Search Results

Search found 74454 results on 2979 pages for 'hardware problem'.

Page 73/2979 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• What is this Cable for? 4 Pin to 2 Pin from Riser to Perc in Dell R410

  - by Kyle Brandt

  I got a new raid card for a R410 server since the S300 that came with it doesn't support raid with Linux (No work around for this if SAS from what I could find). Anyways, the RAID card has 2 pins on it and there is a cable that that connects to a 4 pin connection on the riser. The cable only has two wires, one black and one red. What is this cable for? My guess would be maybe LED status for the front panel or something like that, but I am just guessing....

  Read the article

• Can enabling a RAID controller's writeback cache harm overall performance?

  - by Nathan O'Sullivan

  I have an 8 drive RAID 10 setup connected to an Adaptec 5805Z, running Centos 5.5 and deadline scheduler. A basic dd read test shows 400mb/sec, and a basic dd write test shows about the same. When I run the two simultaneously, I see the read speed drop to ~5mb/sec while the write speed stays at more or less the same 400mb/sec. The output of iostat -x as you would expect, shows that very few read transactions are being executed while the disk is bombarded with writes. If i turn the controller's writeback cache off, I dont see a 50:50 split but I do see a marked improvement, somewhere around 100mb/s reads and 300mb/s writes. I've also found if I lower the nr_requests setting on the drive's queue (somewhere around 8 seems optimal) I can end up with 150mb/sec reads and 150mb/sec writes; ie. a reduction in total throughput but certainly more suitable for my workload. Is this a real phenomenon? Or is my synthetic test too simplistic? The reason this could happen seems clear enough, when the scheduler switches from reads to writes, it can run heaps of write requests because they all just land in the controllers cache but must be carried out at some point. I would guess the actual disk writes are occuring when the scheduler starts trying to perform reads again, resulting in very few read requests being executed. This seems a reasonable explanation, but it also seems like a massive drawback to using writeback cache on an system with non-trivial write loads. I've been searching for discussions around this all afternoon and found nothing. What am I missing?

  Read the article

• What is the difference between these Pentium Extreme Edition CPUs?

  - by Giffyguy

  The CPU in question is the Pentium Extreme Edition 955. Intel's website shows four "versions", but for the most part they all look identical. They even share the same set of ordering codes. But one of them has a substantially lower TDP, which is seemingly unexplainable - since everything else is the same. Two of them say "LGA775, Tray" and I have no idea what "Tray" means either. Also, two of them have a different SPEC code. What I need to know is: What does "LGA775, Tray" mean? Why does the one CPU have a lower TDP? And what does that mean for me? Does that mean lower maximum power consumption? Does it mean the CPU may be more stable/endurant, because of a lower heat output? Why do two of them have a different SPEC code, and what does this mean? Finally, what does PLGA775 (as opposed to LGA775) mean, and do I need to be worried about that? Information from Intel's wbsite: Intel® Pentium® Processor Extreme Edition 955 (4M Cache, 3.46 GHz, 1066 MHz FSB) with SPEC Code 1 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 95 Watts BX80553955 SL94N 2 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL94N 3 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 130 Watts BX80553955 SL8WM 4 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL8WM

  Read the article

• Instructions per cycle?

  - by Matt Simmons

  I've been learning a little bit more about how processors work, but I haven't been able to find a straight answer about instructions per cycle. For instance, I was under the impression that a four core CPU could execute four instructions per cycle, so a four core CPU running at 2Ghz would execute 8 billion operations per second. Is this the case? I'm sure it's oversimplifying things, but if there's a guide or something else I can use to set myself straight, I'm definitely open to ideas.

  Read the article

• ImgBurn CD/DVD burn error

  - by bobby

  I am getting the above error when I try to burn a CD/DVD on my DVD writer. I am seeing this error for every CD/DVD I try to burn. I am not able to write any CDs or DVDs using ImgBurn. What could be causing this error?

  Read the article

• Is this a normal operating temperature range for a New Third-Generation MacBook Air (2.13 MHz, 120 G

  - by doug

  Even with just my text editor open (no web browser) and maybe the terminal, the baseline temperature is usually above 40 C. When i open 4-5 browser tabs in Safari (even if none of Sites have Flash) the temp can quickly go over 50 C. (In addition, i am observing these temps even though i have turned the fan up to 3000 rpms). (i have install smcFanControl on my MBA so i can see the temp in the menu bar.) So this means my MBA is running much warmer than my MBP; and in practice, it means that i have to be very careful how i use my MBA. Of course if i load a Site with Flash, it just freaks out, and often quickly goes above 65 C (I've installed a flash blocker to avoid this). Is anyone else observing this behavior? I have checked the Apple boards and sure enough, there are a lot of complaints, but nothing from Apple.

  Read the article

• How to Use 3 Monitors

  - by The.Anti.9

  Right now my setup has a nice big 24" flatscreen in the center, and a 19" flatscreen to the left. And a big gaping hole on the right. I have a 3rd monitor to put there, but I'm not sure how to get the computer to recognize it. Do I need a graphics card with 3 ports? Or can I span the monitors over non SLI-Linked graphics cards? Is it possible to plug my 3rd monitor into the on-board VGA port and have it work?

  Read the article

• HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

  - by JohnRB

  I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

  Read the article

• Looking for a good computer repair kit

  - by johnny

  I'm afraid I'll get ripped if I get the generic kit from Tigerdirect or whatever. For clarity this is not software I am after but physical tools. It should include something for occassional soldering of electronics, crimper, other things I cannot remember. Hoping for ideas or product links (yes I am searching also). Thank you.

  Read the article

• Hiding monitor from windows, working with it from my app only [closed]

  - by Mikhail

  I need to use a monitor as a "private" device for my special application, I want to use it as a flashlight of a sort and draw special patterns on it in full screen. I don't want this monitor to be recognized by OS (Windows 7) as a monitor. I.e. user should not be able to move mouse to that monitor, or change its resolution, or run screensaver on it or whatever. But I want to be able to interact with it from my application. Monitor is plugged using an HDMI cable to a video card (most probably nVidia). What is the simplest way to do this? All solutions are appreciated, including purchasing additional adapters or simple video cards, or any other special devices.

  Read the article

• Hard drives indication with controller MegaRAID SAS 9261-8i on HP Proliant DL320e Gen8. Is it possible?

  - by ame

  Give me advice, please. My situation: There're the server HP ProLiant DL320e Gen8 and MegaRAID SAS 9261-8i RAID Controller. I installed Controller into server and I reconnected Mini-SAS cord from block of hard drives to controller, but I haven't any indication of hard discs on server front panel. There's indication of activity of drives only during boot of server. Controller has 2-pin connector (JT6B3, SAS Activity LED header) but where and how can I connect it? Thanx.

  Read the article

• Monitor goes black for a few seconds

  - by privatehuff

  I have a Hanns G 28" monitor, Model # HG281D It has its issues (viewing angle sucks) but has been functional and solid, great for desktop stuff. Worked without any sign of any problems for 6-12 months. However, now the monitor "goes black" for about 2-3 seconds, almost like when you click "detect display" It does not turn off (power light does not go amber) The computer is completely unaffected and the video mode never changes when the picture returns. The computer is fully responsive and will keep playing music or taking my keypresses during the time I can't see anything. (it just happened and I kept typing, etc) It happens on multiple computers across several operating systems. (I have an 8-port iogear KVM switch that has several computers connected) But, it seems to happen only on certain computers. I have a hackintosh that does it, a windows 7 PC that does not, a lenovo laptop that does not, and my old ubuntu 8.10 box did not do it, but my new mint 8 box does do it. I've check the connections and tried changing out the power cable and the vga cable. Sometimes it won't happen for hours (or days) and sometimes it happens several times per hour. It was happening many months ago, did not happen for months, and has now started happening again. Does this make any sense? What could it be?

  Read the article

• Restarting an IBM BMC without restarting the server itself

  - by SRobertJames

  I have a few servers with IBM BMC (Baseboard Management Controller). I'd like to power cycle the BMC without restarting the server. Is this possible? How? Note: On one of them, the web interface is down; so I'd need to either do this by physically restarting the BMC (not sure how to do this - even the power button on the server isn't supposed to recycle the BMC, I believe) or via the UDP or SNMP interface (again, not sure how to do that either)

  Read the article

• Adding extra fan on my setup. please advice on proper Exhaust or Intake of Fan.

  - by Pennf0lio

  Hi, I modify my Computer case so that I can add more computer fan to make my computer cool this summer. I would need your thoughts how I can improve my idea and I'm open to all of your advices. Status: Fan Position (The blue circles are the fan's location) At the side I have to intake blowing fresh air at the motherboard and at the top and back I have Exhaust fan blowing out hot air. The computer fans will be powered by 12v adapter (recycled) so that my power supply wouldn't be overloaded. I need a practical advice, I don't want to spend to much on this. Thanks.

  Read the article

• How do I clean dust from a computer?

  - by Jonas

  As computers become faster and generate more heat it gets more important to have good ventilation, but that also increases the amount of dust sticking to the components of the computer. It's of course better to make sure the computer never gets dusty by vacuum cleaning around it (not in it) frequently. But what to do if it's already to late? I've heard that vacuum cleaning the computer itself is very bad, since it can cause static electricity that hurts the computer. So, Does anyone have any tips for how to remove dust from your computer?

  Read the article

• Scanner Daily Duty Cycle

  - by juanp

  I'm comfused with the concept of 'Daily Duty Cycle'. For example if I have a scanner that the spec is: PPM (pages per minute): 90 and DDC (Daily Duty Cycle): 800. It means that in one day it will be able to scan only 800 pages?

  Read the article

• Scanner Daily Duty Cycle

  - by Juanp

  I'm comfused with the concept of 'Daily Duty Cycle'. For example if I have a scanner that the spec is: PPM (pages per minute): 90 and DDC (Daily Duty Cycle): 800. I am interested in scanning ONLY 10 hours continuously, what would it be the best choice: 90 * 60 * 10 = 54.000 or (800 / 24) * 10 = 333 It is very different results. what would it be the best option?

  Read the article

• Determine Server specs for a Rails with MySQL database (on AWS)

  - by Rogier

  I developed a intranet applications with Rails (3.2) for one of my customers. There will be around 30-40 employees working with it. Backend is MySQL (5). What would be the best way to determine the servers specs needed? Given: max. load will be roughly 2400 (40*60) HTTP requests (mixed GET / POST) per hour. 15% of these calls are JSON calls (iOS) avg request will make between 5-10 database calls 500-800 SQL INSERTS per day webpages are fairly simple (no images, just text) avg webpage is 15 request (css/js/etc) and total size is 35-45 KB More specific, since they need access from multiple geographical locations, we are thinking of running a bitnami Ruby stack in the AWS cloud (uptime is important). Any thoughts on a AWS Instance (small/medium) and Utilization (light/medium/heavy) ? Thanks!

  Read the article

• What is the name of this screw? (from HP ProLiant quick-deploy rail kits)

  - by kockiren

  I need the name of the screw for the HP quick deploy rail kit. The screw clicks into the square holes of the rack. It is a Gen4 Rail kit but the screw is like the Gen8 Rail kit ones. I called HP support, but they couldn't really help me. Unfortunately the rack manual does not name this screw either. After googling a while, I found the compatible "Thumb Style Rack Screws". It would do the job but isn't exactly what I am looking for. So, what is the name of the pictured screw.

  Read the article

• Best motherboard power supply combo for backblaze server

  - by jin14

  Building a backblaze server as described in this article. http://blog.backblaze.com/ So 45 hard drives in one box. I'm making it a MSDPM 2010 server so I actually don't even need raid cards in there as MSDPM will figure out how to use all of the hard drives on it's own. So need to know what motherboard, CPU, power supply I should get. Primary hard drive : SSD 128GB Storage : 45 1.5GB sata drives OS : windows 2008 Backup software : Microsoft System center Data protection server 2010 Need to know Which mother board to buy which will support 45 SATA hard drives. Don't need a raid card. Which power supply can power all 45 hard drives, 1 ssd drive, motherboard. Best set of equipment that meets my needs wins

  Read the article

• Can anyone explain these cpu specs?

  - by Kevin

  Intel® Core™ i7-640M (2.8~3.46GHz, 35W) w/4MB Cache - 2 Cores, 4 Threads - 2.5 GT/s SO i'm buying a new laptop, which i have not done in 6 years. So i am not familiar with any of these cpu specs. It was the highest option for intel for this laptop. So i am assuming it is somewhat fast. But i'd like to learn what these specs mean. Any help would be greatly appreciated. i am not really a computer guy but would love to learn about what I am buying. Thanks!

  Read the article

• What will happen if I (accidentally) pour a bucket of water inside my pc?

  - by ULTRA_POROV

  Is it dangerous? What will happen to me and the PC? Edit: It's a serious question. The other day I almost spilled a bottle of cola inside my PC (the case was open).

  Read the article

• Two Different nVidia Cards, One as Graphics, One as Physics - Possible?

  - by Jasarien

  Hey guys, Soon I will have a brand new Geforce GTX 285 to replace my current 8800GT. Will it be possible to move my 8800GT to another PCIX slot, put the GTX 285 into the primary slot and use the nVidia software to make the 8800GT do physics? I have enough PCIX slots on my motherboard (4). The GTX 285 will take up 2, so the 8800GT should fit in the 3rd. If anyone knows if this is possible, I would be grateful to be educated!

  Read the article

• Computer won't start unless power is removed for ~5 minutes

  - by Paul Tarjan

  I have a fairly standard 2-year old desktop computer (quad-core intel, single hard drive, decent video card, 300W power supply) which recently started acting up. I'm not sure what the cause is, so hopefully you can help. Sometimes (once a week-ish) I press the power button and nothing happens. No blinking, no sounds, no nothing. If I remove the power cord (or flip the switch on the power supply) I hear a capacitor discharge. If I leave it in the "no power at all" state for about 5 minutes then I can put the plug back in and the computer works perfectly. What is the issue? What do you think I have to replace?

  Read the article

• Is it a good idea to have the operating system on a solid state drive?

  - by Kenji Kina

  There is something I don't quite understand. I know a SSD helps with OS load times, but I'm not sure if all this boost is only noticeable/interesting when booting, or gives an all around considerably better experience thereafter. I am interested in having a quick and responsive environment after booting, which leads me to think that it'd be better to spend the SSD capacity in my most used apps (and the page file? Another inside question) and not the OS itself. This, of course, means that I don't know just how much the OS reads/writes its files during normal usage. So, how good an idea is it to dump the whole 20GB+ of Windows 7 OS into the SSD (considering the hefty price per GB of SSD capacity) if I can put up with the usual hard disk boot times? Would I be missing on a lot if I didn't?

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >