Search Results

Search found 71406 results on 2857 pages for 'work world'.

Page 70/2857 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• Can't get network bridging to work

  - by Antonis Christofides

  I'm trying to make network bridging to work on a Debian squeeze (I'm experimenting in order to make a QEMU/KVM virtual machine that will be visible to the outside network as if it were a distinct machine). The problem is that when I type brctl addif br0 eth0 then I lose connectivity to the network until I type brctl delif br0 eth0. More specifically, here's how my machine looks like before I do anything (essentially eth0 is listening on 147.102.160.153): root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591848sec preferred_lft 604648sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever 3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 4c:ed:de:8e:44:d7 brd ff:ff:ff:ff:ff:ff 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether ee:7c:88:59:d0:e8 brd ff:ff:ff:ff:ff:ff Now let me add the bridge: root@laura:/home/anthony# brctl addbr br0 root@laura:/home/anthony# ip tuntap add dev tap0 mode tap root@laura:/home/anthony# ip link set tap0 up root@laura:/home/anthony# brctl addif br0 tap0 Until here everything continues to work normally. Finally, I try to add eth0 to the bridge: root@laura:/home/anthony# brctl addif br0 eth0 At this point, I no longer have a network connection. If I try to ping something, it tells "Destination Host Unreachable". The output of ip addr show seems normal: root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591908sec preferred_lft 604708sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever [snip wlan0, vboxnet0 and pan0, which are down and irrelevant] 8: br0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff 9: tap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 500 link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff inet6 fe80::1430:f2ff:fe67:ab75/64 scope link valid_lft forever preferred_lft forever Also: root@laura:/home/anthony# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 147.102.160.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0.0.0.0 147.102.160.200 0.0.0.0 UG 0 0 0 eth0 I can't understand what I'm doing wrong. I want the machine to continue to listen on 147.102.160.153 on eth0, and in addition to that I want to have a tap0 interface, bridged to eth0, that will be available to the guest machine so that the latter listens on another ip address (say 147.102.160.205). (If there's another way to achieve what I want, I'm also interested.)

  Read the article

• how to make bridge networking with KVM work in Fedora19

  - by netllama

  I'm attempting to get several virtual machines setup on a Fedora-19 host system, with the traditional bridge network devices (br0, br1, etc). I've done this many times before with older versions of Fedora (16, 14, etc), and it just works. However, for reasons that I cannot figure out, the bridge doesn't seem to be working in Fedora19. While I can successfully connect to the outside world (local network + internet) from inside a VM, nothing can communicate with the VM from outside (local network). I'm referring to something as trivial as pinging. From inside the VM, I can ping anything successfully (0% packet loss). However, from outside the VM (on the host, or any other system on the same network), I see 100% packet loss when pinging the IP address of the VM. My first question is simply, does anyone else have this working successfully in F19? And if so, what steps did you need to follow? I'm not using NetworkManager at all, its all the network service. There are no firewalls involved anywhere (iptables & firewall services are currently disabled). Here's the current host configuration: # brctl show bridge name bridge id STP enabled interfaces br0 8000.38eaa792efe5 no em2 vnet1 br1 8000.38eaa792efe6 no em3 br2 8000.38eaa792efe7 no em4 vnet0 virbr0 8000.525400db3ebf yes virbr0-nic # more /etc/sysconfig/network-scripts/ifcfg-em2 TYPE=Ethernet BRIDGE="br0" NAME=em2 DEVICE="em2" UUID=aeaa839e-c89c-4d6e-9daa-79b6a1b919bd ONBOOT=yes HWADDR=38:EA:A7:92:EF:E5 NM_CONTROLLED="no" # more /etc/sysconfig/network-scripts/ifcfg-br0 TYPE=Bridge NM_CONTROLLED="no" BOOTPROTO=dhcp NAME=br0 DEVICE="br0" ONBOOT=yes # ifconfig em2 ;ifconfig br0 em2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet6 fe80::3aea:a7ff:fe92:efe5 prefixlen 64 scopeid 0x20<link> ether 38:ea:a7:92:ef:e5 txqueuelen 1000 (Ethernet) RX packets 100093 bytes 52354831 (49.9 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 25321 bytes 15791341 (15.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device memory 0xf7d00000-f7e00000 br0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 10.31.99.226 netmask 255.255.252.0 broadcast 10.31.99.255 inet6 fe80::3aea:a7ff:fe92:efe5 prefixlen 64 scopeid 0x20<link> ether 38:ea:a7:92:ef:e5 txqueuelen 0 (Ethernet) RX packets 19619 bytes 1963328 (1.8 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 11 bytes 1074 (1.0 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 Relevant section from /etc/libvirt/qemu/foo.xml (one of the VMs with this problem): <interface type='bridge'> <mac address='52:54:00:26:22:9d'/> <source bridge='br0'/> <model type='virtio'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> # ps -ef | grep qemu qemu 1491 1 82 13:25 ? 00:42:09 /usr/bin/qemu-system-x86_64 -machine accel=kvm -name cuda-linux64-build5 -S -machine pc-0.13,accel=kvm,usb=off -cpu SandyBridge,+pdpe1gb,+osxsave,+dca,+pcid,+pdcm,+xtpr,+tm2,+est,+smx,+vmx,+ds_cpl,+monitor,+dtes64,+pbe,+tm,+ht,+ss,+acpi,+ds,+vme -m 16384 -smp 6,sockets=6,cores=1,threads=1 -uuid 6e930234-bdfd-044d-2787-22d4bbbe30b1 -no-user-config -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/cuda-linux64-build5.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=localtime -no-shutdown -device piix3-usb-uhci,id=usb,bus=pci.0,addr=0x1.0x2 -drive file=/var/lib/libvirt/images/cuda-linux64-build5.img,if=none,id=drive-virtio-disk0,format=raw,cache=writeback -device virtio-blk-pci,scsi=off,bus=pci.0,addr=0x4,drive=drive-virtio-disk0,id=virtio-disk0,bootindex=1 -netdev tap,fd=25,id=hostnet0,vhost=on,vhostfd=26 -device virtio-net-pci,netdev=hostnet0,id=net0,mac=52:54:00:26:22:9d,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -vnc 127.0.0.1:1 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x5 I can provide additional information, if requested. thanks!

  Read the article

• Set source address to use tun device does not work (Debian Squeeze)

  - by A. Donda

  there have been similar questions on StackExchange but none of the answers helped me, so I'll try a question of my own. I have a VPN connection via OpenVPN. By default, all traffic is redirected through the tunnel using OpenVPN's "two more specific routes" trick, but I disabled that. My routing table is like this: 198.144.156.141 192.168.2.1 255.255.255.255 UGH 0 0 0 eth0 10.30.92.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun1 10.30.92.1 10.30.92.5 255.255.255.255 UGH 0 0 0 tun1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 10.30.92.5 0.0.0.0 UG 0 0 0 tun1 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth0 And the interface configuration is like this: # ifconfig eth0 Link encap:Ethernet HWaddr XX-XX- inet addr:192.168.2.100 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fe8d:acbd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:394869 errors:0 dropped:0 overruns:0 frame:0 TX packets:293489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:388519578 (370.5 MiB) TX bytes:148817487 (141.9 MiB) Interrupt:20 Base address:0x6f00 tun1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.30.92.6 P-t-P:10.30.92.5 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:9885 (9.6 KiB) TX bytes:4380 (4.2 KiB) plus the lo device. The routing table has two default routes, one via eth0 through my local network router (DSL modem) at 192.168.2.1, and another via tun1 through the VPN's gateway. With this configuration, if I connect to a site, the route chosen is the direct one (because it has less hops?): # traceroute 8.8.8.8 -n traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 192.168.2.1 0.427 ms 0.491 ms 0.610 ms 2 213.191.89.13 17.981 ms 20.137 ms 22.141 ms 3 62.109.108.48 23.681 ms 25.009 ms 26.401 ms ... This is fine, because my goal is to send only traffic from specific applications through the tunnel (esp. transmission, using its -i / bind-address-ipv4 option). To test whether this can work at all, I check it first with traceroute's -s option: # traceroute 8.8.8.8 -n -s 10.30.92.6 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 * * * 2 * * * 3 * * * ... This I take to mean that connection using the tunnel's local address as source is not possible. What is possible (though only as root) is to specify the source interface: # traceroute 8.8.8.8 -n -i tun1 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets 1 10.30.92.1 129.337 ms 297.758 ms 297.725 ms 2 * * * 3 198.144.152.17 297.653 ms 297.652 ms 297.650 ms ... So apparently the tun1 interface is working and it is possible to send packets through it. But selecting the source interface is not implemented in my actual target application (transmission), so I would like to get source address selection to work. What am I doing wrong?

  Read the article

• How to make iPhone Cisco VPN client work with ASA with certificate authentication

  - by Ben Jencks

  I have an ASA that's providing IPsec VPN services using certificate authentication (no xauth, just the certs). It works perfectly with the Cisco IPsec VPN Client. Now I'm trying to let iPhones connect. I've installed the CA cert and a client certificate on the iPhone with a profile using iPCU, along with the VPN configuration. Then connecting gives the error "Could not validate the server certificate". Additionally, the ASA logs the error "Received encrypted Oakley Informational packet with invalid payloads". FWIW, I receive the same invalid payload error when trying to use the Snow Leopard IPsec client to connect. Has anyone successfully gotten the iPhone IPsec client to work with certificate auth?

  Read the article

• Getting VMWare ESXi 5.0.0 with RAID using the Intel X79 chipset to work

  - by Deleted

  I have bought a new server where I use the motherboard ASUS P9X79 WS X79 S-2011 ATX. It will be used for virtualization, preferably using VMware vSphere Hypervisor™ (ESXi) if I can get the RAID on my motherboard working with VMWare (it does not detect it). The motherboard has the Intel® X79 chipset, which for RAID controller means vendor ID 8086 (Intel) and model ID 2826. When I boot the ESXi 5.0.0 installation media from my flash drive I can not see drives in the RAID5 set I created. Questions: Is there a VIB file for the RAID controller I can use? I have found one article at http://www.intel.com/support/motherboards/server/sb/CS-033313.htm on getting RAID to work with some Intel controllers, it lists 9 integrated RAID modules it is comptabile with. However, there is no mention of the X79 chipset.

  Read the article

• ServerFault Wiki: How does Subnetting Work?

  - by Kyle Brandt

  How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Serverfault gets lots of subnetting homework questions, so we could use an answer to point them to on serverfault itself. If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? Not looking for links to other sites (unless maybe you have one post with a bunch of good ones). I already know how to subnet, I just thought it would be nice if serverfault had a generic subnetting answer.

  Read the article

• ndiswrapper wlan driver installed, but wlan still does not work

  - by mugetsu

  I'm trying to get my Atheros AR1111 EB-WG PCI wireless adapter to work. Right now wifi is not even detected. I'm on ubuntu 12.04 64bit and I managed to find a xp64bit driver. I followed the exact steps here: https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper And where I do ndiswrapper -l I get something like : {name of driver} : driver installed device ({Chipset ID}) present which shows that the driver installed properly However, after I load the new module : sudo modprobe ndiswrapper nothing happens, and iwconfig shows that I still have no wlan. I tried to do dmseg | grep ndiswrapper, but there were no driver loading errors or anything strange. I also have blacklist ath5k, ath8k in /etc/modprobe.d/blacklist.conf What am I doing wrong? What could be causing this?

  Read the article

• Samsumg WEP470 bluetooth headset won't work in Windows 7

  - by rob

  I'm trying to use my Samsung WEP470 bluetooth headset with Windows 7 for VOIP apps. When I try to "Add a Bluetooth Device" in the control panel, it detects the headset and installs a driver. However, at the end of driver installation, I see the error message, "This device cannot start. (Code 10)" I'm using the Microsoft Bluetooth transceiver that came with my Microsoft IntelliMouse Explorer for Bluetooth, and the mouse works fine. From other Superuser.com posts, it looks like the headset should just work, as long as I have the Bluetooth transceiver's drivers properly installed. Any ideas what I'm doing wrong?

  Read the article

• Keyboard doesn't work after upgrade to Debian Wheezy

  - by mikhail

  After upgrade from lenny to wheezy keyboard and mouse don't work in X (keyboard available before it starts). I looked over internet about this issue and found some solutions: remove xorg.conf (http://forums.debian.net/viewtopic.php?f=7&t=62880) update udev and base-files (http://forums.debian.net/viewtopic.php?f=6&t=64927&p=376136#p376136) remove /run directory (http://forums.debian.net/viewtopic.php?f=6&t=64927&p=376136#p376136) reintall xserver and xorg But, nothing helped me :( Logs of X-server haven't got any messages about keyboard or mouse errors. Below you can see configuration of my system: krestyaninov@xxx# uname -a Linux xxx 3.0.0-1-686-pae #1 SMP Sat Aug 27 16:41:03 UTC 2011 i686 GNU/Linux krestyaninov@xxx# dpkg -l |grep udev ii libgudev-1.0-0 172-1 GObject-based wrapper library for libudev ii libudev0 172-1 libudev shared library ii udev 172-1 /dev/ and hotplug management daemon krestyaninov@xxx# dpkg -l |grep base-files ii base-files 6.5 Debian base system miscellaneous files krestyaninov@xxx# dpkg -l |grep xorg ii xorg 1:7.6+8 X.Org X Window System ... ii xserver-xorg 1:7.6+8 X.Org X server

  Read the article

• Screensaver does not work for one user account, but does for the other

  - by Travesty3

  Both my screensaver and my "turn off monitor" power saver never come on for one user account on my computer, but it does for the other. It worked before. I can't think of anything I did just before this started happening. I'm using Windows 7 Pro SP1 with the default Aero theme, my screensaver is set to Mystify and should come on after 10 minutes. My power saver setting is set to Balanced, the Turn Off Monitor setting is set to 15 minutes, and the Sleep setting is set to Never. This all works absolutely fine on my user account, but if my wife's user account is logged in, it doesn't work. I don't have any antivirus, I'm not using a wireless keyboard or mouse, and I don't have MagicJack. I have restarted the computer many times since I've seen this problem. Anyone have any suggestions?

  Read the article

• Dynamic group membership to work around no nested security group support for Active Directory

  - by Bernie White

  My problem is that I have a number of network administration applications like SAN switches that do not support nested groups from Active Directory Domain Services (AD DS). These legacy administration applications use either LDAP or LDAPS. I am fairly sure I can use Active Directory Lightweight Directory Services (AD LDS) and possibly Windows Authorization Manager to work around this issue; however I am not really sure where to start. I want to end up with: A single group that can be queried over LDAP/LDAPS for all it’s direct members LDAP proxy for user name and password credentials to AD DS Easy way to admin the group, ideally the group would aggregate the nested membership in AD DS. a native solution using freely available components from the Windows stack. If you have any suggestions or solutions that you have previously used to solve this issue please let me know.

  Read the article

• Audio doesn't work on Windows XP guest (WS 7.0)

  - by Mads

  I can't get audio to work with on a Windows XP guest running on VMware Workstation 7.0 and Ubuntu 9.10 host. Windows fails to produce any audio output and the Windows device manager says the Multimedia Audio Controller is not working properly. Audio is working fine in the host OS. When I open Multimedia Audio Controller properties it says: Device status: The drivers for this device are not installed (Code 28) If I try to reinstall the driver I get the following error message: Cannot Install this Hardware There was a problem installing this hardware: Multimedia Audio Controller An Error occurred during the installation of the device Driver is not intended for this platform Has anyone else experienced this problem?

  Read the article

• Making an apache module work only for a particular sub domain

  - by Abhinav Upadhyay

  Hi everyone. I am not a regular webmaster , I am a student working on an internship project which is an Apache2 module, so my knowledge of Apache configuration is limited. I want to configure my module for a particular sub domain of the host server. Lets say I want my module to work only for onclick.localhost , then what are the directives required ? I want the module to be invoked only for the hosts/virtualhosts for which it has been configured explicitly. I know how to setup sub domains in Apache, so that's not a problem. Thanks.

  Read the article

• I Can't Get Ruby on Rails + Passenger + Apache to Work

  - by Luke Crowe

  I'm sorry if this is a stupid question, but I can't get Ruby on Rails to work on my Apache server. I'm using Phusion Passenger (mod_rails, mod_rack) for app deployment. Here is my RoR-specific configuration code in my website's Apache configuration file: Alias /rails /var/www/syyborg.com/ruby/blog/public <Directory /var/www/syyborg.com/ruby/blog/public Options FollowSymLinks AllowOverride None Order Allow,Deny Allow from All </Directory RailsBaseURI /rails Again, I really have very little knowledge of this kind of thing; I have never set up a server from scratch before. Anyways, my rails app, as you can see, is located at /var/www/syyborg.com/ruby/blog/. I am trying to access it from http://[my domain, syyborg.com]/rails. However, when I try to load the site, I get a "403 Forbidden" error. Any help would be greatly appreciated, and I can provide further details if they are required. Thanks in advance!

  Read the article

• VisualSVN Server won't work with AD, will with local accounts

  - by frustrato

  Decided recently to switch VisualSVN from local users to AD users, so we could easily add other employees. I added myself, gave Read/Write privileges across the whole repo, and then tried to log in. Whether I'm using tortoisesvn or the web client, I get a 403 Forbidden error: You don't have permission to access /svn/main/ on this server. I Googled a bit, but only found mention of phantom groups in the authz file. I don't have any of those. Any ideas? It works just fine with local accounts. EDIT: Don't know why I didn't try this earlier, but adding the domain before the username makes it work, ie MAIN/Bob. This normally only works when there are conflicting usernames...one local, one in AD, but for whatever reason it works here too. Kinda silly, but I can live with it.

  Read the article

• Fn + Right Arrow on MacBook Pro does not work as END Key for SuperUser web site

  - by George2

  Hello everyone, I am using a MacBook Pro running Mac OS X 10.5. I am new to this development environment, and previously worked on Windows. I have tried that Fn + Right arrow on Mac works as "END" key on Windows -- which makes cursor move to the end of line, for most application like Word for Mac -- I have tried it works. But I tried Fn + Right Arrow does not work for current question input box of SuperUser. I am wondering how to solve this issue and why? Does anyone have the same issue for me? thanks in advance, George

  Read the article

• Function keys on Dell laptop work double as OEM keys

  - by Factor Mystic

  I'm working with a new Dell Studio 1555, and the F1-F12 keys at the top of the keyboard are dual function with OEM keys such as volume and screen brightness. The problem is, is that the OEM keys are the default, and you have to press the Fn key to get the F- key to work. For example, this means you have to hit Alt+Fn+F4 to close a window, instead of the regular Alt+F4. This is really annoying. Is there a way to reverse the default functions of the F- keys in Windows? Ideally this is possible without some kind of third party hotkey manager.

  Read the article

• standard keyboard doesn't work, but hotkeys do.

  - by alureonissue

  I posted earlier, but I've learned more about the problem since. (windows xp sp3) AVAST found alureon in kbdclass.sys and atapi.sys. I quarantined both files and restarted. keyboard and cdrom weren't working. I uninstalled them in device manager and updated the drivers. That fixed the cdrom but not the keyboard. Oddly, the keyboard hotkeys work (the row of special keys across the top for calculator, windows explorer, mail, browser) but the standard keys do not. I uninstalled and reinstalled SP3 to no avail. Any advice? not sure if I should have reposted this but I thought the hotkeys working might be an important point left out in the first post. Sorry if I'm doing this wrong ;/

  Read the article

• How to make HOME or END keys work in mc running on OS X (ssh)

  - by Sorin Sbarnea

  I installed MacPorts on OS X 10.5 and I found out that when I connect to the computer using SSH and use mc - Midnight Commander - the HOME and END keys do not work. I have to mention that I'm using putty and I am able to use the keyboard very well on Linux machines like Fedora, Ubuntu,... Here is putty keyboard configuration (a configuration I found to be optimal over time): Backspace key: 127 Home/End keys: Standard Function keys: Xterm R6 Cursor keys: Normal Numpad: normal Terminal type string: xterm-color I'm looking for a command line solution/script that does these changes, this make much easier to create a prepare OS script for configuring a new OS.

  Read the article

• Server Fault Wiki: How does Subnetting Work?

  - by Kyle Brandt

  How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Server Fault gets lots of subnetting homework questions, so we could use an answer to point them to on Server Fault itself. If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? Not looking for links to other sites (unless maybe you have one post with a bunch of good ones). I already know how to subnet, I just thought it would be nice if Server Fault had a generic subnetting answer.

  Read the article

• delete key on linux does not work

  - by Gauthier Fleutot

  Hi! My delete key does not work in ubuntu, it does nothing. I understand that this is a common problem, but I could solve it with the information I found elsewhere. I ran xev. Pressing the 'a' key gives: KeyRelease event, serial 30, synthetic NO, window 0x2c00001, root 0x1a6, subw 0x0, time 7255643, (-113,-107), root:(425,300), state 0x2010, keycode 38 (keysym 0x61, a), same_screen YES, XLookupString gives 1 bytes: (61) "a" XFilterEvent returns: False Pressing 'Delete' gives: FocusOut event, serial 30, synthetic NO, window 0x2c00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 30, synthetic NO, window 0x2c00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 30, synthetic NO, window 0x0, keys: 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 From there I don't know what to do. Help?

  Read the article

• How to free port 80 for xampp to work

  - by Alfie

  Please help, I used to be running xampp and it was working perfectly. Then I wanted to try something out and I ran IIS instead of xampp. Now I want to go back to using xampp, but whenever I try to run the apache server it says: Busy... Apache started [port 80] If I go to http://localhost/ then it just says that it can't establish a connection to the server. I have turned off IIS, so I don't see why it shouldn't work. Any suggestions?

  Read the article

• Server 2008 R2 .Net 4 Programs running from Network share won't work

  - by Lim

  we have several .Net Apps stored on a Network share on our old Server (Windows Server 2003). These Apps get called by Windows 7 32bit Clients and work perfectly fine. We recently wanted to upgrade our Server to Windows Server 2008 R2 and moved the Apps from the old share to our new share on the new Server. The problem started right afterwards since all of our .Net Programs won't start anymore from the new share (2008 R2). The Error that comes up is: "This application could not be started." and with a link to Microsoft: http://support.microsoft.com/kb/2715633 (This Error also shows up when i start a simple console HelloWorld from the server share created in VS2012) Does anyone have any Idea why this is not working anymore on the new Servershare? We've been searching for two days now with no result at all. Any Tips / Help / Questions appreciated :) Greetings Lim

  Read the article

• how to use SharePoint to manage work items (tasks)

  - by George2

  Hello everyone, I am using SharePoint 2007 Enterprise + Publishing portal template + Windows Server 2008. I want to utilize SharePoint to manage work items and I want to let gurus here to recommend me some good tutorials for newbie like me for this field (better through configuration ways, not through coding). My requirements are, Manager could assign task to workers, and manager could edit task description, due date; Workers could see the tasks assigned to them, and could update task execution status (may attach some documents); Manager could review all tasks assigned by the manager, and updates by workers; Better to have a calendar view with the tasks. thanks in advance, George

  Read the article

• Audio doesn't work on Windows XP guest (WS 7.0)

  - by Mads

  Hi, I can't get audio to work with on a Windows XP guest running on VMware Workstation 7.0 and Ubuntu 9.10 host. Windows fails to produce any audio output and the Windows device manager says the Multimedia Audio Controller is not working properly. Audio is working fine in the host OS. When I open Multimedia Audio Controller properties it says: Device status: The drivers for this device are not installed (Code 28) If I try to reinstall the driver I get the following error message: "Cannot Install this Hardware There was a problem installing this hardware: Multimedia Audio Controller An Error occurred during the installation of the device Driver is not intended for this platform" Has anyone else experienced this problem?

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >