Search Results

Search found 2181 results on 88 pages for 'wifi cordon'.

Page 79/88 | < Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >

• ssh from 1 ubuntu box to another ubuntu box

  - by michael

  Hi, I have 2 ubuntu boxes in a WiFi network. Below is the 'ifconfig' of my destination machine. But in my source machine, I tried 'ssh 192.168.1.2' I get connection refused. $ ifconfig eth0 Link encap:Ethernet HWaddr c8:0a:a9:4d:d6:6a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:35 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4508 errors:0 dropped:0 overruns:0 frame:0 TX packets:4508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:330441 (330.4 KB) TX bytes:330441 (330.4 KB) wlan0 Link encap:Ethernet HWaddr 00:23:14:32:e8:dc inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:14ff:fe32:e8dc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:319828 errors:0 dropped:0 overruns:0 frame:0 TX packets:618371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30642011 (30.6 MB) TX bytes:921522542 (921.5 MB) How to set up so that I can ssh from 1 box to another?

  Read the article

• Why does my DD-WRT not accept SSH connections from my laptop?

  - by Vlad Seghete

  So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

  Read the article

• My internet drops and will only reconnect if I troubleshoot it or restart my computer.

  - by Paul

  My internet loses its connection and at the same time, and my speaker seems broken if that happens and my mouse will not be smooth as it was before it happens. It already happened before and I didnt mind it. But now, it's happening literally all the time. After startup, my connection seems okay but after some few minutes, even without me doing something, my laptop will just lose its connection. It says that it is not connected and connections are available, but if I check if there are connections where I can connect it shows nothing. Even if, there is actually a wi-fi connection where my phone and other laptops connect. They dont seem to have problem with it. Just my laptop. After that happens, I usually restart my laptop but I discovered that troubleshooting it would somehow repair the problem, but not all the time. It says that restarting my wireless adapter do the job. Are there any long term fix? I mean that could last long or totally erase the problem? I have Atheros AR5B97 Wireless Network Adapter and Microsoft Virtual WiFi Miniport Adapter, both enabled. On the services, I have Wired AutoConfig and WLAN AutoConfig on Automatic. Aspire 4750, Windows 7 (x86)

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• Xmonad on windows laptop

  - by Kevin L.

  I'm a Linux developer in the market for a laptop. 90% of my time is spent in Emacs, the terminal, and Google Chrome, and I want to use them within the excellent Xmonad tiling windows manager. Given these constraints, I can only see two options: Run Linux on a laptop Run Windows on the laptop, and spend all of my time working within a Linux VM. Years of experience suggest that the first option will take many frustrating hours and probably be suboptimal w.r.t. battery life, wifi, and fn keys like screen brightness or audio adjustment. For the second option, what would be the ideal setup? I've had a lot of luck with Cooperative Linux on my Samsung NC-10 netbook (Windows XP), but I would have to setup the X11 server myself. What about using VirtualBox (which includes the guest VM's GUI)? Has anyone tried this? Hardware-wise, I'm looking for something in the "Macbook Air killer" category; Samsung Series 9 laptop, Lenovo IdeaPad U300s, &c. (i.e., matte screen, 5h+ battery life, 3ish pound weight). Price is not a consideration; any suggestions?

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• Internet Sharing on Lion breaks my routing table

  - by seaders

  When in the office, I'm connected to a 192.168.1.0/24 network. When Internet Sharing is off, when I run netstat -nr the first entry shows default 192.168.1.254 UGSc 10 62 en0 If I turn Internet sharing on, it shows default link#5 UCS 2 0 en1 This is obviously incorrect and breaks all connectivity of my machine. en1 is my wireless, whereas en0 is my ethernet. If I then disable Internet Sharing, it even deletes that incorrect route, so I'm left with no default route at all. Currently I have one script that I run when I share, or after, when I disable that does route delete default route add default 192.168.1.254 That fixes everything, but I'd love to know what's actually making this happen and how to properly fix it. And just to say that at some point a few months ago, this was working absolutely perfectly, with no hitches, then one day when I brought the laptop home, I couldn't disable the internet sharing, so I couldn't connect to my home wifi. I eventually had to restart the machine and since then this problem has been happening. Any help would be greatly appreciated, thank you.

  Read the article

• How to configure a Linux kernel based on the modules currently in use?

  - by Carla

  Hello, I'm willing to build a minimal kernel with only the needed things for my machine; so I started by compiling the kernel from the ground up, using the default configuration and adding things that I know for sure I have (i.e.: Ethernet card, WiFi card, ...). But there are several other things not so easy to know about (i.e.: the watchdog timer) so I came across AutoKernConf which supposedly detects the hardware of the machine and generates a kernel configuration file with the settings for the found devices. The problem is it contained several settings repeated and even some which I don't have (I'm using a Dell laptop and one of the things it "found" was something of a Toshiba one). So I ended up building a kernel with the configuration that came out of the make allmodconfig command, which is a kernel with most of the things compiled as modules. Booting into that kernel and running lsmod I can see all of the kernel modules in use (the ones really needed) and I would like to know if there is a tool or some way for me to parse that list and convert it to the corresponding kernel configuration file. Or how to map each one with the appropriate options in the kernel so that I can manually set them. Thank you very much for your time.

  Read the article

• Linux/hostapd: AP can ping clients, clients can access internet, can't access www@wlan1 with more than 5-6 packets at once

  - by mhambra

  Please edit the title, can't make it sound better. -- OP. Hi all, I have a Wifi USB dongle in a PC, that serves as an AP for laptop. wlan1: 192.168.2.1, netmask 255.255.255.0, routed: route add -net 192.168.2.0 netmask 255.255.255.0 gw 192.168.2.1 ping 192.168.2.2 (laptop): ping was ok for lot of packets. Now, I try to access 192.168.2.1:80/myindex.html (apache) from laptop, and can see that own 1kb test page. But, trying to access 192.168.2.1:80/my.jpg, I see the following: GET /my.jpg HTTP/1.1 200 OK <jpg header, about a kilobyte> <TCP packet retransmisson> <TCP packet retransmisson> <end of stream> It seems to be a hostapd's problem (networked stuff worked fine with Ad-Hoc), but it may be also forwarding/routing problem too. What to google for? Even more strange, SSH to that host works fine.

  Read the article

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• How to display escaped characters in tmux status bar

  - by walrus

  i am running tmux from a tty on an embedded linux device. (NOT a terminal emulator) because the screen is rather small, i want to add some "icons" to the tmux status bar. to achieve this, i have simply created a font with the appropriate glyphs for things like battery, or wifi. i can load the font, and display the characters with calls that use an escape to the line drawing characters like so: echo -e "\xe\234\xf" \xe escapes me into line drawing character mode, \234 is my created character, and \xf returns me to normal character mode so my terminal doesnt start getting goofy. this works perfectly if i enter the command at the terminal whether tmux is started or not. the issue arises if i then try to use it in my ~/.tmux.conf file for the status bar. i currently have a line like this: set -g status-right "#(echo -e "\xe\234\xf") #(/script/to/output/powerlevel) this simply outputs \xe\234\xf powerlevel this goes the same if i try printf over echo. this is the output i would expect to get on the terminal if i made the call without passing -e to echo, or without enclosing the statement with quotes. i then decided to wrap the calls to the echo or printf in a shell script. again, the script works when called from the terminal, but not in tmux's status bar. now i get the unprintable character "?" instead of my icon, like this: ? powerlevel this is what i would expect if i did not use the line drawing escapes previously mentioned above, or if i tried to copy and paste the character as text using tmux. in addition, the calling of these character scripts screws up the rest of my status-right, as the clock has about 6 digits for minutes when it is called (though it correctly only updates two of them). how can i make tmux respect the escape characters? any help or insight is greatly appreciated.

  Read the article

• unable to access Internet by wireless but can by cable

  - by Jeff King

  i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

  Read the article

• Unable to connect to Windows VPN from iPad

  - by Justin

  I have a 16 GB iPad wifi I can't get to connect to VPN. The error I get is: "A connection could not be established to the PP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator." I have tried a variety of tasks to troubleshoot the issue: I have verified that another iPad on another network can connect to the VPN I am trying to connect to I can connect to this VPN from the same network the iPad uses on a Windows machine I have verified an iPhone user can connect to this VPN from a different network I have reset the iPad's network settings I have reset the entire iPad and restored settings I have compared my settings w/ a screenshot from the iPad that works and confirmed everything is correct I have used the IP address and domain name of our VPN server in the settings I have tried deleting the VPN settings in the iPad and recreating them I have verified in the logs of VPN server that I'm not even getting to the VPN server (no log entry) I have verified that I cannot VPN from the iPad on separate network (different ISP and router) Are there any other ways to troubleshoot VPN on an iPad?

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Improve wireless performance

  - by djechelon

  Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

  Read the article

• Doing port forwarding and then using it from within the internal network

  - by Ram Rachum

  We all know that by doing port forwarding on the router, computers from outside the network are able, on the specified ports, to access internal computers by targeting the external IP. I'm now replacing a TP-Link router with a D-link VDSL N 6740U router, (and copied over all the settings,) and I've noticed that one thing stopped working: With the TP-link router, you could access those port-forwarded computers from within the network, using the external IP, and they would be forwarded to the relevant computers. With the new D-Link router, it doesn't work. You might be wondering, why would you want to use the external IP and port forwarding when you're inside the internal network anyway and can just access the internal IP? One example for why this is useful: You have an iPhone app that connects to a service on an internal computer. The iPhone app knows to connect to the external IP. When we put that iPhone inside the internal network (via WiFi), it suddenly stops working, because it can't access the service from the external IP anymore. Is it an inherent property of D-Link routers that they do not allow accessing internal servers from inside the network by targeting the external IP? Or is there a way to make it work?

  Read the article

• Why isn't my phone charging with some micro usb cables?

  - by Jacxel

  I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

  Read the article

• My Mac OS X 10.5 netstat reveals a lot of open UDP connections.

  - by bboyreason

  here are my netstat results (besides server-less connections): Active Internet connections Proto Recv-Q Send-Q Local Address Foreign Address (state) tcp4 0 0 192.168.1.98.49224 r1.ycpi.vip.sp2..http ESTABLISHED tcp4 0 0 192.168.1.98.49223 r1.ycpi.vip.sp2..http ESTABLISHED tcp4 0 0 192.168.1.98.49203 lax04s01-in-f189.https ESTABLISHED tcp4 0 0 192.168.1.98.49201 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49198 lax04s01-in-f19..http ESTABLISHED tcp4 0 0 192.168.1.98.49196 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49194 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49192 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49183 r1.ycpi.vip.sp2..http ESTABLISHED tcp4 0 37 192.168.1.98.49179 l1.login.vip.sp1.https CLOSING tcp4 0 0 192.168.1.98.49175 lax04s01-in-f104.https ESTABLISHED tcp4 0 37 192.168.1.98.49167 l1.login.vip.sp1.https LAST_ACK tcp4 0 0 192.168.1.98.49164 lax04s01-in-f19..https ESTABLISHED tcp4 0 0 192.168.1.98.49174 69.31.112.122.http TIME_WAIT tcp4 0 0 192.168.1.98.49173 69.31.113.83.http TIME_WAIT udp4 0 0 *.ipp **.* udp4 0 0 192.168.1.98.ntp **.* udp4 0 0 *.49628 **.* udp4 0 0 *.51997 **.* udp4 0 0 *.64675 **.* udp4 0 0 *.61947 **.* udp4 0 0 *.65152 **.* udp4 0 0 *.55643 **.* udp4 0 0 *.51704 **.* udp4 0 0 *.59757 **.* udp4 0 0 *.53643 **.* udp4 0 0 *.65346 **.* udp4 0 0 *.61960 **.* udp4 0 0 **.* **.* udp6 0 0 localhost.ntp **.* udp4 0 0 practivate.adobe.ntp **.* udp6 0 0 localhost.ntp **.* udp6 0 0 *.ntp **.* udp4 0 0 *.ntp **.* udp6 0 0 *.mdns **.* udp4 0 0 *.mdns **.** udp4 0 0 *.** **.** udp4 0 0 *.** **.** omitted a few asterisks, basically all the empty spots are asterisks what is up with all the UDP connections listening on any port? is that what this means? the internet activity that should be going in is that i connected via wpa to wifi at a small restaurant visited a few pages, checking mail from a few different accounts, no new mail or downloads where done. ?

  Read the article

• Using Different Networks with Different Proxy Servers on Windows 7

  - by John

  Hi, I have a laptop running Windows 7 Professional. There are two wireless networks I connect to every day: Home: no proxy server Work: proxy server with authentication On my iPad and iPhone, I've got two WiFi network profiles (one for home, one for work). The work one has the proxy server settings specified. The home one has no proxy specified. It all works great and I don't need to go changing settings around whenever I move from home to work or vice versa. On my laptop, however, I can't seem to get this going. I can certainly connect to both networks, but when I'm at work I have to go and change the proxy settings (in Internet Options) to be able to use the network. When I'm at home, I have to then go and turn them off. It's a small thing, but considering this is something I have to do every day, it's a bit annoying. Is there any way I can make Windows automatically switch proxy settings on or off based on the network I'm connected to? Thanks, John

  Read the article

• Hardware issue, bsod with windows xp irq and strange messages with ubuntu

  - by JP Hellemons

  I have an old Acer T160 and it used to run Windows XP. But I keep getting random BSOD's. I keep seeing IRQ conflicts. I tried to run ubuntu, which runs and keeps running. But sometimes is not responding. Also there are these popups at ubuntu 12.04 that my network cable (which is onboard) is unplugged. But I have no cable in it! and have an usb dongle for wifi. which also seems unstable. have to (auto)reconnect sometimes. So my question is: is it my mobo, power supply or something else? FYI: I had an dvd-rw station which did not open properly, so unplugged the ata and power, als removed the second harddrive. now only have sata harddrive. also removed the extra video card (ati sapphire x1600 pro) so use only onboard video now and still have these issues. EDIT Update: will try with a new PSU (power supply unit of 400watt) the old (factory) one was 300watt. and will use a usb drive which has 12.04 ubuntu on it (made with unetbootin) to format everything and re-install ubuntu. (so also delete mbr partition) will update the day after tomorrow.

  Read the article

• Transcoding media server streaming to the iPhone

  - by pilif

  I have a huge collection of videos in different formats, but with one thing in common: They are not playable on an iPhone (or iPod Touch). Instead of complaining about Apple's IMHO broken world view ("there are no video formats but quicktime and mp4"), I wonder if there's a solution out there that allows streaming these different videos to the iPhone. This means that the source media needs to be transcoded on the fly. I already tried a few solutions out there, but with varying success: PS3 Media Server kind of worked, but only once and only for one single file. TVersity is said to work, but it requires UAC to be disabled and I don't see any need for this. The solution I'm looking for should run on Windows 2008 Server or Linux. I just can't believe that there's nothing out there that would allow me to stream my huge video collection on my iPhone (we're talking Wifi here, not 3G). After looking at the answers provided and after retrying TVersity without much success, I gave Orb another try and while the web interface failed to work for me, the iPhone Application (I tried the free one at first) actually worked flawlessly. And not only that, it also manages to convert the streams on-the-fly, so you don't have to wait for the transcoding process to finish before playback starts. On my 2.26 Ghz MacMini Server, this worked even with 1080p material. For Windows 2008 Server users out there: Remember to install the Desktop Experience Feature in the Server Manager if you intend this to work. Of all the stuff I had a look at, this really provided instant-success - even though I'm now probably sending the contents of my harddrive to orb's central server (sigh)

  Read the article

• Setup windows 2012 AD in Hyper-V for a Test environment

  - by hub

  Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

  Read the article

• Offline productivity

  - by Frank Meulenaar

  On some days I'm commuting 2hs (oneway) in the train. I don't have any mobile internet nor is there always WiFi service in the train. Because of security reasons I can't do any work in the train so I'm trying to work on my geek time. I'm looking for general solutions on how to do this (I'm on FireFox/Windows but I don't think it matters) Email works perfectly with gmail offline. It syncs directly when online and remembers complicated stuff. So far I used the ScrapBook plugin to store an website. It works good, but I have to download my favorite news page every day again - I want it to sync as soon as possible. It would even be more awesome if I could click a page on my desktop and my laptop would sync as soon as it has the chance. (edit: maybe the autosave plugin for scrapbook can do this) Similarily, I use the Downloadhelper plugin to download youtube vids, but I'd like something that automatically downloads videos from a given channel. Any tips are welcome. So far my early morning schedule is: wake up, power on laptop, make coffee, power off laptop and leave within 10 minutes (enough time for GMail to sync) but I can imagine a system where my laptop stays on during the night (or boots before I wake (and makes me coffee :])).

  Read the article

• which vista services can be disabled with impunity?

  - by GwenKillerby

  I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. I've looked at the other questions but they didn't answer me. thanks, Gwen.

  Read the article

• How can I setup OpenVPN with IPv4 and IPv6 using a tap device?

  - by Lekensteyn

  I've managed to setup OpenVPN for full IPv4 connectivity using tap0. Now I want to do the same for IPv6. Addresses and network setup (note that my real prefix is replaced by 2001:db8): 2001:db8::100:0:0/96 my assigned IPv6 range 2001:db8::100:abc:0/112 OpenVPN IPv6 range 2001:db8::100:abc:1 tap0 (on server) (set as gateway on client) 2001:db8::100:abc:2 tap0 (on client) 2001:db8::1:2:3:4 gateway for server Home laptop (tap0: 2001:db8::100:abc:2/112 gateway 2001:db8::100:abc:1/112) | | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | | router | | OpenVPN INTERNET | eth0 | /tap0 VPS (eth0:2001:db8::1:2:3:4/64 gateway 2001:db8::1) (tap0: 2001:db8::100:abc:1/112) (running Debian 6; OpenVPN 2.1.3-2) The server has both native IPv4 and IPv6 connectivity, the client has only IPv4. I can ping6 to and from my server over OpenVPN, but not to other machines (for example, ipv6.google.com). net.ipv6.conf.all.forwarding is set to 1, I've tried disabling net.ipv6.conf.all.accept_ra as well, without luck. Using tcpdump on both the server and client, I can see that packets are actually transferred over tap0 to eth0. The router (2001:db8::1) send a neighbor solicitation for the client (2001:db8::100:abc:2) to eth0 after it receives the ICMP6 echo-request. The server does not respond to that solicitation, which causes the ICMP6 echo-request not be routed to the destination. How can I make this IPv6 connection work?

  Read the article

< Previous Page | 75 76 77 78 79 80 81 82 83 84 85 86  | Next Page >