Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 86/391 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

• diagnostic software for wifi adapter

  - by Nathan Fellman

  I'm having trouble with my wifi connection. Is there any software out there that can help me determine if the problem is in the drivers or in the hardware? Regretfully, I'm working on Vista Edit: The problem I'm having is that the Vista reports that the wireless radio is connected, shows an IP and all, the router also shows that the computer is connected, but there's no connectivity. I can't logon to the router, and I can't even ping it. When I ping it I get the response: General Failure I have tried connecting with and without various wireless security protocols. I have tried disabling the wireless adapter and re-enabling it from the Device Manager I have tried updating the driver None of this has helped. When I connect via Ethernet (with a cable, that is), everything works fine. Edit: I'm not using any firewall on the computer, that I'm aware of. The IP address for the WIFI adapter is similar to the one for the LAN adapter. They differ by one.

  Read the article

• Issue Connecting two home networks

  - by Alex

  Hi, I have a home networking question. I have two DLINK wireless/wired routers in my house, connected to the Internet ISP. There are a 2 computers on each of the two networks. Network1: has 192.168.0.0 (gateway) Valid IP'S range - 192.168.0.1 - 192.168.0.10, with COMP1 having a fixed IP of 162.168.0.1 Network2: has 192.168.0.100 (gateway) Valid IP'S range - 192.168.0.101 - 192.168.0.110 with COMP2 having a static IP of 162.168.0.101, a WIRELESS printer on 192.168.0.102 Both routers have a netmask of 255.255.255.0 My need is to connect the two routers, so that I can Remote desktop for COMP1 to COMP2 and viceversa, and COMP1 to connect to the wireless printer on Network2. can anyone help to set this up so that the both networks can talk to each other. Any help is appreciated. -Alex

  Read the article

• Why is my iPhone WIFI so slow at home?

  - by John Fouhy

  When my iPhone is connected to my home wireless network, the internet is unusably slow. I installed the speedtest.net application; here are some results from tonight: Down: 0.0kB/s, Up: 0.0kB/s, ping: 2230ms Down: 2.5kB/s, Up: 40.5kB/s, ping: 2182ms Down: 0.0kB/s, Up: 20.0kB/s, ping: 197ms For comparison, here is the result from my iMac to the same server, which is on the same wireless network (and has no wired connection): Down: 139kB/s, Up: 53.8kB/s, ping: 182ms Neither my iMac nor the Dell laptop also on the network have experienced the wifi problems I get with my iPhone. On the other hand, I tried browsing a website on the wireless network at work with no problems. EDIT: SpeedTest at work gives me 156kB/s down. EDIT2: Girlfriend (owner of the Dell) reports actually the internet is sometimes very slow. Perhaps there is more going on. No problems with my iMac. My router is a ASUS WL-500g Premium V2 running OpenWrt Kamikaze with X-Wrt Extensions 8.09.

  Read the article

• How to make routes on a windows 7 laptop persistent?

  - by askvictor

  I have a number of (windows 7) laptops that normally connect via wireless. We also have a wired network for special purposes. When one of these laptops plugs in to the wired network, at the moment, it makes the wired network the default route. Instead, I would like it to keep the wireless network the default, and route only 10...* through the wired. I can achieve this with: route delete 0.0.0.0 IF 22 route add 10.0.0.0 ... IF 22 (where IF 22 is the wired network interface). But how can I get this to stick? Currently, if the wired network is unplugged then re-plugged, it grabs the default route again. So I want a way of making the wireless network not get the default route, and to make the 10...* network persistent. Is there a hook to run commands after a network connection is established in windows? In linux I would use post-up hooks.

  Read the article

• ipconfig /release not working, why?

  - by barlop

  ipconfig /release is not working, why is that? here is a sequence where I put my cable in get an IP, try ipconfig /release and it tells me it can't release wireless, but there is no wireless connection. i'm just trying to release the wired one. C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Fine so I plug my cable in C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 0.0.0.0 Subnet Mask . . . . . . . . . . . : 0.0.0.0 Default Gateway . . . . . . . . . : C:\>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.1.8 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.254 Fine so from above, it clearly has an iP C:\>ipconfig /release Windows IP Configuration No operation can be performed on Wireless Network Connection while it has its me dia disconnected. C:\>

  Read the article

• Do I need a Gigabit router with a 24MB/s down and 7MB/s upload speed cable modem?

  - by djangofan

  Do I need a Gigabit port capable wireless router with a 24MB/s down and 7MB/s upload speed cable modem? Does anyone know how to calculate this? FYI, I wont be using the wireless connection from my main computer system. My computer will connect via a hard wire into the router (of the wireless variety), which in turn is connected to the cable modem. My research suggests that the 100 MB/s port can easily handle it. Is that true?

  Read the article

• Computer Loses connection to router

  - by ajon

  I have a new Windows 8 Dell XPS desktop computer at work. It has a Dell Wireless 1703 802.11 b/g/n (2.4ghz) wireless adapter. sporadically throughout the day I lose internet connectivity. When I click on the wireless system tray icon, my companies router does not appear in the list. No other computer on the network is losing connection, only this one. I don't even know what to check. Could it be an ip conflict that causes me to get booted off? (I use DHCP), but why wouldn't my computer be able to see the network. The next time it happens I will see what happens when I try to access the router directly.

  Read the article

• Ubuntu, connecting to WLAN

  - by Holly

  Hello, I successfully installed Ubuntu onto my usb hard drive. However, I'm not sure what the issue is with my internet. I'm not familiar enough with ubuntu to know whether this is a problem with recognizing my wireless card or with my internet, etc. So I suppose my question is, how do I tell whether it's recognizing my wireless card? (Network manager isn't showing any wireless signals, though I wasn't sure if it was supposed to. ) And, if it's not working, how do I go about troubleshooting that issue? Thanks!

  Read the article

• How can I make the NetworkManager work?

  - by Yang Jy

  I am running a version of RHCE6 on my laptop, and lately I've been trying various stuff about network configuration through command line. Last night, I tried removing the NetworkManager using "yum remove NetworkManager" from the system, so that I could have more control of the network through the command line. But the result is, I didn't manage to configure the wireless connection through wpa_supplicant, and I need wireless connection during my travel to another place. So I need the wireless function back as soon as possible. I typed " yum install NetworkManager", some version installed, but I don't get to have an icon on the taskbar, and of course, the network doesn't work. The package I previously removed(about 24MB) was much larger that the one I just installed(about 2MB), so I think some dependencies must be missing. How could I install all these dependencies? Please help!

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

• routing problems

  - by user174050

  I have an windows 7 laptop and I have installed openvpn 2.2x as client. The laptop has 2 ethernet cards, one of them is wireless. The wireless lan is 192.168.1.0/24 The Fix lan is 192.168.2.0/24 If I connect to the openvpn server useing the Fix lan the I can connect properly and for testing I ping to my openvpn server 10.0.0.1 that answers correctly. But if I connect to the openvpn server useing the wireless lan, I can establish the connection but pinging to the server isn´t possible. The packets goes allways lost. Why can this happen? In an other laptop where windows xp is installed and with the same lan configuratio everything works propperly. In both cases the firewall is configured to access the vnc server and the server directories useing samba. With the XP I have no problems. I will thank you for all help Ignacio

  Read the article

• Losing WLAN connections but maintaining internet connections on WIndows 7 Workgroup

  - by Di

  I have 4 computers all running Windows 7 networked in a Work group through Billion 7404vgp-m wireless router. All drivers and firmware for wireless adapters and router are up to date. Windows Firewall and Defender disabled. Disconnected ipv6. Running Nod 32 anti virus software. All have own static IP address 192.XXX.X.XXX. When I Reset the router all computers have Internet and LAN access for about 1 hour and then they will lose the LAN connection but maintain Internet connection. Resetting wireless adapters or restarting computers does nothing to fix this but resetting router will. What is causing this? How do I fix it?

  Read the article

• Ubuntu: On a network with many clients there are two machines that can't access the web via a browser at the same time

  - by ChrisInCambo

  Ok I'm pulling my hair out over this one. We have a wireless network with many clients all working well except two Ubuntu clients running 10.10 that can't access the internet via a browser at the same time. They can both still ping, use Skype etc but can't browse. As soon as the one that can browse exits the network browsing returns for the other and vice versa. As ping and Skype was working I assumed some kind of DNS problem but moving over to OpenDNS didn't solve it, nor did restarting networking or using wired rather than wireless. We also switched out the router, and it still persisted so I'm sure this isn't a network issue. The two clients are both laptops and work fine together on a wireless network at another office (which we don't control). I'm thinking something must be cached from the other network they both use that's causing this but have no idea what. Does anyone have any ideas? I just don't know where to go from here.

  Read the article

• list and explanations of ways to boost this router's signal strength? [closed]

  - by barlop

  Possible Duplicates: Improve Wireless Signal How to get wireless coverage over my whole house? What's the best way to increase the range of my 802.11g router? The back of my house doesn't have WiFi Signal I'm interested in ways that are both specific to certain routers, and generic. When I say generic, I don't necessarily mean a one way that works for many.. but it can also be a generic answer, so mentioning solutions for different situations. So not just the one router I mention. Explanations are important, as well as all the ways. One i'm particularly interested in boosting the strength of is this wireless router/modem Netgear VMDG280 maybe anywhere in a big house with three floors, maybe from the garden.

  Read the article

• Internet Connectivity... Help please!

  - by James

  Hi. My Laptop is having trouble connecting to my wireless router. Other laptops are using the wireless, but it's not reached capacity. The laptop recognises (with a strong signal) that there is wireless internet, and I can connect via the router with a cable because this happens automatically. My problem is this... When I click "connect" (for example in the network and sharing centre), the dialogue box closes and nothing else happens - as though "connect" is being read as "exit". I am running Vista on a Toshiba Satellite Pro P300. Any help would be very much appreciated, Thanks

  Read the article

• Can one use Airport (Time Capsule) with an external DHCP server?

  - by DNS

  I currently share my DSL connection using a wireless router with DHCP disabled, and dnsmasq running on a Mac Mini serving DHCP & DNS. This setup is important because I have clients doing PXE boot, and I need the control over DHCP that dnsmasq provides. There is also a Time Capsule on the network that's used purely as a backup device; its wireless functions are disabled. The wireless router is starting to get a little flaky, and since it doesn't support 802.11n I'd like to replace it. Rather than buying a new router, I'd like to just use the Time Capsule. But I see no way to disable its DHCP server; when I set the connection type to PPPoE, it insists on serving DHCP. Is there any way to use Airport PPPoE with a DHCP server elsewhere on the network?

  Read the article

• unable to ping machine on WLAN

  - by N.M.

  I've started accepting remote desktop connections on one of my machines. If i connect the machine to my router using an Ethernet cable i am able to ping it and connect to it remotely (using RDP). However, if i connect the machine using wireless network i am unable to ping it (or access it using RDP). Although i can live with connecting that machine using an Ethernet cable i just wanted to know the reason why it doesn't work using wireless. Is the router not able to forward packets to that host if its connected using wireless? If yes, any solutions?

  Read the article

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

• How did Ubuntu know my WPA Key?

  - by nebukadnezzar

  I've recently moved my /home to another computer (keeping all configuration files), with a fresh installation of Ubuntu 10.10. After Installation I've installed wicd and ndiswrapper, to get my Internet Connection up and running. However, after changing /etc/network/interfaces from auto lo iface lo inet loopback To auto wlan0 iface wlan0 inet dhcp and running sudo /etc/init.d/networking restart to get wlan0 set up, wicd just suddenly connected... to my modem. Without supplying any information about the modem whatsoever. Of course wicd creates a local directory at ~/.wicd/, but that directory is empty, and the temporary global configuration at /var/lib/wicd/configurations/ didn't exist due to fresh installation of ubuntu. So what's the deal? Where did wicd get the ESSID and the WPA Key? There hasn't been any activity in this question, but it's still open (and even worth some rep)!

  Read the article

• Wifi function key not working on HP laptop

  - by lopsided98

  I have an HP Pavilion g7-1260 with Ubuntu 13.10 on it. I would like to be able to use the wifi toggle key on the keyboard to enable and disable wifi. My wifi works fine and the light on the key turns on when I enable wifi through the Ubuntu networking menu. The problem is that pressing the key does not do anything. It should be activated when I press fn + f12. I tried using xev to see if an event was generated but there wasn't one. I also tried the same thing with apci_listen but it didn't output anything. Does anyone know how to get the key to work?

  Read the article

• Dell 3721 Wifi problem Ubuntu 13.04

  - by Sebastian

  I have a Dell 3721 which comes original with windows 8. I managed it to install ubuntu 12.10 on this laptop, even there was no out of the box drivers. With 12.10 I was forces to install this .deb package couple of times. After installing it, it was ok for some weeks before I have to install it again. Maybe some security updates destroy something which made in necessary to install it again... http://jas.gemnetworks.com/debian/pool/main/w/wireless-bcm43142/wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb My problem is, that this package isnt working with ubuntu 13.04 anymore. So I cant use Wifi now. Also my display is almost dark, I cant change the brightness level with ubuntu 13.04. Hope you can give me some advice. Dell:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) @Dell:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0a5c:21d7 Broadcom Corp. Bus 001 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0c45:64ad Microdia @Dell:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) @Dell:~$ sudo lshw -class network *-network Beschreibung: Ethernet interface Produkt: RTL8101E/RTL8102E PCI Express Fast Ethernet controller Hersteller: Realtek Semiconductor Co., Ltd. Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Logischer Name: eth0 Version: 05 Seriennummer: xx:xx:xx:xx:xx:xx Größe: 100Mbit/s Kapazität: 100Mbit/s Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation Konfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.103 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s Ressourcen: irq:42 ioport:2000(Größe=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network UNGEFORDERT Beschreibung: Network controller Produkt: BCM43142 802.11b/g/n Hersteller: Broadcom Corporation Physische ID: 0 Bus-Informationen: pci@0000:02:00.0 Version: 01 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress bus_master cap_list Konfiguration: latency=0 Ressourcen: memory:c0500000-c0507fff

  Read the article

• Getting wifi working on 14.04

  - by user286114

  I have installed Ubuntu 14.04 on my laptop. When I plug in the ethernet cable the internet works fine, but I can't see any wireless network in the networking manager. The wifi switch is definitely on on my laptop! It's a Dell XPS M1330. I'm not sure what the network card is - how can I find out? nm-tool gives me this: NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: tg3 State: connected Default: yes HW Address: 00:23:AE:28:FE:A2 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.26 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.254 DNS: 192.168.1.254

  Read the article

• Wifi Direct P2P-go and P2P-client support in ubuntu

  - by giri

  I am trying to get wifi direct working on a laptop with ubuntu 12.04 When I type the command 'iw list' it doesn't show P2P-client or P2P-go under 'supported interface modes.From http://wireless.kernel.org/en/users/Documentation/iw/replace-iwconfig I found that 'iwconfig' was replaced with 'iw'.Does it mean that my hardware doesn't have support for wifi-direct or is it just the software(drivers) issue? If is it just sofware issue please help me to find the right drivers which support wifi-direct. Here is the info about my ethernet controller from the output of 'lspci' 02:00.0 Ethernet controller: Atheros Communication Inc. AR242x / AR542x Wreless Network Adapter (PCI-Express) (rev 01) 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 13)

  Read the article

• How can I get a Belkin N600 DB (F9L1101v1) to work on Ubuntu 12,04 64-Bit

  - by rheide

  I could use some assistance to trying to get a Belkin N600 DB Wireless Dual-Band USB Adapter to work on a Dell Inspiron 1525 with 64-Bit Ubuntu 12.04. The device won't work out of the box. Tried to go the NDISWrapper route, but using the GUI, received the following message: Module could not be loaded. Error was: FATAL: Module ndiswrapper not found. Is the ndiswrapper module installed? Despite the fact that it showed up listed in the GUI, the device still did not function properly. How should I proceed from here?

  Read the article

• wpa_supplicant ioctl[SIOCSIWENCODEEXT]: Invalid argument

  - by RobinJ

  I just installed Ubuntu Server on a spare computer with a broken graphic card, and I needed to setup my wifi. I thought No problem, I've done it before from the command line, in Arch Linux., only the steps I had to take in Arch Linux didn't work in Ubuntu Server (that's odd, wasn't Ubuntu supposed to be so much more user-friendly? :/). This is what I'd normally do: ip link set wlan0 up wpa_passphrase <ESSID> <WPA KEY> > /etc/wpa_supplicant.conf wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 Only at the wpa_supplicant I get some strane message: ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument And if I try to run dhcpcd then (which I manually installed, as it didn't come preinstalled with Ubuntu Server), it times out. Help on how to do it would be much appreciated. My wireless driver is iwl3945.

  Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >