Search Results

Search found 20592 results on 824 pages for 'anything'.

Page 74/824 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• diskmgmt.msc: Cannot delete volume from USB

  - by Notinlist

  I have an USB drive with about 8GB of size. It has a single partition of size 169MB. Don't know why, I got it that way. I wanted to delete this small (FAT32) partition and create a single NTFS volume on it. First, I noticed that the "Delete volumme" option is disabled (grayed out). I then tried "Change drive letter and paths..." and removed "F:", that way I made sure that there are no open files on it. The "Delete volume" was still disabled. Then I got suspicious, and right clicked on the "Unallocated" area and I noticed that I did not have any useful option. All "New * volume" items are disabled. I exited from diskmgmt.msc, ran a cmd.exe with administrator privileges, ran the diskmgmt.msc from it, same experiences. Why can't i do anything with this disk? I've read some advices about downloading some alternative free software, but I rather not do it if possible. I still hope that Windows 7 Enterprise 64bit alone can reinitialize an USB drive without external help. I also cannot do anything with my other 8GB pendrive. It's all an NTFS volume, I tried to delete it, but the option is disabled here too. Maybe I have some settings somewhere that prevents my from partitioning USB disks. (I have the freedom to remove my D: partition which is the second - not counding the "System reserved" - on my SSD disk.)

  Read the article

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• Get Safari to use different autocompletion on different URLs on same hostname

  - by Luke404

  I have a webserver publishing different services over the same SSL VirtualHost, the two most commonly used being PhpMyAdmin and Cacti. These (and others) use 'cookie' style authentication, asking user and password in an HTML form (thus not using HTTP Authentication). Being on the same hostname, the Safari browser didn't manage too well stored passwords: if I login to one app with user foo, and then go to app two it would propose me user foo and its password in the login form. Changing just the username to bar used to be sufficient to let Safari autocomplete the correct password in its form field. Annoying, but I could live with it - usernames are short and easy to remember when compared to the passwords we use. After the update to safari5 this seems to be no longer true: if I store in safari (actually user keychain on OSX) credentials for https://www.foobarbaz.com/app1 AND credentials for https://www.foobarbaz.com/app2 there seem to be no way for it to autocomplete both based on the url. Even editing the keychain to add the path (it will store only the hostname by default) does not help. Is there anything I can do to let it work the way I want while still keeping everything on one hostname? Modifying anything server side is of course possible, but I can't switch apps to HTTP Auth (and not every one will support it anyway) to use different 'realms'.

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Adding 2nd DC to the domain from a different subnet over VPN.

  - by EagerToLearn

  I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

  Read the article

• Sending mail results in "Sender address rejected: Domain not found"

  - by user1281413

  The setup: WHM/CPanel CentOS 5 server running Exim and Courier for mail services, and BIND for domain name services. I recently moved servers. The old server was running a HIGHLY similar configuration, and all accounts were ported via WHM. However, the server is unable to send, and sometimes receive email. Errors I am seeing (when I do get an error mail back) state: 450 4.1.8 : Sender address rejected: Domain not found Edit for clarity: this is the error response from remote mail servers. Numerous independent mail servers come back with the same error. (Email address is merely one valid example) My first instinct of course was to check the domain records. However, k-t.org appears to have a valid record (including an MX record), even after running it through domain checks on a completely different server elsewhere and online. Note that the issue appears to happen with all the domains hosted on the server, not just k-t.org I have also ensured that a PTR was created. My Googling has only lead me to people who had fairly basic DNS mistakes, but either I'm blind/dumb (possible, DNS is not my strong suite), or it's something that is a bit more archaic. I've run out of ideas, and I can't seem to find anything that could explain why servers are unable to resolve the domains. There doesn't seem to be anything missing or incorrect.

  Read the article

• Http-Only cookies in WebLogic: what versions support them/how and why are they supported?

  - by John

  We want to make all cookies set by our webapp http-only. I only have a basic understanding of the benefits of doing this but I'm told by security people that it's a Good Thing (tm) Our app is running under JDK1.6.05 and WebLogic10.3.0 After way too much digging around Oracle's website for documentation, I've found good evidence that the first version of WebLogic to support http-only cookies is 10.3.1. By "support," I mean the cookie-http-only deployment-descriptor element. Before we go about upgrading, I'd be nice to have these questions answered: 1a) Is it accurate that WL10.3.1 is the first version to support http-only cookies and that we're out of luck with 10.3.0? 1b) If we do indeed need to upgrade, is there an easy to do so under Windows? I've heard people mention an "upgrade jar" that you just stick in the classpath but I can't find any mention of this by Oracle. Does an easy way exist, or do we need to do a full-install of the new version? 2) What does the cookie-http-only deployment-descriptor element do when enabled? Will it ensure all cookies set by the application have an http-only=true attribute? Will it do more or less? Is there anything I'll have to do programmatically? 3) Is there anything in general I should know about http-only cookies, getting my web app to take advantage of them, or other security concerns?

  Read the article

• Printer spooler service stop running when sent print job

  - by Hanan N.

  Every time i am sending a print job to the printer, i am don't get any response from the printer, and at the printer job list at the status of the job, i see that there was an Error, but it don't give me any clue on what could be the problem. After some investigation i found that every time that i send the print job to the printer the printer spooler service stops to run, then after a second or two it start again (i think that this behavior is related to the printer spooler settings to rerun it self after it stops). Things that i have tried so far: Remove and Install again the Driver. After removing the driver, i have removed the unnecessary registry keys according to this article from Microsoft, these are: Rename all files and folders in: c:\windows\system32\spool\drivers\w32x86 Remove anything but Drivers Print and Processors: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environment\Windows NT x86 Remove anything in here: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors but: BJ Language Monitor Local Port Microsoft Document Imaging Writer Monitor Microsoft Shared Fax Monitor Standard TCP/IP Port USB Monitor WSD Port Disconnect and Reconnect the Printer. Clean the computer from Viruses & Spywares. Currently i am stuck, i have no more things to try, if anybody know about any kind of solution please let me know about it. Since i am want to keep this post as general problem that relate to the printer spooler, and not just my particular problem, i didn't included inside the windows version & the printer model, they are (although i think that it isn't relate just for that particular model): Windows 7 32bit, HP Officejet 4500 G510g-m (connect to the computer via USB). Thanks.

  Read the article

• I can't get my PC to start up by a normal way.

  - by ssice

  I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

  Read the article

• How to stop NAT dropping idle connections?

  - by WGH

  I have a TCP connection that can be idle for many hours. The traffic is flowing from the server to the client only. One might say it's kind of push notification. My home router, however, tends to drop the connection silently after 20 minutes (the value of /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established). The server detects the loss once it tries to send anything (I assume it receives RST from the router itself). As client never sends anything, it never detects the loss. RFC 5382 "NAT Behavioral Requirements for TCP" states the following: A NAT can check if an endpoint for a session has crashed by sending a TCP keep-alive packet and receiving a TCP RST packet in response. It makes sense. It's much more effective than sending keep-alives by the host itself (as only NAT knows its own timeout). And probably not hard to implement. Is there any NAT solutions implementing this? It would be great if there was a way to enable this in iptables.

  Read the article

• Converting PDF eBooks into a Kindle format

  - by Ender

  Over the past couple of years I've amassed quite a collection of guides, tutorials and ebooks in PDF format. A lot of these are quite useful for work, especially PDF documentation, and rather than have to be at a computer every time I want to read how to do something in Sitecore or to read through a software testing ebook I'd like to do it on my brand-spanking-new Kindle. However, even though there is now a native PDF reader on the Kindle due to the nature of PDF's they are practically unreadable. The text doesn't wrap due to how PDF's are sized and so far after a bunch of Google searches I've yet to find a viable solution to get my PDF's converted into a readable Kindle format. Sometimes these books have code or pictures/tables in them, but most of the time they're text-heavy and to be honest I'd be surprised if there wasn't a free tool to handle the converting of PDF to one of the (seemingly many) Kindle formats. So, can anyone help me out with this? EDIT: I've tried Calibre, and have checked their forums to play with some of the advanced settings, yet the solutions available seem to be extremely poor, especially if the book you're attempting to read contains equations, code, or anything outside of plain text. I've also tried Amazon's conversion service, which wasn't much help with such documents. The best way I have found so far is to build the entire thing over again in ePub or RTF format and convert to MOBI from there. This works for text-heavy books with tables, but anything technical still isn't covered. Can anyone help with this?

  Read the article

• What does "incoming" and "outgoing" traffic mean?

  - by mgibsonbr

  I've seen many resources explaining how to set up a server's firewall to allow incoming and outgoing traffic on HTTP standard ports (80 and 443), but I can't figure out why I would need either of them. Do I need to unblock both for a "regular" web site to work? For file uploads to work? Are there situations where it would be advisable to unblock one and leave the other blocked? Sorry if that's a basic question, but I couldn't find it explained anywhere (also I'm not a native english speaker). I know in a "regular" web site the client is always the one who initiates a request, so I'm assuming a web server must accept incoming traffic on those ports, and my common sense tells me the server is allowed to send a response without unblocking anything else (otherwise it wouldn't make sense to have two types of rules). Is that correct? But what is an outgoing web (service) traffic, and what would be its use? AFAIK if the server wanted to initiate a connection with another machine, the specific port that matters is the one in the other end (i.e. the destination port would be 80), on its end any free port could be used (the source port would be random). I can open HTTP requests from my server (using wget for instance) without unblocking anything. So I'm assuming my concepts of "incoming" and "outgoing" are wrong somehow.

  Read the article

• Which project management software for technophobes who've never worked with something like that?

  - by Ernst

  Hi, Our director has asked me to get something to manage projects. Note that so far we haven't used anything of the sort. I did not get very clear instructions yet, probably because she doesn't know exactly what we need either. My guess is, we'll only find out while using something. I've looked at some, openworkbench, ganttproject, and microsoft project. The latter has the advantage of easy importing of users from exchange, are there others that do that (even if not directly, easily)? I don't think it's a critical requirement though. We're using some other custom software where I have to add users manually anyway and we're small enough that it's maybe once a month that I have to add or remove a user. In any case, I'm not in favour of buying anything, since I'm skeptic about us actually succeeding in putting it to good use, and even if we do, we will only during usage discover what we need. We're also not a tech shop, most people vary from not very technically adept to technophobic. This means we need something very userfriendly. I prefer to stay away from online solutions, since we deal with sensitive information and I prefer to keep that in house, but I guess it would be acceptable for the trial period. An intranet site is an option though, but preferably something that is easy to set up with IIS. Xplanner plus and redmine I found too hard to set up for this experiment. Some other options I haven't yet tried to install, but which look to complex for our technophobes: Endeavour Software Project Management, Project-Open, Trac. Any suggestions? Thanks, Ernst

  Read the article

• Games, Windows 8.1 and 144Hz display

  - by Marioysikax

  So I have been having problems with few games after switching from 7 to 8.1, which seems to be related to my 144Hz monitor. Few examples: Shank, Shank 2, Blood of the Werewolf, Astebreed, the Sims 2 and Rayman Legends patch 1.2Had few other as well but it's been long and I have 600+ steam library. From those games at least the Sims 2 and Shank worked without any problems with same setup and Windows 7. So basically these games simply refuse to launch with basic setup. However if I plug 60Hz TV with HDMI instead everything magically starts to work. As for Astebreed and the Sims 2 using windowed mode seems to also work. As for Rayman Demo and version 1.0 works for some reason and 1.2 breaks settings menu. I have already tried contacting supports. EA support stated game simply shouldn't work with 8.1 at all (which is lie as it works with that TV and friend with 8 plays just fine), ubisoft support took few weeks and support said he will forward info for further processing, blood of the werewolf support had no idea what's going on and told me to just use my TV instead.Changing monitors refresh rate to 120Hz or forcing it to 60Hz doesn't do anything. I have DVI right now but I will try with DisplayPort when I get the cable. At PCGW Garrett said it may have something to do how listing resolutions work with 8 compared to earlier Windows versions but my googling skills don't bring anything up and compatibility mode for earlier windows version doesn't work either (not that I expected that to work). My system specs are on my steam profile. How do I get those work with my 144Hz monitor as well as possible future games having same problem? Downgrading to 7 would work but is far from practical and I don't own legit lisence for that one.

  Read the article

• PowerPoint 2007 slides are only partially converted to PDF since SP3

  - by Tim Pietzcker

  EDIT: Microsoft support has confirmed that it's a bug with PowerPoint 2007 SP3. I have recently encountered a problem with the "Save as PDF/XPS" add-in for PowerPoint 2007. When I use "Save as PDF/XPS" to create a PDF version of my presentation, some slides are only partially included in the resulting PDF file. For example, this: (download the PPTX file here) is reduced to this (in Adobe Reader X or Acrobat Pro X (both 10.1.1)): (download the PDF file here) So far, I have only encountered this with slides that contain animation elements, but which part of the elements remain in the PDF version appears not to have anything to do with the order in which the animated elements appear, so that might just be a coincidence. Update: The problem persists even if I "un-animate" the slides (removing the animation but leaving the previously animated elements intact). When viewing the affected slides in Acrobat Reader, it sometimes complains about the file containing invalid elements, and that I should complain to whoever generated the PDF file... Update 2: I have just installed Office 2007 on a new Windows 7 x64 PC. With the original Office version (12.0.4518.1014 MSO 12.0.6562.5003), a correct PDF file is generated. After installation of SP3 (12.0.6606.1000 SP3 MSO 12.0.6607.1000) a corrupt PDF file is generated. Today's Microsoft Updates (to PowerPoint version 12.0.6654.5000) haven't changed anything, by the way. Update 3: I have opened a tech support incident with Microsoft. They have confirmed the "limitation", as they called it, and it is indeed limited to 2007 SP 3 only. They are going to pass it on to the developers but they can't say when or even if a fix would be forthcoming, so I guess I'll upgrade to 2010...

  Read the article

• S.M.A.R.T. broken sectors

  - by Jeffrey Vandenborne

  Recently I received my hard drive (LaCie) that I've sent away for warranty, my disk failed, and I used Palimpsest Disk utility to check if anything was wrong in the S.M.A.R.T Status. And it said that there were a few broken sectors. So the next day, I went to the store and told the story. 4 weeks later I actually got my drive back. The first thing I did was plugging it in and starting the disk utility, and weirdly it showed me pretty much the exact same things, even the values of most tests were the same as they were before when my drive broke. The serial number is different though, but it does show a very peculiar value. Now I'm wondering, I'm almost sure it's the exact same drive and it still says I've got broken sectors, does it just say that because it has been cached in the drive somewhere while LaCie DID actually fix it? Or should I run the extended self test (which seems to take hours) first? Also I've tried the smartctl command tool, it says the drive has smart support, but it doesn't show anything, it says that it's enabled, but then it says that it's disabled, picture below The picture of the Disk utility: Thanks in advance

  Read the article

• Creating a bootable USB drive from a distro split over two DVD ISOs

  - by Kev

  I am searching and not finding the right way to do this. Please note, I don't think I'm trying for anything strange here. I just want to make a bootable USB stick of a single OS that happens to be larger than one DVD and happens to be larger than FAT32 will allow for in a single file. On our slow connection I spent a long time downloading CentOS 5.9's two DVD ISOs: CentOS-5.9-x86_64-bin-DVD-1of2.iso (4.4 GB) CentOS-5.9-x86_64-bin-DVD-2of2.iso (718 MB) I have a USB stick that I want to somehow get these two ISOs on. Since the first one is 4.4 GB, I can't use ISO2USB because it insists on FAT32. I cannot find an alternative that lets you specify more than one ISO image--of the same distro, I'm not trying for some fancy multi-boot thing--to put on the same stick. I guess I should have downloaded the CD ISOs, but I thought I was "saving time" because then I wouldn't have as many files to run through the md5 checker. There's no IMG file of the whole thing (only a net install version, which I don't want--I want to pre-download everything) otherwise I would've gone for that. So, given that I have these two DVD ISOs, how can I get them on a stick that will boot and make use of both of them properly to install CentOS somewhere? Again, I don't think this is anything out of the ordinary, yet I can't find software/docs that seem to support this. Am I stuck re-downloading everything in CD-sized ISOs just to do this? I found this, but it doesn't run on Windows. I am using Windows to prepare the stick.

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• Router reporting failed admin login attempts from home server

  - by jeffora

  I recently noticed in the logs of my home router that it relatively regularly lists the following entry: [admin login failure] from source 192.168.0.160, Monday, June 20,2011 18:13:25 192.168.0.160 is the internal address of my home server, running Windows Home Server 2011. Is there anyway I can find out what specifically is trying to login to the router? Or is there some explanation for this behaviour? (not sure if this belongs here or on superuser...) [Update] I've run both Wireshark and netmon for a while on my home server. Wireshark captured the traffic, but didn't really show anything useful (or nothing I could make use of). A simple HTTP GET request is sent from the server (192.168.0.160) to the router (192.168.0.1), from a seemingly random port (I've seen examples from 50068, 52883), and it appears to do it twice in quick succession (incrementing port by 1), about every hour. Running netstat around the time of the failure didn't show anything (probably too long after anyway). I tried using netmon as it categorises by process, so I thought it might show a corresponding process for the port. Unfortunately, this comes in under the 'unknown' category, meaning it's basically just a slower, less useful Wireshark. I know there's not much to go on here, but does this help in anyway?

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• Windows Server 2008 - RAID 5 Fails on Reboot

  - by Adam

  Hey, I've got an install of Windows Server 2008 Enterprise. It's running software RAID-5 with five disks. The disks were originally formatted under Windows Server 2003, but came up fine once I installed Windows Server 2008. The issue I'm having is that every time I reboot the server, the RAID comes up with a "Failed Redundancy" - the data stays available. I have 4 disks on a PCI SATA controller, and one of the disks connected to the motherboard's on-board SATA ports. (The other on-board port has the system disk connected.) I was having Disk #4 fail consistently, so I tried swapping the cables on the controller end. I swapped the on-board RAID disk with one on the PCI controller. Same issue now, expect with disk #1. Once the system's up, I can reactivate the RAID, it will resync for a while, then go to "Healthy", and will stay that way for an indefinite amount of time - until I reboot. As soon as I reboot, the disk drops again. I've ruled out disk + cable with the recabling. I don't believe it would be the controller as it seems to work fine most of the time - only failing on reboot, and the other port on the same controller connects the system disk - which is clearly working. I did look in the event log, but didn't see anything particularly relevant (although I didn't know what I was looking for - just looked for anything with a "Warning" or "Error" symbol that looked disk-related :)). I'm not particularly familiar with RAID on Windows, does anyone have any idea why this might be doing this? Any idea how to fix it? Any suggestions appreciated! -- Adam

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• HP Laptop recognizes hard drive just long enough to install windows

  - by Joe

  I have an HP laptop, DV6500 (CTO). It refused to boot one day, so I ran some diagnostics (a friend lent me "Hirens Boot Disk", "UBCD" and "PC DR 6"). Everything passed, except for the hdd. I replaced the HDD with a used drive of unknown condition. Installed windows with no problems. Installed the wireless driver, tried to reboot ... no luck. So I went to Best Buy, bought a brand new Western Digital 320gb HDD. Put it in the machine, installed windows (vista home premium). Installed the wired networking driver. Tried to reboot. No luck. Put the first hdd back in the machine, reinstalled windows. Started to install some drivers, went to reboot, and the machine won't come back to life. Put the second hdd in the machine, rinse wash and repeat. I've replaced the memory, even though it passed diagnostics. Problem exists with both brand new memory, and old memory. The BIOS recognizes the hard drive. The computer freezes directly after the bios splash screen, and there is no hard drive activity light. I've tried two linux live distros (gentoo and ubuntu). Neither would run on this laptop, but will on a different HP laptop. UBCD and Hirens Boot Disk both ran, as did PC Doctor 6 which refuses to test anything (gets stuck at "enumerating hard disks"). Is there anything else I can try?

  Read the article

• Two screens hooked to one laptop

  - by mplacona

  Hi, I'm thinking of getting rid of my desktop, and using my (much better) laptop instead. I'm only wondering if I would be able to hook the two screens I have with it, so I'd end up with three screens. I've seen people doing it to desktops, but am not sure the same could be accomplished with a laptop. My laptop is a sony vaio, and it's got both a VGA output, and an HDMI output. It'd be great is I could simply hook two screens to it, and have three independent screens (not mirrored). on my desktop, I have pretty much the same thing, but with an extra DVI port. I connect the DVI to one screen, and the VGA to an older one. Trying to connect anything to the HDMI simply mirrors whatever is on the DVI (I've tried it a long time ago) So I was wondering if with the laptop I'd be able to do it, and end up with three independent screens. I don't know if there's anything else I could be using instead (i.e. any extra hardware), so recommendations are more than welcome. Thanks in advance, Marcos

  Read the article

• How to install/configure ffmpeg to compress mp4 videos for flash player delivery?

  - by Andrew Fulton

  We have a flash web-app that created interactive video, and are using ffmpeg to do some compression/resizing when a user "publishes" their project. The user can upload flv files and mp4 files, both of which play fine in the Flash UI before publishing. After publishing the flv files work fine, but the mp4 files will not play in the flash player: Audio will play but video won't. The mp4 files will play fine if I download them and play them in the Quicktime player but if I attempt to open them in the Adobe Media Player it reports "The media file does not contain a supported video track". If I open the Movie inspector in quicktime it tells me that the original file is an "h264" video and the ffmpeg-processed ones are "mpeg-4". I have tried forcing it to h264 by adding flags like -f h264 and -vcodec h264 but I get a screenfull of errors (no frame, illegal POC type, sps_id out of range) ending with Could not find codec parameters (Video: h264) h264 will show up if I run ffmpeg -formats and ffmpeg -codecs, and as I said it will play fine in Quicktime. Is there anything else I need to do to convince the flash player to play them? Is there anything else I need to tell you about the server that will help?

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >