Search Results

Search found 588 results on 24 pages for '802 11b'.

Page 8/24 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• HP Pavilion tx2000 - Wifi adapter no longer works after moving from 12.04 to a 12.10 clean install

  - by Marek L.

  I have a HP Pavilion tx2000 that I have been running Ubuntu 12.04 on for a couple of months without any problems (wifi worked great) until yesterday when my hard drive failed. I replaced the hard drive and decided to install Ubuntu 12.10. Unlike 12.04, the wifi did not work after the installation finished and all the updates where installed (over Ethernet). The network drop down in the top right didn't even show a wireless option. I Googled about for a bit and found some solutions that seemed like they might work. Unfortunately they did not. Here is what I tried: sudo apt-get remove bcmwl-kernel-source sudo apt-get install b43-fwcutter sudo apt-get install firmware-b43-lpphy-installer Restart the computer. And the wifi still didn't work. At which point I panicked a bit and tried to undo the previous commands by running: sudo apt-get remove b43-fwcutter firmware-b43-lpphy-installer sudo apt-get install bcmwl-kernel-source Restart the computer. The wifi still doesn't work. This is where I stopped because I have no idea what I am doing and don't want to mess something up. The network drop down still doesn't show a wireless option and the hardware wifi switch on the laptop is amber (it turns blue when the wifi is on). Using the hardware switch does not change the color. Output from: sudo lspci ... 08:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01) ... Output from: sudo lshw -class network *-network UNCLAIMED description: Network controller product: BCM4322 802.11a/b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1100000-d1103fff ... Output from: sudo rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes UPDATE: After writing up this question tried the following command: sudo rfkill unblock all At first it didn't do anything but after running it about four times, sudo rfkill list all now returns: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no But the network menu still does not have a wireless option and the hardware switch still glows amber. Pushing the hardware switch turns the hard block back on and I have to run sudo rfkill unblock all multiple times again to turn it off. Any help is appreciated! Update 2: Full output from sudo lspci -nn: 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600] 00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) [1022:9602] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0) [1022:9604] 00:05.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1) [1022:9605] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) [1022:9606] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] 00:12.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:12.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:12.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] 00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller [1002:4398] 00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller [1002:4385] (rev 3a) 00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) [1002:4383] 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d] 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge [1002:4384] 00:14.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor HyperTransport Configuration [1022:1300] (rev 40) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Address Map [1022:1301] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor DRAM Controller [1022:1302] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Miscellaneous Control [1022:1303] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 11h Processor Link Control [1022:1304] 01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RS780M/RS780MN [Mobility Radeon HD 3200 Graphics] [1002:9612] 08:00.0 Network controller [0280]: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] (rev 01) 09:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• Javascript REGEX

  - by Fernando SBS

  <th>Prêmio</th> <td colspan="11"> <div class="res"><img class="r1" src="img/x.gif" alt="Madeira" title="Madeira" />215 | <img class="r2" src="img/x.gif" alt="Barro" title="Barro" />193 | <img class="r3" src="img/x.gif" alt="Ferro" title="Ferro" />192 | <img class="r4" src="img/x.gif" alt="Cereal" title="Cereal" />202</div><div class="carry"><img class="car" src="img/x.gif" alt="carregamento" title="carregamento" />802/1800</div></td></tr></tbody></table><table cellpadding="1" cellspacing="1" class="defender"> <thead> <tr> i'm trying to get "802/1800", but it's driving me insane. if I use: var myregexp = /title="carregamento"/; it works but going to the next step which is: var myregexp = /title="carregamento" \/>/ already returs me null.

  Read the article

• Linux bcm43224 wifi adapter slows down a couple minutes after boot

  - by Blubber

  I just installed Ubuntu on my mid 2012 MacBook Air. Everything worked out of the box, but the wifi is showing some weird behavior. When I first login it's really fast, loading google.com is near instant, and browsing in general feels at least as smooth as it did on Mac OS. However, after a couple minutes the connection slows down dramatically, sometimes it takes over 5s to load google.com, a simple reboot fixes the problem for another couple minutes. Specs: Wifi: 02:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Driver: open-source brcmsmac driver Kernel: Linux wega 3.8.0-21-generic #32-Ubuntu SMP Tue May 14 22:16:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Distro: Ubuntu 13.04 (uptodate) I tried a number of things, none of which actually helped Use proprietary sta driver from broadcom Installed firmware into /lib/firmware/brcms (which, as far as I can tell from logs, does not get loaded at all) Switch router to only use 2.4 OR 5 GHz Set router to only use a OR g OR n Set router to use AES encryption only Turned off power management on the adapter Set regulatory region to the correct value (NL) on both router and laptop Disable ipv6 Nothing seems to help, the slowdown always occurs. I did notice that the latency (ping google.com) stays roughly the same (around 9ms). Below is some more information that might be of use. $ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) Subsystem: Apple Inc. Device [106b:00e9] Kernel driver in use: bcma-pci-bridge $ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lsmod Module Size Used by dm_crypt 22820 1 arc4 12615 2 brcmsmac 550698 0 coretemp 13355 0 kvm_intel 132891 0 parport_pc 28152 0 kvm 443165 1 kvm_intel ppdev 17073 0 cordic 12574 1 brcmsmac brcmutil 14755 1 brcmsmac mac80211 606457 1 brcmsmac cfg80211 510937 2 brcmsmac,mac80211 bnep 18036 2 rfcomm 42641 12 joydev 17377 0 applesmc 19353 0 input_polldev 13896 1 applesmc snd_hda_codec_hdmi 36913 1 microcode 22881 0 snd_hda_codec_cirrus 23829 1 nls_iso8859_1 12713 1 uvcvideo 80847 0 btusb 22474 0 snd_hda_intel 39619 3 videobuf2_vmalloc 13056 1 uvcvideo snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_cirrus bcm5974 17347 0 bluetooth 228619 22 bnep,btusb,rfcomm snd_hwdep 13602 1 snd_hda_codec lpc_ich 17061 0 videobuf2_memops 13202 1 videobuf2_vmalloc videobuf2_core 40513 1 uvcvideo videodev 129260 2 uvcvideo,videobuf2_core bcma 41051 1 brcmsmac snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 16 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_cirrus mei 41158 0 soundcore 12680 1 snd apple_bl 13673 0 mac_hid 13205 0 lp 17759 0 parport 46345 3 lp,ppdev,parport_pc usb_storage 57204 0 hid_apple 13237 0 hid_generic 12540 0 ghash_clmulni_intel 13259 0 aesni_intel 55399 399 aes_x86_64 17255 1 aesni_intel xts 12885 1 aesni_intel lrw 13257 1 aesni_intel gf128mul 14951 2 lrw,xts ablk_helper 13597 1 aesni_intel cryptd 20373 4 ghash_clmulni_intel,aesni_intel,ablk_helper i915 600351 3 ahci 25731 3 libahci 31364 1 ahci video 19390 1 i915 i2c_algo_bit 13413 1 i915 drm_kms_helper 49394 1 i915 usbhid 47074 0 drm 286313 4 i915,drm_kms_helper hid 101002 3 hid_generic,usbhid,hid_apple $ dmesg | egrep 'b43|bcma|brcm|[F]irm' [ 0.055025] [Firmware Bug]: ioapic 2 has no mapping iommu, interrupt remapping will be disabled [ 0.152336] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 2.187681] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-99] only partially covers this bridge [ 12.553600] bcma-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002) [ 12.553657] bcma: bus0: Found chip with id 0xA8D8, rev 0x01 and package 0x08 [ 12.553688] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 12.553715] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 12.553764] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 12.605777] bcma: bus0: Bus registered [ 12.852925] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 17 [ 13.085176] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement) [ 13.085186] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement) [ 20.862617] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated [ 20.862622] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 20.862625] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 20.897957] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"wlan" Mode:Managed Frequency:5.22 GHz Access Point: E0:46:9A:4E:63:9A Bit Rate=65 Mb/s Tx-Power=17 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=63/70 Signal level=-47 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:13 Invalid misc:56 Missed beacon:0

  Read the article

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• Ubuntu 13.10 isn't remembering my passwords anymore, why?

  - by Nik Reiman

  Ubuntu's password management used to be working just fine for me, but around two weeks ago after running apt-get upgrade, I've noticed that now it keeps "forgetting" my passwords. For instance, I need to manually enter passwords to unlock my ssh keys to use git, which previously was done automatically on login. My workplace's 802.11x authentication also no longer works, I need to manually re-auth just to connect to internet. What's going on?

  Read the article

• Ralink rt3090 driver installed and wireless doesn't work on Ubuntu 10.04

  - by Marcus Rene

  I have a LG A-410 lap-top (64 bits) with rt 3090 wireless card. Searching the problem I discover that I already have a rt 3090-dkms installed, but my wireless doesn't work. *-network UNCLAIMED description: Network controller product: RT3090 Wireless 802.11n 1T/1R PCIe vendor: RaLink physical id: 0 bus info: pci@0000:02:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:e5400000-e540ffff

  Read the article

• Broadcom BCM4331 not working on new Mac Mini 5,1

  - by Jon

  I can't seem to get my wireless card working on my Mac Mini 5,1. Lspci returns: 03:00.0 Network controller: Broadcom Corporation BCM4331 802.11a/b/g/n (rev 02) But running "additional drivers" doesn't detect anything. The nm-applet menu reads "device not ready--firmware missing." What can I do to get this to work? Note, this is with 12.04.1, so many of the previous discussions (for 11.10, etc) probably don't apply here.

  Read the article

• Atheros AR9285 / Lenovo G560 wireless not working after installing 13.04

  - by teyi

  I had Ubuntu 12.04 initially installed on my laptop. I upgraded to 12.10 then 13.04. Everything worked fine, including wireless. After adding a new memory card ( I only had 2 gb and one memory slot free) my wireess stopped working. I backed up all my data and reinstallled Ubuntu 13.04. Everything works fine except wireess. I bought this laptop in 2010 from Japan. It has Intel Core i5 CPU M 450 @2.40 Ghz * 4 3,7 Gb RAM os type 64 bit The output of iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off The output of rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no The output of lshw -C network: *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:7d:fe:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d6400000-d640ffff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 02 serial: 88:ae:1d:2b:36:ac size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d2410000-d2410fff memory:d2400000-d240ffff memory:d2420000-d243ffff The wi-fi network appears as disconnected ( it's greyed out) Strangely enough I see a wifi network ( not mine) but not mine or the rest. That network doesn't require a password . I click on it, try to connect and i get an error message: failed to connect to xxxxx ... 32) The access point/org/freedesktop/NetworkManager/AccessPoint/0 was not in the scan list. Someone help please

  Read the article

• Wireless Adapter Review: hField Wi-Fire

  Tired of weak and wimpy WiFi? This clip-on replacement for your laptop's 802.11b/g adapter promises up to triple the range, plus finding wireless networks you couldn't access before. Is it the best $59 a road warrior ever spent?

  Read the article

• Wireless Adapter Review: hField Wi-Fire

  Tired of weak and wimpy WiFi? This clip-on replacement for your laptop's 802.11b/g adapter promises up to triple the range, plus finding wireless networks you couldn't access before. Is it the best $59 a road warrior ever spent?

  Read the article

• Ubuntu 11.04 Broadcom BCM4312 Not Working

  - by ptran221

  I have a HP MINI 210-1010NR and just installed Ubuntu 11.04 and I can't get my wireless to work.I have checked through multiple Q&A's throughout this FAQ and tried them all. When I go over the wireless thing at the top it says "Wireless Networks device not ready(firmware missing)." Okay, now here is my ~$ lspci -vvnn | grep 14e4 02:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Also, when I try to open additional drivers it says that "Downloading package indexes failed, please check your network status."

  Read the article

• Broadcom BCM4312 Not Working

  - by ptran221

  I have a HP MINI 210-1010NR and just installed Ubuntu 11.04 and I can't get my wireless to work.I have checked through multiple Q&A's throughout this FAQ and tried them all. When I go over the wireless thing at the top it says "Wireless Networks device not ready(firmware missing)." Okay, now here is my lspci -vvnn | grep 14e4 02:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Also, when I try to open additional drivers it says that "Downloading package indexes failed, please check your network status."

  Read the article

• Wifi disabled for Intel Centrino Wireless-N 1000 Intel in 12.04

  - by new_bie

  Laptop model - HP- dm4 - 2070. I had faced the same problem for wireless being disabled in case of 11.10. It had to do with the new kernel. I thought with 12.04 this problem will be handled but the problem persists. Is there no way to get the wireless working except for the way mentioned in the following link ?? Wifi for Centrino Wireless-N 1000 Intel Corporation (HP pavillion dm4 - 2070us) is not working Output for sudo lshw -class network *-network UNCLAIMED description: Network controller product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:c2500000-c2501fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: c0 serial: 2c:41:38:07:f3:e3 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.116 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:c1400000-c143ffff ioport:2000(size=128) Output for dmesg | grep iwl [ 14.742886] iwlwifi 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 14.742897] iwlwifi 0000:01:00.0: setting latency timer to 64 [ 14.743013] iwlwifi 0000:01:00.0: pci_resource_len = 0x00002000 [ 14.743016] iwlwifi 0000:01:00.0: pci_resource_base = ffffc90000c78000 [ 14.743018] iwlwifi 0000:01:00.0: HW Revision ID = 0x0 [ 14.743119] iwlwifi 0000:01:00.0: irq 42 for MSI/MSI-X [ 14.743161] iwlwifi 0000:01:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 14.743229] iwlwifi 0000:01:00.0: L1 Enabled; Disabling L0S [ 14.765147] iwlwifi 0000:01:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 14.765151] iwlwifi 0000:01:00.0: Device SKU: 0X50 [ 14.765154] iwlwifi 0000:01:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 14.765907] iwlwifi 0000:01:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 14.912840] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-5.ucode' failed. [ 14.914254] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-4.ucode' failed. [ 14.915718] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-3.ucode' failed. [ 14.916986] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-2.ucode' failed. [ 14.919391] iwlwifi 0000:01:00.0: request for firmware file 'iwlwifi-1000-1.ucode' failed. [ 14.919445] iwlwifi 0000:01:00.0: no suitable firmware found! [ 14.919783] iwlwifi 0000:01:00.0: PCI INT A disabled [ 2868.960807] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_idt rfcomm bnep bluetooth parport_pc ppdev binfmt_misc hid_logitech_dj usbhid hid joydev snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq hp_wmi sparse_keymap hp_accel lis3lv02d input_polldev snd_timer snd_seq_device wmi iwlwifi snd mac80211 i915 cfg80211 rts_pstor(C) drm_kms_helper drm uvcvideo videodev psmouse soundcore mei(C) v4l2_compat_ioctl32 mac_hid serio_raw snd_page_alloc i2c_algo_bit video lp parport atl1c

  Read the article

• Can't get Wireless RT2x00usb driver to work, and can't blacklist it

  - by TheLQ

  After a two year hiatus to Linux, I try it again out again. And then I run into to driver issues... I have an old Linksys WUSB54G v4 Wireless USB Adapter. In previous versions I had to use a combination of Ndiswrapper and Wicd to hope of getting it working. In 10.10, apparently there are built in drivers for it. Unfortunately they don't work. Fails to connect to my WPA network, fails to connect to my open unencrypted network. Wicd fails at "Obtaining IP address" or when using static IPs fails at verifying connectivity to network. Getting fed up I tried the ndiswrapper approach. Installed and configured, but still not working, even when blacklisting the rt2570 module. So for some debugging I added some lines to my /etc/modprobe.d/blacklist.conf file blacklist rt2570 blacklist prism54usb blacklist rt2x00lib blacklist rt2x00usb Restart and find this: lordquackstar@quackbeast:/etc/modprobe.d$ lsmod | grep rt2 rt2500usb 18049 0 rt2x00usb 9779 1 rt2500usb rt2x00lib 27275 2 rt2500usb,rt2x00usb led_class 2633 1 rt2x00lib mac80211 231541 2 rt2x00usb,rt2x00lib cfg80211 144470 2 rt2x00lib,mac80211 Seems to be ignored... Tried this: lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00usb ERROR: Removing 'rt2x00usb': Resource temporarily unavailable lordquackstar@quackbeast:/etc/modprobe.d$ sudo rmmod -f rt2x00lib ERROR: Removing 'rt2x00lib': Resource temporarily unavailable and couldn't connect. Restarted and was back to the same modules loading. Maybe there's something in the log: lordquackstar@quackbeast:/etc/modprobe.d$ tail -n100000 /var/log/syslog | grep rt2 Dec 13 19:01:15 quackbeast kernel: [ 23.698056] Registered led device: rt2500usb-phy0::radio Dec 13 19:01:15 quackbeast kernel: [ 23.698140] Registered led device: rt2500usb-phy0::quality Dec 13 19:01:15 quackbeast kernel: [ 23.701680] usbcore: registered new interface driver rt2500usb Dec 13 19:01:15 quackbeast NetworkManager[855]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Dec 13 19:17:47 quackbeast kernel: [ 23.521759] Registered led device: rt2500usb-phy0::radio Dec 13 19:17:47 quackbeast kernel: [ 23.521824] Registered led device: rt2500usb-phy0::quality Dec 13 19:17:47 quackbeast kernel: [ 23.524740] usbcore: registered new interface driver rt2500usb Dec 13 19:17:47 quackbeast NetworkManager[798]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2500usb' ifindex: 4) Seems to be autoloading. So this means that even if I pull it out, remove the module, and get it working, it still won't work when its plugged in all the time. More info: lordquackstar@quackbeast:/etc/modprobe.d$ sudo lshw -C Network *SNIP* *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:12:17:9b:f3:1e capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=2.6.35-24-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg USB: lordquackstar@quackbeast:/etc/modprobe.d$ lsusb | grep -i rt Bus 001 Device 003: ID 13b1:000d Linksys WUSB54G v4 802.11g Adapter [Ralink RT2500USB] Any suggestions on how to either fix the rt2x00usb driver or permanently block it from loading? Note that I already have ndiswrapper installed

  Read the article

• Bluetooth firmware problem in Ubuntu 13.04

  - by chanzerre

  I have a [Dell Inspiron][1] 15R 5520 laptop. Bluetooth is not working at all. rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no dmesg|grep -i bluetooth gives [ 13.644428] Bluetooth: Core ver 2.16 [ 13.644445] Bluetooth: HCI device and connection manager initialized [ 13.644453] Bluetooth: HCI socket layer initialized [ 13.644455] Bluetooth: L2CAP socket layer initialized [ 13.644461] Bluetooth: SCO socket layer initialized [ 15.861363] Bluetooth: hci0 command 0x1003 tx timeout [ 15.903443] Bluetooth: can't load firmware, may not work correctly [ 17.332535] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.332538] Bluetooth: BNEP filters: protocol multicast [ 17.332544] Bluetooth: BNEP socket layer initialized [ 17.393768] Bluetooth: RFCOMM TTY layer initialized [ 17.393781] Bluetooth: RFCOMM socket layer initialized [ 17.393783] Bluetooth: RFCOMM ver 1.11 hciconfig gives hci0: Type: BR/EDR Bus: USB BD Address: E0:06:E6:D5:DB:46 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN ISCAN RX bytes:687 acl:0 sco:0 events:56 errors:0 TX bytes:2024 acl:0 sco:0 commands:52 errors:0 I have visited the site http://wireless.kernel.org/en/users/Drivers/b43 and according to it lspci -vnn -d 14e4: gives 08:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) Subsystem: Dell Wireless 1704 802.11n + BT 4.0 [1028:0016] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1500000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: wl So I got my PCI-ID as 14e4:4365 which it says is not supported. The alternative is wl. What should I do? My Wi-Fi is working normally without any problems, but Bluetooth is not working. sudo dpkg -i wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb gives following error (Reading database ... 208543 files and directories currently installed.) Unpacking wireless-bcm43142-dkms (from wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb) ... Setting up wireless-bcm43142-dkms (6.20.55.19-1) ... Loading new wireless-bcm43142-6.20.55.19 DKMS files... Building only for 3.8.0-23-generic Building initial module for 3.8.0-23-generic Traceback (most recent call last): File "/usr/share/apport/package-hooks/dkms_packages.py", line 22, in <module> import apport ImportError: No module named apport Error! Bad return status for module build on kernel: 3.8.0-23-generic (x86_64) Consult /var/lib/dkms/wireless-bcm43142/6.20.55.19/build/make.log for more information.

  Read the article

• Wireless not working on Dell Inspirion 1501 after upgrading to Ubuntu 12.04 tried steps in other threads

  - by mark burton

  I updated to Ubuntu 12.04 and now my wireless is not working. No icon for it. Tried some of the troubleshooting in other threads but can't get it to work. Would really appreciate any help Thanks! " *-network description: Network controller product: BCM4311 802.11a/b/g vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 02 serial: 00:19:b9:5c:d1:52 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=10.0.0.6 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff " lsub results Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c526 Logitech, Inc. Nano Receiver $ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:05.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:06.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS482 [Radeon Xpress 200M] 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11a/b/g (rev 01) 08:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) 08:01.0 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 08:01.1 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 01) rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• How to get wireless (Alfa) operate in full power and speed up wireless Internet?

  - by MahboobeAlam

  I am using Wireless to connect to the internet (router). My laptop has Atheros wireless (AR 242x/542x) adapter but the router is a little bit far-away from my room so I have to use an external wireless adapter i.e. Alfa (Realtek 8187) for connectivity. However, since I have started using Ubuntu I noticed that Alfa is not working in full power, internet speed in Ubuntu is much slower than in Windows on my laptop. When I am using Windows 7 the LED (bulb) on Alfa blinks as it should, but when in Ubuntu, it doesn't blink rather it is on but very dim. Connection using Atheros adapter is also the same (slow)... I have tried 4 methods (I found on the Internet) to troubleshoot this matter but no success. It seems to me that Ubuntu/Linux is not letting these wireless adapters to operate in full strength. iwconfig shows that power management is off for both. So what's the problem? Details: ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1e:36:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 TX packets:1657 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:241697 (241.6 KB) TX bytes:241697 (241.6 KB) wlan0 Link encap:Ethernet HWaddr 00:22:5f:9b:24:b5 inet6 addr: fe80::222:5fff:fe9b:24b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:715460 errors:0 dropped:0 overruns:0 frame:0 TX packets:694246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:493539292 (493.5 MB) TX bytes:235159393 (235.1 MB) wlan1 Link encap:Ethernet HWaddr 00:c0:ca:42:14:62 inet addr:192.168.100.102 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:caff:fe42:1462/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:171053 errors:0 dropped:0 overruns:0 frame:0 TX packets:181363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:74094659 (74.0 MB) TX bytes:59474204 (59.4 MB) iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off wlan1 IEEE 802.11bg ESSID:"Zia" Mode:Managed Frequency:2.412 GHz Access Point: 00:0D:F0:9C:A6:18 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-31 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:204 Invalid misc:6610 Missed beacon:0

  Read the article

• Packard Bell TK11 Wifi not working (Ubuntu 12.10)

  - by Ingmar

  Hardware: Packard Bell EasyNote TK11BZ, BIOS version 1.15 Broadcom BCM43227 802.11 b/n/g Problem: Everything works as it should, except the wireless connection. The Wifi device is enabled in the "Additional Drivers" section of Software Sources, but does not even show up in the network manager drop-down. sudo lshw -C network: *-network UNCLAIMED description: Network controller product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0100000-f0103fff

  Read the article

• BCM 4306 not recognized after upgrade on a Dell Latitude D600

  - by Brian Eisemann

  This is extremely frustrating to me. I had the wireless card working before I upgraded to 11.10. At first the wireless device was recognized but it told me there was no firmware, so I went ahead and went through the process I did before of installing the b43/b43legacy firmware, and now my wireless device is not even recognized, or showing up anywhere! 02:03.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11a/b/g [14e4:4324] (rev 03)

  Read the article

• Les commutateurs HP E-Series à économie d'énergie intègrent le nouveau standard IEEE et diminuent le coût total de possession de 51 %

  Les commutateurs HP E-Series à économie d'énergie intègrent le nouveau standard IEEE et diminuent le coût total de possession de 51 % HP a annoncé le 6 janvier l'arrivée de ses premiers produits fondés sur un nouveau standard Ethernet à haute efficacité énergétique. Un standard que HP se félicite d'avoir aidé à développer, et qui permet aux entreprises de réduire la consommation énergétique et les coûts opérationnels des équipements IT. Le standard Ethernet à haute efficacité énergétique de l'IEEE (IEEE 802.3az) ajustant la consommation automatiquement en fonction du trafic réseau effectif entre les commutateurs et les autres équipements connectés au réseau, et ce, en temps réel.

  Read the article

• iwconfig, iw not displaying wireless information

  - by Srivatsa Kanchi

  after fresh install to 12.10, the wireless information is not shown by both iwconfig and iw. The wireless sets up successfully and able to connect This is what i get $ iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ iw wlan0 link Not connected. $ uname -a Linux srivatsa-ThinkPad-T61 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Wireless Lan driver for Toshiba Satellite C850-A823 PSKCCV-02300XAR

  - by user111942

  I have Toshiba Satellite C850-A823 PSKCCV-02300XAR Laptop, i had installed Ubuntu 12.10 as dual boot (windows 7 already working), after the installation i had noticed that wireless driver not installed in ubuntu 12.10, from windows device manager i got details of wireless lan driver as follows "Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC" i dont have LAN cable connection, kindly help me how to get wireless driver and install in ubuntu 12.10 hoping for your kind support shiyas

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >