Search Results

Search found 2840 results on 114 pages for 'ports'.

Page 84/114 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• wrt54gl reboots; troubleshooting steps?

  - by Bill

  I am using about 10 wrt54gl's in a small school. I am using a combination of stock firmware and Tomato 1.25, slowly moving towards all Tomato. We have had these devices installed for several years without problems. Recently, more and more of the units have started to spontaneously reboot, usually during high-traffic times (but not always). For the most part, the rebooting is not critical for us, but the wrt54gl's temporarily revert to 192.168.1.1 on the LAN ethernet ports and conflict with a critical server that's already installed with that IP. (Yes -- we plan to move the server off that address, but it is an involved process.) Both Tomato and the stock firmware (several versions from recent to several years old) exhibit the same problem: random reboots and reverting to 192.168.1.1 and conflicting temporarily with our server until the firmware boot process finishes. Here are my questions: Any way to prevent the wrt54gl's from reverting to 192.168.1.1 during the boot process? I was thinking of doing a custom firmware mod, although I hate to go that direction. Any steps to take in troubleshooting the reboots? Only some of the wrt54gl's reboot, which is odd. Others stay online for weeks and months without issues. Thanks.

  Read the article

• Unable to connect remotely to Vsftpd server set up on CentOS VirtualBox

  - by ryekayo

  I have set up a Vsftp server using the following instructions provided Here and even went as far as following the commentary at the bottom. But I am unable to connect remotely. When I attempt to use FileZilla or my Ubuntu terminal, I always get: ryan@ryan-Galago-UltraPro:~$ ftp 10.0.x.xx ftp: connect: Connection timed out ftp> I have checked and re-checked iptables conf file and made sure that Port 21 is being Accepted and it is. I have looked this up on the web and decided to try nmap to port scan it and this is what I get for a result: ryan@ryan-Galago-UltraPro:~$ nmap -PN 10.0.xx.xx Starting Nmap 6.40 ( http://nmap.org ) at 2014-08-19 15:01 EDT Nmap scan report for 10.0.xx.xx Host is up. All 1000 scanned ports on 10.0.xx.xx are filtered Nmap done: 1 IP address (1 host up) scanned in 201.38 seconds Is there anything else that I should do or check for? UPDATE: I have tried to ping from the virtual machine to my IP address on Ubuntu and have been successfully able to. I cannot ping to my virtual machine from Ubuntu. I have narrowed this down to possibly being a firewall related issue on Ubuntu's side, but why would I be unable to connect from FileZilla?

  Read the article

• ProCurve network expansion

  - by Blue Warrior NFB

  I've hit a bit of a wall with our network scale-out. As it stands right now: We have five ProCurve 2910al switches connected as above, but with 10GbE connections (two CX4, two fiber). This fully populates the central switch above, there will be no more 10GbE Ethernet connections from that device. This group of switches is not stacked (no stack directive). Sometime in the next two or three months I'll need to add a sixth, and I'm not sure how deep of a hole I'm in. Ideally I'd replace the core switch with something more capable and has more 10GbE ports. However, that's a major outage and that requires special scheduling. The two edge switches connected via fiber have dual-port 10GbE cards in them, so I could physically put another switch on the far end of one of those. I don't know how much of a good or bad idea that would be though. Is that too many segments between end-points? Some config-excerpts: Running configuration: ; J9147A Configuration Editor; Created on release #W.14.49 hostname "REDACTED-SW01" time timezone 120 module 1 type J9147A module 2 type J9008A module 3 type J9149A no stack trunk B1 Trk3 Trunk trunk B2 Trk4 Trunk trunk A1 Trk11 Trunk trunk A2 Trk12 Trunk vlan 15 name "VM-MGMT" untagged Trk2,Trk5,Trk7 ip helper-address 10.1.10.4 ip address 10.1.11.1 255.255.255.0 tagged 37-40,Trk3-Trk4,Trk11-Trk12 jumbo ip proxy-arp exit

  Read the article

• iptables configuration to work with apache2 mod_proxy

  - by swdalex

  Hello! I have iptables config like this: iptables -F INPUT iptables -F OUTPUT iptables -F FORWARD iptables -P INPUT DROP iptables -P OUTPUT DROP iptables -P FORWARD DROP iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --sport 80 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A OUTPUT -p tcp --sport 443 -j ACCEPT Also, I have apache virtual host: <VirtualHost *:80> ServerName wiki.myite.com <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8901/ ProxyPassReverse / http://localhost:8901/ <Location /> Order allow,deny Allow from all </Location> </VirtualHost> My primary domain www.mysite.com is working well with this configuration (I don't use proxy redirect on it). But my virtual host wiki.mysite.com is not responding. Please, help me to setup iptables config to allow wiki.mysite.com working too. I think, I need to setup iptables FORWARDING options, but I don't know how. update: I have 1 server with 1 IP. On server I have apache2.2 on 80 port. Also I have tomcat6 on 8901 port. In apache I setup to forwarding domain wiki.mysite.com to tomcat (mysite.com:8901). I want to secure my server by disabling all ports, except 80, 22 and 443.

  Read the article

• Cannot establish a network connect to VMWare Fusion VM

  - by twolfe18

  I am running Snow Leopard 10.6.2 (not the server edition) with VMWare Fusion 3.0.0 and I trying to get my Ubuntu 9.10 x86_64 VM working. I am using a bridged connection, and I have an internet connection FROM the Ubuntu VM (I can download updates, ping websites, etc), but I cannot connect TO the Ubuntu box from any other device on my network. I am trying to get Mongrel up on the Ubuntu VM for some Rails stuff, but it's not working. I know Mongrel/Rails is not the problem because if I start the server on the Ubuntu VM, background the process, and then wget the index page, it works. I just cannot connect to the site from another IP. I have tried using a static IP and a DHCP IP configuration on the Ubuntu VM, neither work (for incoming connections, both work for outwards). I have port scanned the Ubuntu VM, and it appears that all ports are closed. However, the Ubuntu VM does respond to pings. I noticed a similar question here: http://serverfault.com/questions/99757/setting-up-a-bridged-network-with-vmware-fusion, but no answer. Any ideas?

  Read the article

• Intel DriverInstall issue on HP ProLiant server DL580G5

  - by TomTom

  Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

  Read the article

• How to wire 20 computers and 20 phones and 1 server into LAN?

  - by John Smith

  I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

  Read the article

• Monitor connected with WiDi just shows a black screen

  - by Pops

  I have a Dell XPS 18 and want to use an external monitor with it. The monitor has VGA and DVI-D inputs. The XPS 18 has no video output ports, but it does support Intel WiDi. I have a Netgear P2TV2000 WiDi receiver, but it only has composite and HDMI outputs. I'm connecting the receiver to the monitor with an HDMI cable and an HDMI/DVI-D adapter. So, in short, the video path is: Computer → WiDi → WiDi receiver → HDMI cable → HDMI/DVI-D adapter → Monitor After setting all this up, I can't get anything to display on the monitor. At the moment I power the monitor on, I can see my desktop for a brief fraction of a second, and then everything goes black. All of the relevant drivers have been updated to the latest versions. When I use a different WiDi-enabled computer to connect to the same monitor, everything works fine. When I use the original computer and receiver to connect to a TV, everything works fine. It's only when I connect the original computer to the monitor I want to use that the connection fails. What could be going wrong here, and how can I get the video to work consistently?

  Read the article

• can't access SATA card config screen on boot, nor access the disks

  - by Ronald

  We've just upgraded our file server using an ASUS P6T WS Pro board, running FreeBSD-RELEASE 8.2 and using zfs to manage 12 WD20EARS disks. Since our 3ware card has been giving us trouble we started using the six on-board SATA connectors and got a SuperMicro USAS2-L8i to provide eight more ports. Mechanically, the card is an awkward fit but electrically it all seems ok. Upon boot, the LSI controller shows up and states that pressing ctrl-c will bring up the LSI Config Utility. When doing that, the message changes to state that the utility will be started after initialization, however that never happens. There does seem to be an error message that's only displayed too briefly to read and seems to be about PCI and "not enough space". (That message is pushed off by a hardware summary and I've found no way to scroll back at this point.) The disks do not show up in any recognizable ways after booting, either. I found a hint in another discussion to check the address mapping on either the card or the motherboard BIOS, but have found no way to do that. So what I tried on a hunch is to disable everything that's on-board, including network adapters, Firewire controller and SATA. In fact, after doing that, I can successfully launch the LSI Config Utility. As far as I can tell, all looks well in there, and when booting in that configuration it also displays a list of the disks connected to it, which looks just fine as well. Only problem now is that I can't boot that way, because I need the on-board SATA controller and network adapters. As soon as I re-enable any of them I'm back to square one. That discussion I mentioned about mapping addresses said to try D000, then D7FF, then DFFF, in order. The LSI Config Utility shows the card address as D000 but offers no way of changing it. Any tips or insights would be appreciated.

  Read the article

• Configure J2EE Agent with OpenAM behind Reverse Proxy

  - by Troy

  I have a reverse proxy with two SSL enabled NamedVirtualHosts on different ports. Both containers on each internal host is GF 2.1.1. Proxy configuration as follows: Proxy URL -> Internal URL https://apps.mydomain.com -> http://apps.internal.com https://secure.otherdomain.com:8080/ -> http://secure.internal.com I initially tried configuring the J2EE agent in OpenAM and the web app container to use the internal URLs (I appended /openam and /agentapp respectively). However, I received the following errors when trying to access a secured application such as https://apps.mydomain.com/webapp. java.lang.RuntimeException: Failed to load configuration: ApplicationSSOTokenProvider.getApplicationSSOToken(): Unable to get Application SSO Token A second attempt gives the following error: java.lang.NoClassDefFoundError: Could not initialize class com.sun.identity.agents.filter.AmFilterManager Along with these in the agent debug.out: ERROR: Failed to obtain auth service url from server: null://null:null ... SiteMonitor: Site URL http://secure.internal.com/openam/namingservice is not available. If I specify the server and agent urls using the proxy urls, then the agent appears to be working and I am redirected to the OpenAM login page. However, the goto in the URL is http://apps.mydomain.com/webapp instead of https://apps.mydomain.com/webapp (missing https). So after authentication, the redirect fails. Now I could possibly get by with mod_rewrite, but it feels hackish and I really want to know what's going on. Any ideas?

  Read the article

• ssh keys rejected each day

  - by EddyR

  I've had OpenSSH server running on my debian server for a couple weeks and all of a sudden now when I go to login the next day it rejects my ssh key and I have to manually add a new one each time. Not only that but I have the "tunneling with clear-text passwords" option enabled and the non-root (login with root is disabled) account for that is rejected too. I'm at a loss why this is happening and I can't find any ssh options that would explain it. --update-- I just changed debug level to DEBUG. But before that I'm seeing a lot of the following in auth.log Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session opened for user root by (uid=0) Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session closed for user root ... Feb 1 04:36:26 greenpages sshd[7217]: reverse mapping checking getaddrinfo for nat-pool-xx-xx-xx-xx.myinternet.net [xx.xx.xx.xx] failed - POSSIBLE BREAK-IN ATTEMPT! ... Feb 1 04:37:31 greenpages sshd[7223]: Did not receive identification string from xx.xx.xx.xx ... My sshd_conf file settings are: # Package generated configuration file # See the sshd(8) manpage for details # What ports, IPs and protocols we listen for Port xxx # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel DEBUG # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM no ClientAliveInterval 60 AllowUsers myuser

  Read the article

• How to tackle dell support system? [closed]

  - by Nishant Kumar

  We have purchased a Dell Optiplex 9010 SSFV for our organization's work. Since the first installation two of the USB keyboard keys were not working properly. I had to press those keys two times simultaneously, on first time keys did not work and for for second time it printed two characters (as it were buffering first character.) Two keys that were not working properly: Hexangrave (Below the ESC key: `) Double Quotes (Left the enter key ") We registered our complaint with DELL and they suggested (with some hard to understand and weird ENGLISH accent) some test and tricks, such as switching to different ports, checking keyboard on different PC, and it worked well with diff. PC(with Windows 7 Home Premium installed). It was clear that it is an OS fault, hence they suggested to re-install OS. Problem began here, we have a project on the run and currently a video editing project setup on our system, so can't re-install system in hurry and also DELL persons were not providing any other solution such as updating keyboard driver, etc. Arguments I am a Software Engg. and don't think it is a feasible solution to re-install entire system for simple problems. This prob is coming since the fresh system installation, so I don't think it will solve the problem. Finally, I had to find solution myself and got it here, now I want to show my disappointment to dell persons or at least tell them that they should improve there support system to not advice to re-install entire system for that simple problems. Notes We have purchased 5 years NEXT business day support from DELL for around 8000 INR (Not for that kind of solutions from DELL). So can anyone tell me how to tackle dell support system officially, so that they will pay more attention in near future. Thanks

  Read the article

• Failed to start apache Can't open /etc/apache2/envvars

  - by bumperbox

  i have had this problem a couple of times now and i am not sure what is causing it Failed to start apache : .: 45: Can't open /etc/apache2/envvars when i look at a dir listing, i get these question marks next to envvars, does anyone know what that means? os is ubuntu 10 if that helps drwxr-xr-x 7 root root 4096 Jan 29 11:56 . drwxr-xr-x 83 root root 4096 Feb 4 10:34 .. -rw-r--r-- 1 root root 8113 Sep 29 01:52 apache2.conf -rw-r--r-- 1 root root 8027 Oct 3 22:26 apache2.conf.dpkg-old drwxr-xr-x 2 root root 4096 Jan 29 11:56 conf.d ?????????? ? ? ? ? ? envvars -rw-r--r-- 1 root root 0 Oct 3 22:25 httpd.conf ?????????? ? ? ? ? ? magic drwxr-xr-x 2 root root 4096 Jan 29 11:56 mods-available drwxr-xr-x 2 root root 4096 Jan 29 10:18 mods-enabled ?????????? ? ? ? ? ? ports.conf drwxr-xr-x 2 root root 4096 Jan 29 11:56 sites-available drwxr-xr-x 2 root root 4096 Jan 29 11:55 sites-enabled UPDATE Just heard back from the hosting company, they move my VPS to a new hardware node last night, and something at their end wasn't quite right which caused the issue

  Read the article

• suggestions for firewall/router project using *BSD or Linux

  - by Adeodatus

  Hi All, I have a project in mind and I'd love to hear some ideas on some open source solutions with COTS hardware. I have a few 24 and/or 48 port managed layer2 switches with customers potentially on each port (though its usually about 20-30). Right now the switch has a bridged network and backhaul the traffic to our core to a centralized DHCP server. I need to move them to a NAT solution and, while doing this, I'd like to protect the customers on each port from the customer traffic on the other ports. I also need to be able to port forward from the public side of the firewall/nat box to specific hardware on the inside of the nat machine (easy enough, I know). My first thoughts are to build an appliance-like box (the fewer moving parts the better) that can do filtering and NAT with rfc1918 an address range being handed out via a DHCP server on the appliance. A caching DNS server on the appliance would be a plus since we backhaul everything to the core. I'd like to run FreeBSD but I'm open. Now, to try to limit the broadcast traffic thats visible I was thinking of doing each port on the switch as a different vlan and have the switch do trunking to the private NIC on the FreeBSD/appliance. I'd probably need to do some magic on the freebsd NIC to get this working but it should. We have the parts to build these systems. So, does this make sense? Are there any other solutions out there that we don't have to spend money on but can use our parts to create something? Are there any good distros that could do this already (monowall)?? I may or may not admin this solution so a secure web configuration and management tool would be a plus in the other admins' minds. Thoughts?

  Read the article

• apache2: ssl_error_rx_record_too_long when visiting port 80? help!

  - by John

  Hi, I have an Ubuntu 10 x64 server edition machine. I got a second IP and configured /etc/network/interfaces like so (actual IPs and gateways removed): [code] auto lo iface lo inet loopback iface eth0 inet dhcp auto eth0 auto eth0:0 iface eth0 inet static address [ my first IP ] netmask 255.255.255.0 gateway [ my first gateway ] iface eth0:0 inet static address [ my second IP ] netmask 255.255.255.0 gateway [ my second gateway ] [/code] /etc/apache2/ports.conf: [code] Listen 80 NameVirtualHost [ my first IP ]:80 NameVirtualHost [ my second IP ]:80 # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 NameVirtualHost [ my first IP - some site is running SSL successfully using it ]:443 Listen 443 [/code] /etc/apache2/sites-enabled/mysite.conf: [code] ServerName mysite.com Include /var/www/mysite.com/djangoproject/apache/django.conf [/conf] [/code] Then when visiting http[mysite].com:80 or http[mysite].com (:// removed because serverfault doesn't allow me to post hyperlinks), I get: [code] An error occurred during a connection to [mysite].com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) [/code] My guess is that the configuration file is not being picked up, and apache is therefore looking for the default-ssl file, which is not in conf-enabled. If I were to configure that file properly, it seems I would successfully connect to whatever default directory is specified in the default-ssl file. But I want to connect to my website. Any ideas? Thanks in advance!

  Read the article

• Domain authentication over OPEN wireless pre-logon (Windows 7 Pro) - No logon servers avail

  - by Shadow00Caster

  I have a plethora of laptops that are joined to an AD domain. I have an enterprise wireless system setup, the users of these laptops will be using an OPEN unsecured SSID which will ultimately have a captive portal that uses Radius-AD auth and firewall rules to allow access pre-captive portal auth to the proper ip's/ports of DC's etc for auth etc. I already have other laptops/users connecting to another SSID with 802.11x and SSO, all works perfectly pre-logon etc. My problem is with this open network, for some reason I cannot get the machines to auth to AD. The laptops connect to the wireless network, I confirm this on the controller and can ping the laptop at startup. I sharked the wires on the 2 DC's that these machines auth to, I can see a DNS SOA update from a laptop im testing with and can ping that test laptop from both DC's. When I try to logon, "There are currently no logon servers available to service the logon request." The shark shows no incoming connections to either DC even though the laptop is connected and pingable. Any help is greatly appreciated.

  Read the article

• RRAS NAT not working on a certain computer

  - by legenden

  This is driving me crazy. I have a virtualized W2K8 server running RRAS. Every other computer or server on the network can access the internet through the NAT except one. On one server, it just won't work. I can ping the ip address of the NAT gateway just fine, and everything else works. (SMB, etc) DNS, which is hosted by the same server, also works just fine. I have even reinstalled the OS on the problem server and it still doesn't work. Recap of the steps I tried: There are 3 network cards in the server, I tried every one and different switch ports. Not a hardware problem. Reinstalled W2K8 R2 on server with the problem, didn't help. Tried the IP of the internet gateway directly - this did work (!). But I need NAT to work. All firewalls are disabled. Removed computer from domain, deleted computer membership in Active Directory Users and Computers and added it back. Disabled all other network adapters and set a static ip and specified the gateway ip manually. When I tracert a public IP, the first hop (or any other hop) comes up as: C:\>tracert www.google.com Tracing route to www.l.google.com [209.85.225.106] over a maximum of 30 hops: 1 * * * Request timed out. 2 * * * Request timed out. From a different computer, on which NAT works, the first hop comes up as: tracert www.google.com Tracing route to www.l.google.com [209.85.225.105] over a maximum of 30 hops: 1 <1 ms * <1 ms xxxx [10.5.1.1] This is the most bizarre problem I ever came across, and I realize that it's a long shot asking it here given all the details, but I'm pulling my hair out. Maybe someone has an idea...

  Read the article

• PORT FORWARDING TO PUT MY WEB SERVER ON THE INTERNET

  - by Chadworthington

  I went to http://canyouseeme.org/ to check to see what my external IP address. Regardless of what port I enter, it tells me that the port is blocked. I have a LinkSys router that basically has the default settings with the exception that I have WEP encrptin setup and I have forwarded a few ports, including 80 and 69. I forwarded them to the 192.x.x.103 IP address of the PC which is running IIS. That PC runs Symantec Endpoint Protection, which I right mouse clicked in the tray to Disable. These steps used to make my PC visible so I could host my own web site in IIS on port 80, or some other port, like 69. Yet, the Open Port tool cannot see my IP when it checks eiether port and when I navigate to http://my external ip/ I get "page cant be displayed" At first I was thinking that maybe Comcast is blocking port 80, but 69 doesnt work eiether. I do not see any other blockking set up in my router and, as I mentioned, I went with teh defaults except where discussed. This is a corporate PC and Symantec End Point Protecion is new to it (this previously worked on teh same PC with Symantec Protection Agent), but I thought that disabling Sym End Pt from the tray, that that would effectively neutralize it. I do not have the rights to kill the program itself. Any suggestions on what else to try to make my PC externally visible?

  Read the article

• fail2ban log parsing too slow on Raspberry Pi - options? [migrated]

  - by Gordon Morehouse

  I'm running fail2ban on a Raspberry Pi at 950MHz which I cannot overclock further. The Pi is occasionally subject to SYN floods on particular ports. I've set up iptables to throttle the rate of SYNs on the port of interest; when the throttle limits are exceeded, hosts which send SYNs are dropped into the REJECT chain and the particular SYN packet which exceeded the limit is logged. fail2ban then watches for these logged SYNs and, after seeing a few, temporarily bans the host for a short time (this is a transient issue in the app I'm working with). The problem is that the SYN floods can occasionally reach rates which are too fast for fail2ban to keep up with; I'll see 20-40 log messages per second, and eventually fail2ban falls behind and becomes ineffective. To add insult to injury, it continues consuming a LOT of CPU as it tries to catch up. I have verified that DROP chained packets from hosts already banned by fail2ban are not logged, and thus do not add to its load. What are my options here? I have a few ideas, but no clear path forward. Could I make the log-parse regex "easier" so it takes fewer cycles? Would using iptables --log-prefix to put a token near the start of the log message, and/or otherwise simplifying/altering the fail2ban regex help? Here is the current fail2ban config line containing a regex: failregex = kernel:.*?SRC=(?:::f{4,6}:)?(?P<host>[\w\-.^_]+) DST.*?SYN Is there a faster way for fail2ban to watch for the packets exceeding the limits than parsing kern.log? Could fail2ban be run under PyPy instead of CPython with minimal nonstandard wizardry (the OS is Raspbian 7, so, mostly Debian 7)? Is there something better than fail2ban that I could use to watch for the packets which exceed the SYN limits, and after N exceeds in X seconds, temporarily put the offending IP into the iptables DROP bucket, and take it out when the ban timer expires? Again, I'd vastly prefer a solution that uses as much software available in Debian as possible, though I can build Debian packages in a pinch.

  Read the article

• How to connect through a proxy using Remote Desktop?

  - by scottmarlowe

  So I've got a home server running Windows Server 2003. I use a dual network card setup and Routing and Remote Access to link the internal, private network to the external connection. The external connection hooks directly to my cable modem (so no routers or other devices sitting between). The problem I'm having is that I can't connect remotely from a location outside the house (so connecting to the server's external connection) to the server using either Remote Desktop or VNC. I have enabled both ports in Routing and Remote Access's firewall to allow access, and I have enabled Remote Desktop in Windows Server 2003. The odd thing is that I can access my home server's SVN repository and I can even ping the server's IP. I am using the IP to attempt to connect, though I use a dyndns.com provided name to connect to my SVN repository, so it shouldn't make a difference (I know the IP is getting resolved correctly). Any ideas on where to start diagnosing this one? I haven't seen anything in my server's event log. If any other info is needed, let me know. Thanks. UPDATE: One last piece of information: We use a proxy server at work, which I'm nearly 100% sure is the culprit. I have a workaround--if I connect to our VPN (even though I'm already inside the building) I am able to connect to my home server. This is with VNC. However, is there a way to connect through a proxy using Remote Desktop? ONE MORE UPDATE: Indeed, it was the http proxy I'm sitting behind at work that was causing the issue. An acceptable workaround is to use my VPN connection to bypass the proxy, and I'm in!

  Read the article

• 0 connected nodes in datastax opscenter

  - by gansbrest

  Installed opscenterd on the separate node outside of the cluster, but within firewall ( aws security group ). Tested all possible ports between agents and opcenter server. No errors in the log.. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Initializing event storage. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Attempting to load all persisted alert rules 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done loading persisted alert rules 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done initializing event storage. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done loading persisted scheduled job descriptions 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: OpsCenter starting up. 2013-10-30 01:07:23+0000 [] INFO: Finished starting new cluster services for FC_Cluster 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.34.10.185 is version u'3.2.2' 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.32.37.251 is version u'3.2.2' 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.82.226.252 is version u'3.2.2' The most interesting part that I can see some data in the opscenter UI, when I stop agents, there is no data displayed, when I start - it show up again, but at the same time it shows 0 connected nodes. Storage capacity is even funnier - 3 of 0 nodes.. Any ideas why that could be happening?

  Read the article

• Automatically install driver on headless WHSv1 system

  - by Dan Neely

  I have one of the HP Mediasmart Windows Home Server v1 boxes. It's network port appears to have died a few days ago but the system is not giving any other sign of failure: No activity lights activate on either side of the cable when connected to my gigabit switch; when connected to one of my routers 100 megabit ports the lights turn on but it remains unreachable over the network and my router never lists it as among DHCP clients. I bought a USB-ethernet adapter to temporarily get it back online; but the adapter needs a driver to work which I can't install because the system is headless by design (no video out, no PCI/PCIe slots) with admin access only available via the WHS client or remote desktop. Both of those options require network connectivity and are consequently unavailable. I tried copying the drivers to a flash drive; but Windows either didn't look there or none of the drivers provided were suitable (Win8, Win7, or combined XP and Vista). I've been told that a USB WiFi adapter would have the same driver problem.

  Read the article

• Packet drop measured by ethtool, tcpdump and ifconfig

  - by Rayne

  Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

  Read the article

• Port translation in router causing some email to fail

  - by user22037

  We are in the process of setting up a spam filter (SAVASM). One change we are making is to push incoming email on port 25 through our spam filter/server but have users actually send their email on a different port. I am attempting to make this happen by using port address translation to send port 25 traffic to the SAVASM server IP. As a step in making this change I setup port translation without actually changing the IP addresses. The NAT rules for the email server went from one Static NAT rule with no port specified, to multiple Static NAT rules each with a port or group matching the Access Rules for that server (smtp, pop3, http, https, and some other custom ports). The problem we are running into is confusing. Some outgoing mail through this server is failing when the router has the multiple NAT rules with port translation settings. Email goes through fine FROM our email to our internal accounts and to Gmail. However email fails when FROM our client's email address TO our client's email or their personal Comcast. The only situation that worked for them was if they changed FROM to Comcast and then messages went through fine to both Comcast and the client's accounts. Switching back to regular Static NAT rule everything then worked for them. Does anyone have a clue as to what might be going on? We are on a Cisco ASA 5500 box.

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >