Search Results

Search found 2436 results on 98 pages for 'verify'.

Page 82/98 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• custom route not working on windows

  - by Michael Closson

  My windows laptop is directly connected to 192.168.1.0/24 (wireless lan). I access 10.21.0.0/16 though a router that is connected to both networks. The routing works fine with this configuration. I have a VPN, that connects to 10.0.0.0/8. The VPN network doesn't actually use any IPs in the 10.21.0.0/16 range. So I should be able to configure my routing table to route all the 10.21.0.0/16 IPs through the wireless lan, and all other 10.0.0.0/8 through the VPN. My understanding is that I can do this if the metric for the 10.21.0.0 is lower than that of the 10.0.0.0. The VPN (10.0.0.0) is automatically assigned metric 20. I have manually assigned the WLAN a metric of 1. I manually add an entry to the routing table with this command: route add 10.21.0.0 mask 255.255.0.0 192.168.1.201 metric 1 The route is then assigned a metric of 2 (which is expected). The problem is that it doesn't work. I can't ping any machine on the 10.21.0.0 network. But I can access other stuff on the 10.0.0.0. I can also access stuff on the 192.168.1.0. To debug this i've done the following. Run tcpdump on the router (192.168.1.201). I can verify that no packets for 10.21.0.0 arrive on that interface. Disable iptables on the router. Disable the windows firewall. Run wireshark on my laptop, to try and see which interface the ping requests go to. But I can't see them go anywhere!! The ping command doesn't receive any 'destination unreachable' messages. Here is the relevant section of the routing table. IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.201 192.168.1.18 2 10.0.0.0 255.0.0.0 On-link 10.55.44.203 20 10.21.0.0 255.255.0.0 192.168.1.201 192.168.1.18 2

  Read the article

• LUKS with LVM, mount is not persistent after reboot

  - by linxsaga

  I have created a Logical vol and used luks to encrypt it. But while rebooting the server. I get a error message (below), therefore I would have to enter the root pass and disable the /etc/fstab entry. So mount of the LUKS partition is not persistent during reboot using LUKS. I have this setup on RHEL6 and wondering what i could be missing. I want to the LV to get be mount on reboot. Later I would want to replace it with UUID instead of the device name. Error message on reboot: "Give root password for maintenance (or type Control-D to continue):" Here are the steps from the beginning: [root@rhel6 ~]# pvcreate /dev/sdb Physical volume "/dev/sdb" successfully created [root@rhel6 ~]# vgcreate vg01 /dev/sdb Volume group "vg01" successfully created [root@rhel6 ~]# lvcreate --size 500M -n lvol1 vg01 Logical volume "lvol1" created [root@rhel6 ~]# lvdisplay --- Logical volume --- LV Name /dev/vg01/lvol1 VG Name vg01 LV UUID nX9DDe-ctqG-XCgO-2wcx-ddy4-i91Y-rZ5u91 LV Write Access read/write LV Status available # open 0 LV Size 500.00 MiB Current LE 125 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 [root@rhel6 ~]# cryptsetup luksFormat /dev/vg01/lvol1 WARNING! ======== This will overwrite data on /dev/vg01/lvol1 irrevocably. Are you sure? (Type uppercase yes): YES Enter LUKS passphrase: Verify passphrase: [root@rhel6 ~]# mkdir /house [root@rhel6 ~]# cryptsetup luksOpen /dev/vg01/lvol1 house Enter passphrase for /dev/vg01/lvol1: [root@rhel6 ~]# mkfs.ext4 /dev/mapper/house mke2fs 1.41.12 (17-May-2010) Filesystem label= OS type: Linux Block size=1024 (log=0) Fragment size=1024 (log=0) Stride=0 blocks, Stripe width=0 blocks 127512 inodes, 509952 blocks 25497 blocks (5.00%) reserved for the super user First data block=1 Maximum filesystem blocks=67633152 63 block groups 8192 blocks per group, 8192 fragments per group 2024 inodes per group Superblock backups stored on blocks: 8193, 24577, 40961, 57345, 73729, 204801, 221185, 401409 Writing inode tables: done Creating journal (8192 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 21 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. [root@rhel6 ~]# mount -t ext4 /dev/mapper/house /house PS: HERE I have successfully mounted: [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# vim /etc/fstab -> as follow /dev/mapper/house /house ext4 defaults 1 2 [root@rhel6 ~]# vim /etc/crypttab -> entry as follows house /dev/vg01/lvol1 password [root@rhel6 ~]# mount -o remount /house [root@rhel6 ~]# ls /house/ lost+found [root@rhel6 ~]# umount /house/ [root@rhel6 ~]# mount -a -> SUCCESSFUL AGAIN [root@rhel6 ~]# ls /house/ lost+found Please let me know if I am missing anything here. Thanks in advance.

  Read the article

• Why doesn't Apache start from xampp control panel after changes to vhosts config?

  - by Grafica

  I'm running xampp on my local server, and want to host multiple sites, so I changed the httpd-vhosts.conf file. Will somebody let me know if there is something wrong with my code? Apache was running while I had only one site in the config, but after I added another site, I stopped apache, and I'm not able to restart it. # # Virtual Hosts # # If you want to maintain multiple domains/hostnames on your # machine you can setup VirtualHost containers for them. Most configurations # use only name-based virtual hosts so the server doesn't need to worry about # IP addresses. This is indicated by the asterisks in the directives below. # # Please see the documentation at # <URL:http://httpd.apache.org/docs/2.2/vhosts/> # for further details before you try to setup virtual hosts. # # You may use the command line option '-S' to verify your virtual host # configuration. # # Use name-based virtual hosting. # ##NameVirtualHost *:80 # # VirtualHost example: # Almost any Apache directive may go into a VirtualHost container. # The first VirtualHost section is used for all requests that do not # match a ServerName or ServerAlias in any <VirtualHost> block. # ##<VirtualHost *:80> ##ServerAdmin [email protected] ##DocumentRoot "C:/xampp/htdocs/dummy-host.localhost" ##ServerName dummy-host.localhost ##ServerAlias www.dummy-host.localhost ##ErrorLog "logs/dummy-host.localhost-error.log" ##CustomLog "logs/dummy-host.localhost-access.log" combined ##</VirtualHost> ##<VirtualHost *:80> ##ServerAdmin [email protected] ##DocumentRoot "C:/xampp/htdocs/dummy-host2.localhost" ##ServerName dummy-host2.localhost ##ServerAlias www.dummy-host2.localhost ##ErrorLog "logs/dummy-host2.localhost-error.log" ##CustomLog "logs/dummy-host2.localhost-access.log" combined ##</VirtualHost> NameVirtualHost * <VirtualHost *> DocumentRoot "C:\xampp\htdocs" ServerName localhost </VirtualHost> <VirtualHost *> DocumentRoot "C:\xampp\htdocs" ServerName evamagnus.com <Directory "C:\xampp\htdocs\"> Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost *> DocumentRoot "C:\xampp\htdocs2\" ServerName mygrafica.com <Directory "C:\xampp\htdocs2\"> Order allow,deny Allow from all </Directory> </VirtualHost> Here is what it says in the control panel: 2:17:37 PM [apache] Starting apache service... 2:17:38 PM [apache] Status change detected: running 2:17:39 PM [apache] Status change detected: stopped Thanks in advance.

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• Change default DNS server in Arch Linux

  - by AntoineG

  I'm in Viet Nam and most social websites (Facebook, Twitter and the likes - even reddit) are blocked by the ISP DNS server. I tried to change the DNS server of my Arch box using the resolv.conf file, but it failed miserably since dhcpd generates this file automatically everytime I connect to the LAN. I've been looking around to try and find out how to fix this, without success. Either I s*ck at Googling, either it is non-trivial to do so. EDIT 1: Meh, apparently posting it here made me feel guilty and I had to push my search a bit more. I found the same article than Ankur post below. This is what I made, if anybody ever faces the same problem: $ sudo gvim /etc/dhcpcd.conf Add "nohook resolv.conf" at the tail of the file. $ sudo gvim /etc/resolv.conf Add to the file (OpenDNS servers): nameserver 208.67.222.222 nameserver 208.67.220.220 Or (Google DNS): nameserver 8.8.8.8 nameserver 8.8.4.4 Then, verify it worked (need package dnsutils): $ dig www.facebook.com ; <<>> DiG 9.9.1-P1 <<>> www.facebook.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 16994 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 1 ;; OPT PSEUDOSECTION: ; EDNS: version: 0, flags:; udp: 4096 ;; QUESTION SECTION: ;www.facebook.com. IN A ;; ANSWER SECTION: www.facebook.com. 89 IN A 69.171.224.53 ;; Query time: 87 msec ;; SERVER: 208.67.222.222#53(208.67.222.222) ;; WHEN: Thu Jun 28 00:43:23 2012 ;; MSG SIZE rcvd: 61 See ;; SERVER: 208.67.222.222#53(208.67.222.222), it worked.

  Read the article

• Vagrant - Failed login, ssh not set up

  - by motleydev

  This question is two fold because somewhere in my attempts to solve the problem, I created a new one. First: I was trying to vagrant up using a Vagranfile based on the standard hashicorp/precise32 box. Everything worked up until default: SSH auth method: private key where it would eventually time out. Enabling gui in the Vagrantfile showed that the machine never actually logs in. I can use the standard user/pass and log in from that point but the vagrant up process still remains at that prior status. Here's where my understanding might be a little dim. I've tried setting auth method from the insecure_pass_key to my root ~/.ssh/id_rsa or whichever one I wanted to use. I'm not entirely sure where to put a copy of the public key or my authorized keys file. I've got a .vagrant.d folder in my user dir (I'm on OSX) which seems to contain the box images. I've got a .vagrant folder in my directory with the Vagrantfile which seems to contain the specific machine I am building off of. I've tried pouring over the docs and forums but I seem to be missing a key concept here. And Now: After a host of tips/tricks such as rolling back by VirtualBox install, uninstalling/reinstalling Vagrant and VritualBox several times, when I try to run vagrant ssh-config with a Vagrantfile based on the same hashicorp/precise32 it says that the box is not enabled for SSH. Specifically, this error: The provider for this Vagrant-managed machine is reporting that it is not yet ready for SSH. Depending on your provider this can carry different meanings. Make sure your machine is created and running and try again. Additionally, check the output of `vagrant status` to verify that the machine is in the state that you expect. If you continue to get this error message, please view the documentation for the provider you're using. So now I am slightly up a creek. Any help would be appreciated if not just clarifying a concept. Some pertinent info: I'm on OSX Maverics Due to the fact I'm running a dual HD system with system files on one HD and user files on another, my permissions are a little wonky and VBoxManage will only let me run commands via Sudo - not sure if it's pertinent - but maybe. I have no idea what I'm doing. That part is perhaps more important.

  Read the article

• Using curl -s in *nix command line not working for some reason

  - by JM4

  I am trying to install composer (though to be honest I really have no idea how it fully works and documentation seems to be quite poor) on my MediaTemple DV machine. I am using their [instructions][1] Trying to install globally using: $ curl -s https://getcomposer.org/installer | php My command line (again using putty and logged into my server as root) thinks for a second, then sets up for next prompt. I run a simple ls -l to check for the file it should have downloaded with no luck. Any idea what could be causing the issue? I have tested and do in fact have curl installed. UPDATE 1 Based on the first answer, the verbose response is: > $ curl -vs https://getcomposer.org/installer | php > * About to connect() to getcomposer.org port 443 > * Trying 37.59.4.156... connected > * Connected to getcomposer.org (37.59.4.156) port 443 > * successfully set certificate verify locations: > * CAfile: /etc/pki/tls/certs/ca-bundle.crt CApath: none > * SSLv2, Client hello (1): SSLv3, TLS handshake, Server hello (2): SSLv3, TLS handshake, CERT (11): SSLv3, TLS handshake, Server key > exchange (12): SSLv3, TLS handshake, Server finished (14): SSLv3, TLS > handshake, Client key exchange (16): SSLv3, TLS change cipher, Client > hello (1): SSLv3, TLS handshake, Finished (20): SSLv3, TLS change > cipher, Client hello (1): SSLv3, TLS handshake, Finished (20): SSL > connection using DHE-RSA-AES256-SHA > * Server certificate: > * subject: /C=CH/CN=dl.packagist.org/[email protected] > * start date: 2012-07-07 23:25:35 GMT > * expire date: 2013-07-10 02:55:12 GMT > * SSL: certificate subject name 'dl.packagist.org' does not match target host name 'getcomposer.org' > * Closing connection #0 > * SSLv3, TLS alert, Client hello (1): > > > [1]: http://getcomposer.org/doc/00-intro.md

  Read the article

• SQL 2008 R2 Named Instance Client Connectivity Issues?

  - by Jerry Dodge

  We're upgrading our software from using SQL 2000 to 2008 R2. Our customers will be installing an update which uninstalls 2000 and installs 2008 R2 under the same instance. So if no instance existed, then no instance name will be set (default). However, the problem starts with the customers which have a named SQL instance. Starting in 2008 R2 (not sure of ones before), for some reason, a client connecting to the server by its instance name is unsuccessful. I'm testing from the Management Studio - if I can't connect this, then nothing can connect. I browse network servers, and find the specific server\instance in the list. But, upon trying to connect to an instance name like MyServer\INST, I get: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) I do in fact have TCP/IP and Named Pipes protocols enabled, this is the first thing I did. When I connect to the server using a comma (,) and port number like MyServer, 49195, it works just fine. So it appears that client computers are just unable to identify the instance names. This has happened on all our installations of SQL 2008 R2 and from all client computers, including Win 7, XP, Vista, Server 2008, and Server 2003. We never experienced such issues on earlier versions of SQL. The problem even persists if the firewalls and antiviruses are all disabled. Now, this is a large update which we will be distributing soon to all our customers, and we want to minimize the interaction they need with us to get this installed. We absolutely hate the idea of using a port number, because it will always be different, and we would have to modify each client to point to this server/port. Some of our customers may have hundreds of client computers. How do I make client connections to a named SQL instance work again? After all, this is the whole purpose of named instances, and if a client can't connect to this instance by its name, then what is it even named for? EDIT It was mentioned to make sure SQL Browser is running, so I checked, and it is running. The server is also able to connect to its self (locally) - just external connections are refused. UPDATE After more careful checking, I learned the firewall wasn't completely disabled when testing, and upon disabling it completely, this works. So it appears that SQL Browser is being blocked by the firewall from external clients from accessing.

  Read the article

• Wake On Lan only works on first boot, not sequent ones

  - by sp3ctum

  I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

  Read the article

• Windows 8 with LiveID login authenticates as Guest to remote SQl Server

  - by Tim Long

  I have a network where several users are using Office Accounting 2009 in multi-user client/server mode. OA is built on SQL Server. One PC acts as the 'server' and has the SQl Server instance, the others have only the application installed and no SQL instance, all of the apps connect remotely to the SQL instance on the 'server'. I'm using the term 'server' loosely here, it is just a normal workstation that happens to be designated as the server and runs the SQL instance. There is no NT domain, all user accounts are local accounts. The way that OA works in multi-user mode is that each user is required to have a local account with the same username and password on both the client and 'server' PCs. This has been working well, no along comes Windows 8. I use my 'Microsoft Account' aka LiveID to log into Windows 8. Office Accounting runs fine and attempts to connect to the database, but fails, 'you do not have permission to perform this operation'. In the SQL logs, I get this error: 2012-10-28 17:54:01.32 Logon Error: 18456, Severity: 14, State: 11. 2012-10-28 17:54:01.32 Logon Login failed for user 'SERVER\Guest'. Reason: Token-based server access validation failed with an infrastructure SERVER is the hostname of the server. So it seems to be authenticating as 'Guest'?? To verify this, I enabled the Guest account on the 'server' PC and then added Guest as an allowed user within Office Accounting (this simply creates the user in SQL and gives it an appropriate database role). Sure enough, My Windows 8 PC was then able to connect to the database when using Office Accounting. Clearly, having users authenticate as 'Guest' stinks from a security and auditing standpoint. So what I need are some ideas for how to work around this. I've tried switching the Windows 8 PC to a 'local account' and that works too, but requires giving up significant functionality on the Windows 8 PC. What I really need is a way to force the Windows 8 PC to use a specific set of credentials when connecting to the remote SQL instance. Office Accounting takes the logged in username, which is my LiveID and doesn't correspond to any Windows user name. Anyone solved this issue?

  Read the article

• Our VPS is being used as a Warez mule

  - by Mikuso

  The company I work for runs a series of ecommerce stores on a VPS. It's a WAMP stack, 50gb storage. We use an archaic piece of ecommerce software which operates almost entirely client-side. When an order is taken, it writes it to disk and then we schedule a task to download the orders once every 10 minutes. A few days ago, we ran out of disk space, which caused orders to fail to be written. I quickly hopped on to delete some old logs from the mailserver and freed up a couple of GB pretty quickly, but I wondered how we could fill up 50gb will nothing much more than logs. Turns out, we didn't. Hidden deep within the c:\System Volume Information directory, we have a stack of pirated videos, which seem to have appeared (looking at the timestamps) over the past three weeks. Porn, American Sports, Australian cooking shows. A very odd collection. Doesn't look like an individual's personal tastes - more like the VPS is being used as a mule. We have a 5-attempts and you're blocked policy on our FTP server (plus, there is no FTP account with access to that directory), and the windows user account has had it's password changed recently. The main avenues are sealed - and logs can verify that. I thought I'd watch and see if it happened again, and yes, another cooking show has appeared this morning. I am the only one to know of this problem at my company, and only one of two with access to the VPS (the other being my boss, but no - it's not him). So how is this happening? Is there a vulnerability in some of the software on the VPS? Are the VPS owners peddling warez across our rented space? (can they do this?) I don't want to delete the warez in case it is seen as a hostile action against this outside force, and they choose to retaliate. What should I do? How do I troubleshoot this? Has this happened to anyone else before?

  Read the article

• Powershell: Cannot connect via SSL

  - by JSWork

  Am following "secrets to powershell remoting" to setup an SLL account and seem to be missing a step. I ran Winrm create winrm/config/Listener?Address=*+Transport=HTTPS @{Hostname="redacted";CertificateThumbprint="redacted"} and got PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_1184937132 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_1184937132 Name Value Type ---- ----- ---- Address * System.String Transport HTTP System.String Port 5985 System.String Hostname System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_1187163138 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_1187163138 Name Value Type ---- ----- ---- Address * System.String Transport HTTP System.String Port 80 System.String Hostname System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String PS WSMan:\localhost&gt; dir wsman:\localhost\listener\Listener_220862350 WSManConfig: Microsoft.WSMan.Management\WSMan::localhost\Listener\Listener_220862350 Name Value Type ---- ----- ---- Address * System.String Transport HTTPS System.String Port 5986 System.String Hostname redacted System.String Enabled true System.String URLPrefix wsman System.String CertificateThumbprint redacted System.String ListeningOn_756355952 10.0.0.54 System.String ListeningOn_1201550598 127.0.0.1 System.String Trouble is when i do this PS C:\Users\redacted> enter-pssession -Computername redacted -Credential redacted\redacted -UseSSL I get this Enter-PSSession : Connecting to remote server failed with the following error message : The client cannot connect to th e destination specified in the request. Verify that the service on the destination is running and is accepting requests . Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or Win RM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". For more information, see the about_Remote_Troubleshooting Help topic. At line:1 char:16 + enter-pssession <<<< -Computername redacted -Credential redacted\redacted -UseSSL + CategoryInfo : InvalidArgument: (redacted:String) [Enter-PSSession], PSRemotingTransportException + FullyQualifiedErrorId : CreateRemoteRunspaceFailed This happens even when the firewall is off completely and when the machine tires to connect to itself locally. On top of that, despite the listners eing lsited on wsman, when I run PS WSMan:\localhost&gt; Get-PSSessionConfiguration I get Name PSVersion StartupScript Permission ---- --------- ------------- ---------- Microsoft.PowerShell 2.0 PS WSMan:\localhost&gt; Any ideas what I'm missing/doing wrong? edit: Windows 2003. Powershell v2.0

  Read the article

• WinPE, Startnet.CMD and passing variables to second batch file not working

  - by user140892

  I don't know scripting or PowerShell (yes I need to learn something). I'm not an expert batch file maker either. I have a WinPE flash drive which I used to deploy OS images. I have the WIM, drivers and anything needed else outside the WinPE environment to ensure that Updates, changes are easier for me to make. I use the "STARTNET.CMD" batch file which is part of the WinPE. The reason to go through the letter drives is that the WinPE always gets the X letter drive assigned. The flash drive itself can receive a random letter which always changes. My deployment menu is located on the flash drive it self and not inside the WinPE. This is so that if I need to make a change I don't have to re-do the WinPE. I am able to locate the "menu.bat" batch file and launch it. I use a variable to capture the letter drive. I call the second batch file named "menu.bat" and pass the variable to it. When the second batch file loads, I believe that I am calling the variable correctly. If I break out of the batch file I can echo the variable and see the expected reply. The issue is that I can't use the variable to work with anything on the second batch file. In my test, I can get this to work over and over. When it runs from the real USB flash drive it does not work. I removed comments from the second batch file to make it smaller. My issue is that files below all get a message stating that the system cannot find the path specified. Diskpart Imagex.exe bcdboot.exe Why can't I get the varible to properly function when I try to using example "ImageX.exe"? Contents of the Startnet.cmd @echo off for %%p in (a b c d e f g h i j k l m n o p q r s t u v w x y z) do if exist %%p:\Tools\ set w=%%p Set execpatch=%w%\Tools\ call %w%:\Menu.bat \Tools\ Contents of the Menu.BAT @echo off set SecondPath=%1 cls :Start cls Echo. Echo.============================================================== Echo. Windows 7 64 Bit Ent Basic Desktops Echo.============================================================== Echo. Echo A. 790 Windows 7 - Basic Echo. Echo. Echo I. Exit Echo. Echo. set /p choice=Choose your option = if not '%choice%'=='' set choice=%choice:~0,1% if '%choice%'=='a' goto 790_Windows_7_Basic echo "%choice%" is not a valid (answer/command) echo. goto start :790_Windows_7_Basic REM DISKPART /s %SecondPath%BatchFiles\Make-Partition.txt %SecondPath%imagex.exe /apply %SecondPath%Images\Win7-64b-Ent-Basic-SysPreped.wim 1 o:\ /verify %SecondPath%bcdboot.exe o:\Windows /s S: Copy %SecondPath%Unattended\unattend.XML o:\Windows\System32\sysprep\unattend.XML /y xcopy %SecondPath%Drivers\790\*.* o:\Windows\INF\790\ /E /Q /Y MD o:\Windows\Setup\Scripts\ Copy %SecondPath%BatchFiles\SetupComplete.cmd o:\Windows\Setup\Scripts\ /y Goto Done :Done Exit

  Read the article

• IIS6 Virtual Directory 500 Error on Remote Share

  - by David Boike

  We have our servers at the server farm in a domain. Let's call it LIVE. Our developer computers live in a completely separate corporate domain, miles and miles away. Let's call it CORP. We have a large central storage unit (unix) that houses images and other media needed by many webservers in the server farm. The IIS application pools run as (let's say) LIVE\MediaUser and use those credentials to connect to a central storage share as a virtual directory, retrieve the images, and serve them as if they were local on each server. The problem is in development. On my development machine. I log in as CORP\MyName. My IIS 6 application pool runs as Network Service. I can't run it as a user from the LIVE domain because my machine isn't (and can not be) joined to that domain. I try to create a virtual directory, point it to the same network directory, click Connect As, uncheck the "Always use the authenticated user's credentials when validating access to the network directory" checkbox so that I can enter the login info, enter the credentails for LIVE\MediaUser, click OK, verify the password, etc. This doesn't work. I get "HTTP Error 500 - Internal server error" from IIS. The IIS log file reports sc-status = 500, sc-substatus = 16, and sc-win32-status = 1326. The documentation says this means "UNC authorization credentials are incorrect" and the Win32 status means "Logon failure: unknown user name or bad password." This would be all and good if it were anywhere close to accurate. I double- and trouble-checked it. Tried multiple known good logins. The IIS manager allows me to view the file tree in its window, it's only the browser that kicks me out. I even tried going to the virtual directory's Directory Security tab, and under Authentication and Access Control, I tried using the same LIVE domain username for the anonymous access credential. No luck. I'm not trying to run any ASP, ASP.NET, or other dynamic anything out of the virtual directory. I just want IIS to be able to load static images, css, and js files. If anyone has some bright ideas I would be most appreciative!

  Read the article

• SMB returns the entire file instead of header info

  - by billdlawson

  Starting a section of code checks for access to many data files (flat files so each table is a file) and when I do a packet capture, in our capture only the header info is sent by the server to the client. However I have one Customer who is using a SAN that gets the whole file instead of just the header info,and besides just being slower, this is causing file access issues. They have already turned off OPLOCKS at the server and at the workstations. This is not client server. The data files and the application reside on the server but the users run the application locally via a shortcut with a mapped drive or UNC. So when I simply select an option that prompts for a vehicle number, not tryng to select a record but rather simply verify the datafiles are accessible, that window opens in 1-2 seconds for me. When they do the same thing it takes 6-15 seconds after there several users are running the program. Maximum number of users is 15. The program has a lot of small modules, 800 .cob modules. So it is very chatty but these are datafiles. We have Wireshark captures that show he's pulling the whole file and we're just getting the header. Thier capture vs ours. We suspect the SAN. Has anyone ever heard of a SAN improperly interpreting runtime requests? So an SMB request. This is Acucobol-GT (now Microfocus). The application is written in COBOL. This is not a new program just a new problem. This is one customer of over a thousand who are otherwise running smoothly and we are totally stumped. All XP users, the server is Windows 2003 (with Virtual server) and I don't yet know the SAN info. Also we have many installations running virtual servers but only few on SANs or we just don't know it. This is not a network throught put issue, the load is less than 5% on the server and theer are no timeout or retransmits. PS If it wasn't for Wireshark I'd still be chasing my tail. An application trace file on thier installation just looks like they run slower. If you want the Wireshark trace file I can make it available. Thanks in advance - Please excuse my verbosity (word?) but I'm not sure what's relavent.

  Read the article

• How to get physical partition name from iSCSI details on Windows?

  - by Barry Kelly

  I've got a piece of software that needs the name of a partition in \Device\Harddisk2\Partition1 style, as shown e.g. in WinObj. I want to get this partition name from details of the iSCSI connection that underlies the partition. The trouble is that disk order is not fixed - depending on what devices are connected and initialized in what order, it can move around. So suppose I have the portal name (DNS of the iSCSI target), target IQN, etc. I'd like to somehow discover which volumes in the system relate to it, in an automated fashion. I can write some PowerShell WMI queries that get somewhat close to the desired info: PS> get-wmiobject -class Win32_DiskPartition NumberOfBlocks : 204800 BootPartition : True Name : Disk #0, Partition #0 PrimaryPartition : True Size : 104857600 Index : 0 ... From the Name here, I think I can fabricate the corresponding name by adding 1 to the partition number: \Device\Harddisk0\Partition1 - Partition0 appears to be a fake partition mapping to the whole disk. But the above doesn't have enough information to map to the underlying physical device, unless I take a guess based on exact size matching. I can get some info on SCSI devices, but it's not helpful in joining things up (iSCSI target is Nexenta/Solaris COMSTAR): PS> get-wmiobject -class Win32_SCSIControllerDevice __GENUS : 2 __CLASS : Win32_SCSIControllerDevice ... Antecedent : \\COBRA\root\cimv2:Win32_SCSIController.DeviceID="ROOT\\ISCSIPRT\\0000" Dependent : \\COBRA\root\cimv2:Win32_PnPEntity.DeviceID="SCSI\\DISK&VEN_NEXENTA&PROD_COMSTAR... Similarly, I can run queries like these: PS> get-wmiobject -namespace ROOT\WMI -class MSiSCSIInitiator_TargetClass PS> get-wmiobject -namespace ROOT\WMI -class MSiSCSIInitiator_PersistentDevices These guys return information relating to my iSCSI target name and the GUID volume name respectively (a volume name like \\?\Volume{guid-goes-here}), but the GUID volume name is no good to me, and there doesn't appear to be a reliable correspondence between the target name and the volume that I can join on. I simply can't find an easy way of getting from an IQN (e.g. iqn.1992-01.com.example:storage:diskarrays-sn-a8675309) to physical partitions mapped from that target. The way I do it by hand? I start Disk Management, and look for a partition of the correct size, verify that its driver says NEXENTA COMSTAR, and look at the disk number. But even this is unreliable if I have multiple iSCSI volumes of the exact same size. Any suggestions?

  Read the article

• How to specify this 'symbolic link' for the Jungo WinDriver?

  - by user252098

  Just now , I try to install the Jungo WinDriver in the Ubuntu 13.10 . But I am puzzled by the its manual : 4.2.3. Linux WinDriver Installation Instructions 4.2.3.1. Preparing the System for Installation In Linux, kernel modules must be compiled with the same header files that the kernel itself was compiled with. Since WinDriver installs kernel modules, it must compile with the header files of the Linux kernel during the installation process. Therefore, before you install WinDriver for Linux, verify that the Linux source code and the file version.h are installed on your machine: Install the Linux kernel source code: If you have yet to install Linux, install it, including the kernel source code, by following the instructions for your Linux distribution. If Linux is already installed on your machine, check whether the Linux source code was installed. You can do this by looking for 'linux' in the /usr/src directory. If the source code is not installed, either install it, or reinstall Linux with the source code, by following the instructions for your Linux distribution. Install version.h: The file version.h is created when you first compile the Linux kernel source code. Some distributions provide a compiled kernel without the file version.h. Look under /usr/src/linux/include/linux to see whether you have this file. If you do not, follow these steps: Become super user: $ su Change directory to the Linux source directory: cd /usr/src/linux Type: make xconfig Save the configuration by choosing Save and Exit. Type: make dep Exit super user mode: exit To run GUI WinDriver applications (e.g., DriverWizard [5]; Debug Monitor [7.2]) you must also have version 5.0 of the libstdc++ library — libstdc++.so.5. If you do not have this file, install it from the relevant RPM in your Linux distribution (e.g., compat-libstdc++). Before proceeding with the installation, you must also make sure that you have a linux symbolic link. If you do not, create one by typing /usr/src$ ln -s 'target kernel'/linux For example, for the Linux 2.4 kernel type /usr/src$ ln -s linux-2.4/ linux ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ I can't understand how to specify these two parameters in my Ubuntu .

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• How to keep group-writeable shares on Samba with OSX clients?

  - by Oliver Salzburg

  I have a FreeNAS server on a network with OSX and Windows clients. When the OSX clients interact with SMB/CIFS shares on the server, they are causing permission problems for all other clients. Update: I can no longer verify any answers because we abandoned the project, but feel free to post any help for future visitors. The details of this behavior seem to also be dependent on the version of OSX the client is running. For this question, let's assume a client running 10.8.2. When I mount the CIFS share on an OSX client and create a new directory on it, the directory will be created with drwxr-x-rx permissions. This is undesirable because it will not allow anyone but me to write to the directory. There are other users in my group which should have write permissions as well. This behavior happens even though the following settings are present in smb.conf on the server: [global] create mask= 0666 directory mask= 0777 [share] force directory mode= 0775 force create mode= 0660 I was under the impression that these settings should make sure that directories are at least created with rwxrwxr-x permissions. But, I guess, that doesn't stop the client from changing the permissions after creating the directory. When I create a folder on the same share from a Windows client, the new folder will have the desired access permissions (rwxrwxrwx), so I'm currently assuming that the problem lies with the OSX client. I guess this wouldn't be such an issue if you could easily change the permissions of the directories you've created, but you can't. When opening the directory info in Finder, I get the old "You have custom access" notice with no ability to make any changes. I'm assuming that this is caused because we're using Windows ACLs on the share, but that's just a wild guess. Changing the write permissions for the group through the terminal works fine, but this is unpractical for the deployment and unreasonable to expect from anyone to do. This is the complete smb.conf: [global] encrypt passwords = yes dns proxy = no strict locking = no read raw = yes write raw = yes oplocks = yes max xmit = 65535 deadtime = 15 display charset = LOCALE max log size = 10 syslog only = yes syslog = 1 load printers = no printing = bsd printcap name = /dev/null disable spoolss = yes smb passwd file = /var/etc/private/smbpasswd private dir = /var/etc/private getwd cache = yes guest account = nobody map to guest = Bad Password obey pam restrictions = Yes # NOTE: read smb.conf. directory name cache size = 0 max protocol = SMB2 netbios name = freenas workgroup = COMPANY server string = FreeNAS Server store dos attributes = yes hostname lookups = yes security = user passdb backend = ldapsam:ldap://ldap.company.local ldap admin dn = cn=admin,dc=company,dc=local ldap suffix = dc=company,dc=local ldap user suffix = ou=Users ldap group suffix = ou=Groups ldap machine suffix = ou=Computers ldap ssl = off ldap replication sleep = 1000 ldap passwd sync = yes #ldap debug level = 1 #ldap debug threshold = 1 ldapsam:trusted = yes idmap uid = 10000-39999 idmap gid = 10000-39999 create mask = 0666 directory mask = 0777 client ntlmv2 auth = yes dos charset = CP437 unix charset = UTF-8 log level = 1 [share] path = /mnt/zfs0 printable = no veto files = /.snap/.windows/.zfs/ writeable = yes browseable = yes inherit owner = no inherit permissions = no vfs objects = zfsacl guest ok = no inherit acls = Yes map archive = No map readonly = no nfs4:mode = special nfs4:acedup = merge nfs4:chown = yes hide dot files force directory mode = 0775 force create mode = 0660

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Exchange 2010 Internal Auto Discover Migrate away from current .local DNS name

  - by Bryan

  We have an Exchange 2010 Server, running within our Active Directory domain, with an internal hostname of server.example.local. The server is configured for Exchange anywhere, but currently has a self signed certificate with a name of server.example.local installed. Internally, clients connect and work fine, but externally, we are having certificate errors as you would expect. I'm about to purchase a UCC SSL Certificate to install on the server with all the relevant SANs on the certificate to correct this, but due to obvious problem obtaining a trusted cert with .local as a subject alternative name, I'm looking to configure clients on the internal network so that they don't use any reference to the .local hostname. I've configured our external DNS name for the server as exchange.example.com, and have created an CNAME for autodiscover.example.com which also (correctly) points to exchange.example.com. I've also configured internal DNS records for these two hostnames which point to the internal interface of the same server. I don't anticipate any problems here. I'm now trying to reconfigure Auto Discover internally, so that Outlook attempts to connect to exchange.example.com. I've followed the steps in KB940726 to prepare for this, and this appeared to work fine. No errors were generated and I was able to verify the CAS name in AD using ADSI edit. I've just tried testing this with a newly created test user account complete with a new Exchange mailbox, and Outlook 2007 connects fine on the internal network, but looking deeper in the Exchange profile, Outlook is still resolving the server name as server.example.local. Could it be the self signed cert, that is causing Outlook to display the server name as server.example.local, or is there still something wrong with my internal autodiscover configuration? Edit I've proven it isn't the certificate that is responsible for outlook returning server.example.local, by installing another self certified certificate with a name of test.example.com. When creating a new outlook profile, I get the mismatch error I'm expceting, but after accepting the cert, and finishing the config of the Outlook profile, again it still shows server.example.local as the server name. This means that if I were to purchase the UCC cert now, that external client would work fine, but internal clients would show a certificate name mismatch. Any ideas where to start diagnosing this?

  Read the article

• Emails not being delivered

  - by Tomtiger11

  Comment pointed out that this may fix my problem, and it did: Why don't mails show up in the recipient's mailspool? I use Postfix with Dovecot, and when I send an email from my gmail to my server, it is received at the server, but not at my email client using POP3. I can verify it being received at the server using the mail command. This is my main.cf: queue_directory = /var/spool/postfix command_directory = /usr/sbin daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix mail_owner = postfix myhostname = tom4u.eu myorigin = $myhostname inet_interfaces = all inet_protocols = all unknown_local_recipient_reject_code = 550 relay_domains = $mydomain alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin ddd $daemon_directory/$process_name $process_id & sleep 5 sendmail_path = /usr/sbin/sendmail.postfix newaliases_path = /usr/bin/newaliases.postfix mailq_path = /usr/bin/mailq.postfix setgid_group = postdrop html_directory = no manpage_directory = /usr/share/man sample_directory = /usr/share/doc/postfix-2.6.6/samples readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES smtpd_tls_cert_file = /etc/postfix/certs/cert.pem milter_protocol = 2 milter_default_action = accept smtpd_milters = inet:localhost:8891 non_smtpd_milters = inet:localhost:8891 smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_local_domain = $myhostname smtpd_recipient_restrictions = reject_non_fqdn_recipient,permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination,permit broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth If you could help me with this, I'd be most grateful, if you need any more information, please ask. var/log/maillog: May 30 22:44:25 tom4u postfix/smtpd[18626]: connect from mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/smtpd[18626]: 318F679B7F: client=mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/cleanup[18631]: 318F679B7F: message-id=<CAA_0zdxY-WUFGOC57K_yVn0G+5hN=8KSXuohJqMDB5Rm7bqu8w@mail.gmail.com> May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: mail-we0-f181.google.com [74.125.82.181] not internal May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: not authenticated May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: DKIM verification successful May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: s=20120113 d=gmail.com SSL May 30 22:44:25 tom4u postfix/qmgr[16282]: 318F679B7F: from=<[email protected]>, size=1720, nrcpt=1 (queue active) May 30 22:44:25 tom4u postfix/smtpd[18626]: disconnect from mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/local[18632]: 318F679B7F: to=<[email protected]>, relay=local, delay=0.17, delays=0.12/0.01/0/0.03, dsn=2.0.0, status=sent (delivered to mailbox) May 30 22:44:25 tom4u postfix/qmgr[16282]: 318F679B7F: removed May 30 22:45:32 tom4u dovecot: pop3-login: Login: user=<tom>, method=PLAIN, rip=SNIP, lip=176.31.127.165, mpid=18679 May 30 22:45:32 tom4u dovecot: pop3(tom): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0 May 30 22:46:32 tom4u dovecot: pop3-login: Login: user=<tom>, method=PLAIN, rip=SNIP, lip=176.31.127.165, mpid=18725 May 30 22:46:32 tom4u dovecot: pop3(tom): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0

  Read the article

• Gigabyte GA-Z77X-D3H MB problems

  - by Hans

  I installed a new system last week. I've some issues with it. The system consists of a: Gigabyte GA-Z77X-D3H with F9 BIOS (latest) Intel Core i5 3570K proccesor Sapphire Radeon HD7850 2x 8GB Corsair 1600MHz memory OCZ Vertex 2 120G SSD Connected peripherals : 2 Samsung 940BF (1 via DVI on GFX card, 1 via an Displayport to DVI adapter) 1 Dell U2312HM monitor (displayport) Dell USB Hub (monitor) Wired mouse, wireless keyboard (logitech) Logitch G25 wheel Canon MP800 printer Okay, my issues are the following: if I plug in 1 or more monitor at DisplayPort during boot, most of the time it won't boot properly. I get an empty message screen of UEFI: only the header GIGABYTE DUEL BIOS appears. The system reboots itself, turns on for a few seconds (no video) and then reboots again. Now it starts all over again. This repeats until I remove all displayport monitors. Windows boots, and I can use them when I replug them. The graphics card has been running fine for a few weeks on an older system (intel Q6600). Another issue is; if I plug in my G25 steering wheel, the UEFI BIOS is inaccessible. It either gives the same empty UEFI screen, or the BIOS screen is rendering but crashes half way (so pieces of text and graphics are missing, and it has crashed). If I remove the G25, all is fine. To verify the graphics card is OK and the motherboard is causing these issues, I tried an NVIDIA 8800GT graphics card. This hasn't got Displayport, but it also cannot boot the BIOS with the G25 wheel plugged in. The PC also refuses to go into or out of standby. It just hangs when going into standby, and in other occasions (when it does succesfully do so) get out of standby. Power supply is OCZ StealthXStream 600W. Proccesor is 25 - 30C idle, ~55C stressed (Scythe Mugen 2). I am really puzzled what can be done to resolve this. I am not really waiting for an RMA request (otherwise I will return the MB for another type), because it will likely mean I have to wait very long before I get a replacement. Anyone else with a similar experience on this board/chipset or can help me troubleshoot this?

  Read the article

• What the best way to recover from when your RAID H/W incorrectly thinks a disk is missing

  - by Software Monkey

  I have a Windows 7 system with an MSI motherboard (running the latest AMD BIOS) and two of my four disks (not the system boot disk) configured via the Mobo as RAID-1. After a normal system restart today, the RAID BIOS reports that one of the two drives has been disconnected or has failed. It's not really failed; via recovery tools I can verify that if I take the BIOS out of RAID mode. But I can find no way to re-add the second hard disk to the array and rebuild via the BIOS - the only option seems be to delete the array and recreate it, but I've done that once before and it blows away the disk. It's done this once before, however on a subsequent reboot after double-checking the drive cabling (but not changing anything) and it boot up fine. So I think the mobo RAID is a little bit flaky. At this point I would like to remove the RAID drivers, change to AHCI mode and switch over to using a Windows 7 dynamic mirror disk. But the RAID drivers seem somehow deeply bound into the Windows startup - I can't find anything like the good ol' safe-mode in Windows 7. If I boot from the Win 7 install disk in ACHI mode I can use recovery tools to log in to the Windows 7 installation, so the boot drive it seems fine with ACHI mode. Additionally, I can see all my other disks, run chkdsk on them and they seem to be fine. If I try to boot from the HDD in AHCI mode, it just reboots part way through, presumably because the RAID drivers load and conflict with the BIOS being set to AHCI. So: How do I strip the RAID drivers from my Win 7 installation? If I delete the RAID logical disk, will it really delete partitioning information, or is that just a poorly worded message when it says the data on the disk will be deleted? If I disconnect the 2 disks in a RAID array, then delete the logical disk array, and then reconnect and reboot still in RAID mode, will the disks simply revert to RAID single-disks like my other 2 and then maybe I can leave windows with RAID drivers by operate the disks as singles with 2 of them in a Windows dynamic disk mirrored setup? Does Windows 7 have anything like the Windows XP Repair Install, where it will reinstall the O/S binaries from CD, but leave apps and setup alone. I am really hoping I don't have to do a complete reinstall of Windows 7 - the last one, when I upgraded from XP, took me two days to get everything set up and installed.

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >