Search Results

Search found 2490 results on 100 pages for 'hp uft'.

Page 84/100 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• NVIDIA X Server TwinView isses with 2 GeForce 8600GT cards

  - by Big Daddy

  Full disclosure, I am relatively new to Linux and loving the learning curve but I am undoubtedly capable of ignorant mistakes I have a rig I am building for my home office desktop. The basics: Gigabyte MB AMD 64bt processor Ubuntu 12.04 64bit two Nvidia GeForce 8600GT video cards using a SLI bridge two 22" DVI input HP monitors So here is my issue (it is driving me nuts) with X Server. If I plug both monitors into GPU 0 X Server auto configures TwinView and all is grand, works like a charm, though both are running off of GPU 0. If I plug one monitor into GPU 0 and one monitor into GPU 1, X Server enables the monitor on GPU 0, sees but keeps the monitor on GPU 1 disabled. My presumption (we all know the saying about presumptions) is that all I would have to do is select the disabled monitor on GPU 1 and drop down the Configure pull down and select TwinView...problem is when the monitors are plugged in this way, the TwinView option is greyed out and can not be selected. What am I not understanding here? Is there some sort of configuration I need to do elsewhere for Ubuntu to utilize both GPU's? Any help will be most appreciated, thanks in advance.

  Read the article

• Laptop runs HOT after 12.10 upgrade!

  - by dinkelk

  I was running 12.04 for 6 months, my laptop ran almost silently and cool enough to hold on my lap. I updated to 12.10 and now my computer gets too hot to hold on my lap and the fan is constantly running on full blast. This is the output of sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +84.0°C (crit = +99.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +84.0°C (high = +86.0°C, crit = +100.0°C) Core 0: +74.0°C (high = +86.0°C, crit = +100.0°C) Core 1: +72.0°C (high = +86.0°C, crit = +100.0°C) Core 2: +75.0°C (high = +86.0°C, crit = +100.0°C) Core 3: +84.0°C (high = +86.0°C, crit = +100.0°C) radeon-pci-0100 Adapter: PCI adapter temp1: +76.0°C I have an HP Pavilion dv6, i7, amd radeon graphics. Please let me know if you need additional information. What could be different between the two Ubuntu additions that caused such a drastic change? Edit 1: Per @Paul's suggestion, I ran htop to try to narrow down the problem. Here is the result! This is about 10 minutes after boot-up, htop, yakuake, and a chrome page with 1 tab opened to this question are all that I have manually opened. The most taxing program to the CPU is htop itself. I think that the problem must lie elsewhere; my temps are already up to ~65C for the CPU and ~69C for the GPU, with nearly 0% CPU usage.

  Read the article

• Lubuntu customized cdrom installation crashes

  - by SBarve

  I have created customized live cd of lubuntu and it is customized using uck. After burning the CDROM and using the cdrom for installation of same CD the installation works fine on HP desktop but it fails on Dell desktop. Here is the error. Can someone help to sort out this error. We are sorry; the installer crashed. After you close this window, we will allow you to file a bug report using the integrated bug reporting tool. This will gather information about your system and your installation process. The details will be sent to our bug tracker and a developer will attend to the problem as soon as possible. Traceback (most recent call last): File "/usr/lib/ubiquity/plugins/ubi-timezone.py", line 173, in geoname-cb for result in json.loads (message.response_body.data): File "/usr/lib/python2.7/json/_init_.py", line 326, in loads return_default_decoder.decode(s) File "/usr/lib/python2.7/json/decoder.py", line 366, in decode obj, end=self.raw_decode(S, idx=_w(S,0).end ()) File "/usr/lib/python2.7/json/decoder.py", line 384, in raw_decode raise ValueError ("No JSON object could be decoded") ValueError: No JSON object could be decoded.

  Read the article

• Running Ubuntu Server from a USB key / thumb drive (being mindful of flash's write limitations)

  - by andybjackson

  Having become disillusioned with hacking Buffalo NAS devices, I've decided to roll my own home server. After some research, I have settled on an HP Proliant Microserver with Ubuntu Server and a ZFS RAID-Z array for data. I settled on this configuration after trying and regretfully rejecting FreeNAS because the Logitech Media Server (LMS) software isn't available on the AMD64 flavour of this platform and because I think Debian/Ubuntu server is a better future-proof platform. I considered Open Media Vault, but concluded that it isn't quite yet ready for my purposes. That said, FreeNAS does include the option to run itself off a 2GB+ flash device like USB key or thumb drive. Apparently FreeNAS is mindful of the write limitations of flash devices and so creates virtual disks for running the OS, writing only the required configuration information back to flash. This would give me an extra data drive slot. Q: Can Ubuntu Server be configured sensibly to run off a flash device such as a USB key/thumb drive? If so, how? The write limitations of flash should be accounted for.

  Read the article

• How do I get 1366x768 resolution on 12.04?

  - by Megan

  I am on an HP Envy 14, and the proper resolution that I should be using is 1366x768. This is not an option and I am stuck on 1024x768. I am using Linux 12.04. lspci | grep VGA: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Madison [Radeon HD 5000M Series] I've tried to add the resolution as a mode in xorg.conf but that does not work. Please any help would be appreciated. I'm new to Linux and just got my dual boot working but this resolution issue is killing me. Edit1 I just tried using the xrandr command: xrandr --newmode "1368x768_60.00" 85.25 1368 1440 1576 1784 768 771 781 798 -hsync +vsync But I get an error: xrandr: Failed to get size of gamma for output default Edit2 lsmod returns the following: Module Size Used by vesafb 13844 1 rfcomm 47604 12 bnep 18281 2 parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 arc4 12529 2 joydev 17693 0 hid_logitech_dj 18594 0 i915 472941 5 uvcvideo 72627 0 usbhid 47199 1 hid_logitech_dj hid 99559 2 hid_logitech_dj,usbhid psmouse 87692 0 iwlwifi 332525 0 mac80211 506816 1 iwlwifi videodev 98259 1 uvcvideo snd_hda_codec_idt 70795 1 mei 41616 0 btusb 18288 2 v4l2_compat_ioctl32 17128 1 videodev hp_accel 25976 0 lis3lv02d 19876 1 hp_accel hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi input_polldev 13896 1 lis3lv02d drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 serio_raw 13211 0 snd_hda_intel 33773 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec bluetooth 180104 23 rfcomm,bnep,btusb cfg80211 205544 2 iwlwifi,mac80211 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec mac_hid 13253 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_ra wmidi,snd_seq,snd_timer,snd_seq_device wmi 19256 1 hp_wmi video 19596 1 i915 intel_ips 18174 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 I have installed ATI/AMD proprietary FGLRX graphics driver. But there is another one called ATI/AMD proprietary FGLRX graphics driver (post-release updates) which I have trouble installing because it gives me an error and tells me to look at some sort of jockey log.

  Read the article

• Connecting / disconnecting DisplayPort causes crash

  - by iGadget

  I wanted to file a bug about this using ubuntu-bug xserver-xorg-video-intel, but the system prompted my to try posting here first. So here goes :-) While the situation in Ubuntu 11.10 was still somewhat workable (see UI freezes when disconnecting DisplayPort), in 12.04 (using Unity 3D) it has gotten worse. The weird part is that during the 12.04 beta's, the situation was actually improving! I was able to successfully connect and disconnect a DisplayPort monitor without the system breaking down on me. But now with 12.04 final (with all updates), it's just plain terrible. When I now connect an external monitor using the DisplayPort connector on my HP ProBook 6550b, it only works sometimes. Most times (but not always!) the screen just goes blank and the system seems to crash (not even CTRL+ALT+F1 works anymore). Only a hard shutdown by keeping the power button pressed for several seconds and then a restart gets me out of this. I suspect the chances of the system crashing become higher as the system's uptime increases, especially when there have been one or more suspend-resume cycles (although I have also experienced this bug once from a cold boot). Disconnecting is roughly the same as with 11.10 (see issue mentioned above), with the difference that if I resume from suspend, I no longer have to do a CTRL+ALT+F1, ALT+F7 cycle to get my screen back. So what more can I try? Or should I just go ahead and file the bug anyway?

  Read the article

• OUCH! Laptop running SUPER HOT after 12.10 upgrade!

  - by dinkelk

  I was running 12.04 for 6 months, my laptop ran almost silently and cool enough to hold on my lap. I updated to 12.10 and now my computer gets too hot to hold on my lap and the fan is constantly running on full blast. This is the output of sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +84.0°C (crit = +99.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +84.0°C (high = +86.0°C, crit = +100.0°C) Core 0: +74.0°C (high = +86.0°C, crit = +100.0°C) Core 1: +72.0°C (high = +86.0°C, crit = +100.0°C) Core 2: +75.0°C (high = +86.0°C, crit = +100.0°C) Core 3: +84.0°C (high = +86.0°C, crit = +100.0°C) radeon-pci-0100 Adapter: PCI adapter temp1: +76.0°C I have an HP Pavilion dv6, i7, amd radeon graphics. Please let me know if you need additional information. What could be different between the two Ubuntu editions that caused such a drastic change? Edit 1: Per @Paul's suggestion, I ran htop to try to narrow down the problem. Here is the result! (left side of terminal) (right side of terminal) This is about 10 minutes after boot-up, htop, yakuake, and a chrome page with 1 tab opened to this question are all that I have manually opened. The most taxing program to the CPU is htop itself. I think that the problem must lie elsewhere; my temps are already up to ~65C for the CPU and ~69C for the GPU, with nearly 0% CPU usage.

  Read the article

• Dual-Boot Problem

  - by user171379

  I have a HP laptop that originally had Windows 7 OS on it, I partioned the drive and allocated 100gb (est.) for the ubuntu install. the install went fine i have ubuntu and windows 7 still on the computer. But I can not get the OS boot screen to show ubuntu as an OS. I can while start up pull up the start menu screen via ESC. Key and press F9 for Boot Device Options and get the boot manager screen and it lists... OS boot manager, Ubuntu (Hitachi HTS 543232A7A384), boot from EFI file, and Notebook Hard Drive... I can boot Ubuntu from this screen by selecting Ubuntu. But i would like to make it easier to access. The computer boot is not for myself otherwise it would not be a problem i would remove windows altogether. I would like to make it basically "User Friendly" if that's at all possible and make the OS boot screen show Ubuntu as a bootable OS as well as Windows 7. on the boot selection screen. Any help on this issue would be greatly appreciated, I've looked to see if i could find the answer and maybe i've overlooked something so here I am. Like i said i need it to be as user friendly as possible and force the user to choose windows 7 or ubuntu not send them into one or the other without them being allowed to choose. I can get any information you might need if necessary but i dont know exactly what you'll need other than what i've given. Ubuntu version is the 13.04 just so you know.

  Read the article

• Cannot view, use, or open CDs or DVDs in Ubuntu 12.04

  - by user67592

  I am fairly new to Ubuntu 12.04 and I have encountered a rather irritating problem. Whenever I insert a CD or DVD (whether it have data, music, movies, or nothing at all), nothing pops up saying "you have inserted a CD", "play with Rhythmbox?" etc. It doesn't show the CD in the launcher/dock or anything of the sort. This is especially peculiar because not only do I have a standard IDE built-in optical drive, but I have an external USB optical drive. Neither work. In addition, whenever I go to "Computer///" and I click (double click, right click, or even left click) on "CD/DVD Drive" nothing happens, when I right click and select "Open" nothing happens either [for either of the two drives (both are listed in Computer///)] And if I insert a blank disk and go to a disk burning program such as Brasero, and try to burn to the drive it detects no CDs or DVDs of any kind. I'm rather stumped and can't seem to find a question similar to this. :( Thanks for all your help in advance!! :) ~Preston Output of sudo lshw *-cdrom description: DVD-RAM writer product: CD/DVDW TS-H652M vendor: TSSTcorp physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 0414 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom description: DVD reader product: DVD Writer 300n vendor: HP physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/sr1 version: 1.25 serial: [ capabilities: removable audio cd-r cd-rw dvd configuration: status=nodisc

  Read the article

• Adding delay between damage

  - by iQue

  I have a bunch of enemies chasing my main-character, and if they intersect I want them to damage him and that's all good. The problem is that right now they damage him as long as they stand around him, every frame! and since it gets called every frame my character's HP reaches 0 almost instantly. I've tried adding delay and I've tried a timertask, but can't get it to work. This is the code I use to check for intersection: private void checkCollision(Canvas canvas) { synchronized (getHolder()) { Rect h1 = happy.getBounds(); for (int i = 0; i < enemies.size(); i++) { for (int j = 0; j < bullets.size(); j++) { Rect b1 = bullets.get(j).getBounds(); Rect e1 = enemies.get(i).getBounds(); if (b1.intersect(e1)) { enemies.get(i).damageHP(5); bullets.remove(j); } if(e1.intersect(h1)){ happy.damageHP(5); // this is the statement that needs some sort of delay, I want them to damage him every 2 seconds they intersect him. } if(enemies.get(i).getHP() <= 0){ enemies.get(i).death(canvas, enemies); score.incScore(5); break; } if(happy.getHP() <= 0){ score.incScore(-50); //end-screen } } } } } If anyone knows the logic to do this please do tell.

  Read the article

• Ubuntu 13.10, kernel 3.11 blank screen issue with hybrid graphics

  - by Lagerbaer

  On my HP Envy, which has both an Intel on-chip graphics card and an Nvidia Geforce: *-display UNCLAIMED description: 3D controller product: GK208M [GeForce GT 740M] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: cap_list configuration: latency=0 resources: memory:d2000000-d2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:5000(size=128) memory:b2000000-b207ffff *-display description: VGA compatible controller product: 4th Gen Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 06 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d3000000-d33fffff memory:c0000000-cfffffff ioport:6000(size=64) I have trouble with all newer kernels. I basically had to install 12.04 LTS and use their 3.5 kernel family to get the system to boot. The 3.8 from 12.10 or the newest 3.11 from Ubuntu 13.10 leave me with a black screen upon boot. On one occasion I did hear the "log in" sound, but the screen did not display anything. I have purged all nvidia drivers so I guess it should just use the intel drivers, but apparently this is all messed up with newer kernel versions. This is different from the other "nvidia boots into blank screen" bug in that I don't rely solely on an nvidia card. Surely the intel on-chip card should be supported and leave me with something different from a blank screen? Again, it only works with kernel versions 3.5.0-41-generic, not with the 3.11.0-12 one that ships with Ubuntu 13.10. When I go into the grub menu and change the boot options from 'quiet splash' to 'nomodeset' I am able to boot the system, but then I don't get any graphics and trying 'sudo service lightdm start' doesn't succeed (I get 100% CPU for apport, but this doesn't do anything either, so I kill it). Help, I'm all out of ideas. EDIT: Let me add that I'm using the EFI boot system and have a dual-boot installation with Windows 8.

  Read the article

• WiFi can't connect after suspend

  - by CyberOPS

  I've had this problem since Ubuntu 11.10 (my first install) but I was able to get around this issue with this answer. After I installed Ubuntu 12.04.1 I tried to use the same fix as before but I couldn't get it to work. I've also tried a couple other different fixes I found around the web but they didn't work. Basically here's what happens: I can see all the networks in my area. When I try to connect to one of them it never connects, it keeps disconnecting. After a little bit it asks for the password again but its already filled in correctly. If I hit okay it will do the exact same thing again. So does anyone know how I can get this fixed? INFO: Computer: HP Pavilion dv6t-6b00 CTO Quad Edition Entertainment Notebook PC Network Card: Intel® Centrino® Wireless-N 1000 OS: Ubuntu 12.04.1 (x64) dual booting with Windows 7 (x64) (*Not using Wubi*) Wireless Card Driver: iwlwifi UPDATE: I was about to reinstall with the DVD I made with the ISO from the official source but discovered the same issue happens on the disc's Ubuntu preview feature. I still was unable to fix it as before. I also tried the Xubuntu demo, and the same. Re installing the driver hasn't worked either.

  Read the article

• Just installed 13.10 and everything is fine except I cannot connect to the internet. Any thoughts?

  - by razorccatu

  I just installed Ubuntu 13.10 on my HP G62 laptop and the install went smoothly. I did the install off of a USB drive after trying ubuntu. While I was testing it, I connected to my Wireless with out issue and surfed a little. After the install, no wireless. I can still connect to my wireless network (at least it tells me I'm connected at full strength) but No servers can be found. I attempted to ping Google to no avail and I attempted to ping my router to no avail. I tried to then hard wire the machine and once again it told me that I was connected but I was not. When I ran dmesg, I got the following message: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolvabe. Please install nss-hostname! Is the hostname the issue? if so, how do I resolve it with out internet connection? If it's not the issue, how do I move forward? Thanks for any help. EDIT. I forgot to attach the image of my ifconfig if that might help.

  Read the article

• 2/23?????????????? x 2

  - by toshiyuki.sakuramoto

  ????1?????????2/23???????????????????2?????? 2???????????????????! ?????????????????? 1??? ??HP????????????? Oracle E-Business Suite ???????·????? ?Oracle E-Business Suite???????????TCO??? ERP??????????????(????????????)?????????????IT???IFRS?????????????????????????????? ?????????????????????????????????? ????ERP???????????????? E-Business Suite????????????????ERP??????????????????????? ???????????????????···· ???????????10??? 1/27??????? ????????????????IFRS??????????? ??????!! 2??? ??CFO??/???????? ????????????2011 ??????????????CFO????????? ???? ???CFO???????????????????????????????????????? ???????CFO??????????????? ?????????? ?? ???????????????? ????????? ?? ??CFO???????? ??? ?????????????? ????????????? ????????(CFO) ?????????????????? ?????(CFO) ??? ????????????????? ???IBM??????? ??????(CFO) ??? ???????? ??????? ????????????? ??????? ??? ?????????????????? 2??????????????????!!

  Read the article

• Join Us!! Live Webinar: Using UPK for Testing

  - by Di Seghposs

  Create Manual Test Scripts 50% Faster with Oracle User Productivity Kit  Thursday, March 29, 2012 11:00 am – 12:00 pm ET Click here to register now for this informative webinar. Oracle UPK enhances the testing phase of the implementation lifecycle by reducing test plan creation time, improving accuracy, and providing the foundation for reusable training documentation, application simulations, and end-user performance support—all critical assets to support an enterprise application implementation. With Oracle UPK: Reduce manual test plan development time - Accelerate the testing cycle by significantly reducing the time required to create the test plan. Improve test plan accuracy - Capture test steps automatically using Oracle UPK and import those steps directly to any of these testing suites eliminating many of the errors that occur when writing manual tests. Create the foundation for reusable assets - Recorded simulations can be used for other lifecycle phases of the project, such as knowledge transfer for training and support. With its integration to Oracle Application Testing Suite, IBM Rational, and HP Quality Center, Oracle UPK allows you to deploy high-quality applications quickly and effectively by providing a consistent, repeatable process for gathering requirements, planning and scheduling tests, analyzing results, and managing  issues. Join this live webinar and learn how to decrease your time to deployment and enhance your testing plans today! 

  Read the article

• Network printer problem with 12.04

  - by G. He

  I had an HP LaserJet 3030 printer connected to an Ubuntu box. It worked fine with 11.10. I was able to print from Ubuntu as well as from Windows and Mac from the home network. About a month or so ago, I upgraded 11.10 to 12.04, then things started to falling apart. My Windows 7 laptop couldn't print to the printer any more. Today, I installed many updates on 12.04, hoping that would fix the printing problem. Unfortunately, it made the situation much worse. Now not only my Windows 7 laptop won't print, my XP desktop won't print either. Every time I print something from the Windows computer, the Ubuntu box logs an error message in /var/log/samba/log.'machineName' as: _spoolss_OpenPrinterEx: Cannot open a printer handle for printer \\server. It is interesting that it uses the server name as the printer, not the \\server\xyzprinter as the printer name. Anyone had a similar problem? Anyway to work around the problem?

  Read the article

• Ubuntu 12.10 wont boot

  - by John Mark High

  im new to using Ubuntu and just bought a HP Pavilion g6-2240sa with windows 8 pre installed. I made a bootable USB with Ubuntu on it and installed alsongside windows, for 2 days it worked fine, I got into Ubuntu by doing an advanced restart from windows 8 and then booting Ubuntu from the partition it made. When i did the advanced restart today there was only 1 HDD i could select ( there were 3 before windows, a restore partition that was already there when i got the computer and Ubuntu) so i booted from the USB again and re-installed Ubuntu. then did an advanced restart and the 3 partitions where there again, i booted from Ubuntu and now heres my problem. I get the Ubuntu background when its loading then its just a black screen with some writing, its not on long enough to read, then just a black screen with a white _ and the top left corner that does nothing, i have to restat the computer and it auto boots into windows 8. im a little confused as the first time i installed Ubuntu it worked fine until the partition dissaperd), the second time i installed i did everything the same except it found the old Ubuntu so i reinstalled it and now is donst work.

  Read the article

• ubuntu 11.10 can't find wireless after waking from sleep

  - by Colleen

  I've tried a lot of proposed solutions, most of them adding files to /etc/pm/config.d, as well as WiFi stops working after waking from suspend and nothing has worked. hardware info: [colleen@colleen-HP ~]$ sudo lshw -C network [sudo] password for colleen: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:b1:ea:67 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:4000(size=256) memory:c1404000-c1404fff memory:c1400000-c1403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 8c:a9:82:99:48:8c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-21-generic-pae firmware=39.31.5.1 build 35138 ip=192.168.0.4 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:c5500000-c5501fff Is anyone else still having this problem? The two solutions I haven't tried are installing wicd and upgrading because I've heard both are kind of unstable/buggy and wicd frankly scares me.

  Read the article

• Cannot boot: FGLRX 8.780 + Kernel 2.6.35-25

  - by pluc

  The situation before this all happened is pretty standard. I have a HP Pavillion dv5 laptop with an ATI Mobility Radeon 4200 series. It always worked fine with Ubuntu for as long as I can remember. However, at one point, something happened and truly made a majestic mess of things. It might've been extra repos I enabled with Ubuntu Tweak - I do not know. But something made it so that my system would not boot any longer. And when I say "won't boot", this is what I mean: - Durning a normal bootup, any entries (except Windows) selected with GRUB (or BURG, not even sure which one I'm using anymore) will spawn the Ubuntu loading screen - then try to start X (or GDM) 5 times. The screen goes to dark, black and back to the Ubuntu loading screen. Then it just stays there until I spawn another TTY. I have no idea what is happening or why. There are no errors in my logs, and I'm truly at a loss here. I've linked three files: Xorg.0.log, the output of dmesg and the GDM log: Xorg.0.log: http://ubuntu.pastebin.com/tpVKc2tc dmesg: ubuntu.pastebin.com/Nd5aYj45 gdm's :0.log: couldn't post due to lack of points :( Let me know if any of you more knowledgeable folks can restore some sanity in my life. Any help is greatly apreciated.

  Read the article

• Will the Driver Support for Intel HD Graphics be Improved in 12.10?

  - by Hiranya

  I recently installed Ubuntu 12.04 on a HP Pavilion dv4 laptop. This is a core i7 machine with Intel HD graphics and also a separate nVidia VGA card. I had a lot of issues getting Ubuntu 12.04 working on this system. First there were issues booting up the live CD for installation. I worked around that by using the 'nomodeset' option. Then I continued to have similar issues after installation has completed. So I had to permanently add the nomodeset option to my GRUB boot configuration. At the moment I have a working installation but there are many issues: Ubuntu GUI is a bit flaky at times. The mouse pointer goes on and off when hovering over certain icons. Certain things doesn't get rendered properly on the screen. I can't access any of the tty consoles. Hitting Ctrl+Alt+F[1-6] gives me a blank screen. And once that happens I can't even come back to the UI by hitting Ctrl+Alt+F7. I've realized that tty consoles are actually working. I just can't see the text. If I enter a command like 'sudo reboot' into the empty screen the machine reboots. Can't get external displays (monitors, projectors etc) working. But I think this is probably because the VGA out is wired to the nVidia card which is not being used by Linux. colord program crashes every now and then triggering a popup message. So my main question is, will the support for Intel HD graphics be improved in the next release? Or will I have to keep using the nomodeset option in the new release too? Also I appreciate if anybody can shed some light on any of the issues listed above. Thanks in advance.

  Read the article

• Oracle Fusion Middleware 11gR1 ?FAQ??

  - by Hiroyuki Yoshino

  ??????FAQ????????????????? Oracle Technology Network (OTN)???????·??????·???????? Q. "Generic", "x86", "x86-64", ????????????????????????????????? A. ?????????????? Generic ????????·???????????????? 32????64???·??????????JDK/JVM????????? JDK/JVM???????????????????? x86 Supported System Configurations??????????????????????????????32???·???????????? x86-64 Supported System Configurations??????????????????????????????64???·???????????? ?????????? ("SPARC"??) Supported System Configurations????????????????????????????????????WebCenter for AIX?Portal, Forms, Reports and Discoverer for HP-UX PA-RISC???????? Q. SOA 11gR1 (11.1.1.1.0)??????????? 11gR1 (11.1.1.1.0)????????????????? A. ??????·????11gR1???????????????????????????????Oracle Support???????????????? Q. Oracle Fusion Middleware 11gR1???????????????????? A. Oracle Fusion Middleware 11gR1 ????????????????? Supported System Configurations?????????????? Q. Oracle Fusion Middleware 11gR1?????????????????????????????? A. Oracle Fusion Middleware?Oracle?????? Oracle Virtual Machine ????????????Oracle??????????????????????????????????????????????????? ???????? 

  Read the article

• Broadcom 4313 doesn't work following 12.04 upgrade

  - by Lucas

  I have an hp G62-228Ca laptop with a BCM4313 previously running Ubuntu 11.10. I ran the 12.04 upgrade last night without much thought. Following the upgrade and mandatory reboot, the wireless card no longer shows up in the network manager, the first time I've had any kind of issues with wireless under Ubuntu. I've done much Googling on the issue but so far I haven't found a permanent solution. Mucking around with some packages though (I've installed five different ones or so), I've managed to devise a workaround that I must run every time I boot the laptop. I have to remove the Broadcom STA driver and reinstall it. Inspiration taken from here: WiFi does not work, Broadcom STA Wireless driver does not work on a BCM4313 After the second modprobe command, the wireless reappears in the network manager and ten seconds after that I'm back on the wifi. If anyone can provide some advice on how to fix this permanently I will be extremely grateful. I'd rather not roll back to 11.10 or reinstall, but I will if I need to. Just let me know if you need the output from any terminal commands. Thanks in advance!

  Read the article

• Crackling sound from microphone recently, in 13.04

  - by Patrig Droumaguet

  I use 13.04 since the release and I use Skype which was working well. But recently I've had remarks saying my voice was "crackling", even if the voice from my interlocutor was perfect. Making a test with Audacity and Cheese, I've seen that every recorded sound (with the front microphone of my laptop or a jack microphone) was crackling. It's not really like saturating, the sound has a lot of annoying pops. I've tried to check the settings, they were still on PulseAudio. I've even tried the extreme solution : re-installing Ubuntu (because initially it was working)… with the same problem. If I boot on Windows (dual-boot) I have no problem (so it's not physical). If anyone could help :) My laptop is a HP dv6-6165sf. The sound card is a "IDT 92HD81B1X5" (with BeatsAudio). Thanks a lot ! New tests - july 6th Hi again, I've tried editing /etc/pulse/default.pa with these three settings : load-module module-udev-detect use_ucm=0 tsched=0 load-module module-udev-detect tsched=0 load-module module-udev-detect use_ucm=0 The three of them don't change anything, except the last one (which was by default) which makes Audacity record without any crackling sound. But in Skype, Cheese and Kazam, the sound is crackling… I've installed again Ubuntu 13.04 (from scratch, deleting everything from /home), and I've updated it. The microphone is still cracking. Thanks for your help !

  Read the article

• ubuntu 12.04 installer does not recognize drive partitions

  - by endless forms

  I recently purchased a new HP Pavilion HPE desktop running Windows 7. I am trying to install a dual-boot system with 12.04. However, when I run the LiveCD I only get as far as the "Install" window where you can select the partitions for your drives. On the bottom where it says "device for boot loader installation" I have "/dev/sda" and cannot select any other devices. All the options to change the drives are greyed out, most likely because there are no drives in the window. I partitioned my largest drive using the tools within Windows, then booted into the CD, but nothing shows up. I then used Gparted to change the new space from unallocated to an /ext2, and still nothing shows up. The installer does not recognize anything, but when I go into an Ubuntu session and use the disk utility manager I can see the partitions I made. Anything I do has to be done outside of the installer. I have no files on this new computer, so this is the perfect time to install a parallel OS. I would like avoid completely reinstalling Windows, however. I've been over the forums many times, but all the answers I've found have not worked for me. I also tried flagging the new, empty partition as boot, but that screwed Windows up. Also, the WUBI installer hits the same point and quits. I know that the disk itself is fine because I just made another dual boot system on a Gateway PC. This makes me think something within this computer is preventing the installer from "seeing" the drives. Any help would be much appreciated! Edit in response: The main part of the partitioning window shows no partitions, everything is blank. There is no way to add partitions, and all the buttons are useless. I've tried defragging my drive multiple times, and I also used the same disk to dual-boot another PC with no problems, so it's not the disk, it's definitely the computer.

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >