Search Results

Search found 586 results on 24 pages for '802 11n'.

Page 6/24 | < Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >

• Wireless speed drops over time and doesn't get up if not reconnected

  - by Vili Lehto

  I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

  Read the article

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• Wireless does not work anymore after software update with Ubuntu 12.10 on a Dell Latitude E6230

  - by Andy

  I just installed Ubuntu 12.10 on my DELL Latitude E6230, on first boot wifi worked properly but when I updated the software it stopped working. I can't figure out the problem... The wireless network controller is a Broadcom Corporation BCM4313 802.11b/g/n Wireless Lan Controller (rev 01) "lshw -class network" gives, for the above controller: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7d00000-f7d03fff After reading the answer to another similar question, I edited the file NetworkManager.conf to make "managed=true", but that did not make any difference, it is as if the wireless adapter were not there. In the "Network" setting window, I only see "Wired" and "Network proxy". Wireless has just disappeared: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no and that's it! Nothing about the wireless controller... Any suggestions?

  Read the article

• Hostapd to connect laptop to Android

  - by Kmegamind

  i am trying to set up my laptop as an access point for my Android to use WiFi, so i knew that ubuntu sets the network as Ad-Hoc which is not discoverable by android, So i tried the method explained here -which i found on many other websites- but when i run hostapd.conf this error appears : nl80211: Failed to set interface wlan0 into AP mode nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0x8e488f8 user_data=0x8e48ea0 handler=0x807c5e0 ELOOP: remaining socket: sock=6 eloop_data=0x8e4aca8 user_data=(nil) handler=0x8086770 this is how my hostapd.conf looks like : interface=wlan0 driver=nl80211 ssid=Any_SSID_name hw_mode=g channel=1 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=Any_password wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP and this is my wireless card info : description: Wireless interface product: BCM43225 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:73:51:f1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:f0300000-f0303fff

  Read the article

• Slow wireless about 1/3 bandwidth of wired from cable modem

  - by Rhino

  HP DV6000 Wireless G Broadcom Netgear WNDR3400 router properly configured. Windows laptops using wireless G and N are considerably faster than mine. 12.04 LTS, all restricted drivers and all up to date. 50Mbps wired and 9-21 Mbps wireless on Ubuntu. 00:14.0 Bridge [0680]: NVIDIA Corporation MCP51 Ethernet Controller [10de:0269] (rev a3) Subsystem: Hewlett-Packard Company Presario V6133CL [103c:30b7] Kernel driver in use: forcedeth 03:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11a/b/g [14e4:4312] (rev 02) Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1370] Kernel driver in use: wl

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• If I enable/disable my wireless device, my computer will panic

  - by Yinyanghu

  Now, I use Debian 6.0.6 instead of Fedora 16/17. But I still sustain the problem of my wireless problem. If I enable/disable my laptop wireless device or my usb wifi adaptor, my laptop will panic. It seems like all the processes stop at that time and I have to restart my laptop directly. P.S. I think I installed the drivers correctly and the linux kernel may have some bugs. For example, when I unplug my usb wifi adaptor or I use this command, ifdown wlan0 I encounter this problem. Wireless Device: PCI: 03:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) USB: Bus 002 Device 005: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• ash scripting: space-containing variable refuses to be grepped

  - by Luci Sandor

  I am trying to run the script listed at http://talk.maemo.org/showthread.php?t=70866&page=2 on its intended hardware, a Nokia Linux phone running BusyBox ash. The script receives the name of WiFi network as a parameter, and tries to connect the phone to it. I suspect the script works, but my SSID, BU (802.1x), has space and parentheses in it. So when I type at the command prompt autoconnect.sh BU\ \(802.1x\) I get various errors. First, LIST=`iwconfig wlan0 | awk -F":" '/ESSID/{print $2}'` if [ $LIST = "\"$1\"" ]; then ...fails, even I am connected to the network. The error is not avoided by using single or double quotes instead of escaping characters at the command prompt. Second, if [ -z `iwlist wlan0 scan | grep -m 1 -o \"$1\"` ]; then echo SSID \"$1\" not found; shows that grep does not find the string, although the same grep, typed directly into the command prompt, does find 'BU (802.1x)'. How do I quote $1 in the two circumstances above so that it will work with my network SSID, containing spaces and parentheses? Thank you.

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• wifi hardware switch doesn't work on a Dell 1018

  - by user42566

  I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

  Read the article

• Wireless doesn't work on a Broadcom BCM4312

  - by Boderick

  As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

• No Wireless Networks, BCM4313 [duplicate]

  - by TalonPlz

  This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

  Read the article

• HTML form with table cell height problem

  - by Parhs

  Hello.. I have several forms like this: <table width="100%" border="0" cellpadding="0" cellspacing="0" class="table_std"> <tr id="exam_String_newValue_row"> <td width="150" class="table_defaultHeaderColumn">????a????sµ??? ??µ??</td> <td width="802" class="table_defaultHeaderColumn" > <textarea name="textarea" id="textarea" cols="45" rows="5"></textarea> </td> </tr> <tr> <td width="150" class="table_defaultHeaderColumn">??????s? - ??????</td> <td width="802"> <input name="Exam_String_value" type="text" style="width:600px" id="textfield2" /> </td> </tr> <tr> <td width="150" class="table_defaultHeaderColumn">??????s? - ?e?d??</td> <td width="802"> <input name="Exam_String_value" type="text" style="width:600px" id="textfield2" /> </td> </tr> </table> css .table_defaultHeaderColumn { font-size: 11px; } .input_std { width: 200px; } .input_small { width: 4em; } .table_std { border-collapse:collapse; } .table_std td { padding-top: 1px; padding-bottom: 1px; } The problem is the height of the cells.... isnt equal in all browsers... any solution?

  Read the article

• Mac OS X: How do I disable SSID Broadcasting with Internet Sharing over Airport?

  - by Jack Chu

  I'm currently using Internet Sharing from my Ethernet over Airport on my Macbook Pro, however I don't want my SSID broadcasted†. There doesn't seem to be an option in Sharing/System Preferences to hide my ssid or prevent broadcasting. Any ideas? † My parent's restaurant has a wifi router, but it's on the roof level where the cable was installed. The signal it gets is weak, but works for the macbook. Their iPhones and 802.11G based computers can't get the wifi connection, maybe 802.11N on the macbook gets better penetration. I figure they could use the airport sharing from the laptop. For a restaurant type setting I don't think having WPA or WPA2 is super important. There's nothing sensitive or insecure on the network, so I figure hiding the SSID would be good enough for their purposes. It's not even active 100% of the time.

  Read the article

• wifi not recognized

  - by pumper

  I had wifi and worked then some day ubuntu asked me to update some packeages and restarted the system and after that no wifi. this is my wireless_script output : ########## wireless info START ########## ##### release ##### Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty ##### kernel ##### Linux S510p 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ##### lspci ##### 02:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Lenovo Device [17aa:3026] Kernel driver in use: ath9k 03:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8162 Fast Ethernet [1969:1090] (rev 10) Subsystem: Lenovo Device [17aa:3807] Kernel driver in use: alx ##### lsusb ##### Bus 001 Device 006: ID 0eef:a111 D-WAV Scientific Co., Ltd Bus 001 Device 007: ID 0cf3:3004 Atheros Communications, Inc. Bus 001 Device 004: ID 174f:1488 Syntek Bus 001 Device 003: ID 03f0:5607 Hewlett-Packard Bus 001 Device 002: ID 8087:8000 Intel Corp. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 002: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub ##### PCMCIA Card Info ##### ##### rfkill ##### 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no ##### iw reg get ##### country 00: (2402 - 2472 @ 40), (3, 20) (2457 - 2482 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS (2474 - 2494 @ 20), (3, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS (5170 - 5250 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS (5735 - 5835 @ 40), (3, 20), PASSIVE-SCAN, NO-IBSS ##### interfaces ##### # interfaces(5) file used by ifup(8) and ifdown(8) auto lo iface lo inet loopback auto dsl-provider iface dsl-provider inet ppp pre-up /sbin/ifconfig wlan0 up # line maintained by pppoeconf provider dsl-provider auto wlan0 iface wlan0 inet manual ##### iwconfig ##### wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off ##### route ##### Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface ##### resolv.conf ##### ##### nm-tool ##### NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: alx State: unavailable Default: no HW Address: <MAC address removed> Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: unmanaged Default: no HW Address: <MAC address removed> Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points ##### NetworkManager.state ##### [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true ##### NetworkManager.conf ##### [main] plugins=ifupdown,keyfile,ofono dns=dnsmasq no-auto-default=<MAC address removed>, [ifupdown] managed=false ##### iwlist ##### wlan0 Scan completed : Cell 01 - Address: <MAC address removed> Channel:1 Frequency:2.412 GHz (Channel 1) Quality=55/70 Signal level=-55 dBm Encryption key:on ESSID:"mohsen" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000076c342498 Extra: Last beacon: 12ms ago IE: Unknown: 00066D6F6873656E IE: Unknown: 010882848B960C121824 IE: Unknown: 030101 IE: Unknown: 2A0104 IE: Unknown: 32043048606C ##### iwlist channel ##### wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz ##### lsmod ##### ath3k 13318 0 bluetooth 395423 23 bnep,ath3k,btusb,rfcomm ath9k 164164 0 ath9k_common 13551 1 ath9k ath9k_hw 453856 2 ath9k_common,ath9k ath 28698 3 ath9k_common,ath9k,ath9k_hw mac80211 626489 1 ath9k cfg80211 484040 3 ath,ath9k,mac80211 ##### modinfo ##### filename: /lib/modules/3.13.0-24-generic/kernel/drivers/bluetooth/ath3k.ko firmware: ath3k-1.fw license: GPL version: 1.0 description: Atheros AR30xx firmware driver author: Atheros Communications srcversion: 98A5245588C09E5E41690D0 alias: usb:v0489pE036d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE03Cd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE02Cd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE003d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3121d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3402d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04C5p1330d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE04Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE056d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE04Ed*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3393d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE057d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0930p0220d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0930p0219d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE005d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE004d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3362d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3008d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3006d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3005d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v04CAp3004d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3375d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p817Ad*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p311Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3008d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3004d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p0036d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v03F0p311Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE027d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0489pE03Dd*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0930p0215d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v13D3p3304d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3pE019d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3002d*dc*dsc*dp*ic*isc*ip*in* alias: usb:v0CF3p3000d*dc*dsc*dp*ic*isc*ip*in* depends: bluetooth intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko license: Dual BSD/GPL description: Support for Atheros 802.11n wireless LAN cards. author: Atheros Communications srcversion: BAF225EEB618908380B28DA alias: platform:qca955x_wmac alias: platform:ar934x_wmac alias: platform:ar933x_wmac alias: platform:ath9k alias: pci:v0000168Cd00000036sv*sd*bc*sc*i* alias: pci:v0000168Cd00000036sv0000185Fsd00003027bc*sc*i* alias: pci:v0000168Cd00000036sv00001B9Asd00002810bc*sc*i* alias: pci:v0000168Cd00000036sv0000144Fsd00007202bc*sc*i* alias: pci:v0000168Cd00000036sv00001A3Bsd00002130bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000612bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000652bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000642bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd0000302Cbc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003027bc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Ebc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Dbc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Cbc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Bbc*sc*i* alias: pci:v0000168Cd00000036sv0000144Dsd0000411Abc*sc*i* alias: pci:v0000168Cd00000036sv00001028sd0000020Ebc*sc*i* alias: pci:v0000168Cd00000036sv0000103Csd0000217Fbc*sc*i* alias: pci:v0000168Cd00000036sv0000103Csd000018E3bc*sc*i* alias: pci:v0000168Cd00000036sv000017AAsd00003026bc*sc*i* alias: pci:v0000168Cd00000036sv00001A3Bsd0000213Abc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000662bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000672bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000622bc*sc*i* alias: pci:v0000168Cd00000036sv0000185Fsd00003028bc*sc*i* alias: pci:v0000168Cd00000036sv0000105Bsd0000E069bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd0000302Bbc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003026bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003025bc*sc*i* alias: pci:v0000168Cd00000036sv00001B9Asd00002812bc*sc*i* alias: pci:v0000168Cd00000036sv00001B9Asd00002811bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00006671bc*sc*i* alias: pci:v0000168Cd00000036sv000011ADsd00000632bc*sc*i* alias: pci:v0000168Cd00000036sv0000185Fsd0000A119bc*sc*i* alias: pci:v0000168Cd00000036sv0000105Bsd0000E068bc*sc*i* alias: pci:v0000168Cd00000036sv00001A3Bsd00002176bc*sc*i* alias: pci:v0000168Cd00000036sv0000168Csd00003028bc*sc*i* alias: pci:v0000168Cd00000037sv*sd*bc*sc*i* alias: pci:v0000168Cd00000034sv*sd*bc*sc*i* alias: pci:v0000168Cd00000034sv000010CFsd00001783bc*sc*i* alias: pci:v0000168Cd00000034sv000014CDsd00000064bc*sc*i* alias: pci:v0000168Cd00000034sv000014CDsd00000063bc*sc*i* alias: pci:v0000168Cd00000034sv0000103Csd00001864bc*sc*i* alias: pci:v0000168Cd00000034sv000011ADsd00006641bc*sc*i* alias: pci:v0000168Cd00000034sv000011ADsd00006631bc*sc*i* alias: pci:v0000168Cd00000034sv00001043sd0000850Ebc*sc*i* alias: pci:v0000168Cd00000034sv00001A3Bsd00002110bc*sc*i* alias: pci:v0000168Cd00000034sv00001969sd00000091bc*sc*i* alias: pci:v0000168Cd00000034sv000017AAsd00003214bc*sc*i* alias: pci:v0000168Cd00000034sv0000168Csd00003117bc*sc*i* alias: pci:v0000168Cd00000034sv000011ADsd00006661bc*sc*i* alias: pci:v0000168Cd00000034sv00001A3Bsd00002116bc*sc*i* alias: pci:v0000168Cd00000033sv*sd*bc*sc*i* alias: pci:v0000168Cd00000032sv*sd*bc*sc*i* alias: pci:v0000168Cd00000032sv00001043sd0000850Dbc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00001C01bc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00001C00bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001F95bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001195bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001F86bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001186bc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00002001bc*sc*i* alias: pci:v0000168Cd00000032sv00001B9Asd00002000bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Fsd00007197bc*sc*i* alias: pci:v0000168Cd00000032sv0000105Bsd0000E04Fbc*sc*i* alias: pci:v0000168Cd00000032sv0000105Bsd0000E04Ebc*sc*i* alias: pci:v0000168Cd00000032sv000011ADsd00006628bc*sc*i* alias: pci:v0000168Cd00000032sv000011ADsd00006627bc*sc*i* alias: pci:v0000168Cd00000032sv00001C56sd00004001bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002100bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002C97bc*sc*i* alias: pci:v0000168Cd00000032sv000017AAsd00003219bc*sc*i* alias: pci:v0000168Cd00000032sv000017AAsd00003218bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000C708bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000C680bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000C706bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000410Fbc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000410Ebc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd0000410Dbc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd00004106bc*sc*i* alias: pci:v0000168Cd00000032sv0000144Dsd00004105bc*sc*i* alias: pci:v0000168Cd00000032sv0000185Fsd00003027bc*sc*i* alias: pci:v0000168Cd00000032sv0000185Fsd00003119bc*sc*i* alias: pci:v0000168Cd00000032sv0000168Csd00003122bc*sc*i* alias: pci:v0000168Cd00000032sv0000168Csd00003119bc*sc*i* alias: pci:v0000168Cd00000032sv0000105Bsd0000E075bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002152bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd0000126Abc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002126bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00001237bc*sc*i* alias: pci:v0000168Cd00000032sv00001A3Bsd00002086bc*sc*i* alias: pci:v0000168Cd00000030sv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Esv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Dsv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Csv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Bsv*sd*bc*sc*i* alias: pci:v0000168Cd0000002Bsv00001A3Bsd00002C37bc*sc*i* alias: pci:v0000168Cd0000002Asv000010CFsd00001536bc*sc*i* alias: pci:v0000168Cd0000002Asv000010CFsd0000147Dbc*sc*i* alias: pci:v0000168Cd0000002Asv000010CFsd0000147Cbc*sc*i* alias: pci:v0000168Cd0000002Asv0000185Fsd0000309Dbc*sc*i* alias: pci:v0000168Cd0000002Asv00001A32sd00000306bc*sc*i* alias: pci:v0000168Cd0000002Asv000011ADsd00006642bc*sc*i* alias: pci:v0000168Cd0000002Asv000011ADsd00006632bc*sc*i* alias: pci:v0000168Cd0000002Asv0000105Bsd0000E01Fbc*sc*i* alias: pci:v0000168Cd0000002Asv00001A3Bsd00001C71bc*sc*i* alias: pci:v0000168Cd0000002Asv*sd*bc*sc*i* alias: pci:v0000168Cd00000029sv*sd*bc*sc*i* alias: pci:v0000168Cd00000027sv*sd*bc*sc*i* alias: pci:v0000168Cd00000024sv*sd*bc*sc*i* alias: pci:v0000168Cd00000023sv*sd*bc*sc*i* depends: ath9k_hw,mac80211,ath9k_common,cfg80211,ath intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 parm: debug:Debugging mask (uint) parm: nohwcrypt:Disable hardware encryption (int) parm: blink:Enable LED blink on activity (int) parm: btcoex_enable:Enable wifi-BT coexistence (int) parm: bt_ant_diversity:Enable WLAN/BT RX antenna diversity (int) parm: ps_enable:Enable WLAN PowerSave (int) filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko license: Dual BSD/GPL description: Shared library for Atheros wireless 802.11n LAN cards. author: Atheros Communications srcversion: 696B00A6C59713EC0966997 depends: ath,ath9k_hw intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko license: Dual BSD/GPL description: Support for Atheros 802.11n wireless LAN cards. author: Atheros Communications srcversion: 4809F3842A0542CD6B556D3 depends: ath intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 filename: /lib/modules/3.13.0-24-generic/kernel/drivers/net/wireless/ath/ath.ko license: Dual BSD/GPL description: Shared library for Atheros wireless LAN cards. author: Atheros Communications srcversion: 88A67C5359B02C5A710AFCF depends: cfg80211 intree: Y vermagic: 3.13.0-24-generic SMP mod_unload modversions signer: Magrathea: Glacier signing key sig_key: <MAC address removed>:D9:06:21:70:6E:8D:06:60:4D:73:0B:35:9F:C0 sig_hashalgo: sha512 ##### modules ##### lp rtc ##### blacklist ##### [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac [/etc/modprobe.d/fbdev-blacklist.conf] blacklist arkfb blacklist aty128fb blacklist atyfb blacklist radeonfb blacklist cirrusfb blacklist cyber2000fb blacklist gx1fb blacklist gxfb blacklist kyrofb blacklist matroxfb_base blacklist mb862xxfb blacklist neofb blacklist nvidiafb blacklist pm2fb blacklist pm3fb blacklist s3fb blacklist savagefb blacklist sisfb blacklist tdfxfb blacklist tridentfb blacklist viafb blacklist vt8623fb ##### udev rules ##### # PCI device 0x1969:0x1090 (alx) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="<MAC address removed>", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" # PCI device 0x168c:0x0036 (ath9k) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="<MAC address removed>", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0" ##### dmesg ##### [ 1.707662] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f03) [ 11.918852] ath: phy0: WB335 1-ANT card detected [ 11.918856] ath: phy0: Set BT/WLAN RX diversity capability [ 11.926438] ath: phy0: Enable LNA combining [ 11.928469] ath: phy0: ASPM enabled: 0x42 [ 11.928473] ath: EEPROM regdomain: 0x65 [ 11.928475] ath: EEPROM indicates we should expect a direct regpair map [ 11.928478] ath: Country alpha2 being used: 00 [ 11.928479] ath: Regpair used: 0x65 [ 14.066021] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready ########## wireless info END ############

  Read the article

• hp pavilion g6 1250 with a BCM 4313 doesn't see any wireless networks

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation, ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) There are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• wireless detected but Can't connect to network, Wifi card intel pro wireless N100 BGN

  - by Alexandre777

  Thanks in advance, I installed Linux Mint kernel 3.0.0-12 x64 ,wireless is detected and I configure it in network manager but can't coonect, there are the results of command line: $ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ sudo lshw -C network** *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:51:c9:d6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:d7400000-d7401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:5b:39:99:8f:16 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Thank you.

  Read the article

• hp pavilion g6 1250 wireless problems

  - by Ahmed Kotb

  i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation , ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) there are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Atheros wireless not working

  - by Chandru1

  I have been struggling hard since i have installed Ubuntu 10.10 but it has been difficult for me to get my wifi working. So here is what i tried. First i checked whether i have the driver using the ifconfig command and it shows the wireless lan driver as wlan0. Next, i tried the command iwlist wlan0 scanning by becoming the root which gave me the output as no scan results. Next, i visited this link https://help.ubuntu.com/community/WifiDocs/Driver/Atheros to see as to what problem my laptop may have. I do own have an ath5k chipset. And as i followed the instructions in the above link in one of the blacklist-ath_pci.conf file had this written in it. For some Atheros 5K RF MACs, the madwifi driver loads buts fails to correctly initialize the hardware, leaving it in a state from which ath5k cannot recover. To prevent this condition, stop madwifi from loading by default. Use Jockey to select one driver or the other. (Ubuntu: #315056, #323830 I am not that good at Linux but i have given it a try. I am desperate to have my wifi working and i would be glad if this community could help. ADDED: If anyone would like to know as to what drivers i am using this is the output. network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wlan0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath5k driverversion=2.6.35-24-generic firmware=N/A latency=168 link=no maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11bg resources: irq:18 memory:d0000000-d000ffff Some more information and output as to what i have done. lsmod | grep ath ath5k 130083 0 mac80211 231541 1 ath5k ath 8153 1 ath5k cfg80211 144470 3 ath5k,mac80211,ath led_class 2633 1 ath5k

  Read the article

• Are there open source Linux drivers for the Panda Wifi USB adapter?

  - by Zifre

  I'm looking for a wireless adapter for my new PC. My requirements are: it supports 802.11n it is cheap (under 30 USD) it has good, open source Linux drivers (will work "out of the box") preferably USB, but PCI is okay too I found the Panda Wifi (b/g/n) 150Mbps Wireless-N (802.11n) USB Adapter. It says there is Linux support. However, I want to make sure there are open source drivers included with the Linux kernel. Does anyone know what the chipset for this adapter is? What driver it would use?

  Read the article

• Why Wifi no longer works 12.04.1

  - by Roger

  starting this morning over wifi (Realtek RTL8188CE) on CLEVO W253HU. May be due to the update before yesterday, more pilot managed, but somehow it worked yesterday. If someone has an idea of the problem. Back command lines: cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.1 LTS" lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 006: ID 192f:0416 Avago Technologies, Pte. Bus 002 Device 004: ID 5986:0315 Acer, Inc lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) lspci -nn | grep -i net 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) 03:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) lspci -k 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: i2c-i801 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device 9196 Kernel modules: rtl8192ce 03:00.0 Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jme Kernel modules: jme 03:00.1 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: sdhci-pci Kernel modules: sdhci-pci 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel modules: sdhci-pci 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 90) Subsystem: CLEVO/KAPOK Computer Device 4140 Kernel driver in use: jmb38x_ms Kernel modules: jmb38x_ms sudo lshw -C network *-network NON-RÉCLAMÉ description: Network controller produit: RTL8188CE 802.11b/g/n WiFi Adapter fabriquant: Realtek Semiconductor Co., Ltd. identifiant matériel: 0 information bus: pci@0000:02:00.0 version: 01 bits: 64 bits horloge: 33MHz fonctionnalités: pm msi pciexpress cap_list configuration: latency=0 ressources: portE/S:e000(taille=256) mémoire:f7d00000-f7d03fff *-network description: Ethernet interface produit: JMC250 PCI Express Gigabit Ethernet Controller fabriquant: JMicron Technology Corp. identifiant matériel: 0 information bus: pci@0000:03:00.0 nom logique: eth0 version: 05 numéro de série: 00:90:f5:c1:c6:45 taille: 100Mbit/s capacité: 1Gbit/s bits: 32 bits horloge: 33MHz fonctionnalités: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=full ip=192.168.1.54 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s ressources: irq:44 mémoire:f7c20000-f7c23fff portE/S:d100(taille=128) portE/S:d000(taille=256) mémoire:f7c10000-f7c1ffff mémoire:f7c00000-f7c0ffff lsmod Module Size Used by btusb 18288 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 11 btusb,rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 binfmt_misc 17540 1 snd_hda_codec_realtek 224173 0 dm_crypt 23125 0 snd_hda_codec_hdmi 32474 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_hda_intel 33773 2 snd_hda_codec 127706 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi jmb38x_ms 17646 0 psmouse 87692 0 serio_raw 13211 0 memstick 16569 1 jmb38x_ms snd_seq_midi_event 14899 1 snd_seq_midi rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi mac_hid 13253 0 snd 78855 14 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 205544 2 rtlwifi,mac80211 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid i915 473035 3 drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper jme 41259 0 i2c_algo_bit 13423 1 i915 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci wmi 19256 0 video 19596 1 i915 iwconfig lo no wireless extensions. eth0 no wireless extensions. ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:c1:c6:45 inet adr:192.168.1.54 Bcast:192.168.1.255 Masque:255.255.255.0 adr inet6: fe80::290:f5ff:fec1:c645/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:4513 erreurs:0 :0 overruns:0 frame:0 TX packets:4359 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:3471675 (3.4 MB) Octets transmis:712722 (712.7 KB) Interruption:44 lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 Packets reçus:686 erreurs:0 :0 overruns:0 frame:0 TX packets:686 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 Octets reçus:64556 (64.5 KB) Octets transmis:64556 (64.5 KB) sudo iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. uname -r -m 3.2.0-30-generic x86_64 cat /etc/network/interfaces auto lo iface lo inet loopback nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Connexion filaire 1] ------------------------------------------ Type: Wired Driver: jme State: connected Default: yes HW Address: 00:90:F5:C1:C6:45 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.54 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 sudo rfkill listrfkill list 1: hci0: Bluetooth Soft blocked: no Hard blocked: no The absence of line "Kernel driver in use:" the return of lspci-k made ??me think that it is not loaded yet but he seems to be. lsmod | grep rtl8192ce rtl8192ce 137478 0 rtlwifi 118749 1 rtl8192ce mac80211 506816 2 rtl8192ce,rtlwifi I found something disturbing in / var / log / syslog Sep 14 11:40:11 pcroger kernel: [ 64.048783] rtl8192ce-0:rtl92c_init_sw_vars():<0-0> Failed to request firmware! Sep 14 11:40:11 pcroger kernel: [ 64.048795] rtlwifi-0:rtl_pci_probe():<0-0> Can't init_sw_vars. Sep 14 11:40:11 pcroger kernel: [ 64.048835] rtl8192ce 0000:02:00.0: PCI INT A disabled Sep 14 11:40:11 pcroger kernel: [ 64.943345] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6 frozen Sep 14 11:40:11 pcroger kernel: [ 64.943358] ata1.00: failed command: READ FPDMA QUEUED Sep 14 11:40:11 pcroger kernel: [ 64.943371] ata1.00: cmd 60/00:00:00:68:6a/04:00:0b:00:00/40 tag 0 ncq 524288 in Sep 14 11:40:11 pcroger kernel: [ 64.943374] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) Sep 14 11:40:11 pcroger kernel: [ 64.943381] ata1.00: status: { DRDY } Ubuntu and takes forever to start (2 min).

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Macintosh computers cannot connect to router unless we re-start the modem and router

  - by dwwilson66

  We have a small office network with DSL and a Netgear WNR-2000 wireless router acting as a DHCP server. There are nine devices connected to the router, wirelessly and wired. Whenever a Mac computer tries to connect, it's unsuccessful until we restart the router. Each of the possible devices that can connect to the network is listed in a table to assign certain IP addresses to certain MAC addresses. I am running WPA-PSK security. I can view the router status and see that the Mac's MAC address is visible to the router, but with a 169.* IP address, even though I'm assigning its MAC address to an IP address within my subnet. All non-Mac devices attached to the network connect properly, and can access the network properly even AFTER the Mac has not successfully connected. The network includes Windows devices, Roku boxes, printers and internet ready TVs. This to me, would point to a DHCP issue with how Mac communicates with my network. One interesting thing to note is that if a Mac connects and is prevented from sleeping, it will stay connected indefinitely; reissuing the security cert from the router works fine. I'm not sure if that's supposed to sever & re-establish a connection with the updated credentials or not, but I do stay connected. If the Mac sleeps and is awakened while the security cert is still valid, it connects fine. If the security certificate expires while the Mac is asleep, we need to restart the router. Restarting the router will ALWAYS assigns the proper IP addresses to the Mac equipment. I have heard anecdotally that Mac doesn't play well with 802.11n; I have not tested any other Wireless protocols. There's a couple issues here: First, I found this on Stack, Mac laptop crashing wireless router, but it's not rally applicable since the router isn't crashing. But, it does give some clues about Mac's accessing the network. I did change my encryption from WEP to WPA-PSK, but after about a week, we're still experiencing the issue. I'm not really sure if there's anything else useful in that question. Second, I'm considering getting a 802.11c router and hooking it up to the wireless N router. the 802.11c router would handle all the Mac traffic, and would be set up as a Mac-only subnet. Everything else would remain as is. However, I'm not sure if this is doable on a technology level...do I need a bridge or is this some way to do this with regular consumer gear?

  Read the article

• Use Network-Manager to Connect to a wifi Access Point on the command-line

  - by Stefano Palazzo

  I'd like to connect to a wireless access point from the command-line. ideally, I'd only need the name of the AP. But the hardware-address would work as well. I know I can use nmcli to connect to a managed network connection, but in my case, the access point may not be configured for Network-Manager yet (See the difference between the output of nm-tool and nmcli con). Example output of nmcli: Auto pwln 3a3d62b1-bbdf-4f76-b4d2-c211fd5cfb03 802-11-wireless [...] Wired Network aa586921-accf-4932-98c4-c873c310f08e 802-3-ethernet [...] Cisco-UDP Uni 7f94847b-04dc-40b7-9955-5246fb77cc65 vpn [...] T-mobile (D1) 867f345a-cbbf-4bd4-b883-a5e5ae0932f0 gsm [...] Example output of nm-tool: State: connected - Device: eth1 [Auto pwln] ---------------------------------------------------- [...] Wireless Access Points (* = current AP) *pwln: Infra, [...], Freq 2472 MHz, Rate 54 Mb/s, Strength 80 WPA WPA2 WLAN: Infra, [...], Freq 2422 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 [...] How do I connect to an access point that may or may not be known to NM? Extra: Finding out if the connection needs a pass-phrase, and submitting it on the command-line as well would be great too (that is to say It'd be nice if network-manager wouldn't pop open any keyring dialogues or errors on the gui)

  Read the article

< Previous Page | 2 3 4 5 6 7 8 9 10 11 12 13  | Next Page >