Search Results

Search found 2962 results on 119 pages for 'cisco vpn'.

Page 84/119 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

  • Have to run auto-negotiate between clients and switch - "old" switch works fine - "new" switch results in "port flapping"?

    - by ConfusedAboutSwitching
    I need some help understanding a problem we're having at work: We run Altiris/Deployment Solution and have to use auto-negotiate between client systems and our switches (Altiris apparently requires this for imaging, PXE boot and other functions). We have several areas with old wiring (Cat 3 & Cat 5) that have old 10/100 Cisco switches in them - and we can set these systems up to "auto/auto" (auto-negotiate on both the NIC and the switch port), and everything has been working fine. But - our networking crew changed out a couple of old switches for 10/100/1000 Cisco switches, and now - they are claiming that "auto/auto" won't work because the switches can't auto-negotiate the way the old 10/100 switches did - and that if we try to set the new gig switches to auto-negotiate, the switch port starts "port flapping", and shuts the port down. But - if we put the old switch back in - they work using "auto/auto" just fine - no port flapping. The networking crew is telling me that the problem is that we're putting "new switches" on "old wire", and that the old cabling can't/won't support the auto-negotiation with these new switches....??? There's something about this that doesn't make sense to me - can someone explain this to me? Or is our networking crew just doing something wrong in the configuration of these new switches? While will the old switches work "auto/auto", but the new switches won't?? HELP!!....and Thanks!! M

    Read the article

  • Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

    - by user12844
    I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

    Read the article

  • Static DHCP binding

    - by Alex
    Good time of day, SF people. I have created a manual DHCP binding entry on a Cisco router so that a client would always get leased to it. The clients wants to get the same address on both of his dual-boot linux systems. He tries to get an IP address leased and he succeeds on one of the dual-boot operating systems. When he reboots to another one he gets a lease for a completely different one. I don't get it. The MAC addresses are the same (we checked in ifconfig, so what could be happening here? Why is the router confused? Or is it something else? Also, how can I check DHCP server IP address who I have got an IP address from (on Linux)? Configuration on Cisco: ip dhcp pool MANUAL_BINDING0001 host 192.168.0.64 255.255.255.0 hardware-address dead.beef.1337 dns-server 192.168.8.11 default-router 192.168.0.254 domain-name verynicedomainigothere.cn PS. Is it mandatory to use client-name configuration line?

    Read the article

  • Connect to a network via Command Linke

    - by justasking
    Hi guys, I want to be able to connect to a network via command line in Windows. My goal is to script out remoting into my work computer. I hate having to always manually connect to the VPN connection and then rdping into my work machine. I want to just have a script which will do both of it for me. I know how to rdp via command line, I just need to know how to connect to my VPN via command line. Thanks!

    Read the article

  • PHP client for asmx service

    - by Carlos Mora
    A few days ago I was in charge of the development of some webServices for a client, the thing is that the client also asked for a php client that consumes the webservices. The service were published online on a server, with public access, right now I can see the wsdl from any computer, but when trying to consume it with PHP it shows me an error that says something about HTTP header and blablabla, that happened before I connected with a VPN to the server where the service is being hosted, after doing the VPN just by curiosity I reloaded the php client, and I don't know why... It did worked.... Q: Can anybody tell me why did this happened?

    Read the article

  • How can I dial the default connexion on Pocket PC 2003 ?

    - by Jalil
    I am working on a PPC2003 application. The devices on which the application has to run have a modem and VPN connection set. I want to automatically dial the system default "work" connection, which is the VPN one, which dial the modem one first. The user has another application who does automatically make the system dial the default connection. But I can't undertand how to do it from my Compact .NET application. I tried using OpenNETCF net package, but I could not make it work.

    Read the article

  • How can I dial the default connection on Pocket PC 2003 ?

    - by Jalil
    I am working on a PPC2003 application. The devices on which the application has to run have a modem and VPN connection set. I want to automatically dial the system default "work" connection, which is the VPN one, which dial the modem one first. The user has another application who does automatically make the system dial the default connection. But I can't undertand how to do it from my Compact .NET application. I tried using OpenNETCF net package, but I could not make it work.

    Read the article

  • Can not access network computers anymore

    - by Johny Skovdal
    Last Thursday (03/05/12) I got a new computer to be able to work from home. I plugged it, by cable, into the company network and installed most of the software needed for me to do so, by accessing a share on my stationary computer at work. I had no issues here what so ever, and everything just worked. Yesterday evening I tried accessing the company network trough Windows VPN, and while I was able to connect to the network, I was unable to connect to any computers on the network. I did, however, get an error when connecting, but I can't seem to get the error again, to get the details of the error message. Today I am sitting on the company network again, and now I can not access anything on the network like I could last Thursday, though I can ping all the computers I am attempting to access. Here is a list of details that might help in troubleshooting this issue (updated): List of observations / actions My computer is identical to another computer that has no issues. It is not on the domain but rather on the default workgroup, but this was not an issue last Thursday, so I am assuming it still is not. I am able to access my e-mail on the exchange server. I can connect to our TFS server from Visual Studio but not from Explorer. I can also connect to Database Servers and Remote Desktop. I can see several computers when browsing network computers, but I am unable to connect to any of them. When trying to connect to a computer I am consistently met with the error code "0x80070035" (network path not found). I also get the 0x80070035 error when double clicking the target computer from the Network UI. I am not met with a login dialog when trying to access a computer, as I should, since I am not on the domain. (I did login to both Exchange, Remote Desktop and TFS though) Between Thursday where it worked and Sunday evening where it did not, I have installed quite a few security updates, plus various tools etc. that I need for programming. I have tried accessing by computer name and ip and neither of them work. I can ping by computer name. I have deleted all (1 entry) stored network credentials. I am able to access my computer from the target computer. Client and Server can see each other on the network = Network Discovery is enabled. I am using the network profile "Work". When accessing the network through VPN, I am unable to get anything to work using computernames, but all of the above applies when using IP adresses instead of computername. I run Windows 7 Home Premium on my computer. Using powershell attempting to access a share I get the following error (ComputerName and ShareName being correct values of course): PS C:\Users\MyUser> cd \\ComputerName\ShareName Set-Location : Cannot find path '\\ComputerName\ShareName' because it does not exist. At line:1 char:3 + cd <<<< \\ComputerName\ShareName + CategoryInfo : ObjectNotFound: (\\ComputerName\ShareName:String) [Set-Location], ItemNotFoundException + FullyQualifiedErrorId : PathNotFound,Microsoft.PowerShell.Commands.SetLocationCommand However, ping'ing the same machine (ping ComputerName) from powershell I get response immediately. (As mentioned in the list of observations/actions, I tried the above with the IP address again on VPN, to get the same result) Conclusion So to sum up, pretty much the only thing I can not do, is access the other computers through browsing (explorer.exe, powershell, map networkdrive, etc.), which means that I am pretty much down to, that it is unable to resolve the path somehow, when trying to connect to other computers trough browsing, though the path gets resolved perfectly using all kinds of other services. Any recommendations as to what I can try next to resolve the issue? :)

    Read the article

  • How to use a different Ethernet connection

    - by SteveC
    I'm running a virtual machine at home which has a VPN connection to our main office, but I also want to connect to a share on another machine at home. When I check with IPCONFIG I can see two ethernet connections ... my work VPN ... Ethernet adapter Local Area Connection* 11: Connection-specific DNS Suffix . : Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : XXX.XXX.XXX.XXX Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : XXX.XXX.XXX.XXX and home local ... Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : lan Link-local IPv6 Address . . . . . : xxxx::xxxx:xxxx:xxxx:xxxxxxx IPv4 Address. . . . . . . . . . . : 192.168.1.70 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : What's weird is when I've been working before with a plugged-in ethernet cable I've not had any problem getting to the share? I can PING the other machine, but I can't access the share at ... \\othermachine\c$ I tried 'TRACERT` but that disappears off to the work network and eventually gets back to the local other machine after a few time-outs Is there anyway to "force" the connection to stay local ? UPDATE: the VPN is AEP SSL Tunnel

    Read the article

  • Routing a PPTP client and VMware Server instance running on the same box

    - by servermanfail
    I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

    Read the article

  • Importing PKCS#12 (.p12) files into Firefox From the Command Line

    - by user11165
    I’ve posted this question up on #Ubuntu and #Firefox Forums, and really could do with some help.. Anyone know where i could look or help with the answer. I’m hoping the power of social media will come through… I have a need to perform the following action: Firefox 3.6.x: Quote: open Edit - Preferences - Advanced - Encryption - View Certificates - Your Certificates - Import However i need the same functionality from the bash command line. So far I’ve established that the following command is supposed to be used: Quote: certutil -A -t “u,u,u” -d /home/df001/.mozilla/firefox/qe5y5lht.tc.default/ -n “mycert” -i client.p12 This executes with no isses, however, doesn’t show up in any Firefox Certificate store. However, I have noted that prior to running this command, i have a cert8.db key3.db and secmod.db file in the above folder. After running the command the certutil seems to have created a cert9.db, key4.db and pkcs12.txt file Listing the contents using the command: Quote: certutil -L -d sql:/home/df001/.mozilla/firefox/qe5y5lht.tc.default/ does seem to confirm my attempts of importing files into a certificate folder of some kind have worked. because i get Quote: Certificate Nickname Trust Attributes SSL,S/MIME,JAR/XPI Thawte SSL CA „ Go Daddy Secure Certification Authority „ Thawte SGC CA „ Entrust Certification Authority - L1C „ My Nero CT,C,c mynero P„ davidfield - Internet Widgits Pty Ltd u,u,u So, having tried this, and heading back over to the www, i cam across this command: Quote: pk12util -d /home/df001/.mozilla/firefox/qe5y5lht.tc.default/ -i client.p12 -n “David Field” -P “cert8.db” this again, appears to be importing something somewhere, however, again, Viewing certs from the Firefox interface doesn’t show the imported Cert. I’m surmising here on reading that the certutil and pk12util are creating a new NSS database, which firefox isn’t reading. So my question is, how can i get the p12 cert from the command line so it displays in the firefox Certificate manager interface? Why have i posted this here? Why not post on the firefox forum? Well i will copy and post the same question there as well, however the ability to use the command line to do this is important, as I have potentially 2000 machines which will need a user cert imported into firefox via a p12 file. I need to do this in the form of a script, i thought the hard part was going to be making the p12 file from the microsoft 2003 CA, turns out thats easy. I can’t just import via the GUI and copy over cert8.db x 2000, i can’t ask users to use the CA webinterface as its for VPN access, the users are off site, and they need the VPN to get to the cert server.. Is there any person out there who can help? By the way, i don't have the tor buttun installed.

    Read the article

  • What is the current "standard" for setting up a development environment that supports remote collaboration as well as secure version control?

    - by Andrew
    What is the current "standard" for setting up a development environment that supports remote collaboration as well as secure version control? Considering a virtual dedicated solution with vm for a web layer and a data layer, using VPN for each programmer. We're a small start-up that do both Microsoft and open-source development. Is there a set software tools or packages that are appropriate for a small shop and yet scalable? Thanks.

    Read the article

  • Methods to access US Netflix from Chromecast?

    - by lfk
    I need to access US Netflix using Chromecast but changing router configuration is not an option (I don't have access to the wireless router). On my laptop I use VPN, so one option is to use my laptop as a hotspot, but I don't always have cable connection for my laptop. Besides I was hoping to need only my iPad to use the Chromecast. Is there any other way or should I return the Chromecast while I still can?

    Read the article

  • What are different ways to reduce latency between a server and a web application? [closed]

    - by jjoensuu
    this is a question about a web application that provides SOAP web services. For the sake of this question, this web app is hosted on a server SERVER B which is located in California. We have an automated, scheduled, process running on a server SERVER A, located in New York. This scheduled process is supposed to send SOAP messages to SERVER B every so often, but this process typically dies soon after starting. We have now been told by the vendor that reason why the process dies is because of the latency between SERVER A and SERVER B. The data traffic is routed through many diffent public networks. There is no dedicated line between SERVER A and SERVER B. As a result I have been asked to look into ways to reduce the latency between SERVER A and SERVER B. So I wanted to ask, what are the different ways to reduce latency in a situation like this? For example, would it help to switch from HTTPS to some other secure protocol? (the thought here is that perhaps some other alternative would require fewer handshakes than HTTPS). Or would a VPN help? If a VPN would reduce the latency, how would it do that? NOTE: I am not looking for an explicit answer that would work in my specific situation. I am more like looking just for a simple list of what technologies could be used for this. I will still have to evaluate the technologies and discuss them internally with others, so the list would just be a starting point. Here I am assuming that there exists very few ways to reduce latency between two servers that communicate across public networks using HTTPS. Feel free to correct me if this assumption is wrong and please ask if there is a need for specific information. NOTE 2: A list of technologies is a specific answer to the question I stated in the title. NOTE 3: Its rather dumb to close this question when it is after all about me looking for information and furthermore this information can clearly be useful for others. Anyway luckily there are other sites where I can ask around. StackExchange seems to attached to their own philosophical principles. Many thanks

    Read the article

  • Connection to openVPN Access Server

    - by Beig
    we are using an openVPN Access Server and I would like to connect to it via the VPN network setting (network-manager-openvpn). I downloaded the client.ovpn and I can connect to the server via the command line: openvpn --script-security 2 --config client.ovpn How can I add the connection to the network manager? Which (key) entry is which? User Cert, CA Cert, Private Key? Here is an example of the client.ovpn http://nopaste.info/c10ec207f2.html Thanks in advance.

    Read the article

  • Operation times out trying to SSH outside LAN i.e. from internet to LAN no connection is established

    - by Pelle L
    I run Ubuntu 12.04 and have no success connecting with SSH from "Internet". The router is a TL-MR3420 which is set up to forward requests to one of the NIC's on ubuntu machine (which has in total 3 NICs). I can SSH from a client on the "local" network/LAN. The forward mechanism in the router seems to work. If I stop SSH service on the Ubuntu machine and instead start one on the windows machine - it works like a charm. I do not use the Std port 22 but that shouldn't be an issue as far as I understand - sine it works on the same port on the win machine. Since my public IS isn't static I use a dynDNS service but as said earlier the same setup works from the win machine. The router is located on 192.168.0.1 The Ubuntu NICs has the following IP: eth2 192.168.0.100 , eth1 192.168.0.101 , eth0 192.168.0.102 and I have forwarded the "outside" request to 192.168.0.100 In regards for firewall settings on the Ubuntu machine I have disabled the ufw and the command ufw status give status: inactive. I don't now it this is relevant information but teh command iptables --list give: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have tried to catch traffic with help of wireshark (a tool I'm not too used to use) and it seems as a few (3?) "requests" actually reaches the NIC but ... nothing happens. The syslog does not show any entries during these attempts. Perhaps it could be some routing issues but I have reached my level of competence and are stuck ... all help and support to get this sorted out is much appreciated. I'm new to Linux so please do not assume I have a configuration that is correct - but as I wrote earlier - if the client that initiate SSH is on the LAN it all works. PS:I have also tried to get VPN (PPP) working from Internet with no success - once again VPN works on the windows machine ... so my best guess is that this is related to how the ubuntu machine handles (IP) traffic and not the TL-MR3420 router or other network issues.

    Read the article

  • Tuesday at OpenWorld: Identity Management

    - by Tanu Sood
    At Oracle OpenWorld? From keynotes, general sessions to product deep dives and executive events, this Tuesday is full of informational, educational and networking opportunities for you. Here’s a quick run-down of what’s happening today: Tuesday, October 2, 2012 KEYNOTE: The Oracle Cloud: Oracle’s Cloud Platform and Applications Strategy 8:00 a.m. – 9:45 a.m., Moscone North, Hall D Leading customers will join Oracle Executive Vice President Thomas Kurian to discuss how Oracle’s innovative cloud solutions are transforming how they manage their business, excite and retain their employees, and deliver great customer experiences through Oracle Cloud. GENERAL SESSION: Oracle Fusion Middleware Strategies Driving Business Innovation 10:15 a.m. – 11:15 a.m., Moscone North - Hall D Join Hasan Rizvi, Executive Vice President of Product in this strategy and roadmap session to hear how developers leverage new innovations in their applications and customers achieve their business innovation goals with Oracle Fusion Middleware. CON9437: Mobile Access Management 10:15 a.m. – 11:15 a.m., Moscone West 3022 The session will feature Identity Management evangelists from companies like Intuit, NetApp and Toyota to discuss how to extend your existing identity management infrastructure and policies to securely and seamlessly enable mobile user access. CON9162: Oracle Fusion Middleware: Meet This Year's Most Impressive Customer Projects 11:45 a.m. – 12:45 a.m., Moscone West, 3001 Hear from the winners of the 2012 Oracle Fusion Middleware Innovation Awards and see which customers are taking home a trophy for the 2012 Oracle Fusion Middleware Innovation Award.  Read more about the Innovation Awards here. CON9491: Enhancing the End-User Experience with Oracle Identity Governance applications 11:45 a.m. – 12:45 p.m., Moscone West 3008 Join experts from Visa and Oracle as they explore how Oracle Identity Governance solutions deliver complete identity administration and governance solutions with support for emerging requirements like cloud identities and mobile devices. CON9447: Enabling Access for Hundreds of Millions of Users 1:15 p.m. – 2:15 p.m., Moscone West 3008 Dealing with scale problems? Looking to address identity management requirements with million or so users in mind? Then take note of Cisco’s implementation. Join this session to hear first-hand how Cisco tackled identity management and scaled their implementation to bolster security and enforce compliance. CON9465: Next Generation Directory – Oracle Unified Directory 5:00 p.m. – 6:00 p.m., Moscone West 3008 Get the 360 degrees perspective from a solution provider, implementation services partner and the customer in this session to learn how the latest Oracle Unified Directory solutions can help you build a directory infrastructure that is optimized to support cloud, mobile and social networking and yet deliver on scale and performance. EVENTS: Executive Edge @ OpenWorld: Chief Security Officer (CSO) Summit 10:00 a.m. – 3:00 p.m. If you are attending the Executive Edge at Open World, be sure to check out the sessions at the Chief Security Officer Summit. Former Sr. Counsel for the National Security Agency, Joel Brenner, will be speaking about his new book "America the Vulnerable". In addition, PWC will present a panel discussion on "Crisis Management to Business Advantage: Security Leadership". See below for the complete agenda. PRODUCT DEMOS: And don’t forget to see Oracle identity Management solutions in action at Oracle OpenWorld DEMOgrounds. DEMOS LOCATION EXHIBITION HALL HOURS Access Management: Complete and Scalable Access Management Moscone South, Right - S-218 Monday, October 1 9:30 a.m.–6:00 p.m. 9:30 a.m.–10:45 a.m. (Dedicated Hours) Tuesday, October 2 9:45 a.m.–6:00 p.m. 2:15 p.m.–2:45 p.m. (Dedicated Hours) Wednesday, October 3 9:45 a.m.–4:00 p.m. 2:15 p.m.–3:30 p.m. (Dedicated Hours) Access Management: Federating and Leveraging Social Identities Moscone South, Right - S-220 Access Management: Mobile Access Management Moscone South, Right - S-219 Access Management: Real-Time Authorizations Moscone South, Right - S-217 Access Management: Secure SOA and Web Services Security Moscone South, Right - S-223 Identity Governance: Modern Administration and Tooling Moscone South, Right - S-210 Identity Management Monitoring with Oracle Enterprise Manager Moscone South, Right - S-212 Oracle Directory Services Plus: Performant, Cloud-Ready Moscone South, Right - S-222 Oracle Identity Management: Closed-Loop Access Certification Moscone South, Right - S-221 For a complete listing, keep the Focus on Identity Management document handy. And don’t forget to converse with us while at OpenWorld @oracleidm. We look forward to hearing from you.

    Read the article

  • RouterOS on Hyper-V (v3/2012) - any way to get it working?

    - by TomTom
    Trying to set up a small VPN point to connect into a remote Hyper-V cluster using ROuterOS. Anyone got it working ON Hyper-V with the latest builds of RouterOS? It seems the legacy network adapter is not supported anymore either (or just broken). The platform is a Windows Server 2012 RC. This is not a high performance setup - the RouterOS wont do the routing for more than the backend administrative access, and the only real traffic we will see there is when ISO images for new operating systems are uploaded. Otherwise we will have possibly RDP traffic as well as web / http traffioc, but this is internal only (dashboards, some control panel). The server has no public business. So the price for non virtualized network cards is ok for me. After hooking up - ping just does not work. After some time I see in windows (arp -a on the command line), so I know that the Hyper-V side is set up properly. Just no packets arrived. I have turned off all protection on Hyper-V (or : not turned them on), so no MAC spoofing protection etc. in the Advanced page for the legacy adapters. Unless I can get it work I will have to resort to using a windows install as router / VPN endpoint, which introduces another OS into the fabric (we run all routers etc. so far on mikrotik in hardware, which is why I want this one to be RouterOS, too). And no, putting hardware there is NOT an option - the cost would be significant.

    Read the article

  • Alternative to robocopy /MIR

    - by Robin Day
    We run a number of web apps that store a lot of local data in small xml files. One part of our backup / recovery strategy is to produce a local mirror of the file system via a VPN to the hosting centre. The VPN connection is only via a 12Mbps ADSL and whilst there are a lot of files and directories, the actual number of files that changes is quite small. Although the bandwidth is probably an issue, I'm seeing results such as the output below. The robocopy /MIR took 5 hours to run yet only 30 mins to actually perform the copy. Does anyone have any suggestions as to ways to improve this. The 5 hours is now bordering on too slow and if we can't find a way to speed this up then we're going to have to come up with a completely different solution. Total Copied Skipped Mismatch FAILED Extras Dirs : 17625 6618 11007 0 0 0 Files : 1112430 1223 1111207 0 0 0 Bytes : 57.451 g 192.25 m 57.263 g 0 0 0 Times : 5:01:23 0:35:55 0:00:00 4:25:27 Speed : 93509 Bytes/sec. Speed : 5.350 MegaBytes/min. Ended : Fri Apr 16 05:54:23 2010

    Read the article

  • Can't get my OpenVpn client to connect

    - by Larry
    Hi Guys, I am trying to setup a test vpn between my home desktop and my laptop. So far I have got the server on the desktop to connect fine but I can not get my laptop to finish the connection. I have tried several different configurations and they all give me the same result. Obviously it has nothing to do with my Client configuration but possibly something on my laptop? Here is the message I get in the log when it stops then times out and restarts. Mon Oct 18 20:10:55 2010 UDPv4 link local: [undef] Mon Oct 18 20:10:55 2010 UDPv4 link remote: 74.190.29.236:1194 Mon Oct 18 20:11:55 2010 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Oct 18 20:11:55 2010 TLS Error: TLS handshake failed here are my configurations server.ovpn port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.1 255.255.255.252 ifconfig-pool-persist ipp.txt push "route 10.0.0.1 255.255.255.0" push "dhcp-option WINS 10.0.0.5" push "dhcp-option DNS 10.0.0.5" push "dhcp-option DOMAIN acme.com.local" keepalive 10 120 comp-lzo max-clients 1 persist-key persist-tun status openvpn-status.log verb 3 LArry.ovpn client proto udp dev tun remote doublel.hopto.org 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client1.crt key client1.key comp-lzo verb 3 dev tun local 206.162.148.9 remote 134.28.54.2 ifconfig 192.168.99.1 192.168.99.2 route 10.0.0.0 255.0.0.0 192.168.99.2 I just need a simple vpn for one user. Am I headed down the right path? Thanks, Larry

    Read the article

  • OpenVpn Iptables Error

    - by Mook
    I mean real newbie - linux here.. Please help me configuring my openvpn through iptables. My main goal here is to open port for regular browsing (80, 443), email (110, 25), etc just like isp does but i want to block p2p traffic. So I will need to open only few port. Here are my iptables config # Flush all current rules from iptables # iptables -F iptables -t nat -F iptables -t mangle -F # # Allow SSH connections on tcp port 22 (or whatever port you want to use) # iptables -A INPUT -p tcp --dport 22 -j ACCEPT # # Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT DROP #using DROP for INPUT is not always recommended. Change to ACCEPT if you prefer. iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # Accept packets belonging to established and related connections # iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # #Accept connections on 1194 for vpn access from clients #Take note that the rule says "UDP", and ensure that your OpenVPN server.conf says UDP too # iptables -A INPUT -p udp --dport 1194 -j ACCEPT # #Apply forwarding for OpenVPN Tunneling # iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT #10.8.0.0 ? Check your OpenVPN server.conf to be sure iptables -A FORWARD -j REJECT iptables -t nat -A POSTROUTING -o venet0 -j SNAT --to-source 100.200.255.256 #Use your OpenVPN server's real external IP here # #Enable forwarding # echo 1 > /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p tcp --dport 25 -j ACCEPT iptables -A INPUT -p tcp --dport 26 -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 110 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -L -v But when I connect to my vpn, i can't browsing and also got RTO on pinging yahoo, etc

    Read the article

  • one way routing

    - by user101531
    I have two computers connected with VPN, and some virtual machines on each. I want everything to see each other (that is basically 4 different networked machines). What I've not managed so far is that a computer on the one end to be visible to the other end. In tracert terms: 192.168.78.42>tracert 192.168.69.18 Tracing route to WIN-2K8R2 [192.168.69.18] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.78.17 2 * * * Request timed out. 3 217 ms 78 ms 78 ms WIN-2K8R2 [192.168.69.18] Trace complete. 192.168.78.42>tracert 192.168.69.112 Tracing route to 192.168.69.112 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.78.17 2 333 ms * 337 ms WIN-2K8R2 [192.168.86.22] 3/4/5 * * * Request timed out. 6 ^C 192.168.69.18>tracert 192.168.69.112 Tracing route to 192.168.69.112 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.69.112 Trace complete. 192.168.69.112>tracert 192.168.78.42 Tracing route to 192.168.78.42 over a maximum of 30 hops 1 1 ms * <1 ms 192.168.69.18 2 79 ms 77 ms 80 ms 192.168.86.21 3 80 ms 77 ms 81 ms 192.168.78.42 Trace complete. Note: the 4 machines are 192.168.69.112 (winXP), 192.168.69.18=192.168.86.22 (win2K8R2), 192.168.86.21=192.168.78.17 (Linux), 192.168.78.42 (win2K3). The VPN is a TAP openvpn connection between 192.168.86.21 and 192.168.86.22. I would say that the problem is in the win2K8 machine, but Windows networking is my weak point.

    Read the article

  • Samba Server Make Multiple User Permissions Profiles

    - by Scriptonaut
    I have a Samba file server running, and I was wondering how I could make multiple user accounts that have different permissions. For example, at the moment I have a user, smbusr, but when I ssh to the share, I can read, write, execute, and even navigate out of the samba directory and do stuff on the actual computer. This is bad because I want to be able to give out my IP so friends/family can use the server, but I don't want them to be able to do just anything. I want to lock the user in the samba share directory(and all the sub directories). Eventually I would like several profiles such as (smbusr_R, smbusr_RW, smbguest_R, smbguest_RW). I also have a second question related to this, is SSH the best method to connect from other unix machines? What about VPN? Or simply mounting like this: mount -t ext3 -o user=username //ipaddr/share /mnt/mountpoint Is that mounting command above the same thing as a vpn? This is really confusing me. Thanks for the help guys, let me know if you need to see any files, or need anymore information.

    Read the article

  • Samba Server Make Multiple User Permissions Profiles

    - by Scriptonaut
    I have a Samba file server running, and I was wondering how I could make multiple user accounts that have different permissions. For example, at the moment I have a user, smbusr, but when I ssh to the share, I can read, write, execute, and even navigate out of the samba directory and do stuff on the actual computer. This is bad because I want to be able to give out my IP so friends/family can use the server, but I don't want them to be able to do just anything. I want to lock the user in the samba share directory(and all the sub directories). Eventually I would like several profiles such as (smbusr_R, smbusr_RW, smbguest_R, smbguest_RW). I also have a second question related to this, is SSH the best method to connect from other unix machines? What about VPN? Or simply mounting like this: mount -t ext3 -o user=username //ipaddr/share /mnt/mountpoint Is that mounting command above the same thing as a vpn? This is really confusing me. Thanks for the help guys, let me know if you need to see any files, or need anymore information.

    Read the article

  • openvpn TCP/UDP slow SSH/SMB performance

    - by Petr Latal
    I have question about strange behavior of my openVPN configuration on Debian lenny. I have 2 server configs (one proto tcp-server based and one proto udp based). ISP bandwidth is 7Mbit/7Mbit. When I uses proto tcp-server my download server rate is fine around 6,4 Mbit/s, but upload rate is about 3Mbit/s. When I uses proto udp, my download server rate is around 3Mbit/s and upload rate around 6,4Mbit/s. I tried to handle the MTU, MSSFIX and cipher on/off on server and client configs to synchronize rates, but without solution. Here is TCP based SERVER config: mode server tls-server port 1194 proto tcp-server dev tap0 ifconfig 11.10.15.1 255.255.255.0 ifconfig-pool 11.10.15.2 11.10.15.20 255.255.255.0 push "route 192.168.1.0 255.255.255.0" push "dhcp-option DNS 192.168.1.200" push "route-gateway 11.10.15.1" push "dhcp-option WINS 192.168.1.200" route-up /etc/openvpn/routeup.sh duplicate-cn ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh2048.pem log-append /var/log/openvpn.log status /var/run/vpn.status 10 user nobody group nogroup keepalive 10 120 comp-lzo verb 3 script-security 3 plugin /usr/lib/openvpn/openvpn-auth-pam.so system-auth persist-tun persist-key mssfix cipher BF-CBC Here is UDP based SERVER config: port 1194 proto udp dev tun0 local xx.xx.xx.xx server 11.10.15.0 255.255.255.0 ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh2048.pem log-append /var/log/openvpn.log status /var/run/vpn.status 10 user nobody group nogroup keepalive 10 120 comp-lzo verb 3 duplicate-cn script-security 3 plugin /usr/lib/openvpn/openvpn-auth-pam.so system-auth persist-tun persist-key tun-mtu 1500 mssfix 1212 client-to-client ifconfig-pool-persist ipp.txt Here is TCP/UDP based windows CLIENT config: remote xx.xx.xx.xx --socket-flags TCP_NODELAY tls-client port 1194 proto tcp-client #proto udp dev tap #dev tun pull ca ca.crt cert latis.crt key latis.key mute 0 comp-lzo adaptive verb 3 resolv-retry infinite nobind persist-key auth-user-pass auth-nocache script-security 2 mssfix cipher BF-CBC

    Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >