Search Results

Search found 12844 results on 514 pages for 'dual graphics card'.

Page 77/514 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

  • What Wireless Router/ADSL Modem to get? N-band a must!!

    - by JJarava
    I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

    Read the article

  • Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

    - by cpm
    I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

    Read the article

  • Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

    - by cpm
    I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

    Read the article

  • trying to format a sd card

    - by masfenix
    I recently found a SD card (1gb) lying around. Thought i might pop that into my card reader and see if anything is on it. nothing.. there isnt even a file system on it. so i try to right click and go "format" but nothing happens. so i try in command. i launch cmd and i go format f: it gave the following back:

    Read the article

  • BSOD - probably video card prob

    - by Shimmy
    I'm receiving the following BSOD: I've tried installing the latest driver from nVidia (296.10), but it says "NVIDIA installer cannot continue", "The graphics driver could not find compatible graphics hardware.": I installed it manually at device manager, but problem still occurs. The problem does not happen in safe mode at all. Note: After restarting the computer when seeing this BSOD, the BIOS welcome screen is full of random black dots spread around: Any solutions? Update: I've tried disabling Aero by following this guide, but that didn't help.

    Read the article

  • Trying to format an SD card.

    - by masfenix
    I recently found a SD card (1gb) lying around. Thought I might pop that into my card reader and see if anything is on it. Nothing. There isn't even a file system on it. So I try to right click and go "format" but nothing happens. So I try in command. I launch cmd and I go format f: This is the result:

    Read the article

  • IBM x260m won't boot from PCI raid card

    - by syrenity
    Hi. We ghosted our old Windows 2003 drive to a new 1TB one, and connected through new PCI SATA card. The server fails to boot with error 1962: Boot sector not found. When we connect the drive directly to motherboard, it boots fine, so the problem is probably in getting BIOS boot from the SATA card. Does anyone know how to do it? Thanks.

    Read the article

  • rfkill unblock all does not activate a certain wireless card

    - by Davidos
    With an intel 1000 wireless card; rfkill list 0: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: tpacpi_bluetooth_sw: Bluetooth Soft blocked: yes Hard blocked: no rfkill unblock all 0: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no Why does my wireless card not turn on?

    Read the article

  • DBRD dual primary Heartbeat resource management

    - by Jon Skarpeteig
    I have the following setup: Two servers with DRBD running dual primary with OCFS2 Heartbeat with two virtual ips, one for each server Round robin DNS to load balance NFS across the two vIPs Shutting down Server1 for a period of time, cause Server2 to take over the vIP for failover. However, when Server1 returns - it takes over the designated vIP as soon as heartbeat gets connection again - even though the DRBD is running sync (and thus not up to date) How can I configure heartbeat to perform failback as soon as Server1 again is in sync with Server2 ? (And not before)

    Read the article

  • Dual Monitors for Windows 8

    - by antonio081014
    I have one monitor and a projector connecting to my computer, while the screen keep flashing after every 10 seconds, it seems the resolution keeps changing. The project is the a dual display for the monitor. They displays the same content. My current resolution is 1024*768, while after 10 seconds around, the resolution goes to something big, then after a few seconds, it goes back to 1024*768. I wonder if this is a problem about the resolution, or it's about the compatible of screen display?

    Read the article

  • IEEE 1394 Firewire Card is not visible in Device Manager in WIndows 7

    - by Shyam
    I have a IEEE 1394 card that I have placed in one of the PCI slots of my Windows 7 PC. I have moved to Windows just last week and Windows is not detecting this card. It is not listed in the Devide Manager. Earlier when I used Fedora 12, I was able to use this interface for capturing videos from my DV Camera. The manufacturer is Tech-Com, which has not provided a driver CD for this. What can I possibly try?

    Read the article

  • Best dual band A/B/G/N wireless router/ap for Linux

    - by Kevin Bowling
    Hello, I am looking for the best A/B/G/N dual band (simultaneous) router or access point that can be flashed with community firmware like dd-wrt or openwrt. In the past I have used the WRT54G series from Linksys with great success as access points and bridges. The WRT610N looks nice but I'm not sure how well the community firmwares support it. I am open to any manufacturer and any input or experience would be appreciated.

    Read the article

  • Setting up a WPA-PSK network card to connect to a WPA2 network

    - by mattshepherd
    I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

    Read the article

  • Is there a difference between the actual chip intended for Dual Channel vs Triple Channel

    - by JimDel
    Is there a difference between the actual chips intended for Dual Channel vs Triple Channel. I bought a set of triple channel memory but I'm only using 2 of the 3 chips. I'm getting the error "Display driver NVIDIA Windows Kernel Mode Driver, Version 197.45 stopped responding and has successfully recovered" There seems to be a TON of discussion on the web about this and some say it might be RAM related. This is the ram I'm using. Thanks

    Read the article

  • Is Hacom Mars II Dual Blade good ?

    - by Joachim H. Skeie
    I am considering getting a Hacom Mars II Dual Blade for use as a firewall in a data-center for one of my colocated solutions. As the 1U enclosure have two identical firewalls, I am intending to use one of the firewalls as the external firewall using packet-filtering and load balancer (balancing load for my front-end nodes), while using the second as the internal firewall (as an application gateway). But I have no experience with Hacom, or pfSense firewalls. They do look really good on paper, but how are they in practice ?

    Read the article

  • Setting up dual NICs under Server 2008

    - by Randall Sexton
    Hi, I'm trying to determine how to set up dual NICs on my Server 2008 box (not R2). I want all web traffic on one NIC and all Hyper-V traffic on the other. Is this possible? ( I assume that it is ) How is this done? ( A link to a tutorial you know of would be great ) Both NICs are the same (Intel PRO/1000 EB Network Connection with I/O Acceleration). Thanks in advance, Randall

    Read the article

  • Re. copying movie from USB card reader back to my camera

    - by Alice P
    I have a Canon Digital Ixus 860IS. I originally copied a short movie from my camera onto the computer via a USB card reader and then copied it back onto the camera via the same USB card reader along with some photos. The photos have copied back fine but the movie, although it's showing to have copied, can't be seen. Any reason for this? Thanks

    Read the article

  • Dual external internet connections

    - by cpf
    Hi ServerFault, We have here 2 Internet connections coming in. And the intention is to have all services available on our server which should be available externally, to be available through both connections. Also, one connection should be used as few as possible, except for certain protocols. How can I achieve this dual connection method?

    Read the article

  • Mac Pro Boot Camp w/ RAID card

    - by churnd
    If I configure a Mac Pro with a RAID card and two 15k RPM drives, and leave the drives JBOD (no RAID configured), can I install Windows on the second drive? I guess the question really is, does Windows recognize the RAID card? I know it's probably just a rebadged LSI or Adaptec but wanted to see if anyone's actually done it...

    Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >