Search Results

Search found 19788 results on 792 pages for 'remote host'.

Page 731/792 | < Previous Page | 727 728 729 730 731 732 733 734 735 736 737 738  | Next Page >

  • Intermittent internet connectivity

    - by Rob Oplawar
    UPDATED: I recently built a new computer and set it up to dual-boot Windows 7 and Ubuntu 11.10. In Windows, using the same hardware, my LAN connectivity is solid. In Ubuntu, however, my network interface periodically dies and resets itself; I'll have a solid connection for 30 seconds, and then it will go out for 30 seconds. When I tail the log: tail -f /var/log/kern.log I see "eth0 link up" messages appear periodically, corresponding with the return of connectivity. I posted the original question months ago, and misinterpreted what was going on. With a working Internet connection in Windows, I ignored the problem for some months. See my answer below for the solution (drivers). ORIGINAL POST In Ubuntu, although I maintain a solid connection to my LAN (pinging the router IP address consistently returns a good result), my internet connectivity drops in and out. When I continuously ping 74.125.227.18 (a google.com server), I get responses for a while, then I start getting "Destination Host Unreachable" for a while, then I get responses again. This happens consistently, dropping the connection for about 30 seconds out of every minute or two. Whether I configure my network via the network manager or via /etc/network/interfaces seems to make no difference. I configure with the following settings: address 192.168.1.101 network 192.168.1.0 gateway 192.168.1.99 (my router's IP address) netmask 255.255.255.0 (confirmed as the right netmask for the router) broadcast 192.168.1.255 (also confirmed with the router). ifconfig confirms that these settings are working: eth0 Link encap:Ethernet HWaddr 50:e5:49:40:da:a6 inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe40:daa6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11557 errors:0 dropped:11557 overruns:0 frame:11557 TX packets:13117 errors:0 dropped:211 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9551488 (9.5 MB) TX bytes:1930952 (1.9 MB) Interrupt:41 Base address:0xa000 I get the same issue when I use automatic DHCP address settings, although I did confirm that there is no other machine on the network with the static IP address I want to use. As I said, the connection to the local network stays solid - I never have any trouble pinging 192.168.1.* - it's internet addresses that I intermittently cannot reach. It's not a DNS issue because pinging known IP addresses directly shows the same behavior. Also, I don't think it's a hardware issue, as I never have any internet connectivity problems on the same machine in Windows. The network hardware is built into the motherboard: Gigabyte Z68XP-UD3P. I managed to bring the OS fully up to date, according to the update manager, but it didn't fix the issue, and with my limited understanding of network architecture I'm at my wit's end. The only clue I can see is that ifconfig is reporting a lot of dropped packets, but I'm not sure what to do about it. UPDATE: It seems my problem is a little more generic than I described; now when I try pinging my router and google simultaneously, they both go unreachable at the same time. Running ifdown eth0 and then ifup eth0 brings it back temporarily; if I just wait it comes back after a couple of minutes. I'll broaden my search through intermittent network connectivity problems.

    Read the article

  • Wireless connection works but the internet is too slow to use in Ubuntu 11.04

    - by Garrin
    The internet is so slow as to be unusable. And I'm not being picky. Even after minutes I can't get my Google home page to load. I tried installing a package through apt-get and was getting rates between 0 and a few hundred bytes/s. That's bytes, not kilobytes! Mostly 0 however (no exaggeration, it spends large amounts of time stalled). And I would go to a speed test web site of some kind but I can't since nothing will load. Briefly put, the laptop I am using was connected to two wireless networks while using Ubuntu 11.04 without any issues before this. It was also connected to a wired network without any issues. It dual boats Windows 7 which has never had any issues, not even with the current wireless network. Just to be clear, on the current wi-fi network, Windows 7 encounters no issues (speedtest.net puts the network speed at 1mb/s) but my network connection in Ubuntu 11.04 is so slow as to literally be unusable. I am unfamiliar with the router except for the fact that it boasts a Rogers logo (that's a large ISP/cable provider in Canada for those not familiar with the land of igloos and polar bears). I am far from the router and some desktop widget I use tells me the signal strength is at 58% (it seems fairly reliable and this would appear to match up with the filled bars in the network icon). I should also mention I'm just renting a room in this house so I'm not the network administrator and while I can access the 192.168.0.1 router page, the password wasn't set to 'password' so it's not much use to me. Here are a bunch of commands I ran which don't tell me a whole lot but I thought might be more instructive to the wise around here: lspci (just showing my network card): 05:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) This one is self explanatory. PING www.googele.com (216.65.41.185) 56(84) bytes of data. 64 bytes from nnw.net (216.65.41.185): icmp_req=1 ttl=51 time=267 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=2 ttl=51 time=190 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=3 ttl=51 time=212 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=4 ttl=51 time=207 ms 64 bytes from nnw.net (216.65.41.185): icmp_req=5 ttl=51 time=220 ms --- www.googele.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4003ms rtt min/avg/max/mdev = 190.079/219.699/267.963/26.121 ms ifconfig eth0 Link encap:Ethernet HWaddr 20:6a:8a:02:20:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:960 (960.0 B) TX bytes:960 (960.0 B) wlan0 Link encap:Ethernet HWaddr 20:7c:8f:05:c6:bf inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::227c:8fff:fe05:c6bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:982 errors:0 dropped:0 overruns:0 frame:0 TX packets:658 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:497250 (497.2 KB) TX bytes:95076 (95.0 KB) Thank you

    Read the article

  • Consolidation in a Database Cloud

    - by B R Clouse
    Consolidation of multiple databases onto a shared infrastructure is the next step after Standardization.  The potential consolidation density is a function of the extent to which the infrastructure is shared.  The three models provide increasing degrees of sharing: Server: each database is deployed in a dedicated VM. Hardware is shared, but most of the software infrastructure is not. Standardization is often applied incompletely since operating environments can be moved as-is onto the shared platform. The potential for VM sprawl is an additional downside. Database: multiple database instances are deployed on a shared software / hardware infrastructure. This model is very efficient and easily implemented with the features in the Oracle Database and supporting products. Many customers have moved to this model and achieved significant, measurable benefits. Schema: multiple schemas are deployed within a single database instance. The most efficient model, it places constraints on the environment. Usually this model will be implemented only by customers deploying their own applications.  (Note that a single deployment can combine Database and Schema consolidations.) Customer value: lower costs, better system utilization In this phase of the maturity model, under-utilized hardware can be used to host more workloads, or retired and those workloads migrated to consolidation platforms. Customers benefit from higher utilization of the hardware resources, resulting in reduced data center floor space, and lower power and cooling costs. And, the OpEx savings from Standardization are multiplied, since there are fewer physical components (both hardware and software) to manage. Customer value: higher productivity The OpEx benefits from Standardization are compounded since not only are there fewer types of things to manage, now there are fewer entities to manage. In this phase, customers discover that their IT staff has time to move away from "day-to-day" tasks and start investing in higher value activities. Database users benefit from consolidating onto shared infrastructures by relieving themselves of the requirement to maintain their own dedicated servers. Also, if the shared infrastructure offers capabilities such as High Availability / Disaster Recovery, which are often beyond the budget and skillset of a standalone database environment, then moving to the consolidation platform can provide access to those capabilities, resulting in less downtime. Capabilities / Characteristics In this phase, customers will typically deploy fixed-size clusters and consolidate on a cluster until that cluster is deemed "full," at which point a new cluster is built. Customers will define one or a few cluster architectures that are used wherever possible; occasionally there may be deployments which must be handled as exceptions. The "full" policy may be based on number of databases deployed on the cluster, or observed peak workload, etc. IT will own the provisioning of new databases on a cluster, making the decision of when and where to place new workloads. Resources may be managed dynamically, e.g., as a priority workload increases, it may be given more CPU and memory to handle the spike. Users will be charged at a fixed, relatively coarse level; or in some cases, no charging will be applied. Activities / Tasks Oracle offers several tools to plan a successful consolidation. Real Application Testing (RAT) has a feature to help plan and validate database consolidations. Enterprise Manager 12c's Cloud Management Pack for Database includes a planning module. Looking ahead, customers should start planning for the Services phase by defining the Service Catalog that will be made available for database services.

    Read the article

  • "The connection has timed out" - Please help!

    - by gon
    I recently installed a fresh Ubuntu 12.04 LTS on a desktop, and the installation itself was successful (other than 'grub rescue' issue that I encountered but fixed) but this connection problem is really giving me a headache. Symptoms: 1. When I open the FireFox browser and try to connect to a website, it just hangs for a while saying "Connecting..." but eventually loads an error page "The connection has timed out". 2. It's not a browser problem (and I tried setting ipv6 thing to "true" at about:config) because running "sudo apt-get install [some-random-package]" at terminal fails ("E: Unable to locate package [package]") too. All other operations that need internet access are not working. 3. I certainly see a wired network (called "eth1") at the Network Manager, and it says "Connection Established" after disconnecting and then connecting again. I have tried almost everything that could be found from google search results still no luck. Their problems slightly differ from mine or the solutions just don't work. By the way it didn't have internet access when installing Ubuntu 12.04. (I ignored the message that I need internet to install Ubuntu) Could this be a problem? I'm sorry I don't remember if internet worked or not on the previous version of Ubuntu. :( I would really appreciate your help... I don't even know what more to do if this fails too.. Thanks!! Thanks for your comment. Here is the result of ifconfig: eth0 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b9 inet addr:10.10.65.185 Bcast:10.10.65.255 Mask:255.255.255.0 inet6 addr: fe80::7aac:c0ff:fe3d:b2b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3907 errors:0 dropped:0 overruns:0 frame:0 TX packets:771 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:393118 (393.1 KB) TX bytes:73472 (73.4 KB) Interrupt:16 eth1 Link encap:Ethernet HWaddr 78:ac:c0:3d:b2:b8 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204 (204.0 B) TX bytes:204 (204.0 B) route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.10.65.1 0.0.0.0 UG 0 0 0 eth0 10.10.65.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 /etc/resolv.conf: # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 8.8.8.8 nameserver 8.8.4.4 nameserver 10.81.1.8 nameserver 10.1.2.10 nameserver 127.0.0.1 search yamatake.local /etc/network/interfaces: auto lo iface lo inet loopback #auto eth0 #iface eth0 inet dhcp #auto eth1 #iface eth1 inet dhcp And I'll also include the result of 'sudo lshw -C network' in case it might help: *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 78:ac:c0:3d:b2:b9 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 ip=10.10.65.185 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:93 memory:fc000000-fc00ffff *-network description: Ethernet interface product: NetXtreme BCM5764M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth1 version: 10 serial: 78:ac:c0:3d:b2:b8 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=5764m-v3.35 latency=0 link=no multicast=yes port=twisted pair speed=100Mbit/s resources: irq:94 memory:fb000000-fb00ffff

    Read the article

  • Problem in udp socket programing in c

    - by Md. Talha
    I complile the following C code of UDP client after I run './udpclient localhost 9191' in terminal.I put "Enter Text= " as Hello, but it is showing error in sendto as below: Enter text: hello hello : error in sendto()guest-1SDRJ2@md-K42F:~/Desktop$ " Note: I open 1st the server port as below in other terminal ./server 9191. I beleive there is no error in server code. The udp client is not passing message to server. If I don't use thread , the message is passing .But I have to do it by thread. UDP client Code: /* simple UDP echo client */ #include <sys/types.h> #include <sys/socket.h> #include <netinet/in.h> #include <arpa/inet.h> #include <netdb.h> #include <stdio.h> #include <pthread.h> #define STRLEN 1024 static void *readdata(void *); static void *writedata(void *); int sockfd, n, slen; struct sockaddr_in servaddr; char sendline[STRLEN], recvline[STRLEN]; int main(int argc, char *argv[]) { pthread_t readid,writeid; struct sockaddr_in servaddr; struct hostent *h; if(argc != 3) { printf("Usage: %s <proxy server ip> <port>\n", argv[0]); exit(0); } /* create hostent structure from user entered host name*/ if ( (h = gethostbyname(argv[1])) == NULL) { printf("\n%s: error in gethostbyname()", argv[0]); exit(0); } /* create server address structure */ bzero(&servaddr, sizeof(servaddr)); /* initialize it */ servaddr.sin_family = AF_INET; memcpy((char *) &servaddr.sin_addr.s_addr, h->h_addr_list[0], h->h_length); servaddr.sin_port = htons(atoi(argv[2])); /* get the port number from argv[2]*/ /* create a UDP socket: SOCK_DGRAM */ if ( (sockfd = socket(AF_INET,SOCK_DGRAM, 0)) < 0) { printf("\n%s: error in socket()", argv[0]); exit(0); } pthread_create(&readid,NULL,&readdata,NULL); pthread_create(&writeid,NULL,&writedata,NULL); while(1) { }; close(sockfd); } static void * writedata(void *arg) { /* get user input */ printf("\nEnter text: "); do { if (fgets(sendline, STRLEN, stdin) == NULL) { printf("\n%s: error in fgets()"); exit(0); } /* send a text */ if (sendto(sockfd, sendline, sizeof(sendline), 0, (struct sockaddr *) &servaddr, sizeof(servaddr)) < 0) { printf("\n%s: error in sendto()"); exit(0); } }while(1); } static void * readdata(void *arg) { /* wait for echo */ slen = sizeof(servaddr); if ( (n = recvfrom(sockfd, recvline, STRLEN, 0, (struct sockaddr *) &servaddr, &slen)) < 0) { printf("\n%s: error in recvfrom()"); exit(0); } /* null terminate the string */ recvline[n] = 0; fputs(recvline, stdout); }

    Read the article

  • How to handle multi-processing of libraries which already spawn sub-processes?

    - by exhuma
    I am having some trouble coming up with a good solution to limit sub-processes in a script which uses a multi-processed library and the script itself is also multi-processed. Both, the library and script are modifiable by us. I believe the question is more about design than actual code, but for what it's worth, it's written in Python. The goal of the library is to hide implementation details of various internet routers. For that reason, the library has a "Proxy" factory method which takes the IP of a router as parameter. The factory then probes the device using a set of possible proxies. Usually, there is one proxy which immediately knows that is is able to send commands to this device. All others usually take some time to return (given a timeout). One thought was already to simply query the device for an identifier, and then select the proper proxy using that, but in order to do so, you would already need to know how to query the device. Abstracting this knowledge is one of the main purposes of the library, so that becomes a little bit of a "circular-requirement"/deadlock: To connect to a device, you need to know what proxy to use, and to know what proxy to create, you need to connect to a device. So probing the device is - as we can see - the best solution so far, apart from keeping a lookup-table somewhere. The library currently kills all remaining processes once a valid proxy has been found. And yes, there is always only one good proxy per device. Currently there are about 12 proxies. So if one create a proxy instance using the factory, 12 sub-processes are spawned. So far, this has been really useful and worked very well. But recently someone else wanted to use this library to "broadcast" a command to all devices. So he took the library, and wrote his own multi-processed script. This obviously spawned 12 * n processes where n is the number of IPs to which he broadcasted. This has given us two problems: The host on which the command was executed slowed down to a near halt. Aborting the script with CTRL+C ground the system to a total halt. Not even the hardware console responded anymore! This may be due to some Python strangeness which still needs to be investigated. Maybe related to http://bugs.python.org/issue8296 The big underlying question, is how to design a library which does multi-processing, so other applications which use this library and want to be multi-processed themselves do not run into system limitations. My first thought was to require a pool to be passed to the library, and execute all tasks in that pool. In that way, the person using the library has control over the usage of system resources. But my gut tells me that there must be a better solution. Disclaimer: My experience with multiprocessing is fairly limited. I have implemented a few straightforward which did not require access control to resources. So I have not yet any practical experience with semaphores or mutexes. p.s.: In the future, we may have enough information to do this without the probing. But the database which would contain the proper information is not yet operational. Also, the design about multiprocessing a multiprocessed library intrigues me :)

    Read the article

  • Using Private Extension Galleries in Visual Studio 2012

    - by Jakob Ehn
    Note: The installer and the complete source code is available over at CodePlex at the following location: http://inmetavsgallery.codeplex.com   Extensions and addins are everywhere in the Visual Studio ALM ecosystem! Microsoft releases new cool features in the form of extensions and the list of 3rd party extensions that plug into Visual Studio just keeps growing. One of the nice things about the VSIX extensions is how they are deployed. Microsoft hosts a public Visual Studio Gallery where you can upload extensions and make them available to the rest of the community. Visual Studio checks for updates to the installed extensions when you start Visual Studio, and installing/updating the extensions is fast since it is only a matter of extracting the files within the VSIX package to the local extension folder. But for custom, enterprise-specific extensions, you don’t want to publish them online to the whole world, but you still want an easy way to distribute them to your developers and partners. This is where Private Extension Galleries come into play. In Visual Studio 2012, it is now possible to add custom extensions galleries that can point to any URL, as long as that URL returns the expected content of course (see below).Registering a new gallery in Visual Studio is easy, but there is very little documentation on how to actually host the gallery. Visual Studio galleries uses Atom Feed XML as the protocol for delivering new and updated versions of the extensions. This MSDN page describes how to create a static XML file that returns the information about your extensions. This approach works, but require manual updates of that file every time you want to deploy an update of the extension. Wouldn’t it be nice with a web service that takes care of this for you, that just lets you drop a new version of your VSIX file and have it automatically detect the new version and produce the correct Atom Feed XML? Well search no more, this is exactly what the Inmeta Visual Studio Gallery Service does for you :-) Here you can see that in addition to the standard Online galleries there is an Inmeta Gallery that contains two extensions (our WIX templates and our custom TFS Checkin Policies). These can be installed/updated i the same way as extensions from the public Visual Studio Gallery. Installing the Service Download the installler (Inmeta.VSGalleryService.Install.msi) for the service and run it. The installation is straight forward, just select web site, application pool and (optional) a virtual directory where you want to install the service.   Note: If you want to run it in the web site root, just leave the application name blank Press Next and finish the installer. Open web.config in a text editor and locate the the <applicationSettings> element Edit the following setting values: FeedTitle This is the name that is shown if you browse to the service using a browser. Not used by Visual Studio BaseURI When Visual Studio downloads the extension, it will be given this URI + the name of the extension that you selected. This value should be on the following format: http://SERVER/[VDIR]/gallery/extension/ VSIXAbsolutePath This is the path where you will deploy your extensions. This can be a local folder or a remote share. You just need to make sure that the application pool identity account has read permissions in this folder Save web.config to finish the installation Open a browser and enter the URL to the service. It should show an empty Feed page:   Adding the Private Gallery in Visual Studio 2012 Now you need to add the gallery in Visual Studio. This is very easy and is done as follows: Go to Tools –> Options and select Environment –> Extensions and Updates Press Add to add a new gallery Enter a descriptive name, and add the URL that points to the web site/virtual directory where you installed the service in the previous step   Press OK to save the settings. Deploying an Extension This one is easy: Just drop the file in the designated folder! :-)  If it is a new version of an existing extension, the developers will be notified in the same way as for extensions from the public Visual Studio gallery: I hope that you will find this sever useful, please contact me if you have questions or suggestions for improvements!

    Read the article

  • I.T. Chargeback : Core to Cloud Computing

    - by Anand Akela
    Contributed by Mark McGill Consolidation and Virtualization have been widely adopted over the years to help deliver benefits such as increased server utilization, greater agility and lower cost to the I.T. organization. These are key enablers of cloud, but in themselves they do not provide a complete cloud solution. Building a true enterprise private cloud involves moving from an admin driven world, where the I.T. department is ultimately responsible for the provisioning of servers, databases, middleware and applications, to a world where the consumers of I.T. resources can provision their infrastructure, platforms and even complete application stacks on demand. Switching from an admin-driven provisioning model to a user-driven model creates some challenges. How do you ensure that users provisioning resources will not provision more than they need? How do you encourage users to return resources when they have finished with them so that others can use them? While chargeback has existed as a concept for many years (especially in mainframe environments), it is the move to this self-service model that has created a need for a new breed of chargeback applications for cloud. Enabling self-service without some form of chargeback is like opening a shop where all of the goods are free. A successful chargeback solution will be able to allocate the costs of shared I.T. infrastructure based on the relative consumption by the users. Doing this creates transparency between the I.T. department and the consumers of I.T. When users are able to understand how their consumption translates to cost they are much more likely to be prudent when it comes to their use of I.T. resources. This also gives them control of their I.T. costs, as moderate usage will translate to a lower charge at the end of the month. Implementing Chargeback successfully create a win-win situation for I.T. and the consumers. Chargeback can help to ensure that I.T. resources are used for activities that deliver business value. It also improves the overall utilization of I.T. infrastructure as I.T. resources that are not needed are not left running idle. Enterprise Manager 12c provides an integrated metering and chargeback solution for Enterprise Manager Targets. This solution is built on top of the rich configuration and utilization information already available in Enterprise Manager. It provides metering not just for virtual machines, but also for physical hosts, databases and middleware. Enterprise Manager 12c provides metering based on the utilization and configuration of the following types of Enterprise Manager Target: Oracle VM Host Oracle Database Oracle WebLogic Server Using Enterprise Manager Chargeback, administrators are able to create a set of Charge Plans that are used to attach prices to the various metered resources. These plans can contain fixed costs (eg. $10/month/database), configuration based costs (eg. $10/month if OS is Windows) and utilization based costs (eg. $0.05/GB of Memory/hour) The self-service user provisioning these resources is then able to view a report that details their usage and helps them understand how this usage translates into cost. Armed with this information, the user is able to determine if the resources are delivering adequate business value based on what is being charged. Figure 1: Chargeback in Self-Service Portal Enterprise Manager 12c provides a variety of additional interfaces into this data. The administrator can access summary and trending reports. Summary reports allow the administrator to drill-down through the cost center hierarchy to identify, for example, the top resource consumers across the organization. Figure 2: Charge Summary Report Trending reports can be used for I.T. planning and budgeting as they show utilization and charge trends over a period of time. Figure 3: CPU Trend Report We also provide chargeback reports through BI Publisher. This provides a way for users who do not have an Enterprise Manager login (such as Line of Business managers) to view charge and usage information. For situations where a bill needs to be produced, chargeback can be integrated with billing applications such as Oracle Billing and Revenue Management (BRM). Further information on Enterprise Manager 12c’s integrated metering and chargeback: White Paper Screenwatch Cloud Management on OTN

    Read the article

  • Identity in .NET 4.5&ndash;Part 3: (Breaking) changes

    - by Your DisplayName here!
    I recently started porting a private build of Thinktecture.IdentityModel to .NET 4.5 and noticed a number of changes. The good news is that I can delete large parts of my library because many features are now in the box. Along the way I found some other nice additions. ClaimsIdentity now has methods to query the claims collection, e.g. HasClaim(), FindFirst(), FindAll(). ClaimsPrincipal has those methods as well. But they work across all contained identities. Nice! ClaimsPrincipal.Current retrieves the ClaimsPrincipal from Thread.CurrentPrincipal. Combined with the above changes, no casting necessary anymore. SecurityTokenHandler now has read and write methods that work directly with strings. This makes it much easier to deal with non-XML tokens like SWT or JWT. A new session security token handler that uses the ASP.NET machine key to protect the cookie. This makes it easier to get started in web farm scenarios. No need for a custom service host factory or the federation behavior anymore. WCF can be switched into “WIF mode” with the useIdentityConfiguration switch (odd name though). Tooling has become better and the new test STS makes it very easy to get started. On the other hand – and that was kind of expected – to bring claims into the core framework, there are also some breaking changes for WIF code. If you want to migrate (and I would recommend that), most changes to your code are mechanical. The following is a brain dump of the changes I encountered. Assembly Microsoft.IdentityModel is gone. The new functionality is now in mscorlib, System.IdentityModel(.Services) and System.ServiceModel. All the namespaces have changed as well. No IClaimsPrincipal and IClaimsIdentity anymore. Configuration section has been split into <system.identityModel /> and <system.identityModel.services />. WCF configuration story has changed as well. Claim.ClaimType is now Claim.Type. ClaimCollection is now IEnumerable<Claim>. IsSessionMode is now IsReferenceMode. Bootstrap token handling is different now. ClaimsPrincipalHttpModule is gone. This is not really needed anymore, apart from maybe claims transformation (see here). Various factory methods on ClaimsPrincipal are gone (e.g. ClaimsPrincipal.CreateFromIdentity()). SecurityTokenHandler.ValidateToken now returns a ReadOnlyCollection<ClaimsIdentity>. Some lower level helper classes are gone or internal now (e.g. KeyGenerator). The WCF WS-Trust bindings are gone. I think this is a pity. They were *really* useful when doing work with WSTrustChannelFactory. Since WIF is part of the Windows operating system and also supported in future versions of .NET, there is no urgent need to migrate to the 4.5 claims model. But obviously, going forward, at some point you want to make the move.

    Read the article

  • Concurrent Affairs

    - by Tony Davis
    I once wrote an editorial, multi-core mania, on the conundrum of ever-increasing numbers of processor cores, but without the concurrent programming techniques to get anywhere near exploiting their performance potential. I came to the.controversial.conclusion that, while the problem loomed for all procedural languages, it was not a big issue for the vast majority of programmers. Two years later, I still think most programmers don't concern themselves overly with this issue, but I do think that's a bigger problem than I originally implied. Firstly, is the performance boost from writing code that can fully exploit all available cores worth the cost of the additional programming complexity? Right now, with quad-core processors that, at best, can make our programs four times faster, the answer is still no for many applications. But what happens in a few years, as the number of cores grows to 100 or even 1000? At this point, it becomes very hard to ignore the potential gains from exploiting concurrency. Possibly, I was optimistic to assume that, by the time we have 100-core processors, and most applications really needed to exploit them, some technology would be around to allow us to do so with relative ease. The ideal solution would be one that allows programmers to forget about the problem, in much the same way that garbage collection removed the need to worry too much about memory allocation. From all I can find on the topic, though, there is only a remote likelihood that we'll ever have a compiler that takes a program written in a single-threaded style and "auto-magically" converts it into an efficient, correct, multi-threaded program. At the same time, it seems clear that what is currently the most common solution, multi-threaded programming with shared memory, is unsustainable. As soon as a piece of state can be changed by a different thread of execution, the potential number of execution paths through your program grows exponentially with the number of threads. If you have two threads, each executing n instructions, then there are 2^n possible "interleavings" of those instructions. Of course, many of those interleavings will have identical behavior, but several won't. Not only does this make understanding how a program works an order of magnitude harder, but it will also result in irreproducible, non-deterministic, bugs. And of course, the problem will be many times worse when you have a hundred or a thousand threads. So what is the answer? All of the possible alternatives require a change in the way we write programs and, currently, seem to be plagued by performance issues. Software transactional memory (STM) applies the ideas of database transactions, and optimistic concurrency control, to memory. However, working out how to break down your program into sufficiently small transactions, so as to avoid contention issues, isn't easy. Another approach is concurrency with actors, where instead of having threads share memory, each thread runs in complete isolation, and communicates with others by passing messages. It simplifies concurrent programs but still has performance issues, if the threads need to operate on the same large piece of data. There are doubtless other possible solutions that I haven't mentioned, and I would love to know to what extent you, as a developer, are considering the problem of multi-core concurrency, what solution you currently favor, and why. Cheers, Tony.

    Read the article

  • How can I change the color of the text in my iFrame? [closed]

    - by VinylScratch
    I have code here: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html> <head> <title>Frag United Banlist</title> </head> <body> <h1>Tekkit Banlist</h1> <?php // change these things $server = "server-host"; $dbuser = "correct-user"; $dbpass = "correct-password"; $dbname = "correct-database"; mysql_connect($server, $dbuser, $dbpass); mysql_select_db($dbname); $result = mysql_query("SELECT * FROM banlist ORDER BY id DESC"); //This will display the most recent by id edit this query how you see fit. Limit, Order, ect. echo "<table width=100% border=1 cellpadding=3 cellspacing=0>"; echo "<tr style=\"font-weight:bold\"> <td>ID</td> <td>User</td> <td>Reason</td> <td>Admin/Mod</td> <td>Time</td> <td>Ban Length</td> </tr>"; while($row = mysql_fetch_assoc($result)){ if($col == "#eeeeee"){ $col = "#ffffff"; }else{ $col = "#eeeeee"; } echo "<tr bgcolor=$col>"; echo "<td>".$row['id']."</td>"; echo "<td>".$row['user']."</td>"; echo "<td>".$row['reason']."</td>"; echo "<td>".$row['admin']."</td>"; //Convert Epoch Time to Standard format $datetime = date("F j, Y, g:i a", $row['time']); echo "<td>$datetime</td>"; $dateconvert = date("F j, Y, g:i a", $row['length']); if($row['length'] == "0"){ echo "<td>None</td>"; }else{ echo "<td>$dateconvert</td>"; } echo "<td>".$row['id']."</td>"; echo "</tr>"; } echo"</table>" ?> </div> </body></html> And I am trying to make it so that when I put it in this iframe: <iframe src="http://bans.fragunited.net/" width="100%" length="100%"><p>Your browser does not support iframes.</p></iframe> But if you go to this page, fragunited.net/bans, (not bans.fragunited.net) the text is black and I want it to be white so you can actually see it. Sorry for the large amount of code, however I don't know where you have to put the code to change the color.

    Read the article

  • Frequently getting booted from Securemote VPN-1 Connection

    - by Nick L.
    I connect to my office's network remotely through the Checkpoint SecuRemote E75 (R75) VPN application, but recently it's been causing me a lot of issues when connecting from home. I connect through a WRT54GL router running DD-WRT v24 firmware, so I have no clue if that affects anything. I took a dump of the logs for Checkpoint and here are the messages that populate when I get booted but I have no clue how to decipher them and my IT department is completely clueless in terms of resolving the situation. I'm thinking the router is blocking the keep alive connection or something along those lines, but I have no idea how to fix the problem. [ 2388 2932][30 Aug 22:47:49][TR_OFFICE_MODE] TR_OFFICE_MODE::TrOfficeMode::OmSendIpFrameCB: Not sending packet because it's not to the enc domain [ 2388 2932][30 Aug 22:47:50][TR_EVENTS] TR_EVENTS::Raise: Running registered cb... [ 2388 2932][30 Aug 22:47:50][TrComInf] TrComInf::TrComInfSendAsynchronic: __start__ 22:47:50.606 [ 2388 2932][30 Aug 22:47:50][TrComInf] TrComInf::TrComInf::TrComInfSendAsynchronic: Acquiring mutex [ 2388 2932][30 Aug 22:47:50][messaging] messaging::send_all: Sending Message {{ 2 }} , len 185 [ 2388 2932][30 Aug 22:47:50][tcpserver] TcpMultiPipe::pipe_if_send: Message (193 bytes) written successfully to socket 0x224 [ 2388 2932][30 Aug 22:47:50][TrComInf] TrComInf::TrComInf::TrComInfSendAsynchronic: Released mutex [ 2388 2932][30 Aug 22:47:50][TrComInf] TrComInf::TrComInfSendAsynchronic: __end__ 22:47:50.606. Total time - 0 milliseconds [ 2388 2932][30 Aug 22:47:50][TR_SRV2CL] TR_SRV2CL::SendNotification: Successfully sent notification of type TR_NOTIFICATION_TRAFFIC_IDLE [ 2388 2932][30 Aug 22:47:50][vna] vna_trap: received VNA_TRAP_FORWARD_PACKET [ 2388 2932][30 Aug 22:47:50][vna] vna_traffic_fwd_do : forwarding packet with 98 bytes [ 2388 2932][30 Aug 22:47:50][TR_OFFICE_MODE] TrOfficeMode::OmSendIpFrameCB: Packet to destination 192.168.162.15 of protocol 17 [ 2388 2932][30 Aug 22:47:50][TR_OFFICE_MODE] TR_OFFICE_MODE::TrOfficeMode::OmSendIpFrameCB: Not sending packet because it's not to the enc domain [ 2388 2932][30 Aug 22:47:51][vna] vna_trap: received VNA_TRAP_FORWARD_PACKET [ 2388 2932][30 Aug 22:47:51][vna] vna_traffic_fwd_do : forwarding packet with 98 bytes [ 2388 2932][30 Aug 22:47:51][TR_OFFICE_MODE] TrOfficeMode::OmSendIpFrameCB: Packet to destination 192.168.162.15 of protocol 17 [ 2388 2932][30 Aug 22:47:51][TR_OFFICE_MODE] TR_OFFICE_MODE::TrOfficeMode::OmSendIpFrameCB: Not sending packet because it's not to the enc domain [ 2388 2392][30 Aug 22:47:52][TracService] service_ctrl_ex: Called with ctrl_code 14 [ 2388 2392][30 Aug 22:47:52][TracService] service_ctrl_ex: System got SERVICE_CONTROL_SESSIONCHANGE message event type 4 session 2 [ 2388 2392][30 Aug 22:47:52][TracService] service_ctrl_ex: Console/remote disconnect has occured in session 2 [ 2388 2932][30 Aug 22:47:52][vna] vna_trap: received VNA_TRAP_FORWARD_PACKET [ 2388 2932][30 Aug 22:47:52][vna] vna_traffic_fwd_do : forwarding packet with 98 bytes [ 2388 2932][30 Aug 22:47:52][TR_OFFICE_MODE] TrOfficeMode::OmSendIpFrameCB: Packet to destination 192.168.162.15 of protocol 17 [ 2388 2932][30 Aug 22:47:52][TR_OFFICE_MODE] TR_OFFICE_MODE::TrOfficeMode::OmSendIpFrameCB: Not sending packet because it's not to the enc domain [ 2388 2932][30 Aug 22:47:52][TR_CONN_MANAGER] TR_CONN_MANAGER::ConnEnum: Returning connection at position 1 [ 2388 2932][30 Aug 22:47:52][TR_EVENTS] TR_EVENTS::Raise: Running registered cb... [ 2388 2932][30 Aug 22:47:52][TR_CONN_MANAGER] TR_CONN_MANAGER::ConnEventMainHandler: no gw handle [ 2388 2932][30 Aug 22:47:52][TR_CONN_MANAGER] TR_CONN_MANAGER::ConnEventMainHandler: Current connection state is TR_CONN_STATE_CONNECTED. Receiving event of type CONN_EVENT_SYSTEM_SESSION_LOGOFF. Connection handle = 1. System state: TR_SYSTEM_STATE_RUNNING [ 2388 2932][30 Aug 22:47:52][CONFIG_MANAGER] suspend_tunnel_while_locked return value false, because it is Default variable. Scope: site 12.43.159.10, gw NULL ,user USER [ 2388 2932][30 Aug 22:47:52][TR_CONN_MANAGER] TR_CONN_MANAGER::ConnEventConnectedHandler: no gw handle [ 2388 2932][30 Aug 22:47:52][TR_CONN_MANAGER] TR_CONN_MANAGER::ConnEventConnectedHandler: receive session logoff event while connected. cancelling connection Thanks all. :)

    Read the article

  • Apache2 configuration error: "<VirtualHost> was not closed" error

    - by Chris
    So I've already checked through my config file and I really can't see an instance where any tag hasn't been properly closed...but I keep getting this configuration error...Would you mind taking a look through the error and the config file below? Any assistance would be greatly appreciated. FYI, I've already googled the life out of the error and looked through the log extensively, I really can't find anything. Error: apache2: Syntax error on line 236 of /etc/apache2/apache2.conf: syntax error on line 1 of /etc/apache2/sites-enabled/000-default: /etc/apache2/sites-enabled/000-default:1: was not closed. Line 236 of apache2.conf: # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ Contents of 000-default: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> <VirtualHost *:443> SetEnvIf Request_URI "^/u" dontlog ErrorLog /var/log/apache2/error.log Loglevel warn SSLEngine On SSLCertificateFile /etc/apache2/ssl/apache.pem ProxyRequests Off <Proxy *> AuthUserFile /srv/ajaxterm/.htpasswd AuthName EnterPassword AuthType Basic require valid-user Order Deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8022/ ProxyPassReverse / http://localhost:8022/ </VirtualHost> UPDATE I had a load of other issues with my install so I wound up just wiping it and reinstalling. If I run into the same problem, I'll repost. Everyone, thanks for your help/suggestions.

    Read the article

  • x.gif in Apache logs

    - by T. Stone
    I manage a Django site where we host the media on a subdomain. There shouldn't be any requests for media to the main domain. However I keep seeing these requests for "x.gif" showing up in the access logs on the domain that's handled by WSGI (not the media domain). Can anyone explain what this is? X.X.X.X - - [08/Mar/2010:10:04:00 -1000] "GET / HTTP/1.1" 200 3724 X.X.X.X - - [08/Mar/2010:10:04:10 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:10 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:10 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:10 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:51 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:52 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:52 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:52 -1000] "GET /x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:56 -1000] "GET /contact/ HTTP/1.1" 200 7196 X.X.X.X - - [08/Mar/2010:10:04:58 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:04:58 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:00 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:00 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:00 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:00 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:01 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:01 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:01 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:01 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:02 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:02 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:02 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:02 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:03 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:03 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:03 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:04 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:04 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:04 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:04 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:05 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:05 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:05 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:05 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:06 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:06 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:06 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653 X.X.X.X - - [08/Mar/2010:10:05:06 -1000] "GET /contact/x.gif HTTP/1.1" 404 2653

    Read the article

  • CentOS 5.5 : Postfix, Dovecot & MySQL

    - by GruffTech
    I'm hoping someone has seen this issue before because I'm at quite a loss. We're building a new outbound smtp server for our clients that features anti-spam scanning and virus scanning for outbound emails, something we had not previously done. So with CentOS 5.5 x64, Installed and patched completely. Postfix & Dovecot both installed via base repo. [grufftech@outgoing postfix]# rpm -qa | grep postfix postfix-2.3.3-2.1.el5_2 [grufftech@outgoing postfix]# rpm -qa | grep dovecot dovecot-1.0.7-7.el5 [grufftech@outgoing ~]# dovecot --build-options Build options: ioloop=poll notify=inotify ipv6 openssl SQL drivers: mysql postgresql Passdb: checkpassword ldap pam passwd passwd-file shadow sql Userdb: checkpassword ldap passwd prefetch passwd-file sql static /etc/dovecot.conf auth default { mechanisms = plain login digest-md5 cram-md5 passdb sql { args = /etc/dovecot-mysql.conf } userdb sql { args = /etc/dovecot-mysql.conf } userdb prefetch { } user = nobody socket listen { master { path = /var/run/dovecot/auth-master mode = 0660 user = postfix group = postfix } client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } } } All the server is doing is auth for postfix, so no reason to have imap / pop / dict. /etc/dovecot-mysql.conf driver = mysql connect = host=10.0.32.159 dbname=mail user=****** password=******** default_pass_scheme = plain user_query = select 1 password_query = select password from users where username = '%n' and domain = '%d' So drop in my configuration, (which is working on another server identical to this one.) [grufftech@outgoing ~]# /etc/init.d/dovecot start Starting Dovecot Imap: [ OK ] Sweet. Booted up nicely, thats good.... (incoming problem in 3....2....1....) May 21 08:09:01 outgoing dovecot: Dovecot v1.0.7 starting up May 21 08:09:02 outgoing dovecot: auth-worker(default): mysql: Connect failed to 10.0.32.159 (mail): Can't connect to MySQL server on '10.0.32.159' (13) - waiting for 1 seconds before retry well what the crap. went and checked permissions on my MySQL database, and its fine. [grufftech@outgoing ~]# mysql vpopmail -h 10.0.32.159 -u ****** -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 127828558 Server version: 4.1.22 Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql>\q So! My server can talk to my database server. but dovecot, for whatever reason, isn't able to. I've fiddled with it for the last six hours, grabbed slightly-older copies of the RPM (ones that matched our production server exactly) to test those, copied configs, searched google, searched server fault, chatted in IRC, banged my head against the table, I've done it all. Surely I'm doing something wrong or forgetting something, can anyone tell me what the elephant in the room is? This stuff is supposed to work.

    Read the article

  • Wubi and Vista 64 bits can't work

    - by Daok
    First of all, I have posted this issue at Ubuntu Forum without success yet. Hello, I have downloaded "kubuntu-9.10-desktop-amd64.iso" and I have mounted it on my Windows Vista 64 bits Ultimate. I have downloaded wubi 9.10. The problem is when installing, it crash after few time. Here is the log file: 11-26 21:07 INFO root: === wubi 9.10ubuntu1 rev160 === 11-26 21:07 DEBUG root: Logfile is c:\users\patrick\appdata\local\temp\wubi-9.10ubuntu1-rev160.log 11-26 21:07 DEBUG root: sys.argv = ['main.pyo', '--exefile="Z:\\wubi.exe"'] 11-26 21:07 DEBUG CommonBackend: data_dir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\data 11-26 21:07 DEBUG WindowsBackend: 7z=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\bin\7z.exe 11-26 21:07 DEBUG CommonBackend: Fetching basic info... 11-26 21:07 DEBUG CommonBackend: original_exe=Z:\wubi.exe 11-26 21:07 DEBUG CommonBackend: platform=win32 11-26 21:07 DEBUG CommonBackend: osname=nt 11-26 21:07 DEBUG CommonBackend: language=fr_CA 11-26 21:07 DEBUG CommonBackend: encoding=cp1252 11-26 21:07 DEBUG WindowsBackend: arch=amd64 11-26 21:07 DEBUG CommonBackend: Parsing isolist=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\data\isolist.ini 11-26 21:07 DEBUG CommonBackend: Adding distro Xubuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro Xubuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Kubuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Mythbuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro Ubuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Ubuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro Mythbuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Kubuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro KubuntuNetbook-i386 11-26 21:07 DEBUG CommonBackend: Adding distro UbuntuNetbookRemix-i386 11-26 21:07 DEBUG WindowsBackend: Fetching host info... 11-26 21:07 DEBUG WindowsBackend: registry_key=Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi 11-26 21:07 DEBUG WindowsBackend: windows version=vista 11-26 21:07 DEBUG WindowsBackend: windows_version2=Windows (TM) Vista Ultimate 11-26 21:07 DEBUG WindowsBackend: windows_sp=None 11-26 21:07 DEBUG WindowsBackend: windows_build=6002 11-26 21:07 DEBUG WindowsBackend: gmt=-5 11-26 21:07 DEBUG WindowsBackend: country=CA 11-26 21:07 DEBUG WindowsBackend: timezone=America/Montreal 11-26 21:07 DEBUG WindowsBackend: windows_username=Patrick 11-26 21:07 DEBUG WindowsBackend: user_full_name=Patrick 11-26 21:07 DEBUG WindowsBackend: user_directory=C:\Users\Patrick 11-26 21:07 DEBUG WindowsBackend: windows_language_code=1036 11-26 21:07 DEBUG WindowsBackend: windows_language=French 11-26 21:07 DEBUG WindowsBackend: processor_name=Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz 11-26 21:07 DEBUG WindowsBackend: bootloader=vista 11-26 21:07 DEBUG WindowsBackend: system_drive=Drive(C: hd 239816.335938 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(C: hd 239816.335938 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(D: cd 0.0 mb free ) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(E: hd 483619.367188 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(G: hd 84606.9375 mb free fat32) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(Z: cd 0.0 mb free cdfs) 11-26 21:07 DEBUG WindowsBackend: uninstaller_path=C:\ubuntu\uninstall-wubi.exe 11-26 21:07 DEBUG WindowsBackend: previous_target_dir=C:\ubuntu 11-26 21:07 DEBUG WindowsBackend: previous_distro_name=Kubuntu 11-26 21:07 DEBUG WindowsBackend: keyboard_id=269029385 11-26 21:07 DEBUG WindowsBackend: keyboard_layout=ca 11-26 21:07 DEBUG WindowsBackend: keyboard_variant= 11-26 21:07 DEBUG CommonBackend: python locale=('fr_CA', 'cp1252') 11-26 21:07 DEBUG CommonBackend: locale=fr_CA.UTF-8 11-26 21:07 DEBUG WindowsBackend: total_memory_mb=4095.99999905 11-26 21:07 DEBUG CommonBackend: Searching ISOs on USB devices 11-26 21:07 DEBUG CommonBackend: Searching for local CDs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: parsing info from str=Kubuntu 9.10 "Karmic Koala" - Release amd64 (20091027) 11-26 21:07 DEBUG Distro: parsed info={'name': 'Kubuntu', 'subversion': 'Release', 'version': '9.10', 'build': '20091027', 'codename': 'Karmic Koala', 'arch': 'amd64'} 11-26 21:07 DEBUG Distro: wrong name: Kubuntu != Ubuntu 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: wrong name: Kubuntu != Ubuntu 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: wrong name: Kubuntu != Ubuntu Netbook Remix 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Kubuntu CD 11-26 21:07 INFO Distro: Found a valid CD for Kubuntu: Z:\ 11-26 21:07 INFO root: Running the CD menu... 11-26 21:07 DEBUG WindowsFrontend: __init__... 11-26 21:07 DEBUG WindowsFrontend: on_init... 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['fr_CA', 'fr'] 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['fr_CA', 'fr'] 11-26 21:07 INFO root: CD menu finished 11-26 21:07 INFO root: Already installed, running the uninstaller... 11-26 21:07 INFO root: Running the uninstaller... 11-26 21:07 INFO CommonBackend: This is the uninstaller running 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['fr_CA', 'fr'] 11-26 21:07 INFO root: Received settings 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['fr_CA', 'fr'] 11-26 21:07 DEBUG TaskList: # Running tasklist... 11-26 21:07 DEBUG TaskList: ## Running Sauvegarder l'ISO... 11-26 21:07 DEBUG TaskList: ## Finished Sauvegarder l'ISO 11-26 21:07 DEBUG TaskList: ## Running Supprimer l'entrée pour le programme d'amorçage... 11-26 21:07 DEBUG WindowsBackend: Could not find bcd id 11-26 21:07 DEBUG WindowsBackend: undo_bootini C: 11-26 21:07 DEBUG WindowsBackend: undo_configsys Drive(C: hd 239816.335938 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: undo_bootini E: 11-26 21:07 DEBUG WindowsBackend: undo_configsys Drive(E: hd 483619.367188 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: undo_bootini G: 11-26 21:07 DEBUG WindowsBackend: undo_configsys Drive(G: hd 84606.9375 mb free fat32) 11-26 21:07 DEBUG TaskList: ## Finished Supprimer l'entrée pour le programme d'amorçage 11-26 21:07 DEBUG TaskList: ## Running Supprimer le répertoire cible... 11-26 21:07 DEBUG CommonBackend: Deleting C:\ubuntu 11-26 21:07 DEBUG TaskList: ## Finished Supprimer le répertoire cible 11-26 21:07 DEBUG TaskList: ## Running Supprimer la clé du registre... 11-26 21:07 DEBUG TaskList: ## Finished Supprimer la clé du registre 11-26 21:07 DEBUG TaskList: # Finished tasklist 11-26 21:07 INFO root: Almost finished uninstalling 11-26 21:07 INFO root: Finished uninstallation 11-26 21:07 DEBUG CommonBackend: Fetching basic info... 11-26 21:07 DEBUG CommonBackend: original_exe=Z:\wubi.exe 11-26 21:07 DEBUG CommonBackend: platform=win32 11-26 21:07 DEBUG CommonBackend: osname=nt 11-26 21:07 DEBUG WindowsBackend: arch=amd64 11-26 21:07 DEBUG CommonBackend: Parsing isolist=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\data\isolist.ini 11-26 21:07 DEBUG CommonBackend: Adding distro Xubuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro Xubuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Kubuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Mythbuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro Ubuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Ubuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro Mythbuntu-amd64 11-26 21:07 DEBUG CommonBackend: Adding distro Kubuntu-i386 11-26 21:07 DEBUG CommonBackend: Adding distro KubuntuNetbook-i386 11-26 21:07 DEBUG CommonBackend: Adding distro UbuntuNetbookRemix-i386 11-26 21:07 DEBUG WindowsBackend: Fetching host info... 11-26 21:07 DEBUG WindowsBackend: registry_key=Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi 11-26 21:07 DEBUG WindowsBackend: windows version=vista 11-26 21:07 DEBUG WindowsBackend: windows_version2=Windows (TM) Vista Ultimate 11-26 21:07 DEBUG WindowsBackend: windows_sp=None 11-26 21:07 DEBUG WindowsBackend: windows_build=6002 11-26 21:07 DEBUG WindowsBackend: gmt=-5 11-26 21:07 DEBUG WindowsBackend: country=CA 11-26 21:07 DEBUG WindowsBackend: timezone=America/Montreal 11-26 21:07 DEBUG WindowsBackend: windows_username=Patrick 11-26 21:07 DEBUG WindowsBackend: user_full_name=Patrick 11-26 21:07 DEBUG WindowsBackend: user_directory=C:\Users\Patrick 11-26 21:07 DEBUG WindowsBackend: windows_language_code=1036 11-26 21:07 DEBUG WindowsBackend: windows_language=French 11-26 21:07 DEBUG WindowsBackend: processor_name=Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz 11-26 21:07 DEBUG WindowsBackend: bootloader=vista 11-26 21:07 DEBUG WindowsBackend: system_drive=Drive(C: hd 240512.851563 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(C: hd 240512.851563 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(D: cd 0.0 mb free ) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(E: hd 483523.867188 mb free ntfs) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(G: hd 84445.65625 mb free fat32) 11-26 21:07 DEBUG WindowsBackend: drive=Drive(Z: cd 0.0 mb free cdfs) 11-26 21:07 DEBUG WindowsBackend: uninstaller_path=None 11-26 21:07 DEBUG WindowsBackend: previous_target_dir=None 11-26 21:07 DEBUG WindowsBackend: previous_distro_name=None 11-26 21:07 DEBUG WindowsBackend: keyboard_id=269029385 11-26 21:07 DEBUG WindowsBackend: keyboard_layout=ca 11-26 21:07 DEBUG WindowsBackend: keyboard_variant= 11-26 21:07 DEBUG WindowsBackend: total_memory_mb=4095.99999905 11-26 21:07 DEBUG CommonBackend: Searching ISOs on USB devices 11-26 21:07 DEBUG CommonBackend: Searching for local CDs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Kubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Kubuntu Netbook CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Xubuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether G:\ is a valid Mythbuntu CD 11-26 21:07 DEBUG Distro: does not contain G:\casper\filesystem.squashfs 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: wrong name: Kubuntu != Ubuntu 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Ubuntu CD 11-26 21:07 DEBUG Distro: wrong name: Kubuntu != Ubuntu 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Ubuntu Netbook Remix CD 11-26 21:07 DEBUG Distro: wrong name: Kubuntu != Ubuntu Netbook Remix 11-26 21:07 DEBUG Distro: checking whether Z:\ is a valid Kubuntu CD 11-26 21:07 INFO Distro: Found a valid CD for Kubuntu: Z:\ 11-26 21:07 INFO root: Running the installer... 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['fr_CA', 'fr'] 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['fr_CA', 'fr'] 11-26 21:07 DEBUG WinuiInstallationPage: target_drive=C:, installation_size=17000MB, distro_name=Kubuntu, language=en_US, locale=en_US.UTF-8, username=patrick 11-26 21:07 INFO root: Received settings 11-26 21:07 INFO WinuiPage: appname=wubi, localedir=C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\translations, languages=['en_US', 'en'] 11-26 21:07 DEBUG TaskList: # Running tasklist... 11-26 21:07 DEBUG TaskList: ## Running select_target_dir... 11-26 21:07 INFO WindowsBackend: Installing into C:\ubuntu 11-26 21:07 DEBUG TaskList: ## Finished select_target_dir 11-26 21:07 DEBUG TaskList: ## Running create_dir_structure... 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu\disks 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu\install 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu\install\boot 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu\disks\boot 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu\disks\boot\grub 11-26 21:07 DEBUG CommonBackend: Creating dir C:\ubuntu\install\boot\grub 11-26 21:07 DEBUG TaskList: ## Finished create_dir_structure 11-26 21:07 DEBUG TaskList: ## Running uncompress_target_dir... 11-26 21:07 DEBUG TaskList: ## Finished uncompress_target_dir 11-26 21:07 DEBUG TaskList: ## Running create_uninstaller... 11-26 21:07 DEBUG WindowsBackend: Copying uninstaller Z:\wubi.exe -> C:\ubuntu\uninstall-wubi.exe 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi UninstallString C:\ubuntu\uninstall-wubi.exe 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi InstallationDir C:\ubuntu 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayName Kubuntu 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayIcon C:\ubuntu\Kubuntu.ico 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayVersion 9.10ubuntu1-rev160 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi Publisher Kubuntu 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi URLInfoAbout http://www.kubuntu.org 11-26 21:07 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi HelpLink http://www.ubuntu.com/support 11-26 21:07 DEBUG TaskList: ## Finished create_uninstaller 11-26 21:07 DEBUG TaskList: ## Running copy_installation_files... 11-26 21:07 DEBUG WindowsBackend: Copying C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\data\custom-installation -> C:\ubuntu\install\custom-installation 11-26 21:07 DEBUG WindowsBackend: Copying C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\winboot -> C:\ubuntu\winboot 11-26 21:07 DEBUG WindowsBackend: Copying C:\Users\Patrick\AppData\Local\Temp\pyl5A09.tmp\data\images\Kubuntu.ico -> C:\ubuntu\Kubuntu.ico 11-26 21:07 DEBUG TaskList: ## Finished copy_installation_files 11-26 21:07 DEBUG TaskList: ## Running get_iso... 11-26 21:07 DEBUG TaskList: New task copy_file 11-26 21:07 DEBUG TaskList: ### Running copy_file... 11-26 21:09 DEBUG TaskList: ### Finished copy_file 11-26 21:09 ERROR TaskList: [Errno 22] Invalid argument Traceback (most recent call last): File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\common\utils.py", line 209, in copy_file IOError: [Errno 22] Invalid argument 11-26 21:09 DEBUG TaskList: # Cancelling tasklist 11-26 21:09 DEBUG TaskList: New task check_iso 11-26 21:09 ERROR root: [Errno 22]

    Read the article

  • Handling bounced email when using a postfix smarthost

    - by Mark Rose
    I'm running a high availability cluster, and so far, most things work great. I have two external machines that act as outgoing mail hosts (smarthosts). The internal hosts are configured to relay all email through these two external facing hosts. My smarthosts' main.cf looks like this: myhostname = lb1.example.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mydestination = lb1.example.com, localhost relayhost = mynetworks = 127.0.0.0/8 10.1.248.0/24 My internal hosts' main.cf looks like this: mynetworks = 127.0.0.0/8 myhostname = web1.example.com mydestination = $myhostname, localhost.$mydomain, localhost relayhost = [10.1.248.3] smtp_fallback_relay = [10.1.248.2] lb1's internal IP is 10.1.248.2, and lb2's internal IP is 10.1.248.3. On the external hosts, email for root and www-data is forwarded to [email protected] with /etc/aliases. One advantage to using the smarthost setup is that spam filters and the like can connect back to the sending sending server. All email is sent fine, and headers look like this: Received: from lb2.example.com ([198.51.100.3]) by mx.google.com with ESMTP id y17si1571259icb.76.2011.01.13.18.20.32; Thu, 13 Jan 2011 18:20:32 -0800 (PST) Received-SPF: neutral (google.com: 198.51.100.3 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=198.51.100.3; Received: from db1.example.com (unknown [10.1.248.20]) by lb2.example.com (Postfix) with ESMTP id D364823C0BE for <[email protected]>; Thu, 13 Jan 2011 21:20:31 -0500 (EST) Received: by db1.example.com (Postfix) id C9FA7760D6A; Thu, 13 Jan 2011 21:20:31 -0500 (EST) Delivered-To: www-data@localhost Received: by db1.example.com (Postfix, from userid 0) id C1632760D6C; Thu, 13 Jan 2011 21:20:31 -0500 (EST) The problem is bounced/reject email. The external machine tries to forward the email back to the internal machine, e.g. www-data on web1 sending an email that bounces (such as a user signing up with a bad email address). An additional complication is using Google mail for the main example.com domain. In lieu of specifying every internal host in the external hosts' mydestination, is there a better way of setting things up, keeping in mind I can't adjust touch the mx for example.com?

    Read the article

  • SSL connection errors from Apache

    - by Yang
    I'm running a (self-signed) SSL cert site on Apache/2.2.14 on Ubuntu 10.04, but various browsers are giving errors on half the connection attempts. Just now saw this transient error from Chrome: "Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error." Hit refresh and the problem goes away for a while. wget too: $ wget --no-check-certificate https://dev.foo.com/deps/ --2010-09-08 19:30:26-- https://dev.foo.com/deps/ Resolving dev.foo.com... 184.72.53.220 Connecting to dev.foo.com|184.72.53.220|:443... connected. OpenSSL: error:0407006A:rsa routines:RSA_padding_check_PKCS1_type_1:block type is not 01 OpenSSL: error:04067072:rsa routines:RSA_EAY_PUBLIC_DECRYPT:padding check failed OpenSSL: error:1408D07B:SSL routines:SSL3_GET_KEY_EXCHANGE:bad signature Unable to establish SSL connection. Run it right away again and it works: $ wget --no-check-certificate https://dev.foo.com/deps/ --2010-09-08 19:30:29-- https://dev.foo.com/deps/ Resolving dev.foo.com... 184.72.53.220 Connecting to dev.foo.com|184.72.53.220|:443... connected. WARNING: cannot verify dev.foo.com's certificate, issued by `/CN=dev.foo.com': Self-signed certificate encountered. HTTP request sent, awaiting response... 200 OK Length: 3157 (3.1K) [text/html] Saving to: `index.html' 100%[======================================>] 3,157 --.-K/s in 0s 2010-09-08 19:30:29 (48.6 MB/s) - `index.html' saved [3157/3157] In my sites-enabled/default-ssl: SSLCertificateFile /etc/ssl/certs/ssl-cert-snakeoil.pem SSLCertificateKeyFile /etc/ssl/private/ssl-cert-snakeoil.key The cert: -----BEGIN CERTIFICATE----- MIIBszCCARwCCQCa0TzNwqLgsTANBgkqhkiG9w0BAQUFADAeMRwwGgYDVQQDExNk ZXYucGFydHlvbmRhdGEuY29tMB4XDTEwMDgyNzA2MzA1N1oXDTIwMDgyNDA2MzA1 N1owHjEcMBoGA1UEAxMTZGV2LnBhcnR5b25kYXRhLmNvbTCBnzANBgkqhkiG9w0B AQEFAAOBjQAwgYkCgYEAzXDEULpCUqIc9hV/ESFapkckR2uoYINA81DvG2aQZ9Ot Q30OwX2ae2CC4bSzJEIVlahU8vjVrWpmpa28NEhQbqh4ywwbl1XDrEVYI6Gkfimf snJhOKyaVrEhlwutYtBjmsz3ZIqwymMPm/6smVcSS5dJIynlSmtltxX6ivPcO8UC AwEAATANBgkqhkiG9w0BAQUFAAOBgQBGxHVkpSSOnZjzuySRepjhAlV/yhe9Fx23 fh12WrjQMEi98B7JEuNSLXDWckUN7O6XRc3RzKmazcGHJqzhn0Ov6gAmAE2XjZ/x VW21xmaLwk+KgYKFJbJJaP3jMSpU7I3aa11wqAkR2Zd4Nkm9N0YXYIzcBdfztTVI Et8mEHBFdg== -----END CERTIFICATE----- The cert is in turn generated via: $ make-ssl-cert generate-default-snakeoil --force-overwrite Apache version. $ apache2 -V Server version: Apache/2.2.14 (Ubuntu) Server built: Apr 13 2010 20:22:19 Server's Module Magic Number: 20051115:23 Server loaded: APR 1.3.8, APR-Util 1.3.9 Compiled using: APR 1.3.8, APR-Util 1.3.9 Architecture: 64-bit Server MPM: Worker threaded: yes (fixed thread count) forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/worker" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="" -D SUEXEC_BIN="/usr/lib/apache2/suexec" -D DEFAULT_PIDLOG="/var/run/apache2.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="/etc/apache2/mime.types" -D SERVER_CONFIG_FILE="/etc/apache2/apache2.conf" I don't administer the network, hardware, etc. - this is all running on Amazon EC2. I'm not running a load-balancer or anything else in front of the server. I'm making direct TCP connections to that host (AFAIK). Any ideas? Thanks in advance for any help.

    Read the article

  • SQL Server Agent was not running on Server Dynamics CRM 2013

    - by No1_Melman
    I'm trying to install Dynamics CRM 2013 on a server. This server is on a VM. There are several other VMs, an ADDS & DNS, a MSSQL and a WebServer VM. Each server is a Windows Server 2012 R2. The SQL Server is 2012 Enterprise. Each VM is part of the main Domain, set by the ADDS & DNS. NSLookup confirms I can see the computer at the right IP address. Each separate VM has its own static IP, the DNS is set to the ADDS & DNS. I use the domain administrator to log into all the servers, and make the that domain administrator a local administrator. I've set up all the domain users for the CRM and gave them appropriate permissions, I have also added the accounts to the appropriate places, such that the CRM Deployment user is in the SQL security. The SQL Agent is running. SQL server configuration manager has SQL server network configuration TCP/IP enabled to allow remote connections. The SQL server has the domain user as a administrator, which is the same user being used to install the CRM. In the CRM setup i point to the [Servername]\[Instance] and I have also tried just the [Servername]. to make this easier I called the server MSSQL and left the instance name to the default. I even install the MSSQL instance as the domain administrator. CRM can find the ReportServer url. I have enable all the ports required, including: 135, 1433, 1434, 2382, 2383, 4022. 1434 UDP. I feel like I have absolutely done everything, I have google many times and tried all the different methods, and for the life of me I cant seem to get the CRM setup to find the SQL server agent. It passes everything else perfectly fine. I can even ping the MSSQL server. What is the problem, why does the CRM still keep giving the error: SQLSERVERAGENT (SQLSERVERAGENT) service is not running on the server MSSQL On the MSSQL server, the name of the sql server agent service is: SQL Server Agent (MSSQLSERVER)

    Read the article

  • How do I get a .Net 4.0 app to coexist as an application under a SharePoint 2007 website in IIS v7?

    - by Craig Nakamoto
    I have created a small .Net 4.0 website and installed it on my SharePoint server as a separate web site in IIS v7 (using port 8008 for now). I had to install the .Net 4 framework, set up the database, etc. and this all went smoothly and my app works as a standalone website. Now I am trying to get pages from my website to show up in SharePoint 2007. For various reasons (the SharePoint site is using SSL, security, etc.) I now need to move my .Net app to run under the SharePoint 2007 site in IIS. I have added it as an 'Application' and set it up with the same .Net v4 application pool and settings that were working when it was set up as a standalone site. Now when I try to access the application I get the error at the end of this description. Any help would be greatly appreciated. I already tried following the instructions on this post: http://blogs.msdn.com/sgoodyear/archive/2007/05/07/custom-web-applications-coexisting-with-sharepoint-2007.aspx but that did not help. Thanks! Craig p.s. Here are the error details: Log Name: Application Source: ASP.NET 4.0.30319.0 Date: 11/05/2010 11:49:31 AM Event ID: 1310 Task Category: Web Event Level: Warning Keywords: Classic User: N/A Computer: GGI-SP1.ggi.ca Description: Event code: 3008 Event message: A configuration error has occurred. Event time: 11/05/2010 11:49:31 AM Event time (UTC): 11/05/2010 3:49:31 PM Event ID: 559d7ac619344f3499a4a31c6c9e58cd Event sequence: 1 Event occurrence: 1 Event detail code: 0 Application information: Application domain: /LM/W3SVC/1653978112/ROOT/bidmonitor-1-129180665715766107 Trust level: Application Virtual Path: /bidmonitor Application Path: C:\inetpub\wwwroot\bidmonitor\ Machine name: GGI-SP1 Process information: Process ID: 5272 Process name: w3wp.exe Account name: NT AUTHORITY\NETWORK SERVICE Exception information: Exception type: ConfigurationErrorsException Exception message: Could not find permission set named 'ASP.Net'. at System.Web.Hosting.ApplicationManager.CreateAppDomainWithHostingEnvironment(String appId, IApplicationHost appHost, HostingEnvironmentParameters hostingParameters) at System.Web.HttpRuntime.HostingInit(HostingEnvironmentFlags hostingFlags, PolicyLevel policyLevel, Exception appDomainCreationException) Request information: Request URL: gginet.ggi.ca/bidmonitor Request path: /bidmonitor User host address: 10.10.1.33 User: Is authenticated: False Authentication Type: Thread account name: NT AUTHORITY\NETWORK SERVICE Thread information: Thread ID: 3 Thread account name: NT AUTHORITY\NETWORK SERVICE Is impersonating: False Stack trace: at System.Web.HttpRuntime.HostingInit(HostingEnvironmentFlags hostingFlags, PolicyLevel policyLevel, Exception appDomainCreationException)

    Read the article

  • ESXI Crash need help to understand log and support about nexentastor on virtual machine

    - by Bgnt44
    If i understand right, the following core dump means that the cpu4 has crashed the Host if i read the next line it seem that at the time the CPU 4 was assigned to the NexentaStore Vm ... SO if im right i can say that NexentaStor Vm crash my esxi Am i right ? Does that core dump can provide me some more informations ? 2012-11-14T03:48:01.046Z cpu4:6089)0x41221f25ba08:[0x41803007abff]PanicvPanicInt@vmkernel#nover+0x56 stack: 0x3000000008, 0x41221f25ba 2012-11-14T03:48:01.046Z cpu4:6089)0x41221f25bae8:[0x41803007b4a7]Panic@vmkernel#nover+0xae stack: 0x2e067c00000010, 0x0, 0x1f25bb38, 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25bc18:[0x4180300a7823]TLBDoInvalidate@vmkernel#nover+0x45a stack: 0xca, 0x0, 0x0, 0x0, 0x0 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25bc68:[0x418030489e17]UserMem_CartelFlush@<None>#<None>+0xce stack: 0xcaa0b, 0x0, 0x0, 0x4 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25bd78:[0x41803048ab91]UserMemUnmapStateCleanup@<None>#<None>+0x58 stack: 0x0, 0x41221f25bd 2012-11-14T03:48:01.047Z cpu4:6089)0x41221f25be58:[0x41803048b97d]UserMemUnmap@<None>#<None>+0x104 stack: 0x41221f267000, 0x41221f25bf 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25be98:[0x41803048bf20]UserMem_Unmap@<None>#<None>+0xe3 stack: 0x426, 0x0, 0x41221f25bef8, 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25beb8:[0x4180304a5985]UW64VMKSyscallUnpackReleasePhysMemMap@<None>#<None>+0x18 stack: 0x10 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25bef8:[0x418030476791]User_LinuxSyscallHandler@<None>#<None>+0x17c stack: 0x41803004cc70, 2012-11-14T03:48:01.048Z cpu4:6089)0x41221f25bf18:[0x4180300a82be]User_LinuxSyscallHandler@vmkernel#nover+0x19 stack: 0x3ffe63bed80, 0 2012-11-14T03:48:01.049Z cpu4:6089)0x41221f25bf28:[0x418030110064]gate_entry@vmkernel#nover+0x63 stack: 0x10b, 0x0, 0x0, 0x426, 0xcf76 2012-11-14T03:48:01.049Z cpu4:6089)VMware ESXi 5.1.0 [Releasebuild-799733 x86_64] PCPU 1 locked up. Failed to ack TLB invalidate (total of 1 locked up, PCPU(s): 1). 2012-11-14T03:48:01.050Z cpu4:6089)cr0=0x80010031 cr2=0xcaa0b750 cr3=0x197d7b000 cr4=0x42768 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:0 world:6111 name:"vmm0:Windows_2012_-_SQL" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:1 world:6032 name:"vmm0:Windows_2012_-_AD" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:2 world:6098 name:"vmm0:Windows_2012_-_App" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:3 world:4099 name:"idle3" (IS) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:4 world:6089 name:"vmx-vcpu-0:NexentaStor" (U) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:5 world:6134 name:"vmm0:Ubuntu_-_NGINX" (V) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:6 world:4102 name:"idle6" (IS) 2012-11-14T03:48:01.050Z cpu4:6089)pcpu:7 world:4103 name:"idle7" (IS) 2012-11-14T03:48:01.050Z cpu4:6089)@BlueScreen: PCPU 1 locked up. Failed to ack TLB invalidate (total of 1 locked up, PCPU(s): 1).

    Read the article

  • JVM process resident set size "equals" max heap size, not current heap size

    - by Volune
    After a few reading about jvm memory (here, here, here, others I forgot...), I am expecting the resident set size of my java process to be roughly equal to the current heap space capacity. That's not what the numbers are saying, it seems to be roughly equal to the max heap space capacity: Resident set size: # echo 0 $(cat /proc/1/smaps | grep Rss | awk '{print $2}' | sed 's#^#+#') | bc 11507912 # ps -C java -O rss | gawk '{ count ++; sum += $2 }; END {count --; print "Number of processes =",count; print "Memory usage per process =",sum/1024/count, "MB"; print "Total memory usage =", sum/1024, "MB" ;};' Number of processes = 1 Memory usage per process = 11237.8 MB Total memory usage = 11237.8 MB Java heap # jmap -heap 1 Attaching to process ID 1, please wait... Debugger attached successfully. Server compiler detected. JVM version is 24.55-b03 using thread-local object allocation. Garbage-First (G1) GC with 18 thread(s) Heap Configuration: MinHeapFreeRatio = 10 MaxHeapFreeRatio = 20 MaxHeapSize = 10737418240 (10240.0MB) NewSize = 1363144 (1.2999954223632812MB) MaxNewSize = 17592186044415 MB OldSize = 5452592 (5.1999969482421875MB) NewRatio = 2 SurvivorRatio = 8 PermSize = 20971520 (20.0MB) MaxPermSize = 85983232 (82.0MB) G1HeapRegionSize = 2097152 (2.0MB) Heap Usage: G1 Heap: regions = 2560 capacity = 5368709120 (5120.0MB) used = 1672045416 (1594.586769104004MB) free = 3696663704 (3525.413230895996MB) 31.144272834062576% used G1 Young Generation: Eden Space: regions = 627 capacity = 3279945728 (3128.0MB) used = 1314914304 (1254.0MB) free = 1965031424 (1874.0MB) 40.089514066496164% used Survivor Space: regions = 49 capacity = 102760448 (98.0MB) used = 102760448 (98.0MB) free = 0 (0.0MB) 100.0% used G1 Old Generation: regions = 147 capacity = 1986002944 (1894.0MB) used = 252273512 (240.5867691040039MB) free = 1733729432 (1653.413230895996MB) 12.702574926293766% used Perm Generation: capacity = 39845888 (38.0MB) used = 38884120 (37.082786560058594MB) free = 961768 (0.9172134399414062MB) 97.58628042120682% used 14654 interned Strings occupying 2188928 bytes. Are my expectations wrong? What should I expect? I need the heap space to be able to grow during spikes (to avoid very slow Full GC), but I would like to have the resident set size as low as possible the rest of the time, to benefit the other processes running on the server. Is there a better way to achieve that? Linux 3.13.0-32-generic x86_64 java version "1.7.0_55" Running in Docker version 1.1.2 Java is running elasticsearch 1.2.0: /usr/bin/java -Xms5g -Xmx10g -XX:MinHeapFreeRatio=10 -XX:MaxHeapFreeRatio=20 -Xss256k -Djava.awt.headless=true -XX:+UseG1GC -XX:MaxGCPauseMillis=350 -XX:InitiatingHeapOccupancyPercent=45 -XX:+AggressiveOpts -XX:+UseCompressedOops -XX:-OmitStackTraceInFastThrow -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintClassHistogram -XX:+PrintTenuringDistribution -XX:+PrintGCApplicationStoppedTime -XX:+PrintGCApplicationConcurrentTime -Xloggc:/opt/elasticsearch/logs/gc.log -XX:+HeapDumpOnOutOfMemoryError -XX:HeapDumpPath=/opt elasticsearch/logs/heapdump.hprof -XX:ErrorFile=/opt/elasticsearch/logs/hs_err.log -Des.logger.port=99999 -Des.logger.host=999.999.999.999 -Delasticsearch -Des.foreground=yes -Des.path.home=/opt/elasticsearch -cp :/opt/elasticsearch/lib/elasticsearch-1.2.0.jar:/opt/elasticsearch/lib/*:/opt/elasticsearch/lib/sigar/* org.elasticsearch.bootstrap.Elasticsearch There actually are 5 elasticsearch nodes, each in a different docker container. All have about the same memory usage. Some stats about the index: size: 9.71Gi (19.4Gi) docs: 3,925,398 (4,052,694)

    Read the article

  • Migrate from MySQL to PostgreSQL on Linux (Kubuntu)

    - by Dave Jarvis
    Storyline Trying to migrate a database from MySQL to PostgreSQL. All the documentation I have read covers, in great detail, how to migrate the structure. I have found very little documentation on migrating the data. The schema has 13 tables (which have been migrated successfully) and 9 GB of data. MySQL version: 5.1.x PostgreSQL version: 8.4.x I want to use the R programming language to analyze the data using SQL select statements; PostgreSQL has PL/R, but MySQL has nothing (as far as I can tell). A long time ago in a galaxy far, far away... Create the database location (/var has insufficient space; also dislike having the PostgreSQL version number everywhere -- upgrading would break scripts!): sudo mkdir -p /home/postgres/main sudo cp -Rp /var/lib/postgresql/8.4/main /home/postgres sudo chown -R postgres.postgres /home/postgres sudo chmod -R 700 /home/postgres sudo usermod -d /home/postgres/ postgres All good to here. Next, restart the server and configure the database using these installation instructions: sudo apt-get install postgresql pgadmin3 sudo /etc/init.d/postgresql-8.4 stop sudo vi /etc/postgresql/8.4/main/postgresql.conf Change data_directory to /home/postgres/main sudo /etc/init.d/postgresql-8.4 start sudo -u postgres psql postgres \password postgres sudo -u postgres createdb climate pgadmin3 Use pgadmin3 to configure the database and create a schema. A New Hope The episode began in a remote shell known as bash, with both databases running, and the installation of a command with a most unusual logo: SQL Fairy. perl Makefile.PL sudo make install sudo apt-get install perl-doc (strangely, it is not called perldoc) perldoc SQL::Translator::Manual Extract a PostgreSQL-friendly DDL and all the MySQL data: sqlt -f DBI --dsn dbi:mysql:climate --db-user user --db-password password -t PostgreSQL > climate-pg-ddl.sql mysqldump --skip-add-locks --complete-insert --no-create-db --no-create-info --quick --result-file="climate-my.sql" --databases climate --skip-comments -u root -p The Database Strikes Back Recreate the structure in PostgreSQL as follows: pgadmin3 (switch to it) Click the Execute arbitrary SQL queries icon Open climate-pg-ddl.sql Search for TABLE " replace with TABLE climate." (insert the schema name climate) Search for on " replace with on climate." (insert the schema name climate) Press F5 to execute This results in: Query returned successfully with no result in 122 ms. Replies of the Jedi At this point I am stumped. Where do I go from here (what are the steps) to convert climate-my.sql to climate-pg.sql so that they can be executed against PostgreSQL? How to I make sure the indexes are copied over correctly (to maintain referential integrity; I don't have constraints at the moment to ease the transition)? How do I ensure that adding new rows in PostgreSQL will start enumerating from the index of the last row inserted (and not conflict with an existing primary key from the sequence)? Resources A fair bit of information was needed to get this far: https://help.ubuntu.com/community/PostgreSQL http://articles.sitepoint.com/article/site-mysql-postgresql-1 http://wiki.postgresql.org/wiki/Converting_from_other_Databases_to_PostgreSQL#MySQL http://pgfoundry.org/frs/shownotes.php?release_id=810 http://sqlfairy.sourceforge.net/ Thank you!

    Read the article

  • Lighttpd 403 Errors on HTML and PHP pages

    - by Brian
    I installed lighttpd on CentOS 5.5 64-bit. Everything seems fine and running except I cannot get past 403 errors on both HTML and PHP pages. I have used CHMOD and CHOWN, changed ownership in the config file, done everything possible and have been stuck for 2 days. Appreciate any help, and here's hoping to a stupid error on my part. Here is the log file with debug options on: 2011-02-21 11:23:13: (request.c.304) fd: 7 request-len: 408 GET /index.html HTTP/1.1 Host: 10.0.1.8 User-Agent: Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.13) Gecko/20101203 Firefox/3.6.13 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 115 Connection: keep-alive Cache-Control: max-age=0 2011-02-21 11:23:13: (response.c.241) run condition 2011-02-21 11:23:13: (response.c.300) -- splitting Request-URI 2011-02-21 11:23:13: (response.c.301) Request-URI : /index.html 2011-02-21 11:23:13: (response.c.302) URI-scheme : http 2011-02-21 11:23:13: (response.c.303) URI-authority: 10.0.1.8 2011-02-21 11:23:13: (response.c.304) URI-path : /index.html 2011-02-21 11:23:13: (response.c.305) URI-query : 2011-02-21 11:23:13: (response.c.349) -- sanatising URI 2011-02-21 11:23:13: (response.c.350) URI-path : /index.html 2011-02-21 11:23:13: (response.c.470) -- before doc_root 2011-02-21 11:23:13: (response.c.471) Doc-Root : /srv/www/lighttpd 2011-02-21 11:23:13: (response.c.472) Rel-Path : /index.html 2011-02-21 11:23:13: (response.c.473) Path : 2011-02-21 11:23:13: (response.c.521) -- after doc_root 2011-02-21 11:23:13: (response.c.522) Doc-Root : /srv/www/lighttpd 2011-02-21 11:23:13: (response.c.523) Rel-Path : /index.html 2011-02-21 11:23:13: (response.c.524) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.541) -- logical -> physical 2011-02-21 11:23:13: (response.c.542) Doc-Root : /srv/www/lighttpd 2011-02-21 11:23:13: (response.c.543) Rel-Path : /index.html 2011-02-21 11:23:13: (response.c.544) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.561) -- handling physical path 2011-02-21 11:23:13: (response.c.562) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.608) -- access denied 2011-02-21 11:23:13: (response.c.609) Path : /srv/www/lighttpd/index.html 2011-02-21 11:23:13: (response.c.128) Response-Header: HTTP/1.1 403 Forbidden Content-Type: text/html Content-Length: 345 Date: Mon, 21 Feb 2011 16:23:13 GMT Server: lighttpd/1.4.28 Here is the directory listing. I used CHOWN to set to lighttpd:lighttpd [root@localhost lighttpd]# ls -al total 40 drwxrwxrwx 2 lighttpd lighttpd 4096 Feb 21 10:48 . drwxrwxrwx 3 lighttpd lighttpd 4096 Feb 21 10:57 .. -rwxrwxrwx 1 lighttpd lighttpd 10 Feb 20 08:32 index.html -rwxrwxrwx 1 lighttpd lighttpd 20 Feb 21 10:48 index.php -rwxrwxrwx 1 lighttpd lighttpd 20 Feb 21 10:39 info.php [root@localhost lighttpd]# Requested Commands: [root@localhost lighttpd]# ls -ld / /srv /srv/www drwxr-xr-x 22 root root 4096 Feb 21 04:39 / drwxrwxrwx 3 lighttpd lighttpd 4096 Feb 20 07:38 /srv drwxrwxrwx 3 lighttpd lighttpd 4096 Feb 21 10:57 /srv/www [root@localhost lighttpd]# ps auxZ | grep lighttpd root:system_r:httpd_t lighttpd 3842 0.0 0.2 48368 896 ? S 12:24 0:00 /usr/sbin/lighttpd -f /etc/lighttpd/lighttpd.conf root:system_r:unconfined_t:SystemLow-SystemHigh root 3845 0.0 0.2 61152 764 pts/0 R+ 12:24 0:00 grep lighttpd

    Read the article

  • IIS7 dynamic_compression_not_success Reason 12

    - by Peter Oehlert
    So, I'm a bit of an IIS7 n00b but I've used most of the old IIS systems going back to 3. I'm trying to turn on dynamic compression and it's working, mostly. It doesn't work for my ADO.Net Data Service (Astoria) requests, batched or not. I found the freb tracing which was really helpful. And what I come up with unbatched requests is that it returns Reason Code 12, NO_MATCHING_CONTENT_TYPE. OK, so I don't have the matching mime type specified, that's easy. Except this is what I have in my web.config (which I think is correct, but maybe not). <httpCompression dynamicCompressionDisableCpuUsage="100" dynamicCompressionEnableCpuUsage="100" noCompressionForHttp10="false" noCompressionForProxies="false" noCompressionForRange="false" sendCacheHeaders="true" staticCompressionDisableCpuUsage="100" staticCompressionEnableCpuUsage="100"> <dynamicTypes> <clear/> <add mimeType="*/*" enabled="true" /> </dynamicTypes> <staticTypes> <clear/> <add mimeType="*/*" enabled="true" /> </staticTypes> </httpCompression> <urlCompression doDynamicCompression="true" doStaticCompression="true" dynamicCompressionBeforeCache="false" /> Now I think that this means it should compress any request that includes the Accept:Gzip header. I'd love to know what others might think here. My fiddler trace: GET /SecurityDataService.svc/GetCurrentAccount HTTP/1.1 Accept-Charset: UTF-8 Accept-Language: en-us dataserviceversion: 1.0;Silverlight Accept: application/atom+xml,application/xml maxdataserviceversion: 1.0;Silverlight Referer: http://sdev03/apptestpage.aspx Accept-Encoding: gzip, deflate User-Agent: Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.0; WOW64; Trident/4.0; SLCC1; .NET CLR 2.0.50727; .NET CLR 3.5.21022; .NET CLR 3.5.30729; InfoPath.2; .NET CLR 3.0.30729; OfficeLiveConnector.1.4; OfficeLivePatch.1.3) Host: sdev03 Connection: Keep-Alive Cookie: .ASPXAUTH=<snip> HTTP/1.1 200 OK Cache-Control: no-cache Content-Type: application/atom+xml;charset=utf-8 Server: Microsoft-IIS/7.0 DataServiceVersion: 1.0; X-AspNet-Version: 2.0.50727 X-Powered-By: ASP.NET Date: Mon, 22 Mar 2010 22:29:06 GMT Content-Length: 2726 <?xml version="1.0" encoding="utf-8" standalone="yes"?> *** <snip> removed ***

    Read the article

< Previous Page | 727 728 729 730 731 732 733 734 735 736 737 738  | Next Page >