Search Results

Search found 98288 results on 3932 pages for 'user interface'.

Page 83/3932 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• FreeBSD high load loopback interface

  - by user1740915

  I have a problem with a FreeBSD server. There is a FreeBSD 9.0 amd64, two network cards em1 (internet), em0 (local network) configured firewall ipfw, natd, squid (not transparent), the server acts as a gateway for access to the Internet. Next problem: upload via squid is very low. At this moment I see next: natd, dhcpd load the cpu at that time when uploading through squid and there are a lot of traffic through the loopback interface. ipfw show output 0100 655389684 36707144666 allow ip from any to any via lo0 00200 0 0 deny ip from any to 127.0.0.0/8 00300 0 0 deny ip from 127.0.0.0/8 to any 00400 0 0 deny ip from any to ::1 00500 0 0 deny ip from ::1 to any 00600 4 292 allow ipv6-icmp from :: to ff02::/16 00700 0 0 allow ipv6-icmp from fe80::/10 to fe80::/10 00800 1 76 allow ipv6-icmp from fe80::/10 to ff02::/16 00900 0 0 allow ipv6-icmp from any to any ip6 icmp6types 1 01000 0 0 allow ipv6-icmp from any to any ip6 icmp6types 2,135,136 01100 1615 76160 deny ip from 192.168.1.1 to any in via em1 01200 0 0 deny ip from 199.69.99.11 to any in via em0 01300 46652 3705426 deny ip from any to 172.16.0.0/12 via em1 01400 3936404 345618870 deny ip from any to 192.168.0.0/16 via em1 01500 4 336 deny ip from any to 0.0.0.0/8 via em1 01600 4129 387621 deny ip from any to 169.254.0.0/16 via em1 01700 0 0 deny ip from any to 192.0.2.0/24 via em1 01800 917566 33777571 deny ip from any to 224.0.0.0/4 via em1 01900 147872 22029252 deny ip from any to 240.0.0.0/4 via em1 02000 1132194739 1190981955947 divert 8668 ip4 from any to any via em1 02100 3 248 deny ip from 172.16.0.0/12 to any via em1 02200 35925 2281289 deny ip from 192.168.0.0/16 to any via em1 02300 1808 122494 deny ip from 0.0.0.0/8 to any via em1 02400 3 174 deny ip from 169.254.0.0/16 to any via em1 02500 0 0 deny ip from 192.0.2.0/24 to any via em1 02600 0 0 deny ip from 224.0.0.0/4 to any via em1 02700 0 0 deny ip from 240.0.0.0/4 to any via em1 02800 960156249 1095316736582 allow tcp from any to any established 02900 64236062 8243196577 allow ip from any to any frag 03000 34 1756 allow tcp from any to me dst-port 25 setup 03100 193 11580 allow tcp from any to me dst-port 53 setup 03200 63 4222 allow udp from any to me dst-port 53 03300 64 8350 allow udp from me 53 to any 03400 417 24140 allow tcp from any to me dst-port 80 setup 03500 211 10472 allow ip from any to me dst-port 3389 setup 05300 77 4488 allow ip from any to me dst-port 1723 setup 05400 3 156 allow ip from any to me dst-port 8443 setup 05500 9882 590596 allow tcp from any to me dst-port 22 setup 05600 1 60 allow ip from any to me dst-port 2000 setup 05700 0 0 allow ip from any to me dst-port 2201 setup 07400 4241779 216690096 deny log logamount 1000 ip4 from any to any in via em1 setup proto tcp 07500 21135656 1048824936 allow tcp from any to any setup 07600 474447 35298081 allow udp from me to any dst-port 53 keep-state 07700 532 40612 allow udp from me to any dst-port 123 keep-state 65535 1990638432 1122305322718 allow ip from any to any systat -ifstat when uploading via squid Load Average ||| Interface Traffic Peak Total tun0 in 79.507 KB/s 232.479 KB/s 42.314 GB out 2.022 MB/s 2.424 MB/s 59.662 GB lo0 in 4.450 MB/s 4.450 MB/s 43.723 GB out 4.450 MB/s 4.450 MB/s 43.723 GB em1 in 2.629 MB/s 2.982 MB/s 464.533 GB out 2.493 MB/s 2.875 MB/s 484.673 GB em0 in 240.458 KB/s 296.941 KB/s 442.368 GB out 512.508 KB/s 850.857 KB/s 416.122 GB top output PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 66885 root 1 92 0 26672K 2784K CPU3 3 528:43 65.48% natd 9160 dhcpd 1 45 0 31032K 9280K CPU1 1 7:40 32.96% dhcpd 66455 root 1 20 0 18344K 2856K select 1 119:27 1.37% openvpn 16043 squid 1 20 0 44404K 17884K kqread 2 0:22 0.29% squid squid.conf cat /usr/local/etc/squid/squid.conf # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localnet http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 192.168.1.1:3128 # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/squid/cache 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/squid/cache I understand that the traffic passes through the SQUID several times. But can not find why.

  Read the article

• exchange server 2010 Outlook Web Access - Exchange Control Panel WEB Interface

  - by Aceth

  from what i can gather the mailbox bit of the web interface works fine.. when any of the users go to options (top right) and try to use some of the features such as the Organise Mail Delivery Reports to find messages etc... it comes up with a message .. "An item with the same key has already been added" I've looked in the event viewer and i think its this error - Watson report about to be sent for process id: 7016, with parameters: E12IIS, c-RTL-AMD64, 14.00.0639.021, ECP, ECP.Powershell, https://x.x.x.x/ecp/PersonalSettings/Accounts.svc/GetList, UnexpectedCondition:ArgumentException, c09, 14.00.0639.021. ErrorReportingEnabled: False and Request for URL 'https://x.x.x.x/ecp/PersonalSettings/Accounts.svc/GetList' failed with the following error: System.ArgumentException: An item with the same key has already been added. at System.ServiceModel.AsyncResult.End[TAsyncResult](IAsyncResult result) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.End(IAsyncResult result) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.ExecuteSynchronous(HttpApplication context, Boolean flowContext) at Microsoft.Exchange.Management.ControlPanel.WebServiceHandler.ProcessRequest(HttpContext context) at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) I've tried googling but no luck that's relevant :(

  Read the article

• Getting network interface device name in powershell

  - by Grant

  I needed a powershell 2 script to get the name and device name of each interface like it is shown in network connections in control panel. Should be easy... $interfaces = Get-WmiObject Win32_NetworkAdapter $interfaces | foreach { $friendlyname = $_ | Select-Object -ExpandProperty NetConnectionID $name = $_ | Select-Object -ExpandProperty Name } However, $name comes back as "Broadcom BCM5709C NetXtreme II GigE (NDIS VBD Client)", whereas in control panel it shows "Broadcom BCM5709C NetXtreme II GigE (NDIS VBD Client) #69", because there are multiple cards. I can't find that number anywhere in the properties. How can I get both the Name and Device Name, exactly as shown in Network Connections, in powershell 2 on windows server 2008 r2?

  Read the article

• Utilize two gateways on the same network same interface with load balancing

  - by RushPL

  My setup is two ISPs on a single interface and single network. I can either set my default gateway to 192.168.0.1 or 192.168.1.250 and either work. My desire is to utilize both of them with some load balancing. I have tried to follow the advice given in here http://serverfault.com/a/96586 #!/bin/sh ip route show table main | grep -Ev '^default' \ | while read ROUTE ; do ip route add table ISP1 $ROUTE done ip route add default via 192.168.1.250 table ISP1 ip route add default via 192.168.0.1 table ISP2 iptables -t mangle -A PREROUTING -j CONNMARK --restore-mark iptables -t mangle -A PREROUTING -m mark ! --mark 0 -j ACCEPT iptables -t mangle -A PREROUTING -j MARK --set-mark 10 iptables -t mangle -A PREROUTING -m statistic --mode random --probability 0.5 -j MARK --set-mark 20 iptables -t mangle -A PREROUTING -j CONNMARK --save-mark Now then I do "traceroute somehost" repeatedly I can only get route through my default route which is 192.168.1.250. Shouldn't the packets change routes in a random manner? How to debug it?

  Read the article

• ip routes to specific interface

  - by user65053

  I am trying to figure out how to get all traffic to 10.8.78.* to connect using interface ppp0 when available how would I properly handle this (centos) and can I fall back on eth0 when pp0 is not up? /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 69.19.219.69 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Cant register this user

  - by holgero

  I wanted to ask this question on meta, but it said, I have to log in first (which is where I have the problem!) I answered a question with this user. But when I tried to register and click on the stack exchange icon, it only displays three dots (animated) and never comes back. I suspected a firefox problem so I tried firefox on windows: And yes, I was able to create an account linked with my other accounts ( http://unix.stackexchange.com/users/27867/holgero and http://stackoverflow.com/users/1779245/holgero ) when I ran the latest firefox version under windows 7 in a virtual box. Then I upgraded my linux firefox to the newest version and deleted the other account under windows again. But still I cannot register this account ( http://superuser.com/users/177338/holgero ). On unix.stackexchange or stackoverflow I never had any problems with the registration, superuser seems to be different. So, how do I register this user and have it linked with my other stackexchange accounts?

  Read the article

• How to forward connection from one interface to another under linux

  - by Daniel

  Hi, I have linux box which has two network interface, eth0, eth1. from eth1 I can access an internal website, say under port 8080. from outside the box, I can't access that network. my question is, is there a way I set up something so from outside the box, there appears to be a web server running in port 8080 and when I connect to it, it automatically forwards to eht1 the internal site? I tried to enable ip forward and add a static route, but it doesn't work. thanks.

  Read the article

• Keepalived with apache unable to bind interface on Backup server

  - by davideagle

  I have two debian 6 servers running keepalived 1.1.20 with one server acting as a Master and the other as a Backup. Both servers host apache 2.4 that have a global Listener on all interfaces on port 80 (Listen *:80) how ever I have some sites that require a listener for port 443 (SSL) and that is configured for each VirtualHost in the Apache config since I do not want every VirtualHost to listen on port 443. The problem is when I try to start Apache on the Backup machine that does not hold the virtual interface the VirtualHost is supposed to be listening on, I get AH00072: make_sock: could not bind to address 1.1.1.1:443. I know this is expected behavior of Apache. The real question is are there any known workarounds or solutions to this scenario?

  Read the article

• Trouble creating FTP in Server 2008

  - by Saariko

  I have been trying to create an FTP server on my new Server 2008. I have been following both (very detailed and highly published here guides) For setting up using IIS Manager http://learn.iis.net/page.aspx/321/configure-ftp-with-iis-7-manager-authentication/ and For anonymous FTP http://www.trainsignaltraining.com/windows-server-2008-ftp-iis7 I am able to log as an anonymous user. My need is to use a named user, so I need to use the IIS Manager. I get error 530 when trying to log as a user. Connected to 127.0.0.1. 220 Microsoft FTP Service User (127.0.0.1:(none)): ftpmanager 331 Password required for ftpmanager. Password: 530-User cannot log in. Win32 error: Logon failure: unknown user name or bad password. Error details: Filename: Error: 530 End Login failed. ftp> I can not learn from this message anything. My password is set to: 1234 (so I don't think I make a mistake here - testing purposes only ofc) Thank you. Note - I went over other posts on SE that I read, and couldn't get the result: IIS7 Windows Server 2008 FTP -> Response: 530 User cannot log in. FTP Error 530, User cannot log in, home directory inaccessible. Having trouble setting up FTP server on Windows Server 2008 EDIT I think I found some errors with the physical path. Going to Basic settings, and Test Connection on the physical path, gave me the following error: The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that \$ has Read access to the physical path. Then test these settings again. I am not sure which/whom should get access to the Root folder !? I want to point out, I managed to login with a domain user (change authorization and authentication methods) but this is NOT the requested solution. I checked to make sure that the FTP, folders, access is working properly. I am bit lost here. ==== More tries: I have enabled another Allow rule for ALL Users. I still get the same error. It seems that it doesn't matter if i use a correct or wrong password, I still get Error 530.

  Read the article

• Vmware server: Browser does not load user interface

  - by matnagel

  I have the latest vmware server isntalled on ubuntu 8.04 lts 64 bit. I access the user interface over this url, which matches my ip and port settings: https://10.1.1.99:11222/ui Sometimes it works in fierofox 3.6, but sometimes not. Same in Google Chrome. When it does not work, what happens is that the cert is checked, the browser is loading something, but the result is a white page. Sometimes the favicon of vmware (blue with 3 squares) appears, but only the white page. And sometimes it works. I reload many times, most of the time the whit epage appears again. On some days I succeed. But on many days not. I can give more info if someone tells me what is needed. Please help, we need this badly.

  Read the article

• how to have files created by CMS have the same ownership as SSH user

  - by Cam

  I am having difficulty on our ubuntu server whereby I have an SSH user that when I create files using this user the ownership is web_user:www-data The problem is when a file is uploaded or created using a content management system like joomla. When files are uploaded through Joomla - such as components / modules... The ownership is set to www-data:www-data This means that I need to then chown all new files to web_user:www-data so we can edit the files. Is there a way to set for a directory and sub-directories that all new files created have the ownership of web_user:www-data? Do I need to use something like setuid or setgid? Any help would be greatly appreciated.

  Read the article

• SharePoint Returning a 401.1 for a Specific User/Computer

  - by Joe Gennari

  We have a SharePoint Services 3.0 site set up supporting about 300 users right now. This report is isolated and has never been duplicated. We have one AD user who cannot log into the SharePoint site with his account from his machine and is subsequently returned a 401.1 error. If any other user tries to log on with their account from his machine, it works okay. If he moves to another machine and logs on, it works okay. The only solution to this point has been to install FireFox on the machine. When he authenticates with FF, everything is okay. Remedies tried so far: Cleared cookies/cache Turned off/on Integrated Windows Authentication in IE Downgraded IE 8 to IE 6 Removed site from Intranet Sites zone Renamed the machine Disjoined/Rejoined Domain

  Read the article

• Cisco ASA 5505 inside interface multiple ip addresses

  - by Oneiroi

  I have an issue this morning where I want to be able to assign multiple ip addresses to the inside interface to facilitate an ip range migration for an office. Namely from a 192.168.1.x range to the new range, with the minimum of interruption for those working in the office. (New DHCP leases will use the new range, whilst those still on the 192.168.1.x range can continue to work until their lease is renewed). However I can not for the life of me figure out how to achieve this, trying to create multiple interfaces for the job leads to complaints about the license only allowing 2 active interfaces. Any suggestions? thanks in advance.

  Read the article

• Windows XP - non-user input data filter message after installing wireless keyboard & mouse

  - by James

  After I installed MS wireless keyboard and mouse and associated software, I started getting this annoying message titled "Hardware installation" telling me the software I am trying to install did not pass the XP logo tests. The software is for "HID non-user input data filter" and I have two options Continue anyway or stop installation. Now, if I try to continue the installation fails, if stop installing another message pops up with a little mouse logo and the whole process repeats itself. after I am done with that message a third dialog appears. This is happening every time I boot up my PC (a desktop), I tried following an advice I found in some forum and download windows update for ID non-user input data filter, but that installation failed as well. The thing is, that both keyboard and mouse are working fine Is there anyway to get past these dialogs ?

  Read the article

• Auto backup a user folder to a usb when usb is plugged in

  - by Azztech Computers

  I'm a computer technician and help customers everyday with their computers and smartphones and have a really basic (i think) request but dont know how to go about it. Customer always come in with broken phones, water damage, needing updates, or just want me to backup their information. I currently have a program that i use when i backup their computers it backups their iOS folder C:\Users\USER\AppData\Roaming\Apple Computer\MobileSync\Backup but what i want is a quick easy way to do this in customers houses. What i require is a way when i plug in a USB drive it AUTOMATICALLY searches for the folder and starts transferring the folder to a predefined folder on the USB drive. This was I can just plug it in and begin work on their computer or phone without the risk of losing their information. I'm sure there is a .bat/.ini file i could use but wondering if someone has already done this or something similar as I would need it to search all the USER folders not just the one I'm logged into. Thanks in advance

  Read the article

• When RDP as a Domain User, Smart Card Requested

  - by Paul

  My W8 machine is connected to domain zen. If I rdp to the W8 machine, I can log in as a local user without problems. If I try to log in as a domain user, I am prompted for a smart card instead of a password. Any ideas why? Note that Interactive login: require smart card is disabled in group policy: And here is the output from rsop.msc: Some additional information on this one. If my connecting machine is on the same domain/network as the W8 machine, then I am prompted for a password as usual. If the machine is remote, on a different domain, then I am prompted for a smart card. In addition, the machine I am connecting from that gets the smartcard prompt is an XP box. I haven't isolated exactly which of these factors triggers the different response.

  Read the article

• Install user scripts on Chrome

  - by Ahatius

  I created a JavaScript file, and named it test.user.js. I tried double clicking it, dragging & dropping it into Chrome and opening it with Chrome, but it won't install. I've already installed the dev version of Chrome, because it's stated somewhere that it's needed, but I can't get it to work. Then, I tried searching for a Chrome Greasemonkey addon, just to see that it was no further developed on, because Chrome has built-in support. Could someboy tell me what I have to do in order to get user scripts working on Chrome v21?

  Read the article

• User for Public Network

  - by user71604

  my computer can catch the signal for many Access Points for the same network, while the network has problem with internet connection in some APs and it's working in others "all APs have the same SSID" Please advice if as i user i can force my computer to connect with specific AP neither than to go with the one with higher power (through MAC adress or IP)?. I am sure that my computer catch more than 10 signals for APs"All with same SSID". I am using windows 7 home primume 64 bit. as a user i dont have access to the AP config.

  Read the article

• Which interface defines the physical address of a Dialup connection

  - by Debabratta

  I use dial up connection to connect to the Internet. When I type ipconfig/all in the command prompt it shows me a physical address along with description for the dial up connection. The description field shows WAN(PPP/SLIP)Interface. I want to know upon which this physical address depends? It depends on my computer or ISP. On changing my ISP, physical address for this dialup connection will change or remain same? Please give some idea.

  Read the article

• NETSH : Set default ip address for an interface with multiple Ips

  - by elarichi.y

  To test a load balancer I need to switch my ip address several time a day, and keep other ips routing trough other Wans. I run these commands in a batch script: netsh interface ip set address "Connexion au réseau local" static %ipd% 255.255.255.0 192.168.1.1 1 netsh in ip add address "Connexion au réseau local" %ips1% 255.255.255.0 netsh in ip add address "Connexion au réseau local" %ips2% 255.255.255.0 ipd: is the default ip I want to set (all traffic should go trough it). ips1 and ips2 : are the secondary ips I want to keep but what ever I do all traffic goes trough one IP !! (first one in the range) Please help me with this issue.

  Read the article

• Number of malicious attacks defended/done on the average user daily [closed]

  - by DalexL

  As a web hoster, it is very easy to notice the large amounts of exploit/abuse attempts done on my servers. Out of curiosity, how often are these attempts done on the average user? I'm assuming almost all of them are prevented just by simple security protocols in place by their browsers, local network, etc. How many attempts, on average, are committed against a single user daily through any method? (email, internet, downloads, etc.)? If known, what percentage of these things are blocked by the average users security? I tried googling but I was having a hard time getting the right search terms together.

  Read the article

• Jail user to home directory while still allowing permission to create and delete files/folders

  - by Sevenupcan

  I'm trying to give a client SFTP access to the root directory of their site on my server (Ubuntu 10.10) so they can manager their website themselves. While I have been successful in jailing a user to a directory and giving them SFTP access; they are only allowed to create and delete new files in sub directories (the directories they own). This means that I must give them access to the parent directory to the root of their site. How can I limit them to the root of their site (for example public_html) while still allowing them the ability create and delete files. All the tutorials I have read suggest that the root must be the owner of the user's home directory, which prevents them from write access inside that directory. I'm relatively new to managing my own server so any advice would be very grateful. Many thanks.

  Read the article

• Cannot access Nagios Web Interface

  - by Dominiqs

  After successfully installing Nagios core 3.4.1 (i also installed plug-in1.4.11) on our linux rhel 5.3 server i cannot login to the nagios web interface.I am running apache 2.2.3 I am using internet explorer 8 and also firefox 3.6.3 When i try to enter the url http//localhost/nagios/ on a desktop (on the same network as the Nagios server)it does seem to like it but if i try http//x.x.x.x/nagios/ (where x.x.x.x is the IP address of my nagios server) it likes it but then the authentication popup appears after entering the password and username(nagiosadmin) it throws the errors below The server x.x.x.x at Nagios access requires a username and password Warning this server is requesting that your username and password be sent in an insecure manner(basic authentication without a secure connection) After a few attempts i get error 401 authentication required error from internet explorer ;this server could not verify that you are authorized to access the document requested. Either you supplied the wrong credentials or your browser doesnt understand how to supply the credentials required. Help Please anyone..seems like an authentication issue

  Read the article

• disbale ssh for bnroot as root account

  - by user2916639

  i am beginner with centos - Linux i have dedicated server . my root username is bnroot . now i am taking ssh using this user. i want to disable ssh for bnroot. i have created user user name welcome i want take ssh login by welcome user then i ll use su - bnroot to get root privileges. i have set PermitRootLogin no , AllowUsers welcome IN /etc/sshd_config and after restarting sshd service . i take ssh login by welcome use then it is ok. but when i use su bnroot its prompt to password and i enter right passowrd it show su: incorrect password , i dont know where i am wrong . please help me here. changes i done - /etc/ssh/sshd_confid PermitRootLogin no AllowUsers welcome /etc/sudoers welcome ALL=(ALL) ALL getting error in /var/log/secure unix_chkpwd[666]: password check failed for user (bnroot) su: pam_unix(su:auth): authentication failure; logname=ewalletssh uid=503 euid=500 tty=pts/1 ruser=ewalletssh rhost= user=bnroot please let me know where i am wrong

  Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >