Search Results

Search found 39497 results on 1580 pages for 'two shoes'.

Page 725/1580 | < Previous Page | 721 722 723 724 725 726 727 728 729 730 731 732  | Next Page >

• Resize underlying partitions in mdadm RAID1

  - by kyork

  I have a home built NAS, and I need to slightly reconfigure some of my drive usage. I have an mdadm RAID1 composed of two 3TB drives. Each drive has one ext3 partition that uses the entire drive. I need to shrink the ext3 partition on both drives, and add a second 8GB or so ext3 partition to one, and swap partition of equal size to the other. I think I have the steps figured out, but wanted some confirmation. Resize the mdadm RAID resize2fs /dev/md0 [size] where size is a little larger than the currently used space on the drive Remove one of the drives from the RAID mdadm /dev/md0 --fail /dev/sda1 Resize the removed drive with parted Add the new partition to the drive with parted Restore the drive to the RAID mdadm -a /dev/md0 /dev/sda1 Repeat 2-5 for the other device Resize the RAID to use the full partition mdadm --grow /dev/md0 -z max Is there anything I've missed, or haven't considered?

  Read the article

• Trying to administer network setting of server via netsh

  - by Jaime

  Hi there, I am trying to configure the LAN settings of a Windows 2008 server remotely via netsh. I've been trying this command (issued at the client) assuming the IP address of the server is 192.168.0.1: netsh -r 192.168.0.1 -u 192.168.0.1\Administrator -p password lan show config but I keep getting the following message: WARNING: Could not obtain host information from machine [192.168.0.1]. Some commands may not be available. The RPC server is unavailable. Am I understanding the command above properly? Is there a step or two that I missed in setting this up? Thanks in advance. P.S. The Routing and Remove Access service on the server is enabled.

  Read the article

• qemu command not running directly

  - by Dr. Death

  Can I use "qemu://localhost/system " command directly inplace of "virsh -c qemu://localhost/system " command if my both machines are physically connected in a network as virsh will simply creating the virtual shell between two systems? can I use ssh in place of virtual shell here? I tried this but system gives no directory or file name for qemu even when i had qemu installed properly in my system. but when i use virsh i did not get such errors. Do i need to open any unix socket for doing this?

  Read the article

• Duplicate of Certificate Templates does not appear in Certificate Template to Issue

  - by Sean

  I'm following what should be simple instructions to enable LDAP SSL on our domain controller (instructions here). Duplicating the Kerberos certificate is successful however, when attempting to select "Certificate Template to Issue", the created certificate does not appear. What gives? A long time ago, I actually completed this step on a now decommissioned DC with no problem. Our environment is Windows Server 2008 Standard, and we have two domain controllers. Only one has the role of certificate authority. I look forward to any help here, thank you ahead of time.

  Read the article

• IP route ppp0 + eth0 access to outside network

  - by Vitor

  I need some help in define a route I have two connections one from eth0 and other a ppp0 (a 3G card) Not having the ppp0 connection active my route table is: Destination Gateway Genmask Flags Metric Ref Use Iface default DD-WRT 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 I can access my webserver from an outside network through ethernet interface Than I have also my ppp0 3G connection active havig the following route table: D estination Gateway Genmask Flags Metric Ref Use Iface default 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0 10.64.64.64 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 Now I only can access my webserver in outside networks through the IP of the 3G connection Note that my server is serving at 0.0.0.0 IP (to all interfaces) But I need to get access to webserver to both interfaces ethernet and 3G connection I only can have access to both connection in local network Any help to configure this network to have both interfaces with outside networks access is welcome Can anyone give me an example to configure this network with 2 gateways to give outside networks access One for IP 192.168.1.149 and other for the ppp0 IP 89.214.60.196 Tanks

  Read the article

• Error in using DBAN on HDD

  - by John Watson

  I am using DBAN to erase HDD. DBAN is loaded from a CD and BIOS Boot order has been set to favour CD drive. On starting laptop, system boots from CD and DBAN interface can be seen. DBAN detects two storage devices, HDD and the SD Card. My HDD IS 320GB but DBAN says 298GB. It erases the SD card but when i try to erase HDD, it gives following error. DBAN finished with non-fatal errors. *ERROR /dev/sdb (process crash) *ERROR /dev/sda (process crash)

  Read the article

• Can't start my Windows XP Virtual Machine: Insufficient Disk Space

  - by Rob

  Okay, I currently have a server with two virtual machines installed on it, a CentOS5.4 and a Windows XP. I was remote desktopping the Windows XP chatting on IRC, and all of a sudden I lost connection. I checked with my HyperVisor and tried to restart it, and it won't start at all. It's giving me this error: Message from server0297.serverpool.gnet.ba: Failed to extend swap file (fileHandle 16414) from 0 KB to 524288 KB: No space left on device. Could not power on VM : No space left on device. Failed to power on VM info 4/17/2010 9:49:20 PM root Basically I bought the set up from a host, he installed the HyperVisor and the VirtualMachines, and honestly I don't really know what I'm doing. I've looked at some of the settings, and I can't figure it out. If you need any additional information, I'll try to provide it. The CentOS5.4 is still starting and working flawlessly, if that's relevant.

  Read the article

• How to customize Windows Failover clustering to trigger on failure of custom window service?

  - by melaos

  i'm a total newbie on windows failover clustering. and what i want to do now is to setup the FC (failover clustering) on two win 2008 R2 server. and right now i have my custom window service running on both machine. But they cannot run concurrently as it will mess up the DB, thus i just want one to be available at all time (high availability). so i'm wondering if there's any way to set the failover policy to include this custom window service that i've installed on these machines so that if this service goes down or die, then it will automatically trigger the failover to the second node. is this possible? or must it be done programatically? and if so what is the best way? thanks ~m

  Read the article

• Looking for the best ec2 setup for 3 sites totaling in 1.5 mil in traffic monthly

  - by john h.

  I am looking to consolidate our current aws setup of 2 Large ubuntu ec2 servers and 2 large RDS server for our 3 websites that have a total of about 1.5 million hits a month and increasing every month with the majority of traffic (1 mil) to one forum site in the group and the rest of traffic to an ecommerce site and a small wordpress site. So here is my question/thought? Would it be better for us to combine the two ec2 large servers to just one and same with the 2 RDS servers so we run all three sites off one large ec2 and one RDS. -or- Should we setup maybe 2-3 smaller ec2 servers load balenced and a single RDS. -or- Something completely different setup? One concern is that if one site crashes it takes with it the others. It happened in the past but I am pretty sure its because of the forum software and not the server setup. -john

  Read the article

• Using the option port on my Watchguard Firebox as a 2nd gateway exit point?

  - by Donovan

  I'm working on a network project in witch I have to design our network to provide two different exit points. The points are differentiated by the path through the corporate network. One of them travels through some monitoring hardware the other does not. We have a Watchguard Firebox in use as our gateway. Currently the network side provides the unmonitored exit point. I was wondering if i hooked the option port to our lan at a point that would force traffic through the monitored path, would it cause any problems? Access to the unmonitored gateway port would be restricted by ip. That would force all others not authorized to point to the monitored gateway port. I thought with the above design i might be able to get away with not having to buy another firebox to achieve the design I want. Thanks, D

  Read the article

• Automatically save/download e-mail body to disk

  - by CatamountJack

  Is there a program that will allow me to connect to my mail server (IMAP) and automatically save certain new e-mails to disk? Multiple times a day I receive automated e-mail updates about pending jobs from a system that processes some information for us. The data in these e-mails is written as plain-text within the body of the message. I would like to download the newest message, parse it, and display it on my desktop. The last two parts I can manage ok - it's just the automatic downloading that is posing a challenge. I don't use Outlook (I do use Thunderbird), but would prefer not to have the client open to make this happen. I'm currently running Win7.

  Read the article

• trouble backing up large mysql database

  - by Patrick

  I have a wordpress MU database with something like 10,000+ tables for various user's blogs. I need to upgrade wordpress MU to newest version, but want to backup the DB before hand. PHPMyAdmin fails to even load the page when i click export. Ive tried going into the server (windows) and using dos command line: mysqldump -u USERNAME -p PASSWORD> BACKUP.sql but it hangs for a minute and gives me the error: error 23: out of resources when opinging file '.\USERNAME\wp_1037_links.MYD' (Errorcode: 24) when using LOCK Tables What am i doing wrong, or should i be doing? Is PHPMyAdmin right for something this size? Is there a better way of doing this than the two methods i tried? **Note that this is not my site, so any suggestions as to the setup of the DB ill have to run by the owner. Im just here for WP related crap, this is kind of out of scope for what i was brought on to do.

  Read the article

• Server with 3 public IP and iptables

  - by Juan

  I have a linux box with two NIC cards: eth0 and eth1. In one card i have 3 public IP: eth0 = 10.10.10.1, eth0:1= 10.10.10.2 and eth0:2= 10.10.10.3 In the other card i have one local IP eth1 = 192.9.200.1 I want to redirect all the wan traffic for 10.10.10.2 to the LAN 192.9.200.2 and the same for 10.10.10.3 to 192.9.200.3 I have tried with this rule but doesn't work iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.2 -j DNAT --to-destination 192.9.200.2 iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.3 -j DNAT --to-destination 192.9.200.3 IP forward is enabled in /etc/sysctl.conf Can you help me, please.

  Read the article

• HDD vanished after wakeup from standby

  - by Sam

  In my computer I got two hard drives: One 80GB Intel X25 Postville SSD for the system and a 1,5TB Sata HDD for data. When I put the system into standby, and wake it up again, roundabout 50% of the time the 1,5TB HDD is not found. It just vanished from the system (wreaking havok to all programs running which had open files on it). Even going into the system management and refreshing the drives does not find the lost HDD. There are no messages about this in the event log. After a warm reboot the hdd is found again, just like it should. The system is a Shuttle SP35P2 Pro with 8GB Ram and DualCore CPU, OS is Windows 7 Ultimate. I even set up the OS anew, didn't help. Any ideas what might cause this? How to debug, or maybe even fix it?

  Read the article

• Route packets from one VPN to another

  - by Mike

  I have two OpenVPN servers (10.8.0.0 and 10.9.0.0) set up on my OpenSUSE server. Within one network, each computer is visible to any other one, but I'd like to make it so that computers are visible across networks. I'd like to route the packets like this: when a user (say 10.8.0.6) pings an address on the other VPN (10.9.0.6), the packets are routed to the 10.9.0.1 and then to the appropriate computer in this VPN. How do I achieve this using iptables or a different tool? I tried the commands at the end of this section with no avail.

  Read the article

• What resolution can the eeePC 1001HA/1101HA handle with an external monitor plugged in?

  - by Marco Demaio

  I would like to buy a new Eee PC 1001HA or 1101HA. I know the max display resolution is: 1024x600 for eeePC 1001 1366x768 for eeePC 1101 But what's the maximum resolution of the graphic board when connecting these two computers to an external LCD monitor? Let's say the external monitor supports a full HD resolution of 1920x1080. Are these eeePC graphic boards able to go up to such resolution? It's really incredible to me how such a useful piece of information is missing everywhere on every ASUS website. EeePCs are very well suited to be connected to external monitor, so I can't believe how difficult is to find out this information. I downloaded the manual, but it's not in there either. So I'm hoping somone has got one and knows the answer.

  Read the article

• Enabling publickey authentication for server's sshd

  - by aaron

  I have two servers running RHEL 5. Both have nearly identical configurations. I have set up RSA Publickey authetication on both, and one works but the other does not: [my_user@client] $ ssh my_user@server1 --- server1 MOTD Banner --- [my_user@server1] $ and on the other server: [my_user@client] $ ssh my_user@server2 my_user@server2's password: --- server2 MOTD Banner --- [my_user@server2] $ server2's /etc/ssh/sshd_config file snippet: RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys When I run ssh -vvv I get the following snippet: debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug3: Next authentication method: publickey debug1: Offering public key: /home/my_user/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentication that can continue: publickey,gssapi-with-mic,passowrd debug1: Offering public key: /home/my_user/.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentication that can continue: publickey,gssapi-with-mic,passowrd debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password my_user@server2's password:

  Read the article

• ICMP - TTL - Trace Route

  - by dbasnett

  I asked this question at Stack Overflow and then thought this may be the better place to ask. Given the following situation: PC --- |aa RTR1 bb| --- |aa RTR2 bb| --- |aa RTR3 bb| etc Each of the |aa rtr bb| is meant to be a router with two ports aa and bb. My question is this. When you do a trace route from PC which router port address should respond with time to live exceeded in transit message? I seem to remember being taught to think of the router as being in as many parts as ports, so that in my scenario when aa is forwarding the packet to bb and decrements the ttl to 0, it will be the address of the aa port in the failure message. I am trying to find the definitive answer. Thanks.

  Read the article

• how connect to local mysql server (LAN)

  - by clarkk

  I got two Debian 6 servers - one for web and one for the database.. How can I connect through the local area network? On both servers I have permanently changed the hostnames /etc/hostname /etc/hosts web => web-server db => db-server In the privileges in mysql I have set the root user to accept requests from web-server (instead of localhost) and from the web-server I connect to db-server in my.cnf I have escaped the following line: # bind-address = 127.0.0.1 error Warning: mysqli::mysqli(): (HY000/2005): Unknown MySQL server host 'db-server' (1)

  Read the article

• How to easily upgrade MySQL 5.0.32 to MySQL 5.1.20 or higher on Debian Etch?

  - by Ferdy

  I have a home server running Debian Etch with MySQL 5.0.32 on it. I'm not much of a Linux administrator but two years ago I installed the server and it runs fine. I used the official MySQL package for Debian at that time. Since then I have been happily making use of it. Now I need to use a MySQL function that is only available in MySQL 5.1.20 and higher. Therefore I would like to upgrade. I'm not that confident in messing with something I need every day so I wanted to check with you what the best upgrade path would be? Obviously I prefer a simple upgrade that keeps my database, users and settings in place as they are now.

  Read the article

• Munin "Disk usage" is too high?

  - by f-aminov

  I've recently installed munin on my VMware client server and saw that the Disk usage shows about 80-90%. Everything else (cpu load, ram, etc.) seems to be running fine. I have only two virtual hosts on my server with 1000 users/day in total, so I don't think that's too much. Here is the graph for the disk usage. Server info: Debian Lenny, CPU 510Mhz, RAM 512MB Is it bad? What could possibly cause this? Thank you for any suggestions.

  Read the article

• Snippets between desktop and laptop

  - by Jamie F

  The Situation: At work, I have a nice beefy desktop running Windows Server 2008 R2 (SharePoint dev machine). My handy ThinkPad is right next to it. Every once in a while I'd like to cut and paste or share something (usually text) between the machines: for example, I might be headed out and I'd like to take send the URL I'm reading from the desktop to the laptop. Of course I can create a share or use the Admin shares and create files to get stuff back and forth, but that seems heavyweight for what I'm thinking of. I'm thinking more along the lines of sending myself an IM. How do you get little things from machine to machine? Keep a shared folder pinned to the taskbar? Send an email to yourself? Bookmark sync? While on it, I'm looking for a decent multiple clipboard handler: maybe these two functions are combined in some nice little utility? I suspect I'm missing something simple here... Thanks... Jamie F.

  Read the article

• Can /etc/hosts.deny/allow be overridden?

  - by Tar

  I have security measures put in place to keep unwanted users out of my server. I've changed the SSH port, disabled root login, have a software firewall to block portscans, and have entries in hosts.deny and hosts.allow. I have various services denied to all but another server of mine should my IP change, and two other administrators + my own IP address. My question is, can hosts.deny/allow configuration be overridden so that they can gain access to my server? Does using chroot jail for running things like an IRC server and Teamspeak server prevent people from gaining access to my server and screwing with it?

  Read the article

• After installing Meld on 32-bit Karmic on 64-bit machine: "Meld requires pygtk 2.8.0 or higher."

  - by Lynx

  I got this error after installing Meld on a new Karmic installation: ~$ meld No module named pygtk Meld requires pygtk 2.8.0 or higher. I installed the latest version of python-gtk with aptitude but I'm not sure what version is actually installed. My python version is 2.6. This is weird because I have another machine that runs Karmic and Meld without a problem. The only difference between the two machines is the one with the error is a 64-bit machine running a 32-bit installation of Karmic. Could that be the problem?

  Read the article

• Turnkeylinux lampp guest doesn't have internet connection

  - by dave08

  I've set up a turnkeylinux lampp server in virtualbox with two network bridged connections, one for when I'm plugged in to my router, and one for when I'm using a wireless connection. This allowed me to pull up the turnkey control panel on the host machine's browser, but when I try going into the command prompt in the guest and run an apt-get update, it doesn't seem to have an internet connection, even though it seems to have a connection with the host. What could be wrong? Thank you very much in advance for any answers...!

  Read the article

< Previous Page | 721 722 723 724 725 726 727 728 729 730 731 732  | Next Page >