Search Results

Search found 2181 results on 88 pages for 'wifi cordon'.

Page 72/88 | < Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >

• ubi-partman failed with exit code 10 during 12.10 fresh install

  - by Austen

  ive been trying to install ubuntu 12.10 on my acer aspire one 534h,using an iso from the official site and a 16gb flash drive using unetbootin. my aa1 is running factory settings (xp). it will boot fine from the usb, but the installation throws the error in the title after choosing my wifi options, and contineus to give the error after every subsequent step. after trying to complete the installation ingoring the error, it hangs on the ask ubuntu screen. ive tried reformatting and reflashing (sorry, heavy android user) ubuntu to the flash drive, to no avail... do i need to format somthing else, or is it something to do with th Hdd and RAID drives? ive looked in my BIOS and found nothing related. only the option for sata or ide... any help would be great, as ive been working at this all day... edit: the error message was ubi-partman has failed with exit code 10. see (gave a directory) for more info. it then informed me that if i continued the install could be incomplete or completly broken. not sure abouth the wording in the second part, but the error is word for word... thank you.

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• Why, when on Kubuntu I lose internet connection, am I unable to reconnect?

  - by Jonathan

  Using Kubuntu 11.10. Sony Vaio computer. Network controller: Intel Corporation WiFi Link 5100. If I connect to a wireless network, and the signal drops, then I am unable to connect to any network without a reboot. I can assure that the issue has nothing to do with the computer going to sleep, as I have experienced the above while using my computer continuously. Here is exactly what happens: Connect to network (at University, where the connection is not so great). The connection is broken There are three other possible networks available, but none of them can be connected to. I have tried off and on sometimes for hours. I am always able to reestablish a connection after a reboot. I can only think of two explanations. The first is that a temp file is corrupted when the internet connection is abruptly dropped. The second is that my computer actually corrupts something before the loss of internet connection, which causes the loss in signal, and inability to reconnect. However, I am not confident that my explanations are complete, nor do I have any idea how to test these things.

  Read the article

• Network connection fails when downloading data

  - by Guus

  In the past few weeks, I've noticed my network connection becoming unstable while downloading files. I'm not sure how to diagnose this issue. I've found that my network connections appear to be temporarily unresponsive (for periods up to a minute or so) while I'm downloading a file (that's large enough to not be downloaded instantly). The problem occurs when downloading data through a webbrowser, but also when using SCP to download data from a remote location. During the period in which network connections are unresponsive, every resource that I try to access over the network is unavailable. This includes: The download itself (SCP reports a 'stalled' download) Web pages (won't load - browsers report 'resource unavailable') SSH sessions (CLI freezes) VPN connections (connections terminate) IM client connections (client starts reconnection attempts) ... (everything is pretty much dead) I've noticed that during such a period, I cannot even access the (web-based) administrative console of the router on my LAN at home (although it remains reachable for other devices). The problem occurs when connected to my home network, but also when I'm in the office. Other devices than my laptop are not affected. Given the above two characteristics I assume the problem cause lies within my laptop, not the network infrastructure. I'm running Ubuntu 11.10. Apart from applying automatic updates from Ubuntu, I can't think of a change that I applied to the OS that could have started the problems. I'm absolutely positive that this issue did not occur up to a few weeks ago (as it's very noticeable, and only started to annoy me in the last few days). When the problem occurs, applications that make use of a network connection fail visibly (I get popups telling me that a VPN connection is broken, for instance). The network manager does not report any issues related to my wifi-connection though. Help?

  Read the article

• Intel 5100 AGN disconnects and then disables my Verizon FiOS Actiontec router

  - by Anthony

  I am a new user (my first trial) of Ubuntu and booted up my Windows Vista laptop up with the Ubuntu CD. I was able to connect wirelessly to my router and stay connected for about a minute. After that it would disconnect and my router would be disabled: none of my other wireless devices would see the signal any longer, as if it disappeared. I would have to cycle the router's power toggle off/on to get it to come back on and put out a signal again. This happened repeatedly. I experienced no other problems trying the software (i.e., accessed my files w/o issue). I did not attempt to connect with an Ethernet cable. Here are the specs on my system: laptop is HP Pavilion dv5 Notebook PC system type is 64-bit operating system CPU is Intel Core 2 Duo P8600 2.4GHz ram is 4 GB network card is Intel WiFi Link 5100 AGN I read elsewhere in this forum that 64-bit systems may not be compatible with Ubuntu. Can anyone help me with this? I'd really like to be able to use this op system.

  Read the article

• CodePlex Daily Summary for Sunday, August 26, 2012

  CodePlex Daily Summary for Sunday, August 26, 2012Popular ReleasesPhysics Helper XAML: Physics Helper XAML 1.1.0.0: This release supports creation of 2D Physics apps for Windows 8 RTM, Windows Phone 7.1 development, and Silverlight 5. It includes source code and samples in three separate solutions.TouchInjector: TouchInjector 1.0: Version 1.0BlackJumboDog: Ver5.7.1: 2012.08.25 Ver5.7.1 (1)?????·?????LING?????????????? (2)SMTP???（????）????、?????\?????????????????????Peulot Heshbon: Peulot Heshbon version 3.0.0: Available quizzes:Plus for Natural, Real and fragments Minus for Natural, Real and fragments Multiplication for Natural, Real and fragments Divide for Natural, Real and fragments Random for Natural, Real and fragments Compare 2 percentages Compare 2 fragments (Just for easy difficulty) Check if a number can be divided with another number exactly. Available Languages:Hebrew English Russian What's NewAdded new quiz: Compare 2 fragments. It is available only if you are in Eas...Visual Studio Team Foundation Server Branching and Merging Guide: v2 - Visual Studio 2012: Welcome to the Branching and Merging Guide Quality-Bar Details Documentation has been reviewed by Visual Studio ALM Rangers Documentation has been through an independent technical review Documentation has been reviewed by the quality and recording team All critical bugs have been resolved Known Issues / Bugs Spelling, grammar and content revisions are in progress. Hotfix will be published.Microsoft Ajax Minifier: Microsoft Ajax Minifier 4.62: Fix for issue #18525 - escaped characters in CSS identifiers get double-escaped if the character immediately after the backslash is not normally allowed in an identifier. fixed symbol problem with nuget package. 4.62 should have nuget symbols available again.nopCommerce. Open source shopping cart (ASP.NET MVC): nopcommerce 2.65: As some of you may know we were planning to release version 2.70 much later (the end of September). But today we have to release this intermediate version (2.65). It fixes a critical issue caused by a third-party assembly when running nopCommerce on a server with .NET 4.5 installed. No major features have been introduced with this release as our development efforts were focused on further enhancements and fixing bugs. To see the full list of fixes and changes please visit the release notes p...MyRouter (Virtual WiFi Router): MyRouter 1.2.9: . Fix: Some missing changes for fixing the window subclassing crash. · Fix: fixed bug when Run MyRouter at the first Time. · Fix: Log File · Fix: improve performance speed application · fix: solve some Exception.eel Browser: eel 1.1.0.41 beta: Improved UI New features Bug fixesDynamics CRM 2011 Dummy Entity: First Release: This has been tested on CRM 2011 RU8 On-Premise IFD. Known Issue: The Test Dummy CRM page load event may throw an exception loading the first time as the iframe may not have finished loading. I have not been able to get the iframe OnReadyStateChange event to fire. But it is only a sample anyway. The zip file contains: Dummy Entity Visual studio solution. Test Dummy Visual Studio solution. Dummy Entity CRM Solution Test Dummy CRM Solution Installation: Unzip and import the CRM Solutions...Private cloud DMS: Essential server-client full package: Requirements: - SQL server >= 2008 (minimal Express - for Essential recommended) - .NET 4.0 (Server) - .NET 4.0 Client profile (Client) This version allow: - full file system functionality Restrictions: - Maximum 2 parallel users - No share spaces - No hosted business groups - No digital sign functionality - No ActiveDirectory connector - No Performance cache - No workflow - No messagingJavaScript Prototype Extensions: Release 1.1.0.0: Release 1.1.0.0 Add prototype extension for object. Add prototype extension for array.Glyphx: Version 1.2: This release includes the SdlDotNet.dll dependency in the setup, which you will need.TFS Project Test Migrator: TestPlanMigration v1.0.0: Release 1.0.0 This first version do not create the test cases in the target project because the goal was to restore a Test Plan + Test Suite hierarchy after a manual user deletion without restoring all the Project Collection Database. As I discovered, deleting a Test Plan will do the following : - Delete all TestSuiteEntry (the link between a Test Suite node and a Test Case) - Delete all TestSuite (the nodes in the test hierarchy), including root TestSuite - Delete the TestPlan Test c...ERPStore eCommerce FrontOffice: ERPStore.Core V4.0.0.2 MVC4 RTM: ERPStore.Core V4.0.0.2 MVC4 RTM (Code Source)ZXing.Net: ZXing.Net 0.8.0.0: sync with rev. 2393 of the java version improved API, direct support for multiple barcode decoding, wrapper for barcode generating many other improvements and fixes encoder and decoder command line clients demo client for emguCV dev documentation startedScintillaNET: ScintillaNET 2.5.1: This release has been built from the 2.5 branch. Issues closed: Issue # Title 32524 32524 32550 32550 32552 32552 25148 25148 32449 32449 32551 32551 32711 32711 MFCMAPI: August 2012 Release: Build: 15.0.0.1035 Full release notes at SGriffin's blog. If you just want to run the MFCMAPI or MrMAPI, get the executables. If you want to debug them, get the symbol files and the source. The 64 bit builds will only work on a machine with Outlook 2010 64 bit installed. All other machines should use the 32 bit builds, regardless of the operating system. Facebook BadgeDocument.Editor: 2013.2: Whats new for Document.Editor 2013.2: New save as Html document Improved Traslate support Minor Bug Fix's, improvements and speed upsPulse: Pulse Beta 5: Whats new in this release? Well to start with we now have Wallbase.cc Authentication! so you can access favorites or NSFW. This version requires .NET 4.0, you probably already have it, but if you don't it's a free and easy download from Microsoft. Pulse can bet set to start on Windows startup now too. The Wallpaper setter has settings now, so you can change the background color of the desktop and the Picture Position (Tile/Center/Fill/etc...) I've switched to Windows Forms instead of WPF...New Projects508 Compliance Validator: This tool checks aspx and ascx pages against 508 Accessibilty guidelines and also allows you to add your own rules.BF for WP: BF for WP is a visual Brainfuck interpter for Windows Phone.Climate Control: App lets you vote on whether you're too hot or too cold so the dummy next to the air con controls can adjust the thermostat.Custom Captcha Plugin for Kooboo CMS for adding content or sending feedback: Custom Captcha Plugin for Kooboo CMS for adding content or sending feedbackGalleryDownloader: This project takes aim on downloading free photogalleries through the Internet. Highly Maintainable Web Services: The Highly Maintainable Web Services project is a reference architecture application for .NET that demonstrates how to build highly maintainable web services.Its.Validation: A C# DSL for writing rules in a composable, functional style.Kaku by wifi: The projects purpose: Make your phone a part of your house hold by being able to control certail elektric devices with your phone such as, light, electric curtaLogin with Google in ASP.Net MVC3 & Get data from Google User: ASP.Net developer can use this code: asp.net mvc3 web project which contains login with google and pull data from user's google accountMabiCommerce: MabiCommerce is an advanced Commerce Calculator for the MMORPG Mabinogi.Mapture the FLAG: A location based game for wp7mn: sumSharePoint 2010: SharePoint 2010 utilitiesSHIORI.NET: ???SHIORI????????????????????Temp and Stress: Tieni sotto controllo le temperature della tua CPU e effettua Stress Test e Benchmark!VisiblityControl – An Alternative to Converters: A templated content control hosting to remove the pain of using the BooleanToVisibilityConverter. The property IsTrue determines what is shown.Whatsnexx Integration for Orchard CMS: Orchard Whatsnexx makes it easier for Orchard users to send an event to the Whatsnexx Ticket Bus service API, of the Whatsnexx GatewayWINRT \ Metro Store \ open marketing solution: This project is aimed at creating a public shopping cart, that is available to all windows 8 users free. products are screened added by administrators

  Read the article

• Help setting up wireless in Ubuntu 13.04

  - by James

  I'm having problems connecting my WIFI in Ubuntu 13.04 . So I was wondering if filling in the data manually ie: the IPv4, IPv6, the SSID and BSSID info etc. I did try this before but maybe I put in the wrong data or maybe not enough. Would that make it work? I just don't know how to find out some of the data you need to put in? I'm new and it's confusing. Does anyone know the solution? Here is lspci: james@james-MM061:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 01) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 01) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01) 03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) 0b:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) Computer information: Model: Dell MM061 Mobile Intel(R) 945GM Express Chipset Family [Display adapter] (2x)

  Read the article

• 12.04 disabling wireless via dbus does not work

  - by FlabbergastedPickle

  I am using a proprietary rt3652sta driver for my wireless card. It appears as a ra0 device on the 64-bit Ubuntu 12.04. According to the online documentation the following used to work definitely up to 10.04. dbus-send --system --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.DBus.Properties.Set string:org.freedesktop.NetworkManager string:WirelessEnabled variant:boolean:false This however has no effect on the aforesaid wireless card in 12.04. Also, rfkill does not work as it does not even list the wireless button (again, likely due to the wireless driver being proprietary): rfkill list It only lists the hci0 (bluetooth) one and one can block/unblock it accordingly but this has no effect on the wifi. ifup/down also does not work (AFAICT)... And this leaves me with disabling wireless through the network manager applet. However, trying to do so via dbus appears not to work and yet I would like to automate it via a script. Any ideas how I could find out the proper dbus structure for the call? Is this even possible in Ubuntu 12.04?

  Read the article

• Ubuntu 12.04 Freezes at Bootup

  - by Ryan Yu

  I have an Acer Aspire One Model AO722, that has a dual-boot configuration with Windows 7 Home Premium and Ubuntu 12.04. Processor: AMD C-50, 1.00GHz 2.00GB ram, 64-bit, AMD Radeon HD 6250 Graphics. I installed Ubuntu two days ago, and since then, loading it has been sporadic. Windows 7 still loads just fine, but Ubuntu will sometimes freeze. First time I booted Ubuntu up, it ran no problem. Worked with it for half an hour, then shut down the computer. The second time I booted it up, it froze after ten minutes when I was trying to set up Thunderbird. Third time, same thing. Fourth time, it froze about 5 minutes after bootup when I was trying to connect to my wifi. Fifth time, it ran no problems for about 5~ hours. Then, three consecutive times I've restarted (what is it, the 6th, 7th, and 8th times?) it has gotten to the login screen, I've entered my password, all the text on the page disappears as if its going to load my desktop, and it freezes. A minute ago when I booted Ubuntu up for the 9th time, it loaded the desktop fine. Who knows if it'll crash soon; probably, though. Any ideas?

  Read the article

• Can't enable bluetooth because of adapter

  - by Eray

  I can't use my Bluetooth with Ubuntu 12.04 64bit . I have installed bluetooth, gnome-bluetooth and blueman packages. But i'm getting No adapter found error. eray@eray-vaio-ubuntu:~$ sudo hciconfig hci0 reset [sudo] password for eray: Can't init device hci0: Connection timed out (110) eray@eray-vaio-ubuntu:~$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: sony-wifi: Wireless LAN Soft blocked: no Hard blocked: no 3: sony-bluetooth: Bluetooth Soft blocked: no Hard blocked: no eray@eray-vaio-ubuntu:~$ sudo hciconfig sony-bluetooth reset Can't init device hci0: Connection timed out (110) eray@eray-vaio-ubuntu:~$ I'm remambering, i was able to use my bluetooth with Ubuntu, about 7-8 months ago. So Ubuntu supporting my bluetooth device. How can i install my bluetooth and solve this problem ? NOTE , I've read a lots of question about this. Generally there are 3 answers. Upgrade to 12.04 execute sudo hciconfig hci0 reset command unblock your device if it's blocked. But as you seen, none of them helped me. Because of this, i'm asking this question.It's not a duplicated question.

  Read the article

• Wireless will not connect on an Asus U56? [closed]

  - by ernie

  I have an ASUS U56. I could connect to internet without delay or problems in Ubuntu 11.04. Now, running Ubuntu 11.10, I have not been able to connect. I can see the network and the computer tries to connect, but never makes the connection. I have been trying to fix this problem since the release date of 11.10. I had to install the older kernel 2.6 to get the wifi to work. Any other solutions? ernest@ernest-U56E:~$ ifconfig eth0 Link encap:Ethernet HWaddr 14:da:e9:25:6c:d0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:53 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 40:25:c2:3f:46:d4 inet addr:192.168.xx.xxx Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::4225:c2ff:fe3f:46d4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:44962 errors:0 dropped:0 overruns:0 frame:0 TX packets:32287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:35614976 (35.6 MB) TX bytes:5400816 (5.4 MB) ernest@ernest-U56E:~$

  Read the article

• Review of TechEd 2012 - so far

  - by Stefan Barrett

  Disclaimer: probably going to next years TechEd.  (but not 100% sure) As with most TechEd's, this is not one of the best - but it's not bad.  Some impressions so far: The food is not bad, through perhaps not as much choice as in previous years.  The snacks, while a bit limited, are at least available.  The alumni lounge is ok, through perhaps not as good as last years.  Wifi is a bit worse than previous years - not really working in the big room, and a bit sporadic in the rest of the building. The device seems to make a big difference - the iPad seems to connect the easiest, while the iPhone & Lumia 800 are really struggling.  The real problem is the content - not as developer focused as in previous years.  This shows up in a number of different ways, for example while there is a visual studio booth, there is not much sign of anybody from the language teams.  This is one of few TechEd's where I don't feel very surprised about anything - seen most of the developer stuff in previews. One example where I was surprised was the pre-conf on c++ - its been years since I did any c++, but based on that session perhaps I should start again. While there are sessions, I'm not finding my schedule very challenged. For each time-slot there only seems to 1, or rarely 2, interesting sessions.  The focus seems to be on windows 8, Azure and the phone, which while interesting (might give win8 a go), are not enough.

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• "Unable to install GRUB in /dev/sda" when installing GRUB

  - by vicban3d

  I recently bought a shiny new Lenovo Yoga 2 Pro and I want to dual boot it with Ubuntu for studying purposes. Its built-in OS is Windows 8.1 and it has a 256GB SSD. I've made a separate 90GB partition just for Ubuntu and a live USB to install it. The first time everything seemed to work great, I solved the wifi issued by blacklisting ideapad_laptop, the installation went flawlessly and Ubuntu worked fine. When I got up the next morning and turned on my laptop it booted into Windows right away without ever showing the GRUB menu. So I tried to reset, and checked my partitions with the Disk Manager and everything looked fine. Since I couldn't find a solution online I went ahead and formatted the partition to try and install again. This time and every time since, the installation was aborted and I got a fatal error saying: Unable to install GRUB in /dev/sda Executing `grub-install /dev/sda` failed. This is a fatal error. Can anyone please suggest a solution to this problem? If any further information is needed I would be happy to provide it. Thanks. When installing I get the following in details: ubuntu kernel: [ 1946.372741] FAT-fs (sda2): error, fat_get_cluster: invalid cluster chain (i_pos 0). ubuntu grub-installer: error: Running 'grub-install --force failed.

  Read the article

• Impossible to enable bluetooth under Ubuntu

  - by PCh

  I just installed Ubuntu 12.04 (dual boot, kept Windows just in case) on my new Acer Aspire One 756-877. As soon as I installed it I also installed the Broadcom driver, since wifi wasn't working, and that solved it right away. But when I tried Bluetooth, I had a problem that I see is quite recurring: -The hardware is on (and working fine under Windows) -The icon shows up on the menu, giving me the options of turning Bluetooth on or off, and then just "Bluetooth preferences". -I can apparently turn it on that way, which only lights up the icon but makes no difference at all (and doesn't give any other options in the Bluetooth menu) -When I open "Bluetooth preferences" (whether Bluetooth is apparently on or off, it makes no difference), it says it's disabled and will not let me slide the button to enable it. I've rebooted, but nothing happens. -The material is Broadcom and the port (if it's relevant at all) is Port_#0001.Hub_#0003 I tried the following commands suggested in other similar questions, with no result at all: sudo dmesg | grep blue and sudo service bluetooth start and sudo /etc/init.d/bluetooth start Any other clues on what I can do? Thanks for your time!

  Read the article

• ISP issue browsing "sonos.com" - need to diagnose and prove [closed]

  - by john

  I am unable to browse to a website "sonos.com" with my ISP (virgin). I have ruled out browsers, PCs, macs, routers, wifi, etc. Other ISPs (even other virgin connections in different areas!) supply this site no problem. I am 99% convinced there is a DNS issue lurking here. There is something fishy about the DNS for the site : What I notice is that online DNS sites tell me the right IP address for "sonos.com", but not for "www.sonos.com". Anyway when I type "sonos.com" the browser (any/all of the 4 I tried) fail to display the page. Firefox gives a "connection was reset" error. If I browse to sonos.com using the IP address it works OK. Browsing to www.sonos.com or sonos.com works fine with other ISPs of course. Questions: 1 Does anyone have any idea what might be going on here? 2 Any suggestions as to tools/monitors to help investigate/prove what is going on I can then take this up with virgin and/or sonos. Thanks

  Read the article

• Sound card not detected in 13.04

  - by Ganessh Kumar R P

  I have a problem with my sound card. I don't have volume up or down option anywhere. In the setting -> Sound I don't have any card detected. But when I run the command sudo aplay -l, I get the following output **** List of PLAYBACK Hardware Devices **** Failed to create secure directory (/home/ganessh/.config/pulse): Permission denied card 0: MID [HDA Intel MID], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 9: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 And the command lspci -v | grep -A7 -i "audio" outputs 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 48 Memory at f0f20000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) (prog-if 00 [Normal decode]) -- 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: Dell Device 02a2 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d3efc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 So, I assume that the drivers are properly installed but still I don't get any option in the settings or volume control. The same card used to work well back in 2010 versions(04 and 10) Any help is appreciated. Thanks

  Read the article

• Can't connect to Wireless Network - Ubuntu 12.04 LTS & Sabrent A111N USB Dongle

  - by Ohgodwhy

  I've been trying to connect to this network for quite some time. I can't directly connect to the router with a Wire, but can access the Router with other wireless devices without any issues. I had previously tried several other Wifi nic's but none of them would load properly. Today, i went and bought a new (supported) Sabrent A111N USB Dongle, which said explicitly that it works with Linux 2.4 +. I popped the Dongle in, and low-and-behold it immediately said that there were Available Wireless Connections. I selected my connection and tried to connect, but it just loops constantly while saying Wireless Disconnected then attempts to connect again over and over. ifconfig and iwconfig both show my device in a ready and working state. However, iwlist wlan0 scan says that there are no results found. I don't get it... At one point, I could see the CPU in the DHCP client list under the router, but it doesn't fully make the connection (something about a timeout?). Any help would be appreciated. Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• Install a i386 printer driver into an amd64 distribution or how can I find a good printer based on features?

  - by Yanick Rochon

  Hi, I just bought a Lexmark Interpret S408 all-in-one printer. The box said that it supported Ubuntu 8.04, but I told myself it should work with Lucid... well no. The only driver I have found is for i386 while I have a amd64 image installed; the architecture is incompatible. So, the quesiton is : Is it possible to install that driver anyway, somehow? Or do I need to take that printer back to the store and buy another one? If the latter is the only alternative, I need a printer that has wireless connection capability can do color printing is of good price (less than $200 CAD) Thank you for your answers, help, and tips. ** UPDATE ** The driver was given in the form of deb package (for Debian distributions) and I managed to extract the actual deb package driver out of the install program. I ran sudo dpkg -i --force-all lexmark-inkjet-09-driver-1.5-1.i386.deb and the driver installed, and I was able to print something out. But that pretty much ends there; I cannot access anymore of the printer settings, etc. (i.g. scanner, fax, wifi settings, etc.) I should suffice for now as I'm satisfied with the printer's features (and size, and prince), but if I could have a full-linux-supported printer like that one, I would return this one in exchange for the other.

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• Computer becomes unreachable on lan after some time

  - by Ashfame

  I work on my laptop and ssh into my desktop. I use a lot of key based authentication for many servers for work but recently I couldn't login because ssh would pick up and try all the keys and it stops trying before ultimately falling back to password based login. So right now I am using this command: ssh -X -o PubkeyAuthentication=no [email protected] #deskto The issue is after sometime the desktop would just become unreachable from laptop. I won't be able to open its localhost through IP and today I tried ping'in it and found a weird thing. Instead of 192.168.1.4, it tries to ping 192.168.1.3 which I am sure is the root cause as it just can't reach 192.168.1.4 when its actually trying for 192.168.1.3 Ping command output: ashfame@ashfame-xps:~$ ping 192.168.1.4 PING 192.168.1.4 (192.168.1.4) 56(84) bytes of data. From 192.168.1.3 icmp_seq=1 Destination Host Unreachable From 192.168.1.3 icmp_seq=2 Destination Host Unreachable From 192.168.1.3 icmp_seq=3 Destination Host Unreachable From 192.168.1.3 icmp_seq=4 Destination Host Unreachable From 192.168.1.3 icmp_seq=5 Destination Host Unreachable From 192.168.1.3 icmp_seq=6 Destination Host Unreachable From 192.168.1.3 icmp_seq=7 Destination Host Unreachable From 192.168.1.3 icmp_seq=8 Destination Host Unreachable From 192.168.1.3 icmp_seq=9 Destination Host Unreachable ^C --- 192.168.1.4 ping statistics --- 10 packets transmitted, 0 received, +9 errors, 100% packet loss, time 9047ms pipe 3 Also the ping command message comes in multiple and not one by one. (izx answer's the weirdness I thought there was in ping command.) I did check for desktop, its local IP is still the same, so something is going on in my laptop. Any ideas? P.S. - Laptop runs Ubuntu 12.04 & Desktop runs Ubuntu 11.10 Laptop is connected through wifi to router and Desktop is connected through LAN to router. Update: Even after setting up static IP leases in router settings, I again ran into this issue.

  Read the article

• Computer Says No: Mobile Apps Connectivity Messages

  - by ultan o'broin

  Sharing some insight into connectivity messages for mobile applications. Based on some recent ethnography done my myself, and prompted by a real business case, I would recommend a message that: In plain language, briefly and directly tells the user what is wrong and why. Something like: Cannot connect because of a network problem. Affords the user a means to retry connecting (or attempts automatically). Mobile context of use means users use anticipate interruptibility and disruption of task, so they will try again as an effective course of action. Tells the user when connection is re-established, and off they go. Saves any work already done, implicitly. (Bonus points on the ADF critical task setting scale) The following images showing my experience reading ADF-EMG Google Groups notification my (Android ICS) Samsung Galaxy S2 during a loss of WiFi give you a good idea of a suitable kind of messaging user experience for mobile apps in this kind of scenario. Inline connection lost message with Retry button Connection re-established toaster message The UX possible is dependent on device and platform features, sure, so remember to integrate with the device capability (see point 10 of this great article on mobile design by Brent White and Lynn Hnilo-Rampoldi) but taking these considerations into account is far superior to a context-free dumbed down common error message repurposed from the desktop mentality about the connection to the server being lost, so just "Click OK" or "Contact your sysadmin.".

  Read the article

• How do I bridge my wireless to my wired connection?

  - by gatoatigrado

  I want to bridge the wireless connection with the wired connection. The wireless is the host and the wired is the client, so to speak. Internet sharing (inet <--> wifi <--> ethernet) I tried to bridge my ethernet connection by going to network manager edit connections wired edit IPv4 settings shared to other computers Screenshots However, it seems to automatically disconnect half a second after it says "connection established"! edit 2 got the network manager logs, it seems the address is in use. See http://pastebin.com/DjqRshxW , line 45. nm-tool output is here: http://pastebin.com/x5Aci5V1 . I tried firestarter, as mentioned in another thread, and no luck. I don't have time to bother with a dozen command line tricks, unless is copy & pasting a shell script... so please suggest ways that use GUIs and/or won't leave my computer in a confused state (e.g. disabling network manager, manually connecting to a WPA network, installing brutils, etc.). edit: one idea that would work, if it's possible -- is there a way to share connections via SSH and SOCKS5? I'd need to do this at a system-wide level though; I only know how to do it through the browser now. Then, I could run ifconfig eth0 192.168.4.1 on the computer sharing the inet, and ifconfig eth0 192.168.4.2 on the computer I'm trying to share with; I know this does work for host-to-host transfers. edit 3 If I run sudo killall dnsmasq, then nothing is using the 10.42.43.1 address the network manager sharing wants to use. But now it just takes longer to die, with error "NetworkManager[5935]: dnsmasq died with signal 9" [ http://pastebin.com/4FNtpugi ]. Looking at just the commands [ http://pastebin.com/1vrtQeWk ], maybe it's trying to route eth0 to itself? I'm not that familiar with networking things though.

  Read the article

• AR242x / AR542x wireless card not working

  - by Pipan87

  My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

  Read the article

• HP G42 Ubuntu live cd failure

  - by Jon

  Ok, I have tried every option under the sun. I have surfed through the internet for a good 3 hours straight and to no effect. I installed ubuntu on my HP G42 laptop, it worked fine, then when I tried installing the standard after installation updates my wifi failed. In my attempt to fix my wi-fi I rebooted my laptop, when I rebooted I was stuck on a black screen with nothing that I tried to fix it helping the situation. So I then tried to fix it by reinstalling Ubuntu. When I attempted to boot into the live ccd it failed leaving with the now familar black screen. After numerous attempts using instructions from live cd and instal failure blank screen... page and replacing my hard drive at a cost of $65 I am coming here for help. As for the actual DVD that I tried installing ubuntu from it was able to install ubuntu on a mac just fine after my issues on the HP. After installing the hard drive I loaded up windows just fine but I don't want windows I want ubuntu, can you please provide instructions on how to install ubuntu?

  Read the article

< Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79  | Next Page >