Search Results

Search found 27931 results on 1118 pages for 'custom configuration'.

Page 793/1118 | < Previous Page | 789 790 791 792 793 794 795 796 797 798 799 800  | Next Page >

• Using PVLANs with normal VLANs in a trunked environment

  - by user974896

  Assume a trunked environment with two switches, S1 and S2. The swtiches are connected with a trunk port designed to pass VLAN 26. What would happen if VLAN 26 on S2 is configured as a private-vlan with the default gateway and DHCP server and default gateway as promisc ports. What if S1's VLAN 26 is configured as a standard VLAN. Would the hosts on S1 be able to communicate with the promisc ports on S2? Would they be able to communicate with the hosts on S2? To further complicate things what if the DHCP server were to reside on S1 and I wanted S2 to have private VLANS with promisc ports as the gateway and DHCP server while still leaving S1 in a standard vlan configuration.

  Read the article

• Windows 7 "Could not reconnect all network drives" on boot

  - by Thermionix

  Windows 7 won't reconnect to my network drives on startup. Once it is done booting opening Windows Explorer and clicking each share will mount them. Windows 7 Enterprise N Service Pack 1 I have attempted formatting the windows machine - first thing done to machine was to map the network drives, upon reboot they were disconnected. It is running on an Crucial M4 64gb SSD. The host of the network shares is a Ubuntu-Server machine connected through a gigabit switch. A modem provides dhcp, although both these machines have static IP's defined. It won't reconnect the drives regardless of whether they're SAMBA shares or NFS shares - therefore I believe it's an issue with the windows machine. Ubuntu 11.10 (GNU/Linux 3.0.0-12-server x86_64) I've tried using ip address instead of netbios name for mapping shares on the windows machine, Also tried setting EnableLinkedConnections=1 gpedit.msc Computer Configuration - Administrative Templates - System-Logon - always wait for the network at computer startup and logon = yes

  Read the article

• How to move ubuntu 12.04 on another drive

  - by Maksim

  How I can move my ubuntu on another drive? I know about clonezilla but problem is that destination drive is smaller the source one. Gparted can't copy-paste partition if destination not the end last partition. I tried dpkg --selected-packages and apt-clone. First one just not install all my packages and removed existed that now I have no full unity and not my all packages. Second one just fail on configuration package. But before I did that way I copy-paste my /etc to new system. My partition table destination : gpt 1 1049kB 106MB 105MB fat32 EFI System ??????????? 2 106MB 12,1GB 12,0GB ext4 3 12,1GB 66,3GB 54,2GB ext4 source: msdos 1 1049kB 12,0GB 12,0GB primary ext4 ??????????? 2 12,0GB 492GB 480GB primary ext4 3 492GB 500GB 8107MB primary linux-swap(v1) Gpt not working with ubuntu that use grub 1.99. I don't know why but my laptop can't boot any device with uefi just black screen and ubuntu detect it on fresh install.

  Read the article

• Can't configure 5.1 audio with 12.04

  - by xster

  I have an Intel ALC892 and a Nvidia GT 520m connected to speakers via HDMI. On lspci, I see 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) Subsystem: ZOTAC International (MCO) Ltd. Device a218 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at db400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel 02:00.1 Audio device: NVIDIA Corporation HDMI Audio stub (rev a1) Subsystem: ZOTAC International (MCO) Ltd. Device 2180 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at db080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel My alsamixer looks like I enabled pulseaudio configuration file to have 6 channels. My sound setting looks like When I use the test dialog, only front left and right have sounds. If I use alsa in XBMC on a 5.1 video, there's no sound. If I use pulseaudio, only front right and left have sound. I can barely hear any speech since I'm guessing it's mapped to front center. Any clues?

  Read the article

• MySQL Cluster Failover doesn't work

  - by Lukasz

  I have two servers, where First server 10.100.15.150: 1. one mgm server 2. one ndbd 3. one mysql api Second server 10.100.15.160: 1. one ndbd 2. one mysql api When i start all 'parts' of cluster it looks : Cluster Configuration [ndbd(NDB)] 2 node(s) id=21 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17, Nodegroup: 0) id=22 @10.100.15.160 (mysql-5.1.56 ndb-7.1.17, Nodegroup: 0, Master) [ndb_mgmd(MGM)] 1 node(s) id=3 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17) [mysqld(API)] 2 node(s) id=11 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17) id=12 @10.100.15.160 (mysql-5.1.56 ndb-7.1.17) When i shutdown first machine - 10.100.15.150, on second the nbdb process also has been shutdown so i cannot use this data node and cluster fail ... How i must configure this cluster to get FailOver working ? Thx

  Read the article

• Setting up sendmail to perform mail routing

  - by Diden

  Is sendmail is able to do the following: Forward many user emails to office 365:- [email protected] -> [email protected] [email protected] -> [email protected] [email protected] -> [email protected] [email protected] -> [email protected] Forward the following to a separate server to run php scripts:- [email protected] [email protected] An autoresponder will be sent to the sender. Does anyone know of any sample configuration I could get this started on? Is there a good autoresponder for sendmail? Our emails are hosted on Office365 and it does not allow us to run scripts. Therefore I was considering this option. Is this viable? Please refer to the diagram for more information. Thank you.

  Read the article

• Hiding "Syntax OK" from apache2ctl output

  - by Oscar Barrett

  I am checking whether a particular apache module is installed using apache2ctl -M. When listing the modules, apache runs a syntax check on the configuration files which prints out "Syntax OK" if everything is fine. However, this message doesn't seem to be coming from STDOUT or STDERR as it shows even if all output is redirected to /dev/null. i.e. $ sudo apache2ctl -M Loaded Modules: core_module (static) log_config_module (static) ... Syntax OK $ sudo apache2ctl -M >/dev/null Syntax OK How is this being outputted, and is it possible to hide?

  Read the article

• How does Apache handle port forwarding?

  - by vfclists

  I setup a localhost portforwarding configuration in the coLinux .conf file, forwarding port 8090 to port 80 in the VM. When http://localhost:8090 is entered in the browser, I get the correct response from nginx, but with Apache the response get the error /htdocs not found in the log. However if I do a local port forwarding from 8090 to port 80 via SSH Apache responds fine. Is there something about the way Apache handles the port redirection that causes it to fail? PS, For those unfamiliar with coLinux it allows localhost connections to get to the VM by forwarding localhost ports on the Windows host to ports on the VM, as the 10.x.x.x IP it not accessible from the Windows host.

  Read the article

• Protect individual sites on Ubuntu/Apache server

  - by Christoffer

  Hi,?? I need to set up a Apache server configuration for some client sites that run under the same Ubuntu 9.10 machine. All sites are allowed to run PHP, Python and Ruby on Rails. I do not control the source code of these sites and so I need to set up a filter in order to prevent one user to reach files on another users account.?? If I run a script to list files in "/" from one account, I can browse some files and directories in the actual server root. I want to set the root for each account to /var/usersite.com/www/ instead so that listing files in "/" shows the files in the client's root. ??How is this most easily configured??? Cheers!? /Christoffer

  Read the article

• Trying to move away from PHP/Yii: RoR, Python/Django or ASP.NET MVC? Your opinions please [closed]

  - by Örs

  I have a CS degree and I've been working as a web developer (front & backend) for about 2 years now. I've been working with PHP mostly because it was easy to pick up and find a job, but I've grown to dislike the language and want to try something new, and possibly get a better paying job. That last point is especially important because in my area (Romania/Eastern Europe) PHP jobs are mostly for people fresh out of college/high school, hence the pay is rather low. I've been working with the Yii framework which, if I understand correctly, borrows a lot from Ruby on Rails (convention over configuration, MVC, Active Record, scaffolding). Other than PHP I only know curly-brace languages (C/C++/Java) and bash so Python/Ruby might be a bit challenging. On the other hand I've been using Linux (with vim and recently Sublime Text 2) for almost 4 years now so Windows and a lack of a terminal would have its downsides as well. I'm leaning towards Python/Ruby because of my *nix bias (plus both look like fun), but I've heard great things about ASP.NET MVC as well. Any suggestions? PS: I think there are more jobs in ASP.NET around here, but that's not necessarily a plus, because there are a lot of CS graduates as well. tl;dr: Romanian PHP/Yii developer trying to move to Python/Django or Ruby/Rails or C#/ASP.NET MVC. Suggestions?

  Read the article

• Interaction between two Clouds

  - by user7969

  I have setup the Cloud-A with 1 - [CLC+CC] and 2 - [NC] computers. I have another Cloud-B with same configuration. [using the Ubuntu Enterprise Cloud] Both of them working fine individually, in the same LAN. Now if I want to add the NC of Cloud-A to CC of Cloud-B, [in case the resources of Cloud-B are exhausted] how can I make it possible ? I guess this calls for the interoperability stuff... Could you please explain what happens exactly when we ask for instance, the direct interaction happens between the client and NC or it goes through the CLC and CC ? What I want to say is, say there are multiple cloud providers. A user is subscribed to any one of them, say Cloud-A for IaaS. As the requirements are dynamic, all the resources of Cloud-A may get exhausted. There may be another Cloud-B which can provide the services but that Cloud-A can't ask the client to go for Cloud-B. So if it is possible to have some co-ordination between this two providers to share resources mutually, making client fully unaware of whats going on in the background....? Please reply.. I am sorry if I'm doing mistake anywhere... Thanks in advance :)

  Read the article

• my.cnf in server directory, why

  - by Mellon

  On my Ubuntu machine, I have installed MySQL . I notice that there are /etc/my.cnf file which contain the content (only two lines): innodb_buffer_pool_size = 1G max_allowed_packet = 512M While there is also /etc/mysql/my.cnf with a long content like: # The MySQL database server configuration file. ... ... For me, it looks like both are configurations for MySQL server, but Why there are two my.cnf in different locations, can't the content to be merged to one my.cnf ? What is the purpose to have seperate my.cnf for MySQL server ?

  Read the article

• Graphic Setup tune-up checklist

  - by Click Ok

  I was trying to play the game Warzone 2100 and the games runs fine, with nice speed, but the screen stays with a horizontal lines "flickering"... My PC have a integrated GeForce Go 6100 vga. Ok, not a powerfull vga, but it's not the end of the world to run a "simple" game like this (compared with another games that ask you send your eyes to purchase a expensive vga). So, I think that the problem can be of the configuration of my machine. I use it in first instance for programming jobs, so I underpay attention to video setup. I would like about a checklist to know if my PC is "ready" to games. By example, I know that I need: Lastest vga drivers Updated DirectX and OpenGL What you suggest? There is too some good programs to test performance and suggests improvements in the system? Thank you! PS: I'm using Windows 7

  Read the article

• What is the value/cost of enabling "spread spectrum clocking" on my hard drives?

  - by Stu Thompson

  I'm building up a biggish NAS box (10x WD RE4 2TB SATA RAID10) and ran into some problems. During the course of my research, debugging, investigations, etc, I discovered a jumper on the physical drives labeled "spread spectrum clocking". After some googling about this on teh internets, it seems to be a feature that some suggest (without reference or explanation) enabling in 'a storage configuration' that makes the drive less sussesptable to EMI. But why? I've got three core questions: Why is this feature not enabled by default? What are the actual benefits? Are there any costs?

  Read the article

• Bind9 forwarding zone not working

  - by JMW

  i've setup a forwarding zone on a RHEL6 Bind server like this: zone "office.local" IN { type forward; forward only; forwarders { 192.168.0.2; 192.168.0.3; }; }; when i try to query using dig @127.0.0.1 monitorsms.office.local i see the following message in the syslog: client 127.0.0.1#39376: query: monitorsms.office.local IN A + (127.0.0.1) validating @0x7ff7640357d0: monitorsms.office.local A: bad cache hit (monitorsms.office.local/DS) google tells me, that there is an issue with DNSSEC, but both servers do not have DNSSEC configured and thus do not send any DNSSEC records. What's wrong with my configuration?

  Read the article

• How to configure Apache for PHP on Windows 7?

  - by salim cobra

  I have installed Apache 2.0(httpd-2.0.64-win32-x86-no_ssl) and it works, then I have installed Php5.3 and it pointed to Apache configuration folder. failed scenario: 1- create simple test.php, put in under C:\Apache\Apache2\htdocs 2- call "http://localhost:8080/test.php" -- "Bad Request..Your browser sent a request that this server could not understand." Proposed solution by NetBeans blog (failed) 1-add those two lines to httpd.conf AddType Application/x-httpd-php .php LoadModule php5_module "c:/php/sapi/php5apache2_2.dll" It doesnt works because there is no "php5apache2_2.dll" under my Php installation folder?? I have such .dll : php5ts.dll, ssleay32.dll,.. Any one have any suggestion in order to run the PHP script successfully?

  Read the article

• Disabling monitor reconfiguration when closing lid

  - by Tomas

  I often need to move my laptop from one working place to another. When I do this, there are two events Ubuntu responds to by changing the monitor set up: Removing/attaching the VGA cable Closing/opening the lid of the laptop While removing the VGA cable gives me what I need (single screen, highest native resolution on the external screen if connected; otherwise highest resolution on the laptop), the laptop close/open lid response is not as good. Every time I close or open the lid, Ubuntu reconfigures the monitor set up. When I close the lid now... the screen goes black for a few seconds and it switches to clone, with my laptop screen disabled. Reopening results in... briefly a black screen, then the external monitor being used as desktop extension. Ubuntu thinks too much. My first and foremost question: Is there any way to let Ubuntu ignore lid close events? Ideally (or when there's no way to solve above question) I'd want to change how it deals with the screen reconfiguration. Why does Ubuntu toggle the screen configuration between external, clone and single display? Can't I just configure it to always use the external monitor, when present, in single screen mode? Note that similar questions have been asked before (most notably this one), but these have been closed perhaps wrongly. Any ideas are very welcome, I don't mind playing around a bit to see if something works.

  Read the article

• Setting up multiple cores for apache solr for Ubuntu 12.04 and Drupal 7

  - by chrisjlee

  I'm setting up solr locally for my development purposes and integration with Drupal 7. I'm not very familiar with tomcat. My background has primarily been LAMP setups. So I went and installed the package provided by ubuntu for apache solr following this guide. sudo apt-get install tomcat6 tomcat6-admin tomcat6-common tomcat6-user tomcat6-docs tomcat6-examples sudo apt-get install solr-tomcat I've got that working. The apt-get package manager does a great job and allows me to setup solr but with one core. What steps need to be taken to enable multi core setup for apache solr? And below is my solr.xml file: sudo nano /var/lib/tomcat6/conf/Catalina/localhost/solr.xml <!-- Context configuration file for the Solr Web App --> <Context path="/solr" docBase="/usr/share/solr" debug="0" privileged="true" allowLinking="true" crossContext="true"> <!-- make symlinks work in Tomcat --> <Resources className="org.apache.naming.resources.FileDirContext" allowLinking="true" /> <Environment name="solr/home" type="java.lang.String" value="/usr/share/solr" override="true" /> </Context>

  Read the article

• Cisco Router 1921

  - by mytempfw

  I'm very new in networking and I'm trying to setup my network as follow [ISP Modem/Router/Switch] + --- + {fxp0} [Linux Firewall] {fxp1} + --- + {??} [Cisco Router 1921] {GE 0/0} + --- + [Cisco Switch] + ... Servers {GE 0/1} + --- + [Cisco Switch] + ... Servers My questions are, Since I'm using both GE 0/0 and GE 0/1 ports to connect to switch, how can I connect my Linux Firewall (Port fxp1) to my Cisco Router? I know the USB and Console port are for configuration, can I use AUX port to connect my firewall (if so is it consider a right way)? Is my setup is right? if not can someone please explain to me to do the setup in right way. Link to the picture of my router: Cisco Router 1921 Thanks

  Read the article

• Vim - How Recognize Spaces as Tabs (set listchars=tab)

  - by Eduardo Lucio

  I wonder if it is possible to use a configuration for that command "set listchars=tab:¦¦,trail:·" to "see" 4 spaces as tabs and get the effect of the picture below (using real tabs)... I use the setting "set expandtab" to Vim use spaces in place of tabs. I really need to use spaces instead of tabs, but I would keep the functionality above. There is some form of do this? Here's how Vim behaves when I use "set expandtab"... ... I wish he recognized one tab for every 4 spaces like above! My setup for tabs... set tabstop=2 set shiftwidth=2 set softtabstop=2 set expandtab Thank you!

  Read the article

• All hail the Excel Queen

  - by Tim Dexter

  An excellent question this past week from dear ol Blighty; actually from Brian at Nextgen Clearing Ltd in the big smoke (London). Brian was developing an excel template and wanted to be able to reference the data fields multiple times inside the Excel template. Damn good question and I of course has some wacky solutions, from macros and cell referencing in Excel to pre-processing the data with an XSL stylesheet to copy the data multiple times so it could be referenced multiple times. All completely outlandish, enter our Queen of Excel, Shirley from the development team. Shirley is singlehandedly responsible for the Excel templates, I put her through six months of hell a few years back, with a host of Excel template requirements. She was more than up to the challenge and has developed some great features. One of those, is the ability to use the hidden XDO_METADATA sheet to map the data to custom named fields so they can be used multiple times in the template. So simple and very neat! Excel template and regular Excel users will know that you can only use the naming function once ie the names have to be unique across the workbook so you can not reuse a cell/group name. To get around this you can just come up with as many cell names as you want and map them in the XDO_METADATA sheet to the data columns/fields in your XML data set:. For example: XDO_?DEPTNO_SUMMARY?  <?DEPTNO?> XDO_?DNAME_SUMMARY?  <?DNAME?> XDO_GROUP_?G_D_DETAIL? <xsl:for-each-group select=".//G_D" group-by="./DEPTNO"> XDO_?DEPTNO_DETAIL? <?DEPTNO?> As you can see DEPTNO has been referenced twice and mapped to different named values in the left hand column. These values can then be used to name individual cells in the Excel template. You'll also notice a mix of Publisher <? ...?> and native XSL commands. So the world is your oyster on the mapping and the complexity you might need for calculations or string manipulation. Shirley has kindly built out a sample Excel template, data and result here so you can see how it all hangs together. the XDO_METADATA sheet is hidden, just right click on the sheet names and use the Unhide command to show it.

  Read the article

• Why is apt-cache so slow?

  - by Damn Terminal

  After upgrade to Trusty (14.04) from Saucy (13.10), all apt operations are very slow. Even those that do not include downloading anything, or connecting to any servers. For example, displaying the apt policy # time apt-cache policy [...] real 0m8.951s user 0m5.069s sys 0m3.861s takes almost ten seconds! Mostly a weird lag right after issuing the command. And it's the same even if I issue the same command again. On another system it doesn't take a tenth of a second real 0m0.096s user 0m0.070s sys 0m0.023s The other system is a little beefier but there was no noticeable difference before the upgrade. It's the same with apt-get, anything apt-related. How do I find out the source of this lag and fix it? Additional info: # cat /etc/nsswitch.conf # /etc/nsswitch.conf # # Example configuration of GNU Name Service Switch functionality. # If you have the `glibc-doc-reference' and `info' packages installed, try: # `info libc "Name Service Switch"' for information about this file. passwd: compat group: compat shadow: compat hosts: files dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis BTW is my understanding of how apt-cache works correct? It doesn't make any network connections when I run apt-cache policy, right? In case I'm wrong and it matters, here are my sources https://gist.github.com/anonymous/02920270ff68e23fc3ec

  Read the article

• Installing libssh2 on debian

  - by Ajay

  Hi I'm trying to install libssh2 for 64-bit. I'm using the following code for installation: cd libssh2-1.4.3/ export CFLAGS="-mabi=64 -march=mips64r2" ./configure --with-libz --with-libgcrypt --with-libz-prefix=`pwd`/../../support__ libs/libs/zlib/ --with-libgcrypt-prefix=`pwd`/../../support_libs/``libs/extra --wii thout-libssl-prefix --prefix=`pwd`/../../support_libs/libs/extra_2 make && make install without using "export CFLAGS="-mabi=64 -march=mips64r2" it compiles the binaries in 32-bit and whem i use #export for 64-bit, it gives this configuration error:: checking for libgcrypt... no configure: error: cannot find OpenSSL or Libgcrypt, try --with-libssl-prefix=PATH or --with-libgcrypt-prefix=PATH make: *** No targets specified and no makefile found.

  Read the article

• How can I get a list of default documents in IIS using PowerShell?

  - by SGarratt

  I'm managing a Server Core machine and trying to do everything in PowerShell, which is fun. I need a list of the default documents. From other websites, I've found out how to set and remove them, using both xxx-WebConfiguration and xxx-WebConfigurationProperty. I've tried: Get-WebConfigurationProperty -Filter /system.webServer/defaultDocument -PSPath "IIS:\sites\Default Web Site" -Name files but it gives: Collection : {Microsoft.IIs.PowerShell.Framework.ConfigurationElement, Microsoft.IIs.PowerShell.Framework.Configuration Element, Microsoft.IIs.PowerShell.Framework.ConfigurationElement, Microsoft.IIs.PowerShell.Framework.Confi gurationElement...} ItemXPath : /system.webServer/defaultDocument Attributes : {} ChildElements : {} ElementTagName : files Methods : Schema : Microsoft.IIs.PowerShell.Framework.ConfigurationElementSchema which doesn't really help.

  Read the article

• OpenVPN (HideMyAss) client on Ubuntu: Route only HTTP traffic

  - by Andersmith

  I want to use HideMyAss VPN (hidemyass.com) on Ubuntu Linux to route only HTTP (ports 80 & 443) traffic to the HideMyAss VPN server, and leave all the other traffic (MySQL, SSH, etc.) alone. I'm running Ubuntu on AWS EC2 instances. The problem is that when I try and run the default HMA script, I suddenly can't SSH into the Ubuntu instance anymore and have to reboot it from the AWS console. I suspect the Ubuntu instance will also have trouble connecting to the RDS MySQL database, but haven't confirmed it. HMA uses OpenVPN like this: sudo openvpn client.cfg The client configuration file (client.cfg) looks like this: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client auth-user-pass #management-query-passwords #management-hold # Disable management port for debugging port issues #management 127.0.0.1 13010 ping 5 ping-exit 30 # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. #;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. proto tcp ;proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. # All VPN Servers are added at the very end ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. # We order the hosts according to number of connections. # So no need to randomize the list # remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca ./keys/ca.crt cert ./keys/hmauser.crt key ./keys/hmauser.key # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ;ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. #comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 # Detect proxy auto matically #auto-proxy # Need this for Vista connection issue route-metric 1 # Get rid of the cached password warning #auth-nocache #show-net-up #dhcp-renew #dhcp-release #route-delay 0 120 # added to prevent MITM attack ns-cert-type server # # Remote servers added dynamically by the master server # DO NOT CHANGE below this line # remote-random remote 173.242.116.200 443 # 0 remote 38.121.77.74 443 # 0 # etc... remote 67.23.177.5 443 # 0 remote 46.19.136.130 443 # 0 remote 173.254.207.2 443 # 0 # END

  Read the article

< Previous Page | 789 790 791 792 793 794 795 796 797 798 799 800  | Next Page >