Search Results

Search found 8013 results on 321 pages for 'clean urls'.

Page 73/321 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Fibre channel long distance woes

  - by Marki

  I need a fresh pair of eyes. We're using a 15km fibre optic line across which fibrechannel and 10GbE is multiplexed (passive optical CWDM). For FC we have long distance lasers suitable up to 40km (Skylane SFCxx0404F0D). The multiplexer is limited by the SFPs which can do max. 4Gb fibrechannel. The FC switch is a Brocade 5000 series. The respective wavelengths are 1550,1570,1590 and 1610nm for FC and 1530nm for 10GbE. The problem is the 4GbFC fabrics are almost never clean. Sometimes they are for a while even with a lot of traffic on them. Then they may suddenly start producing errors (RX CRC, RX encoding, RX disparity, ...) even with only marginal traffic on them. I am attaching some error and traffic graphs. Errors are currently in the order of 50-100 errors per 5 minutes when with 1Gb/s traffic. Optics Here is the power output of one port summarized (collected using sfpshow on different switches) SITE-A units=uW (microwatt) SITE-B ********************************************** FAB1 SW1 TX 1234.3 RX 49.1 SW3 1550nm (ko) RX 95.2 TX 1175.6 FAB2 SW2 TX 1422.0 RX 104.6 SW4 1610nm (ok) RX 54.3 TX 1468.4 What I find curious at this point is the asymmetry in the power levels. While SW2 transmits with 1422uW which SW4 receives with 104uW, SW2 only receives the SW4 signal with similar original power only with 54uW. Vice versa for SW1-3. Anyway the SFPs have RX sensitivity down to -18dBm (ca. 20uW) so in any case it should be fine... But nothing is. Some SFPs have been diagnosed as malfunctioning by the manufacturer (the 1550nm ones shown above with "ko"). The 1610nm ones apparently are ok, they have been tested using a traffic generator. The leased line has also been tested more than once. All is within tolerances. I'm awaiting the replacements but for some reason I don't believe it will make things better as the apparently good ones don't produce ZERO errors either. Earlier there was active equipment involved (some kind of 4GFC retimer) before putting the signal on the line. No idea why. That equipment was eliminated because of the problems so we now only have: the long distance laser in the switch, (new) 10m LC-SC monomode cable to the mux (for each fabric), the leased line, the same thing but reversed on the other side of the link. FC switches Here is a port config from the Brocade portcfgshow (it's like that on both sides, obviously) Area Number: 0 Speed Level: 4G Fill Word(On Active) 0(Idle-Idle) Fill Word(Current) 0(Idle-Idle) AL_PA Offset 13: OFF Trunk Port ON Long Distance LS VC Link Init OFF Desired Distance 32 Km Reserved Buffers 70 Locked L_Port OFF Locked G_Port OFF Disabled E_Port OFF Locked E_Port OFF ISL R_RDY Mode OFF RSCN Suppressed OFF Persistent Disable OFF LOS TOV enable OFF NPIV capability ON QOS E_Port OFF Port Auto Disable: OFF Rate Limit OFF EX Port OFF Mirror Port OFF Credit Recovery ON F_Port Buffers OFF Fault Delay: 0(R_A_TOV) NPIV PP Limit: 126 CSCTL mode: OFF Forcing the links to 2GbFC produces no errors, but we bought 4GbFC and we want 4GbFC. I don't know where to look anymore. Any ideas what to try next or how to proceed? If we can't make 4GbFC work reliably I wonder what the people working with 8 or 16 do... I don't assume that "a few errors here and there" are acceptable. Oh and BTW we are in contact with everyone of the manufacturers (FC switch, MUX, SFPs, ...) Except for the SFPs to be changed (some have been changed before) nobody has a clue. Brocade SAN Health says the fabric is ok. MUX, well, it's passive, it's only a prism, nature at it's best. Any shots in the dark? APPENDIX: Answers to your questions @Chopper3: This is the second generation of Brocades exhibiting the problem. Before we had 5000s, now we have 5100s. In the beginning when we still had the active MUX we rented a longdistance laser once to put it into the switch directly in order to make tests for a day, during that day of course it was clean. But as I said, sometimes it's clean just like that. And sometimes it's not. Alternative switches would mean to rebuild the entire SAN with those only to test. Alternative SFPs, well they're hard to come by just like that. @longneck: The line is rented. It's a dark fibre (9um monomode) so there's noone else on it. Sure there are splices. I can't go and look but I have to trust they have been done correctly. As I said the line has been checked and rechecked (using an optical time-domain reflectometer). Obviously you don't have all this equipment yourself because it's way too expensive. @mdpc: What would be the "wrong" type of cable according to you? Up to the switch everything is monomode, yes. The connectors are the correct ones too. Yeah I know there are the green ones where the fibre is cut off at a certain angle etc. But we have the correct ones for all that I know. Progress Report #1 We have had two fabrics (=2x2 switches) with Brocade 5100s with FabricOS 6.4.1 and two fabrics (another 2x4 switches) on FabricOS 7.0.2. On the longdistance ISLs (one in each fabric) it turned out that with FOS 6.4.1 setting it to long distance issues warnings about the VC Init setting and consequently the fill word. But those are only warnings. FOS 7.0.2 requires you to do modifications to VCI and the fillword for long distance links. Setting FOS 6.4.1 to the LS (long-distance static distance) setting with wrong VCI and fillword setting made the whole fabric inoperational (stuck in an SCN loop, use fabriclog -s to see, you don't see it anywhere else, no port error counters or anything increasing). Currently I'm giving the one fabric with the IMHO more correct settings a beating and it seems to do fine, whereas the other one without much traffic still has errors here and there. In short: We have eliminated the active part of the MUX (the FC retimer). We are putting the long distance SFPs into the end equipment themselves. Just to be sure we bought new monomode cables to connect the end equipment to the remaining passive part of the MUX. We are now trying out several long distance configs. It's almost black magic. Everything that happens is mostly empirical, noone seems to have a clue what are the exact reasons to do something. ("We have tried this, and it didn't work, then we tried that and it worked, so we stuck with that." But noone really seems to know why.) I'll keep you updated. Progress Report #2 We got the new lasers for one of the fabrics on warranty. It's ultra clean even on 4GbFC. They're transmitting with roughly 2mW (3dBm) whereas the others are only at 1.5mW (1.5dBm) although that should really be enough. The other fabric (where the lasers are apparently ok) still produces one or two CRCs infrequently. Using sfpshow the SFP producing the actual RX errors shows Status/Ctrl: 0x82 Alarm flags[0,1] = 0x5, 0x40 Warn Flags[0,1] = 0x5, 0x40 Now I'll have to find out what that means. Not sure if it was there before. Well I'll first clear my head with a week of vacation. 8-)

  Read the article

• DataAdapter SelectCommand that excludes current DataTable rows

  - by MC.

  Is there a clean method of creating a DataAdapter SelectCommand to select rows from the database that are not already present in the DataTable?

  Read the article

• Make: how to force make?

  - by HH

  The command $ make all gives errors such as rm: cannot remove '.lambda': No such file or directory so it stops. How can I force-make? Makefile all: make clean make .lambda make .lambda_t make .activity make .activity_t_lambda clean: rm .lambda .lambda_t .activity .activity_t_lambda .lambda: awk '{printf "%.4f \n", log(2)/log(2.71828183)/$$1}' t_year > .lambda .lambda_t: paste .lambda t_year > .lambda_t .activity: awk '{printf "%.4f \n", $$1*2.71828183^(-$$1*$$2)}' .lambda_t > .activity .activity_t_lambda: paste .activity t_year .lambda | sed -e 's@\t@\t\&\t@g' -e 's@$$@\t\\\\@g' | tee > .activity_t_lambda > ../RESULTS/currentActivity.tex

  Read the article

• List CPAN modules that have been made but not installed

  - by Charles Stewart

  Is there an easy/clean way to do this?

  Read the article

• Refactor/rewrite code or continue?

  - by Dan

  I just completed a complex piece of code. It works to spec, it meets performance requirements etc etc but I feel a bit anxious about it and am considering rewriting and/or refactoring it. Should I do this (spending time that could otherwise be spent on features that users will actually notice)? The reasons I feel anxious about the code are: The class hierarchy is complex and not obvious Some classes don't have a well defined purpose (they do a number of unrelated things) Some classes use others internals (they're declared as friend classes) to bypass the layers of abstraction for performance, but I feel they break encapsulation by doing this Some classes leak implementation details (eg, I changed a map to a hash map earlier and found myself having to modify code in other source files to make the change work) My memory management/pooling system is kinda clunky and less-than transparent They look like excellent reasons to refactor and clean code, aiding future maintenance and extension, but could be quite time consuming. Also, I'll never be perfectly happy with any code I write anyway... So, what does stackoverflow think? Clean code or work on features?

  Read the article

• Can I un-check a group of RadioBottoms inside a group box?

  - by Claire Huang

  radio bottoms inside a group Box will be treated as a group of bottoms. They are mutual exclusive. How can I clean up their check states?? I have several radio bottoms, one of them are checked. How can I "clean" (uncheck) all radio bottoms?? "setChecked" doesn't work within a group, I tried to do following things but failed. My code is as following, radioButtom is inside a groupBox, and I want to unchecked it. The first setChecked does works, but the second one doesn't, the radioBottom doesn't been unchecked MainWindow::MainWindow(QWidget *parent) : QMainWindow(parent), ui(new Ui::MainWindow) { QRadioButton *radioButton; ui->setupUi(this); radioButton->setChecked(true); radioButton->setChecked(false); } Where is the problem in my code?

  Read the article

• Django database caching

  - by hekevintran

  I have a Django form that uses an integer field to lookup a model object by its primary key. The form has a save() method that uses the model object referred to by the integer field. The model's manager's get() method is called twice, once in the clean method and once in the save() method: class MyForm(forms.Form): id_a = fields.IntegerField() def clean_id_a(user_id): id_a = self.cleaned_data['id_a'] try: # here is the first call to get MyModel.objects.get(id=id_a) except User.DoesNotExist: raise ValidationError('Object does not exist') def save(self): id_a = self.cleaned_data['id_a'] # here is the second call to get my_model_object = MyModel.objects.get(id=id_a) # do other stuff I wasn't sure whether this hits the database two times or one time so I returned the object itself in the clean method so that I could avoid a second get() call. Does calling get() hit the database two times? Or is the object cached in the thread? class MyForm(forms.Form): id_a = fields.IntegerField() def clean_id_a(user_id): id_a = self.cleaned_data['id_a'] try: # here is my workaround return MyModel.objects.get(id=id_a) except User.DoesNotExist: raise ValidationError('Object does not exist') def save(self): # looking up the cleaned value returns the model object my_model_object = self.cleaned_data['id_a'] # do other stuff

  Read the article

• jQuery Audio Player

  - by tony noriega

  I was given 2 MP3 files, one that is 4.5Mb and one that is 5.6Mb. I was instructed to have them play on a website i am managing. I have found a nice, clean looking CSS based jQuery audio player. My question is, is this the right solution for files that big? I am not sure if the player preloads the file, or streams it ? (if that is the correct terminology) i dont deal much with audio players and such... this player is from happyworm.com/jquery/jplayer/latest/demo-01.htm is there another approach i shoudl take to get this to play properly? I dont want it to have to buffer, and the visitor to wait, or slow page loading...etc..etc.. i want it to play clean and not affect the visitors session to the site. thanks

  Read the article

• Custom login in Django

  - by alpgs

  Django newbie here. I wrote simplified login form which takes email and password. It works great if both email and password are supplied, but if either is missing i get KeyError exception. According to django documentation this should never happen: By default, each Field class assumes the value is required, so if you pass an empty value -- either None or the empty string ("") -- then clean() will raise a ValidationError exception I tried to write my own validators for fields (clean_email and clean_password), but it doesn't work (ie I get KeyError exception). What am I doing wrong? class LoginForm(forms.Form): email = forms.EmailField(label=_(u'Your email')) password = forms.CharField(widget=forms.PasswordInput, label=_(u'Password')) def clean_email(self): data = self.cleaned_data['email'] if not data: raise forms.ValidationError(_("Please enter email")) return data def clean_password(self): data = self.cleaned_data['password'] if not data: raise forms.ValidationError(_("Please enter your password")) return data def clean(self): try: username = User.objects.get(email__iexact=self.cleaned_data['email']).username except User.DoesNotExist: raise forms.ValidationError(_("No such email registered")) password = self.cleaned_data['password'] self.user = auth.authenticate(username=username, password=password) if self.user is None or not self.user.is_active: raise forms.ValidationError(_("Email or password is incorrect")) return self.cleaned_data

  Read the article

• Actionscript classes to 1 SWC file

  - by Daryl

  I'm using Flash Builder 4 (the version after Flex Builder 3, so very similar to Flex Builder 3) and have a bunch of actionscript classes that I frequently need to reference. I have them in a separate folder/package to keep things clean. I know that it's possible to create a SWC from these actionscript files. My question is how do I do it in Flash Builder 4 or Flex Builder 3. Do I need other tools? My objective is just to use the SWC in the project and keep things clean instead of dragging around all these files.

  Read the article

• Folder cleanup with PowerShell

  - by 280Z28

  I'd like to clean up some directories after my script runs by deleting certain folders and files from the current directory if they exist. Originally, I structured the script like this: if (Test-Path Folder1) { Remove-Item -r Folder1 } if (Test-Path Folder2) { Remove-Item -r Folder2 } if (Test-Path File1) { Remove-Item File1 } Now that I have quite a few items listed in this section, I'd like to clean it up. How can I do so? Side note: The items are cleaned up before the script runs, since they are left over from the previous run in case I need to examine them.

  Read the article

• basic unique ModelForm field for Google App Engine

  - by Alexander Vasiljev

  I do not care about concurrency issues. It is relatively easy to build unique form field: from django import forms class UniqueUserEmailField(forms.CharField): def clean(self, value): self.check_uniqueness(super(UniqueUserEmailField, self).clean(value)) def check_uniqueness(self, value): same_user = users.User.all().filter('email', value).get() if same_user: raise forms.ValidationError('%s already_registered' % value) so one could add users on-the-fly. Editing existing user is tricky. This field would not allow to save user having other user email. At the same time it would not allow to save a user with the same email. What code do you use to put a field with uniqueness check into ModelForm?

  Read the article

• What does the C++ output of the HipHop PHP compiler look like?

  - by Alex R

  Is it clean enough that you can discard the PHP and hand-optimize the C++ code?

  Read the article

• Getting Parent Layout in Qt

  - by Austin

  Hi, quick question. Is there any way to (easily) retrieve the parent layout of a widget in Qt? PS: QObject::parent() won't work, for logical reasons. EDIT: I'm positive the widget has a parent layout, because I added it to a layout earlier in the code. Now, I have many other layouts in the window and while it is possible for me to keep track of them, I just want to know if there is an easy and clean way to get the parent layout. EDIT2: Sorry, "easy and clean" was probably not the best way of putting. I meant using the Qt API. EDIT3: I'm adding the widget to the layout like this: QHBoxLayout* layout = new QHBoxLayout; layout-addWidget(button);

  Read the article

• Change Makefile variable value

  - by paulgray

  Is there a way to reassign Makefile variable value inside of the target body? What I am trying to do is to add some extra flags for debug compilation: %.erl: %.beam $(ERLC) $(ERLFLAGS) -o ebin $< test: clean debug_compile_flag compile compile_test debug_compile: $(ERLCFLAGS) += -DTEST So if I invoke test target I would like to clean up my environment, add some new flags (like -DTEST to the existing ones), compile the whole code once again (first sources, then test modules). I do not want to copy/paste the code for compiling with some new flags set since there is a lot of logic put here and there. Is there some easy way to redefine the variable value so I can reuse the existing code?

  Read the article

• Wordpress custom post_type templates

  - by roman

  We are currently working on a Wordpress page that reuses data from another Application. To keep things clean, but still use most wordpress features, we decided to use custom post_type settings (register_post_type) for this data. Now the Problem is, that while accessing these Posts is no problem, the Permalink's to them fail with 404's. We currently work around this issue by adding an action to the "template_redirect" hook that essentially performs a query_posts for the name and our custom types. If query_posts found something we load our custom post templates with locate_template. Although this is working, it does not look like a clean solution - can anyone here propose a better way to tackle our problems?

  Read the article

• Transform PDF to HTML, keep layout

  - by Tgr

  What methods are there to transform a PDF to HTML? It could be anything - online service, software, library. (Opensource preferred. In the last case, php or python would be preferred.) It has to keep the original layout (including page numbers, footnotes and such), keep the images (combining them to one single background image per page is acceptable) and keep the links. It should preferably output valid XHTML and clean up PDF features such as ligatures, but if there is some post-processing required, I can live with that. Something with a clean, relatively semantic HTML output would be great. The closest one I found was zamzar.org, but it choked on links. (Also, the HTML output is an ugly heap of absolutely positioned divs and needs post-processing because of encoding problems.)

  Read the article

• MySQL Query exceptions

  - by Wayne

  In one page, it should show records that has the following selected month from the drop down menu and it is set in the ?month=March So the query will do this $sql = "SELECT * FROM schedule WHERE month = '" . Clean($_GET['month']) . "' AND finished='0' ORDER BY date ASC"; But it shows records that has a value of 2 in the finished column and I don't want the query to include this. I've tried $sql = "SELECT * FROM schedule WHERE month = '" . Clean($_GET['month']) . "' AND finished='0' OR finished = '1' OR finished = '3' ORDER BY date ASC"; But it shows records on different months when it shouldn't be. So basically I want the record to exclude the records that has the value of 2 in the record that will not be shown in the page.

  Read the article

• Maven profile properties are not "overriding"

  - by Nazar

  I have Maven multi-module project with such structure: parent-pom-project -- module1 -- module2 At the parent-pom-project I have such pom.xml <modules> <module>module1</module> </modules> ... <profiles> <profile> <id>local</id> <properties> <prop>local_prop</prop> </properties> </profile> <profile> <id>test</id> <modules> <module>module2</module> </modules> <properties> <prop>test_prop</prop> </properties> </profile> </profiles> At all pom.xml files I have such tag: <build> <resources> <resource> <directory>src/main/resources</directory> <filtering>true</filtering> </resource> <resource> <directory>src/test/resources</directory> <filtering>true</filtering> </resource> </resources> </build> At module1 and module2 in resource directory I have properties files with such text: prop=${prop} The problem is that after mvn clean install or mvn clean install -Ptest or even mvn clean install -P test I get prop=local_prop If I user test profile for build module2 is also builded, but properties are used from local profile. I use Maven 3.0.3. Anybody have any ideas?

  Read the article

• Is there an API for listing queues and exchanges on RabbitMQ?

  - by parsenome

  I've looked quite a bit, but I haven't been able to find a good programmatic way to list the queues on a RabbitMQ server. This is important because I need to clean up my queues and exchanges when I'm done with them. I don't always have a good "done" event that can be used to trigger a cleanup, so I'd like to do it with more of a garbage collection model. If I can list the queues, I can verify that the objects that they're related to shouldn't be producing more entries and clean them up. I know I can use rabbitmqctl to do it, but that needs elevated privileges. Since I haven't been able to find a way to list the queues programmatically, I've been keeping a list of names in the database. That works, but it's ugly.

  Read the article

• Attaching events to Session OnStart and OnEnd using HttpModules

  - by cbp

  Does anyone know a clean way of adding events to Session's OnStart and OnEnd events using an HttpModule (without touching the Global.asax file)?

  Read the article

• stop script debug error dialogs occur in ie8 ?

  - by Haroldo

  I get this, clicking 'no' means the page displays flawlessly. it's refering to this part of jquery1.4.2.js: // Get the Nth element in the matched element set OR // Get the whole matched element set as a clean array get: function( num ) { return num == null ? // Return a 'clean' array this.toArray() : // Return just the object ( num < 0 ? this.slice(num)[ 0 ] : this[ num ] ); }, I assume i'm calling something in the wrong context somewhere in one of my js files (which would be a real mission to find). Will standard IE8 users get this error? (i imagine ms make it pretty difficult to reinstall ie!)

  Read the article

• Dependency Injection -Colloquial explanation

  - by nettguy

  Recently I was asked to express the DI in colloquial explanation. I answered : 1) I am going to a hotel.I ordered food.The hotel management asks me to clean the plates and clean the tables.So here i am a client,I am responsible for managing the service (Instantiating,executing,disposing).But DI decouples such tasks so the service consumer no need not worry about controlling the life cycle of the service. 2) He also asked is there any microsoft API follows DI ?.I answered (This was my guess) In WCF you can create a Proxy using ChannelFactory that controls the life time of your factory. for item (1) he said only 10% is correct for item(2) he said that is factory pattern not dependency injection. Actually what went wrong in my explanation (apart from my bad English) ? What is the real answers for those? I am waiting for your valuable suggestions.

  Read the article

• mod rewrite, title slugs and htaccess

  - by chris

  I have been taken in to provide some seo guidance on a website which has been running since 2005. My problem is i want to use clean urls. The code that handles the url is hidden away in some class file.. and with over a few thousand lines of code its a struggle to rewrite it. So I'm think, I have gone through all the products and created a slug for them as a field in the product table. Is it possible to do something like an intermediate file for htaccess. Some thing like 1./clean-slug-comes-in/ 2.htaccess catches this and uses slug.php to find the relevant product id for the slug. 3.Then product.php?id=(ID.found.from.2) is loaded?

  Read the article

• Where to place a query that should be included in all or most views

  - by Andrew

  In my application I have a sidebar which I want to include a list of pages. Cheating on the MVC setup, I can pretty easily display this as follows (in HAML): # layouts/_sidebar.html.haml %h4 Pages %ul.pages - for page in Page.all %li= link_to page.title, page Now, this works just fine, but clearly it's against the convention. The problem is, this shared layout partial is present in most (but not all) views, and therefore to serve the pages from the controller layer would mean needing to inject an instance variable into almost every controller action in the application. That isn't very clean or DRY. So, how would you handle this kind of situation? Is there a clean, DRY place to put this kind of a simple query that respects Rails MVC convention better?

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >