Search Results

Search found 12497 results on 500 pages for 'linked servers'.

Page 84/500 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• Intermittent wired network issues in 14.04

  - by Tommy Brunn

  Since yesterday, my wired network connection has been dropping for a couple of seconds every 30 seconds or so. To my knowledge, I had not made any changes to my network. Output of ifconfig -a: ? ~ ifconfig -a eth0 Link encap:Ethernet HWaddr 6c:f0:49:b9:b1:7f inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:feb9:b17f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11597 errors:0 dropped:0 overruns:0 frame:0 TX packets:9783 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10101682 (10.1 MB) TX bytes:1215142 (1.2 MB) Interrupt:48 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:96691 errors:0 dropped:0 overruns:0 frame:0 TX packets:96691 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13594355 (13.5 MB) TX bytes:13594355 (13.5 MB) lspci |grep Ethernet: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) Pinging my router: ? ~ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.435 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.571 ms ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable 64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=1.03 ms And the output of route: ? ~ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 1 0 0 eth0 Some messages from /var/logs/syslog: ? ~ tail -f /var/log/syslog Jun 6 10:37:34 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:34 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:37 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:37 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:39 lolbox dhclient: XMT: Solicit on eth0, interval 8660ms. Jun 6 10:37:39 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:39 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:47 lolbox dhclient: XMT: Solicit on eth0, interval 16820ms. Jun 6 10:37:47 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:47 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:04 lolbox dhclient: XMT: Solicit on eth0, interval 34410ms. Jun 6 10:38:04 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:04 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13045 Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:37:34 lolbox whoopsie[1133]: online Jun 6 10:38:16 lolbox whoopsie[1133]: offline Jun 6 10:38:16 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:38:16 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13044 Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:38:16 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:17 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:17 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:17 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:18 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13160 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13161 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:38:18 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:18 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:18 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:18 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:18 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:18 lolbox dhclient: All rights reserved. Jun 6 10:38:18 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:18 lolbox dhclient: Jun 6 10:38:19 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:19 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:19 lolbox dhclient: All rights reserved. Jun 6 10:38:19 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:19 lolbox dhclient: Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:38:19 lolbox dhclient: Bound to *:546 Jun 6 10:38:19 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:38:19 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv6 state changed nbi -> preinit6 Jun 6 10:38:19 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on Socket/fallback Jun 6 10:38:19 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3fc9376d) Jun 6 10:38:19 lolbox dhclient: XMT: Solicit on eth0, interval 1020ms. Jun 6 10:38:19 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:19 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:38:20 lolbox dhclient: bound to 192.168.0.16 -- renewal in 41481 seconds. Jun 6 10:38:20 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:38:20 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:38:20 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:38:20 lolbox dhclient: XMT: Solicit on eth0, interval 2110ms. Jun 6 10:38:20 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:20 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:38:21 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:38:21 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:38:21 lolbox whoopsie[1133]: online Jun 6 10:38:21 lolbox ntpdate[13217]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:38:21 lolbox ntpdate[13217]: no servers can be used, exiting Jun 6 10:38:22 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:38:22 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:38:22 lolbox dhclient: XMT: Solicit on eth0, interval 4080ms. Jun 6 10:38:22 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:22 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:26 lolbox dhclient: XMT: Solicit on eth0, interval 8450ms. Jun 6 10:38:26 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:26 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:35 lolbox dhclient: XMT: Solicit on eth0, interval 16630ms. Jun 6 10:38:35 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:35 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:51 lolbox dhclient: XMT: Solicit on eth0, interval 34860ms. Jun 6 10:38:51 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:51 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:58 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:38:58 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13161 Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:22 lolbox whoopsie[1133]: online Jun 6 10:39:04 lolbox whoopsie[1133]: offline Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:39:04 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:39:04 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13160 Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:39:04 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:05 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:05 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:05 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:06 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13270 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13271 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:39:07 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:07 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:07 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:07 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:07 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:07 lolbox dhclient: All rights reserved. Jun 6 10:39:07 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:07 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:08 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:08 lolbox dhclient: All rights reserved. Jun 6 10:39:08 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:08 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Bound to *:546 Jun 6 10:39:08 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:39:08 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:39:08 lolbox kernel: [ 1446.098590] type=1400 audit(1402043948.002:75): apparmor="DENIED" operation="signal" profile="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=13273 comm="nm-dhcp-client." requested_mask="send" denied_mask="send" signal=term peer="/sbin/dhclient" Jun 6 10:39:08 lolbox kernel: [ 1446.098599] type=1400 audit(1402043948.002:76): apparmor="DENIED" operation="signal" profile="/sbin/dhclient" pid=13273 comm="nm-dhcp-client." requested_mask="receive" denied_mask="receive" signal=term peer="/usr/lib/NetworkManager/nm-dhcp-client.action" Jun 6 10:39:08 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:39:08 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on Socket/fallback Jun 6 10:39:08 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3e0183b9) Jun 6 10:39:08 lolbox dhclient: XMT: Solicit on eth0, interval 1050ms. Jun 6 10:39:08 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:39:08 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:39:09 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:39:09 lolbox dhclient: bound to 192.168.0.16 -- renewal in 35498 seconds. Jun 6 10:39:09 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:39:09 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:39:09 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:10 lolbox dhclient: XMT: Solicit on eth0, interval 2180ms. Jun 6 10:39:10 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:10 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:39:10 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:39:10 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:39:10 lolbox whoopsie[1133]: online Jun 6 10:39:10 lolbox ntpdate[13339]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:39:10 lolbox ntpdate[13339]: no servers can be used, exiting Jun 6 10:39:11 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:39:11 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:39:12 lolbox dhclient: XMT: Solicit on eth0, interval 4350ms. Jun 6 10:39:12 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:12 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:16 lolbox dhclient: XMT: Solicit on eth0, interval 8740ms. Jun 6 10:39:16 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:16 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:17 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:17 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:25 lolbox dhclient: XMT: Solicit on eth0, interval 17610ms. Jun 6 10:39:25 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:25 lolbox dhclient: IA_NA status code NoAddrsAvail.

  Read the article

• Proxmox VE cluster not working

  - by JJ56

  I have been using a Proxmox VE 2.0 cluster (2 servers) for months. Today, I had the "bright idea" to install a GUI on one of the servers. I used tasksel, and selected the graphical desktop environment (Gnome). When I rebooted the server, neither of the servers on the cluster could see each other (shows a red light by the server on the sidebar, no statistics). The VMs on each server are working fine, individually. pvecm status on the broken server shows cman_tool: cannot open connection to cman, is it running ?. Running it on the other server outputs a lot of lines (here: http://pastebin.com/HpQfUHTU), but I assume the important bit is expected votes:2 total votes: 1 Trying pvecm delnode (othernode) on either server outputs: cluster not ready - no quorum? Any suggestions as to how I can fix this? Thanks in advance!

  Read the article

• heartbeat: Bad nodename in /etc/ha.d//haresources [node1]

  - by Richard

  I'm trying to start heartbeat on Ubuntu 10.04 with service heartbeat start, but getting the following errors: heartbeat[24829]: 2011/11/22_19:31:07 ERROR: Bad nodename in /etc/ha.d//haresources [node1] heartbeat[24829]: 2011/11/22_19:31:07 ERROR: Configuration error, heartbeat not started. On on server uname -n produces loadb1, on the second server uname -n produces loadb2. The two servers can ping each other okay with those names. This is /etc/ha.d/ha.cnf on both servers: debugfile /var/log/ha-debug logfile /var/log/ha-log logfacility local0 keepalive 2 deadtime 10 udpport 694 bcast eth1 ucast eth0 my.external.ip ucast eth0 my.external.ip ucast eth1 10.0.0.5 ucast eth1 10.0.0.6 #udp eth0 node loadb1 node loadb2 auto_failback off And this is /etc/ha.d/haresources on both servers: node1 IPaddr::46.20.121.113 httpd smb dhcpd Authkeys is also set up. What am I doing wrong? The part where I'm least clear is the ucast/bcast lines.

  Read the article

• Windows 2008 R2 DHCP server not responding to DHCP discover

  - by MartinSteel

  I've got two Windows 2008 Enterprise R2 servers both running DNS and DHCP called cod & lobster. DHCP is setup using the split scope option introduced with 2008 R2, whereby both servers should respond with the first response providing the lease. Setup is as follows: Cod - IP: 192.168.0.231 - Pool: 192.168.0.101 - 192.168.0.179, exclusion for 160-179. - Response Delay: 0ms - Authorised in Active Directory (Re-authorised to confirm) - Windows firewall disabled while testing Lobster - IP: 192.168.0.232 - Pool: 192.168.0.101 - 192.168.0.179, exclusion for 101-159. - Response Delay: 1000ms - Authorised in Active Directory All DHCP leases to clients are currently being issues by Lobster rather than Cod. Packet captures with Wireshark show the following (all to broadcast address): Client - DHCP Discover Lobster - DHCP Offer (after 1s delay) Client - DHCP Request Lobster - DHCP Ack Client - DHCP Inform From my setup with two servers I'd expect to see a DHCP Offer coming from Cod almost immediately after the DHCP Discover. Does anybody have any idea what would prevent the DHCP Server responding to the discover?

  Read the article

• Windows Server 2012 IPAM feature - "Unblock IPAM Access" error/recomended action

  - by HopelessN00b

  So, I'm in the process of setting up an IP Address Management server, using the built-in IPAM feature in Server 2012, and have run into a problem that I'm hoping someone else has successfully solved. Following the technet guide here, I've installed and configured IPAM, and have provisioned it via GPO. After verifying that the PowerShell invoke-ipamgpoprovisioning command is successful, managing the desired servers in IPAM, running gpupdate /force on the servers and refreshing my view in IPAM, I'm still getting the less-than-useful recommended action of "Unblock IPAM Access" for all servers. (First done 3 hours ago, so it's not a give-it-time-to-propagate issue.) Can't, for the life of me, seem to figure out what's causing this, find anything useful in the logs, or find much about this on Google or in the help files, so I was wondering if anyone here had any ideas about how to fix this, or even where to start looking. I'd really like to get this working, because if not, I have to resume work on creating an Excel spreadsheet for IP address management.

  Read the article

• IIS 7.0: Requiring Client Certificates causes error 500 and "page cannot be displayed"

  - by user48443

  I have two Windows 2008 x86 servers running IIS 7.0, one site on each server; both sites are SSL-enabled, using DoD-issued certificates. Both sites are accessible via https over port 443, but fail the moment Client Certificates are set to Require or Accept. IIS log records error 500.0.64 but nothing else. I have several Windows 2008 IIS 7 x64 servers that require client certificates and they are working as expected; it's just the two x86 servers that are being problematic.

  Read the article

• Recommended SpamAssassin update channels?

  - by Timo Geusch

  I'm currently using SpamAssassin on a couple of mail servers that I look after. SpamAssassin runs in the context of amavisd-new on those servers and with the usual bunch of plugins (FuzzyOCR, DCC, pyzor, razor). Currently the servers are getting their rule updates from the default SpamAssassin update channel (updates.spamassassin.org). Overall the setup seems to be reasonably effective but some types of spam seem to wander right through it even though I've made repeated attempts at training spamassassin. My guesstimate is that about 85%-90% of the spam that gets through policyd-weight makes it through the filters and it's been getting a lot worse recently as spammers are getting better at working their way through filters. Can someone recommend additional sources of filters to make SpamAssassin more effective? So far I've found OpenProtect's update channel but are there others worth looking at?

  Read the article

• Setting WMI permissions remotely

  - by christianlinnell

  I've developed a tool that does a simple retrieval of registered services and installed applications from remote Windows Server 2003 servers via WMI. My problem is, the tool needs to be run on an ad hoc basis by a user who is not an administrator of those servers. I've created a domain user (which the tool will use to run the query) that I'd like to grant remote WMI permission on each server, but given there are about 200 servers, I can't do it manually. Is there a way to grant access to that domain user via WMI, or by distributing a registry change via SMS or Group Policy?

  Read the article

• Justifying a memory upgrade

  - by AngryHacker

  My employer has over a thousand servers (running SQL Server 2005 x64 and a couple of other apps) all across the country. And in my opinion they are all massively underpowered for what they need to do. Specifically, I feel that the servers simply do not have enough RAM for the amount of volume the machines are asked to do. All the servers currently have 6GB of RAM. The users are pretty much always complaining about performance (mostly because, immo, the server dips into the paging file quite often). I finally convinced the powers that be to at least try out a memory upgrade on one box and see the results. However, they want before and after metrics, so that they can see that the expense will be justified. My question is what metrics should I collect to see whether the performance truly improves on the box? I am a dev, so I am not sure how and what to collect (i have a passing knowledge of Perfmon).

  Read the article

• OpenVPN make redirect-gateway optional

  - by Tuinslak

  Hi there, I'm currently running an OpenVPN server for multiple clients. All traffic is directed through the VPN (it's set up as gateway; push "redirect-gateway def1"). So far, all is working fine. However, I'd like to connect a couple of servers to this virtual private network, without these servers using the OVPN daemon as gateway. These servers have to be accessible from both their WAN as well as their LAN IP address. Certain services will be accessible only from the LAN side. Is there any way, for a client, to ignore the push redirect-gateway option? Kind regards, Tuinslak

  Read the article

• DFS share Access denied for some time after workstation is booted.

  - by Jonathan

  I have 2 Win server 2008 servers acting as domain controllers and Dns servers doing DFS. All my workstations are windows xp sp3. I have a DFS share drive mapped at login via login script. After the pc is booted I get an access denied message when trying to access the mapped drive. If i go to the file share on one of the servers i can get to it fine. After about 10 minutes i can try to access the mapped drive again and it works fine. I am not sure if it is some delay happening in dfs name resolution or a gpo issue.

  Read the article

• Using dnsmasq dns server on a laptop for a locally hosted tld

  - by kimausloos

  Hi, I'm running a working apache install with mod vhost_alias on a laptop. Everything works, but I have to manually add hosts in my /etc/hosts file. I'd like to install dnsmasq to point a tld to my local machine (this is not the problem, I know how to add a wildcard tld to dnsmasq), but how do I make it so that it will go look for other dns servers upstream? Remember I'm talking about a laptop, so I will be working on various wifi hotspots, with different default gateways, dns servers, etc. I've searched for quite some time but the only things I find are guides that require you to hardcode the upstream servers wich is a no-go for me. Any help is appreciated!

  Read the article

• HAProxy -- pause/queue all traffic without losing requests

  - by Marc

  I basically have the same problem as mentioned in this thread -- I would like to temporarily suspend all requests to all servers of a certain backend, so that I can upgrade the backend and the database it uses. Since this is a live system, I would like to queue up requests, and send them to the backend servers once they've been upgraded. Since I'm doing a database upgrade with the code change, I have to upgrade all backend servers simultaneously, so I can't just bring one down at a time. I tried using the tcp-request options combined with removing the static healthcheck file as mentioned in that thread, but had no luck. Setting the default "maxconn" value to 0 seems to pause and queue connections as desired, but then there seems to be no way to increase the value back to a positive number without restarting HAProxy, which kills all requests that had been queued up until that point. (The "hot-reconfiguration" options using -sf and -st start a new process, which doesn't seem to do what I want). Is what I'm trying to do possible?

  Read the article

• Automatically Login & Startup A Windows Program On Amazon's EC2 Service

  - by darkAsPitch

  How can I automatically start a program on Amazon's EC2 Windows 2008 web servers? For example, if I wanted to test the "Digg effect" on a web page of mine, how could I open 100 windows 2008 servers at once, each loading one (or two?) instances of the firefox web browser? I have placed a sample batch file in the windows startup folder that echos the time it was called, but it is only started when I actually login remotely via the remote desktop protocol. I don't want to have to login to 100 servers to get my software to run :P What can I do? I am using this Windows 2008 Datacenter, Amazon-supplied AMI specifically: ami-a2698bcb

  Read the article

• Ubuntu web server cluster checks Ubuntu repository for script updates with cron

  - by StuartTheY

  I have a cluster of Ubuntu 12.04 web servers running a lamp stack. All of these servers are connected to a Load Balancer on Amazon Web Services. What I want to be able to do is have a dedicated Ubuntu server that I can update the PHP files on and have the other web servers check with cron to get the updates files from the repository. They don't have to use cron but that was the only thing I could think of, unless there was a way to have the updated repository tell them that it has updated files. And then how to transfer those files. Also if there is a ways for a server to check for updated files when it boots because I am going to be using auto scaling on AWS so when there is an increase in the load and another server gets created I need it to download the updated files from the repository when launched. Not sure how to transfer files from server to server.

  Read the article

• Rackspace copy script failure message "java.net.SocketTimeoutException: Read timed out"

  - by user53864

  I am using Rackspace for Ubuntu cloud server. Everyday a script(I guess the script is from rackspace) executes on the cloud servers which copies the backfile to the Rackspace CloudFiles and sends the mail as if the files are copied and I've scheduled the script on the cloud servers. I've no much knowledge of the script and I guess the script is based on Cruise(as I could see build.xml, some jar files ...). Everyday the files are copied to the Rackspace from cloud servers but sometimes don't know why, the files will be copied to Rackspace sending an error failure message or sometimes the files will not be copied and sends the error failure message like the one below. Error while backing up on Station1 on 03/03/2011 04:50 AM and reason for error is java.net.SocketTimeoutException: Read timed out Anybody using Rackspace?, anybody has any fix for this?

  Read the article

• Resolving DNS queries for two disconnected, private, networks

  - by Mikeage

  I'm trying to setup two PCs (one Windows, one Linux, but my understanding is that this problem is more DNS and less OS) as follows: Home network: 192.168.1.0/24 VPN (via OpenVPN server not within the home network): 192.168.2.0/24 . I would like a PC on both networks to be able to access three different types of site: Internet addresses Addresses on the home network Addresses on the vpn However, I'm not sure how/which DNS servers to use. If I prioritize my home DNS server, I can resolve (1) and (2), but not (3). If I prioritize my VPN DNS server, I can't resolve addresses of type (2). Of course, looking up addresses via nslookup and explicitly setting the correct server works, so I know my local DNS servers are OK. Is there any way I can set up my PCs to fallback on the second DNS server if there is no response? Alternatively, is there any way I can tell different queries to go to different servers [maybe by setting up different subdomains; foo.local.something vs. bar.vpn.something]? Thanks

  Read the article

• Load-balancer options

  - by toolkit

  I am looking at a number of possible options for load-balancing. So far, I am constrained to the following options: DNS server load-balancer, balancing to a cluster of tomcat servers, with terracotta for session replication. Pros - don't have to buy new kit. Cons - DNS lb can keep directing to a broken server. Hardware load-balancer, direct to cluster of tomcat servers. Pros - could have second box for failover lb. Cons - expense. Apache server load-balancer. Pros - apache's lb polls for broken servers. Cons - apache server is single point of failure, plus need to buy another server. Are there any other options I should consider? Thanks. Update: Thanks for all the answers so far +1's all round. Not accepting an answer yet, to keep more ideas coming.

  Read the article

• Do i need a dedicated server for load balancing?

  - by Ben

  I'm completely new to the concept of load balancing so i hope this question isn't a "stupid question" because i've been searching around and im having a hard time understanding this. So to my understanding, in order to load balance, i need a separate machine with an ip address i can direct all traffic to. I initially thought i needed to rent 3 dedicated servers, one for load balancing and the other two as backend servers. Would a dedicated server be too much for a load balancer or do hosting companies have special types of computers for that process? Then i read somewhere else that i can install a load balance software in both of the two servers and configure it in a way that doesn't require me to rent another machine/dedicated server for load balancing. So im a bit confuse on how to actually implement a load balancer and whether or not i need a dedicated server for the sole purpose of acting as a load balancing machine. Also, i was recommended to use HAproxy so i'll be heading that direction for load balancing.

  Read the article

• No "Terminal Services" branch in "Group Policy Object Editor"

  - by ayavilevich

  Hi, We have several identical several servers in a hosting company. They run Windows 2003 R2 Std SP2 64bit. The servers are not in a domain. We have recently received a new server with the same configuration and hardware. However, the new server is different in some way. When we run "gpedit.msc /s" there are much less options in the tree than the other servers. Specifically we are missing the configuration of "Terminal Services". Many other items are missing under "Administrative templates" and "Windows components". Screenshot of correct server: (can't post link due to SF policy) Screenshot of new server: http://img686.imageshack.us/img686/572/gpowindowscomponentstp5.png What should we try? Thanks, Arik.

  Read the article

• Pfsense: Inbound Load Balancing https with sticky connection

  - by Zeux

  first of all I'm very sorry for my English... This is my scenario: Internet Firewall+LB: pfsense_1(Active) + pfsense_2(Passive) in CARP Pool servers: 3 x nginx(PHP5+HTTP+HTTPS) Pfsense 1 and 2 CARP configured with Virtual IP (pubblic). Nginx servers's ips are all private. I want to load balance inbound HTTP and HTTPS connections between the 3 nginx web servers. An importat thing is that the HTTPS connections must be "sticky connections": in HTTPS connections, after login by username and password, I setup a php session and therefore when a client starts a HTTPS connection it will be always redirected to the same nginx server, until it disconnects itself, it closes the page/browser or after a timeout (30minutes?) without activity. Is this possible whit the last release(2.0.1) of pfsense? thank you very much...

  Read the article

• HP DL160 vs DL360 for virtualization

  - by Chris

  Hi, We're planning to consolidate our infrastructure (a dozen servers). We'll buy two or three identical new servers who will be setup as a XenServer pool. Load balancing and HA tools will monitor the pool and vMotion VMs in case of failure/overload. I know that the DL100 series of HP servers is cheaper than the DL300 serie (in every sense of the word). As we don't need local storage (we have a SAN) and can live with a temporary down server (provided that Xen Server HA tools work as advertized), what are the downsides going with the DL100 serie ? Thanks, Chris

  Read the article

• HD Video Capture Card w/ Good API?

  - by Sheep Slapper

  Does anyone here know of a good HD video capture card that has a good (comprehensive) API? I administer a few servers that do some video encoding right now, but when we make the switch to HD cameras, they won't be sufficient. In addition to this, the servers we have now are black boxes, closed to me except to start/stop the video capture device. I'd like to be able to roll my own, so we can better integrate it with our existing systems, but I know almost nothing about what kind of HD capture cards are out there, and if I can avoid spending money just to test their APIs that would rock. So does anyone have any experience with this? All our other software is in C#, and I'd like to set up the new servers with web interfaces to start/stop the capture (also in C#, using .NET 3.5 probably). I'm not sure how language specific these APIs would be, but that's what I'm working with just as a reference point. I appreciate any help the community can give!

  Read the article

• Implementing a Linux-HA based clustering setup on Windows

  - by Alex

  I have a (tried and tested) setup involving: 2x Load balancing nodes on a floating IP via Heartbeat, load balancing 2 tomcat servers. 2x Tomcat servers 2x Galera Cluster MySQL servers synchronously replicating (+1 arbitrator node) All are evenly spread across 2 physical nodes. Now, I have to somehow get the same functionality on Windows Server (2008? I think) nodes .... running under Xen virtualization. There is no possibility to use Linux for any of the nodes. I count two main problems: No Linux-HA hearbeat daemon for the load balancing No Galera synchronous replication for MySQL I freely admit to having nearly no Windows knowledge when it comes to clustering. Is there a way to closely mimic the setup I have described or is it a total write-off?

  Read the article

• Memcached server: Is it a good practice to point two server urls to the same server?

  - by Niro

  I have a system where there are connections to a memcache server from several different files and servers. I would like to stay with one server but keep the option of increasing the number of memcache servers (for periods of of high traffic). My idea is to tell memcache there are two servers, while the two urls will point (by DNS) to a single server. In the future if I want I can add a server and change DNS without changing the code in many places. Is this a good practice? Is there a performance cost to the fact that there are two server connections but they both point to the same server? Any other idea how to achive instant expeandability of memcache capacity without need to change the code and deploy ?

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >