Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 90/391 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• L2TP connection fails!

  - by a.toraby

  I've installed l2tp-ipsec-vpn but when I try to connect to the vpn server I get error 500. Here are the logs: Jun 17 12:54:37.449 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:54:38.858 Stopping xl2tpd: xl2tpd. Jun 17 12:54:38.859 xl2tpd[1511]: death_handler: Fatal signal 15 received Jun 17 12:54:38.872 ipsec_setup: Starting Openswan IPsec U2.6.37/K3.2.0-23-generic... Jun 17 12:54:39.027 ipsec__plutorun: Starting Pluto subsystem... Jun 17 12:54:39.033 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Jun 17 12:54:39.037 recvref[30]: Protocol not available Jun 17 12:54:39.038 xl2tpd[2442]: This binary does not support kernel L2TP. Jun 17 12:54:39.038 xl2tpd[2444]: xl2tpd version xl2tpd-1.3.1 started on atp-ThinkPad-SL410 PID:2444 Jun 17 12:54:39.038 xl2tpd[2444]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. Jun 17 12:54:39.038 xl2tpd[2444]: Forked by Scott Balmos and David Stipp, (C) 2001 Jun 17 12:54:39.038 xl2tpd[2444]: Inherited by Jeff McAdams, (C) 2002 Jun 17 12:54:39.039 xl2tpd[2444]: Forked again by Xelerance (www.xelerance.com) (C) 2006 Jun 17 12:54:39.039 xl2tpd[2444]: Listening on IP address 0.0.0.0, port 1701 Jun 17 12:54:39.040 Starting xl2tpd: xl2tpd. Jun 17 12:54:39.062 ipsec__plutorun: 002 added connection description "L2TP" Jun 17 12:55:30.753 104 "L2TP" #1: STATE_MAIN_I1: initiate Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 20s for response Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 40s for response Jun 17 12:55:30.754 003 "L2TP" #1: ignoring Vendor ID payload [MS NT5 ISAKMPOAKLEY 00000008] Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [RFC 3947] method set to=109 Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 109 Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [FRAGMENTATION] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [MS-Negotiation Discovery Capable] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [IKE CGA version 1] Jun 17 12:55:30.755 106 "L2TP" #1: STATE_MAIN_I2: sent MI2, expecting MR2 Jun 17 12:55:30.755 010 "L2TP" #1: STATE_MAIN_I2: retransmission; will wait 20s for response Jun 17 12:55:30.755 003 "L2TP" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed Jun 17 12:55:30.755 108 "L2TP" #1: STATE_MAIN_I3: sent MI3, expecting MR3 Jun 17 12:55:30.756 004 "L2TP" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Jun 17 12:55:30.756 117 "L2TP" #2: STATE_QUICK_I1: initiate Jun 17 12:55:30.756 010 "L2TP" #2: STATE_QUICK_I1: retransmission; will wait 20s for response Jun 17 12:55:30.756 003 "L2TP" #2: ignoring informational payload, type IPSEC_RESPONDER_LIFETIME msgid=6b03ff69 Jun 17 12:55:30.756 003 "L2TP" #2: NAT-Traversal: received 2 NAT-OA. ignored because peer is not NATed Jun 17 12:55:30.756 003 "L2TP" #2: our client subnet returned doesn't match my proposal - us:192.168.1.3/32 vs them:109.162.174.235/32 Jun 17 12:55:30.757 003 "L2TP" #2: Allowing questionable proposal anyway [ALLOW_MICROSOFT_BAD_PROPOSAL] Jun 17 12:55:30.757 004 "L2TP" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x23af21f8 <0xdb4a87b6 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} Jun 17 12:55:31.759 xl2tpd[2444]: Connecting to host x.x.x.x, port 1701 Jun 17 12:55:32.021 xl2tpd[2444]: Connection established to x.x.x.x, 1701. Local: 4720, Remote: 200 (ref=0/0). Jun 17 12:55:32.023 xl2tpd[2444]: Calling on tunnel 4720 Jun 17 12:55:32.454 xl2tpd[2444]: Call established with x.x.x.x, Local: 9667, Remote: 3, Serial: 1 (ref=0/0) Jun 17 12:55:32.456 xl2tpd[2444]: start_pppd: I'm running: Jun 17 12:55:32.456 xl2tpd[2444]: "/usr/sbin/pppd" Jun 17 12:55:32.457 xl2tpd[2444]: "passive" Jun 17 12:55:32.458 xl2tpd[2444]: "nodetach" Jun 17 12:55:32.458 xl2tpd[2444]: ":" Jun 17 12:55:32.459 xl2tpd[2444]: "file" Jun 17 12:55:32.459 xl2tpd[2444]: "/etc/ppp/L2TP.options.xl2tpd" Jun 17 12:55:32.460 xl2tpd[2444]: "ipparam" Jun 17 12:55:32.461 xl2tpd[2444]: "x.x.x.x" Jun 17 12:55:32.462 xl2tpd[2444]: "/dev/pts/1" Jun 17 12:55:32.583 pppd[2711]: Plugin passprompt.so loaded. Jun 17 12:55:32.583 pppd[2711]: pppd 2.4.5 started by root, uid 0 Jun 17 12:55:32.619 pppd[2711]: Using interface ppp0 Jun 17 12:55:32.620 pppd[2711]: Connect: ppp0 <--> /dev/pts/1 Jun 17 12:55:33.693 pppd[2711]: /usr/bin/L2tpIPsecVpn exited with code 0 Jun 17 12:55:34.454 [ERROR 404] Authentication failed: closing connection to 'L2TP' Jun 17 12:55:34.456 pppd[2711]: MS-CHAP authentication failed: E=691 Authentication failure Jun 17 12:55:34.457 pppd[2711]: CHAP authentication failed Jun 17 12:55:34.461 Stopping xl2tpd: xl2tpd. Jun 17 12:55:34.462 xl2tpd[2444]: death_handler: Fatal signal 15 received Jun 17 12:55:34.463 pppd[2711]: Modem hangup Jun 17 12:55:34.463 pppd[2711]: Connection terminated. Jun 17 12:55:34.474 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:55:34.482 pppd[2711]: Exit. Jun 17 12:55:35.587 ipsec_setup: ERROR: Module xfrm4_mode_transport is in use Jun 17 12:55:35.665 ipsec_setup: ERROR: Module esp4 is in use I had this problem by ubuntu 11.10 though I can easily connect to the server from windows. I use ubuntu 12.0 64bit

  Read the article

• Redirect network logs from syslog to another file

  - by w0rldart

  I keep logging way to much info (not needed, for now) in my syslog, and not daily or hourly... but instant. If I want to watch for something in my syslog I just can't because the network log keeps interfering. So, how can I redirect network logs to another file and/or stop logging it? Dec 10 17:01:33 user kernel: [ 8716.000587] MediaState is connected Dec 10 17:01:33 user kernel: [ 8716.000599] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:33 user kernel: [ 8716.000601] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:33 user kernel: [ 8716.000612] rt28xx_get_wireless_stats ---> Dec 10 17:01:33 user kernel: [ 8716.000615] <--- rt28xx_get_wireless_stats Dec 10 17:01:39 user kernel: [ 8722.000714] MediaState is connected Dec 10 17:01:39 user kernel: [ 8722.000729] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:39 user kernel: [ 8722.000732] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:39 user kernel: [ 8722.000747] rt28xx_get_wireless_stats ---> Dec 10 17:01:39 user kernel: [ 8722.000751] <--- rt28xx_get_wireless_stats Dec 10 17:01:44 user kernel: [ 8726.904025] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:01:45 user kernel: [ 8728.003138] MediaState is connected Dec 10 17:01:45 user kernel: [ 8728.003153] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:45 user kernel: [ 8728.003157] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:45 user kernel: [ 8728.003171] rt28xx_get_wireless_stats ---> Dec 10 17:01:45 user kernel: [ 8728.003175] <--- rt28xx_get_wireless_stats Dec 10 17:01:51 user kernel: [ 8734.004066] MediaState is connected Dec 10 17:01:51 user kernel: [ 8734.004079] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:51 user kernel: [ 8734.004082] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:51 user kernel: [ 8734.004096] rt28xx_get_wireless_stats ---> Dec 10 17:01:51 user kernel: [ 8734.004099] <--- rt28xx_get_wireless_stats Dec 10 17:01:57 user kernel: [ 8740.004108] MediaState is connected Dec 10 17:01:57 user kernel: [ 8740.004119] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:01:57 user kernel: [ 8740.004121] ==>rt_ioctl_giwfreq 11 Dec 10 17:01:57 user kernel: [ 8740.004132] rt28xx_get_wireless_stats ---> Dec 10 17:01:57 user kernel: [ 8740.004135] <--- rt28xx_get_wireless_stats Dec 10 17:01:57 user kernel: [ 8740.436021] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:03 user kernel: [ 8746.005280] MediaState is connected Dec 10 17:02:03 user kernel: [ 8746.005294] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:03 user kernel: [ 8746.005298] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:03 user kernel: [ 8746.005312] rt28xx_get_wireless_stats ---> Dec 10 17:02:03 user kernel: [ 8746.005315] <--- rt28xx_get_wireless_stats Dec 10 17:02:09 user kernel: [ 8752.004790] MediaState is connected Dec 10 17:02:09 user kernel: [ 8752.004804] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:09 user kernel: [ 8752.004808] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:09 user kernel: [ 8752.004821] rt28xx_get_wireless_stats ---> Dec 10 17:02:09 user kernel: [ 8752.004825] <--- rt28xx_get_wireless_stats Dec 10 17:02:15 user kernel: [ 8757.984031] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:15 user kernel: [ 8758.004078] MediaState is connected Dec 10 17:02:15 user kernel: [ 8758.004094] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:15 user kernel: [ 8758.004097] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:15 user kernel: [ 8758.004112] rt28xx_get_wireless_stats ---> Dec 10 17:02:15 user kernel: [ 8758.004116] <--- rt28xx_get_wireless_stats Dec 10 17:02:16 user kernel: [ 8759.492017] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:19 user kernel: [ 8762.002179] SCANNING, suspend MSDU transmission ... Dec 10 17:02:19 user kernel: [ 8762.004291] MlmeScanReqAction -- Send PSM Data frame for off channel RM, SCAN_IN_PROGRESS=1! Dec 10 17:02:19 user kernel: [ 8762.025055] SYNC - BBP R4 to 20MHz.l Dec 10 17:02:19 user kernel: [ 8762.027249] RT35xx: SwitchChannel#1(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF1, K=0x02, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.170206] RT35xx: SwitchChannel#2(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF1, K=0x07, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.318211] RT35xx: SwitchChannel#3(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF2, K=0x02, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.462269] RT35xx: SwitchChannel#4(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF2, K=0x07, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.606229] RT35xx: SwitchChannel#5(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF3, K=0x02, R=0x02 Dec 10 17:02:19 user kernel: [ 8762.750202] RT35xx: SwitchChannel#6(RF=8, Pwr0=30, Pwr1=25, 2T), N=0xF3, K=0x07, R=0x02 Dec 10 17:02:20 user kernel: [ 8762.894217] RT35xx: SwitchChannel#7(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF4, K=0x02, R=0x02 Dec 10 17:02:20 user kernel: [ 8763.038202] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:20 user kernel: [ 8763.040194] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:20 user kernel: [ 8763.040199] BAR(1) : Tid (0) - 03a3:037e Dec 10 17:02:20 user kernel: [ 8763.040387] SYNC - End of SCAN, restore to channel 11, Total BSS[03] Dec 10 17:02:20 user kernel: [ 8763.040400] ScanNextChannel -- Send PSM Data frame Dec 10 17:02:20 user kernel: [ 8763.040402] bFastRoamingScan ~~~~~~~~~~~~~ Get back to send data ~~~~~~~~~~~~~ Dec 10 17:02:20 user kernel: [ 8763.040405] SCAN done, resume MSDU transmission ... Dec 10 17:02:20 user kernel: [ 8763.047022] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:20 user kernel: [ 8763.047026] BAR(1) : Tid (0) - 03a3:03a5 Dec 10 17:02:21 user kernel: [ 8763.898130] bImprovedScan ............. Resume for bImprovedScan, SCAN_PENDING .............. Dec 10 17:02:21 user kernel: [ 8763.898143] SCANNING, suspend MSDU transmission ... Dec 10 17:02:21 user kernel: [ 8763.900245] MlmeScanReqAction -- Send PSM Data frame for off channel RM, SCAN_IN_PROGRESS=1! Dec 10 17:02:21 user kernel: [ 8763.921144] SYNC - BBP R4 to 20MHz.l Dec 10 17:02:21 user kernel: [ 8763.923339] RT35xx: SwitchChannel#8(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF4, K=0x07, R=0x02 Dec 10 17:02:21 user kernel: [ 8763.996019] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:21 user kernel: [ 8764.066221] RT35xx: SwitchChannel#9(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF5, K=0x02, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.210212] RT35xx: SwitchChannel#10(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF5, K=0x07, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.215536] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.215542] BAR(1) : Tid (0) - 0457:0452 Dec 10 17:02:21 user kernel: [ 8764.244000] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.244004] BAR(1) : Tid (0) - 0459:0456 Dec 10 17:02:21 user kernel: [ 8764.253019] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.253023] BAR(1) : Tid (0) - 045c:0458 Dec 10 17:02:21 user kernel: [ 8764.256677] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.256681] BAR(1) : Tid (0) - 045c:045b Dec 10 17:02:21 user kernel: [ 8764.259785] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.259788] BAR(1) : Tid (0) - 045d:045b Dec 10 17:02:21 user kernel: [ 8764.280467] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.280471] BAR(1) : Tid (0) - 045f:045c Dec 10 17:02:21 user kernel: [ 8764.282189] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:21 user kernel: [ 8764.282192] BAR(1) : Tid (0) - 045f:045e Dec 10 17:02:21 user kernel: [ 8764.354204] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.356408] ScanNextChannel():Send PWA NullData frame to notify the associated AP! Dec 10 17:02:21 user kernel: [ 8764.498202] RT35xx: SwitchChannel#12(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x07, R=0x02 Dec 10 17:02:21 user kernel: [ 8764.642210] RT35xx: SwitchChannel#13(RF=8, Pwr0=30, Pwr1=28, 2T), N=0xF7, K=0x02, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.790229] RT35xx: SwitchChannel#14(RF=8, Pwr0=30, Pwr1=28, 2T), N=0xF8, K=0x04, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.934238] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.935243] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:22 user kernel: [ 8764.935249] BAR(1) : Tid (0) - 048e:0485 Dec 10 17:02:22 user kernel: [ 8764.936423] SYNC - End of SCAN, restore to channel 11, Total BSS[05] Dec 10 17:02:22 user kernel: [ 8764.936436] ScanNextChannel -- Send PSM Data frame Dec 10 17:02:22 user kernel: [ 8764.936440] SCAN done, resume MSDU transmission ... Dec 10 17:02:22 user kernel: [ 8764.940529] RT35xx: SwitchChannel#11(RF=8, Pwr0=29, Pwr1=26, 2T), N=0xF6, K=0x02, R=0x02 Dec 10 17:02:22 user kernel: [ 8764.942178] CntlEnqueueForRecv(): BAR-Wcid(1), Tid (0) Dec 10 17:02:22 user kernel: [ 8764.942182] BAR(1) : Tid (0) - 0493:048e Dec 10 17:02:22 user kernel: [ 8764.942715] CNTL - All roaming failed, restore to channel 11, Total BSS[05] Dec 10 17:02:22 user kernel: [ 8764.948016] MMCHK - No BEACON. restore R66 to the low bound(56) Dec 10 17:02:22 user kernel: [ 8764.948307] ===>rt_ioctl_giwscan. 5(5) BSS returned, data->length = 1111 Dec 10 17:02:23 user kernel: [ 8766.048073] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:23 user kernel: [ 8766.552034] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:27 user kernel: [ 8770.001180] MediaState is connected Dec 10 17:02:27 user kernel: [ 8770.001197] ==>rt_ioctl_giwmode(mode=2) Dec 10 17:02:27 user kernel: [ 8770.001201] ==>rt_ioctl_giwfreq 11 Dec 10 17:02:27 user kernel: [ 8770.001219] rt28xx_get_wireless_stats ---> Dec 10 17:02:27 user kernel: [ 8770.001223] <--- rt28xx_get_wireless_stats Dec 10 17:02:28 user kernel: [ 8771.564020] QuickDRS: TxTotalCnt <= 15, train back to original rate Dec 10 17:02:29 user kernel: [ 8772.064031] QuickDRS: TxTotalCnt <= 15, train back to original rate

  Read the article

• VBox Failed to open/create the internal network after upgrading to ubuntu 13.10

  - by stefmex

  Every thing was perfect I have 2 guest Virtual machines (ubuntu server 12.04 and Win 7) on ubuntu 13.04 but after upgrading host to 13.10 I can't start them with bridged network adaptator.... Failed to open/create the internal network 'HostInterfaceNetworking-wlan0' (VERR_INTNET_FLT_IF_NOT_FOUND). Failed to attach the network LUN (VERR_INTNET_FLT_IF_NOT_FOUND). Código Resultado: NS_ERROR_FAILURE (0x80004005) Componente: Console Interfaz: IConsole {db7ab4ca-2a3f-4183-9243-c1208da92392} Vbox 4.2.12 May you help me ?

  Read the article

• Samba folder is gone

  - by bioShark

  I seem to have some issues sharing folders from my Ubuntu 12.04 machine to a Win7 machine. After playing around with the settings, I decided to revert to Samba's original setting by reinstalling it: sudo apt-get purge samba sudo rm -rf /etc/samba/ /etc/default/samba sudo apt-get install samba just to be sure I also run: sudo apt-get install samba samba-common system-config-samba winbind Now, I can't find /etc/samba folder any more. Even when I try to share a folder through Nautilus, I get: Samba's testparm returned error 1: Load smb config files from /etc/samba/smb.conf rlimit_max: increasing rlimit_max (1024) to minimum Windows limit (16384) params.c:OpenConfFile() - Unable to open configuration file "/etc/samba/smb.conf": No such file or directory Error loading services. Same when I try to list: xxx@xxx:~$ ll /etc/samba ls: cannot access /etc/samba: No such file or directory Any ideas what I did wrong, or what other package am I missing? cheers

  Read the article

• How to map network scanner

  - by Andrew Heath

  I have just bought a shiny new Canon MG6250 multifunction printer/scanner and connected it via LAN. Installing the printing side of things was a breeze, however, I cannot work out how to set up scanning. I installed the MG6200 series ScanGear MP driver from Canon's site but when I open GIMP or Simple Scan, they say there is no scanner detected. Using GIMP's 'update scanner list' button to search for the scanner does not find it. How do I tell Ubuntu, GIMP or Simple Scan to look on the network for the scanner? Is there another utility especially for this?

  Read the article

• RockMelt – Browsing Experience Re-Imagined.

  - by Damodhar

  RockMelt is a social web browser built off of Chromium and boasts deep integration with both Facebook and Twitter with it’s “Edges” which are filled with friends which are online. RockMelt gives you greater power to add friends to your Facebook account and chat with those online. It is backed by Netscape founder Marc Andreessen. RockMelt – Introduction RockMelt does more than just navigate Web pages. It makes it easy for you to do the things you do every single day on the Web: share and keep up with your friends, stay up-to-date on news and information, and search Connect For An Invitation To participate, you must connect via Facebook from RockMelt homepage and then wait for your invitation. Alternatively, try the link below and see if you could download RockMelt: Download RockMelt This article titled,RockMelt – Browsing Experience Re-Imagined., was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• Error during update 'Unable to connect to 192.168.43.1:8000'

  - by Alex R

  When I tried to update my Ubuntu through the update manager I received an error about some unknown resource. so i tried doing it from the terminal with sudo apt-get update but all I got is: 0% [Connecting to 192.168.43.1 repeating itself... and when I press Enter it shows: W: Failed to fetch http://archive.ubuntu.com/ubuntu/dists/precise-security/universe/i18n/Translation-en Unable to connect to 192.168.43.1:8000: E: Some index files failed to download. They have been ignored, or old ones used instead. How can I get this to work?

  Read the article

• Highly available iSCSI target

  - by sysetr

  I'm in the process of setting up iSCSI target on DRBD following the steps detailed here. I would appreciate if someone can answer and explain the following queries: Is there a way to set up just 1 resource for iscsi config and storage? Why does iscsi.config have to have a separate resource (in drbd.conf). Is it possible to put iscsi.config and iscsi.target in one disk? If not possible, what would be a good ratio (space wise) for iscsi.config and iscsi.target? Assuming I need to set up a 1TB iscsi.storage, how much space should I allocate for iscsi.config?

  Read the article

• 12.04 on VirtualBox -No internet access on Guest OS

  - by Muzab

  I have Windows 7 as my Host OS which has wired Ethernet working. My guest OS on VirtualBox is Ubuntu 12.04. The problem is that I cannot browse. I have: Enabled sharing on Windows; Have used NAT, Bridged Adapter etc ( all possible combinations); With NAT, used PCnet-FAST II (Am79c973) combination. Ubuntu says "connected to wired ethernet1" but I cannot access websites. VirtualBox Host-Only Network in the Network and Sharing center shows that I don't have IPV4 and IPV6 connectivity. Meaning I don't have DHCP configured. Strangely I have DNS address correct in the Ubuntu properties.

  Read the article

• Start Developing a Multiplayer Online Client to host existing video game

  - by Rami.Shareef

  GameRanger Garena ... etc I'm planning to start developing a small online client like these mentioned above (for friends usage), where the player that hosts the game is the server him self. was looking through the web for something to start with, but couldnt find any resources for this request!. Planning to do it with .NET technology, I have a good decent development experience. Any good resources to start with? the game I'm aiming to support is WarCraft III The frozen throne as start

  Read the article

• Minidlna Directory Issues

  - by Somnambulist

  I've done my searching and can't find an answer to THIS specific issue. I have my minidlna set up and running - but it's not really done properly. First off, when I open the server on my bluray player, all of my movies are listed twice - when they are certainly not saved on my external twice. Second, when I open the server - rather than reading "Movies" "TV" "Music", etc - It just mashes all of my movies, tv, and some other folders all together with no real organization. I never had this problem when I had my Windows set up, so I know it's something configured improperly more-so than my external drive giving me gruff. Here's my minidlna.conf file: # This is the configuration file for the MiniDLNA daemon, a DLNA/UPnP-AV media # server. # # Unless otherwise noted, the commented out options show their default value. # # On Debian, you can also refer to the minidlna.conf(5) man page for # documentation about this file. media_dir=/media/somnambulist/Ghost In You # This option can be specified more than once if you want multiple directories # scanned. # # If you want to restrict a media_dir to a specific content type, you can # prepend the directory name with a letter representing the type (A, P or V), # followed by a comma, as so: # * "A" for audio (eg. media_dir=A,/var/lib/minidlna/music) # * "P" for pictures (eg. media_dir=P,/var/lib/minidlna/pictures) # * "V" for video (eg. media_dir=V,/var/lib/minidlna/videos) # # WARNING: After changing this option, you need to rebuild the database. Either # run minidlna with the '-R' option, or delete the 'files.db' file # from the db_dir directory (see below). # On Debian, you can run, as root, 'service minidlna force-reload' instead. #media_dir=/var/lib/minidlna media_dir=V,/media/somnambulist/Ghost In You/Movies media_dir=V,/media/somnambulist/Ghost In You/TV media_dir=P,/home/somnambulist/Pictures # Path to the directory that should hold the database and album art cache. db_dir=/home/somnambulist/serverart # Path to the directory that should hold the log file. log_dir=/home/somnambulist/serverlog # Minimum level of importance of messages to be logged. # Must be one of "off", "fatal", "error", "warn", "info" or "debug". # "off" turns of logging entirely, "fatal" is the highest level of importance # and "debug" the lowest. #log_level=warn # Use a different container as the root of the directory tree presented to # clients. The possible values are: # * "." - standard container # * "B" - "Browse Directory" # * "M" - "Music" # * "P" - "Pictures" # * "V" - "Video" # if you specify "B" and client device is audio-only then "Music/Folders" will be used as root root_container=B # Network interface(s) to bind to (e.g. eth0), comma delimited. #network_interface= # IPv4 address to listen on (e.g. 192.0.2.1). #listening_ip= # Port number for HTTP traffic (descriptions, SOAP, media transfer). port=8200 # URL presented to clients. # The default is the IP address of the server on port 80. #presentation_url=http://example.com:80 # Name that the DLNA server presents to clients. friendly_name=Somnambulist Media Server # Serial number the server reports to clients. serial=12345678 # Model name the server reports to clients. #model_name=Windows Media Connect compatible (MiniDLNA) # Model number the server reports to clients. model_number=1 # Automatic discovery of new files in the media_dir directory. #inotify=yes # List of file names to look for when searching for album art. Names should be # delimited with a forward slash ("/"). album_art_names=Cover.jpg/cover.jpg/AlbumArtSmall.jpg/albumartsmall.jpg/AlbumArt.jpg/albumart.jpg/Album.jpg/album.jpg/Folder.jpg/folder.jpg/Thumb.jpg/thumb.jpg # Strictly adhere to DLNA standards. # This allows server-side downscaling of very large JPEG images, which may # decrease JPEG serving performance on (at least) Sony DLNA products. #strict_dlna=no # Support for streaming .jpg and .mp3 files to a TiVo supporting HMO. #enable_tivo=no # Notify interval, in seconds. #notify_interval=895 # Path to the MiniSSDPd socket, for MiniSSDPd support. #minissdpdsocket=/run/minissdpd.sock` And here's the error I get in terminal when I run: sudo service minidlna restart sudo service minidlna force-reload Force restart error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:27] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] Force-reload error: Restarting DLNA/UPnP-AV media server minidlna [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/Movies" not accessible! [Permission denied] [2013/08/12 21:19:46] minidlna.c:474: error: Media directory "/media/somnambulist/Ghost In You/TV" not accessible! [Permission denied] rm: cannot remove ‘/home/somnambulist/serverart/files.db’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Slumdog Millionaire/Slumdog.Millionaire.Cover.jpg’: Permission denied rm: cannot remove ‘/home/somnambulist/serverart/art_cache/media/somnambulist/Ghost In You/Movies/Zack and Miri Make a Porno/ZackAndMiriMakeAPornoCover.jpg’: Permission denied [2013/08/12 21:19:46] minidlna.c:744: warn: Failed to clean old file cache. [ OK ] I've spent hours on this at this point, read through various files - and even had a friend who is relatively Ubuntu-savvy try to help me via chat - no such luck. Thanks in advance for any help.

  Read the article

• Frequent Disconnects ubuntu desktop 12.10 x64 intel 82579V e1000e

  - by user112055

  I'm having frequent disconnects with my new install of Ubuntu 12.10. I tried updating the kernel driver to the latest intel release to no avail. My expertise is spent. It happens anywhere between 1 min and 10 min. Any ideas? syslog: Dec 1 13:51:39 andromeda kernel: [ 972.188809] audit_printk_skb: 6 callbacks suppressed Dec 1 13:51:39 andromeda kernel: [ 972.188813] type=1701 audit(1354398699.418:199): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188817] type=1701 audit(1354398699.418:200): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188820] type=1701 audit(1354398699.418:201): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188823] type=1701 audit(1354398699.418:202): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.188825] type=1701 audit(1354398699.418:203): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=4 compat=0 ip=0x7f26777d9205 code=0x50000 Dec 1 13:51:39 andromeda kernel: [ 972.331419] type=1701 audit(1354398699.558:204): auid=4294967295 uid=1000 gid=1000 ses=4294967295 pid=6039 comm="chrome" reason="seccomp" sig=0 syscall=2 compat=0 ip=0x7f26777d96b0 code=0x50000 Dec 1 13:53:12 andromeda NetworkManager[1115]: <info> (eth0): carrier now OFF (device state 100, deferring action for 4 seconds) Dec 1 13:53:12 andromeda kernel: [ 1064.894387] e1000e: e1000e: eth0 NIC Link is Down Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): device state change: activated -> unavailable (reason 'carrier-changed') [100 20 40] Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): deactivating device (reason 'carrier-changed') [40] Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> (eth0): canceled DHCP transaction, DHCP client pid 5946 Dec 1 13:53:16 andromeda avahi-daemon[890]: Withdrawing address record for fe80::ea40:f2ff:fee2:4d86 on eth0. Dec 1 13:53:16 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:16 andromeda avahi-daemon[890]: Interface eth0.IPv6 no longer relevant for mDNS. Dec 1 13:53:16 andromeda kernel: [ 1069.025288] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Dec 1 13:53:16 andromeda avahi-daemon[890]: Withdrawing address record for 192.168.11.17 on eth0. Dec 1 13:53:16 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:16 andromeda avahi-daemon[890]: Interface eth0.IPv4 no longer relevant for mDNS. Dec 1 13:53:16 andromeda NetworkManager[1115]: <warn> DNS: plugin dnsmasq update failed Dec 1 13:53:16 andromeda NetworkManager[1115]: <info> ((null)): removing resolv.conf from /sbin/resolvconf Dec 1 13:53:16 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:16 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:16 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): carrier now ON (device state 20) Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Auto-activating connection '82579V'. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) starting connection '82579V' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Dec 1 13:53:32 andromeda kernel: [ 1084.938042] e1000e: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Dec 1 13:53:32 andromeda kernel: [ 1084.938049] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO Dec 1 13:53:32 andromeda kernel: [ 1084.938815] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> dhclient started with pid 6080 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Dec 1 13:53:32 andromeda dhclient: Internet Systems Consortium DHCP Client 4.2.4 Dec 1 13:53:32 andromeda dhclient: Copyright 2004-2012 Internet Systems Consortium. Dec 1 13:53:32 andromeda dhclient: All rights reserved. Dec 1 13:53:32 andromeda dhclient: For info, please visit https://www.isc.org/software/dhcp/ Dec 1 13:53:32 andromeda dhclient: Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed nbi -> preinit Dec 1 13:53:32 andromeda dhclient: Listening on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:53:32 andromeda dhclient: Sending on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:53:32 andromeda dhclient: Sending on Socket/fallback Dec 1 13:53:32 andromeda dhclient: DHCPREQUEST of 192.168.11.17 on eth0 to 255.255.255.255 port 67 Dec 1 13:53:32 andromeda dhclient: DHCPACK of 192.168.11.17 from 192.168.11.1 Dec 1 13:53:32 andromeda dhclient: bound to 192.168.11.17 -- renewal in 33576 seconds. Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed preinit -> reboot Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> address 192.168.11.17 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> prefix 24 (255.255.255.0) Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> gateway 192.168.11.1 Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> hostname 'andromeda' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> nameserver '192.168.11.1' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> domain name 'hsd1.ca.comcast.net' Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 1 13:53:32 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Dec 1 13:53:32 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:32 andromeda avahi-daemon[890]: New relevant interface eth0.IPv4 for mDNS. Dec 1 13:53:32 andromeda avahi-daemon[890]: Registering new address record for 192.168.11.17 on eth0.IPv4. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> (eth0): device state change: ip-config -> activated (reason 'none') [70 100 0] Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> ((null)): writing resolv.conf to /sbin/resolvconf Dec 1 13:53:33 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:33 andromeda dnsmasq[1907]: using nameserver 192.168.11.1#53 Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Policy set '82579V' (eth0) as default for IPv4 routing and DNS. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Activation (eth0) successful, device activated. Dec 1 13:53:33 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Dec 1 13:53:33 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:33 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:53:33 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:33 andromeda avahi-daemon[890]: New relevant interface eth0.IPv6 for mDNS. Dec 1 13:53:33 andromeda avahi-daemon[890]: Registering new address record for fe80::ea40:f2ff:fee2:4d86 on eth0.*. Dec 1 13:53:41 andromeda ntpdate[6154]: adjust time server 91.189.94.4 offset 0.000928 sec Dec 1 13:53:50 andromeda NetworkManager[1115]: <info> (eth0): carrier now OFF (device state 100, deferring action for 4 seconds) Dec 1 13:53:50 andromeda kernel: [ 1102.980003] e1000e: e1000e: eth0 NIC Link is Down Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): device state change: activated -> unavailable (reason 'carrier-changed') [100 20 40] Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): deactivating device (reason 'carrier-changed') [40] Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> (eth0): canceled DHCP transaction, DHCP client pid 6080 Dec 1 13:53:54 andromeda avahi-daemon[890]: Withdrawing address record for fe80::ea40:f2ff:fee2:4d86 on eth0. Dec 1 13:53:54 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:53:54 andromeda avahi-daemon[890]: Interface eth0.IPv6 no longer relevant for mDNS. Dec 1 13:53:54 andromeda avahi-daemon[890]: Withdrawing address record for 192.168.11.17 on eth0. Dec 1 13:53:54 andromeda avahi-daemon[890]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:53:54 andromeda kernel: [ 1107.025959] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready Dec 1 13:53:54 andromeda NetworkManager[1115]: <warn> DNS: plugin dnsmasq update failed Dec 1 13:53:54 andromeda NetworkManager[1115]: <info> ((null)): removing resolv.conf from /sbin/resolvconf Dec 1 13:53:54 andromeda avahi-daemon[890]: Interface eth0.IPv4 no longer relevant for mDNS. Dec 1 13:53:54 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:53:54 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:53:54 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): carrier now ON (device state 20) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: unavailable -> disconnected (reason 'carrier-changed') [20 30 40] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Auto-activating connection '82579V'. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) starting connection '82579V' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Dec 1 13:54:10 andromeda kernel: [ 1123.167668] e1000e: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Dec 1 13:54:10 andromeda kernel: [ 1123.167675] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO Dec 1 13:54:10 andromeda kernel: [ 1123.168430] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> dhclient started with pid 6212 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Dec 1 13:54:10 andromeda dhclient: Internet Systems Consortium DHCP Client 4.2.4 Dec 1 13:54:10 andromeda dhclient: Copyright 2004-2012 Internet Systems Consortium. Dec 1 13:54:10 andromeda dhclient: All rights reserved. Dec 1 13:54:10 andromeda dhclient: For info, please visit https://www.isc.org/software/dhcp/ Dec 1 13:54:10 andromeda dhclient: Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed nbi -> preinit Dec 1 13:54:10 andromeda dhclient: Listening on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:54:10 andromeda dhclient: Sending on LPF/eth0/e8:40:f2:e2:4d:86 Dec 1 13:54:10 andromeda dhclient: Sending on Socket/fallback Dec 1 13:54:10 andromeda dhclient: DHCPREQUEST of 192.168.11.17 on eth0 to 255.255.255.255 port 67 Dec 1 13:54:10 andromeda dhclient: DHCPACK of 192.168.11.17 from 192.168.11.1 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> (eth0): DHCPv4 state changed preinit -> reboot Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> address 192.168.11.17 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> prefix 24 (255.255.255.0) Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> gateway 192.168.11.1 Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> hostname 'andromeda' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> nameserver '192.168.11.1' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> domain name 'hsd1.ca.comcast.net' Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Dec 1 13:54:10 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Dec 1 13:54:10 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.11.17. Dec 1 13:54:10 andromeda dhclient: bound to 192.168.11.17 -- renewal in 35416 seconds. Dec 1 13:54:10 andromeda avahi-daemon[890]: New relevant interface eth0.IPv4 for mDNS. Dec 1 13:54:10 andromeda avahi-daemon[890]: Registering new address record for 192.168.11.17 on eth0.IPv4. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> (eth0): device state change: ip-config -> activated (reason 'none') [70 100 0] Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> ((null)): writing resolv.conf to /sbin/resolvconf Dec 1 13:54:11 andromeda dnsmasq[1907]: setting upstream servers from DBus Dec 1 13:54:11 andromeda dnsmasq[1907]: using nameserver 192.168.11.1#53 Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Policy set '82579V' (eth0) as default for IPv4 routing and DNS. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Activation (eth0) successful, device activated. Dec 1 13:54:11 andromeda NetworkManager[1115]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Dec 1 13:54:11 andromeda dbus[800]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Dec 1 13:54:11 andromeda dbus[800]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Dec 1 13:54:12 andromeda avahi-daemon[890]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::ea40:f2ff:fee2:4d86. Dec 1 13:54:12 andromeda avahi-daemon[890]: New relevant interface eth0.IPv6 for mDNS. Dec 1 13:54:12 andromeda avahi-daemon[890]: Registering new address record for fe80::ea40:f2ff:fee2:4d86 on eth0.*. Dec 1 13:54:19 andromeda ntpdate[6286]: adjust time server 91.189.94.4 offset 0.001142 sec $ lspci -v 00:19.0 Ethernet controller: Intel Corporation 82579V Gigabit Network Connection (rev 04) Subsystem: Intel Corporation Device 2031 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at f7f00000 (32-bit, non-prefetchable) [size=128K] Memory at f7f39000 (32-bit, non-prefetchable) [size=4K] I/O ports at f040 [size=32] Capabilities: [c8] Power Management version 2 Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [e0] PCI Advanced Features Kernel driver in use: e1000e Kernel modules: e1000e $ modinfo e1000e filename: /lib/modules/3.5.0-19-generic/kernel/drivers/net/e1000e/e1000e.ko version: 2.1.4-NAPI license: GPL description: Intel(R) PRO/1000 Network Driver author: Intel Corporation, <[email protected]> srcversion: 0809529BE0BBC44883956AF alias: pci:v00008086d0000153Bsv*sd*bc*sc*i* alias: pci:v00008086d0000153Asv*sd*bc*sc*i* alias: pci:v00008086d00001503sv*sd*bc*sc*i* alias: pci:v00008086d00001502sv*sd*bc*sc*i* alias: pci:v00008086d000010F0sv*sd*bc*sc*i* alias: pci:v00008086d000010EFsv*sd*bc*sc*i* alias: pci:v00008086d000010EBsv*sd*bc*sc*i* alias: pci:v00008086d000010EAsv*sd*bc*sc*i* alias: pci:v00008086d00001525sv*sd*bc*sc*i* alias: pci:v00008086d000010DFsv*sd*bc*sc*i* alias: pci:v00008086d000010DEsv*sd*bc*sc*i* alias: pci:v00008086d000010CEsv*sd*bc*sc*i* alias: pci:v00008086d000010CDsv*sd*bc*sc*i* alias: pci:v00008086d000010CCsv*sd*bc*sc*i* alias: pci:v00008086d000010CBsv*sd*bc*sc*i* alias: pci:v00008086d000010F5sv*sd*bc*sc*i* alias: pci:v00008086d000010BFsv*sd*bc*sc*i* alias: pci:v00008086d000010E5sv*sd*bc*sc*i* alias: pci:v00008086d0000294Csv*sd*bc*sc*i* alias: pci:v00008086d000010BDsv*sd*bc*sc*i* alias: pci:v00008086d000010C3sv*sd*bc*sc*i* alias: pci:v00008086d000010C2sv*sd*bc*sc*i* alias: pci:v00008086d000010C0sv*sd*bc*sc*i* alias: pci:v00008086d00001501sv*sd*bc*sc*i* alias: pci:v00008086d00001049sv*sd*bc*sc*i* alias: pci:v00008086d0000104Dsv*sd*bc*sc*i* alias: pci:v00008086d0000104Bsv*sd*bc*sc*i* alias: pci:v00008086d0000104Asv*sd*bc*sc*i* alias: pci:v00008086d000010C4sv*sd*bc*sc*i* alias: pci:v00008086d000010C5sv*sd*bc*sc*i* alias: pci:v00008086d0000104Csv*sd*bc*sc*i* alias: pci:v00008086d000010BBsv*sd*bc*sc*i* alias: pci:v00008086d00001098sv*sd*bc*sc*i* alias: pci:v00008086d000010BAsv*sd*bc*sc*i* alias: pci:v00008086d00001096sv*sd*bc*sc*i* alias: pci:v00008086d0000150Csv*sd*bc*sc*i* alias: pci:v00008086d000010F6sv*sd*bc*sc*i* alias: pci:v00008086d000010D3sv*sd*bc*sc*i* alias: pci:v00008086d0000109Asv*sd*bc*sc*i* alias: pci:v00008086d0000108Csv*sd*bc*sc*i* alias: pci:v00008086d0000108Bsv*sd*bc*sc*i* alias: pci:v00008086d0000107Fsv*sd*bc*sc*i* alias: pci:v00008086d0000107Esv*sd*bc*sc*i* alias: pci:v00008086d0000107Dsv*sd*bc*sc*i* alias: pci:v00008086d000010B9sv*sd*bc*sc*i* alias: pci:v00008086d000010D5sv*sd*bc*sc*i* alias: pci:v00008086d000010DAsv*sd*bc*sc*i* alias: pci:v00008086d000010D9sv*sd*bc*sc*i* alias: pci:v00008086d00001060sv*sd*bc*sc*i* alias: pci:v00008086d000010A5sv*sd*bc*sc*i* alias: pci:v00008086d000010BCsv*sd*bc*sc*i* alias: pci:v00008086d000010A4sv*sd*bc*sc*i* alias: pci:v00008086d0000105Fsv*sd*bc*sc*i* alias: pci:v00008086d0000105Esv*sd*bc*sc*i* depends: vermagic: 3.5.0-19-generic SMP mod_unload modversions parm: copybreak:Maximum size of packet that is copied to a new buffer on receive (uint) parm: TxIntDelay:Transmit Interrupt Delay (array of int) parm: TxAbsIntDelay:Transmit Absolute Interrupt Delay (array of int) parm: RxIntDelay:Receive Interrupt Delay (array of int) parm: RxAbsIntDelay:Receive Absolute Interrupt Delay (array of int) parm: InterruptThrottleRate:Interrupt Throttling Rate (array of int) parm: IntMode:Interrupt Mode (array of int) parm: SmartPowerDownEnable:Enable PHY smart power down (array of int) parm: KumeranLockLoss:Enable Kumeran lock loss workaround (array of int) parm: CrcStripping:Enable CRC Stripping, disable if your BMC needs the CRC (array of int) parm: EEE:Enable/disable on parts that support the feature (array of int) parm: Node:[ROUTING] Node to allocate memory on, default -1 (array of int) parm: debug:Debug level (0=none,...,16=all) (int)

  Read the article

• Facebook: Hide Your Status Updates From Your Boss/Ex or Any Specific Friend

  - by Gopinath

  Sometime we want to hide our status updates from specific people who are already accepted as Friends in Facebook. Do you wonder why we need to accept someone as friend and then hide status updates from them? Well, may be you have to accept a friend request from your boss, but certainly love to hide status updates as well as other Facebook activities from him. Something similar goes with few annoying friends whom you cant’ de-friend but like to hide your updates. Thanks to Facebook for providing fine grain privacy options on controlling what we want to share and with whom we want to share. It’s very easy to block one or more specific friends from seeing your status updates. Here are the step by step instructions: 1. Login to Facebook and go to Privacy Settings Page. It shows a page something similar to what is shown in the below image. 2. Click on “Customize settings” link 3. Expand the privacy options available in the section Things I Share -> Posts by me. Choose Customise from the list of available options   4. Type the list of unwanted friend’s names in to input box of the section "Hide this from”. Here is a screen grab of couple of my friends whom I added for writing this post 5. Click the Save Settings button. That’s all. Facebook will ensure that these people will not see your status updates on their news feed. Enjoyed the Facebook Tip? Join Tech Dreams on Facebook to read all our blog posts on your Facebook’s news feed. Join us on Facebook to read all our stories right inside your Facebook news feed.

  Read the article

• Business Continuity for EBS Using Oracle 11g Physical Standby DB

  - by Steven Chan

  Our Applications Technology Group database architects have released two new documents covering the use of Oracle Data Guard to create physical standby databases for Oracle E-Business Suite environments:Business Continuity for Oracle E-Business Release 12 Using Oracle 11g Physical Standby Database (Note 1070033.1)Business Continuity for Oracle E-Business Release 11i Using Oracle 11g Physical Standby Database (Note 1068913.1)

  Read the article

• Best solution for multiplayer realtime Android game

  - by piotrek

  I plan to make multiplayer realtime game for Android (2-8 players), and I consider, which solution for multiplayer organization is the best: Make server on PC, and client on mobile, all communition go through server ( ClientA - PC SERVER - All Clients ) Use bluetooth, I don't used yet, and I don't know is it hard to make multiplayer on bluetooth Make server on one of devices, and other devices connect ( through network, but I don't know is it hard to resolve problem with devices over NAT ? ) Other solution ?

  Read the article

• Best way to start in C# and Raknet?

  - by cad

  I am trying to learn Raknet from C# and I found it extremely confusing. Raknet tutorial seems to work easy and nice in C++. I have already make some chat server code from tutorial. But I am looking to do something similar in C# and I find a mess. - Seems that I need to compile raknet using SWIG to have like an interface? - Also I have found a project called raknetdotnet but seems abandoned..(http://code.google.com/p/raknetdotnet/) So my main question is what is the best way to code in C# using raknet? As secondary questions: Anyone can recomend me good tutorial in raknet AND c#? Is there any sample C# code that I can download? I have readed lot of pages but I didn't get anything clear so I hope someone that has lived this before can help me. Thanks PD: Maybe raknet is obsolete (I find a lot of code and posts from 2007) and there is a better tool to achieve what I want. (I am interested in making a game with a dedicated server.)

  Read the article

• Why is my machine unable to mount my SMB drives ("CIFS VFS: Error connecting to socket. Aborting operation", return code -115)?

  - by downbeat

  I have a machine running Precise (12.04 x64), and I cannot mount my SMB drives (I have 3, we'll call them public, private and download). It used to work (a week or two ago) and I didn't touch fstab! The machine hosting the shares is a commercial NAS, and I'm not seeing anything that would indicate it's an issue with the NAS. I have an older machine which I updated to Precise at the same time (both fresh installed, not dist-upgrade), so should have a very similar configuration. It is not having any problems. I am not having problems on windows machines/partitions either, only one of my Precise machines. The two machines are using identical entries in fstab and identical /etc/samba/smb.conf files. I don't think I've ever changed smb.conf (has never mattered before). My fstab entries all basically look like this: //10.1.1.111/public /media/public cifs credentials=/home/downbeat/.credentials,iocharset=utf8,uid=downbeat,gid=downbeat,file_mode=0644,dir_mode=0755 0 0 Here's the dmesg output on boot: [ 51.162198] CIFS VFS: Error connecting to socket. Aborting operation [ 51.162369] CIFS VFS: cifs_mount failed w/return code = -115 [ 51.194106] CIFS VFS: Error connecting to socket. Aborting operation [ 51.194250] CIFS VFS: cifs_mount failed w/return code = -115 [ 51.198120] CIFS VFS: Error connecting to socket. Aborting operation [ 51.198243] CIFS VFS: cifs_mount failed w/return code = -115 There are no other errors I see in the dmesg output. Originally when I ran 'testparm -s', the output contained these lines ERROR: lock directory /var/run/samba does not exist ERROR: pid directory /var/run/samba does not exist Here's the samba related programs I have installed: $ dpkg --list|grep -i samba ii libpam-winbind 2:3.6.3-2ubuntu2.3 Samba nameservice and authentication integration plugins ii libwbclient0 2:3.6.3-2ubuntu2.3 Samba winbind client library ii nautilus-share 0.7.3-1ubuntu2 Nautilus extension to share folder using Samba ii python-smbc 1.0.13-0ubuntu1 Python bindings for Samba clients (libsmbclient) ii samba-common 2:3.6.3-2ubuntu2.3 common files used by both the Samba server and client ii samba-common-bin 2:3.6.3-2ubuntu2.3 common files used by both the Samba server and client ii winbind 2:3.6.3-2ubuntu2.3 Samba nameservice integration server $ dpkg --list|grep -i smb ii dmidecode 2.11-4 SMBIOS/DMI table decoder ii libsmbclient 2:3.6.3-2ubuntu2.3 shared library for communication with SMB/CIFS servers ii python-smbc 1.0.13-0ubuntu1 Python bindings for Samba clients (libsmbclient) ii smbclient 2:3.6.3-2ubuntu2.3 command-line SMB/CIFS clients for Unix ii smbfs 2:5.1-1ubuntu1 Common Internet File System utilities - compatibility package $ dpkg --list|grep -i cifs ii cifs-utils 2:5.1-1ubuntu1 Common Internet File System utilities ii libsmbclient 2:3.6.3-2ubuntu2.3 shared library for communication with SMB/CIFS servers ii smbclient 2:3.6.3-2ubuntu2.3 command-line SMB/CIFS clients for Unix I originally noticed that my other machine had "libpam-winbind" and "nautilus-share" installed and the machine with the issue did not. Installing those two packages solved my errors with 'testparm -s', but did not fix my issue. Finally, I tried to purge and reinstall these packages smbclient smbfs cifs-utils samba-common samba-common-bin Still no luck. Again, it used to work; now it doesn't. Very similarly configured machine works (but some packages are out of date on the working machine). The NAS has only one interface/IP address, nmblookup works to find it's IP from it's hostname (from the machine with the issue) and it responds to a ping. Please any help would be great. I've been searching on AskUbuntu, SuperUser, ubuntuforums and plain old search engines for a week now and it's driving me crazy!

  Read the article

• Network config with pppoe and Ubuntu 13.10

  - by Pavel

  I have an internet connection that is using pppoe. In my windows I do not assign an ip address for my network and I am able to connect using password and username. I installed Ubintu 13.10 today, and I did pppoeconf, and I setup an ip/network mask and changed the mac address in the options, and I was able to connect to the Internet. I restarted the computer, and I got a message saying that the wired connection is not managed. Internet was not working. I went to network manager file, and I changed the option to true, but I still can't connect to the Internet. I am pretty new to linux. How can I get my Internet working? Thanks

  Read the article

• Which LAN card / module combinations proven to work with Wake on LAN

  - by pablomo

  I've got a 12.04 headless server that I've been trying to get to work with wake-on-lan. The card is Marvel 88E8053 using the sky2 module. Although WOL is enabled in BIOS and ethtool shows the card as WOL enabled, it refuses to wake when I send the magic packet. I have verified that the packet is being received OK when the machine is on. The machine does wake OK from a BIOS alarm which suggests it is a network card issue. I've seen reference to bugs in sky2 that mean WOL fails in recent versions of Ubuntu (and have tried a module conf file as suggested here but to no avail) So I am thinking the best bet is to replace the ethernet card with one that definitely works with WOL in 12.04 - please could you post your card make and model no if you are using it successfully?

  Read the article

• Cant add network printer with system-config-printer package

  - by Erick David Ruiz Coronel

  Hello im new here and I dont know if im doing it right but I hope yes. I have a printer conected to a windows 8 machine, also I had ubuntu 13.04 and it worked fine when I printed from linux to windows but when I upgraded to 13.10 my printer didnt worked, I removed it thinking that would fix it but when I tryed to add the printer again I couldnt, I reinstalled cups and the system-config-printer-gnome package but didnt worked. Here is the terminal log : erick@Tauro:~$ system-config-printer Caught non-fatal exception. Traceback: File "/usr/share/system-config-printer/probe_printer.py", line 255, in _do_find fn () File "/usr/share/system-config-printer/probe_printer.py", line 367, in _probe_hplip stderr=null) File "/usr/lib/python2.7/subprocess.py", line 709, in init errread, errwrite) File "/usr/lib/python2.7/subprocess.py", line 1326, in _execute_child raise child_exception OSError: [Errno 2] No existe el archivo o el directorio Continuing anyway.. Traceback (most recent call last): File "/usr/share/system-config-printer/newprinter.py", line 912, in on_btnNPForward_clicked self.nextNPTab() File "/usr/share/system-config-printer/newprinter.py", line 1064, in nextNPTab stderr=file("/dev/null")) File "/usr/lib/python2.7/subprocess.py", line 709, in init errread, errwrite) File "/usr/lib/python2.7/subprocess.py", line 1326, in _execute_child raise child_exception OSError: [Errno 2] No existe el archivo o el directorio Any suggestion please? C:

  Read the article

• What to send to server in real time FPS game?

  - by syloc

  What is the right way to tell the position of our local player to the server? Some documents say that it is better to send the inputs whenever they are produced. And some documents say the client sends its position in a fixed interval. With the sending the inputs approach: What should I do if the player is holding down the direction keys? It means I need to send a package to the server in every frame. Isn't it too much? And there is also the rotation of the player from the mouse input. Here is an example: http://www.gabrielgambetta.com/fpm_live.html What about sending the position in fixed interval approach. It sends too few messages to the server. But it also reduces responsiveness. So which way is better?

  Read the article

• dsl modem problem in ubuntu 11.10

  - by Misterious

  Earlier I used Windows 7 and the modem used to work absolutely fine. Even when it disconnected it used to reconnect automatically without any trouble. But then I installed Ubuntu 11.10 on dual boot and set up the modem connection properly but the modem now disconnects much more frequently(eariler it disconnected once in 5 hours or so and after ubuntu in 5 minutes!!). Also once disconnected it does not reconnect even when i have checked the connect automatically button. I have to restart the system to reconnect it. Also then I clean installed windows and modem works perfectly fine again. What is the reason for this and how can I solve this? I really want to use ubuntu but due to this problem I cant. Sorry for my poor English.

  Read the article

• How do i find out which program is using internet and how much?

  - by Anwar Shah

  Sometimes there are unusual Internet activity in my Computer. Modem's lights are always blinking and When I open system monitor, I see there some unknown program is using my precious Internet with 64KB/S (I have 512kbps connection). Still I am in a firefox session with only one tab opened, and the page in already loaded and there is no indication of busy sign in the page (that rotating orange circle). In that situation I unplug my modem and reconnect it again. After several times doing this, that unusual activity stops. It annoys me very much. How can I find out the process which is using the Internet?. How much they are using? How can I kill it? A graphical solution will be better.

  Read the article

• Ubuntu Minimal in the new Intel NUC Haswell

  - by Ernie

  I have one the of the new Haswell NUCs that just came out - D34010WYK. https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=23089&lang=eng&OSVersion=OS%20Independent&DownloadType=Documentation), I tried to load ubuntu minimal 13.10 x64 from the mini.iso and it cannot properly detect a network during install - my guess is a driver issue. Tried 12.04 lts and it doesnt even see the NIC at all. Is there anything I could do to get one of the current versions to see the network properly? I did try the latest trusty nightly desktop and it did install without issue. Is there a minimal version of that? Thanks Ernie

  Read the article

• P2P synchronization: can a player update fields of other players?

  - by CherryQu

  I know that synchronization is a huge topic, so I have minimized the problem to this example case. Let's say, Alice and Bob are playing a P2P game, fighting against each other. If Alice hits Bob, how should I do the network component to make Bob's HP decrease? I can think of two approaches: Alice perform a Bob.HP--, then send Bob's reduced HP to Bob. Alice send a "I just hit Bob" signal to Bob. Bob checks it, and reduce its own HP, then send his new HP to everyone including Alice. I think the second approach is better because I don't think a player in a P2P game should be able to modify other players' private fields. Otherwise cheating would be too easy, right? My philosophy is that in a P2P game especially, a player's attributes and all attributes of its belonging objects should only be updated by the player himself. However, I can't prove that this is right. Could someone give me some evidence? Thanks :)

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >