Search Results

Search found 4913 results on 197 pages for 'ps cjef'.

Page 87/197 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• Dock with dual external DVI monitors with Intel + Nvidia Optimus?

  - by Ryan

  I have a Dell Latitude E6420 laptop plugged into a docking station, and the dock has 2 monitors (connected with DVI). Also note that I've installed Ubuntu alongside (dual-boot) Windows 7. I can't get the dual monitors to work both on Ubuntu (either 11.10 or 12.04) and Windows 7. When I run lspci | grep VGA, I get: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF108 [Quadro NVS 4200M] (rev a1) If I then reboot and uncheck Optimus setting in the BIOS during reboot, I'm able to get the dual monitors to work in Ubuntu 12.04 (but I need to configure them every boot in Nvidia Settings). When I run lspci | grep VGA, I get: 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [Quadro NVS 4200M] (rev a1) But then if I reboot into Windows (leaving the Optimus unchecked), Windows can't detect external monitors, and the resolution is unacceptably low. I've seen on many forum posts that this particular graphics card setup causes lots of headaches. I haven't been able to resolve my problem yet. How can I use my external display on my laptop with intel and nvidia video cards? How to use external displays with Intel driver on a NVidia/Intel hybrid system nVidia Optimus , Unity 3D and Dual Monitors "Just use VGA instead of DVI" isn't an option because my dock has only 1 VGA port (and 2 DVI). Switching the BIOS setting on every reboot and then reconfiguring the display settings every time is tedious, time-consuming, and impractical. Do you know how to make this work smoothly? Thanks for your help! P.S. see also: http://superuser.com/questions/434358/dell-latitude-e6420-dual-boot-ubuntu-windows-7-optimus-graphics-problems

  Read the article

• How to know which partition is which?

  - by user206870

  Well I was just wondering what partition belongs to which. On my computer I have Windows 7 and two Ubuntu systems (it was an accident, which is why I need to know which partition is which). So how do I know which one is which?? PS here's the codes: jp@jp-Satellite-L555D:~$ sudo update-grub [sudo] password for jp: Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.11.0-12-generic Found initrd image: /boot/initrd.img-3.11.0-12-generic Found memtest86+ image: /boot/memtest86+.bin Found Windows 7 (loader) on /dev/sda1 Found Windows 7 (loader) on /dev/sda2 Found Windows Recovery Environment (loader) on /dev/sda3 Found Ubuntu 13.10 (13.10) on /dev/sda7 done jp@jp-Satellite-L555D:~$ sudo fdisk -l Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf6f5148e Device Boot Start End Blocks Id System /dev/sda1 * 2048 3074047 1536000 27 Hidden NTFS WinRE /dev/sda2 3074048 213421022 105173487+ 7 HPFS/NTFS/exFAT /dev/sda3 469676032 488396799 9360384 17 Hidden HPFS/NTFS /dev/sda4 213422078 469676031 128126977 5 Extended /dev/sda5 300185600 463910911 81862656 83 Linux /dev/sda6 463912960 469676031 2881536 82 Linux swap / Solaris /dev/sda7 213422080 300185599 43381760 83 Linux Partition table entries are not in disk order Thanks to whoever can answer this. Another quick question, what is the extended partition??

  Read the article

• Pattern for Accessing MySQL connection

  - by Dipan Mehta

  We have an application which is C++ trying to access MySQL database. There are several (about 5 or so) threads in the application (with Boost library for threading) and in each thread has a few objects, each of which is trying to access Database for its' own purpose. It has a simple ORM kind of model but that really is not an important factor here. There are three potential access patterns i can think of: There could be single connection object per application or thread and is shared between all (or group). The object needs to be thread safe and there will be contentions but MySQL will not be fired with too many connections. Every object could initiate connection on its own. The database needs to take care of concurrency (which i think MySQL can) and the design could be much simpler. There could be two possibilities here. a. either object keeps a persistent connection for its life OR b. object initiate connection as and when needed. To simplify the contention as in case of 1 and not to create too many sockets as in case of 2, we can have group/set based connections. So there could be there could be more than one connection (say N), each of this connection could be shared connection across M objects. Naturally, each of the pattern has different resource cost and would work under different constraints and objectives. What criteria should i use to choose the pattern of this for my own application? What are some of the advantages and disadvantages of each of these pattern over the other? Are there any other pattern which is better? PS: I have been through these questions: mysql, one connection vs multiple and MySQL with mutiple threads and processes But they don't quite answer exactly what i am trying to ask.

  Read the article

• Execute a SSIS package in Sync or Async mode from SQL Server 2012

  - by Davide Mauri

  Today I had to schedule a package stored in the shiny new SSIS Catalog store that can be enabled with SQL Server 2012. (http://msdn.microsoft.com/en-us/library/hh479588(v=SQL.110).aspx) Once your packages are stored here, they will be executed using the new stored procedures created for this purpose. This is the script that will get executed if you try to execute your packages right from management studio or through a SQL Server Agent job, will be similar to the following: Declare @execution_id bigint EXEC [SSISDB].[catalog].[create_execution] @package_name='my_package.dtsx', @execution_id=@execution_id OUTPUT, @folder_name=N'BI', @project_name=N'DWH', @use32bitruntime=False, @reference_id=Null Select @execution_id DECLARE @var0 smallint = 1 EXEC [SSISDB].[catalog].[set_execution_parameter_value] @execution_id,  @object_type=50, @parameter_name=N'LOGGING_LEVEL', @parameter_value=@var0 DECLARE @var1 bit = 0 EXEC [SSISDB].[catalog].[set_execution_parameter_value] @execution_id,  @object_type=50, @parameter_name=N'DUMP_ON_ERROR', @parameter_value=@var1 EXEC [SSISDB].[catalog].[start_execution] @execution_id GO The problem here is that the procedure will simply start the execution of the package and will return as soon as the package as been started…thus giving you the opportunity to execute packages asynchrously from your T-SQL code. This is just *great*, but what happens if I what to execute a package and WAIT for it to finish (and thus having a synchronous execution of it)? You have to be sure that you add the “SYNCHRONIZED” parameter to the package execution. Before the start_execution procedure: exec [SSISDB].[catalog].[set_execution_parameter_value] @execution_id,  @object_type=50, @parameter_name=N'SYNCHRONIZED', @parameter_value=1 And that’s it . PS From the RC0, the SYNCHRONIZED parameter is automatically added each time you schedule a package execution through the SQL Server Agent. If you’re using an external scheduler, just keep this post in mind .

  Read the article

• Gimpshop 2.8. Available for Win & Mac. No Linux version?

  - by Jorge M. Treviño

  Finally got around to upgrading 12.04 to 12.10. One of the nice things about the new version is that Gimp 2.8 is in the repositories. Installed and it's a far cry from the 2.2, 2.4 and 2.6 versions which were —at least from my untrained point of view– next to unusable. Now 2.8 is a much more intuitive, for Photoshop users at least, and I'm trying to really learn it. Browsing around, I found that there's s new version of Gimpshop, something that was a sorely amateurish attempt to a PS interface over an old Gimp version and sure to mess up your system. Seeing "2.8" prominently displayed in the page, I decided to try the Windows version. Oddly, there's a Mac version too but no Linux one. The link directs one to a non-existent file in one of the cloud storage sites. After the Win version was installed, I fired it up and, surprise!, it's exactly the same as I can tell without diving into menus and dialogs, as the plain vanilla Ubuntu version I have installed. Can anybody shed light on what goes on here? Is this a scheme to get inadvertent users to install some "optional extras" that come with the installer? Very curious about it (thanks God I'm not a cat ).

  Read the article

• Getting MTP to work with a Galaxy tab 2 7.0?

  - by Wouter

  I'm trying to get MTP with the galaxy tab 2 7.0 working on my ubuntu installation. Such that I can access the files. I tried to do what is described here: http://www.omgubuntu.co.uk/2011/12/how-to-connect-your-android-ice-cream-sandwich-phone-to-ubuntu-for-file-access I however fail at executing one of the following commands mtp-detect | grep idVendor mtp-detect | grep idProduct This fails [20:42|0] $ mtp-detect | grep idVender Device 0 (VID=04e8 and PID=6860) is a Samsung GT-P7310/P7510/N7000/I9100/Galaxy Tab 7.7/10.1/S2/Nexus/Note. PTP_ERROR_IO: failed to open session, trying again after resetting USB interface LIBMTP libusb: Attempt to reset device LIBMTP PANIC: failed to open session on second attempt Unable to open raw device 0 [20:44|0] $ mtp-detect | grep idProduct Device 0 (VID=04e8 and PID=6860) is a Samsung GT-P7310/P7510/N7000/I9100/Galaxy Tab 7.7/10.1/S2/Nexus/Note. PTP_ERROR_IO: failed to open session, trying again after resetting USB interface LIBMTP libusb: Attempt to reset device LIBMTP PANIC: failed to open session on second attempt Unable to open raw device 0 Now my guess was was that the idVender is the same as the VID (04e8) and the idProduct is the same as PID (6860) Now I continued to work with those values and completed the tutorial. When finished I tried android-connect This returned fuse: bad mount point `/media/GalaxyTab': Transport endpoint is not connected Does anybody have a clue what to do? Also I want to note that when I connect my GalaxyTab 2 7.0 that I still get a pop-up of ubuntu that a device was connected. I also can still see the mapstructure, the problem however is is that all the folders have 0 bytes and do not have any subfolders. I can only see the folders in the root. ps. I also checked a similar question and tried what is described in this answer http://askubuntu.com/a/88630/27480

  Read the article

• Powershell variables to string

  - by Mike Koerner

  I'm new to powershell. I'm trying to write an error handler to wrap around my script.  Part of the error handler is dumping out some variable settings.  I spent a while trying to do this and couldn't google a complete solution so I thought I'd post something. I want to display the $myinvocation variable. In powershell you can do this PS C:\> $myInvocation for my purpose I want to create a stringbuilder object and append the $myinvocation info.  I tried this $sbOut = new-object System.Text.Stringbuilder $sbOut.appendLine($myinvocation) $sbOut.ToString() This produces                                    Capacity                                MaxCapacity                                     Length                                    --------                                -----------                                     ------                                          86                                 2147483647                                         45 System.Management.Automation.InvocationInfo This is not what I wanted so I tried $sbOut.appendLine(($myinvocation|format-list *)) This produced                                    Capacity                                MaxCapacity                                     Length                                    --------                                -----------                                     ------                                         606                                 2147483647                                        305 Microsoft.PowerShell.Commands.Internal.Format.FormatStartData Microsoft.PowerShell.Commands.Internal.Format.GroupStartData Micros oft.PowerShell.Commands.Internal.Format.FormatEntryData Microsoft.PowerShell.Commands.Internal.Format.GroupEndData Microsoft.Powe rShell.Commands.Internal.Format.FormatEndData Finally I figured out how to produce what I wanted: $sbOut = new-object System.Text.Stringbuilder [void]$sbOut.appendLine(($myinvocation|out-string)) $sbOut.ToString() MyCommand        : $sbOut = new-object System.Text.Stringbuilder                                    [void]$sbOut.appendLine(($myinvocation|out-string))                                      $sbOut.ToString()                    BoundParameters  : {} UnboundArguments : {} ScriptLineNumber : 0 OffsetInLine     : 0 HistoryId        : 13 ScriptName       : Line             : PositionMessage  : InvocationName   : PipelineLength   : 2 PipelinePosition : 1 ExpectingInput   : False CommandOrigin    : Runspace Note the [void] in front of the stringbuilder variable doesn't show the Capacity,MaxCapacity of the stringbuilder object.  The pipe to out-string makes the output a string. It's not pretty but it works.

  Read the article

• Workaround: build FBX in XNA raise OutOfMemoryException

  - by Vitus

  If you try to add large FBX 3D model to the XNA project, and build it, you can get an OutOfMemoryException build error like following: Error    1    Building content threw OutOfMemoryException: Exception of type 'System.OutOfMemoryException' was thrown.    at System.Collections.Generic.List`1.set_Capacity(Int32 value)    at System.Collections.Generic.List`1.EnsureCapacity(Int32 min)    at System.Collections.Generic.List`1.InsertRange(Int32 index, IEnumerable`1 collection)    at Microsoft.Xna.Framework.Content.Pipeline.Graphics.VertexChannel`1.InsertRange(Int32 index, Int32 count)    at Microsoft.Xna.Framework.Content.Pipeline.Graphics.VertexContent.InsertRange(Int32 index, IEnumerable`1 positionIndexCollection)    at Microsoft.Xna.Framework.Content.Pipeline.Graphics.MeshBuilder.AddTriangleVertex(Int32 indexIntoVertexCollection)    at Microsoft.Xna.Framework.Content.Pipeline.MeshConverter.FillNodeWithInfoFromMesh(KFbxNode* fbxNode, String name, KFbxGeometryConverter* geometryConverter)    at Microsoft.Xna.Framework.Content.Pipeline.FbxImporter.ProcessInformationInNode(KFbxNode* fbxNode, String name, Boolean* partOfMainSkeleton, Boolean* warnIfBoneButNotChild)    at Microsoft.Xna.Framework.Content.Pipeline.FbxImporter.ProcessNode(ValueType parentAbsoluteTransform, NodeContent potentialParent, KFbxNode* fbxNode, Boolean partOfMainSkeleton, Boolean warnIfBoneButNotChild)    at Microsoft.Xna.Framework.Content.Pipeline.FbxImporter.ProcessNode(ValueType parentAbsoluteTransform, NodeContent potentialParent, KFbxNode* fbxNode, Boolean partOfMainSkeleton, Boolean warnIfBoneButNotChild)    at Microsoft.Xna.Framework.Content.Pipeline.FbxImporter.Import(String filename, ContentImporterContext context)    at Microsoft.Xna.Framework.Content.Pipeline.ContentImporter`1.Microsoft.Xna.Framework.Content.Pipeline.IContentImporter.Import(String filename, ContentImporterContext context)    //additional calls here …   My desktop PC have 8Gb RAM, and Visual Studio’s process devenv.exe use under 2Gb of it while build process (about 3.5-4Gb of RAM is always free). It’s obvious, that VS can’t address more than 2Gb of RAM, and when that limit is over, build process is fail. OS on my PC is Win x64,  so I “charge” devenv.exe by using editbin.exe utility – in the VS Command prompt I run following: editbin "C:\Program Files (x86)\Microsoft Visual Studio 10.0\Common7\IDE\devenv.exe" /LARGEADDRESSAWARE This command edits the image to indicate that the application can handle addresses larger than 2 gigabytes. After that FBX file successfully built! Of course, you must put proper path to devenv.exe, depend on your installation path. If you are on Win x86, you need to do additional action – more info here.   P.S.: although now you can build a bigger files, than usual, keep in mind, that XNA have some restrictions on vertex buffer size etc., depend on your current XNA project profile (Reach or HiDef). And if your model’s vertexbuffer size more than 64Mb (with Reach profile), that model can’t be built and raise an error.

  Read the article

• Are very short or abbreviated method/function names that don't use full words bad practice or a matter of style.

  - by Alb

  Is there nowadays any case for brevity over clarity with method names? Tonight I came across the Python method repr() which seems like a bad name for a method to me. It's not an English word. It apparently is an abbreviation of 'representation' and even if you can deduce that, it still doesn't tell you what the method does. A good method name is subjective to a certain degree, but I had assumed that modern best practices agreed that names should be at least full words and descriptive enough to reveal enough about the method that you would easily find one when looking for it. Method names made from words help let your code read like English. repr() seems to have no advantages as a name other than being short and IDE auto-complete makes this a non-issue. An additional reason given in an answer is that python names are brief so that you can do many things on one line. Surely the better way is to just extract the many things to their own function, and repeat until lines are not too long. Are these just a hangover from the unix way of doing things? Commands with names like ls, rm, ps and du (if you could call those names) were hard to find and hard to remember. I know that the everyday usage of commands such as these is different than methods in code so the matter of whether those are bad names is a different matter.

  Read the article

• Why do programmers write applications and then make them free?

  - by Ken

  As an entrepreneur/programmer who makes a good living from writing and selling software, I'm dumbfounded as to why developers write applications and then put them up on the Internet for free. You've found yourself in one of the most lucrative fields in the world. A business with 99% profit margin, where you have no physical product but can name your price; a business where you can ship a buggy product and the customer will still buy it. Occasionally some of our software will get a free competitor, and I think, this guy is crazy. He could be making a good living off of this but instead chose to make it free. Do you not like giant piles of money? Are you not confident that people would pay for it? Are you afraid of having to support it? It's bad for the business of programming because now customers expect to be able to find a free solution to every problem. (I see tweets like "is there any good FREE software for XYZ? or do I need to pay $20 for that".) It's also bad for customers because the free solutions eventually break (because of a new OS or what have you) and since it's free, the developer has no reason to fix it. Customers end up with free but stale software that no longer works and never gets updated. Customer cries. Developer still working day job cries in their cubical. What gives? PS: I'm not looking to start an open-source/software should be free kind of debate. I'm talking about when developers make a closed source application and make it free.

  Read the article

• Little mysterious RowMatch

  - by kishore.kondepudi(at)oracle.com

  Incidentally this was the first piece of code i ever wrote in ADF.The requirement was we have tax rates which are read from a table.And there can be different type of tax rates called certificates or exceptions based on the rate_type column in the tax rates table.The simplest design i chose was to create an EO on the tax rates table and create two VO's called CertificateVO and ExceptionVO based on the same EO.So far so good.I wrote all the business logic in the EO and completed the model project.The CertificateVO has the query as select * from tax_rates TaxRateEO where rate_type='CERTIFICATE' and similary the ExceptionVO is also built.The UI is pretty simple and it has two tabs called Certificates and Exceptions and each table has a button to create a tax rate.The certificate tab is driven by CertificateVO and exception tab is driven by ExceptionVO.The CertificateVO has default value of rate_type set to 'CERTIFICATE' and ExceptionVO has default value of rate_type to 'EXCEPTION' to default values for new records.So far so good.But on running the UI i noticed a strange thing,When i create a new row in Certificate i see the same row in Exception too and vice-versa.i.e; what ever row i create in one VO it also appears in the second one although it shouldn't be.I couldn't understand the reason for behavior even though an explicit where clause is present.Digging through documentation i found that ADF doesnt apply the where clause to new rows instead it applies something called as RowMatch to them.RowMatch in simple terms is a where condition applied to the VO rows at runtime.Since we had both VO's based on the same EO we have the same entity cache.The filter factor for new rows to be shown in VO at runtime is actually RowMatch than the where clause defined in the VO.The default RowMatch is empty as a result any new row appears in both the VO's since its from same entity cache.The solution to this problem is to use polymorphic view objects which can do the row filter based on configuration or override the getRowMatch() method in the VOImpl and pass the custom where filter instead of default RowMatch.Eg:@Overridepublic RowMatch getRowMatch(){    return new RowMatch("rate_type='CERTIFICATE'");}similarly for ExceptionVO too.With proper RowMatch in place new rows will route themselves to appropriate VO.PS: The behavior(Same row pushed to both VO's from entity cache) is also called as ViewLink Consistency.Try it out!

  Read the article

• Why is my Wacom Intuos tablet not detected?

  - by mjwittering

  I need a little help trying to install a Wacom Intuos tablet, model number CTL-480/S. My installation of Ubuntu 13.04, 64bit, doesn't seem to be able to detect the device. I've tried an few different USB ports on my machine and get the same result. I believe there is an issue because when I open the System Settings app from the launcher and browse to the Wacom Tablet section under hardware, it reports that there is 'No table detected'. When I use lsusb I can see the device is detected: Bus 003 Device 004: ID 056a:030e Wacom Co., Ltd I've also pulled the following from the syslog: Oct 16 16:51:05 earth kernel: [ 7062.388031] usb 3-5: new full-speed USB device number 4 using ohci_hcd Oct 16 16:51:05 earth kernel: [ 7062.611038] usb 3-5: New USB device found, idVendor=056a, idProduct=030e Oct 16 16:51:05 earth kernel: [ 7062.611042] usb 3-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 Oct 16 16:51:05 earth kernel: [ 7062.611045] usb 3-5: Product: Intuos PS Oct 16 16:51:05 earth kernel: [ 7062.611047] usb 3-5: Manufacturer: Wacom Co.,Ltd. Oct 16 16:51:05 earth mtp-probe: checking bus 3, device 4: "/sys/devices/pci0000:00/0000:00:02.0/usb3/3-5" Oct 16 16:51:05 earth mtp-probe: bus: 3, device: 4 was not an MTP device I'd really appreciate any suggestions to help debug and install this device.

  Read the article

• Partial upgrade on 12.04, how to stop nagging after locking to a working NVIDIA & xorg

  - by alsk

  How to stop the upgrade manager from offering updates and upgrades that potentially would harm my working 2D and 3D graphics? Finally, I got 12.04 working as it should: with nvidia-173 drivers by downgrading xorg and locking the version: On my 32-bit system on Athlon64, with (Albatron) NVIDIA GeForce FX5700XT, locked (/pinned) to xorg 1:7.6-7ubuntu7, xserver-xorg-core 2:11.1-0obuntu10.07, nvidia-173 173.14.35-0ubuntu0.2? An annoying thing left is that every time the updates are checked, I get warning of partial updates, and ambiguous options of "partial update" and "close". Ambiguous in that sense that if I click close, I will get option to update a few packages, which has been OK, while "partial update" would like to update my kernel to 3.2, alter xorg, remove nvidia-173 etc., and update mesa etc. This is not what I call appropriate, after locking XORG and NVIDIA drivers to working ones. One may say according to package management logic it may be correct, but to me as an user it makes little sense. Last Ubuntu that worked without big mess for me was 10.10, hence I will not put 12.10 to my "production" system, until I can be sure it will not trash the system again. P.S. Is there a recommended way to keep NVIDIA GeForce FX working with 3D on Ubuntu... in future?

  Read the article

• Music While Coding [closed]

  - by inspectorG4dget

  Hi SO, Generally, while I'm coding, I prefer to listen to some background music. Nothing that'll get me distracted, but something that'll help keep the rhythm and isn't counterproductive when I need to stop coding to debug or to think of a way to solve a small problem that stands in the way of progress. Now, I have read some similar questions on reddit and on SO - specifically: which songs do you find most productive to listen to while coding, Music while programming and more. Sadly a lot of these questions were closed as off-topic, etc. But (1) I don't think this question is off-topic and I think that a lot of programmers can benefit from it. (2) It's a real question. I really want to know what music you guys would recommend because music helps when I'm coding. It's sad that SO: Music to listen to while coding cannot be found and this isn't of much help. I hope this doesn't get closed. PS: I want to turn this into a community wiki, but I don't seem to know how. I'd appreciate any help. Thank you, all. In response to kirk.burleson's comment: In case the question isn't already clear, I'm asking for recommendations/opinions of music to listen to while coding. I would like to know what you listen to when you code so that I can try it too. I am running out of good "coding music" and this is a problem for me because good "coding music" helps me code better.

  Read the article

• Can't enable wireless lan on Fujitsu Siemens A1665G with Ubuntu 11.10 installed

  - by Theo

  I saw my old Notebook yesterday and wanted to make that work again. On Windows XP the wireless worked still fine. Then I installed new Ubuntu 11.10 32bit and I'm sadly not able to make the wireless enabled. [I replaced Win XP entirely] lspci lists following network: 08:0a.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) So after recommendation from this link I installed the b43 firmware module. iwconfig prints the following: wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associatd Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management: off As you can see, my wireless lan adapter is not turned on. sudo iwconfig wlan0 txpower auto Doesn't change anything. Then I tried to make it work with rfkill. rfkill list 0: phy0: Wirless LAN Soft blocked: no Hard blocked: yes sudo rfkill unblock all rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes remains the same. The question is now, how I could enable the hard blocked wireless LAN. There is no hardware switch for wlan integrated. However there is a button to change the state. I always thought this would be software sided, but it seems to make some hardware changes as well... The wireless LED is also not blinking (as it did on windows xp) I reset bios and searched for some settings in there, but it has only a few options and nothing to do with wireless settings, nothing works here.. At last I tried to install the acer hotkeys but I was not able to manage that. I installed the acerhkgui package, but in initializing progress, it was not able to compile acer hotkeys for my machine. There was a message that asm/linkage.h was not found while compiling. Do you have any ideas what I could do to make this hard blocked stuff disabled and my wireless card work? PS: I also tried sudo rm /dev/rfkill and a reboot to reinit that stuff... No success :(

  Read the article

• Search inside Xournal files (.xoj)

  - by Javad Sadeqzadeh

  I'm a big fan of Evernote, I use it regularly. However, it has a 60MB storage limit (although text files are not going to occupy much space, but the limitation concern still remains). Today, I installed Xournal, which has great features like annotating, nice background, free hand shapes and notes, save in PDF format, and many more. But the big problem is that as far as I've noticd, there is no intrinsic feature for seach inside the notes (created using Xournal with .xoj suffix). I used Catfish File Search application (which creates bash commands for full text search), but it couldn't help as well. Is there anyway to search inside a .xoj file at all? If so, it could be a suitable alternative to evernote, if you put your .xoj files on a cloud (which certainly offers you much more storage space than 60MB). If not, is there any other convenient app similar to Evernote, but with higher storage limit or without a limit? Somebody suggested Zim desktop wiki app, which looks great, but I'm nut sure if I could copy and paste everything there (a mixture of photos and tables and text with various formats and highlights), like what I do with Evernote. And a very useful tool I use is Evernote Web Clipper (browser extension). Of course, having a desktop client like Everpad is a plus, but not the absolute need. PS: I use pocket, so please do suggest that (it only preserve links (which might change over time) not the actual text). I also use google drive or docs, I don't like that for this purpose niether, it's too slow, doesn't have a browser extension and a desktop client. Thank you so much in advance.

  Read the article

• Mac OS needs Windows Live Writer &ndash; badly!

  - by digitaldias

  I recently bought a new  Macbook Pro (the 13” one) to dive into a new world of programming challenges as well as to get a more powerful netbook than my Packard Bell Dot which I’ve been using since last year. I’ve had immense pleasure using the netbook format and their small size in meetings (taking notes with XMind), surfing “anywhere”, and, of course blogging with windows live writer. So far the Mac is holding up, it’s sleek, responsive, and I’ve even begun looking at coding in Objective C with it, but in one arena, it is severely lacking: Blogging software. There is nothing that even comes close to Live Writer for getting your blog posts out. The few blogger applications that do exist on mac both look and feel medieval in comparison, AND some even cost money! It looks like some mac users actually install a virtual machine on their mac to run Windows XP just so they can use WLW. I’m not that extreme; instead, I’m hoping that the WLW team will write it’s awesome application as a Silverlight 4 app. That way, it would run on Mac and Windows (as a desktop app). I wonder if it will ever happen though…   PS: The image is of me, took it with the built-in camera on the mac and emailed it to the windows PC that I am writing on :)

  Read the article

• login takes long time

  - by Arkaprovo Bhattacharjee

  I am using Ubuntu 12.04 from past 12 days. In the beginning login was fast enough after I put the password it hardly takes 3 to 4 sec to enter in desktop, but now its taking like more that 40 sec to show desktop after entering password. whats the problem, is there any solution? P.S there is only two programs (psensor and jupiter) that starts automatically after login. boot.log fsck from util-linux 2.20.1 /dev/sda6: clean, 254544/3325952 files, 2133831/13285632 blocks * Stopping Userspace bootsplash[164G[ OK ] * Stopping Flush boot log to disk[164G[ OK ] * Starting mDNS/DNS-SD daemon[164G[ OK ] Skipping profile in /etc/apparmor.d/disable: usr.sbin.rsyslogd Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox * Starting bluetooth daemon[164G[ OK ] * Starting network connection manager[164G[ OK ] * Starting AppArmor profiles [170G [164G[ OK ] * Stopping System V initialisation compatibility[164G[ OK ] * Starting CUPS printing spooler/server[164G[ OK ] * Starting System V runlevel compatibility[164G[ OK ] * Starting Bumblebee supporting nVidia Optimus cards[164G[ OK ] * Starting LightDM Display Manager[164G[ OK ] * Starting save kernel messages[164G[ OK ] * Starting anac(h)ronistic cron[164G[ OK ] * Starting ACPI daemon[164G[ OK ] * Starting regular background program processing daemon[164G[ OK ] * Starting deferred execution scheduler[164G[ OK ] speech-dispatcher disabled; edit /etc/default/speech-dispatcher * Starting CPU interrupts balancing daemon[164G[ OK ]

  Read the article

• How do I access shared folders on Ubuntu server from Mac OS?

  - by Stephen

  I have an old dell desktop running ubuntu 11.04, I also have samba installed on it. I'm trying to access the shared folders on the Ubuntu machine from my Mac, so I go into 'Finder', click on 'Go' and 'Connect to Server'. I type in the ip address of the ubuntu machine smb://xxx.xxx.x.xx and click connect, I can then see the list of shared folders from the ubuntu machine so I know its making a connection. But when I access the 'Music' folder I get an error message stating: There was an error connecting to the server "xxx.xxx.x.xx". Check the server name or IP address, and try again. Any thoughts anyone ? EDIT I have a external hard drive attached to the server, and the folders I'm trying to access are located on that external hard drive. The location of the folder is /media/HD-CELU2/test, so I think the path from Finder should be smb://xxx.xxx.x.xx/media/HD-CELU2/test, but having tested this, I'm still not getting in. P.S. I'm using Samba as I have a Windows machine on my home network as well.

  Read the article

• Google Chrome not rendering webpages correctly

  - by sumit_gt

  I am facing some serious web page rendering issues with Chrome. It is more prominent during javascript based animations and stuff on websites like youtube. I have tried removing chrome using (sudo apt-get purge google-chrome-stable) and then reinstalling it. But the problems still persist. The same webpages work correctly on firefox on ubuntu and chrome on windows. The problem only shows up when I use chrome on ubuntu. I think the issue has started after I updated to the latest version of Chrome. I have used Chrome previously on this machine without any problems. I have attached a image that demonstrates the issue. What could possibly be the problem? PS: here's the output of lshw -c video: *-display description: VGA compatible controller product: Madison [Radeon HD 5000M Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:46 memory:e0000000-efffffff memory:f0020000-f003ffff ioport:d000(size=256) memory:f0000000-f001ffff Here's the output of lspci -nn: output of lspci -nn

  Read the article

• What are the maths behind 'Raiden 2' purple laser?

  - by Aybe

  The path of the laser is affected by user input and enemies present on the screen. Here is a video, at 5:00 minutes the laser in question is shown : Raiden II (PS) - 1 Loop Clear - Part 2 UPDATE Here is a test using Inkscape, ship is at bottom, the first 4 enemies are targeted by the plasma. There seems to be a sort of pattern. I moved the ship first, then the handle from it to form a 45° angle, then while trying to fit the curve I found a pattern of parallel handles and continued so until I reached the last enemy. Update, 5/26/2012 : I started an XNA project using beziers, there is still some work needed, will update the question next week. Stay tuned ! Update : 5/30/2012 : It really seems that they are using Bézier curves, I think I will be able to replicate/imitate a plasma of such grade. There are two new topics I discovered since last time : Arc length, Runge's phenomenon, first one should help in having a linear movement possible over a Bézier curve, second should help in optimizing the number of vertices. Next time I will put a video so you can see the progress 8-)

  Read the article

• How to disable "N" Wireless Mode RTL8192 (Thinkpad Edge 15 Core i5) in natty

  - by Gustavo Rubio

  I've seen many owners of thinkpad edges which are supossed to be linux-friendly having problems with wireless adapter. I've found several links inside askubuntu and in ubuntuforums which have a lot of work-arounds for those problems, mine seems to be wierd though. I use my laptop on both my office and at home. At home I have a router which is A/B/G and here at home the wireless connection works just fine, using a WEP key. But in work I have a B/G/N wireless router and it doesn't work, my guess is that this adapter works with N modes but somehow this is buggy in the bundled driver in natty. I've tried to disable the "N" mode in the router but that didn't work. Later I went to realtek website, downloaded their driver and compiled myself, kinda seems to work most of the time but sometimes some websites keep trying to load or load just parts of it and images start to look like their links are broken and so on, much like what you get when you were loading a page and suddenly the connection is lost. This problem, as I said, is only using the realtek driver from their website. Dmesg gives me this a lot of these: [ 5869.049454] rtl8192se_update_ratr_table: ratr_index=0 ratr_table=0x00000ff5 [ 5879.240563] DHCP pkt src port:68, dest port:67!! So I thougth I might as well switch back to the original driver which seems to work just fine on A/B/G wireless networks but not on N networks so if anybody knows how to disable that mode from within the driver please let us know :) Thanks in advance! PS: I do found a link to a similar question and it was answered but let me remind you I'm NOT using the intel version of wireless for my thinkpad but the realtek (RTL8192SvB)

  Read the article

• ArchBeat Link-o-Rama for November 20, 2012

  - by Bob Rhubart

  Oracle Utilities Application Framework V4.2.0.0.0 Released | Anthony Shorten Principal Product Manager Anthony Shorten shares an overview of the changes implemented in the new release. Towards Ultra-Reusability for ADF - Adaptive Bindings | Duncan Mills "The task flow mechanism embodies one of the key value propositions of the ADF Framework," says Duncan Mills. "However, what if we could do more? How could we make task flows even more re-usable than they are today?" As you might expect, Duncan has answers for those questions. Oracle BPM Process Accelerators and process excellence | Andrew Richards "Process Accelerators are ready-to-deploy solutions based on best practices to simplify process management requirements," says Capgemini's Andrew Richards. "They are considered to be 'product grade,' meaning they have been designed; engineered, documented and tested by Oracle themselves to a level that they can be deployed as-is for a solution to a problem or extended as appropriate for a particular scenario." Oracle SOA Suite 11g PS 5 introduces BPEL with conditional correlation for aggregation scenarios | Lucas Jellema An extensive, detailed technical post from Oracle ACE Director Lucas Jellema. Check Box Support in ADF Tree Table Different Levels | Andrejus Baranovskis Oracle ACE Director Andrejus Baranovskis updates last year's "ADF Tree - How to Autoselect/Deselect Checkbox" post with new information. As Boom Lures App Creators, Tough Part Is Making a Living Great New York Times article about mobile app develoment also touches on other significant IT issues. Thought for the Day "Building large applications is still really difficult. Making them serve an organisation well for many years is almost impossible." — Malcolm P. Atkinson Source: SoftwareQuotes.com

  Read the article

• How to blend multiple normal maps?

  - by János Turánszki

  I want to achieve a distortion effect which distorts the full screen. For that I spawn a couple of images with normal maps. I render their normal map part on some camera facing quads onto a rendertarget which is cleared with the color (127,127,255,255). This color means that there is no distortion whatsoever. Then I want to render some images like this one onto it: If I draw one somewhere on the screen, then it looks correct because it blends in seamlessly with the background (which is the same color that appears on the edges of this image). If I draw another one on top of it then it will no longer be a seamless transition. For this I created a blendstate in directX 11 that keeps the maximum of two colors, so it is now a seamless transition, but this way, the colors lower than 127 (0.5f normalized) will not contribute. I am not making a simulation and the effect looks quite convincing and nice for a game, but in my spare time I am thinking how I could achieve a nicer or a more correct effect with a blend state, maybe averaging the colors somehow? I I did it with a shader, I would add the colors and then I would normalize them, but I need to combine arbitrary number of images onto a rendertarget. This is my blend state now which blends them seamlessly but not correctly: D3D11_BLEND_DESC bd; bd.RenderTarget[0].BlendEnable=true; bd.RenderTarget[0].SrcBlend = D3D11_BLEND_SRC_ALPHA; bd.RenderTarget[0].DestBlend = D3D11_BLEND_INV_SRC_ALPHA; bd.RenderTarget[0].BlendOp = D3D11_BLEND_OP_MAX; bd.RenderTarget[0].SrcBlendAlpha = D3D11_BLEND_ONE; bd.RenderTarget[0].DestBlendAlpha = D3D11_BLEND_ZERO; bd.RenderTarget[0].BlendOpAlpha = D3D11_BLEND_OP_MAX; bd.RenderTarget[0].RenderTargetWriteMask = 0x0f; Is there any way of improving upon this? (PS. I considered rendering each one with a separate shader incementally on top of each other but that would consume a lot of render targets which is unacceptable)

  Read the article

• Is it relatively safe to install kernel from "Canonical Kernel Team ppa" than "Mainline"

  - by tijybba

  I already referred most of the questions stating Upgrade from Mainline Builds or Compiling from latest source or PPA and also concluded that it can cause breakage to Current stable installed system. My question is regarding the kernel builds from Canonical Kernel Team which i have subscribed in Ubuntu 12.04 64-bit , states This is the core kernel team as hired by Canonical. Do not use this team, use ubuntu-kernel-team instead. My stable kernel states 3.2.0-27.42 from Ubuntu repository , also i consider Canonical Kernel Team to be Official ,currently urging me to Upgrade 3.2.0-27.43 , so from the Odd numbered and through the PPA description it is categorized as Unstable. From this ,it can be said next stable release would be 3.2.0-27.44. Is upgrading to .43 version is stable enough to continue , since .44 will be provide by Ubuntu itself based on .43 version and so on. Though i can't expect a lot of Changes ,but does it provide new Improvements or just Bug Fixes since it is just a preceding Release. Also , apart from Ubuntu mainline kernel , is Canonical Kernel Team different. If so , in what development or contribution terms. Is the Ubuntu kernel developed by Two different teams or same team. P.S.: Just noticed that sudo apt-get update && sudo apt-get upgrade provides me upgrade to .43 kernel , which normally requires sudo apt-get dist-upgrade to upgrade to newer kernel available , unless it normally provides message like " Following packages were not upgraded..." , is it an error or an exception to this Canonical Kernel PPA.

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >