Search Results

Search found 2417 results on 97 pages for 'states'.

Page 85/97 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• Too many Tunnel Adapter Interfaces

  - by Tomas Lycken

  If I open a command prompt on my machine and type ipconfig /all, I see lots of Tunnel adapter Local Area Connection* 9: Media state . . . . . . . . . . . . . : Media disconnected Connection-specific DNS Sufficx . . . : Description . . . . . . . . . . . . . : Microsoft 6to4 Adapter #5 Physical address. . . . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . . . : No Autoconfiguration Enabled . . . . . . : Yes In fact, they're so many that my "real" adapters are pushed out of the stack, and can't be seen anymore. Is there any flag I can use on ipconfig to hide all virtual interfaces? Or is there some other way around this problem? Since they always say "Media disconnected" I suppose disabling could be an option, but if possible I'd rather not turn any functionality off. I just want to control what output I get from ipconfig. Also, I know these are related to IPv6 stuff. However, most of what I find on google merely states what these are, and that they're harmless - nothing about hiding/removing them.

  Read the article

• XenServer 6.0.2 path to installation media contains non-ascii characters

  - by cmaduro

  XenServer 6.0.2 install fails no matter what I do. I have confirmed that the md5 checksum on my ISO file is good. I tried installing from a mounted ISO file (remotely via iKVM). I tried installing from physical media. I tried installing from a bootable USB stick (using syslinux + contents of the ISO) All attempts have yielded the same result: When verifying the installation media, at 0% initializing, the following is reported: "Some packages appeared to be damaged." followed by a list of pretty much all the gz2 and rpm packages. If I skip the media verification the installer proceeds and then gives me an error when it reaches "Installing from base pack" at 0% which states "An unrecoverable error has occurred. The error was: 'ascii' codec can't decode byte 0xff in position 20710: ordinal not in range(128) Please refer to your user guide, or contact a Technical Support Representative, for further details" there is one option left which is to reboot. Apparently at some point during the processing of the repositories on the installation media non-ascii characters are found, which causes the installer to quit. How do I fix this? Here are my specs TYAN S8236 motherboard 2 AMD Opteron 6234 processors LSI2008 card connected to 2 1TB Seagate Constellation drives SATA, 1 500GB Corsair m4 SSD SATA and 1 Corsair Forse 3 - 64GB SSD SATA Onboard SATA connected to a slim DVD-+RW. Onboard SAS connected to 2 IBM ESX 70GB 10K SAS drives (for XenServer) 256GB memory ================================================================================= Comments: According to pylonsbook.com "chances are you have run into a problem with character sets, encodings, and Unicode" – cmaduro 10 hours ago A clue is provided by "vmware.com/support/vsphere5/doc/…; Data migration fails if the path to the vCenter Server installation media contains non-ASCII characters When this problem occurs, an error message similar to: 'ascii' codec can't decode byte 0xd0 in position 30: ordinal not in range(128) appears, and the installer quits unexpectedly during the data migration process. – cmaduro 10 hours ago This is an error that python throws. And guess what, the .py extention of the file you have to edit in this link community.spiceworks.com/how_to/show/1168 means the installer is written in python. Python is interpreted, so now to find the install file responsible for this error. – cmaduro 6 hours ago The file that generates the error upon verification is /opt/xensource/installer/tui/repo.py. The error message appears around line 359. – cmaduro 2 hours ago I am fairly sure that the install error is generated somewhere in repository.py as the backend.py file throws errors while methods in that file are being called. Perhaps all errors can be traced back to this file. – cmaduro 1 hour ago

  Read the article

• Data loss through permissions change?

  - by charliehorse55

  I seem to have deleted some files on my media drive, simply by changing the permissions. The Story I have many operating systems installed on my computer, and constantly switch between them. I bought a 1TB HD and formatted it as HFS+ (not journaled). It worked well between OSX and all of my linux installations while having much better metadata support than NTFS. I never synced the UIDs for my operating systems so the permissions were always doing funny things. Yesterday I tried to fix the permissions by first changing the UIDs of the other operating systems to match OSX, and then changing the file ownership of all files on the drive to match OSX. About 50% of the files on the drive were originally owned by OSX, the other half were owned by the various linux installations. I started to try and change the file permissions for the folders, and that's when it went south. The Commands These commands were run recursively on the one section of the drive. sudo chflags nouchg sudo chflags -N sudo chown myusername sudo chmod 666 sudo chgrp staff The Bad Sometime during the execution of these commands, all of the files belonging to OSX were deleted. If a folder had linux based files it would remain intact but any folder containing exclusively OSX files was erased. If a folder containing linux files also contained a subfolder with only OSX files, the sub folder would remain but is inaccesible and displays a file size of 0 bytes. Luckily these commands were only run on the videos folder, I also have a music folder with the same issue but I did not execute any of these commands on it. Effectively I have examples of the file permissions for all 3 states - the linux files before and after, and the OSX files before. OSX File Before -rw-r--r--@ 1 charliehorse 1000 3634241 15 Nov 2008 /path/to/file com.apple.FinderInfo 32 Linux File before: -rw-r--r--@ 1 charliehorse 1000 5321776 20 Sep 2002 /path/to/file/ com.apple.FinderInfo 32 Linux File After (Read only): (Different file, but I believe the same permissions originally) -rw-rw-rw-@ 1 charliehorse staff 366982610 17 Jun 2008 /path/to/file com.apple.FinderInfo 32 These files still exist so if there are any other commands to run on them to determine what has happened here, I can do that. EDIT Running ls on one of the "empty" deleted OSX folders yields this: ls: .: Permission denied ls: ..: Permission denied ls: subdirA: Permission denied ls: subdirB: Permission denied ls: subdirC: Permission denied ls: subdirD: Permission denied I believe my files might still be there, but the permissions are screwed.

  Read the article

• Can an administration extraction of an MSI file perform registry and/or system wide changes?

  - by Wil

  I am always getting MSI (or setup EXEs which are basically MSI) files, and half the time they really do not need to be a setup. Microsoft is probably one of the biggest sources - almost every time I want to download a little source code sample, it has a MSI which if you install, only usually has three files. I would rather not do an install and add it to the add/remove programs and who knows what else (although I am sure it wouldn't be that bad) for the sake of three files! For this reason, I always use the following command: MSIEXEC /a <filename.msi> /qb TARGETDIR=<directory name> Now, this works fine and I have never had problems... However, I was just browsing some articles on Technet and found the following resource about administration installs. Apparently, MSI files can have two sequences: The AdminUISequence Table and the AdminExecuteSequence Table. I am not so worried about the AdminUISequence Table as it states that "The installer skips the actions in this table if the user interface level is set to basic UI or no UI", and this is what the /qb switch I use does. However, there is nothing similar written against AdminExecuteSequence Table. I realise that many people who write MSI files simply do it for a single end user and probably do not even touch the admin install options, however, is it possible for them to set items that can affect the system and if so, is there a fail proof way of extracting? I do already use 7-zip, however despite it being on the "supported" page, MSI support is lacking... well... completely sucks. It looses the file names and is generally useless. They have a bug which was closed with no reason/resolution over three years ago, and I opened a forum post and haven't had a reply. I would not really want to install any additional programs if I could help it and just want peoples opinions on this. Thanks. edit - Should also say, I run with UAC on, and I have never ever had a elevation prompt whilst performing the MSIEXEC operation, so I am guessing I have never had a system wide change, however, I am still curious as to if it is possible... As if changes (even just to the user) are possible I would do this locally/in a VM and never on a server or place of importance!

  Read the article

• SSL_CLIENT_CERT_CHAIN not being passed to backend server

  - by nidkil

  I have client certificate configured and working in Apache. I want to pass the PEM-encoded X.509 certificates of the client to the backend server. I tried with the SSLOptions +ExportCertData. This does nothing at all, while the documentation states it should add SSL_SERVER_CERT, SSL_CLIENT_CERT and SSL_CLIENT_CERT_CHAINn (with n = 0,1,2,..) as headers. Any ideas why this option is not working? I then tried setting the headers myself using RequestHeader. This works fine for all variables except SSL_CLIENT_CERT_CHAIN. It shows null in the header. Any ideas why the certificate chain is not being filled? This is my first Apache configuration: <VirtualHost 192.168.56.100:443> ServerName www.test.org ServerAdmin webmaster@localhost DocumentRoot /var/www ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined SSLEngine on SSLProxyEngine on SSLCertificateFile /etc/apache2/ssl/certs/www.test.org.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.test.org.key SSLCACertificateFile /etc/apache2/ssl/ca/ca.crt <Proxy *> AddDefaultCharset Off Order deny,allow Allow from all </Proxy> <Location /carbon> ProxyPass http://www.test.org:9763/carbon ProxyPassReverse http://www.test.org:9763/carbon </Location> <Location /services/GbTestProxy> SSLVerifyClient require SSLVerifyDepth 5 SSLOptions +ExportCertData ProxyPass http://www.test.org:8888/services/GbTestProxy ProxyPassReverse http://www.test.org:8888/services/GbTestProxy </Location> </VirtualHost> This is my second Apache configuration: <VirtualHost 192.168.56.100:443> ServerName www.test.org ServerAdmin webmaster@localhost DocumentRoot /var/www ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined SSLEngine on SSLProxyEngine on SSLCertificateFile /etc/apache2/ssl/certs/www.test.org.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.test.org.key SSLCACertificateFile /etc/apache2/ssl/ca/ca.crt <Proxy *> AddDefaultCharset Off Order deny,allow Allow from all </Proxy> <Location /carbon> ProxyPass http://www.test.org:9763/carbon ProxyPassReverse http://www.test.org:9763/carbon </Location> <Location /services/GbTestProxy> SSLVerifyClient require SSLVerifyDepth 5 RequestHeader set SSL_CLIENT_S_DN "%{SSL_CLIENT_S_DN}s" RequestHeader set SSL_CLIENT_I_DN "%{SSL_CLIENT_I_DN}s" RequestHeader set SSL_CLIENT_S_DN_CN "%{SSL_SERVER_S_DN_CN}s" RequestHeader set SSL_SERVER_S_DN_OU "%{SSL_SERVER_S_DN_OU}s" RequestHeader set SSL_CLIENT_CERT "%{SSL_CLIENT_CERT}s" RequestHeader set SSL_CLIENT_CERT_CHAIN0 "%{SSL_CLIENT_CERT_CHAIN0}s" RequestHeader set SSL_CLIENT_CERT_CHAIN1 "%{SSL_CLIENT_CERT_CHAIN1}s" RequestHeader set SSL_CLIENT_VERIFY "%{SSL_CLIENT_VERIFY}s" ProxyPass http://www.test.org:8888/services/GbTestProxy ProxyPassReverse http://www.test.org:8888/services/GbTestProxy </Location> </VirtualHost> Hope someone can help. Regards, nidkil

  Read the article

• Why do I need to set up Autologon values in registry twice in before it works and can I fix this?

  - by jJack

  Background: As part an automated testing suite I am building, I need to set up Autologon on my virtual machines 'on demand'. By on demand, I mean that I don't want to necessarily pre-configure my VM or any snapshot to have Autologon set up already, for security reasons and also a huge business case. My solution so far: I'm copying a script to the guest machine and then using Sysinternals PsExec to execute it. The script is: reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultUserName /t REG_SZ /d myusername reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultPassword /t REG_SZ /d myfakepassword reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v DefaultDomainName /t REG_SZ /d mydomain reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v ForceAutoLogon /t REG_SZ /d 1 reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon" /f /v AutoAdminLogon /t REG_SZ /d 1 reg add "hklm\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\AutoLogonChecked" /f /ve /d 1 Note: I don't believe AutoLogonChecked is required for machines post Windows 2000 but I'm doing it just in case for now. Maybe ForceAutoLogon isn't either, not sure yet. The Problem: I see PsExec executes this properly and all the values are in the registry, however when I restart the machine, the user isn't automatically logged on...When I run this a second time then restart the machine, the user is finally logged on. A diff between the registry states shows that the first time I run this, it is missing both the "1" for AutoAdminLogon, and also the DefaultPassword key. The second time I execute it, these values are correctly intact as I intended. So, what is going on here? Is this expected? This post claims in the end that it really all just works (the problem was that a logoff script was setting off the values). Doesn't seem to work for me however. Note this seems unique to Windows 7, does not occur in Windows XP Also note that you don't need PsExec to recreate the issue - just modify the registry yourself EDIT/update: Login interactively and run script (so, not executing it remotely), logging off automatically logs me back in (so, it works) remotely execute the script in guest when I'm interactively logged in, logging off automatically logs me back in (so, it works) remotely execute the script in guest when with non-interactive session if I log in afterwards (so, interactive now) then back off, it logs me back in (so, it then works) EDIT/update 2: This only occurs for Win7x86, Win7x64, Win8x64. This does not occur for Windows XP

  Read the article

• Assign fixed IP address via DHCP by DNS lookup

  - by Janoszen

  Preface I'm building a virtualization environment with Ubuntu 14.04 and LXC. I don't want to write my own template since the upgrade from 12.04 to 14.04 has shown that backwards compatibility is not guaranteed. Therefore I'm deploying my virtual machines via lxc-create, using the default Ubuntu template. The DNS for the servers is provided by Amazon Route 53, so no local DNS server is needed. I also use Puppet to configure my servers, so I want to keep the manual effort on the deployment minimal. Now, the default Ubuntu template assigns IP addresses via DHCP. Therefore, I need a local DHCP server to assign IP addresses to the nodes, so I can SSH into them and get Puppet running. Since Puppet requires a proper DNS setup, assigning temporary IP addresses is not an option, the client needs to get the right hostname and IP address from the start. Question What DHCP server do I use and how do I get it to assign the IP address based only on the host-name DHCP option by performing a DNS lookup on that very host name? What I've tried I tried to make it work using the ISC DHCP server, however, the manual clearly states: Please be aware that only the dhcp-client-identifier option and the hardware address can be used to match a host declaration, or the host-identifier option parameter for DHCPv6 servers. For example, it is not possible to match a host declaration to a host-name option. This is because the host-name option cannot be guaranteed to be unique for any given client, whereas both the hardware address and dhcp-client-identifier option are at least theoretically guaranteed to be unique to a given client. I also tried to create a class that matches the hostname like this: class "my-client-name" { match if option host-name = "my-client-name"; fixed-address my-client-name.my-domain.com; } Unfortunately the fixed-address option is not allowed in class statements. I can replace it with a 1-size pool, which works as expected: subnet 10.103.0.0 netmask 255.255.0.0 { option routers 10.103.1.1; class "my-client-name" { match if option host-name = "my-client-name"; } pool { allow members of "my-client-name"; range 10.103.1.2 10.103.1.2; } } However, this would require me to administer the IP addresses in two places (Amazon Route53 and the DHCP server), which I would prefer not to do. About security Since this is only used in the bootstrapping phase on an internal network and is then replaced by a static network configuration by Puppet, this shouldn't be an issue from a security standpoint. I am, however, aware that the virtual machine bootstraps with "ubuntu:ubuntu" credentials, which I intend to fix once this is running.

  Read the article

• Adaptec 5805 after reboot don't starting

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not included. It only works if the computer is shut down and turn off. Late i update firmware "Adaptec RAID 5805 Firmware Build 18948" How to fix the problem? add Log Configuration summary Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priorityHigh Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1 List item

  Read the article

• SQL server 2008 R2 installation error

  - by Sonia

  I have a windows 7,32 bit laptop. I am the administrator with all permissions. when I click on the SQL server 2008R2 set up file,it says : "SQL server set up has encountered the following error:Failed to retreive data for this request" click on OK. I have uninstalled all the components of SQL from control panel. I used Windows installer clean up to remove the files(which I must have not done ),but still no go. The summary.txt log says: Overall summary: Final result: Failed: see details below Exit code (Decimal): 847168662 Exit facility code: 638 Exit error code: 50326 Exit message: Failed to retrieve data for this request. Start time: 2012-05-25 14:59:15 End time: 2012-05-25 15:00:09 Requested action: RunRules Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\Detail.txt Exception help link: http%3a%2f%2fgo.microsoft.com%2ffwlink%3fLinkId%3d20476%26ProdName%3dMicrosoft%2bSQL%2bServer%26EvtSrc%3dsetup.rll%26EvtID%3d50000%26ProdVer%3d10.0.5500.0%26EvtType%3d0xEF814B06%400x92D13C14 Machine Properties: Machine name: EWAN-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: Australia OS language: English (United States) OS architecture: x86 Process architecture: 32 Bit OS clustered: No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation location: c:\385030d65c6ff61fb9\x86\setup\ Installation edition: EXPRESS User Input Settings: ACTION: RunRules CONFIGURATIONFILE: FEATURES: HELP: False INDICATEPROGRESS: False INSTANCENAME: QUIET: False QUIETSIMPLE: False RULES: GLOBALRULES,SqlUnsupportedProductBlocker,PerfMonCounterNotCorruptedCheck,Bids2005InstalledCheck,BlockInstallSxS,AclPermissionsFacet,FacetDomainControllerCheck,SSMS_IsInternetConnected,FacetWOW64PlatformCheck,FacetPowerShellCheck X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\ConfigurationFile.ini Detailed results: Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: The rule result report file is not available. Exception summary: The following is an exception stack listing the exceptions in outermost to innermost order Inner exceptions are being indented Exception type: Microsoft.SqlServer.Management.Sdk.Sfc.EnumeratorException Message: Failed to retrieve data for this request. Data: HelpLink.ProdName = Microsoft SQL Server HelpLink.BaseHelpUrl = http://go.microsoft.com/fwlink HelpLink.LinkId = 20476 DisableWatson = true Stack: at Microsoft.SqlServer.Setup.Chainer.Workflow.PendingActions.InvokeActions(WorkflowObject metaDb, TextWriter loggingStream) at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionEngine.RunActionQueue() at Microsoft.SqlServer.Setup.Chainer.Workflow.Workflow.RunWorkflow(HandleInternalException exceptionHandler) at Microsoft.SqlServer.Chainer.Setup.Setup.RunRequestedWorkflow() at Microsoft.SqlServer.Chainer.Setup.Setup.Run() at Microsoft.SqlServer.Chainer.Setup.Setup.Start() at Microsoft.SqlServer.Chainer.Setup.Setup.Main() Inner exception type: Microsoft.SqlServer.Configuration.Sco.ScoException Message: Attempted to perform an unauthorized operation. Data: WatsonData = HKEY_LOCAL_MACHINE@SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Microsoft SQL Server 10 Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Configuration.Sco.SqlRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Discovery.RegistryKeyExistsPropertyValueProvider.GetPropertyValue(Object[] context) at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.GetPropertyValueFromProvider(IPropertyValueProvider propertyValueProvider, String machineName, Object[] context) at Microsoft.SqlServer.Discovery.ObjectInstanceSettings.IsObjectFound(String machineName, String idFilter) at Microsoft.SqlServer.Discovery.Product.FilterObjectSet(ArrayList objects, String idFilter) at Microsoft.SqlServer.Discovery.Product.GetData(EnumResult erParent) at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData() at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData(Request req, Object ci) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.GetData(Object connectionInfo, Request request) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request) Inner exception type: System.UnauthorizedAccessException Message: Attempted to perform an unauthorized operation. Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) Ineed to install SQL server 2008 R2 for one of the company softwares to work. Any immediate help will be greatly appreciated. Thanks Sonia

  Read the article

• IPvsadm not equally balancing on wlc scheduler

  - by davidsmalley

  For some reason, ipvsadm does not seem to be equally balancing the connections between my real servers when using the wlc or lc schedulers. One real server gets absolutely hammered with requests while the others receive relatively few connections. My ldirectord.cf file looks like this: quiescent = yes autoreload = yes checktimeout = 10 checkinterval = 10 # *.site.com http virtual = 111.111.111.111:http real = 10.10.10.1:http ipip 10 real = 10.10.10.2:http ipip 10 real = 10.10.10.3:http ipip 10 real = 10.10.10.4:http ipip 10 real = 10.10.10.5:http ipip 10 scheduler = lc protocol = tcp service = http checktype = negotiate request = "/lb" receive = "Up and running" virtualhost = "site.com" fallback = 127.0.0.1:http The weird thing that I think may be causing the problem (but I'm really not sure) is that ipvsadm doesn't seem to be tracking active connections properly, they all appear as inactive connections IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 111.111.111.111:http lc -> 10.10.10.1:http Tunnel 10 0 10 -> 10.10.10.2:http Tunnel 10 0 18 -> 10.10.10.3:http Tunnel 10 0 3 -> 10.10.10.4:http Tunnel 10 0 10 -> 10.10.10.5:http Tunnel 10 0 5 If I do ipvsadm -Lnc then I see lots of connections but only ever in ESTABLISHED & FIN_WAIT states. I was using ldirectord previously on a Gentoo based load balancer and the activeconn used to be accurate, since moving to Ubuntu 10.4 LTS something seems to be different. # ipvsadm -v ipvsadm v1.25 2008/5/15 (compiled with popt and IPVS v1.2.1) So, is ipvsadm not tracking active connections properly and thus making load balancing work incorrectly and if so, how do I get it to work properly again? Edit: It gets weirder, if I cat /proc/net/ip_vs then it looks like the correct activeconns are there IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP B86A9732:0050 rr -> 0AB42453:0050 Tunnel 10 1 24 -> 0AB4321D:0050 Tunnel 10 0 23 -> 0AB426B2:0050 Tunnel 10 2 25 -> 0AB4244C:0050 Tunnel 10 2 22 -> 0AB42024:0050 Tunnel 10 2 23

  Read the article

• Where to get laptop replacement parts?

  - by wai

  I am sure some of us have older laptops that still works but just one or two parts started not working very well. However, to send it back to the manufacturer for repair might not be worth the money (as some of them even charge consultation fees just to have it checked) as these old laptops are most probably well beyond warranty. Replacing these one or two parts could give your laptop a new lease of life. For example, I have a Dell Inspiron 640m which the fan recently failed. Everything else still works. I know enough to open up the laptop (after reading the service manual) and put it back together again, hence a replacement fan could save it. However, finding these parts turned out to be difficult. I guess I wouldn't be able to get it from Dell since I have been searching around the Dell forums and concluded if I were going to get Dell to at least talk to me, I would have to pay some money (since my warranty expired). I found this online:- http://www.parts-people.com/index.php?action=item&id=3725 However, as I don't live in the United States, shipping alone would cost me 3 times more than the part in question. In addition, if there's a problem, it would be difficult because I probably would have to mail the parts back (costing more money). One of my friend spilled water on her Macbook, she sent it back to Apple and they told her the cost of repairing it exceeds that of buying a new Macbook. They probably have to change everything except the LCD screen. I opened it up and found that most of the parts are still working, only the RAM had fried. Replaced it and it's working again. For some time before discovering only the RAM fried, I was toying with the idea of replacing the logic board myself but looks like I didn't have to. =) Now I know there's a site for Macbooks used replacement parts:- http://www.ifixit.com/ The question is, does anyone know where to get replacement parts at their own locality? It might benefit the community as a whole. Someone might know a local computer store that sells precisely just the things we needed (for now, I hope to find a shop that sells just the fan). If you own a laptop which you had an easy experience finding the replacement parts, do post that as well. PS: I wish laptop manufacturers have outlets where they sell these replacement parts (or at least let you place an order).

  Read the article

• X:\ is not accessible. Insufficient system resources exist to complete the requested service. Help [

  - by Katherine

  I keeping getting the error message from above on multiple computers that I administer. I wasn't sure if I should be posting this on SuperUser or ServerFault so my apologizes if it should go there... Basically, I have at least 5 computers of varying ages (some fresh out of the box!) throwing the above error. X:\ is one of our network drives that is mapped for users. Most of the time if you shut down the biggest application it will fix the problem, but it's becoming an increasing issue, and I can't keep running around fixing it manually. I have tried to do some research, but most of it just states the obvious without supplying a permanent fix. The machines are all running Win XP SP3, with at least 2gb of ram. Sorry for the delay in getting back to people... a lot of good questions. To respond back to people... It is a windows 2003 server that houses the file share. We have about 175 users, however i cannot state how many are actually accessing the information at a single moment. Considering that this is our largest file share, I would say that probably at least 100+. The files we work with are large, but not that big considering that we do a lot of graphical and video work. ~50mb. That being said, this is error occurs simply when trying to gain access to the server itself, not actual files. When I say close a program, I mean that it can be any program. It doesn't matter which program. It varies from machine to machine, and from day to day. Some days it is Firefox, some days it is Outlook, some days it is Excel. There doesn't seem to be a common bond behind which application could be causing the problem. Thank you for the articles, and the recommendation on paging files. I will have to look into that. None of our computers are set to hibernate, so I am going to rule that out.

  Read the article

• How to unlock and remove a protected partition from Prestigio USB stick?

  - by mr.b

  Ok, so, I have one of those fancy schmancy devices, which is given to me by a frustrated friend of mine. Device is a Prestigio Leather 8GB, which identifies itself to Linux host as: Bus 001 Device 006: ID 1307:0165 Transcend Information, Inc. 2GB/4GB Flash Drive Kernel messages as USB device is plugged in: kernel: [ 2769.580042] usb 1-9: new high speed USB device using ehci_hcd and address 7 kernel: [ 2769.714782] scsi8 : usb-storage 1-9:1.0 kernel: [ 2770.713937] scsi 8:0:0:0: Direct-Access 8192MB flash drive 1.00 PQ: 0 ANSI: 2 kernel: [ 2770.714535] scsi 8:0:0:1: Direct-Access 8192MB flash drive 1.00 PQ: 0 ANSI: 2 kernel: [ 2770.715734] sd 8:0:0:0: Attached scsi generic sg3 type 0 kernel: [ 2770.716108] sd 8:0:0:1: Attached scsi generic sg4 type 0 kernel: [ 2770.722175] sd 8:0:0:0: [sdc] 962560 512-byte logical blocks: (492 MB/470 MiB) kernel: [ 2770.722657] sd 8:0:0:0: [sdc] Write Protect is on kernel: [ 2770.731078] sd 8:0:0:1: [sdd] 14012416 512-byte logical blocks: (7.17 GB/6.68 GiB) kernel: [ 2770.731215] sdc: kernel: [ 2770.738251] sd 8:0:0:1: [sdd] Write Protect is off kernel: [ 2770.880328] kernel: [ 2770.885876] sd 8:0:0:0: [sdc] Attached SCSI removable disk kernel: [ 2770.887442] sdd: unknown partition table kernel: [ 2771.049605] sd 8:0:0:1: [sdd] Attached SCSI removable disk So, symptoms are typical for U3-like devices: two separate devices inside of a single flash device. Windows sees it also as two identical usb devices, and mounts two separate drives to system, whereas first one presents itself as a CDROM device, holding a write-protected content, and second is a regular flash-disk partition, that "can" be written to. However, it seems like it's broken in some weird way, since it won't let me write anything to it, format it, nothing, but that's not the issue right now. Question: How can I unlock entire USB stick so it appears to system as a single, 8GB device which can be partitioned and used normally, without restrictions? Since it appeared to be an U3 device, I have tried standard utilities: both U3 Uninstaller by u3.com (found on SoftPedia), and opensource u3_tool from sourceforge (on both Windows and Linux). First utility failed to even detect USB stick as U3 device (simply stood idle while I re-plugged stick several times), while second tool failed with some obscure error about SCSI command unable to do something (I might be able to provide exact errors when I switch back to windows). u3_tool -i /dev/sg3 (Display device info) fails with u3_partition_info() failed: Device reported command failed: status 1 ...and every other option fails with same error, minus first part which states which command precisely has failed. So, apparently, this isn't a U3 device. Or, if it is, it doesn't behave like one. I read on a few occasions that this device protection is done by special command sent to device which tells it to lock itself, and so there should be an unlock command, that would set drive straight. Does anyone have any idea about what could I do to this device to fix it? P.S. I also mentioned a problem with being unable to use second "drive", but I'll tackle that problem when (and if) I manage to merge those two devices into one...

  Read the article

• Where to get laptop replacement parts?

  - by wai

  I am sure some of us have older laptops that still works but just one or two parts started not working very well. However, to send it back to the manufacturer for repair might not be worth the money (as some of them even charge consultation fees just to have it checked) as these old laptops are most probably well beyond warranty. Replacing these one or two parts could give your laptop a new lease of life. For example, I have a Dell Inspiron 640m which the fan recently failed. Everything else still works. I know enough to open up the laptop (after reading the service manual) and put it back together again, hence a replacement fan could save it. However, finding these parts turned out to be difficult. I guess I wouldn't be able to get it from Dell since I have been searching around the Dell forums and concluded if I were going to get Dell to at least talk to me, I would have to pay some money (since my warranty expired). I found this online:- http://www.parts-people.com/index.php?action=item&id=3725 However, as I don't live in the United States, shipping alone would cost me 3 times more than the part in question. In addition, if there's a problem, it would be difficult because I probably would have to mail the parts back (costing more money). One of my friend spilled water on her Macbook, she sent it back to Apple and they told her the cost of repairing it exceeds that of buying a new Macbook. They probably have to change everything except the LCD screen. I opened it up and found that most of the parts are still working, only the RAM had fried. Replaced it and it's working again. For some time before discovering only the RAM fried, I was toying with the idea of replacing the logic board myself but looks like I didn't have to. =) Now I know there's a site for Macbooks used replacement parts:- http://www.ifixit.com/ The question is, does anyone know where to get replacement parts at their own locality? It might benefit the community as a whole. Someone might know a local computer store that sells precisely just the things we needed (for now, I hope to find a shop that sells just the fan). If you own a laptop which you had an easy experience finding the replacement parts, do post that as well. PS: I wish laptop manufacturers have outlets where they sell these replacement parts (or at least let you place an order).

  Read the article

• Restore single users Exchange 2003 mailbox from backup

  - by Campo

  I take weekly backups of exchange in full. I also take complete weekly backups of the entire server. It is a Server 2003 R2 with AD and Exchange 2003 all on one box. One users inbox has disappeared. She has 19000+ junk items now. It is possible the inbox got mixed into the junk. Regardless it is such a huge mess she is not going to go through all of that.... I want to restore he mailbox from the backup. I followed this MS KB http://support.microsoft.com/kb/823176 I had to use Method 3. I have a VM of Server 2003 R2 with exchange but I am having failures on the restore from NT backup. The backup log just states to check the application log.... Application log points to backup log... Only info Is failed to restore Only thing different is the computer name... The only error I can find is in the Application log. Information Store Database not found All others just say that the backup failed. Any assistance is greatly appreciated. UPDATE I have successfully proven I can restore the DB into a recovery storage group in my VM Unfortunately due to the actual account being on a different store I am unable to do the recovery... Error is The attempt to log on to the Microsoft Exchange Server computer has failed. The MAPI provider failed. Microsoft Exchange Server Information Store ID no: 8004011d-0512-00000000 Two questions QUESTION 1 Should I repeat my steps on the production exchange server in the recover storage group? then merge into her original account? I am just concerned with doing recovery like that on the live server.... QUESTION 2 Is there any way I can extract her .PST from my recovery VM and then import into her outlook? On the Recovery VM: I restored the raw DB from my full backup repaired it with ESEUTIL then mounted in the recovery store. Was thinking I could just repeat and mount in the main store on the VM? Thanks for the suggestions.

  Read the article

• Unecrypted Image of Truecrypt-Encrypted System Partition

  - by Dexter

  The general tenor around the internet seems to be that you can't create images of system partitions that have been encrypted (with truecrypt) other than with dd or similar sector-by-sector copy tools. These files however are very impractical given their size (and are obviously incompressible) which makes keeping multiple states/backups of your system partition rather expensive (..especially considering current hdd prices). The problem is that backup tools (like Acronis True Image, Clonezilla, etc.) won't give you the option to create an image of (mounted/opened) Truecrypt partitions, or that there is no recovery environment for restoring the backup, that would allow to run truecrypt before doing any actual restoring. After some trial and error however, I believe I have found a very simple way. Since Truecrypt (running in Linux) creates a virtual block device, that it uses for mounting the unencrypted partitions into the file system, partclone can be used for creating/restoring images. What I did: boot up a linux live disk mount/open the drive/device/partition in truecrypt unmount the filesystem mount point again, like so: umount /media/truecryptX ("X" being the partition number assigend by truecrypt) use partclone (this is what clonezilla would do too, except that clonezilla only offers you to back up real drive partitions, not virtual block devices): partclone.ntfs -c -s /dev/mapper/truecryptX -o nameOfBackupFile for restoring steps 1-3 remain the same, and step 4 is partclone.ntfs -r -s nameOfBackupFile -o /dev/mapper/truecryptX A backup and test-restore of the system (with this method) seems to have worked fine (and the changed settings were reverted to the backup-state). The backup file is ~40 GB (and compressible down to <8GB with 7zip/LZMA2 on the "fast" setting). I can't quite believe that I'm the only one that wants to create images of encrypted drives, but doesn't want to waste 100GB on the backup of one single system state. So my question now is, given how simple this was, and that no one seems to mention anywhere that this is possible - did I miss something? or did I do something wrong? Is there any situation that I didn't think of where this method will fail? Obviously, the backup file needs to be stored in some other encrypted place in order to still remain confidential, since it is unencrypted. Also, in order to do a full "bare metal" restore, one would have to actually first (re-)install Windows, encrypt it, and only then restore the backup file. The funny thing however is that you won't need to backup any partition tables, etc. since the reinstall will effectively take care of that. Is there anything else? This is imho still a lot better than having sector-by-sector images..

  Read the article

• Sony VGN-NR260E "External Device Boot"

  - by user72158

  [A LITTLE BACKGROUND] On all modern Dell computers pushing the F12 on bios boot will allow for a screen that lets you choose what boot option you need. For example if I want to boot off of a USB flash drive to boot into a live Linux distribution in order to clean virus's on netbooks that do not have CD drives to boot from I would push F12 and choose USB device from the list of options. If this does not show up then I can always go to the F2 bios setup and choose flash drive to be the first option. When I restart the computer it will boot into the flash device. I understand that I can purchase an external USB CD drive and then boot from that. I do not want to use that option. The reason for using a flash device instead of a CD is: A: This USB flash device has several different boot OS's on it that are used. B: The antivirus disks are updated often and burning cd's and throwing away others is wasteful compared to simply updating a flash drive. There is nothing wrong with the flash drive. It works perfect on many other PC's. [PROBLEM] Booting this flashdrive has been working for years on hundreds of computers... I just have this ONE computer that I cannot figure out how to get it to boot on... I have a Sony Vaio that will not boot to this device. I've tried pushing every key combo I can think of (F12, Esc, Del, F10...) and none of these key combinations will bring up the boot menu. I chose F2 and went into the bios and changed the first boot device to USB flash device. This did not work either. There is an astrix next to the device and the note states: "This Drive is available when External Device Boot is Enable." [WHAT I NEED] I need to know How to enable External Device Boot on the Sony Vaio VGN-NR260E laptop. OR How to bring up the Boot Menu to allow me to boot off a flash device. Thanks for anyone that can help!

  Read the article

• Adaptec 5805 not recognized after reboot

  - by Rakedko ShotGuns

  After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

  Read the article

• libreadline history lines combine

  - by jettero

  This has been driving me crazy for about three years. I don't know how to fully describe the problem, but I think I can finally describe a way to recreate it. Your milage may vary. I have a mixture of ubuntu server and desktop machines of various versions and a few gentoo machines with various states of disrepair. They all seem to kindof do their own thing, although with similarities. Try this and let me know if you see the same thing. pop open two xterms (TERM=xterm) resize one so they're not the same issue screen -R test1 in one (TERM=screen) and screen -x test1 in the other hooray, typing in one shows up in the other; although notice that their different size produces artifacts and things issue a couple commands in your shell hit ^AF in the one that doesn't fit quite right, now it fits!! scroll back over the history a little goto 6 Eventually you'll notice a couple history lines combine. If you don't, then it's something unique to my setup, which spans various distributions and computers; so that's a confusing concept to me. If you see the thing I'm seeing then this: bash$ ls -al bash$ ps auxfw becomes this: bash$ ls -al; ps auxfw It doesn't happen every time. I have to really play with it — unless I don't want it to happen, then it always does. On some systems (or combinations), I get a line separator like the example above. On some systems, I do not. That I get the line separator on some systems seems to indicate to me that bash supports this behavior. Its history is entirely handled by libreadline and after perusing (ie, carefully reading) the man pages, I couldn't find a single readline setting for combining two history lines. Nor can I find anything in the bash manpage. So, how can I invoke this on purpose? Or, if I can't do that, how can I disable it completely? I would take either answer as a solution. Currently, I only see it when I don't want it.

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

• Assign fixed IP address via DHCP by DNS lookup

  - by Janoszen

  Preface I'm building a virtualization environment with Ubuntu 14.04 and LXC. I don't want to write my own template since the upgrade from 12.04 to 14.04 has shown that backwards compatibility is not guaranteed. Therefore I'm deploying my virtual machines via lxc-create, using the default Ubuntu template. The DNS for the servers is provided by Amazon Route 53, so no local DNS server is needed. I also use Puppet to configure my servers, so I want to keep the manual effort on the deployment minimal. Now, the default Ubuntu template assigns IP addresses via DHCP. Therefore, I need a local DHCP server to assign IP addresses to the nodes, so I can SSH into them and get Puppet running. Since Puppet requires a proper DNS setup, assigning temporary IP addresses is not an option, the client needs to get the right hostname and IP address from the start. Question What DHCP server do I use and how do I get it to assign the IP address based only on the host-name DHCP option by performing a DNS lookup on that very host name? What I've tried I tried to make it work using the ISC DHCP server, however, the manual clearly states: Please be aware that only the dhcp-client-identifier option and the hardware address can be used to match a host declaration, or the host-identifier option parameter for DHCPv6 servers. For example, it is not possible to match a host declaration to a host-name option. This is because the host-name option cannot be guaranteed to be unique for any given client, whereas both the hardware address and dhcp-client-identifier option are at least theoretically guaranteed to be unique to a given client. I also tried to create a class that matches the hostname like this: class "my-client-name" { match if option host-name = "my-client-name"; fixed-address my-client-name.my-domain.com; } Unfortunately the fixed-address option is not allowed in class statements. I can replace it with a 1-size pool, which works as expected: subnet 10.103.0.0 netmask 255.255.0.0 { option routers 10.103.1.1; class "my-client-name" { match if option host-name = "my-client-name"; } pool { allow members of "my-client-name"; range 10.103.1.2 10.103.1.2; } } However, this would require me to administer the IP addresses in two places (Amazon Route53 and the DHCP server), which I would prefer not to do. About security Since this is only used in the bootstrapping phase on an internal network and is then replaced by a static network configuration by Puppet, this shouldn't be an issue from a security standpoint. I am, however, aware that the virtual machine bootstraps with "ubuntu:ubuntu" credentials, which I intend to fix once this is running.

  Read the article

• Nagios core Event Handler not working

  - by sivashanmugam

  Nagios Event Handler is not triggering when the service is taking more time to response or down. My configuration in below nagios.cfg enable_event_handlers=1 localhost.cfg define service { use generic-service host_name Server service_description test-server servicegroups test-service check_command check-service is_volatile 0 check_period 24x7 max_check_attempts 4 normal_check_interval 2 retry_check_interval 2 contact_groups testcontacts notification_period 24x7 notification_options w,u,c,r notifications_enabled 1 event_handler_enabled 1 event_handler recheck-service } command.cfg define command{ command_name recheck-service command_line /usr/local/nagios/libexec/alert.sh $SERVICESTATE$ $SERVICESTATETYPE$ $SERVICEATTEMPT$ } alert.sh file !/bin/sh set -x case "$1" in OK) # The service just came back up, so don't do anything... ;; WARNING) # We don't really care about warning states, since the service is probably still running... ;; UNKNOWN) # We don't know what might be causing an unknown error, so don't do anything... ;; CRITICAL) Aha! The HTTP service appears to have a problem - perhaps we should restart the server... Is this a "soft" or a "hard" state? case "$2" in We're in a "soft" state, meaning that Nagios is in the middle of retrying the check before it turns into a "hard" state and contacts get notified... SOFT) # What check attempt are we on? We don't want to restart the web server on the first check, because it may just be a fluke! case "$3" in Wait until the check has been tried 3 times before restarting the web server. If the check fails on the 4th time (after we restart the web server), the state type will turn to "hard" and contacts will be notified of the problem. Hopefully this will restart the web server successfully, so the 4th check will result in a "soft" recovery. If that happens no one gets notified because we fixed the problem! 3) echo -n "Going To Ping the Virtual Machine (3rd soft critical state)..." # Call the init script to restart the HTTPD server myresult=`/usr/local/nagios/libexec/check_http xyz.com -t 100 | grep 'time'| awk '{print $10}'` echo "Your Service Is taking the following time Delay" "$myresult Seconds" |mail -s "WARNING : Service Taken More Time To Response" [email protected] ;; esac ;; # The HTTP service somehow managed to turn into a hard error without getting fixed. # It should have been restarted by the code above, but for some reason it didn't. # Let's give it one last try, shall we? # Note: Contacts have already been notified of a problem with the service at this

  Read the article

• Switch flooding when bonding interfaces in Linux

  - by John Philips

  +--------+ | Host A | +----+---+ | eth0 (AA:AA:AA:AA:AA:AA) | | +----+-----+ | Switch 1 | (layer2/3) +----+-----+ | +----+-----+ | Switch 2 | +----+-----+ | +----------+----------+ +-------------------------+ Switch 3 +-------------------------+ | +----+-----------+----+ | | | | | | | | | | eth0 (B0:B0:B0:B0:B0:B0) | | eth4 (B4:B4:B4:B4:B4:B4) | | +----+-----------+----+ | | | Host B | | | +----+-----------+----+ | | eth1 (B1:B1:B1:B1:B1:B1) | | eth5 (B5:B5:B5:B5:B5:B5) | | | | | | | | | +------------------------------+ +------------------------------+ Topology overview Host A has a single NIC. Host B has four NICs which are bonded using the balance-alb mode. Both hosts run RHEL 6.0, and both are on the same IPv4 subnet. Traffic analysis Host A is sending data to Host B using some SQL database application. Traffic from Host A to Host B: The source int/MAC is eth0/AA:AA:AA:AA:AA:AA, the destination int/MAC is eth5/B5:B5:B5:B5:B5:B5. Traffic from Host B to Host A: The source int/MAC is eth0/B0:B0:B0:B0:B0:B0, the destination int/MAC is eth0/AA:AA:AA:AA:AA:AA. Once the TCP connection has been established, Host B sends no further frames out eth5. The MAC address of eth5 expires from the bridge tables of both Switch 1 & Switch 2. Switch 1 continues to receive frames from Host A which are destined for B5:B5:B5:B5:B5:B5. Because Switch 1 and Switch 2 no longer have bridge table entries for B5:B5:B5:B5:B5:B5, they flood the frames out all ports on the same VLAN (except for the one it came in on, of course). Reproduce If you ping Host B from a workstation which is connected to either Switch 1 or 2, B5:B5:B5:B5:B5:B5 re-enters the bridge tables and the flooding stops. After five minutes (the default bridge table timeout), flooding resumes. Question It is clear that on Host B, frames arrive on eth5 and exit out eth0. This seems ok as that's what the Linux bonding algorithm is designed to do - balance incoming and outgoing traffic. But since the switch stops receiving frames with the source MAC of eth5, it gets timed out of the bridge table, resulting in flooding. Is this normal? Why aren't any more frames originating from eth5? Is it because there is simply no other traffic going on (the only connection is a single large data transfer from Host A)? I've researched this for a long time and haven't found an answer. Documentation states that no switch changes are necessary when using mode 6 of the Linux interface bonding (balance-alb). Is this behavior occurring because Host B doesn't send any further packets out of eth5, whereas in normal circumstances it's expected that it would? One solution is to setup a cron job which pings Host B to keep the bridge table entries from timing out, but that seems like a dirty hack.

  Read the article

• Routing all data through an VPN tunnel with ppp

  - by Oliver

  I'm trying to create a VPN tunnel that forwards all data from the local machine to the VPN server. I'm using ppp-2.4.5 for this with the following configuration: pty "pptp <VPNServer> --nolaunchpppd" name <my login name> remotename PPTP usepeerdns require-mppe-128 file /etc/ppp/options.pptp persist maxfail 0 holdoff 5 I have a script in if-up.d with the following content: route del default eth0 route add default dev ppp0 Before starting the VPN tunnel my routing looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 2 0 0 eth0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 After starting the tunnel (via pon) it looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 12.34.56.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 Now the problem is, that the VPN tunnel seems to be looped into itself. If I run ifconfig after a few seconds without any traffic: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.10 netmask 255.255.0.0 broadcast 192.168.255.255 ether 00:01:2e:2f:ff:35 txqueuelen 1000 (Ethernet) RX packets 39931 bytes 6784614 (6.4 MiB) RX errors 0 dropped 90 overruns 0 frame 0 TX packets 34980 bytes 7633181 (7.2 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xfbdc0000-fbde0000 ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1496 inet 12.34.56.78 netmask 255.255.255.255 destination 12.34.56.1 ppp txqueuelen 3 (Point-to-Point Protocol) RX packets 7 bytes 94 (94.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 782863 bytes 349257986 (333.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 It states that already over 300 MiB have been send, ppp0 is only online since a few seconds and the connection isn't working anyway. Can someone please help me to fix the routing table, so that the traffic from ppp0 is not send again through ppp0 but instead goes to the remote server?

  Read the article

• 404 when doing safe-upgrade in lucid 64 box?

  - by Millisami

  Why I see 404 when doing sudo aptitude safe-upgrade in my lucid 64 box? deploy@li167-251:~$ sudo aptitude safe-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done The following packages will be upgraded: apache2 apache2-mpm-prefork apache2-threaded-dev apache2-utils apache2.2-bin apache2.2-common apt apt-utils base-files binutils bzip2 dpkg dpkg-dev gzip ifupdown krb5-multidev language-pack-en language-pack-en-base language-selector-common libatk1.0-0 libatk1.0-dev libavahi-client3 libavahi-common-data libavahi-common3 libbz2-1.0 libc-bin libc-dev-bin libc6 libc6-dev libc6-i686 libcups2 libfreetype6 libfreetype6-dev libglib2.0-0 libglib2.0-dev libgssapi-krb5-2 libgssrpc4 libgtk2.0-0 libgtk2.0-common libgtk2.0-dev libk5crypto3 libkadm5clnt-mit7 libkadm5srv-mit7 libkdb5-4 libkrb5-3 libkrb5-dev libkrb5support0 libldap-2.4-2 libldap2-dev libmysqlclient-dev libmysqlclient16 libnotify-dev libnotify1 libpam-modules libpam-runtime libpam0g libparted0debian1 libpng12-0 libpng12-dev libpq-dev libpq5 libssl-dev libssl0.9.8 libtiff4 libudev0 libusb-0.1-4 linux-libc-dev mountall mysql-client mysql-client-5.1 mysql-client-core-5.1 mysql-common mysql-server mysql-server-5.1 mysql-server-core-5.1 openssh-client openssh-server openssl parted python-apt sudo tzdata udev upstart ureadahead wget xulrunner-1.9.2 xulrunner-1.9.2-dev The following packages are RECOMMENDED but will NOT be installed: colibri debhelper fakeroot hicolor-icon-theme libatk1.0-data libglib2.0-data libgtk2.0-bin libhtml-template-perl manpages-dev notification-daemon notify-osd ssl-cert xauth xfce4-notifyd 88 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 85.8MB of archives. After unpacking 1712kB will be used. Do you want to continue? [Y/n/?] y Writing extended state information... Done Get:1 http://security.ubuntu.com/ubuntu/ lucid-updates/main libpam-modules 1.1.1-2ubuntu5 [358kB] Get:2 http://security.ubuntu.com/ubuntu/ lucid-updates/main base-files 5.0.0ubuntu20.10.04.2 [70.2kB] Get:3 http://security.ubuntu.com/ubuntu/ lucid-updates/main gzip 1.3.12-9ubuntu1.1 [102kB] Err http://security.ubuntu.com/ubuntu/ lucid-updates/main libc-bin 2.11.1-0ubuntu7.2 404 Not Found [IP: 91.189.88.37 80] Err http://security.ubuntu.com/ubuntu/ lucid-updates/main libc6 2.11.1-0ubuntu7.2 404 Not Found [IP: 91.189.88.37 80] Err http://security.ubuntu.com/ubuntu/ lucid-updates/main libc6-i686 2.11.1-0ubuntu7.2 .........

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >