Search Results

Search found 4906 results on 197 pages for 'ssh tunnel'.

Page 92/197 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Port forwarding (portmap) works only locally

  - by Tag Wint

  There are four hosts hostA winXP hostB Win2003 hostC Linux RHEL hostD Linux RHEL hostA cannot connect to C and D directly, but B can hostA connects to hostB using VPN hostB and hostC belong to the same subnet1 hostD is in subnet2 From hostA I need to connect to hostC and hostD by SSH. Now I can do it as follows: 1.connecting from hostA to hostB by RDP logon and there: 2.start putty client. I'd like to omit step 1 and connect from A to C and D directly On hostB I have admin acoount and configure port forwarding as follows: netsh interface portproxy add v4tov4 listenport=N1 connectaddress=hostC_IP connectport=N2 netsh interface portproxy add v4tov4 listenport=N3 connectaddress=hostD_IP connectport=N2 netsh interface portproxy show all: Listen on IPv4: Connect to IPv4: Address Port Address Port --------------- ---------- --------------- ---------- * N1 hostC_IP N2 * N3 hostD_IP N2 Now from hostB I can connect to either C and D: ssh localhost:N1 ssh localhost:N3 from hostA ssh hostB:N1 works too, but ssh hostB:N3 DON'T I guess the reason might be different subnets, still have no idea how to fix it. What should I do?

  Read the article

• My Ubuntu VPS was wiped

  - by Lucas806

  Someone gained access into my Ubuntu VPS via SSH, they entered rm -Rf / which wiped it and now I can't access it via SSH or SFTP. On SFTP I get the the following error: Error: Connection timed out Error: Could not connect to server And then on SSH, I try to connect to my VPS IP on Port 22, it doesn't come up with anything for ages (it should come up asking for a username) and then a op-up appears saying: Network Error: Connection timed out. Is it possible to fix this, if so, how?

  Read the article

• Trouble with site-to-site OpenVPN & pfSense not passing traffic

  - by JohnCC

  I'm trying to get an OpenVPN tunnel going on pfSense 1.2.3-RELEASE running on embedded routers. I have a local LAN 10.34.43.0/254. The remote LAN is 10.200.1.0/24. The local pfSense is configured as the client, and the remote is configured as the server. My OpenVPN tunnel is using the IP range 10.99.89.0/24 internally. There are also some additional LANs on the remote side routed through the tunnel, but the issue is not with those since my connectivity fails before that point in the chain. The tunnel comes up fine and the logs look healthy. What I find is this:- I can ping and telnet to the remote LAN and the additional remote LANs from the local pfSense box's shell. I cannot ping or telnet to any remote LANs from the local network. I cannot ping or telnet to the local network from the remote LAN or the remote pfSense box's shell. If I tcpdump the tun interfaces on both sides and ping from the local LAN, I see the packets hit the tunnel locally, but they do not appear on the remote side (nor do they appear on the remote LAN interface if I tcpdump that). If I tcpdump the tun interfaces on both sides and ping from the local pfSense shell, I see the packets hit the tunnel locally, and exit the remote side. I can also tcpdump the remote LAN interface and see them pass there too. If I tcpdump the tun interfaces on both sides and ping from the remote pfSense shell, I see the packets hit the remote tun but they do not emerge from the local one. Here is the config file the remote side is using:- #user nobody #group nobody daemon keepalive 10 60 ping-timer-rem persist-tun persist-key dev tun proto udp cipher BF-CBC up /etc/rc.filter_configure down /etc/rc.filter_configure server 10.99.89.0 255.255.255.0 client-config-dir /var/etc/openvpn_csc push "route 10.200.1.0 255.255.255.0" lport <port> route 10.34.43.0 255.255.255.0 ca /var/etc/openvpn_server0.ca cert /var/etc/openvpn_server0.cert key /var/etc/openvpn_server0.key dh /var/etc/openvpn_server0.dh comp-lzo push "route 205.217.5.128 255.255.255.224" push "route 205.217.5.64 255.255.255.224" push "route 165.193.147.128 255.255.255.224" push "route 165.193.147.32 255.255.255.240" push "route 192.168.1.16 255.255.255.240" push "route 192.168.2.16 255.255.255.240" Here is the local config:- writepid /var/run/openvpn_client0.pid #user nobody #group nobody daemon keepalive 10 60 ping-timer-rem persist-tun persist-key dev tun proto udp cipher BF-CBC up /etc/rc.filter_configure down /etc/rc.filter_configure remote <host> <port> client lport 1194 ifconfig 10.99.89.2 10.99.89.1 ca /var/etc/openvpn_client0.ca cert /var/etc/openvpn_client0.cert key /var/etc/openvpn_client0.key comp-lzo You can see the relevant parts of the routing tables extracted from pfSense here http://pastie.org/5365800 The local firewall permits all ICMP from the LAN, and my PC is allowed everything to anywhere. The remote firewall treats its LAN as trusted and permits all traffic on that interface. Can anyone suggest why this is not working, and what I could try next?

  Read the article

• ASA 5505 stops local internet when connected to VPN

  - by g18c

  Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

  Read the article

• can't find port 22 traffic under VirtualBox

  - by telliott99

  I'm trying to learn to use tcpdump. I thought I'd eavesdrop on my ssh login. The setup is a bit unusual, I have OS X Lion running VirtualBox, with Ubuntu running in the VM. I have ssh enabled and can login from OS X normally: > ssh -p 22 10.0.1.2 -l telliott Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-17-generic i686) * Documentation: https://help.ubuntu.com/ 0 packages can be updated. 0 updates are security updates. Last login: Sat Mar 31 19:54:36 2012 from toms-mac-mini.local telliott@U32:~$ logout Connection to 10.0.1.2 closed. > I have not obfuscated the ssh port on Ubuntu. From OS X, stroke gives what I expect: > ./stroke 10.0.1.2 22 22 Port Scanning host: 10.0.1.2 Open TCP Port: 22 ssh So from OS X I do: > sudo tcpdump -i en1 -v port 22 Password: tcpdump: listening on en1, link-type EN10MB (Ethernet), capture size 65535 bytes Then I login from OS X to Ubuntu using ssh, but I see nothing with tcpdump. Here is ifconfig from Ubuntu: telliott@U32:~$ ifconfig eth1 Link encap:Ethernet HWaddr 08:00:27:d7:ba:0e inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fed7:ba0e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:799 errors:0 dropped:0 overruns:0 frame:0 TX packets:465 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:96863 (96.8 KB) TX bytes:68638 (68.6 KB) Where are the packets I was hoping to see? Thanks for any help.

  Read the article

• netstat on fresh install of Solaris 10 update 9

  - by cjavapro

  I am attempting to decipher the below output bash-3.00$ netstat -a UDP: IPv4 Local Address Remote Address State -------------------- -------------------- ---------- *.sunrpc Idle *.* Unbound *.32771 Idle TCP: IPv4 Local Address Remote Address Swind Send-Q Rwind Recv-Q State -------------------- -------------------- ----- ------ ----- ------ ----------- *.* *.* 0 0 49152 0 IDLE *.sunrpc *.* 0 0 49152 0 LISTEN *.* *.* 0 0 49152 0 IDLE localhost.5987 *.* 0 0 49152 0 LISTEN localhost.898 *.* 0 0 49152 0 LISTEN localhost.32771 *.* 0 0 49152 0 LISTEN localhost.5988 *.* 0 0 49152 0 LISTEN localhost.32772 *.* 0 0 49152 0 LISTEN *.ssh *.* 0 0 49152 0 LISTEN *.32785 *.* 0 0 49152 0 BOUND localhost.6788 *.* 0 0 49152 0 LISTEN localhost.6789 *.* 0 0 49152 0 LISTEN localhost.32782 *.* 0 0 49152 0 LISTEN localhost.smtp *.* 0 0 49152 0 LISTEN localhost.submission *.* 0 0 49152 0 LISTEN server-host-name.ssh pc-host-name.51269 64868 51 49640 0 ESTABLISHED TCP: IPv6 Local Address Remote Address Swind Send-Q Rwind Recv-Q State If --------------------------------- --------------------------------- ----- ------ ----- ------ ----------- ----- *.* *.* 0 0 49152 0 IDLE *.ssh *.* 0 0 49152 0 LISTEN SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED Active UNIX domain sockets Address Type Vnode Conn Local Addr Remote Addr ffffffff84e25ab8 stream-ord ffffffff8569c740 00000000 /var/run/.inetd.uds bash-3.00$ It looks to me like we have the following items UDP IPv4 Open ports sunrpc, 32771 Question 1: What is *.* Unbound? TCP IPv4 Open ports sunrpc, ssh 10 ports open only for localhost The open ssh connection from my PC Question 2: What is *.32785 *.* 0 0 49152 0 BOUND? Question 3: What is *.* *.* 0 0 49152 0 IDLE? (shows up twice) IPv6 Open port ssh Question 3: What is *.* *.* 0 0 49152 0 IDLE? Question 4: What is SCTP? Question 5: What is Active UNIX domain sockets

  Read the article

• git post-receive hook throws "command not found" error but seems to run properly and no errors when run manually

  - by Ben

  I have a post-receive hook that runs on a central git repository set up with gitolite to trigger a git pull on a staging server. It seems to work properly, but throws a "command not found" error when it is run. I am trying to track down the source of the error, but have not had any luck. Running the same commands manually does not produce an error. The error changes depending on what was done in the commit that is being pushed to the central repository. For instance, if 'git rm ' was committed and pushed to the central repo the error message will be "remote: hooks/post-receive: line 16: Removed: command not found" and if 'git add ' was committed and pushed to the central repo the error message will be "remote: hooks/post-receive: line 16: Merge: command not found". In either case the 'git pull' run on the staging server works correctly despite the error message. Here is the post-receive script: #!/bin/bash # # This script is triggered by a push to the local git repository. It will # ssh into a remote server and perform a git pull. # # The SSH_USER must be able to log into the remote server with a # passphrase-less SSH key *AND* be able to do a git pull without a passphrase. # # The command to actually perform the pull request on the remost server comes # from the ~/.ssh/authorized_keys file on the REMOTE_HOST and is triggered # by the ssh login. SSH_USER="remoteuser" REMOTE_HOST="staging.server.com" `ssh $SSH_USER@$REMOTE_HOST` # This is line 16 echo "Done!" The command that does the git pull on the staging server is in the ssh user's ~/.ssh/authorized_keys file and is: command="cd /var/www/staging_site; git pull",no-port-forwarding,no-X11-forwarding,no-agent-forwarding, ssh-rsa AAAAB3NzaC1yc2EAAAABIwAA... (the rest of the public key) This is the actual output from removing a file from my local repo, committing it locally, and pushing it to the central git repo: ben@tamarack:~/thejibe/testing/web$ git rm ./testing rm 'testing' ben@tamarack:~/thejibe/testing/web$ git commit -a -m "Remove testing file" [master bb96e13] Remove testing file 1 files changed, 0 insertions(+), 5 deletions(-) delete mode 100644 testing ben@tamarack:~/thejibe/testing/web$ git push Counting objects: 3, done. Delta compression using up to 2 threads. Compressing objects: 100% (2/2), done. Writing objects: 100% (2/2), 221 bytes, done. Total 2 (delta 1), reused 0 (delta 0) remote: From [email protected]:testing remote: aa72ad9..bb96e13 master -> origin/master remote: hooks/post-receive: line 16: Removed: command not found # The error msg remote: Done! To [email protected]:testing aa72ad9..bb96e13 master -> master ben@tamarack:~/thejibe/testing/web$ As you can see the post-receive script gets to the echo "Done!" line and when I look on the staging server the git pull has been successfully run, but there's still that nagging error message. Any suggestions on where to look for the source of the error message would be greatly appreciated. I'm tempted to redirect stderr to /dev/null but would prefer to know what the problem is.

  Read the article

• git post-receive hook throws "command not found" error but seems to run properly and no errors when run manually

  - by Ben

  I have a post-receive hook that runs on a central git repository set up with gitolite to trigger a git pull on a staging server. It seems to work properly, but throws a "command not found" error when it is run. I am trying to track down the source of the error, but have not had any luck. Running the same commands manually does not produce an error. The error changes depending on what was done in the commit that is being pushed to the central repository. For instance, if 'git rm ' was committed and pushed to the central repo the error message will be "remote: hooks/post-receive: line 16: Removed: command not found" and if 'git add ' was committed and pushed to the central repo the error message will be "remote: hooks/post-receive: line 16: Merge: command not found". In either case the 'git pull' run on the staging server works correctly despite the error message. Here is the post-receive script: #!/bin/bash # # This script is triggered by a push to the local git repository. It will # ssh into a remote server and perform a git pull. # # The SSH_USER must be able to log into the remote server with a # passphrase-less SSH key *AND* be able to do a git pull without a passphrase. # # The command to actually perform the pull request on the remost server comes # from the ~/.ssh/authorized_keys file on the REMOTE_HOST and is triggered # by the ssh login. SSH_USER="remoteuser" REMOTE_HOST="staging.server.com" `ssh $SSH_USER@$REMOTE_HOST` # This is line 16 echo "Done!" The command that does the git pull on the staging server is in the ssh user's ~/.ssh/authorized_keys file and is: command="cd /var/www/staging_site; git pull",no-port-forwarding,no-X11-forwarding,no-agent-forwarding, ssh-rsa AAAAB3NzaC1yc2EAAAABIwAA... (the rest of the public key) This is the actual output from removing a file from my local repo, committing it locally, and pushing it to the central git repo: ben@tamarack:~/thejibe/testing/web$ git rm ./testing rm 'testing' ben@tamarack:~/thejibe/testing/web$ git commit -a -m "Remove testing file" [master bb96e13] Remove testing file 1 files changed, 0 insertions(+), 5 deletions(-) delete mode 100644 testing ben@tamarack:~/thejibe/testing/web$ git push Counting objects: 3, done. Delta compression using up to 2 threads. Compressing objects: 100% (2/2), done. Writing objects: 100% (2/2), 221 bytes, done. Total 2 (delta 1), reused 0 (delta 0) remote: From [email protected]:testing remote: aa72ad9..bb96e13 master -> origin/master remote: hooks/post-receive: line 16: Removed: command not found # The error msg remote: Done! To [email protected]:testing aa72ad9..bb96e13 master -> master ben@tamarack:~/thejibe/testing/web$ As you can see the post-receive script gets to the echo "Done!" line and when I look on the staging server the git pull has been successfully run, but there's still that nagging error message. Any suggestions on where to look for the source of the error message would be greatly appreciated. I'm tempted to redirect stderr to /dev/null but would prefer to know what the problem is.

  Read the article

• Multiple authoritative DNS server on same IPv4 address

  - by Adrien Clerc

  I'd like to maintain a DNS tunnel on my self-hosted server at example.com. I also have a DNS server on it, which serves everything for example.com. I'm currently using dns2tcp for DNS tunneling, on the domain tunnel.example.com. NSD3 is used for serving authoritative zones, because it is both simple and secure. However, I have only one public IPv4 address, which means that NSD and dns2tcp can't listen on the same IP/port. So I'm currently using PowerDNS Recursor using the forward-zones parameter like this: forward-zones-recurse=tunnel.example.com=1.2.3.4:5354 forward-zones=example.com=1.2.3.4:5353 This enables request for authoritative zone to be asked to the correct server, as well as for tunnel requests. NSD is listening on port 5353 and dns2tcp on port 5354. However, this is bad, because the recursor needs to be open. And it actually answers to any recursive query. Do you have any solution for that? I really prefer a solution that doesn't involve setting up BIND, but if you are in the mood to convince me, don't hesitate to do so ;) EDIT: I change the title to be clearer.

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• NETKEY IPsec and ARP

  - by Shawn J. Goff

  I'm wondering if I have the correct routing setup for an IPsec tunnel. I have control over the IPsec endpoints and the hosts connected to one side. These hosts are connecting to the tunnel so that they have access to the network on the other side of what I will call the IPsec server. I don't have control of the network upstream of this server. Normally, the IPsec server will not respond to ARP requests for the hosts on the other side of the tunnel. So when a packet arrives for one of my hosts the server gets ARP requests, but the upstream router gets no response, and cannot construct the ethernet frame to send me the packets. If I was using one of the swan stacks, I would have a separate interface, and I'd probably just need to turn on proxyarp, but I'm using NETKEY, which doesn't use a separate interface for the tunnel. To solve the problem for now, I have added an eth0.5 vlan to the IPsec server, turned on proxyarp for that interface, and added all routes my hosts addresses to that interface so that it will respond to those ARP requests (and will therefore get relevant packets routed to it). This works, but it feels wrong. What is the correct way to get the upstream router to send me the traffic for these hosts?

  Read the article

• PFSense VPN Routing

  - by SvrGuy

  We use PFSense firewalls at three installations with the following LAN networks: 1.) Datacenter #1: 10.0.0.0/16 2.) Datacenter #2: 10.1.0.0/16 3.) HQ: 10.2.0.0/16 All of these locations are linked via an IPSEC tunnel that works properly. Hosts in any of the above networks can communicate with hosts in any other of the above networks. Now, for our laptops etc. we established a road warrior network 10.3.0.0/16 and have implemented OpenVPN to link the laptops etc. to Datacenter #1. This works great too, so our laptops can connect and communicate with any host in Datacenter #1 (anything on 10.0.0.0/16) The problem is the laptops can't communicate with any hosts that Datacenter #1 can reach by its IPSEC tunnel to Datacenter #2 (and/or the HQ for that matter). Does anyone know what to do configuration wise on the PFSense box in Datacenter #1 to configure to route packets received on the OpenVPN tunnel to Datacenter #2 over the IPSEC tunnel? It could be a setting on the OpenVPN or some sort of static route or some such. Any ideas?

  Read the article

• Cisco ASA dropping IPsec VPN between istself and CentOS server

  - by sebelk

  Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

  Read the article

• IP Phone over VPN - one way calls unless default route?

  - by dannymcc

  I have come across a strange problem with our VPN and BCM 50 (Nortel/Avaya) phone system. As you can tell by my other questions I have been doing some work on setting a VPN up from one location to another and it's all working well. With one exception. We have an IP phone that is connected at the remote location, straight to a router which has a VPN tunnel to our main practice. The phone works mostly, but every few calls it turns into a one way call. As in, the caller (from the remote phone) can't hear the receiver- but the receiver can hear the caller. This is fixed by setting the VPN tunnel to be the default route for all traffic. The problem with fixing it that way is that all traffic then goes through the tunnel which slows internet access etc. down considerably. The router is set to send the following over the VPN: 192.168.1.0/24 192.168.2.0/24 192.168.4.0/24 The IP of the remote location is: 192.168.3.0/24 The remote router (where the phone is) is a Draytek 2830n, and the local router (at the main practice) is a Draytek 2820. We are using an IPSec tunnel with AES encryption <- as a result of a previous answer pointing to the incompatibility in the hardware encryption. Any advice would be appreciated!

  Read the article

• Backup Exec 10 - Network connection to the remote agent has been lost

  - by jherlitz

  Okay, so I have 4 remote offices, all running off of a 3mb ethernet connection. Two sites are part of a WAN and 2 sites are using 3mb connections over a site to site tunnel. I am using Backup Exec 2010, I have the remote agent installed on all the remote servers. For the past few weeks now, on the two sites running over the site to site tunnel have been failing with the following error message now. "The network connection to the Backup Exec Remote Agent has been lost. Check for network errors" We used to be on a DSL connection site to site tunnel, now we changed to the 3mb ethernet connection using site to site tunnel. I have to find out, has it been failing ever since we changed, or just recently. Backup exec support is telling me it is a network issue. My communication or connection to the server is solid, we don't have any issues, or outages. So I am baffled on why this continues to fail. And why just those two sites.. Any advice?

  Read the article

• IPSec VPN using ZyWALL IPSec VPN Client: unable to connect from some providers

  - by Reshi

  I'm trying to configure an IPSec VPN to one company from my home. The company has SANET internet service provider. I was able to create a VPN connection from another company that has the same internet service provider. The problem begins when I'm trying to connect from another ISP like Orange or Telekom. Here is the log from ZyWall: 20120816 10:06:18:359 Default (SA Gateway-P1) SEND phase 1 Main Mode [SA] [VID] [VID] [VID] [VID] [VID] 20120816 10:06:18:375 Default (SA Gateway-P1) RECV phase 1 Main Mode [SA] [VID] [VID] [VID] [VID] [VID] [VID] [VID] [VID] 20120816 10:06:18:390 Default (SA Gateway-P1) SEND phase 1 Main Mode [KEY_EXCH] [NONCE] [NAT_D] [NAT_D] 20120816 10:06:18:718 Default (SA Gateway-P1) RECV phase 1 Main Mode [KEY_EXCH] [NONCE] [NAT_D] [NAT_D] 20120816 10:06:18:734 Default (SA Gateway-P1) SEND phase 1 Main Mode [HASH] [ID] 20120816 10:06:18:750 Default (SA Gateway-P1) RECV phase 1 Main Mode [HASH] [ID] 20120816 10:06:18:750 Default phase 1 done: initiator id [email protected], responder id 111.112.113.114 20120816 10:06:18:765 Default (SA Gateway-Tunnel-P2) SEND phase 2 Quick Mode [HASH] [SA] [KEY_EXCH] [NONCE] [ID] [ID] 20120816 10:06:18:953 Default (SA Gateway-Tunnel-P2) RECV phase 2 Quick Mode [HASH] [SA] [KEY_EXCH] [NONCE] [ID] [ID] 20120816 10:06:18:953 Default (SA Gateway-Tunnel-P2) SEND phase 2 Quick Mode [HASH] 20120816 10:06:48:968 Default (SA Gateway-P1) SEND Informational [HASH] [NOTIFY] type DPD_R_U_THERE 20120816 10:06:48:984 Default (SA Gateway-P1) RECV Informational [HASH] [NOTIFY] type DPD_R_U_THERE_ACK ZyWall informs me that the tunnel was opened. But I can't ping or access any computer in the network. My configuration at home: ISP: Orange Optical connection Terminal: GPON OPTICAL NETWORK TERMINAL G-25E Router: TPLink TL-WR941N --> SPI Firewall Enabled --> VPN - IPSEC Passthrough Enabled I was wondering if the problem could not be on ISP side (that he blocks somehow this connection because in SANET ISP it worked fine) or even in my terminal or router. What could I check? Where could be the problem ?

  Read the article

• PFSence VPN Routing

  - by SvrGuy

  We use PFSense firewalls at three installations with the following LAN networks: 1.) Datacenter #1: 10.0.0.0/16 2.) Datacenter #2: 10.1.0.0/16 3.) HQ: 10.2.0.0/16 All of these locations are linked via an IPSEC tunnel that works properly. Hosts in any of the above networks can communicate with hosts in any other of the above networks. Now, for our laptops etc. we established a road warrior network 10.3.0.0/16 and have implemented OpenVPN to link the laptops etc. to Datacenter #1. This works great too, so our laptops can connect and communicate with any host in Datacenter #1 (anything on 10.0.0.0/16) The problem is the laptops can't communicate with any hosts that Datacenter #1 can reach by its IPSEC tunnel to Datacenter #2 (and/or the HQ for that matter). Does anyone know what to do configuration wise on the PFSense box in Datacenter #1 to configure to route packets received on the OpenVPN tunnel to Datacenter #2 over the IPSEC tunnel? It could be a setting on the OpenVPN or some sort of static route or some such. Any ideas?

  Read the article

• How to manage eclipse project on remote computer; ssh, ftp?

  - by Kirzilla

  Hello, Usually I'm creating project work space on my localhost (win). As soon as my code is tested I'm committing it into repository. But some days ago I've faced a little difficulty. My customer want me to write code right on his server because he have some handmade binaries working only on his machine (solaris). I really don't know what to do. I've tried Eclipse plugin for connecting to remote servers, but I'm still unable to create remote project. Any ideas? PS: Sorry for my English :) Thank you.

  Read the article

• Why won't the following Clojure code tail a file via ssh?

  - by Zubair

  The following code never manages to tail a file. It simply hangs waiting for reader input. Has anyone tried anything similar? (def output (ref [] )) (import 'ch.ethz.ssh2.Connection) (import 'ch.ethz.ssh2.Session) (import 'ch.ethz.ssh2.StreamGobbler) (import 'java.lang.StringBuilder) (import 'java.io.InputStream) (import 'java.io.BufferedReader) (import 'java.io.InputStreamReader) (let [connection (new Connection "hostname")] (. connection connect) (let [ok (. connection authenticateWithPassword "username" "password" ) session (. connection openSession )] (. session execCommand "tail -f filename.txt") (let [sb (StringBuilder.) stdout (StreamGobbler. (. session getStdout)) br (BufferedReader. (InputStreamReader. stdout)) ] (future (loop [line2 (. br readLine)] (if (= line2 nil) nil (do (dosync (ref-set output (conj @output line2))) (recur (. br readLine)))) ) ) ) ) )

  Read the article

• .net compliant version control system that can be installed on a shared hosting (with no SSH/root Access)

  - by Farshid

  I searched a lot in SO and other websites for a version control system that can be installed on a shared windows hosting that lets me create repositories for putting my project files on it and supply me with version control facilities but I did not find one. I looked to see whether I can install git, Mercurial or TFS in a shared hosting and I did not found any answer. I want to know if you know any system that can be installed on a shared windows hosting and please tell your recommendations if you have had an experience before.

  Read the article

• Can anyone recommend a java FOSS server that does all the typical protocols (ssh etc).

  - by mP

  I would like to add the ability for users to telnet into my app where by they can type in commands etc. I would like a simple Java Telnet server whereby i can provide the authentication strategy.

  Read the article

• OpenSwan IPsec connection drops after 30 seconds

  - by drcore

  I'm trying to connection from my Linux Mint 16 box to a CloudStack server. Building up the connection works (pings work across the tunnel). However 30 seconds later the IPsec tunnel gets terminated out of the blue. What could cause this consistent behaviour and how to fix it? The tunnel is setup using OpenSwan (U2.6.38/K(no kernel code presently loaded)) with the L2TP IPsec VPN manager from Werner Jaeger 1.0.9. The client is behind a NAT'ed router and the server is on public IP (CloudStack 4.2) Running ipsec verify complains about IPsec support in kernel. Not sure if this is a problem as the connection is being build up: Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K(no kernel code presently loaded) Checking for IPsec support in kernel [FAILED] SAref kernel support [N/A] Checking that pluto is running [FAILED] whack: Pluto is not running (no "/var/run/pluto/pluto.ctl") Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] Tunnel config: version 2.0 # conforms to second version of ipsec.conf specification config setup # plutodebug="parsing emitting control private" plutodebug=none strictcrlpolicy=no nat_traversal=yes interfaces=%defaultroute oe=off # which IPsec stack to use. netkey,klips,mast,auto or none protostack=netkey conn %default keyingtries=3 pfs=no rekey=yes type=transport left=%defaultroute leftprotoport=17/1701 rightprotoport=17/1701 conn Tunnel1 authby=secret right=37.48.75.97 rightid="" auto=add Log file of VPN connection build up: aug. 23 17:12:54.708 ipsec_setup: Starting Openswan IPsec U2.6.38/K3.11.0-12-generic... aug. 23 17:12:55.155 ipsec_setup: multiple ip addresses, using 192.168.178.32 on eth0 aug. 23 17:12:55.165 ipsec__plutorun: Starting Pluto subsystem... aug. 23 17:12:55.174 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d aug. 23 17:12:55.177 recvref[30]: Protocol not available aug. 23 17:12:55.177 xl2tpd[14339]: This binary does not support kernel L2TP. aug. 23 17:12:55.178 Starting xl2tpd: xl2tpd. aug. 23 17:12:55.178 xl2tpd[14345]: xl2tpd version xl2tpd-1.3.1 started on desktopmint PID:14345 aug. 23 17:12:55.178 xl2tpd[14345]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. aug. 23 17:12:55.179 xl2tpd[14345]: Forked by Scott Balmos and David Stipp, (C) 2001 aug. 23 17:12:55.179 xl2tpd[14345]: Inherited by Jeff McAdams, (C) 2002 aug. 23 17:12:55.179 xl2tpd[14345]: Forked again by Xelerance (www.xelerance.com) (C) 2006 aug. 23 17:12:55.180 xl2tpd[14345]: Listening on IP address 0.0.0.0, port 1701 aug. 23 17:12:55.214 ipsec__plutorun: 002 added connection description "Tunnel1" aug. 23 17:13:15.532 104 "Tunnel1" #1: STATE_MAIN_I1: initiate aug. 23 17:13:15.532 003 "Tunnel1" #1: ignoring unknown Vendor ID payload [4f45755c645c6a795c5c6170] aug. 23 17:13:15.532 003 "Tunnel1" #1: received Vendor ID payload [Dead Peer Detection] aug. 23 17:13:15.533 003 "Tunnel1" #1: received Vendor ID payload [RFC 3947] method set to=115 aug. 23 17:13:15.533 106 "Tunnel1" #1: STATE_MAIN_I2: sent MI2, expecting MR2 aug. 23 17:13:15.534 003 "Tunnel1" #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): i am NATed aug. 23 17:13:15.534 108 "Tunnel1" #1: STATE_MAIN_I3: sent MI3, expecting MR3 aug. 23 17:13:15.534 010 "Tunnel1" #1: STATE_MAIN_I3: retransmission; will wait 20s for response aug. 23 17:13:15.545 003 "Tunnel1" #1: received Vendor ID payload [CAN-IKEv2] aug. 23 17:13:15.547 004 "Tunnel1" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp2048} aug. 23 17:13:15.547 117 "Tunnel1" #2: STATE_QUICK_I1: initiate aug. 23 17:13:15.547 010 "Tunnel1" #2: STATE_QUICK_I1: retransmission; will wait 20s for response aug. 23 17:13:15.548 004 "Tunnel1" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x0ecef28b <0x3e1fbe3b xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} aug. 23 17:13:16.549 xl2tpd[14345]: Connecting to host <VPN gateway>, port 1701 aug. 23 17:13:18.576 xl2tpd[14345]: Connection established to <VPN gateway>, 1701. Local: 21163, Remote: 12074 (ref=0/0). aug. 23 17:13:18.576 xl2tpd[14345]: Calling on tunnel 21163 aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.599 xl2tpd[14345]: Call established with <VPN gateway>, Local: 39035, Remote: 57266, Serial: 1 (ref=0/0) aug. 23 17:13:18.605 xl2tpd[14345]: start_pppd: I'm running: aug. 23 17:13:18.605 xl2tpd[14345]: "/usr/sbin/pppd" aug. 23 17:13:18.606 xl2tpd[14345]: "passive" aug. 23 17:13:18.606 xl2tpd[14345]: "nodetach" aug. 23 17:13:18.606 xl2tpd[14345]: ":" aug. 23 17:13:18.606 xl2tpd[14345]: "file" aug. 23 17:13:18.606 xl2tpd[14345]: "/etc/ppp/Tunnel1.options.xl2tpd" aug. 23 17:13:18.606 xl2tpd[14345]: "ipparam" aug. 23 17:13:18.607 xl2tpd[14345]: "<VPN gateway>" aug. 23 17:13:18.607 xl2tpd[14345]: "/dev/pts/4" aug. 23 17:13:18.607 pppd[14438]: Plugin passprompt.so loaded. aug. 23 17:13:18.607 pppd[14438]: pppd 2.4.5 started by root, uid 0 aug. 23 17:13:18.608 pppd[14438]: Using interface ppp0 aug. 23 17:13:18.608 pppd[14438]: Connect: ppp0 <--> /dev/pts/4 aug. 23 17:13:21.650 pppd[14438]: CHAP authentication succeeded: Access granted aug. 23 17:13:21.651 pppd[14438]: CHAP authentication succeeded aug. 23 17:13:21.692 pppd[14438]: local IP address 10.1.2.2 aug. 23 17:13:21.693 pppd[14438]: remote IP address 10.1.2.1 aug. 23 17:13:21.693 pppd[14438]: primary DNS address 10.1.2.1 aug. 23 17:13:21.694 pppd[14438]: secondary DNS address 10.1.2.1 aug. 23 17:13:46.528 Stopping xl2tpd: xl2tpd. aug. 23 17:13:46.528 xl2tpd[14345]: death_handler: Fatal signal 15 received aug. 23 17:13:46.529 pppd[14438]: Modem hangup aug. 23 17:13:46.529 pppd[14438]: Connect time 0.5 minutes. aug. 23 17:13:46.529 pppd[14438]: Sent 1866 bytes, received 1241 bytes. aug. 23 17:13:46.529 pppd[14438]: Connection terminated. aug. 23 17:13:46.562 ipsec_setup: Stopping Openswan IPsec... aug. 23 17:13:46.576 pppd[14438]: Exit.

