Search Results

Search found 39497 results on 1580 pages for 'two shoes'.

Page 704/1580 | < Previous Page | 700 701 702 703 704 705 706 707 708 709 710 711  | Next Page >

  • Weird Network Behavior of Home Router

    - by Stilgar
    First of all I would like to apologize because what you are going to read will be long and confusing but I am fighting this issue for 3 days now and am out of ideas. At home I have the following setup 50Mbps Internet connects into a home router A 2 desktop computers connect to router A via standard FTP LAN cables including one where the cable is ~20m long. a second router B connects to router A via standard FTP LAN cable X (~20m long). several devices connect to the wireless network of router B and there are a couple of desktop computers connected to it through FTP LAN cables. For some reason computers connected to router B when it is connected via cable X have very slow Internet connection. It is like 5 times slower than what is expected. This is the actual problem I am trying to solve. Interesting facts If a computer is connected to cable X directly instead of through router B the Internet speed is just fine (up to the 50Mbps I get from the ISP). Tested with two computers. I have tried replacing router B with another router C and the problem persists. If I connect router B via another cable to the same ports with the same settings everything seems to work fine and computers connected to router B have quite fast Internet I have tested mainly via Speedtest.net but I have also achieved similar speeds when downloading a file The upload speed is quite higher than the download speed in all cases. Note that my ISP usually has higher upload speed (unless it manages to hit the 50Mbps cap) It seems like the speed when connecting through router B with cable X is reduced 4-5 times no matter what the original speed is. For example via router B I get 10Mbps speed to local servers where I get 50Mbps when connected on router A. If I use a distant server where the ISP is only able to provide 25Mbps I get 4-5Mbps on router B. WiFi is slower than LAN on both routers (which is normal) but the reduced speed is reduced proportionally for WiFi. In addition the upload speed is normally higher from the ISP and it is also reduced proportionally. I have tried two different network configurations. One where I have NAT behind NAT where router B connects to router A via the WAN port and has its own DHCP. Second where router B connects to router A via standard LAN port and has DHCP disabled. In this configuration router B serves as a switch and the Network Gateway for computers connected to router B is the internal IP address of router A. Both configurations work just fine but both manifest the reduced speed issue. pings seem to work just fine As far as I can tell none of the cables is crossed The RJ45 setup for cable X orange orange-white brown brow-white blue blue-white green green-white This is a big problem for me since cable X passes through walls and floors and is very hard to replace. I also may have gotten some of the facts wrong because I am almost going crazy with this issue and testing includes going several floors up and down the staircase. One hypothesis I came up with is that the cable is defective in such a way that the voltage from the router affects its performance. When it is connected to a computer it performs just fine but the router has less power. Related hypothesis includes the cable being affected by electricity cables in the walls when the voltage is low. (I know nothing about electricity) So any ideas what to do, what to test or what the issue may be?

    Read the article

  • Is the Cloud ready for an Enterprise Java web application? Seeking a JEE hosting advice.

    - by Jakub Holý
    Greetings to all the smart people around here! I'd like to ask whether it is feasible or a good idea at all to deploy a Java enterprise web application to a Cloud such as Amazon EC2. More exactly, I'm looking for infrastructure options for an application that shall handle few hundred users with long but neither CPU nor memory intensive sessions. I'm considering dedicated servers, virtual private servers (VPSs) and EC2. I've noticed that there is a project called JBoss Cloud so people are working on enabling such a deployment, on the other hand it doesn't seem to be mature yet and I'm not sure that the cloud is ready for this kind of applications, which differs from the typical cloud-based applications like Twitter. Would you recommend to deploy it to the cloud? What are the pros and cons? The application is a Java EE 5 web application whose main function is to enable users to compose their own customized Product by combining the available Parts. It uses stateless and stateful session beans and JPA for persistence of entities to a RDBMS and fetches information about Parts from the company's inventory system via a web service. Aside of external users it's used also by few internal ones, who are authenticated against the company's LDAP. The application should handle around 300-400 concurrent users building their product and should be reasonably scalable and available though these qualities are only of a medium importance at this stage. I've proposed an architecture consisting of a firewall (FW) and load balancer supporting sticky sessions and https (in the Cloud this would be replaced with EC2's Elastic Load Balancing service and FW on the app. servers, in a physical architecture the load-balancer would be a HW), then two physical clustered application servers combined with web servers (so that if one fails, a user doesn't loose his/her long built product) and finally a database server. The DB server would need a slave backup instance that can replace the master instance if it fails. This should provide reasonable availability and fault tolerance and provide good scalability as long as a single RDBMS can keep with the load, which should be OK for quite a while because most of the operations are done in the memory using a stateful bean and only occasionally stored or retrieved from the DB and the amount of data is low too. A problematic part could be the dependency on the remote inventory system webservice but with good caching of its outputs in the application it should be OK too. Unfortunately I've only vague idea of the system resources (memory size, number and speed of CPUs/cores) that such an "average Java EE application" for few hundred users needs. My rough and mostly unfounded estimate based on actual Amazon offerings is that 1.7GB and a single, 2-core "modern CPU" with speed around 2.5GHz (the High-CPU Medium Instance) should be sufficient for any of the two application servers (since we can handle higher load by provisioning more of them). Alternatively I would consider using the Large instance (64b, 7.5GB RAM, 2 cores at 1GHz) So my question is whether such a deployment to the cloud is technically and financially feasible or whether dedicated/VPS servers would be a better option and whether there are some real-world experiences with something similar. Thank you very much! /Jakub Holy PS: I've found the JBoss EAP in a Cloud Case Study that shows that it is possible to deploy a real-world Java EE application to the EC2 cloud but unfortunately there're no details regarding topology, instance types, or anything :-(

    Read the article

  • Postfix on Snow Leopard unable to send MIME emails, including header contents in message body

    - by devvy
    I configured postfix on snow leopard by adding the following line to /etc/hostconfig: MAILSERVER=-YES- I then configured postfix to relay through my ISP's SMTP server. I added the following two lines in their respective places within /etc/postfix/main.cf: myhostname = 1and1.com relayhost = shawmail.vc.shawcable.net I then have a simple PHP mail function wrapper as follows: send_email("[email protected]", "[email protected]", "Test Email", "<p>This is a simple HTML email</p>"); echo "Done"; function send_email($from,$to,$subject,$message){ $header="From: <".$from."> "; $header.= 'MIME-Version: 1.0' . " "; $header.= 'Content-type: text/html; charset=iso-8859-1' . " "; $send_mail=mail($to,$subject,$message,$header); if(!$send_mail){ echo "ERROR"; } } With this, I am receiving an e-mail that appears to be improperly formatted. The message header is showing up in the body of the e-mail. The raw message content is as follows: Return-Path: <[email protected]> Delivery-Date: Tue, 27 Apr 2010 18:12:48 -0400 Received: from idcmail-mo2no.shaw.ca (idcmail-mo2no.shaw.ca [64.59.134.9]) by mx.perfora.net (node=mxus2) with ESMTP (Nemesis) id 0M4XlU-1NCtC81GVY-00z5UN for [email protected]; Tue, 27 Apr 2010 18:12:48 -0400 Message-Id: <[email protected]> Received: from pd6ml3no-ssvc.prod.shaw.ca ([10.0.153.149]) by pd6mo1no-svcs.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:47 -0600 X-Cloudmark-SP-Filtered: true X-Cloudmark-SP-Result: v=1.0 c=1 a=VphdPIyG4kEA:10 a=hATtCjKilyj9ZF5m5A62ag==:17 a=mC_jT1gcAAAA:8 a=QLyc3QejAAAA:8 a=DGW4GvdtALggLTu6w9AA:9 a=KbDtEDGyCi7QHcNhDYYwsF92SU8A:4 a=uch7kV7NfGgA:10 a=5ZEL1eDBWGAA:10 Received: from unknown (HELO 1and1.com) ([24.84.196.104]) by pd6ml3no-dmz.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:48 -0600 Received: by 1and1.com (Postfix, from userid 70) id BB08D14ECFC; Tue, 27 Apr 2010 15:12:47 -0700 (PDT) To: [email protected] Subject: Test Email X-PHP-Originating-Script: 501:test.php Date: Tue, 27 Apr 2010 18:12:48 -0400 X-UI-Junk: AutoMaybeJunk +30 (SPA); V01:LYI2BGRt:7TwGx5jxe8cylj5nOTae9JQXYqoWvG2w4ZSfwYCXmHCH/5vVNCE fRD7wNNM86txwLDTO522ZNxyNHhvJUK9d2buMQuAUCMoea2jJHaDdtRgkGxNSkO2 v6svm0LsZikLMqRErHtBCYEWIgxp2bl0W3oA3nIbtfp3li0kta27g/ZjoXcgz5Sw B8lEqWBqKWMSta1mCM+XD/RbWVsjr+LqTKg== Envelope-To: [email protected] From: <[email protected]> MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 Message-Id: <[email protected]> Date: Tue, 27 Apr 2010 15:12:47 -0700 (PDT) <p>This is a simple HTML email</p> And here are the contents of my /var/log/mail.log file after sending the email: Apr 27 15:29:01 User-iMac postfix/qmgr[705]: 74B1514EDDF: removed Apr 27 15:29:30 User-iMac postfix/pickup[704]: 25FBC14EDF0: uid=70 from=<_www> Apr 27 15:29:30 User-iMac postfix/master[758]: fatal: open lock file pid/master.pid: unable to set exclusive lock: Resource temporarily unavailable Apr 27 15:29:30 User-iMac postfix/cleanup[745]: 25FBC14EDF0: message-id=<[email protected]> Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: from=<[email protected]>, size=423, nrcpt=1 (queue active) Apr 27 15:29:30 User-iMac postfix/smtp[747]: 25FBC14EDF0: to=<[email protected]>, relay=shawmail.vc.shawcable.net[64.59.128.135]:25, delay=0.21, delays=0.01/0/0.1/0.1, dsn=2.0.0, status=sent (250 ok: Message 25784419 accepted) Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: removed Two other people in the office have followed the exact same process and are running the exact same script, version of snow leopard, php, etc. and everything is working fine for them. I've even copied their config files to my machine, restarted postfix, restarted apache, all to no avail. Does anyone know what steps I could take to resolve the issue? This is boggling my mind... Thanks

    Read the article

  • Upgraded Ubuntu, all drives in one zpool marked unavailable

    - by Matt Sieker
    I just upgraded Ubuntu 14.04, and I had two ZFS pools on the server. There was some minor issue with me fighting with the ZFS driver and the kernel version, but that's worked out now. One pool came online, and mounted fine. The other didn't. The main difference between the tool is one was just a pool of disks (video/music storage), and the other was a raidz set (documents, etc) I've already attempted exporting and re-importing the pool, to no avail, attempting to import gets me this: root@kyou:/home/matt# zpool import -fFX -d /dev/disk/by-id/ pool: storage id: 15855792916570596778 state: UNAVAIL status: One or more devices contains corrupted data. action: The pool cannot be imported due to damaged devices or data. see: http://zfsonlinux.org/msg/ZFS-8000-5E config: storage UNAVAIL insufficient replicas raidz1-0 UNAVAIL insufficient replicas ata-SAMSUNG_HD103SJ_S246J90B134910 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 UNAVAIL ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 UNAVAIL The symlinks for those in /dev/disk/by-id also exist: root@kyou:/home/matt# ls -l /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910* /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51* lrwxrwxrwx 1 root root 9 May 27 19:31 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910 -> ../../sdb lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part9 -> ../../sdb9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523 -> ../../sdd lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part9 -> ../../sdd9 lrwxrwxrwx 1 root root 9 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969 -> ../../sde lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1 -> ../../sde1 lrwxrwxrwx 1 root root 10 May 27 19:15 /dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part9 -> ../../sde9 Inspecting the various /dev/sd* devices listed, they appear to be the correct ones (The 3 1TB drives that were in a raidz array). I've run zdb -l on each drive, dumping it to a file, and running a diff. The only difference on the 3 are the guid fields (Which I assume is expected). All 3 labels on each one are basically identical, and are as follows: version: 5000 name: 'storage' state: 0 txg: 4 pool_guid: 15855792916570596778 hostname: 'kyou' top_guid: 1683909657511667860 guid: 8815283814047599968 vdev_children: 1 vdev_tree: type: 'raidz' id: 0 guid: 1683909657511667860 nparity: 1 metaslab_array: 33 metaslab_shift: 34 ashift: 9 asize: 3000569954304 is_log: 0 create_txg: 4 children[0]: type: 'disk' id: 0 guid: 8815283814047599968 path: '/dev/disk/by-id/ata-SAMSUNG_HD103SJ_S246J90B134910-part1' whole_disk: 1 create_txg: 4 children[1]: type: 'disk' id: 1 guid: 18036424618735999728 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51422523-part1' whole_disk: 1 create_txg: 4 children[2]: type: 'disk' id: 2 guid: 10307555127976192266 path: '/dev/disk/by-id/ata-WDC_WD10EARS-00Y5B1_WD-WMAV51535969-part1' whole_disk: 1 create_txg: 4 features_for_read: Stupidly, I do not have a recent backup of this pool. However, the pool was fine before reboot, and Linux sees the disks fine (I have smartctl running now to double check) So, in summary: I upgraded Ubuntu, and lost access to one of my two zpools. The difference between the pools is the one that came up was JBOD, the other was zraid. All drives in the unmountable zpool are marked UNAVAIL, with no notes for corrupted data The pools were both created with disks referenced from /dev/disk/by-id/. Symlinks from /dev/disk/by-id to the various /dev/sd devices seems to be correct zdb can read the labels from the drives. Pool has already been attempted to be exported/imported, and isn't able to import again. Is there some sort of black magic I can invoke via zpool/zfs to bring these disks back into a reasonable array? Can I run zpool create zraid ... without losing my data? Is my data gone anyhow?

    Read the article

  • Server Admin is not allowing me to configure DNS

    - by Clinton Blackmore
    We have a Mac OS X 10.5.8 Server running DNS (and a few other services). When I connect to it (using Server Admin 10.5.3 [which comes from the Server Admin 10.5.7 tools]), and click to look at the DNS settings, all appears normal -- it shows many reverse entries and two top-level domains. However, when I select one of our domains and open the disclosure triangle, the list is empty! [There should be over a dozen entries, and the reverse entries do show up.] If I then tell it I want to add, say, an A Record to the domain, almost everything disappears -- and I am left with a list showing our two domains, one with a disclosure triangle underneath it showing a single entry, and one reverse entry to correspond to the new A record. named appears to be working fine. DNS names resolve. It appears to simply be that Server Admin is having problems with the data on the computer. No one here would have manually created a DNS entry. Now, while I think I've backed up the DNS (I backed up /var/named/, /etc/named.conf, and /etc/dns/, as mentioned here), I'm really not sure if just replacing the files would restore the DNS settings we have if things go south. I am contemplating going to settings and changing the log level from "Information" to "Debug", but 1) I am just a little concerned that it might write a bad configuration to the disk, and 2) I think it would only affect named and not Server Admin, and, so far as I can tell, named is not having a problem. (Nothing looks strange in /Library/Logs/named.log when I open it via Console/Terminal. Oddly, though, when I click on the 'log' button for DNS in Server Admin, I see no text at all, just a fully white window. When I look at one of our secondary DNS servers, I am able to see the log file through Server Admin.) This entry appears in the system log when I run Server Admin on the server: Jun 17 09:02:08 od1 Server Admin[3892]: Unexpected call to doMarkConfigurationAsDirty by 'DNS' plugin during updateConfigurationViewFromDescription It seems to occur after I've looked at DNS, look at another service, and then click back on DNS. Think that the most likely cause is a corrupt configuration file, I glanced through all the files that I backed up, and none of them is obviously gobbledygook. Here are some oddities I find when running Server Admin from a remote computer to manage the DNS. When I click to see the log file for DNS, the server starts writing messages like these to its system.log: Jun 17 09:59:04 od1 kernel[0]: Limiting open port RST response from 252 to 250 packets per second Jun 17 09:59:06 od1 kernel[0]: Limiting open port RST response from 258 to 250 packets per second This stops when I click on a different service. The inderterminate progress indicator (the spinning wheel that appears beside the "Revert" and "Save" buttons in the bottom-right corner of Server Admin) looks really strange. As far as I can tell, instead of just spinning and waiting, it is being told to start spinning repeatedly, resulting in a jerky animation. Here are some of the messages being logged on the computer running Server Admin: At startup: *** ERROR: -[GRAxes computeLayout]:1124 - plotRect height = 0.000000 <= 0.0 *** *** ERROR: -[GRChartView computeLayout]:1194 - Layout for overlay axes (0x18758f50) failed. *** (These messages don't concern me too much as they go away for a while if you delete ~/Library/Preferences/com.apple.ServerAdmin.plist). At shutdown: 2010-06-17 10:02:17.202 Server Admin[7770:10b] *** -[GroupTextField windowDidResignKey:]: unrecognized selector sent to instance 0x16e12490 More concerning are these messages: 2010-06-17 09:59:47.269 Server Admin[7770:10b] Unexpected call to doMarkConfigurationAsDirty by 'DNS' plugin during updateConfigurationViewFromDescription Server Admin(7770,0xb0453000) malloc: *** error for object 0x1c115390: double free *** set a breakpoint in malloc_error_break to debug 2010-06-17 10:01:00.795 Server Admin[7770:10b] *** -[ServiceEntry sessionHost]: unrecognized selector sent to instance 0x2af500 Any thoughts on: what the problem is how I can troubleshoot it or how to fix it? If I do need to wipe out DNS and restart, is there a good way to do this?

    Read the article

  • How to recover data files from xampp-windows to xampp-linux after crash?

    - by David Buehler
    My Windows box died after I developed a database in xampp on it; fortunately I have a backup of the entire F:/TestWeb/Xampp partition. Unfortunately, I did not do an Export (nor dump) of the "Lws2" database before the crash. I have replaced the defunct machine with one running Mint7 (based on Ubuntu 9.04 "Jaunty Jackalope") and installed xampp-linux into the /opt partition, so the new xampp now runs fine in /opt/lampp, and says all the elements are secured by passwords (which I just assigned during this installation.) I assumed that Xamp-Windows installed in November would migrate easily to xampp-linux installed iin February -- a bad assumption. It apparently would have been simple if I had known enough to do an Export or a Dump before the crash, but.... The backup was done to a Network Attached Storage drive, which is formatted as "vfat" so the backup does not carry with it any valid ownership permissions from MySql on NTFS. I now see from my backup that the old data resided in \TestWeb\Xampp\Mysql\Data\Lws2\ and consists of 7 ".frm" files which define my tables. The actual data -- I suppose a ".sql" file or files -- has disappeared, and I am resigning myself to two days of retyping it. But I do not wish to do the table layouts all over again. So I copied Data tree to /opt/lampp/Data -- PhpMyAdmin does not see it. So I copied Lws2 tree to /opt/lampp/Lws2 -- PhpMyAdmin does not see it. So I copied Data tree to /opt/lampp/var/mysql/Data -- PhpMyAdmin does not see it. So I copied Lws2 tree to /opt/lampp/var/mysql/Lws2 -- PhpMyAdmin does not see it. So I adjusted all the permissions to stop saying owner "nobody" to owner "root" and gave full permissions to all groups and to all others, with permissions percolating down, in all 4 trees. You guessed it -- PhpMyAdmin does not see any database named Lws2, only its 4 default ones. I double-checked the permissions and rebooted Linux and repeated the tests. At some point in that process I did see PhpMyAdmin showing "lws2(7)" but when I clicked on it I saw a "no table found" message. I have not been able to recreate that experience. Apparently there are some setup files for MySql and for PhpMyAdmin which need to be set up by running a wizard or two or by editing the files directly. I grepped the TestWeb tree and found an old "ldir = "C:TestWeb\Xampp\MySql\" and a "DataDir = C:TestWeb\Xampp\MySql\" in a .php file and in a .bat file, but I cannot find the corresponding config file names on the /opt partition/ -- so it looks as if these wizards have not been run to create them. What config files files does Linux use to setup MySql config files for PhpMyAdmin? What wizards do I need to run to point the MySql engine and the PhpMyAdmin at the folder /opt/lampp/data/ with its lws2 folder inside it? Or which files do I need to edit, with a sample of what it normally says under Linux? Incidentally, I remember I converted from MyISAM with its .MYD and .MYI files to InnoDB after entering only a small amount of the data -- and I do not know what file types to look for -- perhaps my data is still there but under another guise or in another place? Is it something as simple as linux needing to see "/data/" instead of /Data? I will check that out while waiting for a response. If anyone can point me to documentation that discusses this level of detail -- I will read it avidly! In any case, thanks for any clarification you can give on this thorny problem. wizdum

    Read the article

  • How to configure multiple iSCSI Portal Groups on a EqualLogic PS6100?

    - by kce
    I am working on a migration from a VMware vSphere environment to a Hyper-V Cluster utilizing Windows Server 2012 R2. The setup is pretty small, an EqualLogic PS6100e and two Dell PowerConnect 5424 switches and handful of R710s and R620s. The SAN was configured as a non-RFC1918 network that is not assigned to our organization and since I am working on building a new virtualization environment I figured that this would be an appropriate time to do a subnet migration. I configured a separate VLAN and subnet on the switches and the two previously unused NICs on the PS6100's controllers. At this time I only have a single Hyper-V host cabled in but I can successfully ping the PS6100 from the host. From the PS6100 I can ping each of the four NICs that currently on the storage network. I cannot connect the Microsoft iSCSI Initiator to the Target. I have successfully added the Target Portals (the IP addresses of PS6100 NICs) and the Targets are discovered but listed as inactive. If I try to Connect to them I get the following error, "Log onto Target - Connection Failed" and ISCSIPrt 1 and 70 events are recorded in the Event Log. I have verified that access control to the volume is not the problem by temporarily disabling it. I suspect the problem is with the Portal Group IP address which is still listed as Group Address of old subnet (I know, I know I might be committing the sin of the X/Y problem but everything else looks good): RFC3720 has this to say about Network Portal and Portal Groups: Network Portal: The Network Portal is a component of a Network Entity that has a TCP/IP network address and that may be used by an iSCSI Node within that Network Entity for the connection(s) within one of its iSCSI sessions. A Network Portal in an initiator is identified by its IP address. A Network Portal in a target is identified by its IP address and its listening TCP port. Portal Groups: iSCSI supports multiple connections within the same session; some implementations will have the ability to combine connections in a session across multiple Network Portals. A Portal Group defines a set of Network Portals within an iSCSI Network Entity that collectively supports the capability of coordinating a session with connections spanning these portals. Not all Network Portals within a Portal Group need participate in every session connected through that Portal Group. One or more Portal Groups may provide access to an iSCSI Node. Each Network Portal, as utilized by a given iSCSI Node, belongs to exactly one portal group within that node. The EqualLogic Group Manager documentation has this to say about the Group IP Address: You use the group IP address as the iSCSI discovery address when connecting initiators to iSCSI targets in the group. If you modify the group IP address, you might need to change your initiator configuration to use the new discovery address Changing the group IP address disconnects any iSCSI connections to the group and any administrators logged in to the group through the group IP address. Which sounds equivalent to me (I am following up with support to confirm). I think a reasonable explanation at this point is that the Initiator can't complete the connection to the Target because the Group IP Address / Network Portal is on a different subnet. I really want to avoid a cutover and would prefer to run both subnets side-by-side until I can install and configure each Hyper-V host. Question/s: Is my assessment at all reasonable? Is it possible to configure multiple Group IP Addresses on the EqualLogic PS6100? I don't want to just change it as it will disconnect the remaining ESXi hosts. Am I just Doing It Wrong(TM)?

    Read the article

  • Windows Server 2012 Migration (DNS/AD DS Standard Eval to Essentials OEM) P2V -> Do I need a Secondary Domain Controller during migration?

    - by Aubrey Robertson
    This is my first post on this exchange (although not my first on stack exchange), so please have patience. I am a 3rd year student intern, and I have been tasked with virtualizing the server systems at the company I work for. I have come a long way, and I am almost ready to install the VM Server in migration mode. Here is some information: Source Server: Windows Server 2012 Standard Evaluation DNS Server (local only) Advanced Directory Domain Services File and Storage stuff A few other server roles Destination Server: Windows Server 2012 Essentials OEM (Hyper-V client) Running under a temporary Hyper-V host (will migrate the Hyper-V host back to the old machine after the original server is virtualized as a client). Sitting currently at the "Select Installation Mode" screen. I have been following the guides on Microsoft tech net, and today I spent most of the day getting rid of issues in the Best Practices Analyser on the source machine. I have 3 remaining issues (which are all related): ERROR: DNS: DNS servers on Ethernet (adapter name) should include the loopback address, but not as the first entry (flavour text indicates that, during migration, the DNS server may not be found) WARNING: All domains should have at least two domain controllers for redundancy. WARNING: DNS: Ethernet should be configured to use both a preferred and an alternate DNS Server. All of these issues can be resolved by deploying a secondary domain controller, but I have never done that before (see my concerns below). The main issue here that I am concerned with for installing in migration mode is the FIRST one (the error). If I try and set-up the new server deployment, and the adapter domain controller is listed as localhost, then this may cause the installation to fail. (at least, this is what the Microsoft documentation suggests). But I do not have another IP address to enter here as I have no other local domain controllers. So I did the first obvious thing that came to my mind, and tried to use Google DNS servers as my alternates. That did not work because they couldn't recognize other computers in the "forest". Now I'm no expert when it comes to DNS, so please forgive my ignorance. This DNS server is concerned only with Active Directory stuffs for the local network. If I go ahead with migration, and it fails, then I will just have to go ahead and install a secondary DNS server I suppose. The problem I have here is that I am limited by the amount of Windows Server keys I have available (I have 2); however, I do have access to a Linux box running Debian Wheezy that I set-up two weeks ago as a Mantis server. I could install Windows Server 2012 as a secondary DNS (I think) in a VM and use that, but then it seems like I will be wasting time, and probably the Windows key too, and if there's another way to do it with Linux that would be much better. Even better still, do I even need a secondary DNS server for migration at all? The hints said that during migration the original machine "might" not be found. Thank you for your time and consideration.

    Read the article

  • Moving users folder on Windows-7 to another partition - bad idea?

    - by Donat
    Hi, I'd like to re-submit here a question posted by Benjol on Aug 17at 5:57 "Moving users folder on Windows Vista to another partition - bad idea?" (I can't post one than one link until I earn "10 reputation" and removed my "answer" there to post my follow-up questions here). I am anxiously getting ready at long last to to carry out a clean install (using custom install option) from Vista to Windows-7 Home Premium 64bit with the free upgrade I received late October. For my Vista system I successfully set-up last Summer a multi-partitions scheme with Users and Program Data on a a different partition than the operating system (see link below, and its subsequent links in my comment for details). http://tuts4tech.net/2009/08/05/windows-7-move-the-users-and-program-files-directories-to-a-different-partition/comment-page-1/#comment-562 I was planning a similar set-up for windows 7, a little more streamlined, with OS, Program Files on C:, Users and Program Data on D:, and TV media recording on a separate partition. Reading the Question submitted by Benjol, I am second guessing too. Is moving Users and Program Data on a different partition than the default primary partition with OS and Program Files such a good idea? The couple of people I talked to at the official Microsoft Windows 7 booth at CES 2010 gave the same answer to the intention of moving the Users profile folder to another partition. In a nutshell, they all told me that they used to do this in XP and less in Vista but not anymore with Windows 7... "It is stable, after two months still no problem" I had the feeling it was a scripted answer to emphasize how Windows 7 is so stable and efficient... (Will Windows-7 system not become bugged down over the course of several months to a year or two? Only time will tell) Long story short, I share the same view than Benjol expressed with respect to being "able to backup and restore system and user data independently." I just received a 2TB usb2, eSATA external hard drive as a back-up drive, which includes NTI Shadow 4 (4.1.0.150) for back-up solution. I took note of the issue with NTUSER.DAT and I will read more about Volume Shadow Copy Service (VSS) for Windows 7. I am willing to put the effort if placing Users and Program Data on a different partition would allow to restore a fresher OS+Program image when the system gets bugged down. Questions: Is it such a bad idea? What is the "easy route" referred by Benjol in his post? Is it to just relocate folders to another partition using the Folder property tool? (It is not practical for several users and might not provide a straightforward restore process of just OS and Program Files when needed.) I am starting to learn about Windows 7 libraries. Would Windows 7 libraries be another alternative to achieve this? All this reading to decide how to organize the partition scheme for my custom system is starting to be confusing. I apologize for this lengthy Question. It is my first day here on SuperUser and I am just learning how different from a discussion thread it is. Thank you in advance for all your suggestions and comments. Donat

    Read the article

  • Nginx and multiple wordpress instances with fastcgi under same domain

    - by damnsweet
    My site is running on apache. two instances of wordpress exist under paths /tr/ and /eng/. I want to move the setup to nginx but could not manage to get it working. My setup consists of nging 0.7.66, php 5.3.2, and php-fpm. /tr/ and /eng/ are two separate wordpress instances located under /home/istci/webapps/wordpress_tr and /home/istci/webapps/wordpress respectively. Below is the server section from nginx.conf containing only configuration for tr, yet could not get it working either. server { listen 80; server_name www.example.com; charset utf-8; location ~ ^/$ { rewrite ^(.+)$ http://www.example.com/tr/ permanent; } location ~ /tr/.*php$ { fastcgi_pass unix:/home/istci/var/run/wptr.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/istci/webapps/wordpress_tr$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param SCRIPT_NAME $fastcgi_script_name; fastcgi_param REQUEST_URI $request_uri; fastcgi_param DOCUMENT_URI $document_uri; fastcgi_param DOCUMENT_ROOT $document_root; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param GATEWAY_INTERFACE CGI/1.1; fastcgi_param SERVER_SOFTWARE nginx/$nginx_version; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; fastcgi_param SERVER_ADDR $server_addr; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_NAME $server_name; # required if PHP was built with --enable-force-cgi-redirect fastcgi_param REDIRECT_STATUS 200; } location /tr/ { root /home/istci/webapps/wordpress_tr/; index index.php index.html index.htm; if (!-e $request_filename) { rewrite ^(.+)$ /tr/index.php?q=$1 last; break; } if (-f $request_filename) { expires 30d; break; } } } php-fpm listens on unix:/home/istci/var/run/wptr.sock. running it in debug-mode shows no active handlers, which means no connection is made to unix socket from nginx. nginx access logs: 127.0.0.1 - - [09/Jun/2010:03:45:11 -0500] "GET /tr/ HTTP/1.0" 404 20 "-" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.2.4) Gecko/20100527 Firefox/3.6.4" nginx debug logs : 2010/06/09 03:38:53 [notice] 6922#0: built by gcc 4.1.2 20080704 (Red Hat 4.1.2-48) 2010/06/09 03:38:53 [notice] 6922#0: OS: Linux 2.6.18-164.9.1.el5PAE 2010/06/09 03:38:53 [notice] 6922#0: getrlimit(RLIMIT_NOFILE): 4096:4096 2010/06/09 03:38:53 [notice] 6923#0: start worker processes 2010/06/09 03:38:53 [notice] 6923#0: start worker process 6924 2010/06/09 03:38:53 [notice] 6923#0: start worker process 6925 2010/06/09 03:39:01 [notice] 6925#0: *1 "^(.+)$" matches "/tr/", client: 127.0.0.1, server: www.example.com, request: "GET /tr/ HTTP/1.0", host: "www.example.com" 2010/06/09 03:39:01 [notice] 6925#0: *1 rewritten data: "/tr/index.php", args: "q=/tr/", client: 127.0.0.1, server: www.example.com, request: "GET /tr/ HTTP/1.0", host: "www.example.com" Any clues about what is wrong with my configuration? Thanks.

    Read the article

  • IP Micro-outages, telephone micro-outages, and CATV micro-outages

    - by Michael Graff
    This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

    Read the article

  • Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

    - by Steven
    We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

    Read the article

  • Issues configuring Exchange 2010 as well as SSL problems.

    - by Eric Smith
    Possibly-Relevant Background Info: I've recently moved up from icky shared hosting to a glorious, Remote Desktop-administrated VPS server running Windows Server 2008 R2. Even though I'm only 21 now and a computer science major, I've tried to play with every Windows Server release since '03, just to learn new things. What usually happens is inevitably I'll do something wrong and pretty much ruin the install. You're dealing with an amateur here :) Through the past few months of working with my new server, I've mastered DNS, IIS, got Team Foundation Server running (yay!), and can install all of the other basics like SQL Server and Active Directory. The Problem: Now, these last few weeks I've been trying to install Exchange Server 2010 (SP1). To make a long story short, it took me several attempts, and I even had to get my server wiped just so I could start fresh since Exchange decided uninstalling properly was for sissies (cost me $20, bah). Today, at long last, I got Exchange mostly working. There were two main problems left, however, that left me unsatisfied: Exchange installed itself and all of its child sites into Default Web Site. I wanted to access Exchange via mail.domain.com, but instead everything was configured to domain.com. My limited server admin knowledge was not enough to configure IIS or Exchange to move itself over to the website I had set up for it, appropriately titled 'mail.domain.com', which I had bound to a dedicated IP address (I was told this was necessary, but he may have been wrong). I have two SSL certificates: one for my main domain and one for my mail subdomain. For whatever reason, I had issues geting Exchange to use my mail certificate, even though I had assigned the proper roles in the MMC. I did, at one point, get it to work (or mostly work, anyways. Frankly, my memory of today is clouded by intense frustration). Additionally, I was confused which type of SSL certificate I should be using for Exchange. My SSL provider, GoDaddy, allows me to request a new certificate whenever, so I can use either the certificate request provided by IIS or the more complicated and specific request you can create with Exchange. Which type should I be using, the IIS or Exchange certificate? If I must use the Exchange certificate, will that 1) cause issues when I bind that certificate to my mail.domain.com subdomain or 2) is that an unnecessary step? The SSL Certificate Strikes Back When I thought I had the proper SSL certificate assigned for those brief, sweet moments, Google Chrome reported the correct mail.domain.com certificate when browsing https://mail.domain.com. However, Outlook 2010 threw up an error when trying to configure my email account claiming that the certificate didn't match the domain of "mail.domain.com". Is this an issue that will be resolved by problem #2 or is it a separate one entirely? Apologies for the massive wall of text, but I wanted to provide as much info as I possibly could. Exchange is the last thing I'd like installed on my server, and naturally it's turning out to be the hardest. Thanks for any info at all. Even a point in a vague direction would be a huge help at this point. Thanks! -Eric P.S.: The reason I keep ruining my install is that when I attempt to uninstall Exchange, something invariably goes wrong. The last time the uninstaller complained that there was still a mailbox active and it couldn't proceed until I deleted it. ... The only mailbox left was the Administrator account, the built-in one I couldn't delete. So I attempted to manually uninstall it following several guides online only to now be stuck unable to launch the installer and have to get my system wiped AGAIN for the second time today ($40 down the drain, bah!). I do not understand at all why "uninstall" just can't mean "hey, you, delete everything and go away". There's not even a force uninstall option, only a "recover system" option that just fails to fix anything and makes it so I can't even use the GUI uninstaller. </rant>

    Read the article

  • Trouble getting SSL to work with django + nginx + wsgi

    - by Kevin
    I've followed a couple of examples for Django + nginx + wsgi + ssl, but I can't get them to work. I simply get an error in my browser than I can't connect. I'm running two websites off the host. The config files are identical except for the ip addresses, server names, and directories. When neither use SSL, they work fine. When I try to listen on 443 with one of them, I can't connect to either. My config files are below, and any suggestions would be appreciated. server{ listen xxx.xxx.xxx.xxx:80; server_name sub.domain.com; access_log /home/django/logs/nginx_customerdb_http_access.log; error_log /home/django/logs/nginx_customerdb_http_error.log; location / { proxy_pass http://127.0.0.1:8080; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } location /site_media/ { alias /home/django/customerdb_site_media/; } location /admin-media/ { alias /home/django/django_admin_media/; } } server{ listen xxx.xxx.xxx.xxx:443; server_name sub.domain.com; access_log /home/django/logs/nginx_customerdb_http_access.log; error_log /home/django/logs/nginx_customerdb_http_error.log; ssl on; ssl_certificate sub.domain.com.crt; ssl_certificate_key sub.domain.com.key; ssl_prefer_server_ciphers on; location / { proxy_pass http://127.0.0.1:8080; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Protocol https; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } location /site_media/ { alias /home/django/customerdb_site_media/; } location /admin-media/ { alias /home/django/django_admin_media/; } } <VirtualHost *:8080> ServerName xxx.xxx.xxx.xxx ServerAlias xxx.xxx.xxx.xxx LogLevel warn ErrorLog /home/django/logs/apache_customerdb_error.log CustomLog /home/django/logs/apache_customerdb_access.log combined WSGIScriptAlias / /home/django/customerdb/apache/django.wsgi WSGIDaemonProcess customerdb_wsgi processes=4 threads=5 WSGIProcessGroup customerdb_wsgi SetEnvIf X-Forwarded-Protocol "^https$" HTTPS=on </VirtualHost> UDPATE: the existence of two sites (on separate IPs) on the host is the issue. if i delete the other site, the setting above mostly work. doing so also brings up another issue: chrome doesn't accept the site as secure saying that some content is not encrypted.

    Read the article

  • apache webserver unresponsible with server-status showing all child processes waiting for connection

    - by Jeff
    My setup: i have 3 nearly identical webserver machines serving the same high loaded dynamic website with simple load balancing over dns. The service has been working for over two ears with the same apache config. apache2, php5, ubuntu 8.04 linux 2.6.24-29-server My problem: since about two weeks i'm experiencing problems with this config. Nearly every day i have one small moment about 5 minutes, in which the website is unreachable. I'm still able to login to the servers over ssh. If i run htop, i see the machine simply doing nothing. i have about 1000 apache processes running, but no cpu activity. i've used the apache mod_status to debug this situation. the process scoreboard looks like this: _C.___K_______________________R._______.__K_K____K___C_______.__ _______C__________.___________________________________.________C _.____K__________K___K_WK_____._K_____________________________._ W______K__________K________.____________________._______C_______ _C_.__K__K____.._.._____________________________________C_______ _R___________K___.______C________.C_________.______._____C______ ____________KKC____K_____K__WC_________________C_____.__.____.__ _____________________C_________K______.____C______._____________ _.___C____.___.___________________________.K______.____K________ W__.___________________C.__.____K________K_______R_._.__._______ __C__C_.__________C__C_______._____W______________C_.___C_______ ____.______C_____________C________.____C____________.________._K __.__________.K_____________K_________._____C____.K__________KW_ __K.W________R_________._______.___W___________.____.__K_____W__ W___.___..________W____K Scoreboard Key: "_" Waiting for Connection, "S" Starting up, "R" Reading Request, "W" Sending Reply, "K" Keepalive (read), "D" DNS Lookup, "C" Closing connection, "L" Logging, "G" Gracefully finishing, "I" Idle cleanup of worker, "." Open slot with no current process So the most of the processes are just waiting for connection. after about 5 minutes the situation will return to normal: i have lot least processes on every machine, the most workers have the "."-status (meaing they are open to process a request) and of course the website is reachable! so i'm trying to find something in the logs, but there is simply nothing... the apache access log is silent for about 4 minutes, the same is for the error log. i also can not figure out anything wrong in other system logs. the situation is the same on all 3 webservers (all of them have this load peak and unresposibility at the same time), so i do not thing this is hardware related. but i think, this might be related to some network (tcp) issue. any ideas? EDIT: some more information, that i have just discovered: it has just happened again. and i was able to verify that i'm also not able to connect locally when this problem occurs. i have made some connection statistics with the following command after it happend netstat -an|awk '/tcp/ {print $6}'|sort|uniq -c 109 CLOSE_WAIT 2652 ESTABLISHED 2 FIN_WAIT1 11 LAST_ACK 12 LISTEN 91 SYN_RECV 1 SYN_SENT 16 TIME_WAIT If i execute the same command some time later, i have something like this: 4 CLOSING 108 ESTABLISHED 18 FIN_WAIT1 182 FIN_WAIT2 37 LAST_ACK 12 LISTEN 50 SYN_RECV 11276 TIME_WAIT So in the normal situation i have only 100-200 open connections by clients beeing handled by apache in this moment. when i have this "crash", i have a lot more connections. what is the best way to analyse this? EDIT2: the important lines in apache2.conf are: KeepAlive On MaxKeepAliveRequests 20 KeepAliveTimeout 1 <IfModule mpm_prefork_module> ServerLimit 920 StartServers 30 MinSpareServers 80 MaxSpareServers 120 MaxClients 920 MaxRequestsPerChild 700 </IfModule> it is an apache2 prefork with php_mod. the server has 8GB ram and a 4gb swap partition.

    Read the article

  • How to Eliminate Tape Backup and Off-site Storage Service?

    - by Daniel Lucas
    PLEASE READ UPDATE AT THE BOTTOM. THANKS! ;) Environment Info (all Windows): 2 sites 30 servers site #1 (3TB of backup data) 5 servers site #2 (1TB of backup data) MPLS backbone tunnel connecting site #1 and site #2 Current Backup Process: Online Backup (disk-to-disk) Site #1 has a server running Symantec Backup Exec 12.5 with four 1TB USB 2.0 disks. BE jobs for full backups run nightly on all servers in site #1 to these disks. Site #2 backs up to a central file server there using software they already had when we purchased them. A BE job pulls that data nightly to site #1 and stores them on said disks. Off-site Backup (tape) Connected to our backup server is a tape drive. BE backs up the external disks to tape once a week which gets picked up by our off-site storage company. Obviously we rotate two tape libraries, one is always here and one is always there. Requirements: Eliminate the need for tape and off-site storage service by doing disk-to-disk at each site and replicating site #1 to site #2 and vice versa. Software based solution as hardware options have been too pricey (ie, SonicWall, Arkeia). Agents for Exchange, SharePoint, and SQL. Some Ideas So Far: Storage DroboPro at each site with an initial 8TB of storage (these are expandable up to 16TB at present). I like these because they are rackmountable, allow disparate drives, and have iSCSI interfaces. They are relatively cheap too. Software Symantec Backup Exec 12.5 already has all the agents and licenses we need. I'd like to keep using it unless there is a better solution, similarly priced, that does everything BE does plus deduplication and replication. Server Because there is no more need for a SCSI adapter (for tape drive) we are going to virtualize our backup server as it is currently the only physical machine save for SQL boxes. Problems: When replicating between sites we want as little data as possible to go across the pipe. There is no deduplication or compression in what I have laid out here so far. The files being replicated are BE's virtual tape libraries from our disk-to-disk backup. Because of this each of those huge files will go across the wire every week because they change every day. And Finally, the Question: Is there any software out there that does deduplication, or at least compression, to handle just our site-to-site replication? Or, looking at our setup, is there any other solution that I am missing that might be cheaper, faster, better? Thanks. Sorry so long. UPDATE 2: I've set a bounty on this question to get it more attention. I'm looking for software that will handle replication of data between two sites using the least amount of data possible (either compression, deduplication, or some other method). Something similar to rsync would work but it needs to be native to Windows and not a port involving shenanigans to get up and running. Prefer a GUI based product and I don't mind shelling out a few bones if it works. Please, answers that meet the above criteria only. If you don't think one exists or if you think I'm being to restrictive keep it to yourself. If after seven days there is no answer at all, so be it. Thanks again everyone. UPDATE 2: I really appreciate everyone coming forward with suggestions. There is no way for me to try all of these before the bounty expires. For now I'm going to let this bounty run out and whoever has the most votes will get the 100 rep points. Thanks again!

    Read the article

  • Proliant server will not accept new hard disks in RAID 1+0?

    - by Leigh
    I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

    Read the article

  • Amazon EC2 Instance - m1.medium Ubuntu 12.04 - Started to crash three days ago

    - by Joy
    The environment: Amazon EC2 Instance - m1.medium Ubuntu 12.04 Apache 2.2.22 - Running a Drupal Site Using MySQL DB Server RAM info: ~$ free -gt total used free shared buffers cached Mem: 3 1 2 0 0 0 -/+ buffers/cache: 0 2 Swap: 0 0 0 Total: 3 1 2 Hard drive info: Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 4.7G 2.9G 62% / udev 1.9G 8.0K 1.9G 1% /dev tmpfs 751M 180K 750M 1% /run none 5.0M 0 5.0M 0% /run/lock none 1.9G 0 1.9G 0% /run/shm /dev/xvdb 394G 199M 374G 1% /mnt The problem About two days ago the site started failing becaue the MySQL server was shut down by Apache with the following message: kernel: [2963685.664359] [31716] 106 31716 226946 22748 0 0 0 mysqld kernel: [2963685.664730] Out of memory: Kill process 31716 (mysqld) score 23 or sacrifice child kernel: [2963685.664764] Killed process 31716 (mysqld) total-vm:907784kB, anon-rss:90992kB, file-rss:0kB kernel: [2963686.153608] init: mysql main process (31716) killed by KILL signal kernel: [2963686.169294] init: mysql main process ended, respawning That states that the VM was occupying 0.9GB, but my Ram has 2GB free, so 1GB was still left free. I understand that in Linux applications can allocate more memory than physically available. I don't know if this is the problme, it's the first time that it has started to happen. Obviously, the MySQL server tries to restart, but there's no memory for it apparently and it won't restart. Here is its error log: Plugin 'FEDERATED' is disabled. The InnoDB memory heap is disabled Mutexes and rw_locks use GCC atomic builtins Compressed tables use zlib 1.2.3.4 Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 Completed initialization of buffer pool Fatal error: cannot allocate memory for the buffer pool Plugin 'InnoDB' init function returned error. Plugin 'InnoDB' registration as a STORAGE ENGINE failed. Unknown/unsupported storage engine: InnoDB [ERROR] Aborting [Note] /usr/sbin/mysqld: Shutdown complete I simply restarted the Mysql service. About two hours later it happened again. I restarted it. Then it happened again 9 hours later. So then I thought of the MaxClients parameter of apache.conf, so I went to check it out. It was set at 150. I decided to drop it down to 60. As so: <IfModule mpm_prefork_module> ... MaxClients 60 </IfModule> <IfModule mpm_worker_module> ... MaxClients 60 </IfModule> <IfModule mpm_event_module> ... MaxClients 60 </IfModule> Once I did that, I had the apache2 service restart and it all went smoothly for 3/4 of a day. Since at night the MySQL service shut down once again, but this time it wasn't killed by the Apache2 service. Instead it called the OOM-Killer with the following message: kernel: [3104680.005312] mysqld invoked oom-killer: gfp_mask=0x201da, order=0, oom_adj=0, oom_score_adj=0 kernel: [3104680.005351] [<ffffffff81119795>] oom_kill_process+0x85/0xb0 kernel: [3104680.548860] init: mysql main process (30821) killed by KILL signal Now I'm out of ideas. Some articles state that the ideal thing to do is change the kernel behaviour with the following (include it to the file /etc/sysctl.conf ) vm.overcommit_memory = 2 vm.overcommit_ratio = 80 So no overcommits will take place. I'm wondering if this is the way to go? Keep in mind I'm no server administrator, I have basic knowldege. Thanks a bunch in advance.

    Read the article

  • Hour-long shutdown duration "shutting down hyper-v virtual machine management service"

    - by icelava
    I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE Ok so i left it hanging over an hour while attending to other matters, and thankfully the host cleanly restarted. I can operate the guest machines fine now. Phew. Hyper-V must have been crawling for some reason. The VMs have been observed to become slow in the past when the host has been up for a long duration (two weeks to a month), but never this slow. Would love to know what types of performance monitoring items i can observe to give a hint why this can happen. UPDATE 2012-02-13 In the months ever since, Hyper-V has stalled into this state another two times. It appears so randomly and without any error event logs to hint what is causing it enter this "drunkard" state. Just an Hyper-V management service timeout. Log Name: System Source: Service Control Manager Date: 13/2/2012 9:16:48 AM Event ID: 7043 Task Category: None Level: Error Keywords: Classic User: N/A Computer: elune Description: The Hyper-V Virtual Machine Management service did not shut down properly after receiving a preshutdown control. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7043</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2012-02-13T01:16:48.882901900Z" /> <EventRecordID>567844</EventRecordID> <Correlation /> <Execution ProcessID="764" ThreadID="8484" /> <Channel>System</Channel> <Computer>elune</Computer> <Security /> </System> <EventData> <Data Name="param1">Hyper-V Virtual Machine Management</Data> </EventData> </Event> The only means out of it is to restart the system.

    Read the article

  • Tomcat and ASP site under IIS6 with SSL

    - by Rafe
    I've been working on migrating our companies' website from it's original server to a new one and am having two different but possibly related problems. The box this is sitting on is a Windows 2003 server x64 running IIS 6. The Tomcat version is 5.5.x as it was the version the original deployment was built on. There are two other sites on the server one in plain HTML, another in PHP and the one I am trying to migrate is a combination of Java and ASP (the introductory/sign in pages being Java as well as many reports used for our clients and the administration pages being in ASP) First of all I can only access the site if I enter the ip followed by :8080 (xxx.xxx.xxx.xxx:8080). The original setup had an index.html file in the root of the site with a bit of javascript in the header that pointed the site to 'www.mysite.com/app/public' but if I try going directly to the site without the 8080 I get a 'page not found error' and the javascript redirector causes the same problem because it doesn't add the 8080 into the URL even though on the original site the 8080 wasn't present so I don't understand why it would need it now. The js redirect looks like this: <script language="JavaScript"> <!-- location.href = "/app/public/" location.replace("/app/public/"); //--> </script> When setting the site up I used the command line to unbind IIS from all of the ip's on the system (there are 12 ip's on this box) because I was led to believe Tomcat wanted to use localhost which wasn't accessible. I'm not sure if this was the right thing to do but I'm throwing it in for the sake of completeness. And actually, at this point trying to go to localhost from the server itself throws up a 'could not connect to localhost' error. If I go to localhost:8080 I get the tomcat welcome page. If I do localhost:8080/app/public I get the intro page to our website. So I'm not sure what I'm even looking at in this case, that is what the proper behavior should be. The second part of the problem is that if I do go to either the ip or localhost such as above (localhost:8080/app/public) and click on our login link it is supposed to transfer me to our login page yet instead I receive a 'could not connect' error and the url has changed to localhost:8443/app/secure. From my research I see that port 8443 is Tomcats SSL port and the server.xml alludes to it as follows: <Connector port="8080" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" /> I have an SSL certificate assigned to the site via IIS and was under the impression that by default Tomcat allowed IIS to handle secure connections but apparently something is munged because it's not working. There is another section in the server.xml that reads like this: <Connector port="8009" enableLookups="false" redirectPort="443" protocol="AJP/1.3" /> Which I'm not sure what it is for although port 443 is the SSL port that IIS uses so I'm confused as to what this is supposed to be doing. Another question I have is when does the isap_redirector actually come into play? How does it know when to try and serve pages through Tomcat and when not to? I've hunted around the 'net for an answer and have yet to find a clear dialogue on the subject. Anyone have any pointers as to where to look for a solution to all of this?

    Read the article

  • vagrant fails to bring up additional adapter for centos vm using virtual box provider

    - by Anadi Misra
    this is in continuation of the question asked here about host only adapter on dhcp I upgraded to vagrant 1.6.3 and the updated Vagrantfile to following setting for multiple adapters # add additional adapter for inter machine networking dev.vm.network :private_network, :type => "dhcp", :adapter => "2", :netmask => "255.255.255.0" it goes through creating adapters but then fails bringing up the mic on vm Anadis-MacBook-Pro:full-stack-env anadi$ vagrant up Bringing machine 'full-stack-env' up with 'virtualbox' provider... ==> full-stack-env: Clearing any previously set forwarded ports... ==> full-stack-env: Clearing any previously set network interfaces... ==> full-stack-env: Preparing network interfaces based on configuration... full-stack-env: Adapter 1: nat full-stack-env: Adapter 2: hostonly ==> full-stack-env: Forwarding ports... full-stack-env: 22 => 4223 (adapter 1) full-stack-env: 8080 => 8090 (adapter 1) ==> full-stack-env: Running 'pre-boot' VM customizations... ==> full-stack-env: Booting VM... ==> full-stack-env: Waiting for machine to boot. This may take a few minutes... full-stack-env: SSH address: 127.0.0.1:4223 full-stack-env: SSH username: vagrant full-stack-env: SSH auth method: private key full-stack-env: Warning: Connection timeout. Retrying... full-stack-env: Warning: Connection timeout. Retrying... full-stack-env: Warning: Remote connection disconnect. Retrying... ==> full-stack-env: Machine booted and ready! ==> full-stack-env: Checking for guest additions in VM... ==> full-stack-env: Setting hostname... ==> full-stack-env: Configuring and enabling network interfaces... The following SSH command responded with a non-zero exit status. Vagrant assumes that this means the command failed! ARPCHECK=no /sbin/ifup eth 2> /dev/null Stdout from the command: Device eth does not seem to be present, delaying initialization. Stderr from the command: how ever when I log in to the environment I see two network interfaces as expected Anadis-MacBook-Pro:full-stack-env anadi$ vagrant ssh Last login: Wed Jun 4 12:54:47 2014 from 10.0.2.2 [vagrant@full-stack-env ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:BD:39:57 inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:febd:3957/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:511 errors:0 dropped:0 overruns:0 frame:0 TX packets:360 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54574 (53.2 KiB) TX bytes:46675 (45.5 KiB) eth1 Link encap:Ethernet HWaddr 08:00:27:A3:86:C9 inet addr:172.28.128.3 Bcast:172.28.128.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:86c9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1360 (1.3 KiB) TX bytes:894 (894.0 b) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) I am bit confused here on why it is trying to add another mic (eth2)? In the VM I used for creating this vagrant box, I had added two NICs already.

    Read the article

  • What NAS setup for syncing over the internet?

    - by Jamse
    I have family living a few hours away and have a lot of files that I would like to share - especially lots of folders of digital photos, but also documents etc. - partially so they can see them, partially so I can have access when I visit them and partially for backup / redundancy purposes. My current hard drives on my main machine are getting pretty full anyway, and I have a MythTV box where my music is currently stored, so I was thinking of getting a NAS anyway. And at the other end my family have a few computers, so they would probably benefit from a NAS too. My general idea (though I'm willing to shift on this if there are any bright ideas about other ways of achieving my objectives) is to get a matching pair of NASs and have them sync over the internet. (To cut down on bandwidth use I would get them in sync locally to start with.) Having read around as best I can it seems that syncing over the internet is generally only a feature on quite high end units. However, I have seen that QNAP seem to feature this on their TS-110 and TS-210 units, which might work (they call it "remote replication"). They seem pretty reasonably priced for what they are, but of course with buying 2 of them and then adding the drives (say 1TB or 2TB each) I'd be looking at about £400 total. So, I'm looking for recommendations really. I don't want to spend more than the QNAPs would cost me, but any other ideas would be most appreciated. I am comfortable with technology and tinkering around, but I don't have as much time for that as I would like, so I guess I would favour solutions that require less tinkering rather than more (even though that's less fun!). Any thoughts would be welcome, as would any comments from people who have used the QNAP boxes for this. Thanks in advance. Some specifications: Two-way syncing. Changes made at either end should be synced to the other. There shouldn't be one unit that is effectively a read-only mirror of the other. Not real time. The syncing doesn't need to be real time - if it updated, say, daily overnight that would be fine. Set and forget. I would prefer minimal user interaction once set up - it would be great if syncs were scheduled and automatic. OS independence. I am running Windows XP plus an Ubuntu-based MythTV box. At the other end there are Windows 7 and Windows XP machines, plus a networked TV set top box which I think can play files off the network. Machine independence. I would favour a system that is self-contained, i.e. not reliant on any particular PC being switched on. If the system had enough else going for it I could perhaps work around it at this end, where I only have one PC that's used as such, but it would be harder at the other where there are at least two PCs that might be accessing the files. Notifications. I guess things like getting an email notification if the syncing fell over for any reason would be useful, though it's not a deal breaker.

    Read the article

  • What seems to be plaguing my hard drives?

    - by Craig
    In a little bit of a tech nightmare here. I know oodles about software, not so much more than the above average user about hardware. I recently had to toss an old desktop of mine. It was gradually getting slower and slower, and after shutting the desktop down for long periods of time, it would choke up upon startup. Sometimes it'd give a disk read error, sometimes say no OS was found, etc. Restarting it about 5-15 times would eventually boot properly. Weird. I also noticed that startup programs were going missing, Dropbox was reindexing my entire folder, and Backblaze was backing up less than the number of files that it should. This lead me to believe it was probably a hard drive issue. I began to wonder why I'd have hard drive issues, and came to closure when I assumed it was because of recent power surges and outages. I'm sure that does a number on the drive. I bought a new desktop recently. It's not a beast or anything, but it's enough for what I do. It's an eMachines (I know, I know) Ultra-Slim (http://www.amazon.com/eMachines-Ultra-Slim-ER1401-57-Desktop-PC/dp/B00475OG9U). This is ideal for me because it's small and portable. It comes with an AC adapter and battery, like a laptop. Just to be safe, I bought an uninterruptable power supply on top of that. It's basically protected completely from any outages that might scramble the drive. I set this up a few days ago and for the past few days I've been perfecting settings, downloading the usual applications, etc. Two days ago, I noticed Dropbox was reindexing my entire Dropbox folder. I installed both Dropbox and Backblaze on this system, but it is very much more lightweight than the other. Only about 15 third-party applications installed. I thought that maybe Dropbox and Backblaze were stressing my system, so I turned off Backblaze. Still, Dropbox runs and comes across this infinite reindex issue. I noticed that upon a reboot recently, two applications did not start on startup either. Also, much like my old desktop, every 3rd or 4th reboot, I'll be forced into a chkdsk. This makes me incredibly nervous. What could possibly be going wrong with my old, years-old desktop that is immediately causing the same issues to my new one? I've considered all of the basics. I'm in a very air conditioned room. I take run routine virus scans. I'd like to think I take care of my systems very well. What is this issue that is haunting me? There's always the possibility that this new desktop has a junk hard drive, but it just seems way too coincidental.

    Read the article

  • What's wrong with this vcl config for varnish-cache as load balancer?

    - by dabito
    I have the current configurations active on my default.vcl varnish file on the machine that balances the load for other two machines (the other two machines also have varnish active). My intention is to have this server do only the load balancing and the other machines do the processing and also their own caching. My problem is that even with the config testing (not even a stress test or anything, just a few requests a minute) I get the guru meditation error and have to restart varnish. This is the default.vcl for the load balancing server: backend vader { .host = "app1.server.com"; .probe = { .url = "/"; .interval = 10s; .timeout = 4s; .window = 5; .threshold = 3; } } backend malgus { .host = "app2.server.com"; .probe = { .url = "/"; .interval = 10s; .timeout = 4s; .window = 5; .threshold = 3; } } director dooku round-robin { { .backend = vader; } { .backend = malgus; } } sub vcl_recv { if (req.http.host ~ "^balancer.server.com$") { set req.backend = dooku; } } Am I doing something wrong or missing something? EDIT: This is varnishlog's output: 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345839995 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345839998 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345840001 1.0 0 Backend_health - malgus Still sick 4--X--- 0 3 5 0.000000 3.846876 0 Backend_health - vader Still sick 4--X--- 0 3 5 0.000000 3.839194 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345840004 1.0 14 SessionOpen c 10.150.7.151 38272 :80 14 ReqStart c 10.150.7.151 38272 458200540 14 RxRequest c GET 14 RxURL c / 14 RxProtocol c HTTP/1.1 14 RxHeader c Host: dooku-dev.excelsior.com 14 RxHeader c Connection: keep-alive 14 RxHeader c User-Agent: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 14 RxHeader c Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 14 RxHeader c Accept-Encoding: gzip,deflate,sdch 14 RxHeader c Accept-Language: en-US,en;q=0.8,es-419;q=0.6,es;q=0.4 14 RxHeader c Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 14 RxHeader c Cookie: SESSa87d6c6da0c61037a9169122dc5e4a19=HR_0Srhgc-uDArT3aJFzOBy31FtzneTXg38byr1eGMU; __atuvc=4%7C33 14 VCL_call c recv pass 14 VCL_call c hash 14 Hash c / 14 Hash c dooku-dev.excelsior.com 14 VCL_return c hash 14 VCL_call c pass pass 14 FetchError c no backend connection 14 VCL_call c error deliver 14 VCL_call c deliver deliver 14 TxProtocol c HTTP/1.1 14 TxStatus c 503 14 TxResponse c Service Unavailable 14 TxHeader c Server: Varnish 14 TxHeader c Content-Type: text/html; charset=utf-8 14 TxHeader c Retry-After: 5 14 TxHeader c Content-Length: 418 14 TxHeader c Accept-Ranges: bytes 14 TxHeader c Date: Fri, 24 Aug 2012 20:26:44 GMT 14 TxHeader c X-Varnish: 458200540 14 TxHeader c Age: 0 14 TxHeader c Via: 1.1 varnish 14 TxHeader c Connection: close 14 Length c 418 14 ReqEnd c 458200540 1345840004.916415691 1345840004.965190172 0.020933390 0.048741817 0.000032663 14 SessionClose c error 14 StatSess c 10.150.7.151 38272 0 1 1 0 1 0 256 418 14 SessionOpen c 10.150.7.151 38273 :80 14 ReqStart c 10.150.7.151 38273 458200541 14 RxRequest c GET 14 RxURL c /favicon.ico 14 RxProtocol c HTTP/1.1 14 RxHeader c Host: dooku-dev.excelsior.com 14 RxHeader c Connection: keep-alive 14 RxHeader c Accept: */* 14 RxHeader c User-Agent: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 14 RxHeader c Accept-Encoding: gzip,deflate,sdch 14 RxHeader c Accept-Language: en-US,en;q=0.8,es-419;q=0.6,es;q=0.4 14 RxHeader c Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 14 RxHeader c Cookie: SESSa87d6c6da0c61037a9169122dc5e4a19=HR_0Srhgc-uDArT3aJFzOBy31FtzneTXg38byr1eGMU; __atuvc=4%7C33 14 VCL_call c recv pass 14 VCL_call c hash 14 Hash c /favicon.ico 14 Hash c dooku-dev.excelsior.com 14 VCL_return c hash 14 VCL_call c pass pass 14 FetchError c no backend connection 14 VCL_call c error deliver 14 VCL_call c deliver deliver 14 TxProtocol c HTTP/1.1 14 TxStatus c 503 14 TxResponse c Service Unavailable 14 TxHeader c Server: Varnish 14 TxHeader c Content-Type: text/html; charset=utf-8 14 TxHeader c Retry-After: 5 14 TxHeader c Content-Length: 418 14 TxHeader c Accept-Ranges: bytes 14 TxHeader c Date: Fri, 24 Aug 2012 20:26:45 GMT 14 TxHeader c X-Varnish: 458200541 14 TxHeader c Age: 0 14 TxHeader c Via: 1.1 varnish 14 TxHeader c Connection: close 14 Length c 418 14 ReqEnd c 458200541 1345840005.226389885 1345840005.226457834 0.000026941 0.000043154 0.000024796 14 SessionClose c error 14 StatSess c 10.150.7.151 38273 0 1 1 0 1 0 256 418

    Read the article

  • How to stop windows resizing when the monitor display channel is turned off / switched to different source

    - by Heartspeace
    Have a new 6870 ati radeon adapter with its drivers set to 1080p 60hz resolution hooked up to a 2008 47" high end Samsung HDMI based TV. However, when the tv is turned to a different hdmi input -(when I come back into windows) somehow Windows decides to resize all the open apps to a lower resolution - including some of the side docked hidden pop-outs. When it resizes those though - it just sticked the pop-outs in the middle of the screen and all the resized windows from the open applications in the top left corner - all of them stacked on top of each other and resized to the smaller resolution. The things that seem to be ok after returning are the icons on the desktop, the taskbar, and the sidebar. Anyone have any knowledge of 1) how this happens 2) why it happens 3) how to stop it from resizing the applications and some of the docked pop-outs (they are not really resized after returning - they are just stuck in the middle of the screen approximately where they would be if the right or bottom sidebar should be if the screen was resized to that lower resolution). My hypothesis is that upon losing HDMI signal - that Windows is told by something (driver, or windows itself) that the resolution to be without a signal being present (noting that HDMI signals and handshakes are two way on HDMI devices. If it loses the signal or the tv is switched to another device - then the display adapter must figure that out and tell Windows or figures it out and designs randomly to change the display size). Any and all help is most appreciated. I asked AMD/ATI - but they said they don't know why or how this is happening. I was hoping that maybe this is THE place that the super users truly go to - those that develop display adapter drivers, or that dive deeply into these areas of windows. If there is better sites or just competing sites - please advise - noting I have already written AMD/ATI. HP Response / Additions 4/7/2011 It is really nice to get your reply Shinrai. (BTW is it proper etiquette on these forums to have a discussion?) Yet 'only one issue' - I am using a single display in this case - so Windows doesn't move application windows to another desktop. Windows (or something) decides to shrink the desktop it currently has and resize all windows to the maximum size of the desktop. As such I would be glad if Windows would just keep the current size of the one desktop that is in operation. I also know that this does NOT happen on monitors connected with DVI. There I have had one and two monitors setup and it doesn't resize those screens at all when disconnecting monitors, turning them off, whatever... they stay solid - everything in place - to such an extent that if you forgot the other monitor is off - you will have troubles finding some windows without using one of the control app utilities. So if I could even get the HDMI handling by Windows (or the display driver) ( 1] which is doing this anyway the display driver or Windows - and 2] where is that other resolution size (1024x768) coming from - its not the smallest and its not the largest?) to be having like DVI - Life would be golden (for this aspect anyway). ** found others with same problem in this thread: http://hardforum.com/showthread.php?t=1507324 Thanks, HP

    Read the article

< Previous Page | 700 701 702 703 704 705 706 707 708 709 710 711  | Next Page >