Search Results

Search found 4153 results on 167 pages for 'rave reports'.

Page 83/167 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

• Reconfigure RAID on Dell PowerEdge T710

  - by Stefano Borini

  I have a Dell PowerEdge T710 under my feet at this very moment, with RedHat Enterprise Server 5.3. I have 6 1TB disks and two 500GB. parted reports two devices, one 500 GB and the other 4 TB. So I assume the RAID has been setup as mirror for two disks, and I assume as RAID 5 the remaining ones. I say "I assume" because it does not make sense. Having 6 disks in RAID 5, I should obtain a total space of 5 TB, not 4TB. It's not even RAID 10: I would end up with a 3 TB unit. How can I check and eventually modify the RAID array definition? In the Fujitsu Siemens I played with some time ago, at boot I had the chance to enter the controller BIOS, but here I don't see a clear way to perform this operation.

  Read the article

• Windows 7 KSOD On Login

  - by Brandon Bertelsen

  For those that are unaware, KSOD means blacK Screen of Death. Essentially, when windows starts my computer shows only the cursor and a black screen. It seems like any and all shell elements are disabled (or perhaps not started). I have seen a number of these questions asked, none of which have matched my situation. CTRL + ALT + ... does not respond Restarting in safe mode, results in the same KSOD sfc /scannow seems to have no effect when typed at the command prompt that is accessed using the recovery tools via the install disk Update to item 3: sfc /scannow reports: There is a system repair pending which requires reboot to complete. Restart Windows and run sfc again. However, Windows does not restart past KSOD. Update to item 3 as per Soandos comment re: /offbootdir sfc /scannow /offbotdir=e:\ /windir=e:\windows "Windows resource protection found corrupt files but was unable to fix some of them. Details are included in the CBS.log..."

  Read the article

• Rewriting from headers in Postfix

  - by inxilpro

  I want to configure Postfix to replace the 'From' header in all forwarded/aliased messages with a custom email address, and the 'Reply-To' header with the original sender's address. Is that something that can be done with a simple configuration change, or am I looking at a more complex problem? For example: Original Message: From: "John Smith" <[email protected]> To: "Jane Rice" <[email protected]> Would get translated to: From: "My Email Forwarding Service" <[email protected]> Reply-To: "John Smith" <[email protected]> To: "Jane Rice" <[email protected]> Ideally, I would also have it rewrite the message body (adding something about how the message was forwarded for them), but I know that's much more difficult. We have a number of email aliases, and everytime someone reports spam they received through their alias, our server gets flagged. I'm trying to minimize that damage as much as possible. Any help is greatly appreciated!

  Read the article

• growing EBS RAID volume

  - by Ryan Fernandes

  I've created a RAID0 configuration with two 1GB EBS volumes, mounted at /dev/md0 using mdadm and formatted with XFS Next, I copied some files over to fill the volume to around 30% of its capacity (of 2GB) I then created snapshots of the volumes using ec2-consistent-snapshot and created volumes of the said snapshots but specified the volume size to be 2GB (effective doubling the capacity on each disk) I then spun up a new instance, assembled the RAID0 configuration on /dev/md0 from the 2 volumes mentioned above and mount it to /vol df -hT showed /vol as 2GB (as expected) Now I ran sudo xfs_growfs -d /vol. The command completed normally but reported blocks changed from 523776 to 524160 (only!) and df -hT still showed /vol as 2GB (instead of the expected 4GB) I rebooted, remounted, reassembled the RAID but it still reports the old size. Any clue as to what went wrong?

  Read the article

• Problem with regsvr32 on Windows Server 2010

  - by Chris Anton

  Hi all! I am attempting to register a basic COM dll on a Windows Server 2008 standard box. I run regsvr32 capicom.dll and it reports DllRegisterServer in capicom.dll succeeded. This is the same process we've used for years on Windows Server 2003. Sadly, when I attempt to create the object via a very very basic Microsoft vbscript example Set oStore = CreateObject("CAPICOM.Store") it throws a "ActiveX component can't create object" error. Thinking maybe it was a problem with this dll, I tried a few other DLLs we use with the same result. I tried using the regsvr32 in system, system32, and syswow64 all with the same result. I don't know too much about the differences between each of those, but figured it was worth a shot. The dll is being stored on the d:\ and seems to have correct permissions (though that'd be a different error altogether). Thanks to any help or thoughts you might have!

  Read the article

• Resetting "HDD Warning???" with Zalman ZM-VE400 external case

  - by 0xC0000022L

  Whenever I turn on (or plug in) the Zalman ZM-VE400 I have, it shows HDD Warning???. Sometimes briefly, sometimes until the Menu button is pressed. The case contains a SSD drive and as far as I understand the warning relates to the S.M.A.R.T. status of which this drive doesn't support all parts. How can I reset the warning so I don't receive it every time when turning on the drive? Firmware reports: V400_01_040_N Here's what I have tried so far: Unplug and plug back in Open the case and remove the SSD, then put it back in Press the button on the back side (cover removed) while plugged in Press the button on the back side (cover removed) while not plugged in USB Connect = Refresh = Enter USB Connect = Safe Removal = Enter Advanced = Umount VHDD = Enter

  Read the article

• Automated Deployment of Windows Application

  - by Phillip Roux

  Our development team are looking to automate our application deployment on to multiple servers. We need to control multiple windows servers at once (Stopping Database server & Web Server). We have a ASP.NET project, database upgrade scripts, reports and various Windows services that potentially need to be updated during deployment. Currently we use Jenkins as our CI server to run our unit tests. If something goes wrong in the deployment process, we would like the ability to roll back. What tools are recommended to automate our deployment process?

  Read the article

• why does chkdsk always report errors on a bad shutdown

  - by rep_movsd

  Once in a while, Windows XP hangs on my laptop (usually when going into standby or hibernate and occasionally on startup) and I have to forcefully poweroff. Ususally chkdsk never runs automatically (I thought it should know that the partitions have nit been unmounted and do that). I religiously run chkdsk without /F after bad shutdowns like this, and invariably it reports that the drive has unfixed errors and must be checked with /F and I do that, and more often than not, the chdsk that runs on startup does not report fixing anything. I have had times in the past (and not only just on this system) when not running chkdsk leads to some strange errors like files not opening even though they exist and inability to save certain files, so I make it a point to always chkdsk after bad shutdown. I never understood why this is : Isnt the whole point of a journalling filesystem like NTFS to avoid file system corruption and endless chkdsks? I even tried once disabling write caching to see if it made any difference, but to no avail....

  Read the article

• iPhone SDK 3.0 and symbolicatecrash not getting along?

  - by Steve

  * UPDATE * I've reinstalled with Snow Leopard, clean install. Completely wiped my existing Leopard install. Same problem persists. I've tried numbers of versions of symbolicatecrash to resolve symbols in my crash reports. From the version provided by Apple, to Alan's Quatermain's version posted on GitHub and finally from http://openradar.appspot.com/6438643. For whatever reason, the best results I can get is for symbols on my own libraries to get resolved. Normally, this is enough data to point me in the right direction -- other times it is not. With 2.x I had no problems getting the symbols for my code + Apple provided libraries from within the stack traces in each thread. Most likely an issue with my environment here, I'm not at all doubting the work that Apple or Alan have done. Yes I'm certain the dSYM I have stashed away is the same exact one that's generating the crash report. Although 'Foo' is me, and getting symbols from it is wonderful, I need to see symbols from the other functions in the stack to truly understand my reports. Note: For devices that crash running the app on iPhone OS 2.2.1, I have no problem getting all symbols. This is an iPhone OS 3.0 issue it appears. Also, while running symbolicatecrash in verbose mode here's a few of the things that struck me as wrong: - NO MATCH NOT searching in Spotlight for dsym with UUID of /System/Library/Frameworks/CoreFoundation.framework/CoreFoundation ## Warning: Can't find any unstripped binary that matches version of /System/Library/Frameworks/CoreFoundation.framework/CoreFoundation ..........fetching symbol file for libobjc.A.dylib--[undef] Searching [/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0 (5A345)/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0 (5A347)/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0.1 (5B108)/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0.2 (5C1)/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.1.1/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.1/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.2.1/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.2/Symbols/usr/lib/libobjc.A.dylib /Developer/Platforms/iPhoneOS.platform/DeviceSupport/3.0 (7A341)/Symbols/usr/lib/libobjc.A.dylib]...--[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0 (5A345)/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0 (5A347)/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0.1 (5B108)/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.0.2 (5C1)/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.1.1/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.1/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.2.1/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/2.2/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH --[/Developer/Platforms/iPhoneOS.platform/DeviceSupport/3.0 (7A341)/Symbols/usr/lib/libobjc.A.dylib] -- NO MATCH NOT searching in Spotlight for dsym with UUID of /usr/lib/libobjc.A.dylib ## Warning: Can't find any unstripped binary that matches version of /usr/lib/libobjc.A.dylib Here's an example of the crash report after running it through symbolicatecrash: Thread 0 Crashed: 0 libSystem.B.dylib 0x31dc476c 0x31d46000 + 517996 1 libSystem.B.dylib 0x31dc4755 0x31d46000 + 517973 2 Foo 0x00053075 uncaught_exception_handler + 21 3 CoreFoundation 0x3028f65f 0x301fd000 + 599647 4 libobjc.A.dylib 0x30013693 0x3000c000 + 30355 5 libstdc++.6.dylib 0x374ccc2d 0x3748a000 + 273453 6 libstdc++.6.dylib 0x374ccc81 0x3748a000 + 273537 7 libstdc++.6.dylib 0x374ccd4d 0x3748a000 + 273741 8 libobjc.A.dylib 0x300135ff 0x3000c000 + 30207 9 CoreFoundation 0x30222f2d 0x301fd000 + 155437 10 CoreFoundation 0x30222ecb 0x301fd000 + 155339 11 Foundation 0x30521e33 0x30501000 + 134707 12 Foundation 0x30570d47 0x30501000 + 458055 13 Foo 0x0000a1db -[Bar barfoo] (Bar.m:1617) 14 Foo 0x00032f73 -[MyViewController foobar] (MyViewController.m:727) 15 Foo 0x000329b9 -[MyViewController foobar] (MyViewController.m:666) 16 Foo 0x00031fab -[MyViewController tabBar:tabSelected:] (MyViewController.m:440) 17 Foo 0x00068d41 -[TTTabBar setSelectedTabIndex:] (TTTabBar.m:160) 18 Foo 0x00068ca3 -[TTTabBar setSelectedTabView:] (TTTabBar.m:142) 19 Foo 0x000689cf -[TTTabBar tabTouchedUp:] (TTTabBar.m:83) 20 CoreFoundation 0x302552f9 0x301fd000 + 361209 21 UIKit 0x3094d101 0x308ed000 + 393473 22 UIKit 0x3094d0a1 0x308ed000 + 393377 23 UIKit 0x3094d073 0x308ed000 + 393331 24 UIKit 0x3094cdcd 0x308ed000 + 392653 25 UIKit 0x309779c1 0x308ed000 + 567745 26 UIKit 0x30977011 0x308ed000 + 565265 27 UIKit 0x309767d9 0x308ed000 + 563161 28 UIKit 0x30923613 0x308ed000 + 222739 29 UIKit 0x30923163 0x308ed000 + 221539 30 GraphicsServices 0x32045a4d 0x32041000 + 19021 31 CoreFoundation 0x30253041 0x301fd000 + 352321 32 CoreFoundation 0x30252771 0x301fd000 + 350065 33 GraphicsServices 0x32044b0f 0x32041000 + 15119 34 GraphicsServices 0x32044bbb 0x32041000 + 15291 35 UIKit 0x308f0363 0x308ed000 + 13155 36 UIKit 0x308ef121 0x308ed000 + 8481 37 Foo 0x00002097 main (main.m:13)

  Read the article

• HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

  - by GT

  The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

  Read the article

• HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

  - by GT

  The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

  Read the article

• Why would the Default Gateway constantly require resetting?

  - by Raven Dreamer

  I've had a (mostly) steady internet connection for the past two months. For the last hour, however, my connectivity has been dropping every 10 minutes or so, and must be reset. So far, I've always been able to fix the issue by running Windows network diagnostics (On Windows 7 64 bit), but the lack of constant internet is making it a pain to try and stream video, download games through steam, etc. Windows always reports a fix by "Resetting the Local Area Connector", telling me: Default Gateway Not Available. What's going on? Is the trouble on my end, or with my ISP? (Timewarner Cable) Things I've Tried: Reinstalling the motherboard's LAN drivers Manually setting a default gateway (gets cleared, reverts to default settings) Unplugged (Hard Reset) the router Unplugged / replugged ethernet cable.

  Read the article

• What happens when a consumer switch receives a VLAN-tagged Ethernet frame?

  - by netvope

  Suppose you connect a trunk port from a VLAN capable network switch to a (VLAN incapable) consumer-grade network switch via a direct cable. Now the former switch send the later switch a 802.1Q-tagged Ethernet frame. What should the later switch do? Drop the frame? Forward the frame? Undefined behavior? If the behavior is undefined, what is most probable? Edit: Thank you for your answers. To summarize, the behavior of the consumer switch depends on: How it handles frames with 0x8100 in the EtherType field1 How it handles jumbo frames, or frames with payload larger than 1500 bytes Wikipedia has a nice diagram comparing an untagged and a tagged Ethernet frame: There are reports that some consumer-grade switches pass VLAN-tagged frames just fine. 1 or more precisely, where an EtherType field is expected for non-tagged frames

  Read the article

• Dell PSU Compatibility: Dell Inspiron 530 (Desktop)

  - by ashes999

  I have an Inspiron 530 with a stock PSU. I need to upgrade it to meet my video card's needs (AMD HD6770), which demands at least 450W, to potentially fix BSODs with the latest version of the drivers (so claims AMD support). Now, I've heard conflicting reports about whether Dell uses special/proprietary PSUs. (Examples for aye and nay to special PSUs.) How exactly can I determine if a PSU is compatible with my PC, before buying it? I assume I will not be able to return it if it doesn't fit, or makes my computer explode in a fireball of doom.

  Read the article

• Oracle LogMiner (Unsupported Operation)

  - by Sarith

  Hi all, I'm currently using Oracle 11g on RHEL5. I'm digging to see what are in the archived log files. After I query from v$logmnr_contents, I see many transactions of UNSUPPORTED operation. What do these unsupported transactions mean? I think that it's the cause that make my database generates lots of archived logs. Moreover, I'm using global temporary table for generating reports. I discover that when I insert and delete from those temporary table, it also records in the archived log file. How to do to reduce those recorded transactions? Regards, Sarith

  Read the article

• Repeated Reporting Services Login issue when deploying through BIDS to a remote server

  - by Richard Edwards

  We are having a problem deploying a reporting services report to a sql reporting services computer that is configured in SharePoint Integrated mode. I can successfully deploy to the SharePoint document libraries set up for reports and data connections if I do it locally from the box that SharePoint and Reporting Services are deployed on. If I try and do the same thing with the exact same deployment properties from a remote box, I constantly get a Reporting Services Login dialog popping up and no combination of domain\username and password will work. I've even tried the machines local admin account and still nothing. Any ideas where to start looking?

  Read the article

• IIS 7 Using Domain Account for Application pool identity Invalid Password

  - by Luke Van Diest

  I have an asp.net website containing a WCF service that I am developing on a Windows 7 machine hosted with IIS 7. I am needing to connect to an instance of Reporting Services 2005 with the service, and have been getting 401 errors when trying to execute reports. So, I assume that I need to be running the IIS Application pool under a domain account. The problem is that when I try to change the identity to a domain account, I get the error message "The specified password is invalid. Type a new password." I've rechecked the password multiple times to make sure it is correct. The account I'm using has admin rights on the machine. I saw elsewhere to try running this command: aspnet_regiis.exe -GA domain\username which I did but it didn't help. What else do I need to do?

  Read the article

• DNS and DHCP not agreeing on an IP address

  - by Mr. Jefferson

  I'm having a problem where our Windows Server 2003 domain controller assigns my Windows 7 computer one IP address (x.x.x.75) via DHCP, but reports another (x.x.x.84) via DNS. This causes some interesting behavior on the network. If I change my adapter settings to get IP and DNS addresses from DHCP, I can access the internet, but no one on our network can access my computer. If I change my IP manually to what DNS says it is, I lose my internet access, but everyone can get to my computer again. I know that we have some old, invalid reverse DNS pointers hanging around (a reverse lookup on an IP address often gives more than one result, usually not including the one that is correct), so that could be contributing, but my problem is recent, and the invalid reverse pointers have been around a long time. What's going on, and how do I fix it?

  Read the article

• spawn-fcgi/ fast CGi php crashes without traces in logs, on Gentoo

  - by user39046

  Hello, I recently moved from apache to a Nginx/fastcgi solution, I had it running on a Fedora system and had no problems, but, since i moved all to Gentoo , the Spawn-fCGI / fastcgi php daemon dies, and i can't find out any errors reports on /var/log/messages , so i don't know why this happens. I've seen that fastcgi is somehow different from the fedora distro, on gentoo as it has different conf files and init.d startup scripts, Can someone help me make it more stable? The number of requests that i had isn't any different from the ones I had on fedora, so i use the default conf that comes with the distro..and in about some hours it simply dies... Thank you very much

  Read the article

• Unable to uninstall SQL Server express

  - by Joel Martinez

  When I try, I receive the following error message: A computer restart is required. You must restart this computer before installing SQL Server. Of course, I have restarted the computer :-) I'm not really sure how to proceed. The version that sql server reports when I query it is: SQL Server 10.0.1600.22 - RTM (Express Edition with Advanced ) Solved: As it turns out, I had to end up uninstalling logitech's quick cam pro software. Although the fix below did not directly resolve it, the value of that registry key led me to discovering the solution by querying for it online :-) thanks!!!

  Read the article

• Nginx with postfix not sending mail - from address appearing wrong

  - by Adripants

  I am using a php form to send email. The script reports success, but the mail never arrives. The tail of the mail log shows: Nov 22 01:24:25 contra postfix/pickup[1195]: 0CC1B119A53: uid=100 from=<nginx> Nov 22 01:24:25 contra postfix/cleanup[1320]: 0CC1B119A53: message-id=<[email protected]> Nov 22 01:24:25 contra postfix/qmgr[1196]: 0CC1B119A53: from=<[email protected]>, size=363, nrcpt=1 (queue active) Just wondering where this from address is coming from and if thats why mails aren't arriving.

  Read the article

• transient DNS issues with certain sites in Snow Leopard

  - by ceejayoz

  I'm having a rather bizarre DNS issue with Snow Leopard. Certain sites - MSNBC.com being the most noticeable for me - have an odd issue with DNS, in all browsers. After not visiting the site after a while (30 minutes or so), the first attempt to access MSNBC.com results in a DNS error. Refreshing 1-5 times resolves the issue until the next ~30 minute period of inactivity. Seen this on three separate Macs at this point. One from-the-factory Snow Leopard install, two upgrades. Most sites are just fine. I Google and found other reports of the same thing with MSNBC, but no solutions.

  Read the article

• What consequences to take from what i read in logfiles?

  - by Helene Bilbo

  Since some weeks i manage my first Webserver, a Seaside application behind an Apache proxy on Linode, and i installed logwatch to send me daily logs. Where can i get information on when i have to act as a consequence of what i read in these logwatch reports? For example i read that all kinds of people try to login on funny nonexisting accounts or all kinds of webcrawlers test for nonexisting cms login pages, some ip adresses get banned and unbanned by fail2ban... I assume that's normal? Is it? But how do i know that i probably have to do something? What do i look for in the logs?

  Read the article

• What comment-spam filtering service works?

  - by Charles Stewart

  From an answer I gave to another question: There are comment filtering services out there that can analyse comments in a manner similar to mail spam filters (all links to the client API page, organised from simplest API to most complex): Steve Kemp (again) has an xml-rpc-based comment filter: it's how Debian filters comments, and the code is free software, meaning you can run your own comment filtering server if you like; There's Akismet, which is from the WordPress universe; There's Mollom, which has an impressive list of users. It's closed source; it might say "not sure" about comments, intended to suggest offering a captcha to check the user. For myself, I'm happy with offline by-hand filtering, but I suggested Kemp's service to someone who had an underwhelming experience with Mollom, and I'd like to pass on more reports from anyone who has tried these or other services.

  Read the article

• Ubuntu 12.04 transmission-daemon and zfsonlinux: bad file descriptor and corrupt pieces

  - by Ivailo Karamanolev

  I'm running a Ubuntu 12.04 with zfsonlinux and transmission-daemon. The issues: sporadic Bad File Descriptor and Piece #xxx is corrupt errors. After I recheck the torrent, everything seems fine. That happens only when downloading: once it's in seeding mode. This only happens after the torrent client has been running for some time. I installed zfsonlinux from the offical stable ppa (https://launchpad.net/~zfs-native/+archive/stable). I previously tried running transmission-daemon from the Ubuntu repository, but since I've switched to building the latest transmission from source with the latest libevent (all stable) - same thing. I've seen bug reports (https://trac.transmissionbt.com/ticket/4147) for that issue, but none of them seem to have a solution. How can I fix these errors, or at least understand where they come from and what I can do to rectify the issue?

  Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >