Search Results

Search found 4248 results on 170 pages for 'adsl router'.

Page 8/170 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• How does Router know where to forward packet

  - by kornelijepetak

  If several computers with local addresses (192.168.0.#) are connected to a router and each computer opens a web browser and requests a page over HTTP, when these TCP:80 packets are sent out, the router switches the local address with the static IP of the router (i.e. Provider given IP) so the server can reply to the appropriate address. But how does the router know to which computer to forward the HTTP reply, since the TCP header does not contain the local IP address (does it?), and all computers are using port 80? Does this have anything to do with the MAC addresses? How exactly does this work?

  Read the article

• How to set up wireless access on a Cisco router

  - by Carlos

  Hi, I've set up my 877W according to the configuration listed in this forum post: IPTV over Cisco 877 (It's the working configuration at the bottom of the post) Note that I have an 877W, so it also has a wireless radio. Now, I've gotten the whole setup to work, so IPTV is working, and I can access the internet via the ethernet ports. Now I'm trying to figure out how to allow access via the dot11radio interface. I've gathered that I basically need to create a bridge group, and bridge the radio to the internet VLAN. However, when I add a bridge-group 2 command to VLAN1, it seems to take down the whole internet VLAN. (The IPTV continues to work.) This makes the router itself inaccessible (I've got a laptop, so no serial) and I end up having to reboot the router. Can anyone tell me how to a) Allow wireless access to the internet (preferably with WEP, to match my old router) b) Determine what makes the router inaccessible when I add the new bridge group c) Forward the IPTV traffic onto a machine on my internet VLAN

  Read the article

• Should I Upgrade My Old Wireless Router?

  - by lyngbym

  I have an old wireless router, and I mean stone age old (5 years). There is nothing wrong technically with the router, it serves my wireless needs at home but it is really darn old. A search on Belkin's site for F5D7230-4 actually turns up a different old model so I scrounged up this old review for you to get a sense of what I'm running: http://www.pcmag.com/article2/0,2817,1572451,00.asp. Is there a valid security reason to replace this router in 2009? Google searches have turned up a few security threats to it and Belkin hasn't released new firmeware in years for it. I am starting to think I should replace it mainly because its NAT is about the only thing protecting me from the outside world. Buying a new wireless router is a boring way to spend money since it just sits on a shelf doing its job. Thoughts?

  Read the article

• Router drops internet connection if I connect an additional pc

  - by BluePerry

  Hey, I'm using a SMC2804WBRP-G router connected to my ADSL-modem. Usually there are two computers connected to this router: a win7 ultimate desktop(wired) and a macbook air (wireless). Both working absolutely fine and never caused any connection drops as far as I know. A new room mate moved in last month and each time she starts up her win7 home laptop the router looses the internet connection. The laptop is on a wired connection. The first time she connected to my router, the connection dropped every 2 mins. To find out whats wrong with her machine I disabled all unnecessary services etc. besides the anti virus software. That helped to eliminate almost all of those periodic connection drops. But the start up drop remained and I've got the feeling that the router is still loosing connection from time to time. I haven't had the time to find out what service caused the periodic drops. But I'm more concerned about is that start up drop. Can anyone point me in the right direction to look for the problem? I would be very thankful for any hints or tips!

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• Router which can modify TTL

  - by TheMouse

  My ISP has set up the TTL to 1. My current router Linksys WRT120N can't change this and my computers don't have connection to Internet. I will return my current router and take another. I have some options: D-Link DIR-615 D-Link DIR-320 Linksys WRT54G2 Linksys WRT54GL Is the last router the only fix (among these routers) to my problem? ( I have to buy the router from this shop: http://laptop.bg/#/accessories/routers/ .. the site is in Bulgarian but at least the models which I can choose from are there in English.)

  Read the article

• 2wire modem to linksys router

  - by Imajica666

  I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

  Read the article

• Trouble opening my router to my web server

  - by Justin Heather Barrios

  Here's the story. I have a webs server created and connected to my router. The website works great when I'm connected to the router, but when I'm off the network I can't access the website. I got the IP for my router by googling "what is my ip." I have opened ports 80 to 10080 to link to the server in the router. One odd thing that I don't understand. When I am in network if I access XXX.XXX.XX.XX:80 I can access the web page no problem. If I access XXX.XXX.XX.XX:81 (or any other port) I get the error "Cannot access server." Any idea what the problem could be? Could it be my ISP?

  Read the article

• Reliable router with good VPN and WAN Throughput [closed]

  - by Asdande

  I have 2 cisco rv180 VPN router. These routers are giving me lots of problems. The webpages wont load correctly, slow response to load webpages plus other many issues. I have several cases pending with cisco. I give up on these routers. I would like to know if you guys can recommend me a reliable router for our 3 branches (NY - main, SC and FL). In NY- main office, we have 55 users. In SC branch, 6 users. In Florida we only have 1 (will grow soon). I need a router capable of support: 3 VPNs Site-to-Site connection VPN throughput of at least 40-50 Mbps WAN throughput at least 100 Mpbs and up PPTP Server for at least 5 PPTP users Web filtering - all users need access to internet Good Firewall Port forwarding for FTP Server - able to show the public IPs of FTP users (rv180 cannot do that, just shows me router's LAN interface IP, opened a case with cisco, now escaleted to level 2, still no answer or workaround) Dual WAN ports for balance or backup internet. Gigabit WAN/LAN ports Price between $400-$500 range. I was thinking on the TP-LINK TL-ER6120 or TL-ER6020 according to the review on smallnetbuilder.com http://www.smallnetbuilder.com/lanwan/lanwan-reviews/31983-tp-link-tl-er6020-safestream-gigabit-dual-wan-vpn-router-reviewed but I don't want to make another mistake as I did when I bought the cisco RV180. Thank you in advance,

  Read the article

• Can't connect my 3G to home router umbrella

  - by Cindi

  I can't connect my 3G iphone to my home router. I added my MAC wifi address (followed those directions to locate it) to the filter of the router. My iphone wifi address appears on the allowed list. However, when I try to connect using my iphone, it shows wi-fi not connected, and the umbrella corporation comes up still locked and asks for a password. We don't have a password set up for our router access at home. I'm not real tech-y so speak plainly...thanks

  Read the article

• VPN Router + LDAP/RADIUS?

  - by MrZ

  Hello all! I need a VPN-capable router, preferably with a web interface, that should be able to authenticate against my LDAP server which is behind the router. The problem stems from the fact that I'm utterly unable to configure that setup for the Linksys RVS4000 that I own. Anything exists that is both cheap and easy to setup? Flashing the firmware is an option, as long as it is a well-documented option. Would it be viable/doable? [Edit] Okay, I've been looking at custom firmwares, any way to know which ones will work with my router before nuking its present one to oblivion? Anyone has experimented with that? My needs are quite simple, I want a DHCP router, an LDAP authenticated VPN, and basic firewall capabilities. I'm using DynDNS from the RVS4000 for now, but I guess I could setup something on the servers instead, that's only a minor problem...

  Read the article

• Setting up Multiple Routers (as Hardware Firewalls) behind a Home Router

  - by Synetech

  I’ve currently got one computer behind a router with built-in firewall functionality, connected to a home cable-modem that has a single Ethernet port and one IP. I’m going to have to set up another computer for the rest of the family to use which of course will need to be connected to the Internet, probably wirelessly since the modem is in my room and the new system would not be. What I would like to do is to get two more small routers with firewall capability and connect each computer to a router, which would in turn connect to the main router which connects to the cable-modem. That way, both systems have a hardware firewall protecting them (particularly the wireless system) and the burden of blocking would be reduced on both the computer CPUs and the main router because the secondary routers would handle some of the workload. I’m trying to find out about the complexities inherent in this design and how I could set it up to work, specifically the IP handling and NAT aspect. Thanks a lot.

  Read the article

• Multiple IPs from one router

  - by ergoen

  I would like to know if it is possible (and if so, how) to configure a router running dd-wrt (or openwrt) to supply connected devices with two ip addresses. The network looks like this: [Internet] | [Router] | | [Comp1] [Comp2] ... My ISP provides me with enough public IP adresses to give all devices on my network one each. The easiest way to set that up is to just use the router as a switch. This will however lead to problems with some LAN based applications. I would still like to use Samba-shares between the computers as well as a vpn server. What I am looking for basically is if it is possible to use the router as a DHCP server for a local network (let's say giving IP adresses 192.168.1.xx to connected computers) while at the same time passing through public IP addresses to each as well?

  Read the article

• A switch and router between the printer and PC that want to print but cannot

  - by Robert Memo

  IP 192.168.1.5 has a wireless connection to a Linksys router (192.168.1.1) which then is connected to a switch. The switch is connected to a server (192.168.0.2). My printer has IP address of 192.168.0.8. Internet connection is fine on 192.168.1.5. Problem 1: IP 192.168.1.5 can not print using printer 192.168.0.8. Problem 2: IP 192.168.1.2 can not access a shared folder on the the server. The reason for connecting this way is that, the server does not release wireless signal. In order to get wireless signal the Router is connected to the switch. The server is a computer server that only has one outgoing LAN port. Plus, due to inconvinience physical locations, I do not have option to change the physical locations and the way it is connected already. I just want the labtops that only have wireless connection to communicate with the printer and the server. I have tried to change the router IP address to 192.168.0.x like the server and printer. It caused problem for the laptop. The router no longer release internet signals. The router does have IP address from the server 192.168.0.5.

  Read the article

• QNAP (469L) with Debian: can't connect to router

  - by agtoever

  I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

  Read the article

• Connect a Sitecom WL-174 to another wireless router

  - by Thijs Wouters

  I used to connect via a Sitecom WL-174 directly to ADSL internet. There were some pc's which connected wirelessly and some connected with a wire. Now we got another provider and we need to use the router which came with it. It is also a wireless router. It works perfectly. But I need to connect the other pc's which were connected with a wire previously. Is it possible to connect the Sitecom router wirelessly to the other router? If so, how? Thanks.

  Read the article

• D-Link wireless router losing outbound data

  - by gsteinert

  I have a Linux box running the Apache web server behind a D-Link wireless router (nothing fancy, just standard kit that comes with Virgin Media broadband). My issue is that when requesting web pages (from within the network or via the web), the back end of the page seems to be being dropped. For example, I tried to display a text-only file, and all I could get was the first 40-70% of the file (it changed slightly with each refresh). The apache access logs show that only part of the data was being sent (~6000 bytes instead of the 12000+ bytes of the file). Removing my router from the equation fixes the issue and I can download any files no matter the size with no problems. My theory is that the uploaded packets are either being dropped or held up by the config of the router. Is there anything I can do to alleviate the problem? (Perhaps a way of reconfiguring the router to upload packets harder/better/faster/stronger or an option in apache that provides a workaround) As a last resort I will get a second NIC for my Linux box and turn it into a router, but that would mean the box will be on 24/7... not the most ideal of circumstances. Gary

  Read the article

• Home router for higher network loads

  - by Zizzencs

  I'm trying to find a replacement for my ASUS WL500GP router. Some constraints: my ISP now provides 120 Mbit bandwidth - the router must be able to handle it I have 3 computers and a laptop at home - the router must have at least 4 LAN ports and the WAN port I need to be able to do the following in parallel: use bittorrent with ~1000 connections transfer files from one home computer to another at high speed access one home computer from my workplace I don't really need wireless I don't really want two boxes to serve all these purposes. So I was searching for a router with 1 Gbit ports, jumbo frame support and good reviews, but haven't really found a promising candidate so far. Any suggestions?

  Read the article

• How do you know if a router is good for 50 computers

  - by Wilson Besong

  My Router is not wireless and I don't wish to use wireless for my own security, I have a Bandwidth of 1024/512 mbps, but my connection drops still. People talk of my router. How Do I Know a ROUTER is good for me to connect 50 Clients.

  Read the article

• Router Suggestions [closed]

  - by zamN

  Lately I've been having router problems with my Linksys WRT54G when it comes to signal strength. Anyways I am thinking of getting a new router since the linksys is about 5 years old now. I'm just curious what router to get because I want to get the most out of my money. I already have a modem that I will connect to the router. I don't need voIP or any of that. All I simply want is just something that is going to last and will not have any stupid problems.

  Read the article

• Can I share my cable internet connection through my ADSL wireless router?

  - by Roaders

  Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

  Read the article

• DD-WRT (WRT54G) and (THOMSON TG782) how to put them togather?

  - by FeRtoll

  Ok so let me explain, i bought WRT54G and successfully installed DD-WRT v24-sp1 (07/26/08) mini-special - build 9994. That's all ok no problems with it all normal functioning. And just to add (i don't need wireless, wireless is turned off always) What i want: ISP's router (TG782) from it's INTERNET port(out) cable "which was before in my pc" is connected to WRT54G's INTERNET port and then from WRT54G LAN port 1 to my pc. The problem: How do i connect and setup all? I have tried many times on many different ways but cant get it to work IF THE CABLE FROM TG782 IS CONNECTED TO WRT54G ON INTERNET PORT. If i connect the TG782 to Lan port 1 on WRT54G and my pc to lan port 2 then all works fine after i setup gateway and all. But i want to connect TG782 to Internet port of WRT54G because i need "Access Restrictions" and this only goes through WAN right? please correct me if i am wrong. What i have tried: This is how i have tried to setup all. The TG782 router ip is 192.168.1.1 And WRT54G ip is 192.168.1.30 so in WRT54G control panel i have setup like this: ----WAN Connection Type---- Connection Type: Automatic Configuration - DHCP STP: Disabled ----Router IP---- Local IP Address: 192.168.1.30 Subnet Mask: 255.255.255.0 Gateway: 192.168.1.1 (the TG782) ----Network Address Server Settings (DHCP)---- DHCP Type: DHCP Server Start IP Address: 192.168.1.100 Maximum DHCP Users: 6 And this wont work i probably miss something more, if anyone can help i would be thankfull. Also i have to note that i have tried to set my network adapter on pc to use the gateway of WRT54G and ip 192.168.1.102 In short: i cant get it to work normal only as a switch! Thanks for any help! -------EDIT:------- Here is an image which maybe can help: http://img27.imageshack.us/img27/4227/allin1w.jpg

  Read the article

• Router not connecting to the internet

  - by Peter

  I had a weird problem this morning with my router - it's an Alice Gate VoIP 2 Plus WI-FI - not connecting to the internet after more or less 1 hour online (I'm always connected with the ethernet cable). The led status lights for Power, WI-FI, ADSL, Internet, Service should be on in order to be connected and navigate online. The problem was that the leds ADSL, Internet were off and I did not know why because it never happened before. I looked at the stats in the settings and the numbers for Bytes/Packages for both Sent/Received were there and increasing but I couldn't connect to the internet. I called tech support, they checked and told me to keep the router on for 48 hours because they were checking it. I've reset it twice before and after I called tech support and it still did not work so after about 2 hours of waiting I tried connecting using WI-FI and the leds 'magically' turned on, first the ADSL and Internet(Internet led always turns on last). At this point I'm curious what could of caused this and I'm doubting that the tech-support guys did something. What could of been the problem with the ethernet cable not connecting in the first place? It always works. What do the tech support guys normally do when they tell me to keep the router on so they can 'check it'? PS: I'm using ubuntu 32 bit

  Read the article

• System and Router configuration for setting up a home firewall based on Zentyal

  - by Ako

  I am not much of a system administrator, so please be patient if this looks too simple for you. I have a several computers at home, and all of them connect using an ADSL modem/router (and Wireless AP). I have been attacked several times (mainly from Russia and Ukraine), so I thought I should have some kind of firewall, besides the ESET firewall on my Windows 7. So now I have these (new) configuration: I have a small ADSL modem (Zyxel brand) which has only one Ethernet port. This modem is used to connect to internet and is configured in NAT mode. The interface has is configured with IP address 192.168.1.1. I have an old PC and I have installed zentyal on it. It has two Ethernet ports, eth0 and eth1. Eth0 is connected to the Zyxel modem with IP 192.168.1.2 and is checked as the WAN interface (external). I have another ADSL modem which is also a router with 4 Ethernet ports and Wireless AP. One of the Ethernet ports is connected to eth1 on Zentyal box. The Ethernet port's IP is 192.168.2.1 and Zentyal's eth1 is 192.168.2.2. Now, I want to enable other computers to connect to internet through the router both using Wireless and Ethernet. The problem is that I don't know how to configure the router so it routes connections to the Zentyal box. Does anyone have any clue? Again I am sorry if this looks stupid. Thanks.

  Read the article

• MTU, DSL router and stalling TCP

  - by user38843

  I am discovering stalling TCP connection problem. The problem arises when I try to scp stuff from remote system from my home network. My home network is connected to internet via PPPoE (ADSL+) and everything works perfectly once working from my home network. The ADSL router has MTU set to 1492 but with that setting the scp from remote system does not work - stalling! When I change the MTU on my router to 1500 the that scp works perfectly but internet accesses from my home network is very slow to most of the www sites - even local ones. Just wondering where the problem exists - my ISP blocking ICMP, etc? Thanks!

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >