Search Results

Search found 4049 results on 162 pages for 'serial communication'.

Page 89/162 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Are XML Comments Necessary Documentation?

  - by Bob Horn

  I used to be a fan of requiring XML comments for documentation. I've since changed my mind for two main reasons: Like good code, methods should be self-explanatory. In practice, most XML comments are useless noise that provide no additional value. Many times we simply use GhostDoc to generate generic comments, and this is what I mean by useless noise: /// <summary> /// Gets or sets the unit of measure. /// </summary> /// <value> /// The unit of measure. /// </value> public string UnitOfMeasure { get; set; } To me, that's obvious. Having said that, if there were special instructions to include, then we should absolutely use XML comments. I like this excerpt from this article: Sometimes, you will need to write comments. But, it should be the exception not the rule. Comments should only be used when they are expressing something that cannot be expressed in code. If you want to write elegant code, strive to eliminate comments and instead write self-documenting code. Am I wrong to think we should only be using XML comments when the code isn't enough to explain itself on its own? I believe this is a good example where XML comments make pretty code look ugly. It takes a class like this... public class RawMaterialLabel : EntityBase { public long Id { get; set; } public string ManufacturerId { get; set; } public string PartNumber { get; set; } public string Quantity { get; set; } public string UnitOfMeasure { get; set; } public string LotNumber { get; set; } public string SublotNumber { get; set; } public int LabelSerialNumber { get; set; } public string PurchaseOrderNumber { get; set; } public string PurchaseOrderLineNumber { get; set; } public DateTime ManufacturingDate { get; set; } public string LastModifiedUser { get; set; } public DateTime LastModifiedTime { get; set; } public Binary VersionNumber { get; set; } public ICollection<LotEquipmentScan> LotEquipmentScans { get; private set; } } ... And turns it into this: /// <summary> /// Container for properties of a raw material label /// </summary> public class RawMaterialLabel : EntityBase { /// <summary> /// Gets or sets the id. /// </summary> /// <value> /// The id. /// </value> public long Id { get; set; } /// <summary> /// Gets or sets the manufacturer id. /// </summary> /// <value> /// The manufacturer id. /// </value> public string ManufacturerId { get; set; } /// <summary> /// Gets or sets the part number. /// </summary> /// <value> /// The part number. /// </value> public string PartNumber { get; set; } /// <summary> /// Gets or sets the quantity. /// </summary> /// <value> /// The quantity. /// </value> public string Quantity { get; set; } /// <summary> /// Gets or sets the unit of measure. /// </summary> /// <value> /// The unit of measure. /// </value> public string UnitOfMeasure { get; set; } /// <summary> /// Gets or sets the lot number. /// </summary> /// <value> /// The lot number. /// </value> public string LotNumber { get; set; } /// <summary> /// Gets or sets the sublot number. /// </summary> /// <value> /// The sublot number. /// </value> public string SublotNumber { get; set; } /// <summary> /// Gets or sets the label serial number. /// </summary> /// <value> /// The label serial number. /// </value> public int LabelSerialNumber { get; set; } /// <summary> /// Gets or sets the purchase order number. /// </summary> /// <value> /// The purchase order number. /// </value> public string PurchaseOrderNumber { get; set; } /// <summary> /// Gets or sets the purchase order line number. /// </summary> /// <value> /// The purchase order line number. /// </value> public string PurchaseOrderLineNumber { get; set; } /// <summary> /// Gets or sets the manufacturing date. /// </summary> /// <value> /// The manufacturing date. /// </value> public DateTime ManufacturingDate { get; set; } /// <summary> /// Gets or sets the last modified user. /// </summary> /// <value> /// The last modified user. /// </value> public string LastModifiedUser { get; set; } /// <summary> /// Gets or sets the last modified time. /// </summary> /// <value> /// The last modified time. /// </value> public DateTime LastModifiedTime { get; set; } /// <summary> /// Gets or sets the version number. /// </summary> /// <value> /// The version number. /// </value> public Binary VersionNumber { get; set; } /// <summary> /// Gets the lot equipment scans. /// </summary> /// <value> /// The lot equipment scans. /// </value> public ICollection<LotEquipmentScan> LotEquipmentScans { get; private set; } }

  Read the article

• What features are helpful when performing remote debugging / diagnostics?

  - by Pemdas

  Obviously, the easiest way to solve a bug is to be able to reproduce it in-house. However, sometimes that is not practical. For starters, users are often not very good at providing you with useful information. Customer Service: "what seems to be the issue?" User: "It crashed!" To further compound that, sometimes the bug only occurs under certain environmentally conditions that can not be adequately replicated in-house. With that in mind, it is important to build some sort of diagnostic framework into your product. What types of built-in diagnostic tools have you used or seen used? Logging seems to be the predominate method, which makes sense. We have a fairly sophisticated logging frame work in place with different levels of verbosity and the ability to filter on specific modules (actually we can filter down to the granularity of a single file). Error logs are placed strategically to manufacture a pretty good representation of a stack trace when an error occurs. We don't have the luxury of 10 million terabytes of disk space since I work on embedded platforms, so we have two ways of getting them off the system: a serial port and a syslog server. However, an issue we run into sometimes is actually getting the user to turn the logs on. Our current framework often requires some user interaction.

  Read the article

• How to get my laptop to detect SD cards inserted into its built-in card reader?

  - by Candelight

  My laptop has a built-in SD Card reader but it cannot detect one when inserted. Here is the result when I type lspci from the terminal: 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:12.0 IDE interface: ATI Technologies Inc IXP SB400 Serial ATA Controller (rev 80) 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (rev 80) 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (rev 80) 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 83) 00:14.1 IDE interface: ATI Technologies Inc IXP SB400 IDE Controller (rev 80) 00:14.2 Audio device: ATI Technologies Inc IXP SB4x0 High Definition Audio Controller (rev 01) 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge (rev 80) 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (rev 80) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS482 [Radeon Xpress 200M] 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 05:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 05:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 05:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 05:09.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g

  Read the article

• Chainloading GRUB2 from BURG

  - by WindowsEscapist

  I have an old PC with Puppy Linux in addition to Ubuntu and Windows XP. THis creates a LOT of menu entries (all of which I would like to keep): Ubuntu 10.04 Ubuntu Recovery Mode Memtest x86 Memtest Serial Windows XP Pro Precise Puppy Linux Precise Puppy TORAM Puppy 4.3.1 Puppy 4.3.1 TORAM Plop Boot Manager (for booting to USB, PC doesn't have BIOS option). Now, in my fancy shiny laptop I've gotten really attached to BURG, and would like a setup where I have a Windows icon, an Ubuntu icon, and an arrow that chainloads GRUB2 so that I can boot from USB or run Puppy if need be (all these entries will obviously not fit into the BURG theme I use, Lightness). The problem is, GRUB2 can't install the the beginning of a partition like it used to be able to (I am reluctant to specify andything with --force at the end), at least, without warning that warn: This is a BAD idea!. So I'm kind of at a loss here. I can't see how the folding option would work, because all of those other options would have the same icon once I unfolded (Lightness is non-text-based). If I do embed GRUB using grub-install /dev/sdax --force, how do I chainload it with BURG? Is there another way?

  Read the article

• Library Organization in .NET

  - by Greg Ros

  I've written a .NET bitwise operations library as part of my projects (stuff ranging from get MSB set to some more complicated bitwise transformations) and I mean to release it as free software. I'm a bit confused about a design aspect of the library, though. Many of the methods/transformations in the library come with different endianness. A simple example is a getBitAt method that regards index 0 as the least significant bit, or the most significant bit, depending on the version used. In practice, I've found that using separate functions for different endianness results in much more comprehensible and reusable code than assuming all operations are little-endian or something. I'm really stumped regarding how best to package the library. Should I have methods that have LE and BE versions take an enum parameter in their signature, e.g. Endianness.Little, Endianness.Big? Should I have different static classes with identically named methods? such as MSB.GetBit and LSB.GetBit On a much wider note, is there a standard I could use in cases like this? Some guide? Is my design issue trivial? I have a perfectionist bent, and I sometimes get stuck on tricky design issues like this... Note: I've sort of realized I'm using endianness somewhat colloquially to refer to the order/place value of digital component parts (be they bits, bytes, or words) in a larger whole, in any setting. I'm not talking about machine-level endianness or serial transmission endianness. Just about place-value semantics in general. So there isn't a context of targeting different machines/transmission techniques or something.

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Discs in DVD Drive not being read

  - by I Heart Ubuntu

  Does anyone have an experience with Ubuntu that is no longer reading discs in the DVD drive? This is my first time Ubuntu does not see the disc :| The disc is fine and works on my other Ubuntu computers. The drive is there and powered. I can even type in eject in a terminal and the drive will open. Using the command: sudo lshw -C disk I am able to see info about my drive too. Actually BOTH of my internal DVD drives cannot read discs anymore. If the output is not readable below, here is the info in pastebin. http://pastebin.com/GqqSCTPw *-cdrom:0 description: DVD writer product: DVD_RW ND-3500AG vendor: _NEC physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom1 logical name: /dev/cdrw1 logical name: /dev/dvd1 logical name: /dev/dvdrw1 logical name: /dev/scd0 logical name: /dev/sr0 version: 2.1B serial: [_NEC DVD_RW ND-3500AG2.1B06022300BT-LIGGY capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: CDDVDW SH-S222A vendor: TSSTcorp physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: SB01 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc

  Read the article

• Remote Debugging

  - by Pemdas

  Obviously, the easiest way to solve a bug is to be able to reproduce it in house. However, sometimes that is not practical. For starters, users are often not very good at providing you with useful information. Costumer Service: "what seems to be the issue?" User: "It crashed!" To further compound that, sometimes the bug only occurs under certain environmentally conditions that can not be adequately replicated in house. With that in mind, it is important to build some sort of diagnostic framework into your product. What type of solutions have you seen or used in your experience? Logging seems to be the predominate method, which makes sense. We have a fairly sophisticated logging frame work in place with different levels of verbosity and the ability to filter on specific modules (actually we can filter down to the granularity of a single file). Error logs are placed strategically to manufacture a pretty good representation of a stack trace when an error occurs. We don't have the luxury of 10 million terabytes of disk space since I work on embedded platforms, so we have two ways of getting them off the system: a serial port and a syslog server. However, an issue we run into sometimes is actually getting the user to turn the logs on. Our current framework often requires some user interaction.

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Cannot Connect Modem ( /dev/ttySL0 ) Using gnome-ppp - Dial-Up Connection

  - by nicorellius

  I'm trying to connect my Toshiba Satellite running Ubuntu 10.04 to my Eris running Android 2.1 through a Bluetooth connection and establish a dial-up connection (DUN) with the modem. I can connect my phone to my laptop, and I can detect my modem (after installing drivers), which is located at /dev/ttySL0. But when I launch gnome-ppp and enter my phone number (123 for PDA-Net) I get a dialog that says "Connecting... Sending Password" with Log and Cancel buttons. The log shows this: --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Please enter password (or empty password to stop): --> Configuration does not specify a valid login name. The PDA-Net DUN protocol is running and shows no error. Any ideas? Any help is much appreciated.

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Should you create a class within a method?

  - by Amndeep7

  I have made a program using Java that is an implementation of this project: http://nifty.stanford.edu/2009/stone-random-art/sml/index.html. Essentially, you create a mathematical expression and, using the pixel coordinate as input, make a picture. After I initially implemented this in serial, I then implemented it in parallel due to the fact that if the picture size is too large or if the mathematical expression is too complex (especially considering the fact that I made the expression recursively), it takes a really long time. During this process, I realized that I needed two classes which implemented the Runnable interface as I had to put in parameters for the run method, which you aren't allowed to do directly. One of these classes ended up being a medium sized static inner class (not large enough to make an independent class file for it though). The other though, just needed a few parameters to determine some indexes and the size of the for loop that I was making run in parallel - here it is: class DataConversionRunnable implements Runnable { int jj, kk, w; DataConversionRunnable(int column, int matrix, int wid) { jj = column; kk = matrix; w = wid; } public void run() { for(int i = 0; i < w; i++) colorvals[kk][jj][i] = (int) ((raw[kk][jj][i] + 1.0) * 255 / 2.0); increaseCounter(); } } My question is should I make it a static inner class or can I just create it in a method? What is the general programming convention followed in this case?

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

• Process Improvement and the Data Professional

  - by BuckWoody

  Don’t be afraid of that title – I’m not talking about Six Sigma or anything super-formal here. In many organizations, there are more folks in other IT roles than in the Data Professional area. In other words, there are more developers, system administrators and so on than there are the “DBA” role. That means we often have more to do than the time we need to do it. And, oddly enough, the first thing that is sacrificed is process improvement – the little things we need to do to make the day go faster in the first place. Then we get even more behind, the work piles up and…well, you know all about that. Earlier I challenged you to find 10-30 minutes a day to study. Some folks wrote back and asked “where do I start”? Well, why not be super-efficient and combine that time with learning how to make yourself more efficient? Try out a new scripting language, learn a new tool that automates things or find out ways others have automated their systems. In general, find out what you’re doing and how, and then see if that can be improved. It’s kind of like doing a performance tuning gig on yourself! If you’re pressed for time, look for bite-sized articles (like the ones I’ve done here for PowerShell and SQL Server) that you can follow in a “serial” fashion. In a short time you’ll have a new set of knowledge you can use to make your day faster. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• How do I get my programs to communicate with each other

  - by Benjamin Lindqvist

  I'm basically just getting started with programming. The problem I have with progressing is that I have a hard time learning stuff just for the sake of knowing them - I do better when there's a problem to be solved or a task to be completed so I can learn 'on the job'. So I'm interested in starting some interesting project. I know the basics of Python, Java, Matlab and some C++ aswell and I know enough about microcontrollers to make LED blink etc. The type of stuff I'm looking for is for example scraping some weather forecast site (with Python) and outputting the chance of rain to a LCD display, or a program that makes chrome open and log in to facebook if I say "HAL, time for facebook", or more generally, a program that reads serial/USB input, looks for certain sequences and sends instructions to some other program if it finds one. Do you open some kind of shared stream in which one program reads and one writes? What do I need to read up on to do accomplish this myself? I have no experience with linux or the linux terminal, but looking over peoples shoulders makes me suspect that's what people use. Is that correct?

  Read the article

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• How can I connect my USB (HP) printer in 10.4, which can't be discovered and worked in 9.x

  - by Brian

  My printer was working under 9.x. It is a an hp photosmart C3100 series. When I open the Admin- printing. no local printers are found. I try to add via other (My local choices are Serial and other). I have tried many uri's - ipp://localhost:631/ipp, http://localhost/ipp, localhost, 127.0.0.1, etc... None have worked. Under the networked I have tried JetDirect, using localhost and 127.0.0.1 and port 631. I have tried many options under IPP with different variants in the host trying to verify a printer. No luck. I tried LPD/LPR with localhost and tried the probe. no luck. I tried the cups admin via localhost:631 and that didn't work. On the old version its simply found the local printer, I might have picked the driver, I can't remember but it was the photosmart c3100 series that was working. I just can't get 10.4 to print.

  Read the article

• Where to install boot loader on a Zenbook Prime?

  - by Christians

  I cannot figure out where to install the boot loader on my Zenbook UX31A Prime. I have installed Ubuntu many times on normal hard drives, but this is the first SSD and I am struggling. Installed Ubuntu 12.04 64-bit selecting "UEFI: general" boot entry. Installation type: Something Else Created partition /sda5 mount as /, /sda6 mount as /home, /sda7 mount as swap Selected /dev/sda for boot loader installation. Other options are /dev/sda, /dev/sda1/dev/sda3 Windows 7 (loader) ... Grub comes up with 6 entries Ubuntu - this runs great Linux 3.2.0-29-generic recovery mode: mode hangs with "fb: conflicting fb hw usae interdrnfb vs EFI VGA - removing generic adapter" memtest86:erro: unknown command `linux 16' memtest86 serial: unknown command `linux 16' Windows 7 (loader) (on /dev/sda3): invalid EFI file path Windows Recovery Environment (on /dev/sda8): unknown command drivemap, invalid EFI file path. My workaround for booting Windows 7 is hitting ESC during boot, windows boot manager comes up and * for booting into Windows 7 I select "WIndows Boot Manager (PO: SanDisk ....". * for booting into Ubuntu I select ubuntu (P0: SanDisk...) How can I boot into Windows from Grub?

  Read the article

• Can't install the wireless driver in HP Pavilion dv2419us

  - by maqtanim

  I've just installed Ubuntu 13.04 in an old HP Pavilion dv2419us. The problem is, Ubuntu doesn't detect the wireless card. But it works fine in Windows 7. The following command returns nothing! lspci -vvnn | grep 14e4 And the lspci output is: 00:00.1 RAM memory: NVIDIA Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: NVIDIA Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: NVIDIA Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: NVIDIA Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: NVIDIA Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: NVIDIA Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: NVIDIA Corporation C51 [GeForce Go 6150] (rev a2) 00:09.0 RAM memory: NVIDIA Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: NVIDIA Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: NVIDIA Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: NVIDIA Corporation MCP51 PMU (rev a3) 00:0b.0 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: NVIDIA Corporation MCP51 IDE (rev f1) 00:0e.0 IDE interface: NVIDIA Corporation MCP51 Serial ATA Controller (rev f1) 00:10.0 PCI bridge: NVIDIA Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: NVIDIA Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: NVIDIA Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 05:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 05:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 05:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 05:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) The command lspci -nn | grep 0280 gives no output. Any suggestion regarding this?

  Read the article

• Wireless drivers

  - by Kencer

  The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• Installing 10.04 server on HP xw9400 Workstation with RAID 5

  - by Dave Long

  I have a workstation that was given to me that is a friggen powerhouse, so I figured I would set it up as my development and demo server. This is my first experience installing Ubuntu onto a RAID array and so far it has not been a fun one. I have been following the Advanced Installation guide for installing Ubuntu 10.04 server, and it says that there will be an option on the Partition Disks screen to manually create the partitions, but the only options I have are: Configure iSCSI volumes Undo changes to partitions Finish partitioning and write changes to disk Just before I got to that screen I got a message that said: One or more drives containing Serial ATA RAID configurations have been found. Do you wish to activate these RAID devices? It doesn't matter whether I answer yes or no to that, I still get the same Partition Disks screen. When I try to select Finish partitioning and write changes to disk I just get the No root file system error. Has anyone else experienced this, and how do I get past it? Can I not run Ubuntu on this machine?

  Read the article

• Cannot view, use, or open CDs or DVDs in Ubuntu 12.04

  - by user67592

  I am fairly new to Ubuntu 12.04 and I have encountered a rather irritating problem. Whenever I insert a CD or DVD (whether it have data, music, movies, or nothing at all), nothing pops up saying "you have inserted a CD", "play with Rhythmbox?" etc. It doesn't show the CD in the launcher/dock or anything of the sort. This is especially peculiar because not only do I have a standard IDE built-in optical drive, but I have an external USB optical drive. Neither work. In addition, whenever I go to "Computer///" and I click (double click, right click, or even left click) on "CD/DVD Drive" nothing happens, when I right click and select "Open" nothing happens either [for either of the two drives (both are listed in Computer///)] And if I insert a blank disk and go to a disk burning program such as Brasero, and try to burn to the drive it detects no CDs or DVDs of any kind. I'm rather stumped and can't seem to find a question similar to this. :( Thanks for all your help in advance!! :) ~Preston Output of sudo lshw *-cdrom description: DVD-RAM writer product: CD/DVDW TS-H652M vendor: TSSTcorp physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 0414 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom description: DVD reader product: DVD Writer 300n vendor: HP physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/sr1 version: 1.25 serial: [ capabilities: removable audio cd-r cd-rw dvd configuration: status=nodisc

  Read the article

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >