Search Results

Search found 4186 results on 168 pages for 'ember router'.

Page 77/168 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

  • bridge network using route

    - by wannabe
    I have been googeling and searching on how to do bridge my wifi connections to my internet connection using route. I have a ubuntu server 12.04 with a wifi and normal network card I also have a router that is connected to the internet on my ubuntu server i have eth0 connected to the router; IP 192.168.1.12 GW 192.168.1.1 DNS 212.54.40.25 this all works great I have set up my wlan0 as my accespoint, and DHCP to feed an IP to any device that connects to it. if i connect, for example, my android smartphone to my wlan0 acces point it will get the following IP 10.10.0.2 GW 10.10.0.1 DNS 212.54.40.25 How in earth can I bridge this connection and acces the internet from my android? I dont want to make use of BR0 bridge-utils but accomplish this using route. Many thanks in advance

    Read the article

  • access to site owner not working

    - by Daveo
    I made a website it works for everyone except for the site owner, who cannot access the site. He gets a server could not be found error. I went to his house and the issue occurs for all of his devices (PC, laptop, iPhone using WiFi) when I turn WiFi off the iPhone it works. So I thought it was a problem on his router so I reset is router to default factory settings but it still does not work, I have flushed his DNS cache and his browser cache. But nothing seems to help. He cannot even PING the server using the domain name. However when he uses the IP address he can see the site fine. I looked in cpanel for an blocked IP addresses but cannot see anything. What could be stopping just him from accessing the site via domainname and not the IP address? Site details are: PHP, osCommerce it is hosted by site5 on my reseller account.

    Read the article

  • WiFi, No ping, other works fine

    - by Linux Mom
    I installed Ubuntu 12.04 LTS for my mom, this runs OK. However recently, I switched back and forth between encryptions on our WiFi Router from WPA-PSK to WEP and back again to WPA-PSK, same password. Now this old laptop won't even ping the gateway on the router, although the nm-applet shows connected. I tried re-adding the network and putting in the BSSID. I did this over again sometimes just to verify. I tried with my 3G Tethering on my phone, it works fine, can go online too. My other Linux laptop can go on the same wifi as well as my phone. And this laptop used to been online on the same network, same password, same encryption (WPA-PSK) What can be wrong ? Does it need a serious kick in the butt or removing some cached authorisation somewhere?

    Read the article

  • Internet connection crashes while wifi / lan stay connected

    - by pirad
    I am connected to a router by wifi or lan. But every few moments (sometimes seconds, sometimes half an hour) my connection to the internet breaks down. So in one moment I can surf with my firefox and have ping times of 20 ms (wifi) to the google server. And in the next moment I can't open any pages in any browser and the ping shows no new messages first and then "Destination Host Unreachable". This is especially odd as another computer or my smart phone stays connected at the same time to the same network and seems to notice nothing. So I have a problem independend of wifi or lan drivers but with something else. Where should I look for logs that could tell me more information? I can't find some in syslog. Just if I reconnect to the router (wich works for another few moments) there are a lot of informations. But everythin is okay then.

    Read the article

  • JS framework with conditionally loaded fragments

    - by kjs3
    I'm doing a single-page, responsive, mobile first design. I found this article about conditionally loaded fragments but am wondering what the different js frameworks have build-in to handle this? I'm imagining the mobile version with a list view fragment that transitions to a show view fragment. A larger portal could just show both fragments and change the show fragment when items in the list are clicked. I'd love thoughts on what is available from the various frameworks, not an argument. Ember?, Angular?, etc. Maybe I'm missing it, but I'm not seeing the responsive fragments issue brought up in the various demos I've found so far.

    Read the article

  • Wifi very slow on Ubuntu 12.04 but not on Win7, need help

    - by user84504
    I have an enormous problem: I've a Sony Vaio VGN-NR21S with win7 and Ubuntu 12.04 in dual boot. With Windows everything is fine (except that is windows) but with Ubuntu the wireless connection is awfully slow, basically unusable. I've already search for similar discussion but the solution proposed didn't worked. I've noticed this issue also in live mode both with ubuntu and linux mint. I've installed Ubuntu onto an Acer that shows the same problem when connected via wifi to my router, so I think that maybe the issue is about compatibility with my home router. I really need help, I don't want unistall ubuntu! Please tell me which output u need to help me, thanks.

    Read the article

  • How can I reconnect to a ssh session after a broken pipe?

    - by Chauncellor
    So I was running apt-get upgrade on a server when the router decided it had been too long since it last made me angry: It dropped all connection. Moral of the story is to use screen a lot when you're on a bum router. Anyway, I logged back in and found in htop that the process was still hanging there, still waiting for my Y/n to upgrade (hadn't hit it yet, luckily). Is there any way I can reattach to a session that had been broken off? I ended up just killing it since it wasn't in the middle of package management but it would be great to know for future reference.

    Read the article

  • Internet (HTTP) is not working on Sony Viao

    - by vijay
    I switched my sony viao laptop from XP to ubuntu 10.04 recently. I have it connected through router at home. The internet was working fine with XP. With ubuntu, i am not able to connect to interenet. I am able to update using apt, and i am able to ping too. It seems like there is a DNS issue, when i try to goto sites from firefox, it doesn't work. I tried disabling the ipv6 in firefox config, it doesn't work. My router is on 192.168.2.1 instead of 192.168.1.1 any ideas on what config i might need to change to make this work? or could this be a drive issue?

    Read the article

  • How do I secure a Tomcat installation?

    - by spangeman
    I have installed tomcat on my Ubuntu Home 11.10 system and can successfully access the test page online after port forwarding on 8080 within my router. I have not made any other changes to the router, Ubuntu or the tomcat install, everything else has remained standard. I intend on using this to play around with Java Servlets and basic web development for my own personal use. What steps, if any, would you suggest I take to ensure this is secure? Should I change anything within the Tomcat configuration? This seemed like a good idea to limit access - http://www.seankilleen.com/2010/09/how-to-allow-only-specific-ip-addresses_30.html But I am open to any other recommendations.

    Read the article

  • How to debug wifi connection?

    - by mmb
    I am using Ubuntu's Network Manager to connect to a local wifi router. My problem is, that it often disconnects without any visible reason (router is on, internet connection seems to be working, wifi diodes are blinking). I mostly have to disable wifi from Network Manager, enable it again to get wifi connecting again. Plus I am often experiencing Network Manager trying to connect to my wifi, trying several times but then giving up. I even tried an external usb-wifi card, but with the very same results. My question is: How can I debug this? Which logs should I read to see what is really happening when all of these errors occur - so I can post them here and see how to proceed?

    Read the article

  • Modern website/webapp setup

    - by onepiece
    I'm new to web development. From looking at popular open-source frameworks for both front-end and back-end, I have a general idea of what the modern full-stack web setup looks like: Database <- Back-end language ~ REST API <- Front-end Notes: The back-end language (Python, Ruby, PHP, Java) generates the API, which is the only layer between the back and the front. The API will have authentication to protect private data. The front-end sends GET and POST requests to the API. A MVC framework can be used, such as Backbone, Angular, or Ember.js. Does this align with best practices for web development?

    Read the article

  • Wi-Fi not working only on Ubuntu computer?

    - by Joseph_carp
    The Wi-Fi at our house does not work on my Asus notebook running Ubuntu 12.04. It works fine on all other devices except this one. Internet worked fine before I had Ubuntu and I had Windows 7, but we also had a different ISP and place. My roommate's Windows 7 notebook and netbook both work fine with the internet and so do all of our phones and iPods. I do not know what is wrong because it works fine EVERYWHERE else, but when I am connected to my own router at my house it is either EXTREMELY slow or it just loads and loads and loads. I have all of the correct drivers and all that so why is it just this one connection that is a problem. I do not know if this matters but the ISP is Comcast and so is the Modem/wireless-router. Any help is much appreciated, thank you.

    Read the article

  • My ethernet connection is not working but it is detected by my computer

    - by smithy545
    I'm setting up an old computer with ubuntu server 12.04. I wiped the drive and went through the installation fine but afterwards the ethernet would not work. It's physically connected to the router and the card is recognized by lspci(SiS 900) but it won't connect at all. I've plugged in and installed the drivers for a wifi adapter and it's worked with the same router. Just so you know I've turned it on and off plenty of times. Any help would be appreciated.

    Read the article

  • Ubuntu 12.04 wifi problem

    - by Akaash
    I'm having trouble with wifi on my MSI U180 netbook using Ubuntu 12.04. When I boot up the netbook, it will connect to my router however after a few minutes the wifi will just stop working and not find or connect to any networks. The only way to get wifi connectivity back is to reboot the netbook however the connection will again only last a few minutes. A wired connection works fine. I have tried connecting to a different router and the same thing happens. My friend has the same OS and netbook and his works fine. Does anybody have any possible solutions? Thanks in advance.

    Read the article

  • Windows 7 intermittently drops wired internet/lan connection.

    - by CraigTP
    In a nutshell, my Windows 7 Ultimate PC intermittently drops it's internet connection. Why? Background: My PC is wired to my ADSL modem/router which is directly connected to the phone line. I also have wireless connectivity turned on within the router for a laptop to connect wirelessly. Every few hours or so, when using my PC, I find I cannot access the internet and pages will not load. Eventually, Windows7 will update the network icon in the task-tray to show the exclamation mark symbol on the network icon. Opening up the Network And Sharing Centre will show the red cross between the "Multiple Networks" and "The Internet". Here's a picture of the "Network And Sharing Centre" (grabbed when everything was working!) As you can see, I'm running Sun's VirtualBox on this machine and that creates a Network connection for itself. This doesn't seem to affect the intermittent dropping (i.e. the intermittent drops occur whether the VirtualBox connection is in use or not). When the connection does drop, I cannot access any internet pages, nor can I access the router's web admin page at http://192.168.1.1/, so I'm assuming I've lost all local LAN access too. It's definitely not the router (or the internet connection itself) as my laptop, using the wireless connection (and running Vista Home Premium) continues to be able to access the internet (and the router's web admin pages) just fine. Every time this happens, I can immediately restore all internet and LAN access by opening Network Adapter page, disabling the "Local Area Connection" and then re-enabling it. Give it a few seconds and everything is fine again. I assume this is because, beneath the GUI, it's effectively doing an "ipconfig /release" then "ipconfig /renew". Why does this happen in the first place, though? I've googled for this and seen quite a few other people (even on MSDN/Technet forums) experiencing the same or almost the same problem, but with no clear resolution. Suggestions of turning off IPv6 on the LAN adapter, and ensuring there's no power management "sleeping" the network adapter have been tried but do not cure the problem. There does not seem to be any particular sequence of events that cause it to happen either. I've had it go twice in 20 minutes when just randomly browsing the web with no other traffic, and I've also had it go once then not go again for 2-3 hours with the same sort of usage. Can anyone tell me why this is happening and how to make it stop? EDIT: Additional information based upon the answer provided so far: Firstly, I forgot the mention that this is Windows 7 64 bit if that makes any difference at all. I mentioned that I don't think the VirtualBox network adpater is causing this problem in any way, and I also have VirtualBox installed on two other machines, one running Vista Home Premium and the other running XP. Neither of these machine experience the same network connectivity issues as the Windows 7 machine. The IP assignment for the Windows 7 machine is the same both before and after the "drop". I have a DHCP server on the router issuing IP Addresses, however my Windows 7 machine uses a static address. Here's the output from "ipconfig": Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Within the system's event logs, the only event that relates to the connection dropping is a "DNS Client Event" and this is generated after the connection has dropped and is an event detailing that DNS information can't be found for whatever website I may be trying to access, just as the connection drops: Log Name: System Source: Microsoft-Windows-DNS-Client Event ID: 1014 Task Category: None Level: Warning Keywords: User: NETWORK SERVICE Description: Name resolution for the name weather.service.msn.com timed out after none of the configured DNS servers responded. The network adapter chipset is Realtek PCIe GBE Family Controller and I have confirmed that this is the correct chipset for the motherboard (Asus M4A77TD PRO), and in fact, Windows Update installed an updated driver for this on 12/Jan/2009. The details of the update say that it's a Realtek software update from December 2009. Incidentally, I was still having the same intermittent problems prior to this update. It seems to have made no difference at all. EDIT 2 (1 Feb 2010): In my quest to solve this problem, I have discovered some more interesting information. On another forum, someone suggested that I should try running Windows in "Safe Mode With Networking" and see if the problem continues to occur. This was a fantastic suggestion and I don't know why I didn't think of it sooner myself. So, I proceeded to run in Safe Mode with Networking for a number of hours, and amazingly, the "drops" didn't occur once. It was a positive discovery, however, due to the intermittent nature of the original problem, I wasn't completely convinced that the problem was cured. One thing I did note is that the fan on my GFX card was running alot louder than normal. This is due to the fact that I have an ASUS ENGTS250 graphics card (http://www.asus.com/product.aspx?P_ID=B6imcoax3MRY42f3) which had a known problem with a noisy fan until a BIOS update fixed the issue. (See the "Manufacturer Response" here: http://www.newegg.com/Product/Product.aspx?Item=N82E16814121334 for details). Well, running in safe mode had the fan running (incorrectly) at full speed (as it did before the BIOS update), but with an (apparently) stable network connection. Obviously some driver was not loaded for the GFX card when in Safe Mode so this got me thinking about the GFX card (since the very noisy fan was quite obvious when running in Safe Mode). I rebooted into normal mode, and found that Nvidia had a very up-to-date new driver for my GFX card (only about 1 week old), so I downloaded the appropriate driver and installed it. After installation and a reboot, I was able to use my PC for an entire day with NO NETWORK DROPS!!! This was on Saturday. However, on the Sunday, I also had my PC for pretty much the entire day and experienced 2 network drops. No other changes have been made to my PC in this time. So, the story seems to be that updating my graphics card drivers seems to have improved (if not completely fixed) the issue, however, I'm still searching for a proper fix for this problem. Hopefully, this information may help anyone who may have additional ideas as to why this problem is occuring in the first place. (And why does new GFX card drivers have anything to do with the network?) I appreciate everyone's feedback so far. However, I'll have to ask once more if anyone has any further ideas of how to fix this particular problem? Thanks in advance.

    Read the article

  • Cisco: Site-to-site VPN with cisco 878 and ASA weirdness

    - by cpf
    I currently have 2 sites, both connected to each other through 2 firewalls / routers in a site-to-site VPN. Pinging from server to server (Using 2mb/2mb SDSL) through that VPN obviously works, however, at one site, we have another internet connection (7m/400k ADSL), and only the link between the two sites should be on the other connection. All pc's should go over the other connection for internet, just communication between servers & Communication between pc's and the server at the other side should go through there too. What is configured at the moment is the server is using the SDSL directly as default gateway. Since it's not intended to surf anything it is a safe config. PC's are configured on the ADSL as default gateway. Now I wanted to route through everything that uses the range used on the other site, it should be sent from the ADSL modem to the SDSL modem, which has the VPN connection. I figured I could use OSPF to do so, however, OSPF doesn't seem to "detect" the range of the external site. Also (due to bad ip subnetting thanks to the other administrator), the ip used internally as the server on the other site also exists on the internet (causing a lot of confusion), so rdp-ing from our server to the server of the other site works (somehow), but tracerouting on the SDSL router (which should actually, in my opinion, go over the VPN) actually goes all over the internet. My question(s): Why doesn't the SDSL router ping the external ip through VPN, but the server does? Why can't I route from the ADSL router to the SDSL over VPN? I would seriously appreciate some help, since I can't figure out why it does it like this.

    Read the article

  • Can I subnet a subnet?

    - by Portman
    Apologies in advance for the botched terminology. I have read the Server Fault Subnet Wiki but this is more of an ISP question. I currently have a /27 block of public IPs. I use give my router the first address in this pool and then use 1-to-1 NAT for all the servers behind the firewall, so that they each get their own public IP. The router/firewall is currently using (actual addresses removed to protect the guilty): IP Address: XXX.XXX.XXX.164 Subnet mask: 255.255.255.224 Gateway: XXX.XXX.XXX.161 What I would like to do is break out my subnet into two separate /28 subnets. And do this in a way that is transparent to the ISP (i.e., they see me as continuing to operate a single /27). Currently, my topology looks like: ISP | [Router/Firewall] | [Managed Ethernet Switch] / \ \ [Server1] [Server2] [Server3] (etc) Instead, I would like it to look like: ISP | [Switch] / \ [Router1] [Router2] | | | | [S1] [S2] [S3] [S4] (etc) As you can see, this would partition me into two separate networks. I'm struggling with what the correct IP settings would be on Router1 and Router2. Here's what I have right now: Router1 Router2 IP Address: XXX.XXX.XXX.164 XXX.XXX.XXX.180 Subnet mask: 255.255.255.240 255.255.255.240 Gateway: XXX.XXX.XXX.161 XXX.XXX.XXX.161 Note that normally you would expect Router2 to have a gateway of .177, but I'm trying to get them both to use the gateway originally given to me by the ISP. Is subnetting like this in fact possible, or am I completely botching the most basic concepts?

    Read the article

  • AirPort Express Discoverability

    - by andybjackson
    I bought an AirPort Express to enable music in a different part of a friend's house using the AirTunes feature. Unfortunately, iTunes or the AirPort Utility don't reliably discover the existence of the device. If I use the "Configure Other..." function within the AirPort Utility and enter the AirPort Express' IP address and password, then I can reliably get access in a daughter window to configure it. This seems to nudge the underlying AirPort Utility into "finding" and displaying the AirPort Express, which it doesn't do on its own even after clicking the "Rescan" button. iTunes then also seems to cotton on to this discovery and present the AiportExpress as an AirTunes option at the bottom right of iTunes. Things then works as we'd like them to. If I close down the AirPort Utility, then iTunes loses the AirPort Express AirTunes speaker, often giving "An unkown error (-15006) occurred while connecting to the remote speaker". Of course, starting the Airport Utility, forcing it to recognise the Airport Express and then starting iTunes, isn't the ease of use I was after. Background info: iTunes is running on Windows XP. The AirPort Express is running in wireless client mode (i.e. is connecting to an unsecured wireless network in the house with nothing connected to its ethernet port). The network router is a Swisscom Motorola 3347NWG (with firmware 7.8.5r1). I have already tried: Disabling the Windows XP firewall Updating the AirPort Express firmware, the AirPort Utility and the router firmware Ensuring Wireless privacy and similar potetnially problematic router settings are off Solutions, or even just ideas of other things to try would be gratefully received.

    Read the article

  • Destination host unreachable - Windows Server 2008

    - by Doug
    Hi There, I'm working with a windows 2008 domain controller, which I'm having issues connecting to internet resources. A small bit of background, this is a 2008 domain controller that has been added into an existing Win 2k domain, with a goal of replacing the older computers. Both of the older controllers can still access internet resources, and so can all the clients. When I ping Google.ca from the new server, it does resolve to an ip address, but then says "Reply from 192.168.123.20: Destination host unreachable." I'm really at a lost now, I've checked and rechecked my ip configuration, the default gateway is my router, the primary DNS server is the my DC, and the secondary DNS is also my router. The DNS server on the domain has a forwarder added for the router as well. Everything on my local network works just fine, all my internal resources can be resolved. For the time being, I've stopped the Firewall service. I'm not 100% used to Server 2008 yet, but it might be a case of just missing something simple. Thanks for your time.

    Read the article

  • Destination host unreachable - Windows Server 2008

    - by Doug
    Hi There, I'm working with a windows 2008 domain controller, which I'm having issues connecting to internet resources. A small bit of background, this is a 2008 domain controller that has been added into an existing Win 2k domain, with a goal of replacing the older computers. Both of the older controllers can still access internet resources, and so can all the clients. When I ping Google.ca from the new server, it does resolve to an ip address, but then says "Reply from 192.168.123.20: Destination host unreachable." I'm really at a lost now, I've checked and rechecked my ip configuration, the default gateway is my router, the primary DNS server is the my DC, and the secondary DNS is also my router. The DNS server on the domain has a forwarder added for the router as well. Everything on my local network works just fine, all my internal resources can be resolved. For the time being, I've stopped the Firewall service. I'm not 100% used to Server 2008 yet, but it might be a case of just missing something simple. Thanks for your time.

    Read the article

  • Cisco ASA intermittently fails to see traffic

    - by DrStalker
    users | Mikrotik -- Internet | ASA | ServerA and ServerB I'm trying to troubleshoot a problem with a new Cisco ASA 5505. The network design is as above - the Microtik is the existing router, ServerA and ServerB used to plug directly into it. ServerA has IP 10.30.1.10, ServerB has IP 10.30.1.11 The ASA is configured with no NAT, a "allow anything" firewall, and uses the microtik as its default gateway. In effect, it is currently a simple IP router; the firewall and VPN stuff will all come later once the basics are working. Th problem is access to ServerA and ServerB is erratic - sometimes it will work, sometimes it will fail. It can fail for either one of the servers only, or both. When it is working: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show the incoming connections. When it is failing: The Mikrotik logs show ping packets being sent out over the proper interface The ASA logs show nothing reaching the ASA. This can fail for one server only (e.g.: the Mikrotik is putting out packets to 10.30.1.10 and 10.30.1.11, but the ASA is only seeing packets arrive destined for 10.30.1.11) It can fail for one source only (e.g.: ClientA on the users network can ping 10.30.1.11, but clientB cannot) The problem can also be seen from the mikrotik router itself; sometimes it can ping ServerA and ServerB, sometimes it can only ping one of them What could be causing this? I can't think of any possible cause that is intermittent and could explain why the problem may occur for one destination server and not others. edit: Link to ASA config

    Read the article

  • DrayTek 2820 configuration using public IP addresses

    - by Kev
    I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

    Read the article

  • IPCop server slows down download speed

    - by noocyte
    I have an IPCop server running at home, been doing just fine for ~5 months, but last week I suddenly started getting time-outs and slow downloads from the 'net. I first thought that this was my ISP acting up, then I thought it might be one of my 3 switches or some of my cabling. In due order I've tested everything above and found them all to be working as they should. The only factor remaining is my IPCop server. Facts: I've got a 15/15 Mbit line (fiber) and I get ~15 Mbit upload, but only 0.5 Mbit download with the IPCop box as router (ISP router set in bridge mode). If I connect without the IPCop box (using the ISP router) I get ~12 Mbit upload and ~15 Mbit download. The load on the IPCop box appears to be light and it used to handle this traffic just fine 2 weeks ago. The memory usage is ~60%, I tried to restart it and test again, the memory fell to ~50% then (5 months of uptime). I'm thinking that one of my nics are busted, but I'm sort of perplexed that this could be the outcome; slow download but full speed upload. Anybody ever seen that happening before? Could it just be one of the nics that needs to be replaced? Will try that as soon as I can get my hands on a couple of new ones.

    Read the article

  • Server and Network Lag

    - by DanSpd
    At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

    Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >