Search Results

Search found 6670 results on 267 pages for 'speed dial'.

Page 77/267 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• DD-WRT/openwrt question

  - by Shiki

  Can I squeeze more speed out of my router (when it comes to USB attached storage device on it) with open/DD wrt? (Sorry I don't really know such firmwares.) (Guess it works with ntfs-3g? I don't know.) Feel free to make this a real question. Basically the question: Does the change worth it in the terms of speed? (My router is a TP-Link WR1043N. Edited it out of the question since it would make it too specified.)

  Read the article

• S.M.A.R.T - Predictive Failure Count

  - by Bastien974

  I'm monitoring my IBM ServeRAID M5015 controller for RAID status with MegaCLI, I have this on one of the disk : Enclosure Device ID: 252 Slot Number: 6 Enclosure position: 0 Device Id: 14 Sequence Number: 2 Media Error Count: 32 Other Error Count: 0 Predictive Failure Count: 18 Last Predictive Failure Event Seq Number: 8119 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.464 GB [0x22cee000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c50042c319c9 SAS Address(1): 0x0 Connected Port Number: 5(path0) Inquiry Data: IBM-ESXSST9300653SS B6336XN04HC10525B633 IBM FRU/CRU: 81Y9671 FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive: Not Certified Drive Temperature :33 Celsius What does this mean exactly ? I can't find an exact description, is there a way to have more details ? The RAID array has the Optimal state. Media Error Count: 32 Predictive Failure Count: 18 Is there a way through the CLI to power-on the front LED so I physically know which disk I need to replace ?

  Read the article

• udp expected behaviour not responding to test result

  - by ernst

  I have a local network topology that is structured as follows: three hosts and a switch in the middle. I am using a switch that supports 10,100,1000 Mbit/s full/half duplex connection. I have configured the hosts with a static ip 172.16.0.1-2-3/25. This is the output of ifconfig eth0 Link encap: Ethernet HWaddr ***** inet addr:172.16.0.3 Bcast:172.16.0.127 Mask:255.255.255.128 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 The output on H1 and H2 is perfectly matchable They are mutually reachable since i have tested the network with ping. I have forced the ethernet interface to work at 10M with ethtool -s eth0 speed 10 duplex full autoneg on this is the output of ethtool eth0 supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full S upported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Full Advertised pause frame use: Symmetric A dvertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) drv probe link timer ifdown ifup rx_err tx_err Link detected: yes – I am doing an experimental test using nttcp to calculate the GOODPUT in the case that H1 and H2 at the same time send data to H3. Since the three links have the same forced capability and the amount of arrving data speed is 10 from H1+10 from H2--20M to H3 it would be expected a bottleneck effect and, due to the non reliable nature of udp, a packet loss. But this doesn't appen since the output of nttcp application shows the same number of byte sended and received. this is the output of nttcp on h3 nttcp -T -r -u 172.16.0.2 & nttcp -T -r -u 172.16.0.1 [1] 4071 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 13.74 0.05 4.8848 1398.0140 2049 149.14 42684.8 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 14.02 0.05 4.7872 1398.0140 2049 146.17 42684.8 1 8388608 13.56 0.06 4.9500 1118.4065 2051 151.28 34181.1 1 8388608 13.89 0.06 4.8310 1198.3084 2051 147.65 36623.0 – How is this possible? Am i missing something? Any help will be gratefully apprecciated, Best regards

  Read the article

• How to find the /dev name of my USB device

  - by mustafa

  I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

  Read the article

• Why do my download speeds drastically vary during a download?

  - by J. Anthony Carter

  I watch the download speed rise and fall like waves in a storm. At night, during low bandwidth usage I have achieve speeds as high as 3.23 M/sec but the watch them decline to 250 K/sec. and then climb back up. Over and over. During the day my best is around 1.67 M/sec with lows into the 65 K/sec. On top of this, why does a download need to slow down when approaching the end of the download? It's not like a multi-hundred ton train needing to decrease speed as it approaches the station.

  Read the article

• How to increase the disk cache of Windows 7

  - by Mark Christiaens

  Under Windows 7 (64 bit), I'm reading through 9000 moderately sized files. In total, there is more than 200 MB of data. Using Java (JDK 1.6.21) I'm iterating over the files. The first 1400 or so go at full speed but then speed drops off to 4ms per file. It turns out that the main cost is incurred simply by opening the files. I'm opening the files using new FileInputStream (and of course closing them in time to avoid file leaks). After some investigating, I see that Windows' disk cache is using only 100 MB or so of RAM although I have 8 GiB available. I've tried increasing the cache size using the CacheSet tool but any values I provide are considered out of range. I've also tried enabling the LargeSystemCache registry key but (after rebooting) the CacheSet tool still indicates I'm using 100 MB of cache (and doesn't increase during the test run). Does anybody have any suggestions to "encourage" Windows 7 to cache my 9000 files?

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• low performance on HPC cluster (sge) when running multiple jobs

  - by Yotam

  O know this is a long-shot but I'm clueless here. I'm running several computer simulations on High Performance Computation cluster (HPC) of oracale grid engine (sge). A single job runs at a certain speed (roughly 80 steps per second) when I add jobs to the machine, at a certain treshhold, the speed is recuded by two. On one machine (I don't know the cpu kind) the treshold is 11 jobs for 16 cpu's. On another one with the same number and kind of cpu's , the treshold is 8. I thought at first that this is a memory issue but each job takes about 60MB - 100MB and I have 16GB of ram on each of those machine. Did any of you encountered such a problem? is there any way to analyz this? Thanks.

  Read the article

• Under $300 computer

  - by Moshe

  Preferably not a netbook, please. should support Windows 7 at a normal speed.

  Read the article

• LACP : Cisco ASA 5515 & Switch ProCurve 2920

  - by user979276

  I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created a Port-Channel like that : interface GigabitEthernet0/0 nameif outside security-level 0 ip address 192.168.1.3 255.255.255.0 standby 192.168.1.4 ! interface GigabitEthernet0/1 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface GigabitEthernet0/2 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface Port-channel1.1 vlan 1 nameif inside security-level 100 ip address 192.168.8.1 255.255.255.0 standby 192.168.8.2 ! interface Port-channel1.10 vlan 10 nameif guest security-level 50 ip address 172.16.100.2 255.255.255.224 standby 172.16.100.3 ! interface Port-channel1.16 vlan 16 nameif dmz security-level 50 ip address 192.168.16.1 255.255.255.0 standby 192.168.16.2 On the switch, I created a trunk LACP capable with the port 1 and 2 on each switch, force the speed to 1000 and put the port un full duplex mode. BUT this is not working... I tried many things and I can't make it work. In this configuration, I can't ping anything between my ASA and my Switch (or any object connected). Here what I get on my ASA : Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State ----------------------------------------------------------------------------- Gi0/2 SP not-bndl 32768 0x1 0x1 0x3 0xc Gi0/1 FP not-bndl 32768 0x1 0x1 0x2 0x6 And on the Switchs : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Broken Yes Failure 2 Active trk1 Broken Yes Failure If I change the Cisco interface to LACP mode On, I can ping the switch from the ASA but nothing other objects conneted on the switch. If I look at the statut of LACP on the switch I see this : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Up No Success 2 Active trk1 Up No Success I don't have any clue on what's going on so If someone have any idea and help me on this, it would be great ! Feel free to ask me anything if you need any more information ! Thanks a lot !

  Read the article

• Currently well suited SATA2-SSDs for Laptop usage

  - by danilo

  I am looking for a solid state drive for my laptop. My dillemma: I have been waiting for the new Intel SSDs since Q3/2010, as I've heard they should be better and cheaper, due to lower memory manufacturing costs. Now it looks like the new Intel drives are very fast, but still expensive. I would still buy one of them if I could benefit from the full speed. My hardware only has a SATA-2 port though. Thus, my question: Is it worthwhile to buy one of those new Intel SSDs made for SATA-3 if I won't be able to use the full speed? Are there any other promising new SSDs that will be released soon? (Inside the next 1-2 months) If I wouldn't make a good deal buying the newer, faster drives, what drives can you recommend? I don't consider this question subjective, as I am mainly looking for answers concerning the SATA-2/SATA-3 conflict.

  Read the article

• Need to upgrade DDR2 RAM on HP Desktop

  - by jds

  I have this HP Pavilion Desktop. As you can see, that page says the memory speed supported is PC2-4200. It currently has a 512 MB stick - CPU-Z Screenshots: hxxp://i41.tinypic.com/j5clj6.jpg and hxxp://i39.tinypic.com/20tldlc.jpg However, a crucial.com scan gives a slightly different report - hxxp://crucial.com/systemscanner/viewscanbyid.aspx?id=5718CFE831D926C3 It says the system can support PC2-5300 memory. So my question is which one should I trust? I want to upgrade the computer's ram to 2 GB (the maximum supported), because XP Media Center is giving me problems and I will install Windows 7 on this. PC2-6400 is the most common DDR2 memory I have been able to find here in the market. Will it cause any problems if I install 2 × 1 GB PC2-6400 DDR2 memory sticks (in dual channel) in this computer, (afaik, it will just run at the lower speed of 533 MHz, or whatever the motherboard supports), or do I absolutely need to get PC2-4200 sticks?

  Read the article

• Windows - Force Wi-Fi to N mode

  - by Frederick Marcoux

  I bought a month ago the D-Link DWA-160 Xtreme N Dual Band USB Adapter and I wonder about the speed. I have a 60Mbps but the speed is never above 300Kbps when I browse Internet or download something. Even from Microsoft or Apple (the fastest server I found). Now on Windows 8, we can see the Wi-Fi stats in Task Manager, there they are: Notice the red rectangle. The signal is 3/5 and I'm about 5 meters far from my router. An Apple Time-Capsule. Also, the connection type is 802.11g, I want N. I made this config in my Device Properties: Does anyone figured out to force the 802.11n in Windows? (Windows 8 preferably)

  Read the article

• What affects video encoding speeds?

  - by Pig Head

  FRAPs doesn't compress its videos when you record, so the files are enormous. In a long recording you can get up to a few hundred gigabytes. Obviously, usually you would need to convert/compress them. What affects the speed of this? I don't think the RAM does, as when I converted 600 gb my RAM usage only went to 6 gig, but the processor was at 100%, which is surprising as I have a 6 core processor @ 3.46 ghz. Would clock speed or cores help the most?

  Read the article

• Nvidia 9 series or Intel HD 2000? [closed]

  - by EApubs

  I just tested an Nvidia 9300 GS card with a Intel Corei3 HD 2000 graphics system. Here is the windows experience index scores I got : Nvidia 9300 GS : Base Score 3.9 Processor : 7.1 Memory : 7.5 Graphics : 3.9 Gaming Graphics : 5.1 Hard Disk : 5.9 Intel HD 2000 : Base Score : 5.2 Processor : 7.1 Memory : 5.9 Graphics : 5.2 Gaming Graphics : 5.8 Hard Disk : 5.9 My questions are : When using Intel HD graphics, it reduces the score of my Ram! How is that possible? It checks the speed of the ram. Not the size (i think). Intel graphics take some of the ram space but how can that effect the speed? From both of them, what will be the good choice?

  Read the article

• Large file copy from NFS to local disk performance drop

  - by Bernhard

  I'm trying to copy a 200GB file from an NFS mount to a local disk. The local disk is an XFS filesystem on a LVM on top of a RAID 5 system (hardware RAID controler). I'm using rsync to monitor the transfer speed. At the beginning the IO speed is about 200MB/s, stable for the first 18GB. But then the performance drops by a factor of 10-20 and never recovers to the initial rate. Sometimes it reaches about 50-100MB/s but just for a few seconds and then the process seems to hang for a bit. At the same time all file-stat operations on the target filesystem are blocking for a long time (minutes). Also interrupting the copy process blocks for several minutes, a sub-sequent delete of the partly copied file takes also several minutes. Any ideas what could be causing this?

  Read the article

• 32 vs 64-bit software for same machine?

  - by GorillaSandwich

  What is the difference between 32 and 64-bit software? My understanding is that 64-bit can use more RAM, if it's available, because it has a larger address space for it. Is this correct? And, specifically: If I have a 64-bit operating system with lots of RAM, and I install, say, the 32-bit version of MySQL instead of the 64-bit version, will it be unable to use all the available RAM and therefore run slower than the 64-bit version might on the same machine (assuming RAM becomes the bottleneck before processing speed or disk access speed or whatever)? If I have a 32-bit operating system and I install a 64-bit piece of software on it, will it (probably) fail to run?

  Read the article

• Failed to start up after upgrading software in ubuntu 10.10

  - by Landy

  I've been running Ubuntu 10.10 in a physical x86-64 machine. Today Update Manager reminded me that there are some updates to install and I confirmed the action. I should had read the update list but I didn't. I can only remember there is an update about cups. After the upgrading, Update Manager requires a restart and I confirmed too. But after the restart, the computer can't start up. There are errors in the console. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. [xxx]usb 1-8: new high speed USB device using ehci_hcd and address 3 [xxx]usb 2-1: new full speed USB device using ohci_hcd and address 2 [xxx]hub 2-1:1.0: USB hub found [xxx]hub 2-1:1.0: 4 ports detected [xxx]usb 2-1.1: new low speed USB device using ohci_hcd and address 3 Gave up waiting for root device. Common probles: - Boot args (cat /proc/cmdline) - Check rootdelay=(did the system wait long enough) - Check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.35-22-generic/modules.dep: No such file or directory ALERT! /dev/sda1 does not exist. Dropping to a shell! BusyBox v1.15.3 (Ubuntu 1:1.15.3-1ubuntu5) built-in shell(ash) Enter 'help' for a list of built-in commands. (initramfs)[cursor is here] At the moment, I can't input anything in the console. The keyboard doesn't work at all. What's wrong? How can I check boot args or "root=" as suggested? How can I fix this issue? Thanks. =============== PS1: the /dev/sda1 is type ext4 (rw,nosuid,nodev) PS2: the /dev/sda1 can be mounted and accessed successfully under SUSE 11 SP1 x64.

  Read the article

• RAID--0 " TWO " DRIVES SSD ONLY Should I use on-board / Software RAID OR a RAID Card / Control

  - by Wes

  I am looking at going with a TWO Drive Only SSD RAID-0 Configuration And was wondering if I would get better performance / Speed from the Use of a RAID Controller / Card Verses just using the Software RAID on my Mother Board. I have herd conflicting reports , Again I only Plan on Running " 2 " SSD Drives in RAID-0 Config I have No- problem spending the extra money for a good controller but only if I am going to benifit performance wise , Otherwise if there is no notable Gain I will just use the Software RAID that my HP-180-T came with Intel- 3.33 GHZ , 6-Core , 12-GB of DDR-3. I have a huge External drive for All Storage and am not concerned about Data loss just looking for pure speed. And if a Controller will benifit my performance Wht type of card would one suggest?

  Read the article

• Computer turns off and on after start ..then goes dead

  - by Shiki

  I built a new PC from the following components: - CPU: Intel Core i7 950 - MB: Gigabyte X58A-UD3R - RAM: 2x2gb i7 Corsair memory - VGA: Zotac AMP2 GTX260 - HDD: 1 GreenSATA HDD (Western Digital 500gb RE2) When I turn it on, it goes for a few seconds, fans at maximum speed, then turns off. The again, it starts by itself.. and goes with fans on max speed, nothing happens. First I suspected my PSU. It's a Chieftec 450AA PSU. After I borrowed a Chieftec 550AA PSU, I tried to start with that. Exact same story. Any idea ? Do I need a bigger PSU? Reason why its not localized. I never seen this turn on, off, on. If you give answer for that, it would already help people like me, with the same problem.

  Read the article

• Flash stream makes my internet slow and cpu rush

  - by user1225840

  When I try to watch a live Flash stream, my CPU usage goes up to 75% and my Internet speed goes down. If I run a test before the video-stream, my speed is ~40/10Mbps and during the stream it drops to 0.1-0.5Mbps. The stream is laggy and I can only watch one to two seconds at a time, start/stop/start/stop. I have cleared my history, cache, cookies, temp files, and so on. I have searched for malware and took care of that. I have updated my drivers, reinstalled Flash and everything else I can think of, but it remains slow. I had this problem before and it just started working normally from one day to another. Could it be a hardware problem?

  Read the article

• Apps not starting on Mac OS X Lion

  - by KPS

  I have a strange problem, some apps that I download do not launch. There are 2 scenarios The application starts but keeps bouncing, once I click the bouncing icon in the tray it disappears. The process also closes in activity monitor The application fails to start, how ever many times I launch it, it refuses. The process does not even show up in activity monitor What I have done so far to resolve: Repaired permissions Clear all cache/temp using CleanMyMac Used DiskWarrior via OS and not during boot Additional Info: Model Name: MacBook Pro Model Identifier: MacBookPro5,2 Processor Name: Intel Core 2 Duo Processor Speed: 2.8 GHz Number of Processors: 1 Total Number of Cores: 2 L2 Cache: 6 MB Memory: 8 GB Bus Speed: 1.07 GHz Boot ROM Version: MBP52.008E.B05 SMC Version (system): 1.42f4

  Read the article

• google video chat works faster on local LAN

  - by bashrc

  Recently the internet speed on our college LAN has dropped drastically. ( Avg file download speed 13 Kbps :( ). However g-talk's video chat remains unbelievably fluent when done with someone within the college's LAN. However video chat is practically impossible for anyone else who is not in the college network. My college has a proxy server through which all computers inside the college connect to the internet. I suspect its due to the proxy server. Also how g-talk maintains video chat? Is it something in the mechanism that speeds up video chat between two clients with the same IP? Since all computers use the same proxy,their IP would appear to be the same to google server.

  Read the article

• IPv6 routing to another interface

  - by Robert

  I'm trying to get an IPv6 enabled router to forward data from one interface to the other and I'm having issues. When following this example (http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba6106.shtml) I am able to get full connectivity between all 3 routers in my simulator. However when I try to use only 1 router; I can't get connectivity to the other interfacs on the same router. My PC is directly attached to FA 0/1 and it can ping the router's interface. However it can not ping any other interface on the router(which unless I'm missing something it should be able to do). The router on the other hand can ping everything. I thought static routes might help; but the router already has routes for everything. I'm thinking the packet should come in; router looks up the destination in it's ipv6 routing table and then realizes it's for itself, and should respond. I thought maybe it couldn't respond directly; so I tried pinging a device like 2001:0000:0000:1000::2, but i don't get a response. I'm running on IOS 12.4. I'm missing something(hopefully simple), but I just can't see what it is. With only 1 router; how do I enable my PC to talk to the other subnets? Thank you in advance, Robert Topology: R1 FA 0/0: 2001:0000:0000:0000::1/52 FA 0/1: 2001:0000:0000:1000::1/52 FA 1/0: 2001:0000:0000:2000::1/52 Loopback 0: 2001:0000:0000:3000::1/52 PC: 2001:0000:0000:2000::2/52 PC plugs directly into FA 1/0 on the router. --- Configuration --- ipv6 cef ipv6 unicast routing interface Loopback0 no ip address ipv6 address 2001:0000:0000:3000::1/52 ipv6 enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000::1/52 ipv6 enable ! interface FastEthernet0/1 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:1000::1/52 ipv6 enable ! interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:2000::1/52 ipv6 enable --- end of config --- --- routing table --- IPV6Lab#show ipv6 route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2001:0000:0000::/52 [0/0] via ::, FastEthernet0/0 L 2001:0000:0000::1/128 [0/0] via ::, FastEthernet0/0 C 2001:0000:0000:1000::/52 [0/0] via ::, FastEthernet0/1 L 2001:0000:0000:1000::1/128 [0/0] via ::, FastEthernet0/1 C 2001:0000:0000:2000::/52 [0/0] via ::, FastEthernet1/0 L 2001:0000:0000:2000::1/128 [0/0] via ::, FastEthernet1/0 C 2001:0000:0000:3000::/52 [0/0] via ::, Loopback0 L 2001:0000:0000:3000::1/128 [0/0] via ::, Loopback0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 --- end of routing table ---

  Read the article

• Laptop is super slow on network

  - by Gary

  So on our network we have a bunch of wireless macs and window Operating laptops, we have a network setup with 802.11g,b,n. All the laptops seem fine except one which is only getting speeds of 54Mb. I have changed the encryption from AES to TKIP and reset the connection, i have updated the drivers, tried plugging it into the LAN and still same slow speed. Apparently the laptop with the slow speed is fine on other networks. I don't know what to do, can anyone help me?

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >