Search Results

Search found 2066 results on 83 pages for 'cable'.

Page 79/83 | < Previous Page | 75 76 77 78 79 80 81 82 83  | Next Page >

• ASA and cisco vs NSA sonic firewall

  - by Lbaker101

  Currently I’m trying to structure our network to fully support and be redundant with BGP/Multi homing. Our current company size is 40 employees but the major part of that is our Development department. We are a software company and continued connection to the internet is a requirement as 90% of work stops when the net goes down. The only thing hosted on site (that needs to remain up) is our exchange server. Right now i'm faced with 2 different directions and was wondering if I could get your opinions on this. We will have 2 ISPs that are both 20meg up/down and dedicated fiber (so 40megs combined). This is handed off as an Ethernet cable into our server room. ISP#1 first digital ISP#2 CenturyLink we currently have 2x ASA5505s but the 2nd one is not in use. It was there to be a failover and it just needs the security+ license to be matched with the primary device. But this depends on the network structure. I have been looking into the hardware that would be required to be fully redundant and I found that we will either of the following. 2x Cisco 2921+ series routers with failover licenses. They will go in front of the ASAs and either connects in a failover state or 1 ISP into each of the 2921 series routers and then 1 line into each of the ASAs (thus all 4 hardware components will be used actively). So 2x Cisco 2921+ series routers 2x Cisco ASA5505 firewalls The other route 2x SonicWalls NSA2400MX series. 1 primary and the secondary will be in a failover state. This will remove the ASAs from the network and be about 2k cheaper than the cisco route. This also brings down the points of failure because it’s just the 2x sonicwalls It will also allow us to scale all the way up to 200-400 users (depending on their configuration). This also makes so the Sonic walls. So the real question is with the added functionality ect of the sonicwall is there a point in paying so much more to stay the cisco route? Thanks!

  Read the article

• Why does unpartitioned Hitachi HDS5C3020 drive start consuming 50% more power 15 minutes after boot?

  - by Pro Backup

  In a Debian 6.0.6 system there are 74 pieces of 2TB Toshiba DT01ABA200 drives. These drives are identified as Hitachi HDS5C3020BLE630 drives running firmware revision MZ4OAAB0. 64 Drives attached via HP SAS expander cards to an LSI 2008 SAS controller, another 5 drives are connected directly to the mainboard, 4 drives are connected to a Sil based PCI controller and last 1 drive is only powered and has no data cable connected. The controller LSI and Sil card's their onboard BIOS are both disabled and the mpt2sas and sata_sil modules are removed from the Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux kernel. The mpt2sas module is loaded after boot using a modprobe command in /etc/rc.local. These 74 drives are not partitioned, neither formatted and also not mounted. The system consumes: with 0 drives: 70.6 - 70.9 Watt (also 15 minutes after boot); with 74 drives: 330 - 360 Watt, just after boot (is equivalent to 3.5 - 3.9W per drive in idle state); with 74 drives: 420 - 466 Watt, each time in the 15th minute of uptime (is equivalent to 4.7 - 5.3W per drive in idle state). The drive specification lists 4.7W as read/write, and 3.3W as idle power consumption. The increased power consumption is most likely on the 5V line, because after roughly 1 minute an "over current protection" (OCP) of the power supply (PSU) shuts down the power. The used PSU is a single rail model with an OCP of 122A on the 12V line and 55A on the 5V line. Regression: It doesn't matter whether the drive its APM value is set to disabled or 1 (maximum power saving). The operating system records no read/write activity in /proc/diskstats. The values there are identical (28 read, 0 write operations) as immediately after the modprobe operation. Can't test what happens when booting into the mainboard it's BIOS - to exclude any OS intervention - because the Super Micro X8SI6-F mainboard running firmware 06/27/12 has a bug that incorrectly reads a +74.0 C CPU sensor temperature as "High" in BIOS mode, and shuts down the power after 1 minute. What might be causing the drive read/write activity on all drives in the 15th minute after boot and how to prevent it from happening?

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

  Read the article

• XP shared folders not accessible after BIOS changed

  - by stijn

  Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

  Read the article

• Possible capacitor plague - need help identifying

  - by cornjuliox

  I've been having some PC power issues lately, and I think I've tracked it down to a bad power supply. Lately, when I'm on my PC it will often restart without warning, displaying "Hypertransport sync flood error occurred last boot." once POST finishes. I've googled the error, but can't come to a definitive conclusion as to what's causing it. I've seen posts suggesting that it might be a power supply issue, but nothing conclusive. Here's what I've done so far: -I haven't installed anything suspect within the last 3 months. -I do overclock just a tiny bit, so I tried raising the voltages a little. That didn't work so I brought both CPU multiplier and voltages all back to their default settings, but that didn't solve the problem either. The problem still occurs. -AV scanned the whole system, nothing suspect. -I suspected that it might be a bad power supply so I cracked that open and found the following: I think it might be cap plague, but I'm not sure. It looks more like glue TBH. Could someone help me figure out what might be wrong with this PC? EDIT: Sometimes, after these restarts, I noticed that the GPU fan doesn't spin up, and the single rear case fan that just happens to be connected to the same molex Y-cable as the GFX card doesn't spin up either. Anything to that? EDIT 2: I do use the system quite heavily, but I don't know how that will factor into this. I often play Diablo 3 and EVE Online at the same time, frequently alt-tabbing between the two. I also have Firefox open in the background, sometimes with several tabs, and if I feel like it, I'll mute the in-game sound and open foobar2000 for better music. Could it be that I'm just pushing this thing too hard? EDIT 3: I also noticed something odd. Right before I experience these restarts, my monitor would suffer from very faint lines of static moving across the screen. The monitor is still very much useable, but it is very annoying. Following the restart it disappears, and then would gradually re-appear over the next few days, and then restarts again. I find it to be very odd. System specs for good measure: Orion 600 W PSU AMD Athlon II X3 440 (overclocked to 3.14 ghZ, raised the CPU multiplier to x13 from x10) MSI G40-775 motherboard 1 GB inno3D GTX 550 ti 4 GB DDR3 RAM 500 GB Samsung SATA HD

  Read the article

• Default Critique branch office setup: VPNTunnel->HQ, subnets for VOIP/PC, + several Q's

  - by CHickenTaragon

  We're setting up a new branch office. * ~10 users. * Each user has a VOIP phone provided by a hosted solution. * Users need access to resources on HQ (located in another state), so setting up VPN tunnel * HQ only supports certain Cisco/Juniper devices. VOIP provider only supports SonicWall, so current plan is to have two routers w/ separate subnets for VOIP vs. PC traffic. * PC's will plug into pass-thru Ethernet jacks on the VOIP phones, but the phones vs. PC's will point to different subnets. * Cable Modem is 50Mbps / 5Mbps DOCSIS 3.0 business line w/ 5 static IP's. * Each of the 2 subnets will map to one of the 5 public IP's. * May or may not also need to support a VPN tunnel with a second branch office because of a file server they have there that some in the new office use. I'm pushing to have them move the files to a server on the HQ's network so we don't have to worry about setting up an additional tunnel. Questions: Do you foresee any issues with the below set-up? Router recommendations by HQ IT staff: Cisco Router 2811, or Juniper SSG5 or SSG20. Any recommendations about these routers? We need Wi-Fi too – looks like the above routers have models that support this, any reason not to use this? Users need to be able to work from home. If so, how is authentication handled? Right now we use AD credentials for the HQ's domain, but we currently don't plan to have an AD system in the new location since it's only 10 users. We can't tie the authentication system from the new location's router to the AD system of the HQ. All the PC's that will be in the new location are currently in the existing office that is closing down, and are already joined to the domain of the HQ. Please confirm: this + the VPN tunnel will be sufficient for them to connect to authenticated resources on the HQ's network from the new location, correct? Mainly SQL servers and file servers, and a few remote desktop sessions. I'm sure I'll have some more questions, but can't think of them right now.

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• Why doesn't video run smoothly on my laptop anymore?

  - by andygrunt

  This might be an impossible question to answer remotely but I figure there may be some common causes that people can suggest so I think it's worth asking... Video no longer plays smoothly on my laptop. It used to but not for a while now. For example, playing a video on YouTube is pretty typical: I press play (making sure it's not on HD or even HQ) and the video buffers a little then starts to play. At first it plays fine then the video starts to stutter, turning into a slideshow while the sound continues to play smoothly. If I try playing the same video on my Playstation 3 (which is linked to the same network) it plays smoothly so it can't be the connection. Another example is streaming DivX videos. Again, I wait while it buffers and it starts but very soon, instead of a slideshow, this time the video just plays slowly while the sound continues as normal (instantly getting out of sync). Even if I let the video fully load before pressing play (i.e. it's no longer streaming), it still behaves the same way. I can even let it load 100% then save the file to hard disk and use VLC player to view it, and the same thing happens. I'm using an old laptop running Windows XP. For the past several years it's been connected to the router via Wi-Fi but in the past few days I've changed that to a network cable (like my PS3) but that hasn't helped. Yes, I regularly install various bits and pieces of software but nothing that I can identify as being the cause. So, are there known causes of this sort of behaviour and if so, what can I do to fix it? Thanks. Update to answer a few questions... Laptop Spec' (note: video has played back fine for the majority of time I've had the laptop) Toshiba Satellite 1900-603 (possibly called something else outside the UK) Intel Pentium 4 2.2 Ghz Processor Originally had 512Mb memory but recently doubled that to 1 Gig of memory Graphics: ATI Mobility Radeon 16Mb DDR VRAM Windows XP SP3 (Home edition) Over the years I've done several things to speed it up (disabling indexing etc) and am generally happy with the performance. I also regularly have a clear out of old software (if for no other reason than the laptop only has a 40Gb hard disk) and use CCleaner and Glary Utilities to strip out much of the crap from my system. Also recently (after doubling the memory), I've tried a few new things which might be likely candidates for slowing the video down such as Rocketdock, Jingle keyboard (which gives an old style 'clacky' typewriter sound when I type - love it), SugarSync, Taskbar Shuffle. However, the video doesn't play smoothly even when I try quit all these apps.

  Read the article

• Very slow printing from print server

  - by evolvd

  Print server is a VM on Xen The VM is Windows 2003 32bit. During the issue the VM is not being taxed in anyway, cpu, memory, hd read/write, and network speed is all good. The problem that I see is the transfer of the print file from the print server to the printer. The 80Mb file is transferred from the client to the print server in about 2 minutes but then it takes about 2 hours for that file to be sent to the printer. I can't figure out why this would just start to happen. The printer is rebooted every evening and is just used for one large print job in the morning. The server has been rebooted with no effect I changed the spool option to send the entire spool to the server before printing starts and it had no effect. This printer problem did happen to come about after some changes to the Xen environment. The Xen servers changed from using HBA NIC cards to software iscsi and a new switch was put in. I don't think this is related to the problem since all the speeds on the VMs are better now. The changed happened on Saturday and the first print to this printer happened on Monday morning. I'm just putting that out there but like I said I don't think it is related but I don't want to rule it out. At this point I don't have many other options besides the physical layer. I can switch out network cable that goes to the printer and I might be able to print the same job to another printer. I wont be able to test those things out till this afternoon though. Any other ideas or test I could do to try to find the reason for the slow speed? I forgot to say that this is only happening when printing to this one printer. ===Update=== I found out that there are a few printers that currently have this issue, not just the one. There are over 30 printers on the server though so I know it's not happening to all of them. I printed a large pdf doc from the server and it was able to print at the normal speed. If the machine sends the large print request it gets to the server fine but then slow to get from the server to the printer. If sent directly from the printer it gets to the printer at the normal speed. The question now is why is there a speed difference when it comes from the machine and why would it start now?

  Read the article

• Win-XP Browsers Hang on page load - (waiting for...)

  - by CHarmon

  Hello, I’m having problems with my browsers hanging on loading pages on my desktop machine. I’m using Windows XP Pro with SP3 and fully updated except for IE 8. All three of my browsers, IE 7, Chrome and Firefox are having the same problems. Pages are not being loaded and are hanging on “waiting for …”. The browsers are waiting for the page being loaded or ad servers. Sometimes a page will load but the loading graphic continues to be displayed as if the page were still loading when the page appears to be fully loaded. The problem is bad enough that I can’t really use any of my browsers. I can eventually get most pages to load by stopping and restarting the page load. I have DSL modem with a wireless router and I have been able to eliminate the modem and router from being the source of my problem. My laptop doesn’t have any problems even when hardwired to the router and with the wireless connection disabled. I deleted the NIC and let XP re-install. Also tried a different network cable. Tried the same router port used in the laptop test. One clue that may be important is that I can’t connect to my router using the desktop machine…the page hangs while trying to connect. I can ping the router and I can quickly connect to the router using the laptop. I also can’t use the Windows update process – the page never fully loads. The problem affects other user accounts and even happens in safe mode. I am convinced the problem is with part of the O/S…some layer able to affect all of the browsers. The purpose of this post is to see if anyone has some ideas before I do a XP repair. I have done quite a bit of trouble-shooting: Ran a full anti-virus scan with AVG – no problems. Ran full scans with Spybot, MalwareBytes and Sophos anti-rootkit – no problems. Ran Chkdsk with both options checked. Ran Disk Clean up Defragged RE-installed IE7 Cleared all the browser caches Ran Ccleaner (registry tool) Ran HijackThis – nothing unusual (problem happens in safe mode too) Ran Process Explorer – no unusual processes Used System Restore and fell back several days – no change in the problem Booted to last known good configuration – no change in the problem Ran MicrosoftFixit50199.msi – no change in the problem Any ideas or suggestions would be appreciated…I’m not looking forward to doing a repair on XP. Thanks in advance for any help.

  Read the article

• Port forwarding not working properly

  - by sudo work

  I'm trying to host a small web server from my home network; however, I have not been able to successfully port forward ports to the local server. My current network topology looks like this: Cable Modem/Router - Secondary Wireless Router - Many computers (including server) The modem/router I'm using is a Cisco (Scientific Atlantic) DPC2100, provided by my ISP. The wireless router that I'm using as the central hub to my home network is a Linksys E3000. The computer being used as a server is running Ubuntu 10.04 Server Edition. The main issue is that I can't access the server remotely, using my WAN IP address. I have port forwarded my wireless router; however, I believe that I need to somehow set my modem to bridge mode. As far as I can tell though, this isn't possible. Here are the various IP address settings: DPC2100 WAN: 69.xxx.xxx.xxx Internal IP: 192.168.100.1 Internal Network: 192.168.7.0 E3000 IP Address: 192.168.7.2 Gateway: 192.168.7.1 Internal IP: 192.168.1.1 Internal Network: 192.168.1.0 Server IP Address: 192.168.1.123 Gateway: 192.168.1.1 Now I can do an nmap at various nodes, and here are the results (from the server): nmap localhost: 22,25,53,80,110,139,143,445,631,993,995,3306,5432,8080 open nmap 192.168.7.2: 22,25,80 (filtered),110,139,445 open (ports I have forwarded in the E3000)* nmap 69.xxx.xxx.xxx: 1720 open *For some reason, I can SSH into the server at 192.168.7.2, but not view the website. Here are also some other settings: /etc/hosts/ 127.0.0.1 localhost 127.0.1.1 servername ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters /etc/apache2/sites-available/default snippet <VirtualHost *:80> DocumentRoot /srv/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> ... </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> ... </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> ... </Directory> </VirtualHost> Let me know if you need any other information; some stuff probably slipped my mind.

  Read the article

• My network drive disappears from Mac OS Finder

  - by Mariusz

  I have recently bought a Netgear WNDR3800 router to use it in my home network. But just the same day I installed it, I noticed a strange behaviour of Finder and iTunes. Let me explain it further. There is a Synology DS111 NAS attached to that router and two Macs with Mac OS X Lion. One of them is connected by a cable and the second one wirelessly. Before I changed my router to the new one I mentioned above, Finder always used to display my NAS on its sidebar. So I could just click its network name to access shared folders existing on it. But after I installed WNDR3800, I can no longer access the NAS that way. It is no longer displayed. I always have to mount it manually by typing its IP address using the Finder's 'connect to server' option. The same NAS supports TimeMachine backups and has an inbuilt DLNA server. And the same situation here. I can't perform a backup because my NAS is no longer accessible in TimeMachine preferences. iTunes does not display it as well (as a multimedia server) even though it used to before I installed that router. What's important, everything works fine for a couple of minutes after I restart the router or the NAS. Or even when I change the NAS's IP address it becomes accessible again in Finder, TimeMachine and iTunes, but only for some time. Both the Mac computers I mentioned behave the same way. And all those issues have been taking place sice I installed that new router. Before I did that, everything had worked fine. My old router was Netgear WGR614v10. Would you be so kind to tell me what you think could possibly be the reason of that behaviour? What settings of the router should I look closer at? I'm not a network specialist, but is it possible that some network packets are blocked for some reason? I will be grateful for any clues you give me. Thank you.

  Read the article

• Linux bonded Interfaces hanging periodically

  - by David

  I've several hosts that are showing problems with connectivity. When working from the command line, for example, typing is frozen for a second or so, then recovers - then it does it again. The most egregious example host would freeze (input) for 15-30 seconds, then recover and go out 5 seconds later. Switching cables didn't do anything - but removing one of the physical cables caused everything to clear up instantly (which why I think this is a network problem). Looking at the network I couldn't see any packets floating that would explain this. These ethernet interfaces (Gigabit Dell) were working normally previously, but since we moved the systems - and put them on a new set of switches - this has been a problem on multiple theoretically identically-configured hosts. The original switches were an HP Procurve 1810-24G and an HP Procurve 1800-24G connected with LLDP; the new switches are both Cisco SG 200-26, which I understand are rebranded Linksys switches. Is this caused by a problem with the switches? Is it the switch configurations? Are the Cisco switches incapable of handling this? I don't see where the configuration is located; I searched the usual /etc/sysconfig/network/devices but there's nothing in there about options (like mii polling) and nothing about the method of balancing the two. Searching scripts, I can't find anything in /etc/init.d/network either. The hosts are almost all Red Hat Enterprise Linux 5.x systems (5.6, 5.7) but some are Ubuntu Server 10.04.3 Lucid Lynx. I need help with both if it comes to that. UPDATE: We're also seeing some problems with servers on the original switches. The HP switches and the Cisco switches are also interconnected (temporarily); there is a cable run from one switch to the next. Pings on any of these hosts show about one ICMP packet out of every 5-6 getting dropped (timed out). Could there be an interaction between the two switches? Oh, and the hosts are using bonding with Balance-RR as the method.

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

• Be your own cloud [closed]

  - by Jedi

  I have reasonably many electronic gadgets that can go LAN or WI-FI. But how do you share and/or syncronize all your files among them? Well, between my laptops and my desktop I use Dropbox. A nice way to share files among computers. But what if your HDD on your laptop is not large enough to carry music, pictures and films. Normally you would buy an extern USB HDD and store them there, but then you cannot reach the files from other computers which are not connected to the USB device. Many would say I should use a solution like a cloud with a disc station or something like that. But my needs are follows: A mass storage which can be reached among devices (laptops, desktops, iPhone, Android phone, XBox or Playstation). Has low power requirements and is silent. Can be reached inside home and it would be nice if it could be reached outside home as well. Cheap I have looked around and I have found an wireless router which can share a USB device: D-Link Wireless N HD Media Router. I thought it would be an interesting solution for a simple local cloud solution. D-Link uses a little program called SharePort Plus which mount the USB device to your computer. Unfortunately is the transfer rate to the USB storage device rather disappointing. The transfer rate was 5.8 Mbps even though the distance between the laptop and the router was 2 meter. The same is happening when I use cable from the computer to the router. Another thing is that SharePort Plus only allows one computer be connected to the device at a time. The last thing was something I could live with. I have search on the Internet for other solutions and found this video from Synology. I'm not sure if their solution is the right one. I think a disc station connected to my home LAN could the right solution. What have you done in your home to store and share files among your computers and game consoles?

  Read the article

• Can not get sound over hdmi in kubuntu 9.10

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

  Read the article

• PC will POST whenever feels likes it

  - by kyrpas

  I'm really sick of my PC and I'd love to throw it off the 5th floor but unfortunately I don't have this luxury right now. The issues started when I moved to a new house about 2 months ago. I didn't have this problem before. Case: Arctic Cooling Silentium T1 with embedded Fusion 550 Eco 80 PSU. M/B: ASRock A790GMH/128M Gfx: ATI Radeon HD 5770 Here's what's happening almost on a daily basis: I wake up in the morning, switch on the PC and all the fans start spinning. 9/10 the graphics fan stays on 100% and I know it won't post. If I'm lucky, ATI's fan stays on full power for a second, then goes back to normal and I get a normal post but that doesn't happen often. No, instead it's just drives me crazy. When I get no POST I'm trying a lot of different things and what bothers me the most is that they all work. But not always. No... That way I could find out what the hell is going on and we don't want that.. right? So, sometimes it manages to POST if I: remove the keyboard remove the power cable for a few minutes remove the graphics card remove the HDD cables do nothing, just turn it on and off a few times Sometimes it doesn't POST even if I do all of the above. And I end up removing all power cables from the M/B, and connecting all the stuff one by one. Sometimes it works, sometimes it doesn't and I just have to pray and wait. What the hell is that? I'm getting pissed of again just thinking about it. The only solution is to leave it on 24/7 but I don't want to do that. It should be able to turn on and off when I press the power button. I'm not asking much. I'm starting to think there's some weird electricity/power issue but I really don't understand what it is. There's no logical explanation about it. At least I can't find one. Any ideas?

  Read the article

• How to configure sendmail to relay through a specific server

  - by ErebusBat

  I have a tiny home server setup behind my cable modem (bresnan communications). I want to be able for this box to send out email (not receive) for notifications and whatnot. What I have already done: I have installed and configured sendmail. I have added mail.bresnan.net as my SMART_HOST directive. What I belive the problem is When I attempt to send an email I get the following in my mail log: Dec 22 10:24:17 batcave sendmail[1530]: oBMHOHrs001530: from=aburns, size=140, class=0, nrcpts=1, msgid=<[email protected]>, relay=aburns@localhost Dec 22 10:24:17 batcave sm-mta[1531]: oBMHOHWZ001531: from=<[email protected]>, size=397, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA-v4, relay=localhost [127.0.0.1] Dec 22 10:24:17 batcave sendmail[1530]: oBMHOHrs001530: to=<[email protected]>, ctladdr=aburns (1000/1000), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30140, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (oBMHOHWZ001531 Message accepted for delivery) Dec 22 10:24:18 batcave sm-mta[1517]: oBMH9mVv001357: to=<[email protected]>, ctladdr=<[email protected]> (1000/1000), delay=00:14:30, xdelay=00:00:42, mailer=relay, pri=300339, relay=pmx0.bresnan.net. [69.145.248.1], dsn=4.0.0, stat=Deferred: Connection timed out with pmx0.bresnan.net. You can see where the message is accepted for delivery by my sendmail server, then where it attempts to hand off to bresnan's server and it timesout. This is where my question is. Asstute readers will notice that pmx0.bresnan.net is not what I have my SMART_HOST directive set as. This is the (outside?) MX server for the bresnan.com/net domain. Apparently bresnan has their network configured so that you can not access this server from within their own network and instead must use the mail.bresnan.net server (which I can connect to). The problem is that I don't know how to tell sendmail to use this server and not the domain. What I have tried Setting a hosts entry so that the pmx0 server points to the mail IP address. This doesn't work, which makes sense as sendmail is obviously doing an MX query to find the server which returns the IP so there is never a need to do a 'normal' DNS resolve so the hosts file never gets involved.

  Read the article

• What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

  - by Tyler

  Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

  Read the article

• Mouse Error Code 24. Windows 7

  - by Cj.

  I've had the same mouse for a while, and it's been working fine until one day, it started giving me a message about a device not working properly. I tried updating the drivers, and re-installing, I even deleted old drivers in case my computer should be a little confused. It never made a difference, and my mouse seemed to be working just fine despite getting the permanent error in my device manager, I looked it up several times online, but I never found anything I could actually use, when I go to official websites, I always get the same response "plug in so so into a different place - drivers - install silverlight before you can watch this tutorial, try it on a different machine". so I gave up on that. But now is where I have a real problem, lately, my little strange error evolved into a fullblown Error 24, and my mouse is starting to turn on and off randomely, especially when it is being used, but I do hear it go "badum..dadum" when I'm off doing something else. when I looked up error code 24, I really didn't find much other than it meaning: Code 24 This device is not present, is not working properly, or does not have all its drivers installed. (Code 24) Cause The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed. Devices stay in this state if they have been prepared for removal. After you remove the device, this error disappears. But, I have tried uninstalling the device entirely several times, and it'll go right back to its previous state with error 24, and turning on and off randomely. what do I do? I cannot afford taking it to a repair place, I can't really afford a new mouse either, I refuse to buy cheap ones as I am a gamer, in need of more than 3 buttons, and a good grip is important. Could there possibly be some confusion in the registry? I do remember having gotten some early problems after I converted my vista to windows7. But I hardly dare going in there unless I'm 100% certain of what I'm going for, and I can honestly say I am at a loss here. Edit: it is a USB mouse we're talking about here. MX™518 Optical Gaming Mouse (logitech) Edit2: I am seeing no rupture, so it must be on the inside of my mouse, or inside the rubber, protecting the cable, that would be really inconvenient to search for

  Read the article

• netbook intel GMA 3150 external monitor 1920x1080 flicker problem

  - by seyenne

  Dear all, i recently purchased a acer netbook (apsire one d260). It runs flawlessly. Yesterday I bought a samsung 23" TFT with a native resolution of 1920x1080. According to the information found in the internet and my local computer dealer, the intel chipset can handle the native resolution of the monitor. However, this is only partly the case. I use the VGA cabel to connect, the monitor instantly switches to the native resolution and now the problem: Occasionaly, especially the first 2 hours after booting up, I have a flickering all over the screen, sometimes the entire screen is shaking and spinning around like crazy. I figured out, that lowering the resolution avoids the flicker but this helps only for some time. I can rule out that it's the monitor's problem since I found no issues with another notebook. Right now, I have no problems with the netbook, for about 30 minutes I didn't experience any issues... But I don't know for how long, it occurs without warning :-) I'm worried that if I would bring the netbook back to the dealer and explain my problem, after testing it on an external screen in the local shop, everything works just fine... And I won't get helped with the problem because I can't prove it. (I'm currently in Thailand and over here, customer service is nothing like back home in Germany) What can I do? Is this a driver related issue? (I installed the latest GPU driver) Is it because of the VGA cable? (But why does it work sometimes without any problems and with no issues on the other notebook) I monitored the GPU/CPU temperature, nothing changes really over time..Can it simply be a faulty GPU and is a replacement justifiable? I'm really stressed now because for the time I'm writing, the flickering didn't occur...but for sure, soon or later it will happen again.. I Forgot to mention, the problem also happens if the netbook runs on battery, unplugged. So the only hardware that is plugged is the TFT screen. ...........and here it comes again, flickering has just begun. NEED HELP! Thank you all for reading through this and giving any suggestions if possible. Cheers

  Read the article

• QNAP (469L) with Debian: can't connect to router

  - by agtoever

  I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

  Read the article

• Can't install .NET framework 4.0 on Windows XP professional version 2002 SP3 (OS bug?)

  - by that guy

  .NET framework 4.0 install fails on Windows XP professional version 2002 SP3: I tried to run setup using "run as..." to make sure the admin rights are used ("protect my computer..." tick was deselected of course). I tried everything: installing using online/offline setup, windows update. install goes a little and then "rolls back" and says: Installation did not succeed .NET Framework 4 has not been installed because: Fatal error during installation. for more information about this problem, see the log file. the full log: http://pastebay.net/1433771 Any ideas? EDIT1: I have found this in the log: "BlockIf: You must install the 32-bit Windows Imaging Component (WIC) before you run Setup. Please visit the Microsoft Download Center to install WIC, and then rerun Setup...." So I found it, and launched "wic_x86_enu.exe" - but it said: WIC Setup error Newer version of update is already on the system. I have already installed: .NET framewrok 2.0 SP2 .NET framewrok 3.0 SP2 .NET framewrok 3.5 SP1 but I need 4.0 . EDIT2: another attempt and it's log. (this time better copy of log file): http://pastebin.com/gmGfbM9a (copy to notepad and save as .htm and open with internet browser). I have tried all the solutions I could find - and nothing helped. I have found something weird: when I formatted the hard drive and installed windows xp again - the .NET framework 4.0 installed ok, but when I plugged my 100Mbit internet cable - the operating system kind off "locked itself" and the bug returned - I could no longer install .NET framework 4.0 again. There was no reason for that to happen, for example I have windows server 2003 in local network, but I don't have active directory enabled on it or anything like that - the server just has some folders shared and thats all (all server's "features" are default). I had the second pc with the same problem - with XP on it too. This seems like the bug of Operating System to me. I couldn't find what was causing the problem. After many days I gave up: backuped everything, formatted HDD and installed Windows 7 professional 64bit. .NET framework 4.0 installed with no problem on it.

  Read the article

• Linux software RAID6: 3 drives offline - how to force online?

  - by Ole Tange

  This is similar to 3 drives fell out of Raid6 mdadm - rebuilding? except that it is not due to a failing cable. Instead the 3rd drive fell offline during rebuild of another drive. The drive failed with: kernel: end_request: I/O error, dev sdc, sector 293732432 kernel: md/raid:md0: read error not correctable (sector 293734224 on sdc). After rebooting both these sectors and the sectors around them are fine. This leads me to believe the error is intermittent and thus the device simply took too long to error correct the sector and remap it. I expect that no data was written to the RAID after it failed. Therefore I hope that if I can kick the last failing device online that the RAID is fine and that the xfs_filesystem is OK, maybe with a few missing recent files. Taking a backup of the disks in the RAID takes 24 hours, so I would prefer that the solution works the first time. I have therefore set up a test scenario: export PRE=3 parallel dd if=/dev/zero of=/tmp/raid${PRE}{} bs=1k count=1000k ::: 1 2 3 4 5 parallel mknod /dev/loop${PRE}{} b 7 ${PRE}{} \; losetup /dev/loop${PRE}{} /tmp/raid${PRE}{} ::: 1 2 3 4 5 mdadm --create /dev/md$PRE -c 4096 --level=6 --raid-devices=5 /dev/loop${PRE}[12345] cat /proc/mdstat mkfs.xfs -f /dev/md$PRE mkdir -p /mnt/disk2 umount -l /mnt/disk2 mount /dev/md$PRE /mnt/disk2 seq 1000 | parallel -j1 mkdir -p /mnt/disk2/{}\;cp /bin/* /mnt/disk2/{}\;sleep 0.5 & mdadm --fail /dev/md$PRE /dev/loop${PRE}3 /dev/loop${PRE}4 cat /proc/mdstat # Assume reboot so no process is using the dir kill %1; sync & kill %1; sync & # Force fail one too many mdadm --fail /dev/md$PRE /dev/loop${PRE}1 parallel --tag -k mdadm -E ::: /dev/loop${PRE}? | grep Upda # loop 2,5 are newest. loop1 almost newest => force add loop1 Next step is to add loop1 back - and this is where I am stuck. After that do a xfs-consistency check. When that works, check that the solution also works on real devices (such a 4 USB sticks).

  Read the article

• My new hard drive doesn't have rights on my old one?

  - by Allan

  Until recently I had a 1 TB hard disk with Windows 7 on it, I have bought myself a SSD, removed the old harddisc and installed Windows 7 on my new one. After that I put back the old hard disk, and formatted it, now I could use that as backup and to keep files on. Nice, right? Well I was updating .Net framework through Windows update, when it stalled. I noticed some space was used on one of the drives on my secondary 'previously primary' hard disk. Apparently it was the .Net framework, trying to save some temporary files on my secondary disc, because it was the one with the most space. It was like it didn't get access. I cancled the installation and rebooted the computer. Now wanting to remove the temporary folder on my secondary harddisk. It told me. "You don't have access by SYSTEM", I don't understand, my user is administrator, its the only user there is and at the same time I can remove and delete any other folder on that drive. I'm gonna go a little pseudo here. But it feels as if the computer treats the old harddisk as protected from tampering by the new SSD. Also, I feel I should mention, they are both listed as primary, ... primary 0 and primary 1. Both using SATA cable. My old hard drive was partioned into 3 drives. 2 of them said the current owner was 'Administrator/myPCname' and the third one said the current owner was 'SYSTEM' I changed them all into the only one that I could pick from the list, which is my user since the 'Administrators/myPCname' wasn't exactly wrong.. could it be that they were somehow still attached to the old OS?.. the fact is I named my computer the exact same thing as it was called before installing a new windows.. so I can't really tell if its an old ownership or not. Also.. I'm currently logged in as 'myname' and I'm administrator.. now trying to delete the previously mentioned files.. it says 'you need access from 'myname' – and it can't delete.. That seems really messed up, I mean I'm logged in as the name it wants me to use. Is there maybe someway I could reset all the users on my computer? Or create some default? I don't know – I just want it to take a form I have always known, from a standard Windows point of view.

  Read the article

< Previous Page | 75 76 77 78 79 80 81 82 83  | Next Page >