Search Results

Search found 18209 results on 729 pages for 'loop device'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 71/729 | < Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >

  • Getting a loop when using link_to :back

    - by onildo
    I have this structure for the table course: Search page - Result Page - Edit Page - Show page When i go from result page to a specific course edit page, i edit it, and end up on the show page, but when i hit back, i get a loop from show to edit, and back to show and so on. I want the edit page to back to the result page if it came from there. im using this on both: <%= link_to "Back", :back %>

    Read the article

  • Trimming lists using a loop

    - by Vishal
    I have few lists like: a = [1, 2, 3, 4, 5] b = [4, 6, 5, 9, 2] c = [4, 7, 9, 1, 2] I want to trim all of them using a loop, instead of doing as below: a[-2:] b[-2:] c[-2:] I tried but got confused with pass by value or pass by reference fundamentals, looked into other questions as well but no help. Thanks

    Read the article

  • Whats wrong with this while loop?

    - by David
    boolean r = false ; int s = 0 ; while (r == false) ; { s = getInt() ; if (!(s>=0 && s<=2)) System.out.println ("try again not a valid response") ; else r = true ; } The text never displays itself even when a 3 or a 123 is entered and the loop never terminates. Whats wrong here?

    Read the article

  • Issue with SPI (Serial Port Comm), stuck on ioctl()

    - by stef
    I'm trying to access a SPI sensor using the SPIDEV driver but my code gets stuck on IOCTL. I'm running embedded Linux on the SAM9X5EK (mounting AT91SAM9G25). The device is connected to SPI0. I enabled CONFIG_SPI_SPIDEV and CONFIG_SPI_ATMEL in menuconfig and added the proper code to the BSP file: static struct spi_board_info spidev_board_info[] { { .modalias = "spidev", .max_speed_hz = 1000000, .bus_num = 0, .chips_select = 0, .mode = SPI_MODE_3, }, ... }; spi_register_board_info(spidev_board_info, ARRAY_SIZE(spidev_board_info)); 1MHz is the maximum accepted by the sensor, I tried 500kHz but I get an error during Linux boot (too slow apparently). .bus_num and .chips_select should correct (I also tried all other combinations). SPI_MODE_3 I checked the datasheet for it. I get no error while booting and devices appear correctly as /dev/spidevX.X. I manage to open the file and obtain a valid file descriptor. I'm now trying to access the device with the following code (inspired by examples I found online). #define MY_SPIDEV_DELAY_USECS 100 // #define MY_SPIDEV_SPEED_HZ 1000000 #define MY_SPIDEV_BITS_PER_WORD 8 int spidevReadRegister(int fd, unsigned int num_out_bytes, unsigned char *out_buffer, unsigned int num_in_bytes, unsigned char *in_buffer) { struct spi_ioc_transfer mesg[2] = { {0}, }; uint8_t num_tr = 0; int ret; // Write data mesg[0].tx_buf = (unsigned long)out_buffer; mesg[0].rx_buf = (unsigned long)NULL; mesg[0].len = num_out_bytes; // mesg[0].delay_usecs = MY_SPIDEV_DELAY_USECS, // mesg[0].speed_hz = MY_SPIDEV_SPEED_HZ; mesg[0].bits_per_word = MY_SPIDEV_BITS_PER_WORD; mesg[0].cs_change = 0; num_tr++; // Read data mesg[1].tx_buf = (unsigned long)NULL; mesg[1].rx_buf = (unsigned long)in_buffer; mesg[1].len = num_in_bytes; // mesg[1].delay_usecs = MY_SPIDEV_DELAY_USECS, // mesg[1].speed_hz = MY_SPIDEV_SPEED_HZ; mesg[1].bits_per_word = MY_SPIDEV_BITS_PER_WORD; mesg[1].cs_change = 1; num_tr++; // Do the actual transmission if(num_tr > 0) { ret = ioctl(fd, SPI_IOC_MESSAGE(num_tr), mesg); if(ret == -1) { printf("Error: %d\n", errno); return -1; } } return 0; } Then I'm using this function: #define OPTICAL_SENSOR_ADDR "/dev/spidev0.0" ... int fd; fd = open(OPTICAL_SENSOR_ADDR, O_RDWR); if (fd<=0) { printf("Device not found\n"); exit(1); } uint8_t buffer1[1] = {0x3a}; uint8_t buffer2[1] = {0}; spidevReadRegister(fd, 1, buffer1, 1, buffer2); When I run it, the code get stuck on IOCTL! I did this way because, in order to read a register on the sensor, I need to send a byte with its address in it and then get the answer back without changing CS (however, when I tried using write() and read() functions, while learning, I got the same result, stuck on them). I'm aware that specifying .speed_hz causes a ENOPROTOOPT error on Atmel (I checked spidev.c) so I commented that part. Why does it get stuck? I though it can be as the device is created but it actually doesn't "feel" any hardware. As I wasn't sure if hardware SPI0 corresponded to bus_num 0 or 1, I tried both, but still no success (btw, which one is it?). UPDATE: I managed to have the SPI working! Half of it.. MOSI is transmitting the right data, but CLK doesn't start... any idea?

    Read the article

  • Loop through values and display in a pdf file

    - by chupinette
    Hello all! i have written the following code: As you can see there is a for loop to go through some values and display them in the generated pdf. The problem is that all the values are being written at the same place. I have tried to insert a new line but it does not seem to work. Can anyone suggest me how i can do it? Do i need to write a nested for loop so that it the values at different y positions? $pdf = pdf_new(); // open a file pdf_open_file($pdf, "C:/xampp/htdocs/final/6.pdf"); pdf_set_info($pdf, "Author", ""); pdf_set_info($pdf, "Title", ""); pdf_set_info($pdf, "Creator", ""); pdf_set_info($pdf, "Subject", ""); // start a new page (A4) $x = 595; $y = 842; pdf_begin_page($pdf, $x, $y); pdf_set_parameter($pdf, 'FontOutline', 'Arial=c:\windows\fonts\arial.ttf'); pdf_setcolor($pdf, "stroke", "rgb", 0, 0, 0, 1.0); // get and use a font object $font = pdf_findfont($pdf, "Arial", "host", 1); pdf_setfont($pdf, $font, 10); // print text pdf_show_xy($pdf, "QUOTATION" , 250, $y - 60); pdf_show_xy($pdf, "Customer Name: " . $this->customer_details['first_name'] . " " . $this->customer_details['last_name'], 50, 770); pdf_show_xy($pdf, "Date: " . date("F j, Y, g:i a"), 50, 750); pdf_show_xy($pdf, "Number of items requested: " . $count_items_req, 50, 730); pdf_show_xy($pdf, "Number of items found: " . $count_items_found, 50, 710); // add an image under the text $image = $image = PDF_load_image($pdf, "png", "C:/xampp/htdocs/final/images/footer_logo.png", ""); PDF_fit_image($pdf, $image, 50, 785, ""); pdf_moveto($pdf, 20, 780); pdf_lineto($pdf, 575, 780); pdf_stroke($pdf); // draw another line near the bottom of the page pdf_moveto($pdf, 20, 50); pdf_lineto($pdf, 575, 50); pdf_stroke($pdf); //Draw the lines $offset = 184; $i = 0; pdf_moveto($pdf, 20, $y - 160); pdf_lineto($pdf, $x - 20, $y - 160); pdf_stroke($pdf); pdf_moveto($pdf, $x - 400, $y - 160); pdf_lineto($pdf, $x - 400, 80); pdf_stroke($pdf); pdf_moveto($pdf, $x - 200, $y - 160); pdf_lineto($pdf, $x - 200, 80); pdf_stroke($pdf); pdf_moveto($pdf, $x - 100, $y - 160); pdf_lineto($pdf, $x - 100, 80); pdf_stroke($pdf); pdf_continue_text($pdf, ''); pdf_continue_text($pdf, ''); pdf_show_xy($pdf, "Searched Item", 70, $y - 150); pdf_show_xy($pdf, "Searched Item", 70, $y - 150); pdf_show_xy($pdf, "Item name", 240, $y - 150); pdf_show_xy($pdf, "Item name", 240, $y - 150); pdf_show_xy($pdf, "Price", $x - 180, $y - 150); pdf_show_xy($pdf, "Price", $x - 180, $y - 150); pdf_show_xy($pdf, "Discounted Price", $x - 100, $y - 150); pdf_show_xy($pdf, "Discounted Price", $x - 100, $y - 150); for ($i = 0; $i < count($this->quotation_details); $i++) { pdf_show_xy($pdf, $this->quotation_details[$i]['name_searched'] , 70, $y - 500); } // and write some text under it pdf_show_xy($pdf, "", 250, 35); // end page pdf_end_page($pdf); // close and save file pdf_close($pdf);

    Read the article

  • Issue in Creating an Insert Query See Description Below...

    - by Parth
    I am creating a Insert Query using PHP.. By fetching the data from a Audit table and iterating the values of it in loops.. table from which I am fetching the value has the snapshot below: The Code I am using to create is given below: mysql_select_db('information_schema'); $select = mysql_query("SELECT TABLE_NAME FROM TABLES WHERE TABLE_SCHEMA = 'pranav_test'"); $selectclumn = mysql_query("SELECT * FROM COLUMNS WHERE TABLE_SCHEMA = 'pranav_test'"); mysql_select_db('pranav_test'); $seletaudit = mysql_query("SELECT * FROM jos_audittrail WHERE live = 0"); $tables = array(); $i = 0; while($row = mysql_fetch_array($select)) { $tables[$i++] =$row['TABLE_NAME']; } while($row2 = mysql_fetch_array($seletaudit)) { $audit[] =$row2; } foreach($audit as $val) { if($val['operation'] == "INSERT") { if(in_array($val['table_name'],$tables)) { $insert = "INSERT INTO '".$val['table_name']."' ("; $selfld = mysql_query("SELECT field FROM jos_audittrail WHERE table_name = '".$val['table_name']."' AND operation = 'INSERT' AND trackid = '".$val['trackid']."'"); while($row3 = mysql_fetch_array($selfld)) { $values[] = $row3; } foreach($values as $field) { $insert .= "'".$field['field']."', "; } $insert .= "]"; $insert = str_replace(", ]",")",$insert); $insert .= " values ("; $selval = mysql_query("SELECT newvalue FROM jos_audittrail WHERE table_name = '".$val['table_name']."' AND operation = 'INSERT' AND trackid = '".$val['trackid']."' AND live = 0"); while($row4 = mysql_fetch_array($selval)) { $value[] = $row4; } /*echo "<pre>"; print_r($value);exit;*/ foreach($value as $data) { $insert .= "'".$data['newvalue']."', "; } $insert .= "["; $insert = str_replace(", [",")",$insert); } } } When I Echo the $insert out of the most outer for loop (for auditrail) The values get printed as many times as the records are found for the outer for loop..i.e 'orderby= show_noauth= show_title= link_titles= show_intro= show_section= link_section= show_category= link_category= show_author= show_create_date= show_modify_date= show_item_navigation= show_readmore= show_vote= show_icons= show_pdf_icon= show_print_icon= show_email_icon= show_hits= feed_summary= page_title= show_page_title=1 pageclass_sfx= menu_image=-1 secure=0 ', '0000-00-00 00:00:00', '13', '20', '1', '152', 'accmenu', 'IPL', 'ipl', 'index.php?option=com_content&view=archive', 'component' gets repeated , i.e. INSERT INTO 'jos_menu' ('params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type', 'params', 'checked_out_time', 'ordering', 'componentid', 'published', 'id', 'menutype', 'name', 'alias', 'link', 'type') values ('orderby= show_noauth= show_title= link_titles= show_intro= show_section= link_section= show_category= link_category= show_author= show_create_date= show_modify_date= show_item_navigation= show_readmore= show_vote= show_icons= show_pdf_icon= show_print_icon= show_email_icon= show_hits= feed_summary= page_title= show_page_title=1 pageclass_sfx= menu_image=-1 secure=0 ', '0000-00-00 00:00:00', '13', '20', '1', '152', 'accmenu', 'IPL', 'ipl', 'index.php?option=com_content&view=archive', 'component', 'orderby= show_noauth= show_title= link_titles= show_intro= show_section= link_section= show_category= link_category= show_author= show_create_date= show_modify_date= show_item_navigation= show_readmore= show_vote= show_icons= show_pdf_icon= show_print_icon= show_email_icon= show_hits= feed_summary= page_title= show_page_title=1 pageclass_sfx= menu_image=-1 secure=0 ', '0000-00-00 00:00:00', '13', '20', '1', '152', 'accmenu', 'IPL', 'ipl', 'index.php?option=com_content&view=archive', 'component', 'orderby= show_noauth= .. .. .. .. and so on What I want is I should get these Values for once, I know there is mistake using the outer Forloop, but I m not getting the idea of rectifying it.. Please help... please poke me for more clarification...

    Read the article

  • Form loop db insertion + javascript altering

    - by MrStatic
    I basically need to check if there is an easier way to do this before I rewrite all the code. I have a fairly large form that I have each input named with []'s on the end so I can loop through via php for easy insertion. <input type="hidden" name="currentdate[]" value="<?php echo date('mdY'); ?>"> <td><input style="width: 50px" type="text" name="jackname[]" /></td> <td><input style="width: 20px" type="text" name="jackkey[]" /></td> <td><input style="width: 50px" type="text" name="jackbeg[]" /></td> <td><input style="width: 50px" type="text" name="jackend[]" /></td> <td><input style="width: 50px" type="text" name="jackbegveh" /></td> <td><input style="width: 50px" type="text" name="jackbegmon[]" /></td> <td><input style="width: 50px" type="text" name="jackendveh" /></td> <td><input style="width: 50px" type="text" name="jackendmon[]" /></td> <td><input style="width: 50px" type="text" name="jacktx" disabled /></td> There are quite a few more fields but you get the idea. I then use foreach ($_POST['jackname'] as $row=>$name) { $jackname = $name; $date = $_POST['currentdate'][$row]; $jackkey = $_POST['jackkey'][$row]; $jackbeg = $_POST['jackbeg'][$row]; $jackend = $_POST['jackend'][$row]; $jackbegveh = $_POST['jackbegveh'][$row]; $jackbegmon = $_POST['jackbegmon'][$row]; $jackendveh = $_POST['jackendveh'][$row]; $jackendmon = $_POST['jackendmon'][$row]; $jacktx = $_POST['jacktx'][$row]; if ($jacktx == '') { $jacktx = '0'; } if (empty($jackkey)) { echo 'Skipped empty! <br />'; } else { mysql_query("INSERT INTO `ticket_counts_jackson` VALUES('', '" . $date . "', '" . $jackname . "', '" . $jackkey . "', '" . $jackbeg . "', '" . $jackend . "', '" . $jackbegveh . "', '" . $jackbegmon . "', '" . $jackendveh . "', '" . $jackendmon . "', '" . $jacktx . "')", $mysql_link) or die(mysql_error()); echo 'Added the info the db! <br />'; } } I use the above to loop through the form and add it to the database. Now for my main question. I also want to add in some javascript to do a little math. Basically ($jackendveh - $jackbegveh) - ($jackendmon - $jackbegmon) and have that displayed in jacktx. Currently the only way I know of adding in the math calculations is to rename each input to a unique name and then rewrite my insert from 1 insert to 8 inserts.

    Read the article

  • PHP and XPath Loop

    - by user1794852
    Thank you all in advance. I've got some great answers to my sometimes stupid questions, so thank you again. I'm trying to parse a SOAP response using PHP, Xpath (namespaces) and SimpleXML. Down below is a snippet of the Response. What I need to do is loop through each <ns1:file></ns1:file> and add it to a DB. But I'm not sure how to do that. Please help! Namespace Stuff $x = simplexml_load_string($response); $x->registerXPathNamespace('ns1', 'http://ws.icontent.idefense.com/V3/2'); Here's the response: <ns1:mal_files> <ns1:file> <ns1:id>2895144</ns1:id> <ns1:md5>2189c3d3857ba0cabd19c8aa031d63cd</ns1:md5> <ns1:sha1>c20b26148caa059ecf85e9b29df4e28e8354d655</ns1:sha1> <ns1:path>%WINDIR%\Temp\Temporary Internet Files\Content.IE5\K9ANOPQB\1219831[1].htm</ns1:path> <ns1:size>110</ns1:size> <ns1:code_available>true</ns1:code_available> <ns1:len_char>fixed</ns1:len_char> </ns1:file> <ns1:file> <ns1:id>2895147</ns1:id> <ns1:md5>a533825ef1752630a300125b3eef6825</ns1:md5> <ns1:sha1>ec7feb1414b3c2e720f6c06e2750421b73634f87</ns1:sha1> <ns1:path>%WINDIR%\Temp\Temporary Internet Files\Content.IE5\4PMB8T67\bg[1].jpg</ns1:path> <ns1:size>707</ns1:size> <ns1:code_available>true</ns1:code_available> <ns1:len_char>fixed</ns1:len_char> </ns1:file> <ns1:file> <ns1:id>2895155</ns1:id> <ns1:md5>c88724e985efcc82173c0d3aa0b77dfd</ns1:md5> <ns1:sha1>ecc042ca06aac988cd4593bb2b25fa39c4b2a819</ns1:sha1> <ns1:path>%WINDIR%\Prefetch\24604775.EXE-3ADEC0C2.pf</ns1:path> <ns1:size>44940</ns1:size> <ns1:code_available>true</ns1:code_available> <ns1:len_char>fixed</ns1:len_char> </ns1:file> <ns1:file> <ns1:id>2895158</ns1:id> <ns1:md5>422a011793af6195ea517c2c4a26bdbc</ns1:md5> <ns1:sha1>f449240c091c27e2531342d6b291d6a7e4655834</ns1:sha1> <ns1:path>%WINDIR%\Temp\Temporary Internet Files\Content.IE5\KPYV0TM7\gamesleap[1].png</ns1:path> <ns1:size>2676</ns1:size> <ns1:code_available>true</ns1:code_available> <ns1:len_char>fixed</ns1:len_char> </ns1:file> </ns1:mal_files> PHP Code $md5 = $x->xpath('//ns1:mal_files/ns1:file/ns1:md5'); // Returns array :( The PHP code returns an Array of all MD5 for every <ns1:file></ns1:file> and that's not what I need. What I need is to loop through each of the (nodes?) for each of the <ns1:file> keying on the <ns1:id> and add all their associated elements (id, md5, sha1, etc) as a record, then move onto the next <ns1:file> and repeat. And obviously the PHP I'm using returns an array, which doesn't work here. Hopefully I've made my question clear... I appreciate any help. Thanks!

    Read the article

  • Dual Boot issues with Windows 7 and Ubuntu

    - by Michael
    I'm finding myself in a rather unique situation. I've read through just about every resource I can find about this and while things have helped me understand some background, I haven't yet been able to find a solution. So I'm asking here. I originally had just a Windows 7 64-bit OS installation on my desktop. Learning that I couldn't do anything with Apache, PHP and MySql from within a 64-bit system, I did some research and found out that I could use Ubuntu. I've installed the latest version: 11.04. I created a CD to install Ubuntu from and the install went just fine. I installed it side-by-side with Windows 7. I can boot into Ubuntu just fine through the dual-boot option. When I reboot to load Windows though, the Grub2 list shows Windows 7 (loader) and when I select this option the Windows System Recovery loads instead of the actual OS. I haven't made it past there because I didn't know what to do. I just shut the computer down and rebooted into Ubuntu. I've been working for the last hour and a half to try to figure out how to boot into the Windows 7 OS and I haven't got a clue. While I'm somewhat proficient with Windows 7, I'm totally new to Ubuntu, so if you do know what needs to happen, please keep it simple enough that I'll be able to understand. Thanks for all your help in advance. Here's the results after using the Boot Info Script: Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #5 for cbh. => Windows is installed in the MBR of /dev/sdb => Grub 2 is installed in the MBR of /dev/mapper/pdc_bdadcfbdif and looks on the same drive in partition #5 for cbh. sda1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sda2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sda3: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy sdb1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /Boot/BCD sdb2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb3: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /boot/BCD sdb4: _________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb6: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: pdc_bdadcfbdif1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: /bootmgr /Boot/BCD pdc_bdadcfbdif2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files/dirs: /bootmgr /Boot/BCD /Windows/System32/winload.exe pdc_bdadcfbdif3: _________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy fuse: mount failed: Device or resource busy mount: unknown filesystem type '' =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sda1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/sda2 206,911 1,440,372,735 1,440,165,825 7 HPFS/NTFS /dev/sda3 1,440,372,736 1,464,856,575 24,483,840 7 HPFS/NTFS Drive: sdb ___________________ _____________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sdb1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/sdb2 206,911 1,342,554,688 1,342,347,778 7 HPFS/NTFS /dev/sdb3 1,930,344,448 1,953,521,663 23,177,216 7 HPFS/NTFS /dev/sdb4 1,342,556,158 1,930,344,447 587,788,290 5 Extended /dev/sdb5 1,342,556,160 1,896,806,399 554,250,240 83 Linux /dev/sdb6 1,896,808,448 1,930,344,447 33,536,000 82 Linux swap / Solaris Drive: pdc_bdadcfbdif ___________________ _____________________________________________________ Disk /dev/mapper/pdc_bdadcfbdif: 750.0 GB, 749999947776 bytes 255 heads, 63 sectors/track, 91182 cylinders, total 1464843648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/mapper/pdc_bdadcfbdif1 * 2,048 206,847 204,800 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif2 206,911 1,440,372,735 1,440,165,825 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif3 1,440,372,736 1,464,856,575 24,483,840 7 HPFS/NTFS /dev/mapper/pdc_bdadcfbdif3 ends after the last sector of /dev/mapper/pdc_bdadcfbdif blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/mapper/pdc_bdadcfbdif1 888E54CC8E54B482 ntfs SYSTEM /dev/mapper/pdc_bdadcfbdif2 C2766BF6766BEA1D ntfs OS /dev/mapper/pdc_bdadcfbdif: PTTYPE="dos" /dev/sda1 888E54CC8E54B482 ntfs SYSTEM /dev/sda2 C2766BF6766BEA1D ntfs OS /dev/sda3 BE6CA31D6CA2CF87 ntfs HP_RECOVERY /dev/sda promise_fasttrack_raid_member /dev/sdb1 20B65685B6565B7C ntfs SYSTEM /dev/sdb2 B4467A314679F508 ntfs HP /dev/sdb3 6E10B7A410B77227 ntfs FACTORY_IMAGE /dev/sdb4: PTTYPE="dos" /dev/sdb5 266f9801-cf4f-4acc-affa-2092be035f0c ext4 /dev/sdb6 1df35749-a887-45ff-a3de-edd52239847d swap /dev/sdb: PTTYPE="dos" error: /dev/mapper/pdc_bdadcfbdif3: No such file or directory error: /dev/sdc: No medium found error: /dev/sdd: No medium found error: /dev/sde: No medium found error: /dev/sdf: No medium found error: /dev/sdg: No medium found ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sdb5 / ext4 (rw,errors=remount-ro,commit=0) =========================== sdb5/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux /boot/vmlinuz-2.6.38-8-generic-pae root=UUID=266f9801-cf4f-4acc- affa-2092be035f0c ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.38-8-generic-pae } menuentry 'Ubuntu, with Linux 2.6.38-8-generic-pae (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c echo 'Loading Linux 2.6.38-8-generic-pae ...' linux /boot/vmlinuz-2.6.38-8-generic-pae root=UUID=266f9801-cf4f-4acc-affa-2092be035f0c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.38-8-generic-pae } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/sdb,msdos5)' search --no-floppy --fs-uuid --set=root 266f9801-cf4f-4acc-affa-2092be035f0c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sdb1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(/dev/sdb,msdos1)' search --no-floppy --fs-uuid --set=root 20B65685B6565B7C chainloader +1 } menuentry "Windows Recovery Environment (loader) (on /dev/sdb3)" --class windows --class os { insmod part_msdos insmod ntfs set root='(/dev/sdb,msdos3)' search --no-floppy --fs-uuid --set=root 6E10B7A410B77227 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sdb5/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sdb5 during installation UUID=266f9801-cf4f-4acc-affa-2092be035f0c / ext4 errors=remount-ro 0 1 # swap was on /dev/sdb6 during installation UUID=1df35749-a887-45ff-a3de-edd52239847d none swap sw 0 0 =================== sdb5: Location of files loaded by Grub: =================== 900.1GB: boot/grub/core.img 825.0GB: boot/grub/grub.cfg 688.7GB: boot/initrd.img-2.6.38-8-generic-pae 688.0GB: boot/vmlinuz-2.6.38-8-generic-pae 688.7GB: initrd.img 688.0GB: vmlinuz =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on pdc_bdadcfbdif3 =======Devices which don't seem to have a corresponding hard drive============== sdc sdd sde sdf sdg =============================== StdErr Messages: =============================== ERROR: dos: partition address past end of RAID device hexdump: /dev/mapper/pdc_bdadcfbdif3: No such file or directory hexdump: /dev/mapper/pdc_bdadcfbdif3: No such file or directory ERROR: dos: partition address past end of RAID device

    Read the article

  • Wireless will not connect

    - by azz0r
    Hello, I have installed Ubuntu 10.10 on the same machine as my windows setup. However, it will not connect to my wireless network. It can see its there, it can attempt to connect, yet it will never connect. It will keep bringing up the password prompt everyso often. I have tried turning my security to WEP, I ended up turning it back to WPA2. It is set to AES (noted a few threads on google about that). Can you assist? I would love to dive into Ubuntu, but without the internet its pointless. --- lshw -C network --- *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 00:1d:92:ea:cc:62 capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8168 driverversion=8.020.00-NAPI duplex=half latency=0 link=no multicast=yes port=twisted pair resources: irq:29 ioport:e800(size=256) memory:feaff000-feafffff memory:f8ff0000-f8ffffff(prefetchable) memory:feac0000-feadffff(prefetchable) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:15:af:72:a4:38 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bgn --- iwconfig ---- lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Wuggawoo" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Tx-Power=9 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on --- cat /etc/network/interfaces ---- auto lo iface lo inet loopback logs deamon.log --- Jan 19 04:17:09 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:09 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:11 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:11 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): association took too long. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 5 -> 6 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): asking for new secrets Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 6 -> 4 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): device state change: 4 -> 5 (reason 0) Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0/wireless): connection 'Wuggawoo' has security, and secrets exist. No new secrets needed. Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'ssid' value 'Wuggawoo' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'scan_ssid' value '1' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'key_mgmt' value 'WPA-PSK' Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: added 'psk' value '<omitted>' Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_engine_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: nm_setting_802_1x_get_pkcs11_module_path: assertion `NM_IS_SETTING_802_1X (setting)' failed Jan 19 04:17:12 ubuntu NetworkManager: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:12 ubuntu NetworkManager: <info> Config: set interface ap_scan to 1 Jan 19 04:17:12 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:13 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:13 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:23 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:17:23 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:17:24 ubuntu AptDaemon: INFO: Initializing daemon Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:17:25 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:17:25 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:17:27 ubuntu NetworkManager: <info> wlan0: link timed out. --- kern.log --- Jan 19 04:18:11 ubuntu kernel: [ 142.420024] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:13 ubuntu kernel: [ 144.333847] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:13 ubuntu kernel: [ 144.539996] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:13 ubuntu kernel: [ 144.750027] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:14 ubuntu kernel: [ 144.940022] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out Jan 19 04:18:25 ubuntu kernel: [ 155.832995] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:25 ubuntu kernel: [ 156.030046] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:25 ubuntu kernel: [ 156.230039] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:25 ubuntu kernel: [ 156.430039] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out --- syslog --- Jan 19 04:18:46 ubuntu wpa_supplicant[1289]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 04:18:46 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: WPS-AP-AVAILABLE Jan 19 04:18:48 ubuntu wpa_supplicant[1289]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 04:18:48 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 04:18:48 ubuntu kernel: [ 178.833905] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 1) Jan 19 04:18:48 ubuntu kernel: [ 179.030035] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 2) Jan 19 04:18:48 ubuntu kernel: [ 179.230020] wlan0: direct probe to AP 94:44:52:0d:22:0d (try 3) Jan 19 04:18:48 ubuntu kernel: [ 179.433634] wlan0: direct probe to AP 94:44:52:0d:22:0d timed out lspci and lsusb lspci -- 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:12.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller 00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller 00:13.2 USB Controller: ATI Technologies Inc SB700/SB800 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a) 00:14.1 IDE interface: ATI Technologies Inc SB700/SB800 IDE Controller 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB700/SB800 LPC host controller 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:14.5 USB Controller: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 01:00.0 VGA compatible controller: nVidia Corporation G80 [GeForce 8800 GTS] (rev a2) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 03:00.0 FireWire (IEEE 1394): JMicron Technology Corp. IEEE 1394 Host Controller -- lsusb -- Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 004 Device 002: ID 045e:0730 Microsoft Corp. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 003: ID 13d3:3247 IMC Networks 802.11 n/g/b Wireless LAN Adapter Bus 002 Device 002: ID 0718:0628 Imation Corp. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 046d:08c2 Logitech, Inc. QuickCam PTZ Bus 001 Device 002: ID 0424:2228 Standard Microsystems Corp. 9-in-2 Card Reader Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub With no security on my router I still can't connect, I get: Jan 19 15:58:01 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:01 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: disconnected -> scanning Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: WPS-AP-AVAILABLE Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Trying to associate with 94:44:52:0d:22:0d (SSID='Wuggawoo' freq=2437 MHz) Jan 19 15:58:02 ubuntu wpa_supplicant[1165]: Association request to the driver failed Jan 19 15:58:02 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: scanning -> associating Jan 19 15:58:05 ubuntu NetworkManager: <info> wlan0: link timed out. Jan 19 15:58:07 ubuntu wpa_supplicant[1165]: Authentication with 94:44:52:0d:22:0d timed out. Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connection state: associating -> disconnected Jan 19 15:58:07 ubuntu NetworkManager: <info> (wlan0): supplicant connec

    Read the article

  • How do I make my USB Bluetooth dongle work in Ubuntu 11.04 ? (Can't init device hci0: Connection timed out (110)) [closed]

    - by MaikoID
    I've a USB bluetooth dongle root@maiko-cce-lin:~# lsusb | grep Bluetooth Bus 001 Device 007: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) that isn't working properly, hardly-ever it works but stops working in my next reboot. what I've tried it isn't software blocked root@maiko-cce-lin:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hci0: Bluetooth Soft blocked: no Hard blocked: no my device is recognized by hciconfig root@maiko-cce-lin:~# hciconfig -a hci0: Type: BR/EDR Bus: USB BD Address: 00:1F:81:00:01:1C ACL MTU: 1021:4 SCO MTU: 180:1 DOWN RX bytes:330 acl:0 sco:0 events:8 errors:0 TX bytes:24 acl:0 sco:0 commands:30 errors:22 Features: 0xff 0x3e 0x09 0x76 0x80 0x01 0x00 0x80 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: Link mode: SLAVE ACCEPT but I can't turn on my hci interface root@maiko-cce-lin:~# hciconfig hci up Can't init device hci0: Connection timed out (110) I don't understand why.. the hcitool command doesn't show any device. root@maiko-cce-lin:~# hcitool dev Devices: I've tried to restart my bluetooth service too with this command and make all these previous commands again but without success. root@maiko-cce-lin:~# service bluetooth restart * Stopping bluetooth [ OK ] * Starting bluetooth [ OK ] root@maiko-cce-lin:~# The dongle works if you disconnect it from usb, wait a few seconds and connect it again. so there must be better solution for it ( a solution not involving physically removing the dongle!)

    Read the article

  • Why Wifi no longer works 12.04.1

    - by Roger
    starting this morning over wifi (Realtek RTL8188CE) on CLEVO W253HU. May be due to the update before yesterday, more pilot managed, but somehow it worked yesterday. If someone has an idea of the problem. Back command lines: cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 006: ID 192f:0416 Avago Technologies, Pte. Bus 002 Device 004: ID 5986:0315 Acer, Inc lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) lspci -nn | grep -i net 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 03:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) lspci -k 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: i2c-i801 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device 9196 Kernel modules: rtl8192ce 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jme Kernel modules: jme 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: sdhci-pci 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jmb38x_ms Kernel modules: jmb38x_ms sudo lshw -C network *-network NON-RÉCLAMÉ description: Network controller produit: RTL8188CE 802.11b/g/n WiFi Adapter fabriquant: Realtek Semiconductor Co., Ltd. identifiant matériel: 0 information bus: pci@0000:02:00.0 version: 01 bits: 64 bits horloge: 33MHz fonctionnalités: pm msi pciexpress cap_list configuration: latency=0 ressources: portE/S:e000(taille=256) mémoire:f7d00000-f7d03fff *-network description: Ethernet interface produit: JMC250 PCI Express Gigabit Ethernet Controller fabriquant: JMicron Technology Corp. identifiant matériel: 0 information bus: pci@0000:03:00.0 nom logique: eth0 version: 05 numéro de série: 00:90:f5:c1:c6:45 taille: 100Mbit/s capacité: 1Gbit/s bits: 32 bits horloge: 33MHz fonctionnalités: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=full ip=192.168.1.54 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s ressources: irq:44 mémoire:f7c20000-f7c23fff portE/S:d100(taille=128) portE/S:d000(taille=256) mémoire:f7c10000-f7c1ffff mémoire:f7c00000-f7c0ffff lsmod Module Size Used by btusb 18288 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 11 btusb,rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 binfmt_misc 17540 1 snd_hda_codec_realtek 224173 0 dm_crypt 23125 0 snd_hda_codec_hdmi 32474 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_hda_intel 33773 2 snd_hda_codec 127706 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi jmb38x_ms 17646 0 psmouse 87692 0 serio_raw 13211 0 memstick 16569 1 jmb38x_ms snd_seq_midi_event 14899 1 snd_seq_midi rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi mac_hid 13253 0 snd 78855 14 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 205544 2 rtlwifi,mac80211 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid i915 473035 3 drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper jme 41259 0 i2c_algo_bit 13423 1 i915 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci wmi 19256 0 video 19596 1 i915 iwconfig lo no wireless extensions. eth0 no wireless extensions. ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:c1:c6:45 inet adr:192.168.1.54 Bcast:192.168.1.255 Masque:255.255.255.0 adr inet6: fe80::290:f5ff:fec1:c645/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:4513 erreurs:0 :0 overruns:0 frame:0 TX packets:4359 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:3471675 (3.4 MB) Octets transmis:712722 (712.7 KB) Interruption:44 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:686 erreurs:0 :0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 Octets reçus:64556 (64.5 KB) Octets transmis:64556 (64.5 KB) sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. uname -r -m 3.2.0-30-generic x86_64 cat /etc/network/interfaces auto lo iface lo inet loopback nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Connexion filaire 1] ------------------------------------------ Type: Wired Driver: jme State: connected Default: yes HW Address: 00:90:F5:C1:C6:45 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.54 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 sudo rfkill listrfkill list 1: hci0: Bluetooth Soft blocked: no Hard blocked: no The absence of line "Kernel driver in use:" the return of lspci-k made ??me think that it is not loaded yet but he seems to be. lsmod | grep rtl8192ce rtl8192ce 137478 0 rtlwifi 118749 1 rtl8192ce mac80211 506816 2 rtl8192ce,rtlwifi I found something disturbing in / var / log / syslog Sep 14 11:40:11 pcroger kernel: [ 64.048783] rtl8192ce-0:rtl92c_init_sw_vars():<0-0> Failed to request firmware! Sep 14 11:40:11 pcroger kernel: [ 64.048795] rtlwifi-0:rtl_pci_probe():<0-0> Can't init_sw_vars. Sep 14 11:40:11 pcroger kernel: [ 64.048835] rtl8192ce 0000:02:00.0: PCI INT A disabled Sep 14 11:40:11 pcroger kernel: [ 64.943345] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6 frozen Sep 14 11:40:11 pcroger kernel: [ 64.943358] ata1.00: failed command: READ FPDMA QUEUED Sep 14 11:40:11 pcroger kernel: [ 64.943371] ata1.00: cmd 60/00:00:00:68:6a/04:00:0b:00:00/40 tag 0 ncq 524288 in Sep 14 11:40:11 pcroger kernel: [ 64.943374] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) Sep 14 11:40:11 pcroger kernel: [ 64.943381] ata1.00: status: { DRDY } Ubuntu and takes forever to start (2 min).

    Read the article

  • Do I need to be worried about these SMART drive temperatures?

    - by Steve Lorimer
    I have 5 hard drives in a machine sitting in a cupboard. /dev/sda is a 500GB Seagate drive, and is the boot disk. /dev/sd{b,c,d,e} are 2TB drives in a raid6 configuration. smartctl is showing significantly higher temperatures (like ~140 degrees celsius) on the raid drives than the boot drive. Do I need to be worried? /dev/sdb and /dev/sde are new Western Digital Black drives (new=1 week) /dev/sdc and /dev/sdd are 5 year old Hitachi drives /dev/sda [SAT], Temperature_Celsius changed from 40 to 39 /dev/sdc [SAT], Temperature_Celsius changed from 142 to 146 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 142 /dev/sdd [SAT], Temperature_Celsius changed from 142 to 146 /dev/sda [SAT], Airflow_Temperature_Cel changed from 61 to 62 /dev/sda [SAT], Temperature_Celsius changed from 39 to 38 /dev/sde [SAT], Temperature_Celsius changed from 107 to 108 /dev/sdb [SAT], Temperature_Celsius changed from 108 to 109 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sda [SAT], Airflow_Temperature_Cel changed from 62 to 61 /dev/sda [SAT], Temperature_Celsius changed from 38 to 39 Update: Adding detailed drive information as per request: /dev/sda =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Pipeline HD 5900.2 Device Model: ST3500312CS Serial Number: 5VV47HXA LU WWN Device Id: 5 000c50 02aad5ad6 Firmware Version: SC13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdb =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1398726 LU WWN Device Id: 5 0014ee 003b8bd25 Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdc =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WSTUD LU WWN Device Id: 5 000cca 369cc9f5d Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdd =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WST4D LU WWN Device Id: 5 000cca 369cc9f48 Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sde =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1483782 LU WWN Device Id: 5 0014ee 3002d235c Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled

    Read the article

  • [Android] Change language settings (locale) for the device

    - by raychenon
    Hi, I know it's possible to have multiple languages in a single application through the res/string and depending on Locale. Here is a case http://stackoverflow.com/questions/2078289/android-controling-the-user-language Now how can I change the language in the phone ? Like I'd do by Menu Settings Language & Keyboard Select locale languages Is there some real code to access to these settings ? Or should I create intent for a shortcut to the language settings. Please post some code Edit : With Locale class developer.android.com/intl/fr/reference/java/util/Locale.html The constructor is at least Locale(String language) The input is language. How can you retrieve the current language used on the device ?

    Read the article

  • Hide/ change width/ change position of UIButton based on device type

    - by Giles Van Gruisen
    I'm using the new in-app SMS features in my iPhone app, but obviously iPod Touches aren't able to send and receive SMS without support of a third party app. I know all well how to detect the device and how to hide a UIButton, but what I do not know is how to change the width of the others. Above are the three icons. The one on the far rights needs to be hidden on an iPod Touch, and the other two need to adjust size/ position to fill the remaining space. Any tips on programatically changing the position and width of a UIButton is greatly appreciated. Thanks!

    Read the article

  • WinDbg .for loop

    - by Scott
    I am having trouble getting the WinDbg .for command to work. I would like to dump an array of c++ structs. ?? gpTranData->mpApplCodes[0] works for a single entry but I would like to loop through n of these. .for ($t0=0;$t0<(gpTranData->miApplCodeCount);$t0++){ ?? &gpTranData->mpApplCodes[$t0] } sound logical to me but I get Numeric expression missing from '>miApplCodeCount);$t0++){ ?? &gpTranData->m_pApplCodes[$t0] }' Any ideas? Scott

    Read the article

  • Can't get iPhone device token

    - by d.andreykiv
    Hi. I'm trying to get iPhone device token using following code - (void)applicationDidFinishLaunching:(UIApplication *)application { // Override point for customization after app launch [window addSubview:viewController.view]; [window makeKeyAndVisible]; NSLog(@"Registering for push notifications..."); [application registerForRemoteNotificationTypes:UIRemoteNotificationTypeBadge|UIRemoteNotificationTypeAlert]; } - (void)application:(UIApplication *)application didRegisterForRemoteNotificationsWithDeviceToken:(NSData *)newDeviceToken { NSLog(@"Registered!@@"); } - (void)application:(UIApplication *)application didFailToRegisterForRemoteNotificationsWithError:(NSError *)error { NSLog(@"application:didFailToRegisterForRemoteNotificationsWithError: %@", error); if ([error code] != 3010) // 3010 is for the iPhone Simulator { // show some alert or otherwise handle the failure to register. } } but only getting "2010-04-02 18:23:35.434 Untitled[3133:207] Registering for push notifications..." What I was doing wrong?

    Read the article

  • Mobile Device emulator cannot access localhost

    - by Diana
    I am using Windows Mobile 6 Professional Emulator and Windows Mobile Device Center. I connected and cradled the emulator to my computer. I am trying to connect from the browser of the emulator to a webservice that is deployed in the IIS of my computer (same machine where the emulator is installed). If I connect my computer to the internet, I can access any website, including my local WS (using the IP returned by ipConfig). The problem is when I disconnect the computer from the Internet: I cannot access my local web service using the IP (internal one returned by ipconfig), or machine name. Do you have any ideea what settings am I missing? I am sure this it's possible somehow, I just don't know how... PS: The goal is to access the WS from a mobile application, but until I cannot access it from the browser, I cannot access it from the application either. Thank you!

    Read the article

  • iPhone: Using static library in an application crashes the device but not the iphone simulator

    - by spin-docta
    I have a library I made, and now I want to utilize it in an application. I've believe I've properly linked to the library. Here are all the things I've done: Set the header search path Set other linker flags to "-ObjC" Added the static library xcode project Made sure the lib.a was listed as a framework target Added the library as a direct dependency Like I said in the title, I've successfully run the app with the static library in the simulator. Once I try testing the app using the device, it crashes the second it has to use a function from the library: *** Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '*** +[NSDate firstOfCurrentMonth]: unrecognized selector sent to class 0x3841bb44' 2009-10-10 12:45:31.159 Basement[2372:207] Stack:

    Read the article

  • RPG Game loop and class structure (cocos2D for iPhone)

    - by mac_55
    I'm looking to make an RPG with Cocos2D on the iPhone. I've done a fair bit of research, and I really like the model Cocos2D uses for scenes. I can instantiate a scene, set up my characters etc. and it all works really nicely... what I have problems with is structuring a game loop and separating the code from the scenes. For example, where do I put my code that will maintain the state of the game across multiple scenes? and do I put the code for events that get fired in a scene in that scene's class? or do I have some other class that separates the init code from the logic? Also, I've read a lot of tutorials that mention changing scenes, but I've read none that talk about updating a scene - taking input from the user and updating the display based on that. Does that happen in the scene object, or in a separate display engine type class. Thanks in advance!

    Read the article

  • How to group data in PHP inside the while loop

    - by christian
    I query in a database and loop the result using while and heres the sample data retrieve: echo $db->f("FirstName")."===".$db->f("Question")."=".$db->f("Answer")."<br>"; Michael===Q2=allergy Michael===Q2=Hives Michael===Q6=A lot Michael===Q8_A=Daktacort Michael===Q1=Itch Michael===Q5=Smoke Michael===Q8_A=Diprogenta Christian===Q1=Stuffy Christian===Q6=A lot Christian===Q1=Clear Christian===Q5=Pollen How can I group them according to name and to their Q value? I want something like this result: Name Q1 Q2 ..... so on and so fort. Michael Itch Hives, Allergy Christian Stuffy

    Read the article

  • Brainstorming - MIDI over LAN

    - by Hunter Bridges
    I'm planning out a summer coding project for myself. I work with a lot of MIDI and have been researching it a lot. I know it's an old technology, but it works with a lot of music hardware/software so in my eyes, it's still viable. Anyway, I haven't ever worked with writing drivers or anything, so I don't know where I would start with this. So, provided I have MIDI data already being sent over LAN to a server (I know how to do that part), what steps would it take for the server to channel those received messages to an emulated MIDI device, that could then be accessed in music software and so on? Also, what would it take to also send MIDI data back through the LAN to be received by the device that originally received the message? I'm not really looking for too specific a solution. Really I am just trying to come up with a game plan right now and I need to figure out where/what to research.

    Read the article

  • Device driver with generic communication media layer

    - by Tom
    Greetings all, I'm trying to implement driver for an embedded device with generic communication media layer. Not sure what is the best way to do it so I'm seeking an advice from more experienced stackoverflow users:). Basically we've got devices around the country communicating with our head office. Usual form of communication is over TCP/IP, but could be also using usb, RF dongle, IR, etc. The plan is to have object corresponding with each of these devices, handling the proprietary protocol on one side and requests/responses from other internal systems on the other. The thing is how create something generic in between the media and the handling objects. I had a play around with the TCP dispatcher using boost.asio but trying to create something generic seems like a nightmare :). Anybody tried to do something like that? What is the best way how to do it? Cheers, Tom

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >