Search Results

Search found 19925 results on 797 pages for 'retro software'.

Page 765/797 | < Previous Page | 761 762 763 764 765 766 767 768 769 770 771 772  | Next Page >

• Controling virtualbox internet access?

  - by HandyGandy

  I am finally going through the process of moving my XP into a vbox (host linux). The thing is that I am migrating a virtually clean install. So aside from the occasional antivirus scan, I want to make sure that my XP is not sending malware data (keystoke.logs, spam etc. ) out silently ( and thus having picked up some virus ). To that end I want to limit XP to contacting my LAN and a few internet sites. ( mainly sites that require proprietary windows only software to access, AV sites and Windows update ). I want XP to only access preapproved addresses. If it is trying to contact a nonapproved address, I want it somehow logged and access restricted until I allow access. I also don't want to have to decide whether to allow access to a site at my leisure. To keeps things clear let me give an example: I start my vbox/XP ( which I call MYXP) running on my linux box ( called MYLINUX connecting to the net through a linksys wrt54g ) and connects via samba to my LAN ( since my LAN seems to be possessed of every evil thing, it's address is 192.168.666. ). At the moment my configuration is set so that I allow MYXP to access 192.168.666 and www.MYANTIVIRUS_UPDATES.com and www.MS_UPDATES.com. Then on the VM I start a program which tries to make a connection to www.playmygame.com . www.playmygame.com is on my preapproved list so the connection goes through. Later I check attempted accesses and discover that it also tried to connect to www.mygame_high_scores.com I figure this is OK so I add www.mygame_high_scores.com to my approved list. Later, I again check address and discover that my VM/XP tried to access www.mygame_steals_your_identity.com. I do some checking and discover the address is registered to someone in Kiev, Nigeria. Since this doesn't sound kosher to me, I replace the MYXP VM with one that was backed up before I installed mygame. I remove www.playmygame.com and www.mygame_high_scores.com from my access list for MYXP. It should acomplish this with little overheard. When I am not running the VM ideally it should not have any overhead. Suggestions?

  Read the article

• Is the Scala 2.8 collections library a case of "the longest suicide note in history" ?

  - by oxbow_lakes

  First note the inflammatory subject title is a quotation made about the manifesto of a UK political party in the early 1980s. This question is subjective but it is a genuine question, I've made it CW and I'd like some opinions on the matter. Despite whatever my wife and coworkers keep telling me, I don't think I'm an idiot: I have a good degree in mathematics from the University of Oxford and I've been programming commercially for almost 12 years and in Scala for about a year (also commercially). I have just started to look at the Scala collections library re-implementation which is coming in the imminent 2.8 release. Those familiar with the library from 2.7 will notice that the library, from a usage perspective, has changed little. For example... > List("Paris", "London").map(_.length) res0: List[Int] List(5, 6) ...would work in either versions. The library is eminently useable: in fact it's fantastic. However, those previously unfamiliar with Scala and poking around to get a feel for the language now have to make sense of method signatures like: def map[B, That](f: A => B)(implicit bf: CanBuildFrom[Repr, B, That]): That For such simple functionality, this is a daunting signature and one which I find myself struggling to understand. Not that I think Scala was ever likely to be the next Java (or /C/C++/C#) - I don't believe its creators were aiming it at that market - but I think it is/was certainly feasible for Scala to become the next Ruby or Python (i.e. to gain a significant commercial user-base) Is this going to put people off coming to Scala? Is this going to give Scala a bad name in the commercial world as an academic plaything that only dedicated PhD students can understand? Are CTOs and heads of software going to get scared off? Was the library re-design a sensible idea? If you're using Scala commercially, are you worried about this? Are you planning to adopt 2.8 immediately or wait to see what happens? Steve Yegge once attacked Scala (mistakenly in my opinion) for what he saw as its overcomplicated type-system. I worry that someone is going to have a field day spreading fud with this API (similarly to how Josh Bloch scared the JCP out of adding closures to Java). Note - I should be clear that, whilst I believe that Josh Bloch was influential in the rejection of the BGGA closures proposal, I don't ascribe this to anything other than his honestly-held beliefs that the proposal represented a mistake.

  Read the article

• XML Parsing Error - C#

  - by Indebi

  My code is having an XML parsing error at line 7 position 32 and I'm not really sure why Exact Error Dump 5/1/2010 10:21:42 AM System.Xml.XmlException: An error occurred while parsing EntityName. Line 7, position 32. at System.Xml.XmlTextReaderImpl.Throw(Exception e) at System.Xml.XmlTextReaderImpl.Throw(String res, Int32 lineNo, Int32 linePos) at System.Xml.XmlTextReaderImpl.HandleEntityReference(Boolean isInAttributeValue, EntityExpandType expandType, Int32& charRefEndPos) at System.Xml.XmlTextReaderImpl.ParseAttributeValueSlow(Int32 curPos, Char quoteChar, NodeData attr) at System.Xml.XmlTextReaderImpl.ParseAttributes() at System.Xml.XmlTextReaderImpl.ParseElement() at System.Xml.XmlTextReaderImpl.ParseElementContent() at System.Xml.XmlTextReaderImpl.Read() at System.Xml.XmlLoader.LoadNode(Boolean skipOverWhitespace) at System.Xml.XmlLoader.LoadDocSequence(XmlDocument parentDoc) at System.Xml.XmlLoader.Load(XmlDocument doc, XmlReader reader, Boolean preserveWhitespace) at System.Xml.XmlDocument.Load(XmlReader reader) at System.Xml.XmlDocument.Load(String filename) at Lookoa.LoadingPackages.LoadingPackages_Load(Object sender, EventArgs e) in C:\Users\Administrator\Documents\Visual Studio 2010\Projects\Lookoa\Lookoa\LoadingPackages.cs:line 30 Xml File, please note this is just a sample because I want the program to work before I begin to fill this repository <repo> <Packages> <TheFirstPackage id="00001" longname="Mozilla Firefox" appver="3.6.3" pkgver="0.01" description="Mozilla Firefox is a free and open source web browser descended from the Mozilla Application Suite and managed by Mozilla Corporation. A Net Applications statistic put Firefox at 24.52% of the recorded usage share of web browsers as of March 2010[update], making it the second most popular browser in terms of current use worldwide after Microsoft's Internet Explorer." cat="WWW" rlsdate="4/8/10" pkgloc="http://google.com"/> </Packages> <categories> <WWW longname="World Wide Web" description="Software that's focus is communication or primarily uses the web for any particular reason."> </WWW> <Fun longname="Entertainment & Other" description="Music Players, Video Players, Games, or anything that doesn't fit in any of the other categories."> </Fun> <Work longname="Productivity" description="Application's commonly used for occupational needs or, stuff you work on"> </Work> <Advanced longname="System & Security" description="Applications that protect the computer from malware, clean the computer, and other utilities."> </Advanced> </categories> </repo> Small part of C# Code //Loading the Package and Category lists //The info from them is gonna populate the listboxes for Category and Packages Repository.Load("repo.info"); XmlNodeList Categories = Repository.GetElementsByTagName("categories"); foreach (XmlNode Category in Categories) { CategoryNumber++; CategoryNames[CategoryNumber] = Category.Name; MessageBox.Show(CategoryNames[CategoryNumber]); } The Messagebox.Show() is just to make sure it's getting the correct results

  Read the article

• Generate reasonable length license key with asymmetric encryption?

  - by starkos

  I've been looking at this all day. I probably should have walked away from it hours ago; I might be missing something obvious at this point. Short version: Is there a way to generate and boil down an asymmetrically encrypted hash to a reasonable number of unambiguous, human readable characters? Long version: I want to generate license keys for my software. I would like these keys to be of a reasonable length (25-36 characters) and easily read and entered by a human (so avoid ambiguous characters like the number 0 and the capital letter O). Finally--and this seems to be the kicker--I'd really like to use asymmetric encryption to make it more difficult to generate new keys. I've got the general approach: concatenate my information (user name, product version, a salt) into a string and generate a SHA1() hash from that, then encrypt the hash with my private key. On the client, build the SHA1() hash from the same information, then decrypt the license with the public key and see if I've got a match. Since this is a Mac app, I looked at AquaticPrime, but that generates a relatively large license file rather than a string. I can work with that if I must, but as a user I really like the convenience of a license key that I can read and print. I also looked at CocoaFob which does generate a key, but it is so long that I'd want to deliver it as a file anyway. I fooled around with OpenSSL for a while but couldn't come up with anything of a reasonable length. So...am I missing something obvious here? Is there a way to generate and boil down an asymmetrically encrypted hash to a reasonable number of unambiguous, human readable characters? I'm open to buying a solution. But I work on a number of different of platforms, so I'd want something portable. Everything I've looked at so far has been platform specific. Many, many thanks for a solution! PS - Yes, I know it will still be cracked. I'm trying to come up with something reasonable that, as a user, I would still find friendly.

  Read the article

• How to use CFNetwork to get byte array from sockets?

  - by Vic

  Hi, I'm working in a project for the iPad, it is a small program and I need it to communicate with another software that runs on windows and act like a server; so the application that I'm creating for the iPad will be the client. I'm using CFNetwork to do sockets communication, this is the way I'm establishing the connection: char ip[] = "192.168.0.244"; NSString *ipAddress = [[NSString alloc] initWithCString:ip]; /* Build our socket context; this ties an instance of self to the socket */ CFSocketContext CTX = { 0, self, NULL, NULL, NULL }; /* Create the server socket as a TCP IPv4 socket and set a callback */ /* for calls to the socket's lower-level connect() function */ TCPClient = CFSocketCreate(NULL, PF_INET, SOCK_STREAM, IPPROTO_TCP, kCFSocketDataCallBack, (CFSocketCallBack)ConnectCallBack, &CTX); if (TCPClient == NULL) return; /* Set the port and address we want to listen on */ struct sockaddr_in addr; memset(&addr, 0, sizeof(addr)); addr.sin_len = sizeof(addr); addr.sin_family = AF_INET; addr.sin_port = htons(PORT); addr.sin_addr.s_addr = inet_addr([ipAddress UTF8String]); CFDataRef connectAddr = CFDataCreate(NULL, (unsigned char *)&addr, sizeof(addr)); CFSocketConnectToAddress(TCPClient, connectAddr, -1); CFRunLoopSourceRef sourceRef = CFSocketCreateRunLoopSource(kCFAllocatorDefault, TCPClient, 0); CFRunLoopAddSource(CFRunLoopGetCurrent(), sourceRef, kCFRunLoopCommonModes); CFRelease(sourceRef); CFRunLoopRun(); And this is the way I sent the data, which basically is a byte array /* The native socket, used for various operations */ // TCPClient is a CFSocketRef member variable CFSocketNativeHandle sock = CFSocketGetNative(TCPClient); Byte byteData[3]; byteData[0] = 0; byteData[1] = 4; byteData[2] = 0; send(sock, byteData, strlen(byteData)+1, 0); Finally, as you may have noticed, when I create the server socket, I registered a callback for the kCFSocketDataCallBack type, this is the code. void ConnectCallBack(CFSocketRef socket, CFSocketCallBackType type, CFDataRef address, const void *data, void *info) { // SocketsViewController is the class that contains all the methods SocketsViewController *obj = (SocketsViewController*)info; UInt8 *unsignedData = (UInt8 *) CFDataGetBytePtr(data); char *value = (char*)unsignedData; NSString *text = [[NSString alloc]initWithCString:value length:strlen(value)]; [obj writeToTextView:text]; [text release]; } Actually, this callback is being invoked in my code, the problem is that I don't know how can I get the data that the windows client sent me, I'm expecting to receive an array of bytes, but I don't know how can I get those bytes from the data param. If anyone can help me to find a way to do this, or maybe me point me to another way to get the data from the server in my client application I would really appreciate it. Thanks.

  Read the article

• Where to put a glossary of important terms and patterns in documentation?

  - by Tetha

  Greetings. I want to document certain patterns in the code in order to build up a consistent terminology (in order to easen communication about the software). I am, however, unsure, where to define the terms given. In order to get on the same level, an example: I have a code generator. This code generator receives a certain InputStructure from the Parser (yes, the name InputStructure might be less than ideal). This InputStructure is then transformed into various subsequent datastructures (like an abstract description of the validation process). Each of these datastructures can be either transformed into another value of the same datastructure or it can be transformed into the next datastructure. This should sound like Pipes and Filters to some degree. Given this, I call an operation which takes a datastructures and constructs a value of the same datastructure a transformation, while I call an operation which takes a datastructure and produces a different follow-up datastructure a derivation. The final step of deriving a string containing code is called emitting. (So, overall, the codegenerator takes the input-structure and transforms, transforms, derives, transforms, derives and finally emits). I think emphasizing these terms will be benefitial in communications, because then it is easy to talk about things. If you hear "transformation", you know "Ok, I only need to think about these two datastructures", if you hear "emitting", you know "Ok, I only need to know this datastructure and the target language.". However, where do I document these patterns? The current code base uses visitors and offers classes called like ValidatorTransformationBase<ResultType> (or InputStructureTransformationBase<ResultType>, and so one and so on). I do not really want to add the definition of such terms to the interfaces, because in that case, I'd have to repeat myself on each and every interface, which clearly violates DRY. I am considering to emphasize the distinction between Transformations and Derivations by adding further interfaces (I would have to think about a better name for the TransformationBase-classes, but then I could do thinks like ValidatorTransformation extends ValidatorTransformationBase<Validator>, or ValidatorDerivationFromInputStructure extends InputStructureTransformation<Validator>). I also think I should add a custom page to the doxygen documentation already existing, as in "Glossary" or "Architecture Principles", which contains such principles. The only disadvantage of this would be that a contributor will need to find this page in order to actually learn about this. Am I missing possibilities or am I judging something wrong here in your opinion? -- Regards, Tetha

  Read the article

• Unable to add SSH pub key for GitHub

  - by Kaushik

  I am trying to set up a new GitHub account as part of learning ruby on rails. My OS is windows. I am having the following problem while trying to add my public key to the GitHub SSH public keys. When I put the key in the text area, supply a name, and click 'Add Key', I am taken to the Job profile page without any confirmation that the key has been added.(I am using SSH client GUI to generate RSA keys). When I come back to the SSH public keys page, I see that the key is not there. I tried this multiple times...without any result. Just as a test, I tried to ssh to the GitHub account using 'ssh -v [email protected]' and here is the verbose output: OpenSSH_4.6p1, OpenSSL 0.9.8e 23 Feb 2007 debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug1: identity file /c/Users/Administrator/.ssh/identity type -1 debug1: identity file /c/Users/Administrator/.ssh/id_rsa type -1 debug1: identity file /c/Users/Administrator/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5github2 debug1: match: OpenSSH_5.1p1 Debian-5github2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_4.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'github.com' is known and matches the RSA host key. debug1: Found key in /c/Users/Administrator/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /c/Users/Administrator/.ssh/identity debug1: Trying private key: /c/Users/Administrator/.ssh/id_rsa debug1: Trying private key: /c/Users/Administrator/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). Also, why is it looking for the keys in c/Users/Administrator/.ssh/ Is there a possibility of changing this default location? EDIT: With Mozila, I get error msg: Oops! The key has already been taken. The key is invalid. It must begin with 'ssh-rsa' or 'ssh-dss'. My key looks like: ---- BEGIN SSH2 PUBLIC KEY ---- Comment: "[2048-bit rsa, Administrator@Kaushik-THINK, Sun Jan 02 2011 \ 02:40:03]" AAAAB3NzaC1yc2EAAAADAQABAAABAQDoA5xqJozKmAHTGh9hgmagsFOl2hdPzS8ZPV9Ta1 xU0JiUnHef38Rvz/5oqL1wW7SjmZbc/+tCPOfU1lg3UisFXajJhek2bjJ2qsKd4Sjax2Nj ZMYD7djPb8rokUYSKW3bdYyJHtJH+murz04UGdCcZ8HqkMTzqlh3zAIK7SIlCy+mtAi5A/ sm0JbqlNGHB6YrL1aWIcOSolIx2HWt8cWhlK77guT9dPgd0HT59Gn0uhO7UWGLrNdJut0x ian3HdvNYMUXoO/SkNlxvWRgZ1UOhaB+qf4hw5RCGcBbqP3fM4LKpurHZx4wEpgmM0e4EM +2PYdf46uxChNdBl7J5sZF ---- END SSH2 PUBLIC KEY ---- I still can't see the key..so not sure how it says it is already taken.

  Read the article

• How to embed html table into the bpdy of email

  - by Michael Mao

  Hi all: I am sending info to target email via PHP native mail() method right now. Everything else works fine but the table part troubles me the most. See sample output : Dear Michael Mao : Thank you for purchasing flight tickets with us, here is your receipt : Your tickets will be delivered by mail to the following address : Street Address 1 : sdfsdafsadf sdf Street Address 2 : N/A City : Sydney State : nsw Postcode : 2 Country : Australia Credit Card Number : *************1234 Your purchase details are recorded as : <table><tr><th class="delete">del?</th><th class="from_city">from</th><th class="to_city">to</th><th class="quantity">qty</th><th class="price">unit price</th><th class="price">total price</th></tr><tr class="evenrow" id="Sydney-Lima"><td><input name="isDeleting" type="checkbox"></td><td>Sydney</td><td>Lima</td><td>1</td><td>1030.00</td><td>1030</td></tr><tr class="oddrow" id="Sydney-Perth"><td><input name="isDeleting" type="checkbox"></td><td>Sydney</td><td>Perth</td><td>3</td><td>340.00</td><td>1020</td></tr><tr class="totalprice"><td colspan="5">Grand Total Price</td><td id="grandtotal">2050</td></tr></table> The source of table is directly taken from a webpage, exactly as the same. However, Gmail, Hotmail and most of other emails will ignore to render this as a table. So I am wondering, without using Outlook or other email sending agent software, how could I craft a embedded table for the PHP mail() method to send? Current code snippet corresponds to table generation : $purchaseinfo = $_POST["purchaseinfo"]; //if html tags are not to be filtered in the body of email $stringBuilder .= "<table>" .stripslashes($purchaseinfo) ."</table>"; //must send json response back to caller ajax request if(mail($email, 'Your purchase information on www.hardlyworldtravel.com', $emailbody, $headers)) echo json_encode(array("feedback"=>"successful")); else echo json_encode(array("feedback"=>"error")); Any hints and suggestions are welcomed, thanks a lot in advance.

  Read the article

• Sysadmin 101: How can I figure out why my server crashes and monitor performance?

  - by bflora

  I have a Drupal-powered site that seems to have neverending performance problems. It was butt-slow about 5 months ago. I brought in some guys who installed nginx for anonymous visitors, ajaxified a few queries so they wouldn't fire during page load, and helped me find a few bottlenecks in the code. For about a month, the site was significantly faster, though not "fast" by any stretch of the word. Meanwhile, I'm now shelling out $400/month to Slicehost to host a site that gets less than 5,000/uniques a day. Yes, you read that right. Go Drupal. Recently the site started crashing again and is slow again. I can't afford to hire people to come in, study my code from top to bottom, and make changes that may or may not help anymore. And I can't afford to throw more hardware at the problem. So I need to figure out what the problem is myself. Questions: When apache crashes, is it possible to find out what caused it to crash? There has to be a way, right? If so, how can I do this? Is there software I can use that will tell me which process caused my server to die? (e.g. "Apache crashed because someone visited page X." or "Apache crashed because you were importing too many RSS items from feed X.") There's got to be a way to learn this, right? What's a good, noob-friendly way to monitor my current apache performance? My developer friends tell me to "just use Top, dude," but Top shows me a bunch of numbers without any context. I have no clue what qualifies as a bad number or a good number in Top, or which processes are relevant and which aren't. Are there any noob-friendly server monitoring tools out there? Ideally, I could have a page that would give me a color-coded indicator about how apache is performing and then show me a list of processes or pages that are sucking right now. This way, I could know when performance is bad and then what's causing it to be so bad. Why does PHP memory matter? My apparently has a 30MB memory foot print. Will it run faster if I bring that number down? Thanks for any advice. I spent a year or so trying to boost my advertising income so I could hire a contractor to solve my performance woes. I didn't want to have to learn all this sysadmin voodoo. I'm now resigned to the fact that might not have a choice.

  Read the article

• How do you attract programmers in rural areas?

  - by Reed Copsey

  I run a software development group for a very small, but stable and established company in a small town, somewhat outside of the "big city". Unfortunately, the "programmer" labor pool is much smaller due to the size of the city. There are many positives to working in this area, especially in terms of quality of life (particularly for people interested in outdoor activities), lower cost of living, great schools and neighborhoods, etc. However, I've always had difficulty attracting high-qualtiy, experienced developers. For those of you who hire developers outside of large cities: Where do you advertise to find good developers? Many of the large sites are very focused in certain metropolitan areas, and seem inappropriate places to advertise if you're outside of that main region. How do you attract quality developers to rural (or at least less metropolitan) locations? Do you find that you make more sacrifices in your hiring due to a smaller labor pool? Or do you just wait, and take extra time to attract people? What sacrifices do you expect to make if you are outside of the main developer-rich cities? For all of the developers out there... What would entice you to working in a smaller town? Are there things that would stand out and make you willing to relocate or at least apply to a position that was not nearby? What specific qualities would help you want to move outside of the city? In the past, I've had difficulty with finding good people. Most of the people who've applied and been willing to move out to a more rural location seem like the types that can't keep a quality job elsewhere. I'd like to know what advice people have to attracting quality technical staff. I don't believe its the work itself that's been the problem - The work is both interesting and challenging, and nearly 100% new development. The developers I have seem very happy with their situation - they love the work, the atmosphere, etc. It's more a matter of finding willing, able developers. Edit: More info after the first couple of answers: Right now, some of my best developers telecommute (some work from overseas); however, for this question, I'm trying to figure out how to get people who want to live and work full time locally. I need some people with whom I interact every day.

  Read the article

• Help with storing/accessing user access roles C# Winforms

  - by user222453

  Hello, firstly I would like to thank you in advance for any assistance provided. I am new to software development and have designed several Client/Server applications over the last 12 months or so, I am currently working on a project that involves a user logging in to gain access to the application and I am looking at the most efficient and "simple" method of storing the users permissions once logged in to the application which can be used throughout restricting access to certain tabs on the main form. I have created a static class called "User" detailed below: static class User { public static int _userID; public static string _moduleName; public static string _userName; public static object[] UserData(object[] _dataRow) { _userID = (int)_dataRow[0]; _userName = (string)_dataRow[1]; _moduleName = (string)_dataRow[2]; return _moduleName; } } When the user logs in and they have been authenticated, I wish to store the _moduleName objects in memory so I can control which tabs on the main form tab control they can access, for example; if the user has been assigned the following roles in the database: "Sales Ledger", "Purchase Ledger" they can only see the relevant tabs on the form, by way of using a Switch - Case block once the login form is hidden and the main form is instantiated. I can store the userID and userName variables in the main form once it loads by means of say for example: Here we process the login data from the user: DataAccess _dal = new DataAccess(); switch (_dal.ValidateLogin(txtUserName.Text, txtPassword.Text)) { case DataAccess.ValidationCode.ConnectionFailed: MessageBox.Show("Database Server Connection Failed!"); break; case DataAccess.ValidationCode .LoginFailed: MessageBox.Show("Login Failed!"); _dal.RecordLogin(out errMsg, txtUserName.Text, workstationID, false); break; case DataAccess.ValidationCode .LoginSucceeded: frmMain frmMain = new frmMain(); _dal.GetUserPrivList(out errMsg,2); //< here I access my DB and get the user permissions based on the current login. frmMain.Show(); this.Hide(); break; default: break; } private void frmMain_Load(object sender, EventArgs e) { int UserID = User._userID; } That works fine, however the _modules object contains mutiple permissions/roles depending on what has been set in the database, how can I store the multiple values and access them via a Switch-Case block? Thank you again in advance.

  Read the article

• Reading Source Code Aloud

  - by Jon Purdy

  After seeing this question, I got to thinking about the various challenges that blind programmers face, and how some of them are applicable even to sighted programmers. Particularly, the problem of reading source code aloud gives me pause. I have been programming for most of my life, and I frequently tutor fellow students in programming, most often in C++ or Java. It is uniquely aggravating to try to verbally convey the essential syntax of a C++ expression. The speaker must give either an idiomatic translation into English, or a full specification of the code in verbal longhand, using explicit yet slow terms such as "opening parenthesis", "bitwise and", et cetera. Neither of these solutions is optimal. On the one hand, an idiomatic translation is only useful to a programmer who can de-translate back into the relevant programming code—which is not usually the case when tutoring a student. In turn, education (or simply getting someone up to speed on a project) is the most common situation in which source is read aloud, and there is a very small margin for error. On the other hand, a literal specification is aggravatingly slow. It takes far far longer to say "pound, include, left angle bracket, iostream, right angle bracket, newline" than it does to simply type #include <iostream>. Indeed, most experienced C++ programmers would read this merely as "include iostream", but again, inexperienced programmers abound and literal specifications are sometimes necessary. So I've had an idea for a potential solution to this problem. In C++, there is a finite set of keywords—63—and operators—54, discounting named operators and treating compound assignment operators and prefix versus postfix auto-increment and decrement as distinct. There are just a few types of literal, a similar number of grouping symbols, and the semicolon. Unless I'm utterly mistaken, that's about it. So would it not then be feasible to simply ascribe a concise, unique pronunciation to each of these distinct concepts (including one for whitespace, where it is required) and go from there? Programming languages are far more regular than natural languages, so the pronunciation could be standardised. Speakers of any language would be able to verbally convey C++ code, and due to the regularity and fixity of the language, speech-to-text software could be optimised to accept C++ speech with a high degree of accuracy. So my question is twofold: first, is my solution feasible; and second, does anyone else have other potential solutions? I intend to take suggestions from here and use them to produce a formal paper with an example implementation of my solution.

  Read the article

• Referencing both an old version and new version of the same DLL (VB.Net)

  - by ckittel

  Consider the following situation: WidgetCompany produced a .NET DLL in 2006 called Widget.dll, version 1.0. I consumed this Widget.dll file throughout my VB.Net application. Over time, WidgetCompany has been updating Widget.dll, I never bothered to keep up, continuing to ship version 1.0 of Widget.dll with my software. It's now 2010, my project is now a VB.Net 3.5 application and WidgetCompany has come out with Widget.dll version 3.0. It looks and functions almost identical to Widget.dll version 1.0, using all the same namespaces and type names from before. However, Widget.dll version 3.0 has many run-time breaking changes since 1.0 and I cannot simply cut over to the new version; however, I don't want to continue developing against the 1.0 version and therefore keep digging myself deeper in the hole. What I want to do is do all new development in my project with Widget.dll version 3.0, whilst keeping Widget.dll version 1.0 around until I find time to convert all of my 1.0 consumption to the newer 3.0 code. Now, for starters, I obviously cannot simply reference both Widget.dll (Ver 1.0) and Widget.dll (Ver 3.0) in Visual Studio. Doing so gives me the following message: "A reference to 'Widget.dll' could not be added. A reference to the component 'Widget' already exists in the project." To work around that, I can simply rename version 3.0 Widget.dll to Widget.3.dll. But this is where I'm stuck. Any attempts to reference types found in "the dll" leads to ambiguity and the compiler obviously doesn't have any clue as to what I really want in this or that case. Is there something I can do that gives a DLL a new "root" Namespace or something? For example, if I could say "Widget.dll has a new root namespace of Legacy" then I could update existing code to reference the types found in Legacy.<RootNamespace> namespace while all new code could simply reference types from the <RootNamespace> namespace. Pipe dream or reality? Are there other solutions to situations this (besides "don't get in this situation in the first place")?

  Read the article

• Constraint Satisfaction Problem

  - by Carl Smotricz

  I'm struggling my way through Artificial Intelligence: A Modern Approach in order to alleviate my natural stupidity. In trying to solve some of the exercises, I've come up against the "Who Owns the Zebra" problem, Exercise 5.13 in Chapter 5. This has been a topic here on SO but the responses mostly addressed the question "how would you solve this if you had a free choice of problem solving software available?" I accept that Prolog is a very appropriate programming language for this kind of problem, and there are some fine packages available, e.g. in Python as shown by the top-ranked answer and also standalone. Alas, none of this is helping me "tough it out" in a way as outlined by the book. The book appears to suggest building a set of dual or perhaps global constraints, and then implementing some of the algorithms mentioned to find a solution. I'm having a lot of trouble coming up with a set of constraints suitable for modelling the problem. I'm studying this on my own so I don't have access to a professor or TA to get me over the hump - this is where I'm asking for your help. I see little similarity to the examples in the chapter. I was eager to build dual constraints and started out by creating (the logical equivalent of) 25 variables: nationality1, nationality2, nationality3, ... nationality5, pet1, pet2, pet3, ... pet5, drink1 ... drink5 and so on, where the number was indicative of the house's position. This is fine for building the unary constraints, e.g. The Norwegian lives in the first house: nationality1 = { :norway }. But most of the constraints are a combination of two such variables through a common house number, e.g. The Swede has a dog: nationality[n] = { :sweden } AND pet[n] = { :dog } where n can range from 1 to 5, obviously. Or stated another way: nationality1 = { :sweden } AND pet1 = { :dog } XOR nationality2 = { :sweden } AND pet2 = { :dog } XOR nationality3 = { :sweden } AND pet3 = { :dog } XOR nationality4 = { :sweden } AND pet4 = { :dog } XOR nationality5 = { :sweden } AND pet5 = { :dog } ...which has a decidedly different feel to it than the "list of tuples" advocated by the book: ( X1, X2, X3 = { val1, val2, val3 }, { val4, val5, val6 }, ... ) I'm not looking for a solution per se; I'm looking for a start on how to model this problem in a way that's compatible with the book's approach. Any help appreciated.

  Read the article

• What was "The Next Big Thing" when you were just starting out in programming?

  - by Andrew

  I'm at the beginning of my career and there are lots of things which are being touted as "The Next Big Thing". For example: Dependency Injection (Spring, etc) MVC (Struts, ASP.NET MVC) ORMs (Linq To SQL, Hibernate) Agile Software Development These things have probably been around for some time, but I've only just started out. And don't get me wrong, I think these things are great! So, what was "The Next Big Thing" when you were starting out? When was it? Were people sceptical of it at first? Why? Did you think it would catch on? Did it pan out and become widely accepted/used? If not, why not? EDIT It's been nearly a week since I first posted this question and I can safely say that I did not expect such explosive interest. I asked the question so that I could gain a perspective of what kinds of innovations in programming people thought were most important when they were starting out. At the time of writing this I have read ~95% of all answers. To answer a few questions, the "Next Big Things" I listed are ones that I am currently really excited about and that I had not really been exposed to until I started working. I'm hoping to implement some or all of these in the near future at my current workplace. To many people they are probably old news. In regards to the "is this a real question" debate, I can see that obviously hasn't been settled yet. I feel bad whenever I read a comment saying that these kinds of questions take away from the real meaning of SO. I'm not wholly convinced that it doesn't. On the other hand, I have seen a lot of comments saying what a great question it is. Anyway, I have chosen "The Internet!" as my answer to this question. I don't think (in my very humble opinion, and, it seems many SOers opinions) that many things related to programming can compare. Nowadays every business and their dog has a website which can do anything from simply supplying information to purchasing goods halfway around the world to updating your blog. And of course, all these businesses need people like us. Thanks to everyone for all the great answers!

  Read the article

• List input and output audio devices in Applet

  - by Jhonny Everson

  I am running a signed applet that needs to provide the ability for the user to select the input and output audio devices ( similar to what skype provides). I borrowed the following code from other thread: import javax.sound.sampled.*; public class SoundAudit { public static void main(String[] args) { try { System.out.println("OS: "+System.getProperty("os.name")+" "+ System.getProperty("os.version")+"/"+ System.getProperty("os.arch")+"\nJava: "+ System.getProperty("java.version")+" ("+ System.getProperty("java.vendor")+")\n"); for (Mixer.Info thisMixerInfo : AudioSystem.getMixerInfo()) { System.out.println("Mixer: "+thisMixerInfo.getDescription()+ " ["+thisMixerInfo.getName()+"]"); Mixer thisMixer = AudioSystem.getMixer(thisMixerInfo); for (Line.Info thisLineInfo:thisMixer.getSourceLineInfo()) { if (thisLineInfo.getLineClass().getName().equals( "javax.sound.sampled.Port")) { Line thisLine = thisMixer.getLine(thisLineInfo); thisLine.open(); System.out.println(" Source Port: " +thisLineInfo.toString()); for (Control thisControl : thisLine.getControls()) { System.out.println(AnalyzeControl(thisControl));} thisLine.close();}} for (Line.Info thisLineInfo:thisMixer.getTargetLineInfo()) { if (thisLineInfo.getLineClass().getName().equals( "javax.sound.sampled.Port")) { Line thisLine = thisMixer.getLine(thisLineInfo); thisLine.open(); System.out.println(" Target Port: " +thisLineInfo.toString()); for (Control thisControl : thisLine.getControls()) { System.out.println(AnalyzeControl(thisControl));} thisLine.close();}}} } catch (Exception e) {e.printStackTrace();}} public static String AnalyzeControl(Control thisControl) { String type = thisControl.getType().toString(); if (thisControl instanceof BooleanControl) { return " Control: "+type+" (boolean)"; } if (thisControl instanceof CompoundControl) { System.out.println(" Control: "+type+ " (compound - values below)"); String toReturn = ""; for (Control children: ((CompoundControl)thisControl).getMemberControls()) { toReturn+=" "+AnalyzeControl(children)+"\n";} return toReturn.substring(0, toReturn.length()-1);} if (thisControl instanceof EnumControl) { return " Control:"+type+" (enum: "+thisControl.toString()+")";} if (thisControl instanceof FloatControl) { return " Control: "+type+" (float: from "+ ((FloatControl) thisControl).getMinimum()+" to "+ ((FloatControl) thisControl).getMaximum()+")";} return " Control: unknown type";} } But what I get: Mixer: Software mixer and synthesizer [Java Sound Audio Engine] Mixer: No details available [Microphone (Pink Front)] I was expecting the get the real list of my devices (My preferences panels shows 3 output devices and 1 Microphone). I am running on Mac OS X 10.6.7. Is there other way to get that info from Java?

  Read the article

• PL/SQL pre-compile and Code Quality checks in an automatted build environment?

  - by Lars Corneliussen

  We build software using Hudson and Maven. We have C#, java and last, but not least PL/SQL sources (sprocs, packages, DDL, crud) For C# and Java we do unit tests and code analysis, but we don't really know the health of our PL/SQL sources before we actually publish them to the target database. Requirements There are a couple of things we wan't to test in the following priority: Are the sources valid, hence "compilable"? For packages, with respect to a certain database, would they compile? Code Quality: Do we have code flaws like duplicates, too complex methods or other violations to a defined set of rules? Also, the tool must run head-less (commandline, ant, ...) we wan't to do analysis on a partial code base (changed sources only) Tools We did a little research and found the following tools that could potencially help: Cast Application Intelligence Platform (AIP): Seems to be a server that grasps information about "anything". Couldn't find a console version that would export in readable format. Toad for Oracle: The Professional version is said to include something called Xpert validates a set of rules against a code base. Sonar + PL/SQL-Plugin: Uses Toad for Oracle to display code-health the sonar-way. This is for browsing the current state of the code base. Semantic Designs DMSToolkit: Quite general analysis of source code base. Commandline available? Semantic Designs Clones Detector: Detects clones. But also via command line? Fortify Source Code Analyzer: Seems to be focussed on security issues. But maybe it is extensible? more... So far, Toad for Oracle together with Sonar seems to be an elegant solution. But may be we are missing something here? Any ideas? Other products? Experiences? Related Questions on SO: http://stackoverflow.com/questions/531430/any-static-code-analysis-tools-for-stored-procedures http://stackoverflow.com/questions/839707/any-code-quality-tool-for-pl-sql http://stackoverflow.com/questions/956104/is-there-a-static-analysis-tool-for-python-ruby-sql-cobol-perl-and-pl-sql

  Read the article

• More GCC link time issues: undefined reference to main

  - by vikramtheone

  Hi Guys, I'm writing software for a Cortex-A8 processor and I have to write some ARM assembly code to access specific registers. I'm making use of the gnu compilers and related tool chains, these tools are installed on the processor board(Freescale i.MX515) with Ubuntu. I make a connection to it from my host PC(Windows) using WinSCP and the PuTTY terminal. As usual I started with a simple C project having main.c and functions.s. I compile the main.c using GCC, assemble the functions.s using as and link the generated object files using once again GCC, but I get strange errors during this process. An important finding - Meanwhile, I found out that my assembly code may have some issues because when I individually assemble it using the command as -o functions.o functions.s and try running the generated functions.o using ./functions.o command, the bash shell is failing to recognize this file as an executable(on pressing tab functions.o is not getting selected/PuTTY is not highlighting the file). Can anyone suggest whats happening here? Are there any specific options I have to send, to GCC during the linking process? The errors I see are strange and beyond my understanding, I don't understand to what the GCC is referring. I'm pasting here the contents of main.c, functions.s, the Makefile and the list of errors. Help, please!!! Vikram main.c #include <stdio.h> #include <stdlib.h> int main(void) { puts("!!!Hello World!!!"); /* prints !!!Hello World!!! */ return EXIT_SUCCESS; } functions.s * Main program */ .equ STACK_TOP, 0x20000800 .text .global _start .syntax unified _start: .word STACK_TOP, start .type start, function start: movs r0, #10 movs r1, #0 .end Makefile all: hello hello: main.o functions.o gcc -o main.o functions.o main.o: main.c gcc -c -mcpu=cortex-a8 main.c functions.o: functions.s as -mcpu=cortex-a8 -o functions.o functions.s Errors ubuntu@ubuntu-desktop:~/Documents/Project/Others/helloworld$ make gcc -c -mcpu=cortex-a8 main.c as -mcpu=cortex-a8 -o functions.o functions.s gcc -o main.o functions.o functions.o: In function `_start': (.text+0x0): multiple definition of `_start' /usr/lib/gcc/arm-linux-gnueabi/4.3.3/../../../crt1.o:init.c:(.text+0x0): first defined here /usr/lib/gcc/arm-linux-gnueabi/4.3.3/../../../crt1.o: In function `_start': init.c:(.text+0x30): undefined reference to `main' collect2: ld returned 1 exit status make: *** [hello] Error 1

  Read the article

• Agilent E4426B signal generator locks up during multiple GPIB *SAV operations

  - by aspiehler

  I have a test fixture with an Agilent E4426B RF signal generator connected to a PC via a National Instrument Ethernet-to-GPIB bridge. My software is attempting to sanitize the instrument by presetting it and then saving the current state to all of the memory locations writable via the standard SCPI command "*SAV x,y". The loop works to a point, but eventually the instrument responds with an error and continuously displays the "L" icon on the front display and a "Remote preset" message at the bottom. At that point it won't respond to any more remote commands and I have to either cycle power or press LOCAL, then PRESET at which point it takes about 3 minutes to finish presetting. At that point the "L" icon is still present and and the next GPIB command sent to the instrument causes it to report a -113 error (undefined header) in the instrument error queue. I fired up NI spy to see what was happening, and found that the error was happening at the same point in the loop - "*SAV 6,2" in this case. From NI Spy: Send (0, 0x0017, "*SAV 6,2", 8 (0x8), NLend (0,0x01)) Process ID: 0x00000520 Thread ID: 0x00000518 ibsta:0xc168 iberr: 6 ibcntl: 2(0x2) And here's the code from the instrument driver: int CHP_E4426b::Erase() { if ((m_StatusCode = Initialize()) != GPIB_SUCCESS) // basically just sends "*RST" return m_StatusCode; m_SaveState = "*SAV %d, %d"; for (int i=0; i < 10; i++) for (int j=0; j < 100; j++) { sprintf(m_CmdString, m_SaveState, j, i); if ((m_StatusCode = Send(m_CmdString, strlen(m_CmdString))) != GPIB_SUCCESS) return m_StatusCode; } return GPIB_SUCCESS; } I tried putting a small Sleep() delay (10-20 ms) at the end of the inner loop, and to my surprise it caused the error to show up earlier rather than later. 10 ms caused the loop to error out at 44,1 and 20 ms was even sooner. I've already eliminated faulty cabling or the instrument as the culprit. This same type of sequence works without any error on a higher end signal generator, so I'm tempted to chalk this up to a bug in the instrument's firmware.

  Read the article

• mysql_connect() causes page to not display (WAMP)

  - by VOIDHand

  I currently have a website running MySQL and PHP in which this is all working. I've tried installing WAMPServer to be able to work on the site on my own computer, but I have been having issues trying to get the site to work correctly. HTML and PHP files work correctly (by going to http://localhost/index.php, etc.). But some of the pages display "This Webpage is not available" (in Chrome) or "Internet Explorer cannot display this webpage", which leads me to think there is an error is the server, as when the page doesn't exist, it typically dispays "Oops! This link appears to be broken" or IE's standard 404 page. Each page in my site has an include() call to set up an instance of a class to handle all database transactions. This class opens the connection to the database in its constructor. I have found commenting out the contents of the constructor will allow the page to load, although this understandably causes errors later in the page. This is the contents of the included file: class dbAccess { private $db; function __construct() { $this->db = mysql_connect("externalURL","user","password") or die ("Connection for database not found."); mysql_select_db("dbName", $this->db) or die ("Database not selected"); } ... } As a note for what's happening here. I'm attempting to use the database on my site, rather than the local machine. The actual values of externalURL, dbName, user, and password work when I plug them into my database software and the file fine of the site, so I don't think the issue is with those values themselves, but rather some setting with Apache or Wamp. The issue persists if I try a local database as well. This is an excerpt of my Apache error log for one attempt at logging into the site: [Wed Apr 14 15:32:54 2010] [notice] Parent: child process exited with status 255 -- Restarting. [Wed Apr 14 15:32:54 2010] [notice] Apache/2.2.11 (Win32) PHP/5.3.0 configured -- resuming normal operations [Wed Apr 14 15:32:54 2010] [notice] Server built: Dec 10 2008 00:10:06 [Wed Apr 14 15:32:54 2010] [notice] Parent: Created child process 1756 [Wed Apr 14 15:32:55 2010] [notice] Child 1756: Child process is running [Wed Apr 14 15:32:55 2010] [notice] Child 1756: Acquired the start mutex. [Wed Apr 14 15:32:55 2010] [notice] Child 1756: Starting 64 worker threads. [Wed Apr 14 15:32:55 2010] [notice] Child 1756: Starting thread to listen on port 80. For the first line, isLoggedIn (from the first line) is a method of the class above. Assuming that the connection works, this error should disappear. I've tried searching for solutions online, but haven't been able to find anything to help. If you need any further information to help solve this issue, feel free to ask for it. (One more note, I don't even have Skype on this computer, so I can't see it being an issue, as this conflict seems to be the default response for any Wamp issue.) [Edit: Removed entry from the error log as it was solved as an unrelated issue]

  Read the article

• Should I deal with files longer than MAX_PATH?

  - by John

  Just had an interesting case. My software reported back a failure caused by a path being longer than MAX_PATH. The path was just a plain old document in My Documents, e.g.: C:\Documents and Settings\Bill\Some Stupid FOlder Name\A really ridiculously long file thats really very very very..........very long.pdf Total length 269 characters (MAX_PATH==260). The user wasn't using a external hard drive or anything like that. This was a file on an Windows managed drive. So my question is this. Should I care? I'm not saying can I deal with the long paths, I'm asking should I. Yes I'm aware of the "\?\" unicode hack on some Win32 APIs, but it seems this hack is not without risk (as it's changing the behaviour of the way the APIs parse paths) and also isn't supported by all APIs . So anyway, let me just state my position/assertions: First presumably the only way the user was able to break this limit is if the app she used uses the special Unicode hack. It's a PDF file, so maybe the PDF tool she used uses this hack. I tried to reproduce this (by using the unicode hack) and experimented. What I found was that although the file appears in Explorer, I can do nothing with it. I can't open it, I can't choose "Properties" (Windows 7). Other common apps can't open the file (e.g. IE, Firefox, Notepad). Explorer will also not let me create files/dirs which are too long - it just refuses. Ditto for command line tool cmd.exe. So basically, one could look at it this way: a rouge tool has allowed the user to create a file which is not accessible by a lot of Windows (e.g. Explorer). I could take the view that I shouldn't have to deal with this. (As an aside, this isn't an vote of approval for a short max path length: I think 260 chars is a joke, I'm just saying that if Windows shell and some APIs can't handle 260 then why should I?). So, is this a fair view? Should I say "Not my problem"? Thanks! John

  Read the article

• Is it too early to start designing for Task Parallel Library?

  - by Joe Erickson

  I have been following the development of the .NET Task Parallel Library (TPL) with great interest since Microsoft first announced it. There is no doubt in my mind that we will eventually take advantage of TPL. What I am questioning is whether it makes sense to start taking advantage of TPL when Visual Studio 2010 and .NET 4.0 are released, or whether it makes sense to wait a while longer. Why Start Now? The .NET 4.0 Task Parallel Library appears to be well designed and some relatively simple tests demonstrate that it works well on today's multi-core CPUs. I have been very interested in the potential advantages of using multiple lightweight threads to speed up our software since buying my first quad processor Dell Poweredge 6400 about seven years ago. Experiments at that time indicated that it was not worth the effort, which I attributed largely to the overhead of moving data between each CPU's cache (there was no shared cache back then) and RAM. Competitive advantage - some of our customers can never get enough performance and there is no doubt that we can build a faster product using TPL today. It sounds fun. Yes, I realize that some developers would rather poke themselves in the eye with a sharp stick, but we really enjoy maximizing performance. Why Wait? Are today's Intel Nehalem CPUs representative of where we are going as multi-core support matures? You can purchase a Nehalem CPU with 4 cores which share a single level 3 cache today, and most likely a 6 core CPU sharing a single level 3 cache by the time Visual Studio 2010 / .NET 4.0 are released. Obviously, the number of cores will go up over time, but what about the architecture? As the number of cores goes up, will they still share a cache? One issue with Nehalem is the fact that, even though there is a very fast interconnect between the cores, they have non-uniform memory access (NUMA) which can lead to lower performance and less predictable results. Will future multi-core architectures be able to do away with NUMA? Similarly, will the .NET Task Parallel Library change as it matures, requiring modifications to code to fully take advantage of it? Limitations Our core engine is 100% C# and has to run without full trust, so we are limited to using .NET APIs.

  Read the article

• Observer pattern used with decorator pattern

  - by icelated

  I want to make a program that does an order entry system for beverages. ( i will probably do description, cost) I want to use the Decorator pattern and the observer pattern. I made a UML drawing and saved it as a pic for easy viewing. This site wont let me upload as a word doc so i have to upload a pic - i hope its easily viewable.... I need to know if i am doing the UML / design patterns correctly before moving on to the coding part. Beverage is my abstract component class. Espresso, houseblend, darkroast are my concrete subject classes.. I also have a condiment decorator class milk,mocha,soy,whip. would be my observer? because they would be interested in data changes to cost? Now, would the espresso,houseblend etc, be my SUBJECT and the condiments be my observer? My theory is that Cost is a changes and that the condiments need to know the changes? So, subject = esspresso,houseblend,darkroast,etc.. // they hold cost() Observer = milk,mocha,soy,whip? // they hold cost() would be the concrete components and the milk,mocha,soy,whip? would be the decorator! So, following good software engineering practices "design to an interface and not implementation" or "identify things that change from those that dont" would i need a costbehavior interface? If you look at the UML you will see where i am going with this and see if i am implementing observer + Decorator pattern correctly? I think the decorator is correct. since, the pic is not very viewable i will detail the classes here: Beverage class(register observer, remove observer, notify observer, description) these classes are the concrete beverage classes espresso, houseblend,darkroast, decaf(cost,getdescription,setcost,costchanged) interface observer class(update) // cost? interface costbehavior class(cost) // since this changes? condiment decorator class( getdescription) concrete classes that are linked to the 2 interface s and decorator are: milk,mocha,soy,whip(cost,getdescription,update) these are my decorator/ wrapper classes. Thank you.. Is there a way to make this picture bigger?

  Read the article

• What Can I Do To One Of My Team Number (Good Friend As Well) Who Lost His Passion.

  - by skyflyer

  It seems this question is not program related, but there are lot of similar questions. So please bear with me! By the way, I am programmer and my team is also charging a software project. And SO is the only place which solved me lot of thorny troubles!THANK YOU GUYS! I joined my company with him years ago. At that time he was quite passionate on his job which is a front-end development. He gave us lot of useful suggestions concerning his work like design. And I believed he was a smart guy. I believe he still is smart too by the way. One years later, however, he seemed lost his passion and fooling around every day, did not care about his work any more and produced poorwork. Even worse he literally stopped learning new skills and honing his work related skills. For me it is horrible, we got to keep abreast with new technology development, otherwise we will be throw out. Since we were just coworkers, I did not care about it too much except mentioned my thoughts several times. But last month, we resembled a new group and assigned very important project. And I am the team leader, sadly! My boss gave me lot of support and expectation as well. I did a pretty good job before and I am very optimism to our future. But as a team, if my team does not work hard, we will be doomed to failure no matter how hard I work and push. In order to revitalize his passion, I tried couple of ways like talking to him about my concern and my boss's angry. I offered his new task which is quite new to him. I even persuaded my boss to give him new incentive package. But all of them knocked wall. His reaction was just he did not care. Even worse he did not want to talk about his situation. I want to be hard on him, but since we are friends and coworkers, I really can not see it will work. Even it works, I can not so quickly change my self from friend and coworker into manager. As a novice in management, I am really overwhelmed! I do not want get him fired, we are friends and I do not see him fired as my team number. What can I do? Thank you guys!

  Read the article

• Workflow for statistical analysis and report writing

  - by ws

  Does anyone have any wisdom on workflows for data analysis related to custom report writing? The use-case is basically this: Client commissions a report that uses data analysis, e.g. a population estimate and related maps for a water district. The analyst downloads some data, munges the data and saves the result (e.g. adding a column for population per unit, or subsetting the data based on district boundaries). The analyst analyzes the data created in (2), gets close to her goal, but sees that needs more data and so goes back to (1). Rinse repeat until the tables and graphics meet QA/QC and satisfy the client. Write report incorporating tables and graphics. Next year, the happy client comes back and wants an update. This should be as simple as updating the upstream data by a new download (e.g. get the building permits from the last year), and pressing a "RECALCULATE" button, unless specifications change. At the moment, I just start a directory and ad-hoc it the best I can. I would like a more systematic approach, so I am hoping someone has figured this out... I use a mix of spreadsheets, SQL, ARCGIS, R, and Unix tools. Thanks! PS: Below is a basic Makefile that checks for dependencies on various intermediate datasets (w/ ".RData" suffix) and scripts (".R" suffix). Make uses timestamps to check dependencies, so if you 'touch ss07por.csv', it will see that this file is newer than all the files / targets that depend on it, and execute the given scripts in order to update them accordingly. This is still a work in progress, including a step for putting into SQL database, and a step for a templating language like sweave. Note that Make relies on tabs in its syntax, so read the manual before cutting and pasting. Enjoy and give feedback! http://www.gnu.org/software/make/manual/html%5Fnode/index.html#Top R=/home/wsprague/R-2.9.2/bin/R persondata.RData : ImportData.R ../../DATA/ss07por.csv Functions.R $R --slave -f ImportData.R persondata.Munged.RData : MungeData.R persondata.RData Functions.R $R --slave -f MungeData.R report.txt: TabulateAndGraph.R persondata.Munged.RData Functions.R $R --slave -f TabulateAndGraph.R report.txt

  Read the article

< Previous Page | 761 762 763 764 765 766 767 768 769 770 771 772  | Next Page >