  Read the article

• Nagios plugin script not working as expected

  - by Linker3000

  I have modified an off-the-shelf Nagios plugin perl script to (in theory) return a one or zero according to the existence, or not, of a file on a remote linux server. The script runs a remote ssh session and logs in as the nagios user. The remote linux servers have private keys setup for that user, and on the bash command line the script works as expected, but when run as a plugin it always returns '1' (true) even if the file does not exist. Some help with the logic or a comment on why things are not working as expected within Nagios would be appreciated. I'd prefer to use this ssh login method rather than having to install nrpe on all the linux servers. To run from a command line (assuming remote server has a user called nagios with a valid private key): ./check_reboot_required -e ssh -H remote-servers-ip-addr -p 'filename-to-check' -v Ta. #! /usr/bin/perl -w # # # License Information: # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by # the Free Software Foundation; either version 2 of the License, or # (at your option) any later version. # # This program is distributed in the hope that it will be useful, # but WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the # GNU General Public License for more details. # # You should have received a copy of the GNU General Public License # along with this program; if not, write to the Free Software # Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. # ############################################################################ use POSIX; use strict; use Getopt::Long; use lib "/usr/lib/nagios/plugins" ; use vars qw($host $opt_V $opt_h $opt_v $verbose $PROGNAME $pattern $opt_p $mmin $opt_e $opt_t $opt_H $status $state $msg $msg_q $MAILQ $SHELL $device $used $avail $percent $fs $blocks $CMD $RMTOS); use utils qw(%ERRORS &print_revision &support &usage ); sub print_help (); sub print_usage (); sub process_arguments (); $ENV{'PATH'}=''; $ENV{'BASH_ENV'}=''; $ENV{'ENV'}=''; $PROGNAME = "check_reboot_required"; Getopt::Long::Configure('bundling'); $status = process_arguments(); if ($status){ print "ERROR: processing arguments\n"; exit $ERRORS{'UNKNOWN'}; } $SIG{'ALRM'} = sub { print ("ERROR: timed out waiting for $CMD on $host\n"); exit $ERRORS{'WARNING'}; }; $host = $opt_H; $pattern = $opt_p; print "Pattern >" . $pattern . "< " if $verbose; alarm($opt_t); #$CMD = "/usr/bin/find " . $pattern . " -type f 2>/dev/null| /usr/bin/wc -l"; $CMD = "[ -f " . $pattern . " ] && echo 1 || echo 0"; alarm($opt_t); ## get cmd output from remote system if (! open (OUTPUT, "$SHELL $host $CMD|" ) ) { print "ERROR: could not open $CMD on $host\n"; exit $ERRORS{'UNKNOWN'}; } my $perfdata = ""; my $state = "3"; my $msg = "Indeterminate result"; # only first line is relevant in this iteration. while (<OUTPUT>) { my $result = chomp($_); $msg = $result; print "Shell returned >" . $result . "< length is " . length($result) . " " if $verbose; if ( $result == 1 ) { $msg = "Reboot required (NB: Result still not accurate)" . $result ; $state = $ERRORS{'WARNING'}; last; } elsif ( $result == 0 ) { $msg = "No reboot required (NB: Result still not accurate) " . $result ; $state = $ERRORS{'OK'}; last; } else { $msg = "Output received, but it was neither a 1 nor a 0" ; last; } } close (OUTPUT); print "$msg | $perfdata\n"; exit $state; ##################################### #### subs sub process_arguments(){ GetOptions ("V" => \$opt_V, "version" => \$opt_V, "v" => \$opt_v, "verbose" => \$opt_v, "h" => \$opt_h, "help" => \$opt_h, "e=s" => \$opt_e, "shell=s" => \$opt_e, "p=s" => \$opt_p, "pattern=s" => \$opt_p, "t=i" => \$opt_t, "timeout=i" => \$opt_t, "H=s" => \$opt_H, "hostname=s" => \$opt_H ); if ($opt_V) { print_revision($PROGNAME,'$Revision: 1.0 $ '); exit $ERRORS{'OK'}; } if ($opt_h) { print_help(); exit $ERRORS{'OK'}; } if (defined $opt_v ){ $verbose = $opt_v; } if (defined $opt_e ){ if ( $opt_e eq "ssh" ) { if (-x "/usr/local/bin/ssh") { $SHELL = "/usr/local/bin/ssh"; } elsif ( -x "/usr/bin/ssh" ) { $SHELL = "/usr/bin/ssh"; } else { print_usage(); exit $ERRORS{'UNKNOWN'}; } } elsif ( $opt_e eq "rsh" ) { $SHELL = "/usr/bin/rsh"; } else { print_usage(); exit $ERRORS{'UNKNOWN'}; } } else { print_usage(); exit $ERRORS{'UNKNOWN'}; } unless (defined $opt_t) { $opt_t = $utils::TIMEOUT ; # default timeout } unless (defined $opt_H) { print_usage(); exit $ERRORS{'UNKNOWN'}; } return $ERRORS{'OK'}; } sub print_usage () { print "Usage: $PROGNAME -e <shell> -H <hostname> -p <directory/file pattern> [-t <timeout>] [-v verbose]\n"; } sub print_help () { print_revision($PROGNAME,'$Revision: 0.1 $'); print "\n"; print_usage(); print "\n"; print " Checks for the presence of a 'reboot-required' file on a remote host via SSH or RSH\n"; print "-e (--shell) = ssh or rsh (required)\n"; print "-H (--hostname) = remote server name (required)"; print "-p (--pattern) = File pattern for find command (default = /var/run/reboot-required)\n"; print "-t (--timeout) = Plugin timeout in seconds (default = $utils::TIMEOUT)\n"; print "-h (--help)\n"; print "-V (--version)\n"; print "-v (--verbose) = debugging output\n"; print "\n\n"; support(); }

  Read the article

• Why are some programs writing on stderr instead of stdout their output?

  - by Zagorax

  I've recently added to my .bashrc file an ssh-add command. I found that ssh-add $HOME/.ssh/id_rsa_github > /dev/null results on a message "identity added and something else" every time I open a shell. While ssh-add $HOME/.ssh/id_rsa_github > /dev/null 2>&1 did the trick and my shell is now 'clean'. Reading on internet, I found that other command do it, (for example time). Could you please explain why it's done?

  Read the article

• iptables syn flood countermeasure

  - by Penegal

  I'm trying to adjust my iptables firewall to increase the security of my server, and I found something a bit problematic here : I have to set INPUT policy to ACCEPT and, in addition, to have a rule saying iptables -I INPUT -i eth0 -j ACCEPT. Here comes my script (launched manually for tests) : #!/bin/sh IPT=/sbin/iptables echo "Clearing firewall rules" $IPT -F $IPT -Z $IPT -t nat -F $IPT -t nat -Z $IPT -t mangle -F $IPT -t mangle -Z $IPT -X echo "Defining logging policy for dropped packets" $IPT -N LOGDROP $IPT -A LOGDROP -j LOG -m limit --limit 5/min --log-level debug --log-prefix "iptables rejected: " $IPT -A LOGDROP -j DROP echo "Setting firewall policy" $IPT -P INPUT DROP # Deny all incoming connections $IPT -P OUTPUT ACCEPT # Allow all outgoing connections $IPT -P FORWARD DROP # Deny all forwaring echo "Allowing connections from/to lo and incoming connections from eth0" $IPT -I INPUT -i lo -j ACCEPT $IPT -I OUTPUT -o lo -j ACCEPT #$IPT -I INPUT -i eth0 -j ACCEPT echo "Setting SYN flood countermeasures" $IPT -A INPUT -p tcp -i eth0 --syn -m limit --limit 100/second --limit-burst 200 -j LOGDROP echo "Allowing outgoing traffic corresponding to already initiated connections" $IPT -A OUTPUT -p ALL -m state --state ESTABLISHED,RELATED -j ACCEPT echo "Allowing incoming SSH" $IPT -A INPUT -p tcp --dport 22 -m state --state NEW -m recent --set --name SSH -j ACCEPT echo "Setting SSH bruteforce attacks countermeasures (deny more than 10 connections every 10 minutes)" $IPT -A INPUT -p tcp --dport 22 -m recent --update --seconds 600 --hitcount 10 --rttl --name SSH -j LOGDROP echo "Allowing incoming traffic for HTTP, SMTP, NTP, PgSQL and SolR" $IPT -A INPUT -p tcp --dport 25 -i eth0 -j ACCEPT $IPT -A INPUT -p tcp --dport 80 -i eth0 -j ACCEPT $IPT -A INPUT -p udp --dport 123 -i eth0 -j ACCEPT $IPT -A INPUT -p tcp --dport 5433 -i eth0.2654 -s 172.16.0.2 -j ACCEPT $IPT -A INPUT -p udp --dport 5433 -i eth0.2654 -s 172.16.0.2 -j ACCEPT $IPT -A INPUT -p tcp --dport 8983 -i eth0.2654 -s 172.16.0.2 -j ACCEPT $IPT -A INPUT -p udp --dport 8983 -i eth0.2654 -s 172.16.0.2 -j ACCEPT echo "Allowing outgoing traffic for ICMP, SSH, whois, SMTP, DNS, HTTP, PgSQL and SolR" $IPT -A OUTPUT -p tcp --dport 22 -j ACCEPT $IPT -A OUTPUT -p tcp --dport 25 -o eth0 -j ACCEPT $IPT -A OUTPUT -p tcp --dport 43 -o eth0 -j ACCEPT $IPT -A OUTPUT -p tcp --dport 53 -o eth0 -j ACCEPT $IPT -A OUTPUT -p udp --dport 53 -o eth0 -j ACCEPT $IPT -A OUTPUT -p tcp --dport 80 -o eth0 -j ACCEPT $IPT -A OUTPUT -p udp --dport 80 -o eth0 -j ACCEPT #$IPT -A OUTPUT -p tcp --dport 5433 -o eth0 -d 176.31.236.101 -j ACCEPT #$IPT -A OUTPUT -p udp --dport 5433 -o eth0 -d 176.31.236.101 -j ACCEPT #$IPT -A OUTPUT -p tcp --dport 8983 -o eth0 -d 176.31.236.101 -j ACCEPT #$IPT -A OUTPUT -p udp --dport 8983 -o eth0 -d 176.31.236.101 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 5433 -o eth0.2654 -j ACCEPT $IPT -A OUTPUT -p udp --sport 5433 -o eth0.2654 -j ACCEPT $IPT -A OUTPUT -p tcp --sport 8983 -o eth0.2654 -j ACCEPT $IPT -A OUTPUT -p udp --sport 8983 -o eth0.2654 -j ACCEPT $IPT -A OUTPUT -p icmp -j ACCEPT echo "Allowing outgoing FTP backup" $IPT -A OUTPUT -p tcp --dport 20:21 -o eth0 -d 91.121.190.78 -j ACCEPT echo "Dropping and logging everything else" $IPT -A INPUT -s 0/0 -j LOGDROP $IPT -A OUTPUT -j LOGDROP $IPT -A FORWARD -j LOGDROP echo "Firewall loaded." echo "Maintaining new rules for 3 minutes for tests" sleep 180 $IPT -nvL echo "Clearing firewall rules" $IPT -F $IPT -Z $IPT -t nat -F $IPT -t nat -Z $IPT -t mangle -F $IPT -t mangle -Z $IPT -X $IPT -P INPUT ACCEPT $IPT -P OUTPUT ACCEPT $IPT -P FORWARD ACCEPT When I launch this script (I only have a SSH access), the shell displays every message up to Maintaining new rules for 3 minutes for tests, the server is unresponsive during the 3 minutes delay and then resume normal operations. The only solution I found until now was to set $IPT -P INPUT ACCEPT and $IPT -I INPUT -i eth0 -j ACCEPT, but this configuration does not protect me of any attack, which is a great shame for a firewall. I suspect that the error comes from my script and not from iptables, but I don't understand what's wrong with my script. Could some do-gooder explain me my error, please? EDIT: here comes the result of iptables -nvL with the "accept all input" ($IPT -P INPUT ACCEPT and $IPT -I INPUT -i eth0 -j ACCEPT) solution : Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 1 52 ACCEPT all -- eth0 * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 LOGDROP tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 100/sec burst 200 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 state NEW recent: SET name: SSH side: source 0 0 LOGDROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 recent: UPDATE seconds: 600 hit_count: 10 TTL-Match name: SSH side: source 0 0 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 0 0 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 0 0 ACCEPT udp -- eth0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:123 0 0 ACCEPT tcp -- eth0.2654 * 172.16.0.2 0.0.0.0/0 tcp dpt:5433 0 0 ACCEPT udp -- eth0.2654 * 172.16.0.2 0.0.0.0/0 udp dpt:5433 0 0 ACCEPT tcp -- eth0.2654 * 172.16.0.2 0.0.0.0/0 tcp dpt:8983 0 0 ACCEPT udp -- eth0.2654 * 172.16.0.2 0.0.0.0/0 udp dpt:8983 0 0 LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 2 728 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:43 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 0 0 ACCEPT udp -- * eth0 0.0.0.0/0 0.0.0.0/0 udp dpt:53 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 0 0 ACCEPT udp -- * eth0 0.0.0.0/0 0.0.0.0/0 udp dpt:80 0 0 ACCEPT tcp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 tcp spt:5433 0 0 ACCEPT udp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 udp spt:5433 0 0 ACCEPT tcp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 tcp spt:8983 0 0 ACCEPT udp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 udp spt:8983 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 91.121.190.78 tcp dpts:20:21 0 0 LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain LOGDROP (5 references) pkts bytes target prot opt in out source destination 0 0 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 5/min burst 5 LOG flags 0 level 7 prefix `iptables rejected: ' 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 EDIT #2 : I modified my script (policy ACCEPT, defining authorized incoming packets then logging and dropping everything else) to write iptables -nvL results to a file and to allow only 10 ICMP requests per second, logging and dropping everything else. The result proved unexpected : while the server was unavailable to SSH connections, even already established, I ping-flooded it from another server, and the ping rate was restricted to 10 requests per second. During this test, I also tried to open new SSH connections, which remained unanswered until the script flushed rules. Here comes the iptables stats written after these tests : Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 600 35520 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 6 360 LOGDROP tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 100/sec burst 200 0 0 LOGDROP tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 STRING match "w00tw00t.at.ISC.SANS." ALGO name bm TO 65535 0 0 LOGDROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 STRING match "Host: anoticiapb.com.br" ALGO name bm TO 65535 0 0 LOGDROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 STRING match "Host: www.anoticiapb.com.br" ALGO name bm TO 65535 105 8820 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 10/sec burst 5 830 69720 LOGDROP icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 state NEW recent: SET name: SSH side: source 0 0 LOGDROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 recent: UPDATE seconds: 600 hit_count: 10 TTL-Match name: SSH side: source 0 0 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 0 0 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 0 0 ACCEPT udp -- eth0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:80 0 0 ACCEPT udp -- eth0 * 0.0.0.0/0 0.0.0.0/0 udp dpt:123 0 0 ACCEPT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:443 0 0 ACCEPT tcp -- eth0.2654 * 172.16.0.1 0.0.0.0/0 tcp spt:5433 0 0 ACCEPT udp -- eth0.2654 * 172.16.0.1 0.0.0.0/0 udp spt:5433 0 0 ACCEPT tcp -- eth0.2654 * 172.16.0.1 0.0.0.0/0 tcp spt:8983 0 0 ACCEPT udp -- eth0.2654 * 172.16.0.1 0.0.0.0/0 udp spt:8983 16 1684 LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 600 35520 ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 0 0 LOGDROP tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 owner UID match 33 0 0 LOGDROP udp -- * eth0 0.0.0.0/0 0.0.0.0/0 udp dpt:80 owner UID match 33 116 11136 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 0 0 ACCEPT udp -- * eth0 0.0.0.0/0 0.0.0.0/0 udp dpt:53 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 0 0 ACCEPT udp -- * eth0 0.0.0.0/0 0.0.0.0/0 udp dpt:80 0 0 ACCEPT tcp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 tcp dpt:5433 0 0 ACCEPT udp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 udp dpt:5433 0 0 ACCEPT tcp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 tcp dpt:8983 0 0 ACCEPT udp -- * eth0.2654 0.0.0.0/0 0.0.0.0/0 udp dpt:8983 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 0.0.0.0/0 tcp dpt:43 0 0 ACCEPT tcp -- * eth0 0.0.0.0/0 91.121.190.18 tcp dpts:20:21 7 1249 LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain LOGDROP (11 references) pkts bytes target prot opt in out source destination 35 3156 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 1/sec burst 5 LOG flags 0 level 7 prefix `iptables rejected: ' 859 73013 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 Here comes the log content added during this test : Mar 28 09:52:51 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=52 TOS=0x00 PREC=0x00 TTL=51 ID=55666 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:51 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=52 TOS=0x00 PREC=0x00 TTL=51 ID=55667 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:51 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=64 TOS=0x00 PREC=0x00 TTL=51 ID=55668 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:51 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=64 TOS=0x00 PREC=0x00 TTL=51 ID=55669 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:52 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=64 TOS=0x00 PREC=0x00 TTL=51 ID=55670 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:54 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=64 TOS=0x00 PREC=0x00 TTL=51 ID=55671 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:58 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=64 TOS=0x00 PREC=0x00 TTL=51 ID=55672 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:52:59 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=6 Mar 28 09:52:59 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=7 Mar 28 09:52:59 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=8 Mar 28 09:52:59 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=9 Mar 28 09:52:59 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=59 Mar 28 09:53:00 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=152 Mar 28 09:53:01 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=246 Mar 28 09:53:02 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=339 Mar 28 09:53:03 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=432 Mar 28 09:53:04 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=524 Mar 28 09:53:05 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=617 Mar 28 09:53:06 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=711 Mar 28 09:53:07 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=804 Mar 28 09:53:08 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=176.31.236.101 DST=176.31.238.3 LEN=84 TOS=0x00 PREC=0x00 TTL=63 ID=0 DF PROTO=ICMP TYPE=8 CODE=0 ID=7430 SEQ=897 Mar 28 09:53:16 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:c0:62:6b:e3:5c:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=61402 DF PROTO=TCP SPT=57637 DPT=22 WINDOW=5840 RES=0x00 SYN URGP=0 Mar 28 09:53:19 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:c0:62:6b:e3:5c:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=61403 DF PROTO=TCP SPT=57637 DPT=22 WINDOW=5840 RES=0x00 SYN URGP=0 Mar 28 09:53:21 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=64 TOS=0x00 PREC=0x00 TTL=51 ID=55674 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK URGP=0 Mar 28 09:53:25 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:c0:62:6b:e3:5c:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=61404 DF PROTO=TCP SPT=57637 DPT=22 WINDOW=5840 RES=0x00 SYN URGP=0 Mar 28 09:53:37 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=116 TOS=0x00 PREC=0x00 TTL=51 ID=55675 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:37 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=116 TOS=0x00 PREC=0x00 TTL=51 ID=55676 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:37 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=180 TOS=0x00 PREC=0x00 TTL=51 ID=55677 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:38 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=180 TOS=0x00 PREC=0x00 TTL=51 ID=55678 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:39 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=180 TOS=0x00 PREC=0x00 TTL=51 ID=55679 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:39 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:c0:62:6b:e3:5c:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=5055 DF PROTO=TCP SPT=57638 DPT=22 WINDOW=5840 RES=0x00 SYN URGP=0 Mar 28 09:53:41 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=180 TOS=0x00 PREC=0x00 TTL=51 ID=55680 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:42 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:c0:62:6b:e3:5c:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=5056 DF PROTO=TCP SPT=57638 DPT=22 WINDOW=5840 RES=0x00 SYN URGP=0 Mar 28 09:53:45 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:10:8c:cf:28:39:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=180 TOS=0x00 PREC=0x00 TTL=51 ID=55681 DF PROTO=TCP SPT=57504 DPT=22 WINDOW=501 RES=0x00 ACK PSH URGP=0 Mar 28 09:53:48 localhost kernel: iptables rejected: IN=eth0 OUT= MAC=00:25:90:54:d7:88:c0:62:6b:e3:5c:80:08:00 SRC=194.51.74.245 DST=176.31.238.3 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=5057 DF PROTO=TCP SPT=57638 DPT=22 WINDOW=5840 RES=0x00 SYN URGP=0 If I correctly interpreted these results, they say that ICMP rules were correctly interpreted by iptables, but SSH rules were not. This does not make any sense... Does somebody understand where my error comes from? EDIT #3 : After some more tests, I found out that commenting the SYN flood countermeasure removes the problem. I continue researches in this way but, meanwhile, if somebody sees my anti SYN flood rule error...

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >