'superstar' opportunity for you. The templates can take hierarchical XML data and walk the structure much like an RTF template. They use named cells/ranges and a hidden sheet to provide the rendering engine the hooks to drop the data in. As a taster heres the data and output I worked with on my first effort: <EMPLOYEES> <LIST_G_DEPT> <G_DEPT> <DEPARTMENT_ID>10</DEPARTMENT_ID> <DEPARTMENT_NAME>Administration</DEPARTMENT_NAME> <LIST_G_EMP> <G_EMP> <EMPLOYEE_ID>200</EMPLOYEE_ID> <EMP_NAME>Jennifer Whalen</EMP_NAME> <EMAIL>JWHALEN</EMAIL> <PHONE_NUMBER>515.123.4444</PHONE_NUMBER> <HIRE_DATE>1987-09-17T00:00:00.000-06:00</HIRE_DATE> <SALARY>4400</SALARY> </G_EMP> </LIST_G_EMP> <TOTAL_EMPS>1</TOTAL_EMPS> <TOTAL_SALARY>4400</TOTAL_SALARY> <AVG_SALARY>4400</AVG_SALARY> <MAX_SALARY>4400</MAX_SALARY> <MIN_SALARY>4400</MIN_SALARY> </G_DEPT> ... </LIST_G_DEPT> </EMPLOYEES> Structured XML coming from a data template, check out the data template progression post. I can then generate the following binary XLS file. There are few cool things to notice in this output. DEPARTMENT-EMPLOYEE master detail output. Not easy to do in the Excel analyzer. Date formatting - this is using an Excel function. Remember BIP generates XML dates in the canonical format. I have formatted the other data in the template using native Excel functionality Salary Total - although in the data I have calculated this in the template Conditional formatting - this is handled by Excel based on the incoming data Bursting department data across sheets and using the department name for the sheet name. This alone is worth the wait! there's more, but this is surely enough to whet your appetite. These new templates are already tucked away in EBS R12 under controlled release by the GL team and have now come to the BIEE and standalone releases in the 10.1.3.4.1+ rollup patch. For the rest of you, its going to be a bit of a waiting game for the relevant teams to uptake the latest BIP release. Look out for more soon with some explanation of how they work and how to put them together!

  Read the article

• .net Framework won't install on Server 2003 SP2 x64

  - by Yvan JANSSENS

  Hi, When I install the .net Framework 3.5 SP1 on my rental VPS, I get the message that setup has failed. It's a Server 2003 VPS w/ SP2 installed (64-bit). The .net Framework v 2.0 installed correctly. How do I fix this? This is the installation log: [03/10/10,07:44:46] Microsoft .NET Framework 2.0a x64: [2] Failed to fetch setup file in CBaseComponent::PreInstall() [03/10/10,07:44:47] setup.exe: [2] ISetupComponent::Pre/Post/Install() failed in ISetupManager::InternalInstallManager() with HRESULT -2147467260. [03/10/10,07:44:48] setup.exe: [2] CSetupManager::RunInstallPhase() - Call to Pre/Install/Post for InstallComponents failed [03/10/10,07:44:49] setup.exe: [2] CSetupManager::RunInstallPhaseAndCheckResults() - RunInstallPhase() returned a NULL piActionResults [03/10/10,07:44:49] setup.exe: [2] CSetupManager::RunInstallFromList() - RunInstallPhaseAndCheckResults failed [2] [03/10/10,07:44:51] setup.exe: [2] ISetupManager::RunInstallLists(IP_PREINSTALL failed in ISetupManager::RunInstallFromThread() [03/10/10,07:44:52] setup.exe: [2] ISetupManager::RunInstallFromThread() failed in ISetupManager::RunInstall() [03/10/10,07:44:53] setup.exe: [2] CSetupManager::Run() - Call to RunInstall() failed [03/10/10,07:44:59] WapUI: [2] DepCheck indicates Microsoft .NET Framework 2.0a x64 is not installed. [03/10/10,07:45:00] WapUI: [2] DepCheck indicates XPSEPSC x64 Installer was not attempted to be installed. [03/10/10,07:45:02] WapUI: [2] DepCheck indicates Microsoft .NET Framework 3.0 SP2 x64 was not attempted to be installed. [03/10/10,07:45:02] WapUI: [2] DepCheck indicates Microsoft .NET Framework 3.5 (x64) 'package' was not attempted to be installed. [03/11/10,14:19:23] Microsoft .NET Framework 3.0 SP2 x64: [2] Error: Installation failed for component Microsoft .NET Framework 3.0 SP2 x64. MSI returned error code 1604 [03/11/10,14:26:14] WapUI: [2] DepCheck indicates Microsoft .NET Framework 3.0 SP2 x64 is not installed. Thanks!! Yvan

  Read the article

• Is Ubuntu Touch a separate distribution or the same one?

  - by Nickolai Leschov

  I would like to install the latest Ubuntu Touch on a 2013 Nexus 7 tablet. Which version should I be looking for: the regular Ubuntu (for ARM platform) or a separate Ubuntu Touch? I understand that after Ubuntu Touch is in frantic development, but I would like to be able to keep track which one is which. I can see the following images: Ubuntu 14.09 RTM, daily-preinstalled Ubuntu Touch 14.10 (Utopic Unicorn) Daily Build Ubuntu 14.10 (Utopic Unicorn) Daily Build, but only i386 and amd64; no ARM. Does it mean that ARM variant has moved to one of the first two links?

  Read the article

• Why does Ubuntu 10.10 show blank screen during startup?

  - by user8372

  When I try to login to Ubuntu 10.10 I get a flickering screen for a second showing - Ubuntu 10.10 ............. and then I get a blank purple coloured screen[Ubuntu's theme colour] which doesn't progress any further Can anybody suggest a remedy to this problem? From whatever questions I searched in various Ubuntu Forums it seems like this problem is likely caused by a missing NVIDIA Display Driver[which is being used in my Sony Vaio Laptop] update in Ubuntu releases If that's the case then how can I update my NVIDIA Display Driver for Ubuntu 10.10 without being able to log into the Ubuntu 10.10?

  Read the article

• Ubuntu web server cluster checks Ubuntu repository for script updates with cron

  - by StuartTheY

  I have a cluster of Ubuntu 12.04 web servers running a lamp stack. All of these servers are connected to a Load Balancer on Amazon Web Services. What I want to be able to do is have a dedicated Ubuntu server that I can update the PHP files on and have the other web servers check with cron to get the updates files from the repository. They don't have to use cron but that was the only thing I could think of, unless there was a way to have the updated repository tell them that it has updated files. And then how to transfer those files. Also if there is a ways for a server to check for updated files when it boots because I am going to be using auto scaling on AWS so when there is an increase in the load and another server gets created I need it to download the updated files from the repository when launched. Not sure how to transfer files from server to server.

  Read the article

• ubuntu hardrive repartition without uninstalling ubuntu or windows 7 and losing data of hardrive

  - by user141692

  I have and asus r500v with 750 gb gpt system uefi motherboard core i7 3610qm, nvidia geforce gt, with ubuntu and w7 dual boot, I had problems installing ubuntu because of the grub but I fix it with https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/807801, but I still have the problem of "warning: the partition is misaligned by 3072 bytes. this may result iin very poor performance. Repartitioning is suggested" in every linux partitioin I made and my 750 gb is not being used at the maximun capacity it only uses 698 gb. I want to make partitions so that the warning doesnt show up and I can use the maximum capacity of the HDD, as I did with another dual boot laptop (compaq presario cq40). I have the following partitions: unknown 1.0Mb: partition type: lynux Basic DAta partition, device: /dev/sda2 Usage: --, Partition flags: --, partition label:-- warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -system 210 Mb FAt, usage: Filesystem, partition type: EFI system Partition, Partition Flags:--, Label: system, Device: /dev/sda1, partition label: EFI system partition, Capacity 210MB, avilable:--, Mount Point: mounted at /boot/efi -134 Mb NTFS, usage: filesystem, partition type: linux basic data partition, partition flags:.--, device: /dev/sda7, partition label: --, capacity: 134MB,available:--, mount point: not mounted -OS 250 GB NTFS, usage: file system, partititon type: linux basic data partition, partition flags: --, type: NTFS, label: OS, device: /dev/sda3, partition label: basic data partition, capacity: 250 GB, available:-, mount point: not mounted -10GB FAT 32, usage: filesystem, partition type: EFI system partition, partition flags:--, type: FAT 32, label: --, device: /dev/sda4, partition label: --, capacity: 10GB, available:--, mount point: not mounted warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -10gb ext 4, usage: file system, partition type: linux basic data partition, partition flags:--, type: EXT4(version1) label:--, device: /dev/sda9, partition label:--, capacity: 10 GB, available:--, mount point at / warning: the partition is misaligned by 1536 bytes. this may result in very poor performance. repartitioning is suggested. -478GB ext4, usage: filesystem, partition type: linux basic data partition, partition flags:--, type: EXT4, label:--, device: /dev/sda5, partition label:--, capacity: 478gb, available:--, mount point: mounted at /home warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. -2.0gb Swap 2.0Gb, usage: swap space, partition type: linux swap partitioin, partition flags:-, device: /dev/sda6, partition label: capacity: 2.0gb warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. and as you can see it is not well organized so please help me to organize the partitions witahout uninstalling the w7, and if possible the grub2

  Read the article

• Collapsing Bookmarks

  - by Tim Dexter

  I said I would tackle documenting some of the new features in the 10.1.3.4.1 roll up patch I mentioned last week. With the patch you can now set the default state of bookmarks (if you create them) in your PDF outputs. If your users prefer to see them all collapsed to the base level or may be collapsed to the second level to ease navigation; whatever they need. Its another opportunity for you to look like a star! You of course need to start with a table of contents; then add the convert|copy to bookmarks command. You can then add the new collapse command to set the appropriate level in the bookmarks. <?copy-to-bookmark:?> <?collapse-bookmark:show;2?> <<< Table of Contents >>> <?end convert-to-bookmark?> The command allows you to expand or collapse the bookmarks as you need. Of course you will know how many levels you will have in the final output document. The command takes the form: <?collapse-bookmark:show|hide;level int?> Some examples <?collapse-bookmark:hide;1?> <?collapse-bookmark:hide;2?> <?collapse-bookmark:hide;3?> Sample template and data here. Dont forget you need that 10.1.3.4.1 roll up!

  Read the article

• How to import Opera Mobile 9 bookmarks into Opera 10 Mobile Beta 3

  - by sajee

  On my Samsung Saga, I've been using the Opera 9 as my default browser. I just installed Opera 10 Beta 3 and I want to import the Opera 9 bookmarks into Opera 10. How do I do that?

  Read the article

• installation of mac os 10.6.2

  - by mahesh

  hi this is mahesh.i had run mac by using vmware workstation 7.0 in my windows pc.i installed mac 10.4.8 os succesfully.but i cant able to install mac10.6.2 version.it shows an error that "invalid front-side bus frequency 66000000 hz,disabling cpu".please help me to solve this and suggest any link to easily understand how to install mac 0s 10.6.2 succesfully.

  Read the article

• sudo equivalent configuration on Solaris 10

  - by daedlus

  I am looking to configure on Solaris 10 to achieve the below: user=jon group=jtu jon is owner of /opt/app user=ken group=jtu ken is owner of /data On Linux I have added the below line %jtu ALL= NOPASSWD: /bin/*, /usr/bin/* so that jon is able to access /data/tmp and delete files. This doesn't work on solaris10 since there is no sudo by default. How do I configure Solaris 10 so jon can delete files in /data/tmp? Thanks

  Read the article

• Keepalived alternative for Solaris 10

  - by antispam

  We are considering an architecture like the one in the picture for Solaris 10 That is, high avalaibility software load balancers in front of web and application servers. Unfortunately, Keepalived is not available for Solaris at the moment. Is there an equivalent artifact for substituing Keepalived which is supported in Solaris 10? Is there an equivalent architecture for Solaris using HA SW load balancing? Thank you.

  Read the article

• 10" display CULV ultraportable?

  - by davr

  Are there any ~10" Intel CULV-based ultraportable notebooks/netbooks? Seems like at 10" the only option is the Atom-based netbooks, I would like something this small but I am willing to pay a bit more for the faster CULV Intel processors. Does anything like this exist?

  Read the article

• manual install perl-5.10.1-3.tar.bz2 on cygwin

  - by Jason

  Hi, I have the binaries: perl-5.10.1-3.tar.bz2 and I don't have access (admin privileges) to run setup.exe for cygwin, my question is how can I install manually inside cygwin the module for perl: perl-5.10.1-3.tar.bz2 ? (or maybe can I get the sources and compile? can someone tell me please how?) thanks

  Read the article

• Mac OS X 10.6.3 update freezes mouse

  - by Kriem

  Ever since I updated my early 2010 MacBook Pro 13" with the 10.6.3 update, the mouse pointer freezes for 5 to 10 seconds, every now and then. The keyboard is next to unresponsive when this happens. Are there more people having the same problem? Is this a known bug? Is there a solution?

  Read the article

• Mac OS X 10.6.3 update freezes mouse every now and then

  - by Kriem

  Ever since I updated my early 2010 MacBook Pro 13" with the 10.6.3 update, the mouse pointer freezes for 5 to 10 seconds, every now and then. The keyboard is next to unresponsive when this happens. Are there more people having the same problem? Is this a known bug? Is there a solution?

  Read the article

• what is the hardware configuration required for the mac os 10.5.8 and mac os 10.6.2.

  - by uttam

  i am having mac mini with mac os 10.4.11, with 512mb of ram and now i want to install the iphone sdk 3.2 but it is giving me error that it requir mac os 10.6.2. can i install mac os 10.6.2 with my old mac mini hardware configuration.

  Read the article

• Radeon HD4850 serious issues when using DirectX 10

  - by ricsmania

  Hello, I have a problem with my video card. Whenever I run a DirectX 10 game, it works for a few seconds (10 or so) and then starts displaying nothing but big polygons. I have tested this with Crysis and Resident Evil 5, both have the same problems. The same games running under DirectX 9 work fine, except for some small black squares once in a while. I have the following specs: Asus P7P55D LE Intel Core i5 750 Sapphire Radeon HD4850 1GB 2x2GB Patriot Viper II Sector 5, DDR3 1600 MHz OCZ Stealth X Stream 500SXS 500W At first I thought it could be the video card overheating (it has stock cooling), but the game crashes even when it's running at 50 degrees C, and it's never been higher than 70. I also thought it could be the PSU, but as far as I know 500W is enough for this computer, especially because I haven't overclocked anything. My OS is Windows 7 X64 and I am using Catalyst 10.10, but I have also tried many older versions with no success. I don't think there is a problem with the card itself, or else it wouldn't run DirectX 9 games I believe. I have spent many hours searching for a solution but I couldn't, so any help is appreciated. Thank you. EDIT: I did some further investigation about the problem, and it seems taspeotis was right, it might be related to memory. I slightly underclocked the memory from 993 to 965 MHz and the problem went away completely. Both the black squares using DirectX 9 and the weird polygons using DirectX 10. I was using RE DirectX 10 Benchmark, as it consistently crashed around the same point, and now I can play the full benchmark with no artifacts at all. Unfortunately, the underclock has an obvious hit in performance. Although it's not critical, it's definitely noticeable. So, if the video memory test software showed no erros, but the card needs an underclock to work, what might be the problem? Temperature? Voltage? By the way, I couldn't find what the default voltage for this card is. And what is a good software to try and increase it? I tried Ati Tray Tools but it has a bug that increases the clock speed dramatically whenever I change something in the Overclock tab, so I'm afraid it might fry my card. Worst case scenario, if I don't find I solution I will try to slightly increase the GPU clock to compensate for the memory clock. Thank you again.

  Read the article

• Software Raid 10 on VirtualBox?

  - by user791022

  I want to learn how to use Software Raid 10, is it possible to use VirtualBox by adding four storage images? This is my plan: 4x 100mb partitions (1 on each drive) configured as a raid 1 for /boot in ext3. Then with the remaining space on each drive, setup a software raid partition and configure it to to LVM and raid 10. In the LVM, set up a 4gb swap partition and the remaining space as the root partition ( / ) as ext3.

  Read the article

• Ubuntu Touch Porting - Audio

  - by user205695

  I'm currenty trying to port Ubuntu Touch to the Galaxy s4 International LTE (GI9505/ jfltexx). I've come to the point where I need to create a UCM directory but I don't know where and how I should call it. By "looking at /usr/share/alsa/ucm/apq8064-tabla-snd-card/" is the local Ubuntu PC directory or a directory on the downloaded CM meant? Same thing for "/proc/asound/cards" which should give a hint about what the directory should be called. 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xfb200000 irq 51 1 [NVidia ]: HDA-Intel - HDA NVidia HDA NVidia at 0xfb080000 irq 17 I dont think the directory should be called anything like this. Thanks for the help Robin Kertels

  Read the article

• MP3 files cut off in the Ubuntu One Android app

  - by rudefyet

  I noticed today on my phone (Droid X running Android 2.2.1) that when streaming the Ubuntu One app would skip to the next song before the previous one had finished. Looking into it, one of the mp3s downloaded from the server was only 2.5MB instead of 4.2MB as it shows on the server itself via one.ubuntu.com. It's happened with multiple tracks today (I remember it happening once the first time I used the app too but shrugged it off as a glitch). The app itself shows a star on the playlist item indicating the file was downloaded even though it was apparently cut off for some reason, perhaps lack of good cell coverage, or some sort of dropped connection. It seems like the latter may be happening and instead of showing an error or retrying it just stops and shows the download is complete.

  Read the article

• Installing 12.04 Ubuntu Studio on VMware Workstation 7, won't install VMware Tools

  - by Chase Kelley

  I'm attempting to install Ubuntu Studio 12.04 on my laptop by using VMware Workstation 7.1.5, and I've encountered a problem. The install goes well until the installation of Ubuntu has completed and the installation of VMware Tools starts; after that it just stops. I have waited about an hour and a half and nothing has changed. The installation is on VMware Easy Install, and I am running Windows Vista 32-bit with 3 GB system RAM and 2 GB of RAM on the virtual machine. Any help is greatly appreciated, thank you!

  Read the article

• Problem when attempting to put Ubuntu One in panel (12.04)

  - by Mohd Arafat Hossain

  I wanted to put the Ubuntu One icon in the panel so I could see the progress of my sync but when I try this is what I get.... mohd-arafat-hossain@TUD:~$ sudo apt-get install ubuntuone-indicator [sudo] password for the-ubuntu-documentary: Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ubuntuone-indicator : Depends: indicator-ubuntuone but it is not going to be installed E: Unable to correct problems, you have held broken packages. I have done these following steps before I did the above sudo add-apt-repository ppa:rye/ubuntuone-extras sudo apt-get update I have scanned for broken packages in Synaptic Package Manager but it shows that I have none. Any help?

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >