Search Results

Search found 13930 results on 558 pages for 'dev center'.

Page 78/558 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >

• Hot-swap drive got new name, can I change it on-the-fly?

  - by T.J. Crowder

  One of the HDDs in my server's RAID config failed, so I took it out of the array and had the data center hot-swap it. They've done that, but now the new drive is /dev/sdc rather than /dev/sda. I suspect — correct me if I'm wrong — that if I reboot the server, it will be /dev/sda again, so I'm hesitant to add it back to the array as /dev/sdc because I don't want to lay a trap for myself to fall into on the next reboot. I'd just as soon not reboot the server if I don't need to (if I do need to, well, too bad for me). Is there a way I can change the device name from /dev/sdc to /dev/sda without rebooting? This is on Ubuntu 10.04 LTS. It's an md array ("Linux Software RAID"), where currently one of the devices (there are a couple of them) looks like this ("degraded" because I've removed the old /dev/sda from it): # mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Sun Oct 11 21:07:54 2009 Raid Level : raid1 Array Size : 97536 (95.27 MiB 99.88 MB) Used Dev Size : 97536 (95.27 MiB 99.88 MB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 30 09:31:16 2011 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 UUID : 496be7a5:ab9177ed:7792c71e:7dc17aa4 Events : 0.112 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed Thanks, Update: Reading through the kernel md documentation, I suspect that if the name changes on reboot, it won't matter. (Good design, that.) Here's why: Boot time autodetection of RAID arrays When md is compiled into the kernel (not as module), partitions of type 0xfd are scanned and automatically assembled into RAID arrays. This autodetection may be suppressed with the kernel parameter "raid=noautodetect". As of kernel 2.6.9, only drives with a type 0 superblock can be autodetected and run at boot time. The kernel parameter "raid=partitionable" (or "raid=part") means that all auto-detected arrays are assembled as partitionable. I do have md compiled into the kernel, so I'm rebuilding the array now and will do the reboot to see what happens. Even if it works, the above doesn't answer the question I actually asked, so unless someone comes along and answers that question in the meantime (I'd be interested, even if it's not necessary for what I'm doing this very moment), I'll just delete the question to keep noise down.

  Read the article

• How do i mount my SD Card? I am using ubuntu 10.04

  - by shobhit

  root@shobhit:/media# lsusb Bus 002 Device 017: ID 14cd:125c Super Top Bus 002 Device 003: ID 0c45:6421 Microdia Bus 002 Device 002: ID 8087:0020 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 011: ID 413c:8160 Dell Computer Corp. Bus 001 Device 006: ID 413c:8162 Dell Computer Corp. Bus 001 Device 005: ID 413c:8161 Dell Computer Corp. Bus 001 Device 004: ID 138a:0008 DigitalPersona, Inc Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 001 Device 002: ID 8087:0020 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lspci -v -nn 00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fbc08000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at fbc07000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a6) (prog-if 01) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=20, subordinate=20, sec-latency=32 Capabilities: [50] Subsystem: Dell Device [1028:0441] 00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b0b] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b2f] (rev 06) (prog-if 01) Subsystem: Dell Device [1028:0441] Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 29 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at fbc06000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 06) Subsystem: Dell Device [1028:0441] Flags: medium devsel, IRQ 3 Memory at fbc05000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem [8086:3b32] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 3 Memory at fbc04000 (64-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 3 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 12:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4727] (rev 01) Subsystem: Dell Device [1028:0010] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number cb-c0-8b-ff-ff-38-00-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl 13:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 28 I/O ports at e000 [size=256] Memory at d0b04000 (64-bit, prefetchable) [size=4K] Memory at d0b00000 (64-bit, prefetchable) [size=16K] Expansion ROM at fba00000 [disabled] [size=128K] Capabilities: [40] Power Management version 3 Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4 Capabilities: [cc] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-03 Kernel driver in use: r8169 Kernel modules: r8169 root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lshw shobhit description: Portable Computer product: Vostro 3500 vendor: Dell Inc. version: A10 serial: FV1L3N1 width: 32 bits capabilities: smbios-2.6 dmi-2.6 smp-1.4 smp configuration: boot=normal chassis=portable cpus=2 uuid=44454C4C-5600-1031-804C-C6C04F334E31 *-core description: Motherboard product: 0G2R51 vendor: Dell Inc. physical id: 0 version: A10 serial: .FV1L3N1.CN7016612H00PW. slot: To Be Filled By O.E.M. *-cpu:0 description: CPU product: Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 slot: CPU 1 size: 1197MHz capacity: 2926MHz width: 64 bits clock: 533MHz capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp x86-64 constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida arat tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: id=4 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 3MiB capacity: 3MiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 4.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 width: 64 bits capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 width: 64 bits capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 width: 64 bits capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 width: 64 bits capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 width: 64 bits capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 width: 64 bits capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a width: 64 bits capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b width: 64 bits capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c width: 64 bits capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d width: 64 bits capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e width: 64 bits capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f width: 64 bits capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 3GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT112S6TFR8C-H9 vendor: AD80 physical id: 0 serial: 5525C935 slot: DIMM_A size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT125S6TFR8C-H9 vendor: AD80 physical id: 1 serial: 3441D6CA slot: DIMM_B size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A10 (10/25/2010) size: 64KiB capacity: 1984KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 size: 1197MHz capacity: 1197MHz capabilities: vmx ht cpufreq configuration: id=4 *-logicalcpu:0 description: Logical CPU physical id: 4.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 capabilities: logical *-pci description: Host bridge product: Core Processor DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 18 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 18 width: 64 bits clock: 33MHz capabilities: msi pm bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:30 memory:fac00000-faffffff memory:c0000000-cfffffff(prefetchable) ioport:f080(size=8) *-communication UNCLAIMED description: Communication controller product: 5 Series/3400 Series Chipset HECI Controller vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc09000-fbc0900f *-usb:0 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fbc08000-fbc083ff *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:22 memory:fbc00000-fbc03fff *-pci:0 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:24 ioport:2000(size=4096) memory:bc000000-bc1fffff memory:bc200000-bc3fffff(prefetchable) *-pci:1 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:25 ioport:3000(size=4096) memory:fbb00000-fbbfffff memory:bc400000-bc5fffff(prefetchable) *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:8b:aa:d8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=10.0.1.50 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbb00000-fbb03fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 3 vendor: Intel Corporation physical id: 1c.2 bus info: pci@0000:00:1c.2 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:26 ioport:e000(size=4096) memory:fba00000-fbafffff ioport:d0b00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 03 serial: 78:2b:cb:cc:0e:2a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:28 ioport:e000(size=256) memory:d0b04000-d0b04fff(prefetchable) memory:d0b00000-d0b03fff(prefetchable) memory:fba00000-fba1ffff(prefetchable) *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:27 ioport:d000(size=4096) memory:fb000000-fb9fffff ioport:d0000000(size=10485760) *-usb:1 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fbc07000-fbc073ff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a6 width: 32 bits clock: 33MHz capabilities: pci bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 06 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 5 Series/3400 Series Chipset 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi1 version: 06 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:29 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fbc06000-fbc067ff *-disk description: ATA Disk product: WDC WD3200BEKT-7 vendor: Western Digital physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WX21AC0W1945 size: 298GiB (320GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=77e3ed41 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: aa69-51c0 size: 98MiB capacity: 100MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-04-03 02:00:15 filesystem=ntfs label=System Reserved state=clean *-volume:1 description: Windows NTFS volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 3.1 serial: 9854ff5c-1dea-a147-84a6-624e758f44b8 size: 48GiB capacity: 48GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-10 13:55:31 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:2 description: Extended partition physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 size: 48GiB capacity: 48GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 1952MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 46GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,barrier=1,data=ordered state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/56AA8094AA807273 version: 3.1 serial: 22a29e8d-56c7-9a4a-adea-528103948f6d size: 200GiB capacity: 200GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-02 20:17:15 filesystem=ntfs modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-cdrom description: DVD-RAM writer product: DVD+-RW TS-L633J vendor: TSSTcorp physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 version: D200 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 06 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fbc05000-fbc050ff ioport:f000(size=32) *-generic UNCLAIMED description: Signal processing controller product: 5 Series/3400 Series Chipset Thermal Subsystem vendor: Intel Corporation physical id: 1f.6 bus info: pci@0000:00:1f.6 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc04000-fbc04fff *-scsi physical id: 2 bus info: usb@2:1.1 logical name: scsi15 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@15:0.0.0 logical name: /dev/sdb I have tried all options like fdisk /dev/sdb , pmount /dev/sdb but nothing is working .Pls guide me

  Read the article

• How to write a Media Center plugin like the Netflix plugin? Source code/reference samples?

  - by Vin

  I am looking to write a Windows Media Center plugin just like the Netflix WMC plugin. Once logged in, I know the streaming urls that I need to hook in to. Any source code, reference samples would be great. Found one on codeplex for swedish TV channels, but right now it's not working for some reason... Previously asked the following question, with no answers, so updated with a question asked in a easy to relate fashion Host a streaming video in my client, from a streaming url that is behind a login session? I am building a Silverlight 4 desktop client to show streaming video from a site that is login based. So that website has a Silverlight player that does streaming video, the player is behind a login sesion, so just by getting the url from fiddler and trying to play it in my Silverlight 4 desktop client won't work. Actually after that, I want to build a Windows Media Center plugin to build a Netflix-like client, that allows login through WMC and then allows you to watch streaming video. Any pointers on how to go about doing any of this?

  Read the article

• WCF identity when moving from dev to prod. environment

  - by Anders Abel

  I have a web service developed with WCF. In the development environment the endpoint has the following identity section under the endpoint configuration. <identity> <dns value="myservice.devdomain.local" /> </identity> myservice.devdomain.local is the dns name used to reach the development version of the service. The binding used is: <basicHttpBinding> <binding name ="myBinding"> <security mode ="TransportCredentialOnly"> <transport clientCredentialType="Windows"/> </security> </binding> </basicHttpBinding> I am about to put this into production. The binding will be the same, but the address will be a new production address myservice.proddomain.local. I have planned to change the dns value in the configuration to myservice.proddomain.local in the production environment. However this MSDN article on WCF Identity makes me worried about the impact on the clients when I change the identity. There are two clients - one .NET and one Java using this service. Both of those have been developed against the dev instance of the service. The idea is to just reconfigure the endpoint used by the clients, without reloading the WSDL. But if the identity is somehow part of the WSDL and the identity changes when deploying to prod that might not work. Will the new identity in the prod version cause issues for the clients that were developed using the dev wsdl? Do the Java and the .NET clients handle this differently?

  Read the article

• How did I center a jpanel in a jpanel with netbeans?

  - by Jim Nordlander

  With Netbeans I've succeded center a jpanel with fixed size, within an other jpanel. Now I can't repeat it - only copy it. How did I do? (or should I do to center x and y a jpanel with fixed size in another jpanel). The result differs in code: Working - search for .addContainerGap( and see next not working: javax.swing.GroupLayout center3Layout = new javax.swing.GroupLayout(center3); center3.setLayout(center3Layout); center3Layout.setHorizontalGroup( center3Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGap(0, 1064, Short.MAX_VALUE) .addGroup(center3Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGroup(center3Layout.createSequentialGroup() .addContainerGap(30, Short.MAX_VALUE) .addComponent(mainPanel3, javax.swing.GroupLayout.PREFERRED_SIZE, javax.swing.GroupLayout.DEFAULT_SIZE, javax.swing.GroupLayout.PREFERRED_SIZE) .addContainerGap(30, Short.MAX_VALUE))) ); center3Layout.setVerticalGroup( center3Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGap(0, 650, Short.MAX_VALUE) .addGroup(center3Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGroup(center3Layout.createSequentialGroup() .addContainerGap(23, Short.MAX_VALUE) .addComponent(mainPanel3, javax.swing.GroupLayout.PREFERRED_SIZE, javax.swing.GroupLayout.DEFAULT_SIZE, javax.swing.GroupLayout.PREFERRED_SIZE) .addContainerGap(23, Short.MAX_VALUE))) ); Not working - search for .addGap compared with above working. javax.swing.GroupLayout center2Layout = new javax.swing.GroupLayout(center2); center2.setLayout(center2Layout); center2Layout.setHorizontalGroup( center2Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGap(0, 1073, Short.MAX_VALUE) .addGroup(center2Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGroup(center2Layout.createSequentialGroup() .addGap(0, 34, Short.MAX_VALUE) .addComponent(mainPanel2, javax.swing.GroupLayout.PREFERRED_SIZE, javax.swing.GroupLayout.DEFAULT_SIZE, javax.swing.GroupLayout.PREFERRED_SIZE) .addGap(0, 35, Short.MAX_VALUE))) ); center2Layout.setVerticalGroup( center2Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGap(0, 654, Short.MAX_VALUE) .addGroup(center2Layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGroup(center2Layout.createSequentialGroup() .addGap(0, 25, Short.MAX_VALUE) .addComponent(mainPanel2, javax.swing.GroupLayout.PREFERRED_SIZE, javax.swing.GroupLayout.DEFAULT_SIZE, javax.swing.GroupLayout.PREFERRED_SIZE) .addGap(0, 25, Short.MAX_VALUE))) ); I've looked side by side in properties etc - please help! :)

  Read the article

• Configuring zend to use gmail smtp: Windows Apache dev-environment: "Could not open socket" error - repeatedly - going mad

  - by confused

  My dev environment is Win XP SP2 / Apache 2.something PHP 5.something_or_other My prod env is Linux Ubuntu / Apache 2.something_else PHP 5.something_or_other_else The code is all Zend Framework Version: 1.11.1 I can telnet to: smtp.gmail.com 465 from the PC. I have Mercury configured on my PC to use gmail as it's smtp host and it works just fine. (MercuryC SMTP Client). Mercury is set to use port 465 and SSL on smtp.gmail.com -- No problem. Zend mail works just fine on my production environment using the production mail server to send out mail. It's the same basic application.ini but with different values in the mail variables. On my local PC dev setup, my application.ini contains: (same values as I use in Mercury) mail.templatePath = APPLICATION_PATH "/emails" mail.sender.name = "myAccount" mail.sender.email = "[email protected]" mail.host = smtp.gmail.com mail.smtp.auth = "login" mail.smtp.username = "[email protected]" mail.smtp.password = "myPassWord" mail.smtp.ssl = "ssl" mail.smtp.port = 465 I have been doing trial and error for hours trying to get a single email out with no success. In every case, regardless of server or port settings it throws an error and reports: Could not open socket. Both Apache and Mercury Core are exceptions in my Windows Firewall config. Mercury seems to be having no problem. I have searched stackoverflow before posting this and have been googling for hours -- with no success. I am slowly losing my mind I would be very much obliged for any tip as to what might be wrong. Thanks for reading. =================== BTW When I use the SAME application.ini values on my local PC as on the production host, I get the same "Could not open socket" error. Those values are: mail.templatePath = APPLICATION_PATH "/emails" mail.sender.name = "otherUser" mail.sender.email = "[email protected]" mail.host = smtp.otherServer.com mail.smtp.auth = "login" mail.smtp.username = "[email protected]" mail.smtp.password = "otherPAssWord" mail.smtp.ssl = "ssl" mail.smtp.port = 465 I know these work in the production (Ubuntu) environment. I'm utterly baffled.

  Read the article

• Center a TextBox over the top of a ScrollViewer in WPF.

  - by Eric

  I have a MainView that contains a navigation bar which selects one of many XAML pages to be displayed in the page view pane. The MainView contains a ScrollViewer around the pages. This allows the pages to be whatever size they need to be and the MainView's ScrollViewer scrolls them. This all works great. On one of the pages, I need to (sometimes) center a TextBox in the middle of the page view pane (over the top of the page content). This was easily done by placing both the page content and the TextBox overlapping each other in a Grid (and I hide the TextBox as necessary). This all seems to work great. However, if the page content grows to be larger than the pane, the TextBox is centered not on the pane, but on the full page content. Thus, it moves from center screen down and/or to the right (and eventually off the screen). Bummer. Options: Remove the ScrollViewer from the MainView. This would require placing one on every page! Argh. Do option #1, and create a ScrolledPage base class. This is a lot of work, and I'm worried about tools issues (Blend issues). It also requires changing every page (to subclass this page). Somehow override the ScrollViewer on just this page. Then, place another ScrollViewer on the page content to Scroll it. Option 3 seems preferable, because it contains the issue to just modifying this page (instead of changing the rest of the pages). However, I can't figure out how to do it. Ideas? Thanks in advance! Eric

  Read the article

• I need to move a dived CSS module into the center of the page...

  - by JackMcE

  I'm building a website for someone and they wanted the text and bulk of the information to be centered on the page. Problem is I can get everything contained in a tag and then assign the class, but I can't get the whole thing to center. It always hangs to the left even if I apply centering to the div class. I guess you could say that it is stuck on the left side of the page when I want everything to be centered. I would just make everything format larger but they want some space left in the background for the color and maybe some imagery later on. They haven't made up their minds. If you want to take a look here is the link where I'm building or testing stuff. I know the header and such needs to be re proportioned to fit with everything, but just as a frame of reference. Don't worry about the header, just know that I want the white text information area with the purple border to stay the same size, but just move to the center and if some one could tell me how to do that I would appreciate it greatly.

  Read the article

• Resize Debian in VirtualBox

  - by Poni

  I have a VM with one HD of size 3GB and I'd like to enlarge its HD to 7GB. So I execute this command on the host (while guest is shutdown): VBoxManage modifyhd debian.vdi --resize 7168 Then I run the guest, Debian 6, and then: smith@debian6:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 2.8G 2.6G 60M 98% / tmpfs 61M 0 61M 0% /lib/init/rw udev 57M 160K 57M 1% /dev tmpfs 61M 0 61M 0% /dev/shm smith@debian6:~$ sudo parted /dev/sda print Model: ATA VBOX HARDDISK (scsi) Disk /dev/sda: 3221MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 3035MB 3034MB primary ext3 boot 2 3036MB 3220MB 185MB extended 5 3036MB 3220MB 185MB logical linux-swap(v1) smith@debian6:~$ cat /proc/partitions major minor #blocks name 8 0 3145728 sda 8 1 2962432 sda1 8 2 1 sda2 8 5 180224 sda5 So, no automatic resizing (detection) of the HD/partition (while VirtualBox, in the host, shows it's 7GB now). Ok... Then I do: smith@debian6:~$ sudo resize2fs /dev/sda1 resize2fs 1.41.12 (17-May-2010) The filesystem is already 740608 blocks long. Nothing to do! smith@debian6:~$ sudo parted GNU Parted 2.3 Using /dev/sda Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) select /dev/sda1 Using /dev/sda1 (parted) resize WARNING: you are attempting to use parted to operate on (resize) a file system. parted's file system manipulation code is not as robust as what you'll find in dedicated, file-system-specific packages like e2fsprogs. We recommend you use parted only to manipulate partition tables, whenever possible. Support for performing most operations on most types of file systems will be removed in an upcoming release. Partition number? 1 Start? 0 End? [3034MB]? Here I'm stuck. At the above parted it asks me to resize to 3GB. No point in that, right.. What should I do in order to enlarge this partition?

  Read the article

• Why is mkfs overwriting the LUKS encryption header on LVM on RAID partitions on Ubuntu 12.04?

  - by Starchy

  I'm trying to setup a couple of LUKS-encrypted partitions to be mounted after boot-time on a new Ubuntu server which was installed with LVM on top of software RAID. After running cryptsetup luksFormat, the LUKS header is clearly visible on the volume. After running any flavor of mkfs, the header is overwritten (which does not happen on other systems that were setup without LVM), and cryptsetup will no longer recognize the device as a LUKS device. # cryptsetup -y --cipher aes-cbc-essiv:sha256 --key-size 256 luksFormat /dev/dm-1 WARNING! ======== This will overwrite data on /dev/dm-1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: # hexdump -C /dev/dm-1|head -n5 00000000 4c 55 4b 53 ba be 00 01 61 65 73 00 00 00 00 00 |LUKS....aes.....| 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000020 00 00 00 00 00 00 00 00 63 62 63 2d 65 73 73 69 |........cbc-essi| 00000030 76 3a 73 68 61 32 35 36 00 00 00 00 00 00 00 00 |v:sha256........| 00000040 00 00 00 00 00 00 00 00 73 68 61 31 00 00 00 00 |........sha1....| # cryptsetup luksOpen /dev/dm-1 web2-var # mkfs.ext4 /dev/mapper/web2-var [..snip..] Creating journal (32768 blocks): done Writing superblocks and filesystem accounting information: done # hexdump -C /dev/dm-1|head -n5 # cryptsetup luksClose /dev/mapper/web2-var 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00000400 00 40 5d 00 00 88 74 01 66 a0 12 00 17 f2 6d 01 |.@]...t.f.....m.| 00000410 f5 3f 5d 00 00 00 00 00 02 00 00 00 02 00 00 00 |.?].............| 00000420 00 80 00 00 00 80 00 00 00 20 00 00 00 00 00 00 |......... ......| # cryptsetup luksOpen /dev/dm-1 web2-var Device /dev/dm-1 is not a valid LUKS device. I have also tried mkfs.ext2 with the same result. Based on setups I've done successfully on Debian and Ubuntu (but not LVM or Ubuntu 12.04), it's hard to see why this is failing.

  Read the article

• Have an Input/output error when connecting to a server via ssh

  - by Shehzad009

  Hello I seem to be having a problem while connecting to a Ubuntu Server while connecting via ssh. When I login, I get this error. Could not chdir to home directory /home/username: Input/output error It seems like my home folder is corrupt or something. I cannot ls in the home folder directory, and in my usename directory, I can't cd into this. As root I cannot ls in the home directory as well or in any directory in Home. I notice as well when I save in vim or quit, it get this error at the bottom of the page E138: Cannot write viminfo file /home/root/.viminfo! Any ideas? EDIT: this is what happens if I type in these commands mount proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) /dev/mapper/RAID1-lvvar on /var type xfs (rw) /dev/mapper/RAID5-lvsrv on /srv type xfs (rw) /dev/mapper/RAID5-lvhome on /home type xfs (rw) /dev/mapper/RAID1-lvtmp on /tmp type reiserfs (rw) dmesg | tail [1213273.364040] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213274.084081] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213309.364038] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213310.084041] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213345.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213346.084042] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213381.365036] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213382.084047] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213417.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213418.084063] Filesystem "dm-4": xfs_log_force: error 5 returned. fdisk -l /dev/sda Cannot open /dev/sda

  Read the article

• Successful login with iscsiadm on target still doesn't create block device

  - by Halfgaar

  I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

  Read the article

• Why is my filesystem being mounted read-only in linux?

  - by Tim

  I am trying to set up a small linux system based on Gentoo on a VirtualBox machine, as a step towards deploying the same system onto a low-spec Single Board Computer. For some reason, my filesystem is being mounted read-only. In my /etc/fstab, I have: /dev/sda1 / ext3 defaults 0 0 none /proc proc defaults 0 0 none /sys sysfs defaults 0 0 none /dev/shm tmpfs defaults 0 0 However, once booted /proc/mounts shows rootfs / rootfs rw 0 0 /dev/root / ext3 ro,relatime,errors=continue,barrier=0,data=writeback 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 udev /dev tmpfs rw,nosuid,relatime,size=10240k,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620 0 0 none /dev/shm tmpfs rw,relatime 0 0 usbfs /proc/bus/usb usbfs rw,nosuid,noexec,relatime,devgid=85,devmode=664 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 (the above may contain errors: there's no practical way to copy and paste) The partition at /dev/hda1 is clearly being mounted OK, since I can read all the data, but it's not being mounted as described in fstab. How might I go about diagnosing / resolving this? Edit: I can remount with mount -o remount,rw / and it works as expected, except that /proc/mounts reports /dev/root mounted at / rather than /dev/sda1 as I'd expect. If I try to remount with mount -a I get mount: none already mounted or /sys busy mount: according to mtab, sysfs is already mounted on /sys Edit 2: I resolved the problem with mount -a (the same error was occuring during startup, it turned out) by changing the sysfs and proc lines to proc /proc proc [...] sysfs /sys sysfs [...] Now mount -a doesn't complain, but it doesn't result in a read-write root partition. mount -o remount / does cause the root partition to be remounted, however.

  Read the article

• Finding a shared HDD attached to the network from my F-13 machine

  - by Ramy

  Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

  Read the article

• Adding third disk as a single disk in a server with an existing RAID1

  - by slowhandsolo

  I've got a ProLiant DL360 G5 server (Fedora 13) with two SAS disks in a hardware RAID 1, working fine. Now I hot plugged another SAS disk. I'd like to configure this new hard disk out of my RAID, as a single non-RAID disk (ex. /dev/sdb). Even after rebooting the server, I can't see the new disk with "fdisk -l". It displays only my hardware RAID, but not the new disk. [root@myserver]# fdisk -l Disco /dev/cciss/c0d0: 300.0 GB, 299966445568 bytes Disposit. Inicio Comienzo Fin Bloques Id Sistema /dev/cciss/c0d0p1 * 1 126 512000 83 Linux /dev/cciss/c0d0p2 126 71798 292422656 8e Linux LVM Disco /dev/dm-0: 234.9 GB, 234881024000 bytes Disco /dev/dm-1: 10.5 GB, 10536091648 bytes Disco /dev/dm-2: 21.0 GB, 20971520000 bytes Disco /dev/dm-3: 31.5 GB, 31474057216 bytes Disco /dev/dm-4: 1577 MB, 1577058304 bytes However, I can see the new disk using the HP Array Configuration Utility CLI for Linux "hpacucli": [root@myserver]# hpacucli => controller slot=0 physicaldrive all show status physicaldrive 1I:1:1 (port 1I:box 1:bay 1, 300 GB): OK physicaldrive 1I:1:2 (port 1I:box 1:bay 2, 300 GB): OK physicaldrive 1I:1:3 (port 1I:box 1:bay 3, 300 GB): OK => controller slot=0 pd all show detail Smart Array P400i in Slot 0 (Embedded) array A physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 **unassigned** physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: **Unassigned Drive** As you can see, I've got two SAS disks in a RAID 1 and the new disk as "unassigned". Is there any way to work with the new disk as another non-RAID single disk? If relevant, I want to create a new partition in my new disk, format it with mkfs and mount it, but as I can't see it with fdisk, I don't know how to do it. Thanks!

  Read the article

• RHEL Java Application returns "No space left on device" but only 3% used

  - by FiveO

  My Java Application returns following Exception when saving a new file in /opt/wso2 on a CentOS 6.4: Caused by java.io.FileNotFoundException: ... (No space left on device) Caused by: java.io.FileNotFoundException: /opt/wso2/FrameworkFiles/trk_2014062500042488825_TRCK_PatfallHospis_pFromHospis_66601fb3-a03c-4149-93c3-6892e0a10fea.txt (No space left on device) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:212) at java.io.FileOutputStream.<init>(FileOutputStream.java:99) at com.avintis.esb.framework.adapter.wso2.FrameworkAdapterWSO2.sendMessages(FrameworkAdapterWSO2.java:634) ... 23 more But when I run df -a I can see that the partition still has plenty of space available: [root@stzsi466 wso2]# df -a Filesystem 1K-blocks Used Available Use% Mounted on /dev/mapper/vg_stzsi466-lv_root 12054824 2116092 9326380 19% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys devpts 0 0 0 - /dev/pts tmpfs 4030764 0 4030764 0% /dev/shm /dev/sda1 495844 53858 416386 12% /boot /dev/sdb1 51605436 1424288 47559744 3% /opt/wso2 none 0 0 0 - /proc/sys/fs/binfmt_misc [root@stzsi466 ~]# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/mapper/vg_stzsi466-lv_root 765536 45181 720355 6% / tmpfs 1007691 1 1007690 1% /dev/shm /dev/sda1 128016 44 127972 1% /boot /dev/sdb1 3276800 6137 3270663 1% /opt/wso2 What is the problem here? Is it caused by the Java on CentOS 6.4? I have another server running Redhat REHL 6.4 and all works fine - same Java etc. Does anyone know of this problem?

  Read the article

• dd on entire disk, but do not want empty portion

  - by Jonathan Henson

  I have a disk, say /dev/sda. Here is fdisk -l: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0000e4b5 Device Boot Start End Blocks Id System /dev/sda1 * 1 27 209920 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 27 525 4000768 5 Extended Partition 2 does not end on cylinder boundary. /dev/sda5 27 353 2621440 83 Linux /dev/sda6 353 405 416768 83 Linux /dev/sda7 405 490 675840 83 Linux /dev/sda8 490 525 282624 83 Linux I need to make an image to store on our file server for use in flashing other devices we are manufacturing so I only want the used space (only about 4gb). I want to keep the mbr etc... as this device should be boot ready as soon as the copy is finished. Any ideas? I previously had been using dd if=/dev/sda of=[//fileserver/file], but at that time, my master copy was on a 4gb flash ide.

  Read the article

• Fixing damaged partition table

  - by dr4cul4

  This is continuation of Recover Extended Partition , but this time I have different problem related partition table it self. I managed to restore partition that I needed and backed up files that were crucial to me (at least those that I had space to store somewhere) OK now get to the problem. My partition table is corrupted, booting RIP Linux I can mount it in truecrypt (and other ones that recovered), but that's basically it. When I launch GParted I have unallocated drive. GParted Dev info: Device Information Model: ATA ST2000DL003-9VT1 Size: 1.82TiB Path: /dev/sda Partition table: unrecognized Heads: 255 Sectors/track: 63 Cylinders: 243201 Total Sectors: 3907029168 Sector size: 512 When I check information on unallocated space I get: File system: unallocated Size: 1.82TiB First sector: 0 Last sector: 3907029167 Total sectors: 3907029168 Warning: Can't have a partition outside the disk! Now the output of testdisc (Analyze): TestDisk 6.13, Data Recovery Utility, November 2011 Christophe GRENIER <[email protected]> http://www.cgsecurity.org Disk /dev/sda - 2000 GB / 1863 GiB - CHS 243201 255 63 Current partition structure: Partition Start End Size in sectors > 1 P Linux 13132 242 39 16353 233 8 51744768 2 E extended LBA 16807 223 1 243201 254 63 3637021626 No partition is bootable 5 L Linux 16807 223 57 20430 39 25 58191872 X extended 20430 70 1 243201 78 13 3578816632 Invalid NTFS or EXFAT boot 6 L HPFS - NTFS 20430 71 58 243201 78 13 3578816512 6 LNext Now fdisk: # fdisk -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00039cd0 Device Boot Start End Blocks Id System /dev/sda1 210980864 262725631 25872384 83 Linux /dev/sda2 270018504 3907040129 1818510813 f W95 Ext'd (LBA) /dev/sda5 270018560 328210431 29095936 83 Linux /dev/sda6 328212480 3907028991 1789408256 7 HPFS/NTFS/exFAT Now I would like to fix that to arrange partitions correctly, but I have no idea which tool is capable of fixing that (tried, a few, some of them offered fixing, but it was to risky at the moment - still backing up data).

  Read the article

• Assembling Software RAID in Live CD for data recovery

  - by Maletor

  I need help recovering some data that's on my RAID which is on a LVM on my server running Ubuntu. What happened was I deleted the logical volume that controlled my swap space which was on a partition on drives sda2, sdb2, sdc2, and sdd2 in RAID1. This foobared my whole system for one reason or another. Booting leave me with grub rescue and an error saying that it is an unknown filesystem. When I boot to a live cd I can see my RAID arrays and I can even start them up. However, it doesn't appear to mount them anywhere so I can't see the data. I am in the live cd now and I have done sudo apt-get install mdadm lvm2 so it should be mounting them correctly. I just can't see why it wouldn't. Please any help is appreciated here. Here is some output. By the way, there are 3 RAIDs, 1) /boot 100mb RAID1, 2) swap 10gb RAID1, 3) root 990GB RAID5 ubuntu@ubuntu:~$ df -h Filesystem Size Used Avail Use% Mounted on aufs 124M 101M 18M 86% / none 2.0G 324K 2.0G 1% /dev /dev/sde1 2.0G 826M 1.2G 42% /cdrom /dev/loop0 667M 667M 0 100% /rofs none 2.0G 164K 2.0G 1% /dev/shm tmpfs 2.0G 28K 2.0G 1% /tmp none 2.0G 92K 2.0G 1% /var/run none 2.0G 0 2.0G 0% /var/lock none 2.0G 0 2.0G 0% /lib/init/rw /dev/md1 91M 73M 15M 84% /media/5ac3dbf1-a6c5-409c-96ae-edc6e27992c7 ubuntu@ubuntu:~$ cat /etc/fstab aufs / aufs rw 0 0 tmpfs /tmp tmpfs nosuid,nodev 0 0 /dev/sda2 swap swap defaults 0 0 /dev/sdb2 swap swap defaults 0 0 /dev/sdc2 swap swap defaults 0 0 /dev/sdd2 swap swap defaults 0 0

  Read the article

• How to delete removed devices from a mdadm RAID1?

  - by Kabuto

  I had to replace two hard drives in my RAID1. After adding the two new partitions the old ones are still showing up as removed while the new ones are only added as spare. I've had no luck removing the partitions marked as removed. Here's the RAID in question. Note the two devices (0 and 1) with state removed. $ mdadm --detail /dev/md1 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. /dev/md1: Version : 00.90 Creation Time : Thu May 20 12:32:25 2010 Raid Level : raid1 Array Size : 1454645504 (1387.26 GiB 1489.56 GB) Used Dev Size : 1454645504 (1387.26 GiB 1489.56 GB) Raid Devices : 3 Total Devices : 3 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 12 21:30:39 2013 State : clean, degraded Active Devices : 1 Working Devices : 3 Failed Devices : 0 Spare Devices : 2 UUID : 10d7d9be:a8a50b8e:788182fa:2238f1e4 Events : 0.8717546 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 8 34 2 active sync /dev/sdc2 3 8 18 - spare /dev/sdb2 4 8 2 - spare /dev/sda2 How do I get rid of these devices and add the new partitions as active RAID devices? Update I seem to have gotten rid of them. My RAID is resyncing, but the two drives are still marked as spares and are number 3 and 4, which looks wrong. I'll have to wait for the resync to finish. All I did was to fix the metadata error by editing my mdadm.conf and rebooting. I tried rebooting before, but this time it worked for whatever reason. Number Major Minor RaidDevice State 3 8 2 0 spare rebuilding /dev/sda2 4 8 18 1 spare rebuilding /dev/sdb2 2 8 34 2 active sync /dev/sdc2

  Read the article

• Ubuntu 10.04 and fedora 14 grub conflict

  - by sawren

  I tried to triple boot Windows xp, Fedora 14 and Ubuntu 10.04. I first installed Windows xp, then fedora followed by Ubuntu. The problem is that i don't get option to boot Ubuntu while Xp boots fine. It seems Ubuntu was unable to replace Fedora's grub with its own at MBR. Looking at their grub conf file, Fedora and Ubuntu identifies same harddisk as two different devices and i do have another 80 GB harddisk which doesn't have any OS. Below is the details on my partitions and partial information from grub files of both OS. Device Boot Start End Blocks Id System /dev/sda1 * 63 40965749 20482843+ 7 HPFS/NTFS /dev/sda2 102414436 312576704 105081134+ f W95 Ext'd (LBA) /dev/sda3 40965750 102414374 30724312+ 83 Linux - /Home (for fedora) /dev/sda5 102414438 204812684 51199123+ 7 HPFS/NTFS /dev/sda6 204812748 253634219 24410736 83 Linux -- ubuntu /dev/sda7 253634283 302455754 24410736 83 Linux -- fedora /dev/sda8 302455818 312576704 5060443+ 82 Linux swap / Solaris grub.cfg from ubuntu ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 ro quiet splash initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Microsoft Windows XP Professional (on /dev/sdb1)" { insmod ntfs set root='(hd1,1)' search --no-floppy --fs-uuid --set cad48cc6d48cb5eb drivemap -s (hd0) ${root} chainloader +1 } menuentry "Fedora (2.6.35.14-96.fc14.i686) (on /dev/sdb6)" { insmod ext2 set root='(hd1,6)' search --no-floppy --fs-uuid --set 6aee34cf-f77a-489a-9361-85d07194b84b linux /boot/vmlinuz-2.6.35.14-96.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.14-96.fc14.i686.img } menuentry "Fedora (2.6.35.6-45.fc14.i686) (on /dev/sdb6)" { insmod ext2 set root='(hd1,6)' search --no-floppy --fs-uuid --set 6aee34cf-f77a-489a-9361-85d07194b84b linux /boot/vmlinuz-2.6.35.6-45.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.6-45.fc14.i686.img } ### END /etc/grub.d/30_os-prober ### grub.conf from fedora default=0 timeout=5 splashimage=(hd0,5)/boot/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.35.14-96.fc14.i686) root (hd0,5) kernel /boot/vmlinuz-2.6.35.14-96.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.14-96.fc14.i686.img title Fedora (2.6.35.6-45.fc14.i686) root (hd0,5) kernel /boot/vmlinuz-2.6.35.6-45.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.6-45.fc14.i686.img title Other rootnoverify (hd0,0) chainloader +1

  Read the article

• Need help partitioning when reinstalling Ubuntu 14.04

  - by Chris M.

  I upgraded to 14.04 about a month ago on my HP Mini netbook (about 16 GB hard disk). A few days ago the system crashed (I don't know why but I was using internet at the time). When I restarted the computer, Ubuntu would not load. Instead, I got a message from the BIOS saying Reboot and Select proper Boot device or Insert Boot Media in selected Boot device and press a key I took this to mean that I needed to reinstall 14.04. When I try to reinstall Ubuntu from the USB stick, I choose "Erase disk and install Ubuntu" but then I get a message: Some of the partitions you created are too small. Please make the following partitions at least this large: / 3.3 GB If you do not go back to the partitioner and increase the size of these partitions, the installation may fail. At first I hit Continue to see if it would install anyway, and it gave the message: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition # 1 (sda) at / failed. You may resume partitioning from the partitioning menu. The second time I hit Go Back, and it took me to the following partitioning table: Device Type Mount Point Format Size Used System /dev/sda /dev/sda1 ext4 (checked) 3228 MB Unknown /dev/sda5 swap (not checked) 1063 MB Unknown + - Change New Partition Table... Revert Device for boot loader installation: /dev/sda ATA JM Loader 001 (4.3 GB) At this point I'm not sure what to do. I've never partitioned my hard drive before and I don't want to screw things up. (I'm not particularly tech savvy.) Can you instruct me what I should do. (P.S. I'm afraid the table might not appear as I typed it in.) Results from fdisk: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders, total 8388608 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 7860 MB, 7860125696 bytes 155 heads, 31 sectors/track, 3194 cylinders, total 15351808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009a565 Device Boot Start End Blocks Id System /dev/sdb1 * 2768 15351807 7674520 b W95 FAT32 ubuntu@ubuntu:~$ Here is what it displays when I open the Disks utility (I tried the screenshot terminal command you suggested but it didn't seem to do anything): 4.3 GB Hard Disk /dev/sda Model: JM Loader 001 (01000001) Size: 4.3 GB (4,294,967,296 bytes) Serial Number: 01234123412341234 Assessment: SMART is not supported Volumes Size: 4.3 GB (4,294,967,296 bytes) Device: /dev/sda Contents: Unknown (There is a button in the utility that when you click it gives the following options: Format... Create Disk Image... Restore Disk Image... Benchmark but SMART Data & Self-Tests... is dimmed out) When I hit F9 Change Boot Device Order, it shows the hard drive as: SATA:PM-JM Loader 001 When I hit F10 to get me into the BIOS Setup Utility, under Diagnostic it shows: Primary Hard Disk Self Test Not Support NetworkManager Tool State: disconnected Device: eth0 Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 00:26:55:B0:7F:0C Capabilities: Carrier Detect: yes Wired Properties Carrier: off When I run command lshw -C network, I get: WARNING: you should run this program as super-user. *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:16 memory:feafc000-feafffff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: c0 serial: 00:26:55:b0:7f:0c capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:febc0000-febfffff ioport:ec80(size=128) WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• Failure connecting to Dell MD3200i from XenServer 6.2 pool

  - by Tom Sparrow

  This question also asked at Citrix Forums http://forums.citrix.com/thread.jspa?threadID=332289 I have a MD3200i that is currently working fine with my Xen5.6 pool, but I cannot get a connection to the new 6.2 pool to work. I previously had a problem with a 6.0 upgrade (which is why the old pool is still on 5.6), but rolled back rather than fix it as it wasn't urgent at the time. This install is on new machines - I tried 6.1 first (which had the same problems) then 6.2 was released the second day after installation so I switched to that. I've not installed anything from the Dell resource DVD at this point - I can't find anything saying I should, and everything I have read suggests it shouldn't be necessary. I can ping all 8 ip addresses from both servers in the pool, iscsiadm -m discovery works fine, I can login to the nodes and iscsiadm reports the sessions active correctly. I've added the required sections to multipath.conf, but multipath -ll reports DM multipath kernel driver not loaded immediately after boot. The following is a log of a test session immediately after boot. root@xen3 ~]# iscsiadm -m node --loginall=all Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.101,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.101,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.104,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.102,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.103,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.104,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.102,3260] Logging in to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.103,3260] Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.101,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.101,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.104,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.102,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.103,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.104,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.130.102,3260]: successful Login to [iface: default, target: iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91, portal: 192.168.131.103,3260]: successful [root@xen3 ~]# iscsiadm -m session tcp: [1] 192.168.130.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [2] 192.168.131.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [3] 192.168.131.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [4] 192.168.131.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [5] 192.168.130.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [6] 192.168.130.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [7] 192.168.130.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [8] 192.168.131.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 [root@xen3 ~]# service multipathd restart ok Stopping multipathd daemon: [ OK ] Starting multipathd daemon: [ OK ] [root@xen3 ~]# multipath Jul 04 09:58:47 | DM multipath kernel driver not loaded Jul 04 09:58:47 | DM multipath kernel driver not loaded [root@xen3 ~]# multipath -ll Jul 04 09:59:03 | DM multipath kernel driver not loaded Jul 04 09:59:03 | DM multipath kernel driver not loaded [ root@xen3 ~]# modprobe dm_multipath [root@xen3 ~]# multipath Jul 04 10:19:50 | 36b8ca3a0e7024800194a0bd11891cd14: ignoring map create: 1Dell_Internal_Dual_SD_0123456789AB undef Dell,Internal Dual SD size=1.9G features='0' hwhandler='0' wp=undef `-+- policy='round-robin 0' prio=1 status=undef `- 7:0:0:0 sdb 8:16 undef ready running [root@xen3 ~]# multipath -ll 1Dell_Internal_Dual_SD_0123456789AB dm-1 Dell,Internal Dual SD size=1.9G features='0' hwhandler='0' wp=rw `-+- policy='round-robin 0' prio=1 status=enabled `- 7:0:0:0 sdb 8:16 active ready running [root@xen3 ~]# iscsiadm -m session tcp: [1] 192.168.130.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [2] 192.168.131.101:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [3] 192.168.131.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [4] 192.168.131.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [5] 192.168.130.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [6] 192.168.130.104:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [7] 192.168.130.102:3260,2 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 tcp: [8] 192.168.131.103:3260,1 iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 [root@xen3 ~]# dmesg | tail -n 50 [ 1161.881010] sd 8:0:0:0: [sdf] Unhandled error code [ 1161.881013] sd 8:0:0:0: [sdf] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1161.881017] sd 8:0:0:0: [sdf] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1161.881024] end_request: I/O error, dev sdf, sector 0 [ 1161.881031] Buffer I/O error on device sdf, logical block 0 [ 1161.881045] sd 15:0:0:0: [sdi] Unhandled error code [ 1161.881048] sd 15:0:0:0: [sdi] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1161.881052] sd 15:0:0:0: [sdi] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1161.881058] end_request: I/O error, dev sdi, sector 0 [ 1161.881065] Buffer I/O error on device sdi, logical block 0 [ 1161.881122] sd 9:0:0:0: [sdg] Unhandled error code [ 1161.881124] sd 9:0:0:0: [sdg] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1161.881126] sd 9:0:0:0: [sdg] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1161.881132] end_request: I/O error, dev sdg, sector 0 [ 1161.881140] Buffer I/O error on device sdg, logical block 0 [ 1168.220951] connection6:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220957] connection7:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220967] connection7:0: detected conn error (1011) [ 1168.220969] connection4:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220973] connection4:0: detected conn error (1011) [ 1168.220975] connection3:0: ping timeout of 15 secs expired, recv timeout 10, last rx 84060, last ping 85060, now 86560 [ 1168.220978] connection3:0: detected conn error (1011) [ 1168.220985] connection6:0: detected conn error (1011) [ 1168.480994] sd 14:0:0:0: [sde] Unhandled error code [ 1168.480998] sd 14:0:0:0: [sde] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481001] sd 14:0:0:0: [sde] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481009] end_request: I/O error, dev sde, sector 0 [ 1168.481015] Buffer I/O error on device sde, logical block 0 [ 1168.481076] sd 11:0:0:0: [sdc] Unhandled error code [ 1168.481078] sd 11:0:0:0: [sdc] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481080] sd 11:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481087] end_request: I/O error, dev sdc, sector 0 [ 1168.481092] Buffer I/O error on device sdc, logical block 0 [ 1168.481144] sd 10:0:0:0: [sdd] Unhandled error code [ 1168.481147] sd 10:0:0:0: [sdd] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481150] sd 10:0:0:0: [sdd] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481156] end_request: I/O error, dev sdd, sector 0 [ 1168.481163] Buffer I/O error on device sdd, logical block 0 [ 1168.481168] sd 13:0:0:0: [sdj] Unhandled error code [ 1168.481170] sd 13:0:0:0: [sdj] Result: hostbyte=DID_TRANSPORT_DISRUPTED driverbyte=DRIVER_OK [ 1168.481172] sd 13:0:0:0: [sdj] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 1168.481178] end_request: I/O error, dev sdj, sector 0 [ 1168.481184] Buffer I/O error on device sdj, logical block 0 [ 1457.105996] device-mapper: multipath round-robin: version 1.0.0 loaded [ 1457.106155] device-mapper: multipath: Cannot access device path 8:0: -16 [ 1457.106164] device-mapper: table: 252:1: multipath: error getting device [ 1457.106172] device-mapper: ioctl: error adding target to table [ 1457.171292] device-mapper: multipath: Cannot access device path 8:0: -16 [ 1457.171299] device-mapper: table: 252:1: multipath: error getting device [ 1457.171304] device-mapper: ioctl: error adding target to table [root@xen3 ~]# fdisk -l Disk /dev/sda: 299.4 GB, 299439751168 bytes 255 heads, 63 sectors/track, 36404 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 5 40131 de Dell Utility /dev/sda2 * 6 528 4194304 83 Linux Partition 2 does not end on cylinder boundary. /dev/sda3 528 1050 4194304 83 Linux /dev/sda4 1050 36404 283986359+ 8e Linux LVM Disk /dev/sdb: 2040 MB, 2040528896 bytes 255 heads, 63 sectors/track, 248 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 1 248 1992028+ 83 Linux Disk /dev/dm-1: 2040 MB, 2040528896 bytes 255 heads, 63 sectors/track, 248 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/dm-1p1 1 248 1992028+ 83 Linux [root@xen3 ~]# xe sr-probe type=lvmoiscsi device-config:target=192.168.130.101 device-config:targetIQN=iqn.1984-05.com.dell:powervault.md3200i.6782bcb0006bd850000000004ed88b91 Error code: SR_BACKEND_FAILURE_107 Error parameters: , The SCSIid parameter is missing or incorrect, <?xml version="1.0" ?> <iscsi-target/> Note: the xml ends there correctly on the last line - it doesn't ever return a list of LUNs (and there is one in the group on the SAN for those servers.

  Read the article

• Ubuntu server has slow performance

  - by Rich

  I have a custom built Ubuntu 11.04 server with a 6 disk software RAID 10 primary drive. On it I'm primarily running a PostgreSQL and a few other utilities that stream data from the web. I often find after a few hours of uptime the server starts to lag with all kinds of processes. For example, it may take 10-15 seconds after log-in to get a shell prompt. It might take 5-10 seconds for top to come up. An ls might take a second or two. When I look at top there is almost no CPU usage. There's a fair amount of memory used by the PostgreSQL server but not enough to bleed into swap. I have no idea where to go from here, other than to suspect the RAID10 (I've only ever had software RAID 1's before). Edit: Output from top: top - 11:56:03 up 1:46, 3 users, load average: 0.89, 0.73, 0.72 Tasks: 119 total, 1 running, 118 sleeping, 0 stopped, 0 zombie Cpu(s): 0.2%us, 0.0%sy, 0.0%ni, 93.5%id, 6.2%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 16325596k total, 3478248k used, 12847348k free, 20880k buffers Swap: 19534176k total, 0k used, 19534176k free, 3041992k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1747 woodsp 20 0 109m 10m 4888 S 1 0.1 0:42.70 python 357 root 20 0 0 0 0 S 0 0.0 0:00.40 jbd2/sda3-8 1 root 20 0 24324 2284 1344 S 0 0.0 0:00.84 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.24 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 10 root 20 0 0 0 0 S 0 0.0 0:00.02 ksoftirqd/1 12 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/1 13 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/2 14 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/2:0 15 root 20 0 0 0 0 S 0 0.0 0:00.00 ksoftirqd/2 16 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/2 17 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/3 18 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/3:0 19 root 20 0 0 0 0 S 0 0.0 0:00.02 ksoftirqd/3 20 root RT 0 0 0 0 S 0 0.0 0:00.01 watchdog/3 21 root 0 -20 0 0 0 S 0 0.0 0:00.00 cpuset 22 root 0 -20 0 0 0 S 0 0.0 0:00.00 khelper 23 root 20 0 0 0 0 S 0 0.0 0:00.00 kdevtmpfs 24 root 0 -20 0 0 0 S 0 0.0 0:00.00 netns 26 root 20 0 0 0 0 S 0 0.0 0:00.00 sync_supers df -h rpsharp@ncp-skookum:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 1.8T 549G 1.2T 32% / udev 7.8G 4.0K 7.8G 1% /dev tmpfs 3.2G 492K 3.2G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.8G 0 7.8G 0% /run/shm /dev/sda2 952M 128K 952M 1% /boot/efi /dev/md0 5.5T 562G 4.7T 11% /usr/local free -m psharp@ncp-skookum:~$ free -m total used free shared buffers cached Mem: 15942 3409 12533 0 20 2983 -/+ buffers/cache: 405 15537 Swap: 19076 0 19076 tail -50 /var/log/syslog Jul 3 06:31:32 ncp-skookum rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="1070" x-info="http://www.rsyslog.com"] rsyslogd was HUPed Jul 3 06:39:01 ncp-skookum CRON[14211]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 06:40:01 ncp-skookum CRON[14223]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 07:00:01 ncp-skookum CRON[14328]: (woodsp) CMD (/home/woodsp/bin/mail_tweetupdate # email an update) Jul 3 07:00:01 ncp-skookum CRON[14327]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 07:00:28 ncp-skookum sendmail[14356]: q63E0SoZ014356: from=woodsp, size=2328, class=0, nrcpts=2, msgid=<[email protected]>, relay=woodsp@localhost Jul 3 07:00:29 ncp-skookum sm-mta[14357]: q63E0Si6014357: from=<[email protected]>, size=2569, class=0, nrcpts=2, msgid=<[email protected]>, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Jul 3 07:00:29 ncp-skookum sendmail[14356]: q63E0SoZ014356: to=Spencer Wood <[email protected]>,Martin Lacayo <[email protected]>, ctladdr=woodsp (1004/1005), delay=00:00:01, xdelay=00:00:01, mailer=relay, pri=62328, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (q63E0Si6014357 Message accepted for delivery) Jul 3 07:00:29 ncp-skookum sm-mta[14359]: STARTTLS=client, relay=mx3.stanford.edu., version=TLSv1/SSLv3, verify=FAIL, cipher=DHE-RSA-AES256-SHA, bits=256/256 Jul 3 07:00:29 ncp-skookum sm-mta[14359]: q63E0Si6014357: to=<[email protected]>,<[email protected]>, ctladdr=<[email protected]> (1004/1005), delay=00:00:01, xdelay=00:00:00, mailer=esmtp, pri=152569, relay=mx3.stanford.edu. [171.67.219.73], dsn=2.0.0, stat=Sent (Ok: queued as 8F3505802AC) Jul 3 07:09:08 ncp-skookum CRON[14396]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 07:17:01 ncp-skookum CRON[14438]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jul 3 07:20:01 ncp-skookum CRON[14453]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 07:39:01 ncp-skookum CRON[14551]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 07:40:01 ncp-skookum CRON[14562]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 08:00:01 ncp-skookum CRON[14668]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 08:09:01 ncp-skookum CRON[14724]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 08:17:01 ncp-skookum CRON[14766]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Jul 3 08:20:01 ncp-skookum CRON[14781]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jul 3 08:39:01 ncp-skookum CRON[14881]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) Jul 3 08:40:01 ncp-skookum CRON[14892]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Output of hdparm -t /dev/sd{a,b,c,d,e,f} This looks suspicious? /dev/sda: Timing buffered disk reads: 2 MB in 4.84 seconds = 423.39 kB/sec /dev/sdb: Timing buffered disk reads: 420 MB in 3.01 seconds = 139.74 MB/sec /dev/sdc: Timing buffered disk reads: 390 MB in 3.00 seconds = 129.87 MB/sec /dev/sdd: Timing buffered disk reads: 416 MB in 3.00 seconds = 138.51 MB/sec /dev/sde: Timing buffered disk reads: 422 MB in 3.00 seconds = 140.50 MB/sec /dev/sdf: Timing buffered disk reads: 416 MB in 3.01 seconds = 138.26 MB/sec

  Read the article

• GRE keepalive with Linux and RouterOS

  - by eri

  I have a Linux host and couple of routerboadrs. I created a GRE tunnel, but Linux does not answer keepalive packages. Then router mark gre connection as unreachable, so I cant send to Linux host from router subnet. If linux sends something into tunnel (ping, etc.) - RouterOS mark connection as reacheble. Second and next packages routed nicely until one minute idle (no traffic). Tunnel in linux a make in this way: remote=x.x.x.x dev=gre21 network=10.21.0.0/16 ip tunnel add ${dev} mode gre remote ${remote} ttl 255 ip addr add 172.16.1.1/24 peer 172.16.1.21 dev ${dev} ip link set ${dev} up ip route add ${network} dev ${dev} And ip l: 14: gre21: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN link/gre 0.0.0.0 peer 109.60.170.15 How to set state "running"? How to keep alive tunnel? Ping in cron?

  Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85  | Next Page >