Search Results

Search found 4906 results on 197 pages for 'ssh tunnel'.

Page 88/197 | < Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >

  • Can't access shared drive when connecting over VPN

    - by evolvd
    I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

    Read the article

  • Why doesn't pppd over ssh work here? Why can't I kill pppd?

    - by Peter V. Mørch
    I'm trying to setup a simple ppp tunnel over ssh. It works on several machines just fine. But on one machine, pppd gets "stuck": > pgrep pppd | xargs ps up USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 4178 0.0 0.1 3020 1088 pts/1 Ds+ 05:28 0:00 /usr/sbin/pppd Any attempt to kill it (even sudo kill -9 4178) has no effect that I can see. strace -p 4178 also hangs similarly. After it has been started for a while, I start getting messages in dmesg like shown below. It is started like so from another machine: ssh -t root@server /usr/sbin/pppd passive noauth When I do this to one of the machines that work, the remote end's pppd spits out garbage/binary data to the console (as expected). When I do it to the one that fails, I get no output from pppd, but the ssh session eventually times out. If I instead ssh to the machine, and then run /usr/sbin/pppd passive noauth in a separate step I also get the expected binary output. I now have a couple of questions: What could be up with the one machine where pppd fails? I don't even know where to start looking... What could be the difference between ssh -t root@server /usr/sbin/pppd passive noauth in a single step and ssh root@server and /usr/sbin/pppd passive noauth in two steps? How can it be that I can't kill the process even with sudo kill -9? The only way I know is to reboot. (I've tried searching for something similar but didn't get anywhere so I'm sorry I don't have any more leads) Any ideas? The problem machine runs in debian on VMware "hardware" (as do the ones that work) and it exhibits the problem when cloned and on both debian lenny (original) and squeeze (after upgrade) dmesg entries: [ 1198.727248] INFO: task pppd:4178 blocked for more than 120 seconds. [ 1198.727507] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1198.727904] pppd D ece2dc9c 0 4178 4174 0x00000004 [ 1198.727908] 00000098 00000082 f2503520 ece2dc9c 0000b1e7 00000000 c148d1c0 c148d1c0 [ 1198.727913] f2a06100 f6e071c0 00000000 ece2dc18 f5cd07e0 00000000 ece2d400 ece2dc9d [ 1198.727918] 00c52300 ece2dcbc f67bfef8 ec98e480 f291cec0 00000000 c10cf5b0 c10dfd21 [ 1198.727923] Call Trace: [ 1198.727926] [<c10cf5b0>] ? nameidata_to_filp+0x37/0x41 [ 1198.727929] [<c10dfd21>] ? dput+0x21/0xb7 [ 1198.727932] [<c11cfecc>] ? tty_ldisc_ref_wait+0x5f/0x76 [ 1198.727935] [<c104de7a>] ? wake_up_bit+0x5c/0x5c [ 1198.727938] [<c11cb91b>] ? tty_ioctl+0x85f/0x8ba [ 1198.727941] [<c10fec18>] ? do_lock_file_wait+0x3d/0xd9 [ 1198.727944] [<c1162c97>] ? _copy_from_user+0x2b/0x102 [ 1198.727946] [<c11cb0bc>] ? tty_check_change+0xb9/0xb9 [ 1198.727949] [<c10dbeb7>] ? do_vfs_ioctl+0x485/0x4c7 [ 1198.727952] [<c10db59a>] ? do_fcntl+0x24f/0x3a2 [ 1198.727954] [<c10dbf3a>] ? sys_ioctl+0x41/0x58 [ 1198.727957] [<c12c6a1f>] ? sysenter_do_call+0x12/0x28 [ 1318.457225] INFO: task sshd:4174 blocked for more than 120 seconds. [ 1318.457500] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1318.457896] sshd D f25024cc 0 4174 2393 0x00000000 [ 1318.457901] 00000098 00000086 f2a06940 f25024cc 0000b246 00000000 c148d1c0 c148d1c0 [ 1318.457906] f2503520 f6e071c0 00000000 3f056585 0000000f ece2d4bc 3f056585 f2503520 [ 1318.457911] ec98bb38 ec98bbdc 00000000 00000000 00000000 c12c09b5 f2503520 c10327cb [ 1318.457916] Call Trace: [ 1318.457926] [<c12c09b5>] ? schedule_hrtimeout_range_clock+0x3c/0xd9 [ 1318.457931] [<c10327cb>] ? try_to_wake_up+0x13f/0x13f [ 1318.457935] [<c11cfecc>] ? tty_ldisc_ref_wait+0x5f/0x76 [ 1318.457940] [<c104de7a>] ? wake_up_bit+0x5c/0x5c [ 1318.457943] [<c11c9ad3>] ? tty_poll+0x32/0x5e [ 1318.457947] [<c10dd4d5>] ? do_select+0x2a1/0x42e [ 1318.457950] [<c10dcb83>] ? poll_freewait+0x69/0x69 [ 1318.457953] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457955] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457958] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457960] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457963] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457965] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457968] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457971] [<c10429c2>] ? lock_timer_base+0x19/0x35 [ 1318.457974] [<c1042eb5>] ? __mod_timer+0x10c/0x116 [ 1318.457977] [<c1042f89>] ? mod_timer+0x69/0x6e [ 1318.457981] [<c121325d>] ? sk_reset_timer+0xc/0x16 [ 1318.457984] [<c1252f57>] ? tcp_event_new_data_sent+0x66/0x6b [ 1318.457987] [<c1255b85>] ? tcp_write_xmit+0x7a7/0x86a [ 1318.457990] [<c121760d>] ? __alloc_skb+0x50/0xfd [ 1318.457994] [<c12c12bc>] ? _raw_spin_lock_bh+0x8/0x1e [ 1318.457996] [<c1212e98>] ? release_sock+0x10/0xc4 [ 1318.457999] [<c124b543>] ? tcp_sendmsg+0x6dd/0x7b7 [ 1318.458003] [<c1162c97>] ? _copy_from_user+0x2b/0x102 [ 1318.458006] [<c10dd7a0>] ? core_sys_select+0x13e/0x1c3 [ 1318.458009] [<c12102a3>] ? sock_aio_write+0xc0/0xd4 [ 1318.458012] [<c10d0655>] ? do_sync_write+0xa0/0xe4 [ 1318.458016] [<c10b141c>] ? handle_mm_fault+0x222/0x238 [ 1318.458019] [<c10f6096>] ? fsnotify+0x1de/0x1f9 [ 1318.458022] [<c10dd9e8>] ? sys_select+0x6e/0x8f [ 1318.458024] [<c10d105e>] ? sys_write+0x3c/0x63 [ 1318.458028] [<c12c6a1f>] ? sysenter_do_call+0x12/0x28

    Read the article

  • How to set up a linux user that can only access a repository via ssh?

    - by GJ
    I have a mercurial repository on a secure server, to which I want to grant secure access to an external user. I added for him a user account and publickey ssh authentication so that now he could push/pull changesets via ssh. My question is: how can I make this new user account completely disabled from doing anything or accessing any data on the server other than accessing the repository? E.g. he shouldn't even have the possibility to enter an interactive shell session. Thanks

    Read the article

  • How can I prevent OpenVPN Client from blocking inbound connections while a tunnel is connected?

    - by joshudson
    We have this machine that we RDP into for using OpenVPN. When a tunnel is connected, it is not possible to RDP into the machine. Should we get disconnected, this is a problem (machine is headless). How can I stop OpenVPN from blocking inbound RDP? I do not have access to the server configuration. If there's anything interesting on the client to check you'll have to tell me how to get at it. I eliminated the possibility of routing issue before asking the question. Only inbound connections cannot be opened. Outbound connections to LAN can be opened just fine. EDIT: Don't bother answering. The problem disappeared without any known changes being made.

    Read the article

  • How do I X forward a Windows application to a Linux system using ssh?

    - by triunenature
    Ok, so if I have two Linux Machines (A and B) and I have a program on one, and want to run it on be I do: user@LinuxA:~$ ssh -X LinuxB user@LinuxB:~$ programName (Displays on LinuxA machine) Ok same thing, WindowsA LinuxB (Program on Linux) Start Xming X Server on Windows Run Putty, use x11 port forward with :0.0 After connect to LinuxB, run program, it loads in Windows! Now here is the question, WindowsA LinuxB, (Program on Windows) Run Windows Program On Linux, using a windows resources. How to make it work? BTW, I know it can because years ago, I read a white paper on it, but never actually tested it out.

    Read the article

  • Cisco ASA: Allowing and Denying VPN Access based on membership to an AD group

    - by milkandtang
    I have a Cisco ASA 5505 connecting to an Active Directory server for VPN authentication. Usually we'd restrict this to a particular OU, but in this case users which need access are spread across multiple OUs. So, I'd like to use a group to specify which users have remote access. I've created the group and added the users, but I'm having trouble figuring out how to deny users which aren't in that group. Right now, if someone connects they get assigned the correct group policy "companynamera" if they are in that group, so the LDAP mapping is working. However, users who are not in that group still authenticate fine, and their group policy becomes the LDAP path of their first group, i.e. CN=Domain Users,CN=Users,DC=example,DC=com, and then are still allowed access. How do I add a filter so that I can map everything that isn't "companynamera" to no access? Config I'm using (with some stuff such as ACLs and mappings removed, since they are just noise here): gateway# show run : Saved : ASA Version 8.2(1) ! hostname gateway domain-name corp.company-name.com enable password gDZcqZ.aUC9ML0jK encrypted passwd gDZcqZ.aUC9ML0jK encrypted names name 192.168.0.2 dc5 description FTP Server name 192.168.0.5 dc2 description Everything server name 192.168.0.6 dc4 description File Server name 192.168.0.7 ts1 description Light Use Terminal Server name 192.168.0.8 ts2 description Heavy Use Terminal Server name 4.4.4.82 primary-frontier name 5.5.5.26 primary-eschelon name 172.21.18.5 dmz1 description Kerio Mail Server and FTP Server name 4.4.4.84 ts-frontier name 4.4.4.85 vpn-frontier name 5.5.5.28 ts-eschelon name 5.5.5.29 vpn-eschelon name 5.5.5.27 email-eschelon name 4.4.4.83 guest-frontier name 4.4.4.86 email-frontier dns-guard ! interface Vlan1 nameif inside security-level 100 ip address 192.168.0.254 255.255.255.0 ! interface Vlan2 description Frontier FiOS nameif outside security-level 0 ip address primary-frontier 255.255.255.0 ! interface Vlan3 description Eschelon T1 nameif backup security-level 0 ip address primary-eschelon 255.255.255.248 ! interface Vlan4 nameif dmz security-level 50 ip address 172.21.18.254 255.255.255.0 ! interface Vlan5 nameif guest security-level 25 ip address 172.21.19.254 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 switchport access vlan 3 ! interface Ethernet0/2 switchport access vlan 4 ! interface Ethernet0/3 switchport access vlan 5 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone PST -8 clock summer-time PDT recurring dns domain-lookup inside dns server-group DefaultDNS name-server dc2 domain-name corp.company-name.com same-security-traffic permit intra-interface access-list companyname_splitTunnelAcl standard permit 192.168.0.0 255.255.255.0 access-list companyname_splitTunnelAcl standard permit 172.21.18.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.20.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip any 172.21.18.0 255.255.255.0 access-list bypassingnat_dmz extended permit ip 172.21.18.0 255.255.255.0 192.168.0.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 12288 logging buffered warnings logging asdm notifications mtu inside 1500 mtu outside 1500 mtu backup 1500 mtu dmz 1500 mtu guest 1500 ip local pool VPNpool 172.21.20.50-172.21.20.59 mask 255.255.255.0 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface global (outside) 2 email-frontier global (outside) 3 guest-frontier global (backup) 1 interface global (dmz) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 2 dc5 255.255.255.255 nat (inside) 1 192.168.0.0 255.255.255.0 nat (dmz) 0 access-list bypassingnat_dmz nat (dmz) 2 dmz1 255.255.255.255 nat (dmz) 1 172.21.18.0 255.255.255.0 access-group outside_access_in in interface outside access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 4.4.4.1 1 track 1 route backup 0.0.0.0 0.0.0.0 5.5.5.25 254 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 ldap attribute-map RemoteAccessMap map-name memberOf IETF-Radius-Class map-value memberOf CN=RemoteAccess,CN=Users,DC=corp,DC=company-name,DC=com companynamera dynamic-access-policy-record DfltAccessPolicy aaa-server ActiveDirectory protocol ldap aaa-server ActiveDirectory (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft aaa-server ADRemoteAccess protocol ldap aaa-server ADRemoteAccess (inside) host dc2 ldap-base-dn dc=corp,dc=company-name,dc=com ldap-scope subtree ldap-login-password * ldap-login-dn cn=administrator,ou=Admins,dc=corp,dc=company-name,dc=com server-type microsoft ldap-attribute-map RemoteAccessMap aaa authentication enable console LOCAL aaa authentication ssh console LOCAL http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart sla monitor 123 type echo protocol ipIcmpEcho 4.4.4.1 interface outside num-packets 3 frequency 10 sla monitor schedule 123 life forever start-time now crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 ! track 1 rtr 123 reachability telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 5 ssh version 2 console timeout 0 management-access inside dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy companynamera internal group-policy companynamera attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com group-policy companyname internal group-policy companyname attributes wins-server value 192.168.0.5 dns-server value 192.168.0.5 vpn-tunnel-protocol IPSec password-storage enable split-tunnel-policy tunnelspecified split-tunnel-network-list value companyname_splitTunnelAcl default-domain value corp.company-name.com split-dns value corp.company-name.com username admin password IhpSqtN210ZsNaH. encrypted privilege 15 tunnel-group companyname type remote-access tunnel-group companyname general-attributes address-pool VPNpool authentication-server-group ActiveDirectory LOCAL default-group-policy companyname tunnel-group companyname ipsec-attributes pre-shared-key * tunnel-group companynamera type remote-access tunnel-group companynamera general-attributes address-pool VPNpool authentication-server-group ADRemoteAccess LOCAL default-group-policy companynamera tunnel-group companynamera ipsec-attributes pre-shared-key * ! class-map type inspect ftp match-all ftp-inspection-map class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect ftp ftp-inspection-map parameters class ftp-inspection-map policy-map type inspect dns migrated_dns_map_1 parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns migrated_dns_map_1 inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect ils inspect netbios inspect rsh inspect rtsp inspect skinny inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp inspect icmp inspect icmp error inspect esmtp inspect pptp ! service-policy global_policy global prompt hostname context Cryptochecksum:487525494a81c8176046fec475d17efe : end gateway# Thanks so much!

    Read the article

  • How can I have puppet deploy ssh keys for virtual users?

    - by Pheezy
    I am trying to get puppet to assign authorized ssh keys for virtual users but I keep getting the following error: err: Could not retrieve catalog: Could not parse for environment production: Syntax error at 'user'; expected '}' at /etc/puppet/modules/users/manifests/ssh_authorized_keys.pp:9 I believe my configuration are correct (listed below) but is there a syntax error or scoping issue I am missing? I would simply like to assign users to nodes and have those users automagically have their ssh keys installed. Is there maybe a better way to do this and I'm just overthinking it? # /etc/puppet/modules/users/virtual.pp class user::virtual { @user { "user": home => "/home/user", ensure => "present", groups => ["root","wheel"], uid => "8001", password => "SCRAMBLED", comment => "User", shell => "/bin/bash", managehome => "true", } # /etc/puppet/modules/users/manifests/ssh_authorized_keys.pp ssh_authorized_key { "user": ensure => "present", type => "ssh-dss", key => "AAAAB....", user => "user", } # /etc/puppet/modules/users/init.pp import "users.pp" import "ssh_authorized_keys.pp" class user::ops inherits user::virtual { realize( User["user"], ) } # /etc/puppet/manifests/modules.pp import "sudo" import "users" # /etc/puppet/manifests/nodes.pp node basenode { include sudo } node 'testbox' inherits basenode { include user::ops } # /etc/puppet/manifests/site.pp import "modules" import "nodes" # The filebucket option allows for file backups to the server filebucket { main: server => 'puppet' } # Set global defaults - including backing up all files to the main filebucket and adds a global path File { backup => main } Exec { path => "/usr/bin:/usr/sbin/:/bin:/sbin" }

    Read the article

  • scp error: "Permission denied (publickey). lost connection"

    - by Winston C. Yang
    I tried to scp an svn dump to savannah, but I got the following error at the end. Permission denied (publickey). lost connection The scp command and verbose output are below. Any ideas? [wcyang@be2-wireless-pittnet-60-37 ~]$ scp -v diffcolor-dump.bz2 [email protected]:/srv/download/diffcolor/ Executing: program /usr/bin/ssh host dl.sv.gnu.org, user wcyang, command scp -v -t /srv/download/diffcolor/ OpenSSH_5.2p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to dl.sv.gnu.org [140.186.70.73] port 22. debug1: Connection established. debug1: identity file /Users/wcyang/.ssh/identity type -1 debug1: identity file /Users/wcyang/.ssh/id_rsa type 1 debug1: identity file /Users/wcyang/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'dl.sv.gnu.org' is known and matches the RSA host key. debug1: Found key in /Users/wcyang/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /Users/wcyang/.ssh/identity debug1: Offering public key: /Users/wcyang/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Trying private key: /Users/wcyang/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). lost connection

    Read the article

  • Best IDE macro tools to combat the verbosity of Java syntax for someone with carpal tunnel?

    - by Carlsberg
    I have a bad case of carpal tunnel so I'm looking for an editor that would make my Java programming less painful (literally!). Does anyone have any recommendations for tools that you can add to Eclipse, Netbeans or other IDEs to produce some of the repetitive code that's common in Java syntax? Overall what would be the best code editor for this purpose? (I'm coding on Ubuntu, in case it matters).

    Read the article

  • GRE keepalive with Linux and RouterOS

    - by eri
    I have a Linux host and couple of routerboadrs. I created a GRE tunnel, but Linux does not answer keepalive packages. Then router mark gre connection as unreachable, so I cant send to Linux host from router subnet. If linux sends something into tunnel (ping, etc.) - RouterOS mark connection as reacheble. Second and next packages routed nicely until one minute idle (no traffic). Tunnel in linux a make in this way: remote=x.x.x.x dev=gre21 network=10.21.0.0/16 ip tunnel add ${dev} mode gre remote ${remote} ttl 255 ip addr add 172.16.1.1/24 peer 172.16.1.21 dev ${dev} ip link set ${dev} up ip route add ${network} dev ${dev} And ip l: 14: gre21: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1476 qdisc noqueue state UNKNOWN link/gre 0.0.0.0 peer 109.60.170.15 How to set state "running"? How to keep alive tunnel? Ping in cron?

    Read the article

  • How to send connection type (SSH|Telnet) info in Radius Access Requests on Cisco router?

    - by Gianni Costanzi
    I've configured the following on a cisco router: aaa authentication login default group radius local ! radius-server host x.x.x.x auth-port 1012 acct-port 1013 radius-server host y.y.y.y auth-port 1012 acct-port 1013 radius-server retransmit 1 radius-server timeout 3 radius-server key 7 xxxxxxxxx I'd like to be able to specify some radius options in order to add information about the type of connection for which a user is being authenticated, i.e. I'd like the radius server to receive in the Cisco Router's Radius Access Request information about the connection being SSH or Telnet.. I'd like to find something that automatically adds this info in the access request, without specific configurations on VTY lines dedicated to SSH and to Telnet. Any idea about that?

    Read the article

  • I just got a linode VPS a week ago and I've been flagged for SSH scanning...

    - by meder
    I got a 32-bit Debian VPS from http://linode.com and I really haven't done any sort of advanced configuration for securing it ( port 22; password enabled ). It seems somehow there is ssh scanning going on from my IP, I'm being flagged as this is against the TOS. I've been SSHing only from my home Comcast ISP which I run Linux on. Is this a common thing when getting a new vps? Are there any standard security configuration tips? I'm quite confused as to how my machine has been accused of this ssh scanning.

    Read the article

  • How can I view my video card's temperature via SSH?

    - by NT3RP
    I've finally managed to set up my two ATI Radeon 6950 video cards in my machine, but the cards can get quite hot. Based on the arrangement of my apartment, I want to be able to SSH into the machine an execute a command to find out the temperature. What I have tried so far is this... export DISPLAY=:0.0 sudo aticonfig --adapter=0 --od-gettemperature However, when I do that via SSH, I get the following error: ERROR - X needs to be running to perform ATI Overdrive(TM) commands If I turn on X forwarding when I remote into the machine, then it just seems to affect my local machine instead of the remote machine. Am I doing this correctly? Is there a better way to monitor my video card's temperature?

    Read the article

  • How can I use sudo when I logged in with a SSH key in PuTTY?

    - by Alex
    I know the title probably doesn't even make sense, but anyway. I downloaded PuTTY and set it up, and followed this tutorial to set up SSH keys so I don't have to input a user or password when logging in with SSH. I noticed that when I made a new user I used the --disabled-password parameter, since I wouldn't be needing it... but now when I give the user sudo powers I can't proceed as it asks me for the user's password, and I don't have one. What do I do?

    Read the article

  • public key always asking for password and keyphrase

    - by Andrew Atkinson
    I am trying to SSH from a NAS to a webserver using a public key. NAS user is 'root' and webserver user is 'backup' I have all permissions set correctly and when I debug the SSH connection I get: (last little bit of the debug) debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering DSA public key: /root/.ssh/id_dsa.pub debug1: Server accepts key: pkalg ssh-dss blen 433 debug1: key_parse_private_pem: PEM_read_PrivateKey failed debug1: read PEM private key done: type <unknown> Enter passphrase for key '/root/.ssh/id_dsa.pub': I am using the command: ssh -v -i /root/.ssh/id_dsa.pub [email protected] The fact that it is asking for a passphrase is a good sign surely, but I do not want it to prompt for this or a password (which comes afterwards if I press 'return' on the passphrase)

    Read the article

  • rsync to EC2: Identity file not accessible

    - by Richard
    I'm trying to rsync a file over to my EC2 instance: rsync -Paz --rsh "ssh -i ~/.ssh/myfile.pem" --rsync-path "sudo rsync" file.pdf [email protected]:/home/ubuntu/ This gives the following error message: Warning: Identity file ~/.ssh/myfile.pem not accessible: No such file or directory. [email protected]'s password: The pem file is definitely located at the path ~/.ssh/myfile.pem, though: vi ~/.ssh/myfile.pem shows me the file. If I remove the remote path from the very end of the rsync command: rsync -Paz --rsh "ssh -i ~/.ssh/myfile.pem" --rsync-path "sudo rsync" file.pdf [email protected] Then the command appears to work... building file list ... 1 file to consider file.pdf 41985 100% 8.79MB/s 0:00:00 (xfer#1, to-check=0/1) sent 41795 bytes received 42 bytes 83674.00 bytes/sec total size is 41985 speedup is 1.00 ...but when I go to the remote server, nothing has actually been transferred. What am I doing wrong?

    Read the article

  • Is there an SSL equivelent to an ssh agent?

    - by Matthew J Morrison
    Here is my situation: There are a number of developers who all need to have access to be able to install ruby gems and python eggs from a remote source. Currently, we have a server inside our firewall that hosts the gems and eggs. We now want the ability to be able to install things hosted on that server outside of our firewall. Since some of the gems and eggs that we host are proprietary I would like to somewhat lock access to that machine down, as unobtrusively as possible to the developers. My first thought was using something like ssh keys. So, I spent some time looking at SSL mutual authentication. I was able to get everything set up and working correctly, testing with curl, but the unfortunate thing was that I had to pass extra arguments to curl so it knows about the certificate, key and certificate authority. I was wondering if there is anything like the ssh agent that I can set up to provide that information automatically so that I can push the certificates and keys to the developer's machines so the developers don't have to log in or provide keys each time they try to install something. Another thing that I want to avoid is having to modify the 'gem' command and the 'pip' command to provide keys when they make the http connection. Any other suggestions that may solve this problem (not related to ssl mutual auth) are also welcome. EDIT: I've been continuing to research this and I came across stunnel. I think this may be what I'm looking for, any feedback regarding stunnel would also be great!

    Read the article

  • What are secure ways of sharing a server (ssh+LAMP) with friends?

    - by Bran the Blessed
    What is the best way to share a virtual server with friends? More precisely, I have the following assets: A virtual private server (Debian Lenny) with root access for myself, running... SSH apache2 mysql Some unused disk space Some friends in need of hosting The problem I would now like to do the following: Hosting one or several domains per friend My friends should have full access to their domains, including running PHP scripts, for example My friends should not be able to poke around in other directories The security of my server should not be compromised by faulty PHP scripts To clarify: I do trust my friends in the sense that they are not trying to do something evil with their access. I just do not trust the programs they are going to run. So, what are your recommendations for establishing such a scenario? Partial solution I already came up with the following plan: Add chrooted SSH users for my friends Add Apache vhosts per user (point the directories to subdirectories of the homedirectories, i.e. /home/alice/example.com, /home/bob/example.net, etc. But how can I enforce a chroot-like environment for the scripts they are running within these vhosts? Any pointers would be appreciated.

    Read the article

  • how can I give openvpn clients access to a dns server (bind9) that is located on the same machine as the openvpn server

    - by lacrosse1991
    I currently have a debian server that is running an openvpn server. I also have a dns server (bind9) that I would like give allow access to by the connected openvpn clients, but I am unsure as of how to do this, I already known how to send dns options to the clients using push "dhcp-option DNS x.x.x.x" but I am just unsure how give the clients access to the dns server that is located on the same machine as the vpn server, so if anyone could point me in the right direction I would really appreciate it. Also in case this would have anything to do with adding rules to iptables, this is my current configuration for iptables # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *nat :PREROUTING ACCEPT [3831842:462225238] :INPUT ACCEPT [3820049:461550908] :OUTPUT ACCEPT [1885011:139487044] :POSTROUTING ACCEPT [1883834:139415168] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 18 22:05:33 2012 # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *filter :INPUT ACCEPT [45799:10669929] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [45747:10335026] :fail2ban-apache - [0:0] :fail2ban-apache-myadmin - [0:0] :fail2ban-apache-noscript - [0:0] :fail2ban-ssh - [0:0] :fail2ban-ssh-ddos - [0:0] :fail2ban-webserver-w00tw00t - [0:0] -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-myadmin -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-webserver-w00tw00t -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-noscript -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh-ddos -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -i tun+ -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 3306 -j ACCEPT -A FORWARD -i tun+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A fail2ban-apache -j RETURN -A fail2ban-apache-myadmin -s 211.154.213.122/32 -j DROP -A fail2ban-apache-myadmin -s 201.170.229.96/32 -j DROP -A fail2ban-apache-myadmin -j RETURN -A fail2ban-apache-noscript -j RETURN -A fail2ban-ssh -s 76.9.59.66/32 -j DROP -A fail2ban-ssh -s 64.13.220.73/32 -j DROP -A fail2ban-ssh -s 203.69.139.179/32 -j DROP -A fail2ban-ssh -s 173.10.11.146/32 -j DROP -A fail2ban-ssh -j RETURN -A fail2ban-ssh-ddos -j RETURN -A fail2ban-webserver-w00tw00t -s 217.70.51.154/32 -j DROP -A fail2ban-webserver-w00tw00t -s 86.35.242.58/32 -j DROP -A fail2ban-webserver-w00tw00t -j RETURN COMMIT # Completed on Thu Oct 18 22:05:33 2012 also here is my openvpn server configuration port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt keepalive 10 120 comp-lzo user nobody group users persist-key persist-tun status /var/log/openvpn/openvpn-status.log verb 3 push "redirect-gateway def1" push "dhcp-option DNS 213.133.98.98" push "dhcp-option DNS 213.133.99.99" push "dhcp-option DNS 213.133.100.100" client-to-client

    Read the article

  • Facing error: "Could not open a connection to your authentication agent."; trying to add ssh-key.

    - by Kaustubh P
    I use ubuntu server 10.04. ssh-add /foo/cert.pem gave the following output Could not open a connection to your authentication agent. These are my running processes: ps -aux | grep ssh Warning: bad ps syntax, perhaps a bogus '-'? See http://procps.sf.net/faq.html root 1523 0.0 0.0 49260 632 ? Ss Dec25 0:00 /usr/sbin/sshd root 10023 0.0 0.3 141304 6012 ? Ss 12:58 0:00 sshd: padmin [priv] padmin 10117 0.0 0.1 141304 2400 ? S 12:58 0:00 sshd: padmin@pts/1 padmin 11867 0.0 0.0 7628 964 pts/1 S+ 13:06 0:00 grep --color=auto ssh root 31041 0.0 0.3 141264 5884 ? Ss 11:24 0:00 sshd: padmin [priv] padmin 31138 0.0 0.1 141264 2312 ? S 11:25 0:00 sshd: padmin@pts/0 root 31382 0.0 0.3 139240 5844 ? Ss 11:26 0:00 sshd: padmin [priv] padmin 31475 0.0 0.1 139372 2488 ? S 11:27 0:00 sshd: padmin@notty padmin 31476 0.0 0.0 12468 964 ? Ss 11:27 0:00 /usr/lib/openssh/sftp-server These are my environment variables: $ env | grep SSH SSH_CLIENT=192.168.1.13 42626 22 SSH_TTY=/dev/pts/1 SSH_CONNECTION=192.168.1.13 42626 192.168.1.2 22 What is wrong? Why cant I add any identities? Thanks.

    Read the article

  • Can I easily use a VPN to duplicate SSH Tunneling functionality?

    - by Steve V.
    Right now, when I want to use an unsecured wireless connection with my (Linux) laptop, I secure my connection using a variation of the method provided here. However, to the best of my knowledge, the (non-jailbroken) iPad does not allow applications to tunnel traffic through local ports. However, it does seem to allow certain VPN traffic. I have never set up, or even used, a VPN before. I'm looking for confirmation that I'm not barking up the wrong tree before I invest significant effort into setting up my own VPN server. If I want to secure my wireless iPad traffic over an unsecure wireless connection, would I be on the right track by looking at a VPN?

    Read the article

< Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >