Search Results

Search found 1492 results on 60 pages for 'dan goldstein'.

Page 8/60 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• Unable to keep the connecting using a wireless bridge

  - by dan

  I am running Ubuntu 12.04 on a dell inspiron desktop (core 2 duo) and am using wicd to manage my network/wifi. I've found that the WiFi card in the machine has trouble staying connected to my router (I believe this is a function of distance between the two), so I've taken an old Belkin F5d7231 wireless router and installed dd-wrt on it to use as a wireless bridge hoping that it will have better reception. I think everything up through the wireless bridge is working OK since I have no problems accessing the internet through it with my MacBook. The problem arises when I try to hook the ubuntu machine up to the wireless bridge. It will connect for a few minutes, but it will quickly disconnect without clear triggering event; it may be more likely to disconnect if there is a heavy traffic load going over it (could be something as simple as "cat big_text_file" in an ssh session). I've tried switching from dhclient to dhcpcd without much improvement. Here is the output from the syslog when it connects: Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: exiting Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: exiting Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:10:08 Chicabuntu kernel: [15184.976127] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.010805] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: exiting Jun 30 17:10:08 Chicabuntu kernel: [15185.180156] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.212785] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:10 Chicabuntu kernel: [15187.027445] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:10:10 Chicabuntu kernel: [15187.027452] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:10:10 Chicabuntu kernel: [15187.028300] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: dhcpcd 3.2.3 starting Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: hardware address = 00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: DUID = 00:01:00:01:17:81:85:79:00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: broadcasting for a lease Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:10:20 Chicabuntu kernel: [15197.568016] eth0: no IPv6 routers present Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: offered 192.168.1.111 from 192.168.1.254 Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: checking 192.168.1.111 is available on attached networks Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: leased 192.168.1.111 for 86400 seconds Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding IP address 192.168.1.111/24 Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding default route via 192.168.1.254 metric 0 Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: exiting Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv4 for mDNS. Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Registering new address record for 192.168.1.111 on eth0.IPv4. Jun 30 17:10:30 Chicabuntu dhcpcd.sh: interface eth0 has been configured with new IP=192.168.1.111 Jun 30 17:10:39 Chicabuntu ntpdate[28439]: adjust time server 91.189.94.4 offset 0.001915 sec And here is the syslog from when it shuts down the connection without reason: Jun 30 17:12:15 Chicabuntu kernel: [15312.575455] tg3 0000:3f:00.0: eth0: Link is down Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: sending signal 1 to pid 28361 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: received SIGHUP, releasing lease Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: exiting Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for 192.168.1.111 on eth0. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing default route via 192.168.1.254 metric 0 Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: No such process Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing IP address 192.168.1.111/24 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: Cannot assign requested address Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: exiting Jun 30 17:12:16 Chicabuntu dhcpcd.sh: interface eth0 has been brought down Jun 30 17:12:17 Chicabuntu kernel: [15313.612141] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.644703] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: exiting Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: exiting Jun 30 17:12:17 Chicabuntu kernel: [15313.912147] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.944746] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:18 Chicabuntu kernel: [15315.592569] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:12:18 Chicabuntu kernel: [15315.592576] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:12:18 Chicabuntu kernel: [15315.593399] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:12:29 Chicabuntu kernel: [15325.680019] eth0: no IPv6 routers present If this isn't useful, I can also post the wicd log, but that is kind of long. If anyone could help me I would be eternally grateful.

  Read the article

• I have permanent connections to Canonical servers, what are they for and how can I turn them off?

  - by Dan Dman

  After the recent upgrade to 12, I notice permanent connections to canonical servers. Running netstat -tp gives: Foreign Address State PID/Program name mulberry.canonical:http CLOSE_WAIT 6537/ubuntu-geoip-p alkes.canonical.co:http CLOSE_WAIT 6667/python alkes.canonical.co:http CLOSE_WAIT 6667/python Why are there permanent connections and how could I stop this behavior? And if this is intentional, who is responsible? I would like to understand why this was done because to me it seems like a bad idea.

  Read the article

• 3d vertex translated onto 2d viewport

  - by Dan Leidal

  I have a spherical world defined by simple trigonometric functions to create triangles that are relatively similar in size and shape throughout. What I want to be able to do is use mouse input to target a range of vertices in the area around the mouse click in order to manipulate these vertices in real time. I read a post on this forum regarding translating 3d world coordinates into the 2d viewport.. it recommended that you should multiply the world vector coordinates by the viewport and then the projection, but they didn't include any code examples, and suffice to say i couldn't get any good results. Further information.. I am using a lookat method for the viewport. Does this cause a problem, and if so is there a solution? If this isn't the problem, does anyone have a simple code example illustrating translating one vertex in a 3d world into a 2d viewspace? I am using XNA.

  Read the article

• My computer stops seeing the other computers on my network

  - by dan

  I'm running Ubuntu 11.04. Sometimes my computer stops seeing the names of the other computers on my network. So I can no longer log into another computer by typing the hosting name e.g. ssh [email protected] I can still log in using the local network IP address. How can I get the first way to work again without rebooting? I know this problem is local to the computer. The other computers on my network can still see one another. But they can no longer see the computer I'm working on, not even by local ip address.

  Read the article

• The Oldest Big Data Problem: Parsing Human Language

  - by dan.mcclary

  There's a new whitepaper up on Oracle Technology Network which details the use of Digital Reasoning Systems' Synthesys software on Oracle Big Data Appliance.  Digital Reasoning's approach is inherently "big data friendly," as it leverages multiple components of the Hadoop ecosystem.  Moreover, the paper addresses the oldest big data problem of them all: extracting knowledge from human text.   You can find the paper here.   From the Executive Summary: There is a wealth of information to be extracted from natural language, but that extraction is challenging. The volume of human language we generate constitutes a natural Big Data problem, while its complexity and nuance requires a particular expertise to model and mine. In this paper we illustrate the impressive combination of Oracle Big Data Appliance and Digital Reasoning Synthesys software. The combination of Synthesys and Big Data Appliance makes it possible to analyze tens of millions of documents in a matter of hours. Moreover, this powerful combination achieves four times greater throughput than conducting the equivalent analysis on a much larger cloud-deployed Hadoop cluster.

  Read the article

• Unity not running on startup

  - by Dan

  OK, so Firefox was running extremely slow, I ran it in safe mode and still slow, so I rebooted and when she came back on, I wasn't at the regular Unity login, it was like a classic Windows login (where I had to enter my username and password manually, not a list of users). I logged in and only my desktop was visible (with icons and my wallpaper). Nothing else. I was able to open a terminal with Ctrl+ Alt+T and typed... sudo unity ...which got it up (albeit with the default icons on the launcher ex. I had unlocked Libre Office and it was back). In "Startup Applications..." there was absolutely nothing at all... This happens every time I reboot. Thunderbird de-synced from my Gmail but Pidgin is still connected. When I do Ctrl+Alt+L it locks the screen as normal, but I have no option to switch user. I have the only account on this computer but I cannot access the main login screen to get to my Guest account. I'm not very Ubuntu-savy, but it's pretty clear that I'm starting in some sort of safemode. I am on a fresh install of Ubuntu 12.04.1 LTS (just installed it last night).

  Read the article

• Email links open in a new window [closed]

  - by Dan

  I'm asking this as an opinion question. How does everyone treat email links opening in a new window if their default email client is web based? This way? <a href="mailto:[email protected]">email me</a>. It will open fine for app based email clients but open in the same window for web based clients. This way? <a href="mailto:[email protected]" target="_blank">email me</a>. It will open in a new tab for web based email clients but open a blank tab. I cant really seem to find the best of both worlds. What does everyone else do?

  Read the article

• Does Bing support anything like Google's First Click Free program?

  - by Dan Fabulich

  Google has a program for webmasters called First Click Free. To implement First Click Free, you need to allow all users who find a document on your site via Google search to see the full text of that document, even if they have not registered or subscribed to see that content. The user's first click to your content area is free. However, once that user clicks a link on the original page, you can require them to sign in or register to read further. The user must be able to see the full content of a multi-page article. You can allow this by displaying all content on a single page to both Googlebot and users. Alternatively, you can use cookies to make sure that a user can visit each page of a multi-page article before being asked for registration or payment. Does Bing support anything like this?

  Read the article

• How to effectively use an overseas SEO team?

  - by Dan Gayle

  My company is currently in contract with a 20+ person team in the Philippines, previously used for comment linking and guest blogging spun content articles. This is a practice that we're stopping, but we don't want to sever our team because they work hard, they're really cheap, and they produce excellent accounting and reporting of their actions. What are ways that we can best put them to use as a link generating or content generating resource? Their English is fair, but not of high enough quality to use them for any direct content creation. Thanks

  Read the article

• QA & Testing with UPK

  - by dan.gallo(at)oracle.com

  Most customers know that UPK produces both the word and excel based test scripts for UAT. Did you know that you can use UPK for QA review and bug tracking? To use UPK for QA, create content and assign it appropriately to authorized reviewers. Then have them open the developer, use customized views to find content assigned to them quickly and check out the topics. Then they can use the topic editor to review the content and provide comments right into the bubbles or use explanation frames. It makes QA-ing content this way easier than publishing and sending out .tpcs or docs for people to review. How about UPK for bug tracking? The hardest part about fixing bugs in software is reproducing the error! When you use UPK for bug tracking, it captures the exact steps the user took that gave them the error. Now development can easily walk through the process in a simulated environment to see what might have caused it, they have a documented procedure for what generated the error and they are able to better communicate with the LOB. Also, they can update or attach the simulation\documentation to any defect management software like bugzilla or something similar -all thanks to UPK.

  Read the article

• What does intermittent "Input/output error" suggest?

  - by dan

  Lately my Ubuntu 12 system has started acting very strange. Sometimes the computer freezes and then unfreezes 2 minutes later, and other times when I try a basic command like less I get the error bash: /usr/bin/less: Input/output error. But this is intermittent too. Any suggestions? Also if I try sudo reboot and enter my password, I get sudo: unable to open /var/lib/sudo/plato/7: Read-only file system Before I used to be able to do sudo reboot fine. If I tail /var/log/syslog I do see these curious lines: .... ata1: softreset failed (device not ready) .... ata1: hard resettting link .... ata1: link is slow to respond, please be patient (ready=0) What can I do to fix this?

  Read the article

• Time jumping forward on NTP failure

  - by Dan

  I have been having some weird problems with NTP for a while. If I use ntpdate to set the time then it sets fine. ntpd then invariably fails to find a server (I have loads configured) and decides to set the clock forward about 5 hours. It's a Xen server with dom0 set to a different timezone so I'm not sure if that is interfering with it. How can I make sure I ignore the dom0 time and have ntpd not change the time if it fails to reach a time server? EDIT: I now do not think it is ntpd giving me problems, I turned ntpd off and it jumped forward seemingly randomly.

  Read the article

• To what extent do code-signing certificates boost sales of your software?

  - by Dan W

  In the experiences of everyone here, have you found a certificate to boost sales of your (downloadable) program? I produce .NET software and upon clicking the installation file, Windows 7 pops up a message saying the software is from an "unknown publisher" and to proceed with caution. For Windows 8, this appears to be even more prominent, and may adversely affect the number of downloads, and therefore the number of sales. A certificate will help soften this 'warning' by (for example) changing the warning's colour from orange to blue, and give the publisher's name instead of 'unknown'. But I'd like more tangible evidence since many people are obviously used to that message, and may not care and download anyway. So has anyone noticed a jump in sales after the switch?

  Read the article

• My server is behind a router. How can I see my website correctly? [closed]

  - by Tokyo Dan

  I'm running a web server (Ubuntu) on my local home network. I'm behind a router. On the WAN I have a direct IP. When not on my home network and accessing my website via the WAN direct IP my website displays correctly and everything works. On my home LAN behind the router, accessing my website via the WAN direct gets me to my router's admin login page. This is normal. But... Accessing my website (via it's home LAN IP address) from another computer on my home LAN gets me to the website but the layout display is broken and clicking on any link takes me to the WAN direct IP (my router's Admin login page). How can i get my website to display properly and the links to work when accessing it from my home LAN?

  Read the article

• Strategy for building an application to replace a large spreadsheet

  - by Dan Walmsley

  I'm working on an application that is going to replace a rather large spreadsheet. The spreadsheet is used to budget purchases and things like that. It is the largest spreadsheet I have ever seen, and it required a lot of manual data entry, so this application is going to automate much of that. But as I'm working on this I've noticed its slow going. And I got to thinking this must be a common thing to do many companies will start with something like a spreadsheet, then when they get too big to maintain that, they will get a custom application built. So is there anything out there ( a framework or similar ) that does this sort of thing, migrating a spreadsheet to a custom application. I've had a quick Google but not really seen the kind of thing that I'm looking for. It's too late for this project, but I thought it would be worth having a look for next time. How do you guys tackle this problem?

  Read the article

• Does something like this "dream" online IDE product exist?

  - by Dan Tao

  I was thinking the other day, it would be amazing if a web-based product with the following features existed: Customizable text editor with nice formatting like ACE Real-time collaborative editing like Google Docs (or the late Wave) Online multi-language compiling capabilities like Ideone.com SCM hosting and/or integration + issue management like... oh, I don't know, GitHub Clearly (considering the examples), all the desired features exist. Is there anywhere that they exist all in one product? If not, does anything come close?

  Read the article

• No sound after installing a new Graphics Card

  - by Dan

  I've just upgraded my graphics card to an Asus Geforce 210 and now my system has no sound. I've ran Update Manager and the Additional Drivers utility which installed the latest Nvida driver. The graphics card is connected to my TV via a DVI-to-HDMI (DVI at the PC end) cable for the visual connection, and an audio jack from my onboard soundcard for my audio connection. Any ideas on how to resolve this? I ran this command ubuntu-bug audio And it outputted this: You seem to have configured PulseAudio to use the "pci-0000_05_00.1" card, while you want output from "NFORCE - NVidia CK804". I've tired a bit of messing about with the audio settings but can't get anything to work.

  Read the article

• upgrade from ubuntu 13.04 to 13.10 causes vmware workstation 9 problems

  - by dan

  so, upgrade caused problem where running vmware ws 9 needed patches to accommodate linux kernal 3.11. I applied those fixes I found that others reported, and now i can only run vmware ws 9 from sudo. If i run it from standard user, it says it wants to recompile modules, which it does not do unless I open up a terminal and run sudo vmware. that works, but would like it to work correctly, have the modules that are recompiled stick. when running under sudo vmware, it does recompile with errors.. (vmware-unity-helper:13019): Gtk-WARNING **: Unable to locate theme engine in module_path: "murrine", and starts up and works ok. any ideas? thanks for any help you can provide

  Read the article

• Looking for suggestions: becoming a hireable, young programmer [closed]

  - by Dan

  I am a 17 year old Java programmer that has filled the last year with learning all of the ins and outs of Java - Using Eclipse, and the help of a friend of the family (a Java programming architect for some company), I have learned everything from serializing objects, basic networking, generics, reflection, multi-threading, code optimization and efficiency & some concurrency safety - built my own proxy class, and nowadays, I answer questions on Project Euler. I am seeking some suggestions though on where I go next, or where I go from here to get a job in programming. I dedicate at least an hour every day to coding, sometimes literally, the entire day, and I really have come to love the process. I just started reading Effective Java (v2), and learning Scala (as I see often, possibly the Java replacement) I will be going to college for Computer Science next year - and taking AP computer science this year (however, I took a practice exam and got an 87, only need a 60to70 to pass, so no need to study for it too much) -- I was wondering if getting the SE 7 OCA and OCP would help me in trying to get a programming job. I looked around and most people have said online that an OCA/OCP are practically useless, but, at my age do they make me any more credible? More or less, what would you recommend to get a job in programming these days - or distinguish yourself from the crowd? I have enough time and dedication to learn another language, or anything really. Thank you very much.

  Read the article

• Lightning fast forum based around metadata / tags? [closed]

  - by Dan W

  Possible Duplicate: What Forum Software should I use? I wonder if anything like this exists. I'd like to add a forum to my site, but instead of the usual forum/subforum/sub-subforum structure, I'd like to use a metadata/tag approach where everything exists as a single directory, and where there's a search field at the top which instantly (<0.5 sec) filters the threads to a particular keyword or keywords. Also, as the admin, I would be able to add highly visible buttons at the top, which can be clicked on for the main categories I choose for the forum (nevertheless, users can also add tags to their own threads outside of these default main tags I supply if they wish). This approach, if done properly, is more powerful, efficient, maintenance free, scalable and friendly than a standard forum, so I was hoping someone had the same idea and made something out of it. It couldn't be that hard. I'd want the speed to be up to (or near) the standard of this: http://forum.dlang.org/ Other forums (e.g.: phpBB) are orders of magnitude worse than that in terms of latency (posting or browsing), and I think that is wrong, even in principle ;)

  Read the article

• multiple godaddy domains to home router then reverse proxy to multiple internal servers [closed]

  - by Dan

  I need someone to steer me correctly... advising on all required components. I have multiple domains with godaddy, say site1.com , site2.com, site3.net I have multiple home LAMP servers... one on say, lampsrv1 = 192.168.0.2:8080 (windows) and lampsrv2 = 192.168.0.3:9080 (linux srv2) I would like to have server1.site1.com point to lampsrv1 and server2.site1.com point to lampsrv2 . I may also want server1.site2.com also point to my lampsrv1 as an option. My thinking is - I have a dedicated linux srv1 with a reverse proxy server behind the router, ie Apache or NGINX or equivalent directing to appropriate LAMP server. It's the godaddy subdomains, cnames or redirections, etc I'm having a challenge with for starters... I have tested apache with virtual servers but can't get proxying to work based on host header info... seems to go to one address making me think its actually the apache reverse proxying that's not quite working. Finally to add to this, my router has a dynamic IP but does lease for quite a while but that would be my final piece. So, I'm sure this might be a popular question but can't seem to piece this together. I need someone who has actually configured this scenario to advise but will take other suggestions.... please indicate if you have successfully configured this.

  Read the article

• Do I need to uninstall Ubuntu after fresh Windows 7 installation?

  - by Dan

  I installed Ubuntu 12.04 from Windows 7 using Wubi. For reasons I won't elaborate here, I had to reinstall Windows 7. Now I want to uninstall Ubuntu. But there is no entry for ubuntu in Windows' Add/Remove Programs anymore. What I tried: running the Uninstall executable from Ubuntu's installation folder, which didn't do anything. delete the old installation folder No matter what I do Ubuntu continues to show up as a boot option together with Windows 7 whenever I start my machine. How do I completely get rid of the Ubuntu installation? Thanks.

  Read the article

• Producer-consumer pattern with consumer restrictions

  - by Dan

  I have a processing problem that I am thinking is a classic producer-consumer problem with the two added wrinkles that there may be a variable number of producers and there is the restriction that no more than one item per producer may be consumed at any one time. I will generally have 50-100 producers and as many consumers as CPU cores on the server. I want to maximize the throughput of the consumers while ensuring that there are never more than one work item in process from any single producer. This is more complicated than the classic producer-consumer problem which I think assumes a single producer and no restriction on which work items may be in progress at any one time. I think the problem of multiple producers is relatively easily solved by enqueuing all work items on a single work queue protected by a critical section. I think the restriction on simultaneously processing work items from any single producer is harder because I cannot think of any solution that does not require each consumer to notify some kind of work dispatcher that a particular work item has been completed so as to lift the restriction on work items from that producer. In other words, if Consumer2 has just completed WorkItem42 from Producer53, there needs to be some kind of callback or notification from Consumer2 to a work dispatcher to allow the work dispatcher to release the next work item from Producer53 to the next available consumer (whether Consumer2 or otherwise). Am I overlooking something simple here? Is there a known pattern for this problem? I would appreciate any pointers.

  Read the article

• What kind of website or coding is suitable and safe for an artist's website

  - by Dan S

  I have a web design project that is related to a singer, and I used Joomla for my previous project and designed good music websites. But for this project I cannot find a suitable template to edit and use. As the website is so simple and does not have any special functionality, I'm thinking about creating a website with just simple CSS, html and jQuery. I'm Good at them and can make a perfect look but I am not sure about the security. In Joomla I use different security plugins but do not know about a client-side scripting. So generally I need your ideas, about the following questions: - Is Joomla and generally CMS a good option for a music website? - How famous artists' website is base on? CMS or Client-side scripting? - Do you recommend to create it manually without using and CMS or template? - An do you suggest WordPress for this type of websites? (The website will have these pages: Biography, News, Music (with a music player), Photos, videos and contacts). That's it! Thank you for all your responds, I had a look at Joomla and the only template I chose is This One which seems very simple, and I am worry about module position, because it seems does not have any module position at all. I tried to contact the provider but did not get any respond. Does anyone know about its module position, I mean is there any way to find them? An is it possible to create a 2-3 module positions? Also I had a look at ThemeForest's WordPress templates and it has such a great template. I think WordPress is more active in creating artistic templates. But is it secure and professional to use this CMS for a singer who is kinda famous it his country? I am talking about a template like this. Share your opinions guys.

  Read the article

• I'm stuck on User Defined Session destop environment

  - by Dan

  I just installed Ubuntu for the first time dual boot so I get to choose Ubuntu or windows. I then changed the setting where is doesn't ask for my password when booting up. I then installed Edubuntu desktop package. I then hit system and logged out that way i could be at the loggin screen that also lets you select the desktop environment. Edubuntu was not there but User defined session was so i clicked that thinking that might be Edubuntu and logged in. Now im totally stuck. Only walpaper on the screen as i realize now that is normal for user defined session but there is no log out button to change desktop environments now and since I set it to not ask for password at boot up there is no option to change it at start up. If i hit ctrl+alt+del it only lets you shutdown, restart, suspend, or hybernate.... no logg out. I have hit every key on the keybourd hoping something will pop up. I thought this must be a simple noob mistake that there must be endless artiles about this so did searches on google and forums and was shocked to find nothing about this. My next step unless someone can help is to uninstall and reinstall.

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >