Search Results

Search found 20264 results on 811 pages for 'home networking'.

Page 71/811 | < Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >

  • How to restart WiFi interface without rebooting (it drops connection)?

    - by Dima
    I boot into ubuntu and it connects to the Wifi network fine. After about 10-15min the DNS stop resolving any website and a couple of minutes later network-managers tells me that I'm disconnected and tries to reconnect constantly to my router and fails to do it. Upon Ubuntu restart everything works fine for the first 10-15min again. When I boot into Mac OS X everything is fine with the same connection! How do I restart wifi interface? sudo ifdow wlan0 just tells me that wlan0 is not configured and wlan0 doesn't appear in /etc/network/interfaces either, which I find strange.... (unless network-manager is doing it behind my back).

    Read the article

  • atheros ar8161 not recognized

    - by Paul
    Apparently I am not the only one with this problem. This was my solution, but it did not work, of course. I downloaded the tar from another computer. I found the file of the atheros driver that I needed which is apparently atl1c. I put that file on my ubuntu desktop. I ran the following in the terminal: cd ~/Desktop atl1c make sudo make install I am sure that some of you will find this code laughable, but isn't there a simple code I could use once I have the atl1c folder on the desktop?

    Read the article

  • How do I get my RTL8192ce based wireless device working properly?

    - by JonnyTruelove
    I am using the rtl8192cu chipset (on a Belkin wireless USB adapter N300) combined with 64 bit architecture and the 3.8 kernel. Some of you may know that this doesn't work. I tried this fix - RTL8188CU USB Network Adaptor on ubuntu 13.04 and now my internet is super slow. I am totally new to Ubuntu and I am concerned I do not have the right driver. The "stock" driver was the RTL8192cu, but it didn't connect 99% of the time and if it did the upload speed was higher than the download. Right now I am connecting through my laptop with a crossover cable, so my internet connection is just fine in my apartment. Relevant output from lsusb is here: Bus 002 Device 002: ID 050d:2103 Belkin Components F7D2102 802.11n N300 Micro Wireless Adapter v3000 [Realtek RTL8192CU] (bonus question: is that [050d:2103] the actual physical address straight from the hardware? Or does it change when I put different drivers on it? I am concerned I do not have the right driver)

    Read the article

  • How to resolve "Network host is busy; will retry in 30 seconds"?

    - by k0pernikus
    I have added a network printer, a Konica Minolta C253, via cups by its IP (http://10.0.0.42) under the http://localhost:631/ cups webfrontend on an Ubuntu 11.10 client. I used the documented KOC353U.ppd in the process. I was able to print exactly one page. Afterwards, all I get in the printer's status is the message: "Network host '10.0.0.42' is busy; will retry in 30 seconds". What is the problem here and how do I resolve it?

    Read the article

  • TCP port are filtered in VirtualBox

    - by iUngi
    I'm running Ubuntu using VirtualBox to test a server application, but I couldn't get it work the communication. I used nmap to check whether the port is open or not: nmap -T4 -n vbip -p 30000 Host is up (0.00061s latency). PORT STATE SERVICE 30000/tcp filtered unknown when I'm checking the port inside the VirtualBox, than the port is open Host is up (0.00061s latency). PORT STATE SERVICE 30000/tcp open unknown I'm using bridge connection, does the VB filter the ports?

    Read the article

  • Can't ping external websites

    - by Frantumn
    I can't ping google.com with my virtual ubuntu 12.04 server. I have set up a proxy URL in my /etc/apt/apt.conf file and it says Aquire::http::proxy http://urlname.com:9999; Now, I don't know a lot about how the proxy works, but I do know when we use it on windows VMachines it's a pac script that we place in internet explorer LAN settings and it automatically detects the script and gives internet access. I tried including the 9999/proxy.pac in the apt.conf URL and it didn't seem to work any better. Would ubuntu know how to handle a proxy.pac assuming it was created for windows? Should my URL include the .pac or just end after the port numbers? I've tried both without sucess, but I would like to know. A quick test to ping a fellow co-workers' PC was sucessful. So I can see network computers, but not google. or other internet sources.

    Read the article

  • When Ubuntu Server restarts eth0 Doesn't come back up

    - by JoelGsus
    Every time I restart my Ubuntu Server 11.10 I can't ssh into it because ETH0 doesn't come up automatically. I never had this problem before upgrading to 11.10. I have to login to the server and start the ETH0 manually. I would appreciate it any help. Thanks. Here is my /etc/networks/interfaces file: #The loopback network interface auto lo eth0 iface lo inet loopback # The primary network interface iface eth0 inet static address 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 network 192.168.1.0 gateway 192.168.1.1

    Read the article

  • IP/PORT forward requests to another server

    - by DT.DTDG
    I have the following listening PORT:IP set up on my UBuntu server. 12.345.67.890:3636 It receives requests perfectly, however, I would now like to forward any requests to that IP:PORT to another IP:PORT, i.e.: 09.876.54.321:3636 Essentially I want to do a request forward 12.345.67.890:3636 -> 09.876.54.321:3636. How can I go about it in Terminal and if I wanted to change it back how can I go about that too? Is there also a way to test that the data is forwarding and it is setup properly? Thanks! Edit: Can I just do as follows, just wondering how I would go about testing it and how I could disable it? sysctl net.ipv4.ip_forward=1 iptables -t nat -A PREROUTING -p tcp --dport 3636 -j DNAT --to-destination 09.876.54.321:3636 iptables -t nat -A POSTROUTING -j MASQUERADE

    Read the article

  • Is it illegal to forward copyrighted content? [closed]

    - by Mike
    Ok, this may be a strange question, but let's start: If I illegally download a movie (for example...) from a HTTP Web Server, there are many routers between me and the Web Server which are forwarding the data to my PC. As I understand, the owners of the routers are not legally responsible for the data they forward (please correct if I'm wrong). What if I would install a client of a peer-to-peer network on my PC and this client (peer) would forward copyrighted content received from peers to other peers? Hope someone understand what I mean ;-) Any answer or comment would be highly appreciated. Mike Update 1: I'm asking this question because I want to develop a p2p-application and try to figure out how to prevent illegal content sharing/distribution (if forwarding content is really illegal...) Update 2: What if the data forwarded by my peer is encrypted, so I'm technically not able to read and check it?

    Read the article

  • no wifi after grub 2 crash

    - by Omu
    on ubuntu 10.10 I used StartupManager to set windows 7 as the default boot, also chosen the 1024x768 resolution, 16 bit, time: 3sec, and checked "show splash screen". after the restart there was no GRUB menu at all, windows 7 booted, and in windows the clock was 0:03 instead of 10:03, also the wifi doesn't sees any connections anymore I reinstalled ubuntu 10.10 so the GRUB menu is back, changed the clock back from BIOS, but my wifi doesn't sees any connections in windows nor in ubuntu (I write this from another computer)

    Read the article

  • Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

    - by user42424
    So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

    Read the article

  • Ubuntu 12.04 Network Manager: unable to save manual setting to set up a static ip

    - by Andy
    I am fairly familiar with setting up servers, and ubuntu is generally my flavor of choice, but I just installed 12.04 desktop and I am seeing some behavior in network manager that is really puzzling. The network connection works fine if I leave it set on dhcp, but I would like a static IP address for my new web server. When I go into network manager and edit the connection for the one and only NIC I can select MANUAL from the dropdown menu but as soon as I do the Save button becomes greyed out. Even after filling out all fields for the connection it is still grey and I am unable to save the static IP connection information. Any thoughts would be greatly appreciated. I'm hoping there is just some new setting that I am unaware of.... On another note, if I stop the network manager and go edit the interfaces file (and the appropriate hosts/routes/dns files), I do get a static ip address assigned and I can contact my server from the outside, however, the server cannot find the internet. Can't ping even its own ip... I can ping the loopback interface though. I'm really confused on this one. Hoping someone can offer some help.

    Read the article

  • Uploading or attaching files that located on a shared drive doesn't work?

    - by Alex
    I have this odd, quite minor, but annoying issue that I am quite perplexed about. Whenever I try to upload a file via my browser(let's say attach a file to an email in GMail), I click 'Browse' button and it opens standard file selection dialog, that doesn't show network drives. Further more if I try to drag a file from a network drive into GMail, it doesn't work either, it just doesn't let me do that. This issue has been around for quite sometime now, and I am just curious if this is something on my side or if it's a bug or a misconfiguration of some sort. FWIW, I am currently running 10.10, network drive is a samba share on NAS. This happens in FF and Chrome and this is only happens with Samba mounts. As a matter of fact, NFS volumes that are located on the same network operate perfectly fine.

    Read the article

  • Intermittent internet connectivity

    - by Rob Oplawar
    UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

    Read the article

  • ubuntu nic card issue

    - by Blainer
    I am trying to install NIC r8168 and it shows everything installed ok. It is a brand new NIC and the lights wont come on when I plug in a ethernet. The NIC is that is not working is eth0. Why does it show the r8168 driver being used by 0? My NIC model number is ST1000SPEX if anyone is wondering. lsmod Module Size Used by r8168 215669 0 ifconfig eth0 Link encap:Ethernet HWaddr 00:0a:cd:1e:0a:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:19:d1:1d:f6:7a inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::219:d1ff:fe1d:f67a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:551467 errors:0 dropped:0 overruns:0 frame:0 TX packets:145219 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:409744342 (409.7 MB) TX bytes:12233173 (12.2 MB) Interrupt:21 Memory:dfde0000-dfe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:280 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22608 (22.6 KB) TX bytes:22608 (22.6 KB) Ubuntu 11.10 x64 Kernel 3.0.0-12-generic

    Read the article

  • UFW blocking random packets on 443

    - by s2jcpete
    All, I have UFW setup to allow traffic on port 443. It works as expected, though I have a large amount of UFW Block log entries. To Action From -- ------ ---- 80 ALLOW Anywhere 443 ALLOW Anywhere 22222 ALLOW Anywhere 80 ALLOW Anywhere (v6) 443 ALLOW Anywhere (v6) 22222 ALLOW Anywhere (v6) However in my syslog file I see this: [UFW BLOCK] IN=eth0 OUT= MAC=XXX SRC=<foreignip> DST=<serverip> LEN=40 TOS=0x00 PREC=0x00 TTL=116 ID=22025 DF PROTO=TCP SPT=49622 DPT=443 WINDOW=0 RES=0x00 ACK RST URGP=0 About 30 or so seconds later pound (which I'm using for SSL decryption and port redirection) throws a connection timed out messsage. I'm assuming this is because UFW is blocking the packet. I'm at a loss as to an explination. Could the packet be malformed or something, is this normal? Edit - I have since changed the /etc/defaults/ufw and set ipv6=no, so the v6 rules are no longer in the mix. The server is still showing the block / connection timed out behavior though. The new ufw status output is: Status: active Logging: on (low) Default: deny (incoming), allow (outgoing) New profiles: skip To Action From -- ------ ---- 80 ALLOW IN Anywhere 443 ALLOW IN Anywhere 22222 ALLOW IN Anywhere

    Read the article

  • Unstable Wifi and Spontaneous Low-graphic Error with Pavilion DV4

    - by Constant Dean
    I've been having numerous problems with connectivity through WiFi. It had been working for a few days and now it doesn't. On top of that around 40% of every time I turn on the laptop it shows "System running in low-graphics" error and I'm unable to view the desktop (sometimes not even able to access terminal), therefore having to manually power-down until it finally works. I use Ubuntu 12.10. nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: 84:34:97:6B:2E:D7 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.10 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 DNS: 68.237.161.12 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: rt2800pci State: unavailable Default: no HW Address: 68:94:23:50:A5:D9 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points

    Read the article

  • connecting ubuntu with 7 via network cable

    - by VeXe
    i was tryin to connect my ubuntu toshiba satalite L650 laptop with my desktop via a network cable so that i can share things and remotely control the desktop from the laptop, i googled the problem out and found a guide page , i followed all the steps , i installed samba, i had the two computer have the same workgroup name , i had everything correct, but i still dont see connection estbalished between the two computers, (neither one is visible to the other) what is missing ? thanx in advance.

    Read the article

  • Creating a new DHCP lease databse

    - by Stee1bear
    I have Ubuntu Server set up as my DCHP server. We have had it install for a few year and our dchp.lease file contain over 4000 entries. I am wanting to clean it up and basically start a new lease file to get current list (@1500 entries). I have read the walk through on how to make a new lease file and get it started, which leads me to this question. Will the dhcp server try to give each unit new IP address or will it build the new database with the IP addresses that the the units report to it?

    Read the article

  • Problems with No-IP redirecting

    - by user171156
    I am setting up a webserver on my ubuntu desktop 13.04, everything is working fine except; When trying to access the server through the external host using no-ip, it gives the original index created by apache on setup. While when I try to connect to the server via my real IP address from externally, it goes to the correct index. I have been trying to figure out what the issue is on this problem as nothing is working because of that bad redirect, I'm wondering if anyone of you could help me out, or advise me in the right path. Thank you very much! PS; If more info needed I'll provide, but this should explain it all.

    Read the article

  • Set up Trendnet TEW-638APB Access point on Ubuntu 14.04

    - by Mr. Smileys
    I have a computer running Ubuntu 14.04, it has 2 Ethernet ports. I would like to set up this computer so that the internet comes in on one of the ports and is then shared through the other port with the Trendnet wireless access point that my other devices would connect to and use the internet. I have looked online for information on setting this up but have not been able to find anything. If someone could point me to a guide that would help me or just tell me how to do this in an answer I would really appreciate it. please help me to solve this problem

    Read the article

  • Ubuntu Desktop on PC as an IPv6 router?

    - by Cliff
    I have a DELL PC with Ubuntu 12.10 and a pandaboard running the latest linaro ubuntu 12.08. The Ethernet on the panda board is reporting 'no ipv6 router present' regardless of what router I connect (they are all probably not ipv6). I can connect via a cross-over Ethernet cable the pandaboard to the DELL PC. Can I setup the DELL PC to act as an IPv6 router. the PC has a wireless connect to our router/ADSL box. I would Really appreciate some help here so if you have an alternative please suggest it.

    Read the article

  • audio and video data in RTP

    - by Banana
    Suppose a user wants to transmit both audio and video to another user, whose formats are AMR for audio and H.264 for video. Does the user have to transmit audio and video packets always separately? Meaning that it is not possible to mix audio and video within the same RTP packed, is that correct? If this is true I guess the RTP protocol will need to know the SSRC of both audio and video to be able to check the sync of the two streams.

    Read the article

  • How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

    - by user12285
    Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • How do I re-install Samba?

    - by Sheldon
    I recently followed a guide to configure Samba but I couldn't get it configured properly. After realizing that the guide was six years out of date I thought I should start again. I reinstalled samba by first using these commands: sudo apt-get purge samba sudo apt-get install samba But after reading my configuration file (/etc/samba/smb.conf) I noticed that it was the same file, containing the same edits I had made. I then proceeded to delete the directory and then re-install samba again. However, the directory is not replaced after re-instillation and now I don't appear to have a configuration file. How do I get it back? Or install Samba correctly?

    Read the article

< Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >