Search Results

Search found 12431 results on 498 pages for 'errors'.

Page 89/498 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

  • Connection reset by peer: mod_fcgid: error reading data from FastCGI server Issues

    - by user145857
    Help is greatly needed for our server. We are experiencing random "Connection reset by peer: mod_fcgid: error reading data from FastCGI server" errors which cause a 500 internal server error. If the page is then reloaded it loads normally as it should. We are running MPM Worker with mod FCGID to handle PHP. We had APC cache enabled but disabled it recently to see if it would fix the problem, but the random mod FCGID errors are still continuing. No other opcode cache is active now. Our settings are below: <IfModule worker.c> MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 ThreadLimit 100 ServerLimit 700 MaxClients 700 MaxRequestsPerChild 0 </IfModule> <IfModule mod_fcgid.c> FcgidMaxRequestLen 1073741824 FcgidMaxRequestsPerProcess 2000 FcgidMaxProcessesPerClass 100 FcgidMinProcessesPerClass 0 FcgidConnectTimeout 300 FcgidIOTimeout 900 FcgidFixPathinfo 1 FcgidIdleTimeout 300 FcgidIdleScanInterval 120 FcgidBusyTimeout 300 FcgidBusyScanInterval 120 FcgidErrorScanInterval 12 FcgidZombieScanInterval 12 FcgidProcessLifeTime 3600 </IfModule> The server is a 64 core 2.1 GHZ 94 GB RAM so it has some power. Some of the fcgid timeout settings are higher because we run large reports which take up to 15 minutes. Any help is greatly appreciated! Just to clarify, the random fcgid errors are occurring when a user clicks a page on our site and the 500 error page loads instantly. This is random and occurrs less than 1% of the time but it is still an issue.

    Read the article

  • Centos 6.2 Fresh 'Basic Server' install networking issues

    - by RWC
    I've had a /29 provisioned on a network port for a server and am trying to at least configure the machine so I can ssh into it. It's Centos 6.2 x64 with the Basic Server install. Currently not able to ping gateway or any address for that matter. For reference: Default Interface: em2 Network ID: 66.*.*.0/29 Gateway: 66.*.*.1 Broadcast: 66.*.*.7 Please see my following configs: /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 NM_CONTROLLED=yes ONBOOT=yes HWADDR=Not Important TYPE=Ethernet BOOTPROTO=none IPADDR=66.*.*.2 PREFIX=29 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System em2" NETMASK=255.255.255.248 USERCTL=no $: route -n Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 0.0.0.0 255.255.255.248 U 0 0 0 em2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 1003 0 em2 0.0.0.0 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: route Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 * 255.255.255.248 U 0 0 0 em2 link-local * 255.255.0.0 U 0 1003 0 em2 default 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=excalibur.domain.com GATEWAY=66.*.*.1 Keep in mind that I cannot even currently ping the gateway which is quite confusing for me. My /etc/hosts are configured correctly with the *.2 address. I'm not concerned with getting all of the addresses on the /29 up and running yet, just one so I can at least ssh in. Thanks! Edit: Adding in ifconfig. $: ifconfig em2 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX inet addr:66.*.*.2 Bcat:66.*.*.7 Mask:255.255.255.248 inet6 addr: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5536 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2599469 (2.4 MiB) TX bytes: 748 (748.0 b) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 etc etc

    Read the article

  • NFS high CPU usage

    - by user269836
    Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

    Read the article

  • Unable to logon using terminal server connection

    - by satch
    I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • SQL Server 2008 Cluster Installation - First network name always fails

    - by boflynn
    I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

    Read the article

  • BSOD: PFN_LIST_CORRUPT and IRQ_NOT_LESS_OR_EQUAL

    - by David Lively
    I built a desktop about a year ago that has, until a few weeks ago, been running without a hitch using Windows 7 Ultimate. Recently, the PC started occasionally rebooting with a blue screen indicating a "PFN_LIST_CORRUPT" error. Also, I've seen at least once the error IRQ_NOT_LESS_OR_EQUAL. I seem to remember temporarily connecting an internal DVD burner about the same time this happened. I burned a DVD for another machine and promptly removed the drive. Yesterday, I reformatted the drive and installed Win7 Ultimate x64. During the first install, the PFN_LIST_CORRUPT bluescreen reared its ugly head again. A second install attempt completed with no errors. The fact that this error happened during a clean install leads me to believe that this is not a driver or OS issue. I also ran the memory diagnostic from the Win7 32-bit install DVD. It completed both passes with no errors. Periodically, the screen will flicker, as if explorer or the video are resetting. In the event log, I see a series of 8 or so errors indicating that some services unexpectedly stopped, and were apparently reset. These include an HID service and some others (I don't have a list in front of me). The PC is a Phenom X2 3 Ghz with a 500GB Seagate drive, 4GB of Corsair XMS2 cm2x2048-6400c5c. Anyone know what would suddenly cause a couple of sticks of RAM to go bad?

    Read the article

  • Trouble cloning a Macbook Pro hard drive

    - by Mirko Froehlich
    I am trying to upgrade the 250GB hard drive in my MacBook Pro (early 2008 model) to a 750GB drive. I have connected the new drive via an external USB enclosure. The drive is recognized fine, I can format it, etc. However, every time I try to clone the drive, I am getting Input/Output errors. Before the clone operation, I have verified both the internal and the external drive using Disk Utility, and they both check out fine. After the clone operation, the external drive shows multiple "Invalid node structure" errors: I have tried two approaches for cloning the drive: Using Disk Utility, by starting from the OSX install DVD Using Carbon Copy Cloner The outcome is the same in both cases. The Carbon Copy Cloner logs show a handful of the following types of errors: rsync: mkstemp "<... an external filename ...>" failed: Input/output error (5) rsync: stat "<... an external filename ...>" failed: Input/output error (5) The actual files affected seem to be different across different runs of the application. Before the last run, I used Disk Utility to (once more) reformat the external drive and explicitly overwrite it with zeros, but this made no difference. I also tried running a surface scan in Tech Tool Pro overnight. It got about 2/3 of the way through before I had to disconnect the drive (had to take my MacBook Pro to work), but so far it didn't report any bad blocks. Assuming it scans the drive in the same order in which blocks would be allocated during actual use, it seems like if bad blocks were to blame for the clone failures, they should have been found already (given that the source drive is only 250GB). As a last attempt, I may try SuperDuper as well, although my understanding is that it uses the same underlying rsync approach as Carbon Copy Cloner, so it's unlikely to perform any better. Are there any other things I should try before I send the drive in for a replacement? Could these problems be caused by my internal drive, even though it works fine and checks out fine in Disk Utility?

    Read the article

  • install zenoss on ubuntu, raise No valid ZENHOME error

    - by bxshi
    I've added an user with name zenoss, and set export ZENHOME=/usr/local/zenoss in ~/.bashrc under /home/zenoss, and when using echo $ZENHOME, it could show /usr/local/zenoss When install zenoss, I switched to zenoss and then run install.sh under zenoss-4.2.0/inst, when it tries to run Tests, the error occured. ------------------------------------------------------- T E S T S ------------------------------------------------------- Running org.zenoss.utils.ZenPacksTest Tests run: 3, Failures: 0, Errors: 3, Skipped: 0, Time elapsed: 0.045 sec <<< FAILURE! Running org.zenoss.utils.ZenossTest Tests run: 3, Failures: 0, Errors: 0, Skipped: 0, Time elapsed: 0.71 sec Results : Tests in error: testGetZenPack(org.zenoss.utils.ZenPacksTest): No valid ZENHOME could be found. testGetPackPath(org.zenoss.utils.ZenPacksTest): No valid ZENHOME could be found. testGetAllPacks(org.zenoss.utils.ZenPacksTest): No valid ZENHOME could be found. Tests run: 6, Failures: 0, Errors: 3, Skipped: 0 [INFO] ------------------------------------------------------------------------ [INFO] Reactor Summary: [INFO] [INFO] Zenoss Core ....................................... SUCCESS [27.643s] [INFO] Zenoss Core Utilities ............................. FAILURE [12.742s] [INFO] Zenoss Jython Distribution ........................ SKIPPED [INFO] ------------------------------------------------------------------------ [INFO] BUILD FAILURE [INFO] ------------------------------------------------------------------------ [INFO] Total time: 40.586s [INFO] Finished at: Wed Sep 26 15:39:24 CST 2012 [INFO] Final Memory: 16M/60M [INFO] ------------------------------------------------------------------------ [ERROR] Failed to execute goal org.apache.maven.plugins:maven-surefire-plugin:2.8:test (default-test) on project utils: There are test failures. [ERROR] [ERROR] Please refer to /home/zenoss/zenoss-4.2.0/inst/build/java/java/zenoss-utils/target/surefire-reports for the individual test results.

    Read the article

  • mount error 5 = Input/output error

    - by alharaka
    I am running out of ideas. After a long period of testing this morning, I cannot seem to get this to work, and I have no idea why. I want to mount a Windows SMB/CIFS share with a Debian 5.0.4 VM, and it is not cooperating. This the command I am using. debianvm:/home/me# whoami root debianvm:/home/me# smbclient --version Version 3.2.5 debianvm:/home/me# mount -t cifs //hostname.domain.tld/share /mnt/hostname.domain.tld/share --verbose -o user=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD/username mount.cifs kernel mount options: unc=//hostname.domain.tld\share,ip=10.212.15.53,domain=SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD,ver=1,rw,user=username,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,pass=*********mount error 5 = Input/output error Refer to the mount.cifs(8) manual page (e.g.man mount.cifs) debianvm:/home/me# The word on the nets has not been very specific, and unfortunately it is almost always environment-specific. I receive no authentication errors. I have tried mount -t smbfs and mount -t cifs, along with smbmount and such. I get the same error before. I doubt it is a problem with DNS resolution, because logging shows the correct IP address. dmesg | tail -f no longer shows authentication errors when I format the domain and username accordingly. I have played a little with iocharset=utf8, file_mode, and dir_mode as described here. That did not help either. I have also tried ntlm and ntlmv2 assuming it might be a minimum auth method problem, but not forcing sec=ntlmv2 it can still authenticate without errors anymore. smbclient -L hostname.domain.tld -W SUBADDOMAIN.ADDOMAIN.DOMAIN.TLD -U username correctly lists all the shares and shows it as the following. Domain=[SUBADDOMAIN] OS=[Windows 5.0] Server=[Windows 2000 LAN Manager] Sharename Type Comment --------- ---- ------- IPC$ IPC Remote IPC ETC$ Disk Remote Administration C$ Disk Remote Administration Share Disk Connection to hostname.domain.tld failed (Error NT_STATUS_CONNECTION_REFUSED) NetBIOS over TCP disabled -- no workgroup available I find the last line intriguing/alarming. Does anyone have any pointers!? Maybe I misread the effin manual.

    Read the article

  • Unable to logon using terminal server connection

    - by satch
    I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

    Read the article

  • Linux server: Dropped packets

    - by Lars
    I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

    Read the article

  • Export-Mailbox - fails with large folders

    - by grojo
    I am trying to move messages from a rather large mailbox to an archive mailbox. However I run into errors all the time. the command I am executing is Export-Mailbox -Identity MAILBOX_FROM -TargetMailbox ARCHIVE -TargetFolder ARCHIVE_FOLDER -StartDate 2009-02-01 -EndDate 2009-02-28 -DeleteContent -Confirm:$false I can copy/move some messages, but run into frequent "an unknown error has occurred" (statuscode -1056749164) I run the console as administrative user, and all permissions are set right, as far as I can tell. I've restricted the start and end dates in case the number of messages moved/deleted should create problems. Anything I am missing in my setup? Corrupted messages? Over-limit message sizes? Update: What I've learnt so far, is that folder with more than approx 3000 messages will generate errors. If mail retention is set (default 30 days), Export-Mailbox will scan all messages whether these were deleted in previous runs or not, and date restriction to limit number of messages will not work. To avoid errors, I've switched off deleted message retention for the mailbox, and moved the messages from one large folder to multiple folders, and moved these one by one...

    Read the article

  • Problem with ubuntu 10.10 running from USB drive

    - by Surjya Narayana Padhi
    I recently downloaded Ubuntu 10.10 and created an USB drive with that. I started to run the Ubuntu from that USB drive. But I am facing so much problem. I am thinking why its not so much easy like Windows to do all my job in ubuntu. Always I get some error message or to install something. This time I am getting the following errors. I am trying to download and install Aircrack-ng. So used the command sudo apt-get install aircrack-ng. But the installation stops with the following error : update-initramfs: deferring update (trigger activated) cp: cannot stat `/vmlinuz': No such file or directory dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: initramfs-tools bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1) I don't even have the aptitude command installed till now. Are all these errors because of I am running the ubuntu from USB drive? Is there any simple and easy way to go to Ubuntu Software Center and download all the required essentials at one shot and then Aircrack-ng? I could not find the Aircrack-ng in Ubuntu Software Center Can anybody give me detail steps to solve all my problems above. I am frustrated searching for updates and installations. When something works and something does not work. Can anybody suggest me how I should proceed after installing ubuntu to run on a USB drive. So that I can use the OS like Windows. Like software download,wireless driver, sound, video, documents, C:, D: all things should be there. Please somebody help.

    Read the article

  • Error on LDAP Login - xsessions error - Session lasted less than 10 seconds

    - by Draineh
    I have two machines both running CentOS 5.6 64bit. On the LDAP Machine it has a DHCP, BIND and OpenLDAP Server. LDAP is correctly configured and users can authenticate against it. Using root I configure machine 2 to use LDAP for authentication and when trying to log in it successfully authenticates against a saved user on the LDAP Server but produces the following errors and then throws me back to the login screen. I can still sign in as root and use the machine as normal. The syslog doesn't show any errors and I disabled SELinux to see if it was interfering. The error; Your session only lasted less than 10 seconds. If you have not lgoged out yourself, this could mean that there is some installation problem or that you may be out of diskspace. Try logging in with one of the failsafe sessions to see if you can fix this problem. There is then a tickbox to view the contents of ~/.xsessions-errors which contains; /etc/gdm/PreSession/Default: Registering your session with utmp /etc/gdm/PreSession/Default: running: /usr/bin/sessreg -a -u /var/run/utmp -x "/var/gdm:0:Xservers" -h "" -l ":0" "admin" localuser:admin being added to access control list No profile for user 'admin' found /bin/sh: /usr/bin/dbus-launch --exit-with-session /etc/X11/Xinit/Xclients: No such file or directory /bin/sh: line 0: exec: /usr/bin/dbus-launch --exit-with-session /etc/X11/xinit/Xclients: cannot execute: No such file or directory Apologies if someone notices something isn't spelt quite right or doesn't sound right, the system never actually creates or saves this file so I have had to type it across from the screen. Through the authentication panel in CentOS on the client I have set it to create the users home directory on login. The user is being correctly authenticated and the /home/admin folder has been created but this error would suggest it has not? The client is a new install on an 80gb hard drive so there is well over 80% of the drive still available. Thanks for any suggestions or pointers.

    Read the article

  • Problem with ubuntu 10.10 running from USB drive

    - by Surjya Narayana Padhi
    Hi Geeks, I recently downloaded Ubuntu 10.10 and created an USB drive with that. I started to run the Ubuntu from that USB drive. But I am facing so much problem. I am thinking why its not so much easy like Windows to do all my job in ubuntu. Always I get some error message or to install something. This time I am getting the following errors. I am trying to download and install Aircrack-ng. So used the command sudo apt-get install aircrack-ng. But the installation stops with the following error : update-initramfs: deferring update (trigger activated) cp: cannot stat `/vmlinuz': No such file or directory dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: initramfs-tools bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1) I don't even have the aptitude command installed till now. Are all these errors because of I am running the ubuntu from USB drive? Is there any simple and easy way to go to Ubuntu Software Center and download all the required essentials at one shot and then Aircrack-ng? I could not find the Aircrack-ng in Ubuntu Software Center Can anybody give me detail steps to solve all my problems above. I am frustrated searching for updates and installations. When something works and something does not work. Can anybody suggest me how I should proceed after installing ubuntu to run on a USB drive. So that I can use the OS like Windows. Like software download,wireless driver, sound, video, documents, C:, D: all things should be there. Please somebody help.

    Read the article

  • Need help toubleshooting PC

    - by brux
    I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after restarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What I have done: I thought it was HDD at first, since this is the only part of the computer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from boo-table USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD appears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoroughly. The problem still persists, what should my next steps be?

    Read the article

  • Need help ttoubleshooting PC

    - by brux
    I have had problems since my dog pee'd on my computer. Problem: loads windows fine, at random intervals from 5 minutes to 30 minutes it restarts itself. There is nothing in the event log such as errors, no BSOD, just cold restart. after rstarting - sometimes- it POST's and restarts itself at the end of POST. It will do this many times and then finally load windows. The cycle then begins again, it will restart eventually. What i have done: I thought it was HDD at first, since this is the only part of the coputer which actually got wet with any fluid ( the case is off the PC and the dog pee'd down the front where the HDD is located). Seatool, the seagate HDD tool, found errors when I ran it inside windows, so I ran it in DOS mode from bootable USB and ran it. It found the same number of errors and fixed them all. I ran the scan again and it says "Good". I loaded windows and ran the scan and it also said "Good there. So the HDD apears to be fine but the problem persists, random restarts. What else could this be? I have taken the computer apart and cleaned everything and also taken the PSU apart and cleaned it thoughrouly. The problem still persists, what should my next steps be? Thanks in advance.

    Read the article

  • What may be wrong with String::ToIdentifier::EN tests?

    - by wk01
    I try to install Perl module String::ToIdentifier::EN (as depndency of DBIx::Class::Schema::Loader) but it fails on tests. I googled those errors but get no picture, where is problem: Building and testing String-ToIdentifier-EN-0.07 cp lib/String/ToIdentifier/EN.pm blib/lib/String/ToIdentifier/EN.pm cp lib/String/ToIdentifier/EN/Unicode.pm blib/lib/String/ToIdentifier/EN/Unicode.pm Manifying blib/man3/String::ToIdentifier::EN.3pm Manifying blib/man3/String::ToIdentifier::EN::Unicode.3pm PERL_DL_NONLAZY=1 /usr/bin/perl "-MExtUtils::Command::MM" "-e" "test_harness(0, 'inc', 'blib/lib', 'blib/arch')" t/00_basic.t t/10_ascii.t t/20_capitalization.t Byte order is not compatible at ../../lib/Storable.pm (autosplit into ../../lib/auto/Storable/_retrieve.al) line 380, at /home/wanradt/perl5/lib/perl5/Lingua/EN/Tagger.pm line 167 # Looks like you planned 25 tests but ran 4. # Looks like your test exited with 25 just after 4. t/00_basic.t ........... Dubious, test returned 25 (wstat 6400, 0x1900) Failed 21/25 subtests Byte order is not compatible at ../../lib/Storable.pm (autosplit into ../../lib/auto/Storable/_retrieve.al) line 380, at /home/wanradt/perl5/lib/perl5/Lingua/EN/Tagger.pm line 167 # Looks like you planned 768 tests but ran 512. # Looks like your test exited with 25 just after 512. t/10_ascii.t ........... Dubious, test returned 25 (wstat 6400, 0x1900) Failed 256/768 subtests t/20_capitalization.t .. ok Test Summary Report ------------------- t/00_basic.t (Wstat: 6400 Tests: 4 Failed: 0) Non-zero exit status: 25 Parse errors: Bad plan. You planned 25 tests but ran 4. t/10_ascii.t (Wstat: 6400 Tests: 512 Failed: 0) Non-zero exit status: 25 Parse errors: Bad plan. You planned 768 tests but ran 512. Files=3, Tests=528, 1 wallclock secs ( 0.07 usr 0.02 sys + 0.42 cusr 0.04 csys = 0.55 CPU) Result: FAIL Failed 2/3 test programs. 0/528 subtests failed. make: *** [test_dynamic] Error 255 -> FAIL Installing String::ToIdentifier::EN failed. See /home/wanradt/.cpanm/build.log for details. Byte order is not compatible at... seems a key, but to where?

    Read the article

  • Google Chrome won't install via IE9/Windows7

    - by purir
    Using IE9, I've tried installing Google Chrome on Windows 7 from this url http://www.google.com/chrome/eula.html?hl=en-GB&platform=win But get the following error (apologies for uncouthly dumping this nonsense...) Any ideas dearly appreciated! PLATFORM VERSION INFO Windows : 6.1.7601.65536 (Win32NT) Common Language Runtime : 4.0.30319.235 System.Deployment.dll : 4.0.30319.1 (RTMRel.030319-0100) clr.dll : 4.0.30319.235 (RTMGDR.030319-2300) dfdll.dll : 4.0.30319.1 (RTMRel.030319-0100) dfshim.dll : 4.0.31106.0 (Main.031106-0000) SOURCES Deployment url : _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser ERROR SUMMARY Below is a summary of the errors, details of these errors are listed later in the log. * Activation of _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser resulted in exception. Following failure messages were detected: + The system cannot find the file specified. (Exception from HRESULT: 0x80070002) COMPONENT STORE TRANSACTION FAILURE SUMMARY No transaction error was detected. WARNINGS There were no warnings during this operation. OPERATION PROGRESS STATUS * [25/06/2011 11:41:04] : Activation of _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser has started. ERROR DETAILS Following errors were detected during this operation. * [25/06/2011 11:41:04] System.IO.FileNotFoundException - The system cannot find the file specified. (Exception from HRESULT: 0x80070002) - Source: System.Deployment - Stack trace: at System.Deployment.Internal.Isolation.IsolationInterop.GetUserStore(UInt32 Flags, IntPtr hToken, Guid& riid) at System.Deployment.Application.ComponentStore..ctor(ComponentStoreType storeType, SubscriptionStore subStore) at System.Deployment.Application.SubscriptionStore..ctor(String deployPath, String tempPath, ComponentStoreType storeType) at System.Deployment.Application.SubscriptionStore.get_CurrentUser() at System.Deployment.Application.ApplicationActivator.PerformDeploymentActivation(Uri activationUri, Boolean isShortcut, String textualSubId, String deploymentProviderUrlFromExtension, BrowserSettings browserSettings, String& errorPageUrl) at System.Deployment.Application.ApplicationActivator.ActivateDeploymentWorker(Object state) COMPONENT STORE TRANSACTION DETAILS No transaction information is available.

    Read the article

  • Google Chrome won't install via IE9/Windows7

    - by purir
    Using IE9, I've tried installing Google Chrome on Windows 7 from this url http://www.google.com/chrome/eula.html?hl=en-GB&platform=win But get the following error (apologies for uncouthly dumping this nonsense...) Any ideas dearly appreciated! PLATFORM VERSION INFO Windows : 6.1.7601.65536 (Win32NT) Common Language Runtime : 4.0.30319.235 System.Deployment.dll : 4.0.30319.1 (RTMRel.030319-0100) clr.dll : 4.0.30319.235 (RTMGDR.030319-2300) dfdll.dll : 4.0.30319.1 (RTMRel.030319-0100) dfshim.dll : 4.0.31106.0 (Main.031106-0000) SOURCES Deployment url : _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser ERROR SUMMARY Below is a summary of the errors, details of these errors are listed later in the log. * Activation of _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser resulted in exception. Following failure messages were detected: + The system cannot find the file specified. (Exception from HRESULT: 0x80070002) COMPONENT STORE TRANSACTION FAILURE SUMMARY No transaction error was detected. WARNINGS There were no warnings during this operation. OPERATION PROGRESS STATUS * [25/06/2011 11:41:04] : Activation of _http://dl.google.com/update2/1.3.21.57/GoogleInstaller_en-GB.application?appguid%3D%7B8A69D345-D564-463C-AFF1-A69D9E530F96%7D%26iid%3D%7B26C55C3A-B26A-0484-FEDD-78443D269DA1%7D%26lang%3Den-GB%26browser%3D2%26usagestats%3D0%26appname%3DGoogle%2520Chrome%26needsadmin%3Dfalse%26installdataindex%3Ddefaultbrowser has started. ERROR DETAILS Following errors were detected during this operation. * [25/06/2011 11:41:04] System.IO.FileNotFoundException - The system cannot find the file specified. (Exception from HRESULT: 0x80070002) - Source: System.Deployment - Stack trace: at System.Deployment.Internal.Isolation.IsolationInterop.GetUserStore(UInt32 Flags, IntPtr hToken, Guid& riid) at System.Deployment.Application.ComponentStore..ctor(ComponentStoreType storeType, SubscriptionStore subStore) at System.Deployment.Application.SubscriptionStore..ctor(String deployPath, String tempPath, ComponentStoreType storeType) at System.Deployment.Application.SubscriptionStore.get_CurrentUser() at System.Deployment.Application.ApplicationActivator.PerformDeploymentActivation(Uri activationUri, Boolean isShortcut, String textualSubId, String deploymentProviderUrlFromExtension, BrowserSettings browserSettings, String& errorPageUrl) at System.Deployment.Application.ApplicationActivator.ActivateDeploymentWorker(Object state) COMPONENT STORE TRANSACTION DETAILS No transaction information is available.

    Read the article

  • Windows 7 not booting up and stuck at startup repair

    - by mikimr
    I've been having issues with Windows 7 Home Premium on a Lenovo laptop. At first, it would not start up normally at all. I started it in Safe Mode, where I disabled all non-MS services and tried again to no avail. It then goes into Startup repair where it failed several times. I tried copying the original registry settings, still the same. I resorted to booting with an Ubuntu DVD, where I ran the boot-repair, where it is supposed to correct the Windows boot. No luck. I used Win7 DVD to start up from there, where I had the option to install or repair. I chose the repair, got into command prompt, ran chkdsk /i /r, where it found 3 unreadable segments, went through the 2nd step without issues, and the 3rd step completed with some errors (can't recall the exact errors). When I restarted the machine, it went to straight to the Stratup Repair, indicating "Attempting repairs... Repairing dis errors. This might take over an hour to complete." It's been like this for nearly 15 hours. When I try to cancel or close the Startup Repair window, I get a message "The current repair operation cannot be cancelled." Should I let it run or force shut the machine? If force shut, how can I resolve this problem? Thanks.

    Read the article

  • System Issues and Major Malfuctions after Failed hibernation Exit

    - by Sarah Seguin
    I have a HP G71-340US that went into hibernation mode for a while and when I tried coming out of it, I got an error message: You're computer cannot come out if hibernation . Status: 0xc000009a Info: A fatal error occurred processing the restoration data. File: \hiberfil.sys Any information that was not saved before the computer went into hybernation will be lost enter=continue So I hit continue and it ran soooo super slow it. It was seriously crawling. Finally I gave up and turned it off manually (IE press and hold the button). It's been a week or two since then and EVERY SINGLE TIME I have tried to to do ANYTHING it takes forever. When I say forever, I literally mean takes 5-7 minutes to load the internet, then the page itself, then to click a link, so on so forth. Eventually everything just goes not responding and I have to give up (4-6 HOURS later). I also cannot access my thumb/jump drives once I've managed to load windows. I was going to try runing malware bytes incase of a virus, but it's windows explorer developes errors and goes not responding on me. Currently I'm running scan disk or check disk and like every file is coming back unreadable. I let it run the last 2 hours straight in chkdesk and I'm only at 6 percent with around 500+ errors and still going. Yes, I've taken logs of the errors via cell phone camera and patience. A week or two prior to this happening I had to change our the hard drive due to blunt force trama next to the mouse. OH! Running on Windows 7: ) And I've tried loading the computer in safe mode and it makes absolutely no difference. Any and all help would be appreciated. I really don't know what to do from here and I'm kind of freaking out. I've googled different part of the error and things that I've done/seen and there are so many different answers/topics that I thought it best to just post the questions.

    Read the article

  • Spring validation @AssertTrue

    - by Eqbal
    How do I display on a view jsp validation error message that occurs as a result of @AssertTrue annotation? It isn't tied to a specific field, but I am using it to validate a combination of fields. If I use <form:errors path="*"/> that will display all the errors for that form?

    Read the article

  • How to support both HTTP and HTTPS channels in Flex/BlazeDS?

    - by digitalsanctum
    I've been trying to find the right configuration for supporting both http/s requests in a Flex app. I've read all the docs and they allude to doing something like the following: <default-channels> <channel ref="my-secure-amf"> <serialization> <log-property-errors>true</log-property-errors> </serialization> </channel> <channel ref="my-amf"> <serialization> <log-property-errors>true</log-property-errors> </serialization> </channel> This works great when hitting the app via https but get intermittent communication failures when hitting the same app via http. Here's an abbreviated services-config.xml: <channel-definition id="my-amf" class="mx.messaging.channels.AMFChannel"> <endpoint url="http://{server.name}:{server.port}/{context.root}/messagebroker/amf" class="flex.messaging.endpoints.AMFEndpoint"/> <properties> <!-- HTTPS requests don't work on IE when pragma "no-cache" headers are set so you need to set the add-no-cache-headers property to false --> <add-no-cache-headers>false</add-no-cache-headers> <!-- Use to limit the client channel's connect attempt to the specified time interval. --> <connect-timeout-seconds>10</connect-timeout-seconds> </properties> </channel-definition> <channel-definition id="my-secure-amf" class="mx.messaging.channels.SecureAMFChannel"> <!--<endpoint url="https://{server.name}:{server.port}/{context.root}/messagebroker/amfsecure" class="flex.messaging.endpoints.SecureAMFEndpoint"/>--> <endpoint url="https://{server.name}:{server.port}/{context.root}/messagebroker/amfsecure" class="flex.messaging.endpoints.AMFEndpoint"/> <properties> <add-no-cache-headers>false</add-no-cache-headers> <connect-timeout-seconds>10</connect-timeout-seconds> </properties> </channel-definition> I'm running with Tomcat 5.5.17 and Java 5. The BlazeDS docs say this is the best practice. Is there a better way? With this config, there seems to be 2-3 retries associated with each channel defined in the default-channels element so it always takes ~20s before the my-amf channel connects via a http request. Is there a way to override the 2-3 retries to say, 1 retry for each channel? Thanks in advance for answers.

    Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >