Search Results

Search found 624 results on 25 pages for 'dumb'.

Page 9/25 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• What's a good public access terminal solution using old PCs and remote VMs?

  - by greenfingers

  Has anyone had experience using VMs as remote desktops for public access terminals (e.g. an internet cafe) In our case we don't want to charge money for access but I figure this solution has a few advantages, such as: can easily re-build VMs daily, erasing private data and clutter can use rickety old PCs for the 'dumb' terminals less IT support needed on site Can you suggest tools to help do this? Keeping the terminals up and running as much of the time as possible is the main priority, so they need to boot straight into full screen remote desktop and stay there.

  Read the article

• Add static ARP entries when network is brought up

  - by jozzas

  I have some pretty dumb IP devices on a subnet with my Ubuntu server, and the server receives streaming data from each device. I have run into a problem in that when an ARP request is issued to the device while it is streaming data to the server, the request is ignored, the cache entry times out and the server stops receiving the stream. So, to prevent the server from sending ARP requests to these devices altogether, I would like to add a static ARP entry for each, something like arp -i eth2 -s ip.of.the.device mac:of:the:device But these "static" ARP entries are lost if networking is disabled / enabled or if the server is rebooted. Where is the best place to automatically add these entries, preferably somewhere that will re-add them every time the interface eth2 is brought up? I really don't want to have to write a script that monitors the output of arp and re-adds the cache entries if they're missing. Edit to add what my final script was: Created the file /etc/network/if-up.d/add-my-static-arp With the contents: #!/bin/sh arp -i eth0 -s 192.168.0.4 00:50:cc:44:55:55 arp -i eth0 -s 192.168.0.5 00:50:cc:44:55:56 arp -i eth0 -s 192.168.0.6 00:50:cc:44:55:57 And then obviously add the permission to allow it to be executed: chmod +x /etc/network/if-up.d/add-my-static-arp And these arp entries will be manually added or re-added every time any network interface is brought up.

  Read the article

• Fuzzing for Security

  - by Sylvain Duloutre

  Yesterday, I attended an internal workshop about ethical hacking. Hacking skills like fuzzing can be used to quantitatively assess and measure security threats in software.  Fuzzing is a software testing technique used to discover coding errors and security loopholes in software, operating systems or networks by injecting massive amounts of random data, called fuzz, to the system in an attempt to make it crash. If the program contains a vulnerability that can leads to an exception, crash or server error (in the case of web apps), it can be determined that a vulnerability has been discovered.A fuzzer is a program that generates and injects random (and in general faulty) input to an application. Its main purpose is to make things easier and automated.There are typically two methods for producing fuzz data that is sent to a target, Generation or Mutation. Generational fuzzers are capable of building the data being sent based on a data model provided by the fuzzer creator. Sometimes this is simple and dumb as sending random bytes, swapping bytes or much smarter by knowing good values and combining them in interesting ways.Mutation on the other hand starts out with a known good "template" which is then modified. However, nothing that is not present in the "template" or "seed" will be produced.Generally fuzzers are good at finding buffer overflow, DoS, SQL Injection, Format String bugs etc. They do a poor job at finding vulnerabilites related to information disclosure, encryption flaws and any other vulnerability that does not cause the program to crash.  Fuzzing is simple and offers a high benefit-to-cost ratio but does not replace other proven testing techniques.What is your computer doing over the week-end ?

  Read the article

• Google search question, front page not showing...

  - by Catelyn

  I know this is probably a dumb question but I hope someone can give me some insight; I was ranked on Google first page of search results for "funny st patricks day shirts" but I was third from the bottom and not familiar enough with SEO, so I signed up for "Attracta" to rank higher. Big mistake. Since using Attracta, I've lost the first page and I'm now on the fourth page in that search. What I noticed is that Google is now just showing a sub-page or side page, (a link from my front page, to a page which has only a few designs in it) this is not where I would want customers to land first... but my front page is not showing in that search anymore. Obviously, the title of this side page is not geared toward that search result, so I know that's why I have the pr drop. Why is my front page not ranking over that page, though? Why is it apparently gone from that search, or so far back no one will ever find it? I need to know how to fix this quick if anyone has any advice at all for me. It's the busiest season for my website and the people who were stealing design ideas from me are all ranked higher than my site now. (I can prove this, lol) So, I'm very frustrated by that. I would be very grateful to have any advice at all as to what I can do to fix this. THANKS in advance for any advice you can offer. Catelyn

  Read the article

• If statement causing xna sprites to draw frame by frame

  - by user1489599

  I’m a bit new to XNA but I wanted to write a simple program that would fire a cannon ball from a cannon at a 45 degree angle. It works fine outside of my keyboard i/o if statement, but when I encapsulate the code around an if statement checking to see if the user hits the space bar, the sprite will draw one frame at a time every time the space bar is hit. This is the code in question if (currentKeyboardState.IsKeyUp(Keys.Space) && previousKeyboardState.IsKeyDown(Keys.Space) && !skullBall.Alive) { //works outside the keyboard input if statement //{ skullBall.Position = cannon.Position; skullBall.DeltaY = -(float)(Math.Sin(MathHelper.ToRadians(45)) * 50/*39.7577*/ * time + 0.5 * (gravity * (time * time))); skullBall.DeltaX = (float)(Math.Cos(MathHelper.ToRadians(45)) * 50/*39.7577*/ * time); skullBall.Alive = true; //} } The skull ball represents the cannon ball and the cannon is just the starting point. DeltaX and DeltaY are the values I’m using to update the cannon balls position per update. I know it's dumb to have the cannon ball start at the cannons position every time the update is called but it’s not really noticeable right now. I was wondering if after examining my code, if anyone noticed any errors that would cause the sprite to display frame by frame instead of drawing it as a full animation of the cannon ball leaving the cannon and moving from there.

  Read the article

• How do I prevent rpmbuild form injecting requirements into RPM package?

  - by Basilevs

  I'm creating an RPM package from native Python 2.5 one. Out corporate policy is to use python2.4 by default, so I'm adding a string Requires: python25 to a .spec file. When I look at created RPM file though, i see the following dependencies: rpm -qR -p ZSI-2.1_a1-py25.noarch.rpm /usr/bin/python2.5 python(abi) = 2.5 python25 rpmlib(CompressedFileNames) <= 3.0.4-1 rpmlib(PayloadFilesHavePrefix) <= 4.0-1 Dependency added by me is present, but other dependencies are also here. I'm unable to provide python(abi) = 2.5 dependency, because of dumb python25 package generated by our IT department where provides tag is incorrect. How do I remove automatically added dependencies from generated RPM?

  Read the article

• Why Does My iMac Keep Setting the Screen Brightness to 'Full'?

  - by TomB

  I have a 2 week old 24" iMac running Mac OS X 10.6. It is the primary monitor with the menu bar on the top of display. I have an external monitor as well, a 19" Viewsonic LCD. The LCD is set to the left side of the iMac, rotated 90 degrees CCW and has the Dock along the far left edge. When I restart the screen brightness on the iMac reverts to Full brightness. The Viewsonic LCD retains the setting I have for it. I am using a Mini DVI to DVI cable for the external display. I even tried setting my Huey Pro to do automatic screen adjustment based on ambient lighting but the iMac still goes to stun with a reboot. I am sure it is something dumb I have overlooked.

  Read the article

• Small, fast shopping cart setup

  - by R..

  I'm looking for an open source shopping cart solution that's simple and easy to setup. The requirements are: Quick setup for someone familiar with *nix webservers. Checkout via PayPal (other payment methods not needed). Customers should not have to create an account to make a purchase. At least a minimal level of inventory control. Ability to print/export a list of orders in compact form. Any recommendations for something I should try? Ability to get it up and working quickly is really my priority right now; if it's not ideal, it can be replaced (or, as I'm looking for open source, I can adapt it to fit the requirements better) at a later time. Edit: Really what I'm looking for is simplicity. This will be for a small local business, and the orders will consist of 1-10 items that are being delivered by a driver who needs a simple list of what each customer received when making delivery. Looking like a giant online computer/electronics/etc. store is definitely not a desirable quality. The simpler the interface presented to customers (who are used to purchasing through dumb web forms and paying COD), the better.

  Read the article

• Why is an anemic domain model considered bad in C#/OOP, but very important in F#/FP?

  - by Danny Tuppeny

  In a blog post on F# for fun and profit, it says: In a functional design, it is very important to separate behavior from data. The data types are simple and "dumb". And then separately, you have a number of functions that act on those data types. This is the exact opposite of an object-oriented design, where behavior and data are meant to be combined. After all, that's exactly what a class is. In a truly object-oriented design in fact, you should have nothing but behavior -- the data is private and can only be accessed via methods. In fact, in OOD, not having enough behavior around a data type is considered a Bad Thing, and even has a name: the "anemic domain model". Given that in C# we seem to keep borrowing from F#, and trying to write more functional-style code; how come we're not borrowing the idea of separating data/behavior, and even consider it bad? Is it simply that the definition doesn't with with OOP, or is there a concrete reason that it's bad in C# that for some reason doesn't apply in F# (and in fact, is reversed)? (Note: I'm specifically interested in the differences in C#/F# that could change the opinion of what is good/bad, rather than individuals that may disagree with either opinion in the blog post).

  Read the article

• mdadm: brakes boot due to "is not ready yet or not present" error

  - by BarsMonster

  This is so damn frustrating :-| I've spent like 20 hours on this nice error, and seems like dozens of people over Internet too, and no clear solution yet. I have non-system RAID-5 of 5 disks, and it's fine. But during boot up it says that "/dev/md0 is not ready yet or not present" and asks to press 'S'. Very nice for Ubuntu Server - I have to bring monitor and keyboard to go next. After this system boots and it's all fine. md0 device works, /proc/mdstat is fine. When I do mount -a - it mounts this array without errors and works fine. As a dumb and shameful workaround I added noauto in /etc/fstab, and did mounting in /etc/rc.local - it works fine then. Any hints how to make it work properly? fstab: UUID=3588dfed-47ae-4c32-9855-2d69df713b86 /var/bigfatdisk ext4 noauto,noatime,data=writeback,barrier=0,nobh,commit=5 0 0 mdadm config: It is autogenerated: # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR CENSORED # definitions of existing MD arrays ARRAY /dev/md/0 metadata=1.2 bitmap=/var/md0_intent UUID=efccbeb6:a0a65cd6:470dcdf3:62781188 name=LBox2:0 # This file was auto-generated on Mon, 10 Jan 2011 04:06:55 +0200 # by mkconf 3.1.2-2

  Read the article

• Why do partially failed/failing switches fail to pass DHCP?

  - by David Mackintosh

  I've noticed this several times: a switch starts to behave oddly. Usually if the switch doesn't fail outright, what tends to get noticed is that DHCP doesn't work. We had a Linksys SRW-224P fail today. Systems which were still connected worked properly, until it came time to renew their DHCP lease. Once the lease expired, they stopped working, but up until then we couldn't detect a failure. This includes PoE VoIP phones -- they work fine until their lease is up, at which point they're done. I've noticed this on the above-mentioned Linksys, three varieties of 3Com, and possibly half a dozen dumb switches. What is it about DHCP that makes it sensitive to failing switches?

  Read the article

• Difficulty Mounting Volumes on a Partitioned External HD

  - by Todd

  I'm having a great deal of difficulty with an external hard drive. I'm currently running a dual boot system (XP Service Pack 3 and Ubuntu 11.04 Natty Narwahl) on a Dell Inspiron B120. I'm trying to set up a new 80 GB Hitachi external HD. Using GParted, I formatted the drive and set up the partitions. The partitioning scheme is as follows 10GB NTFS Primary, 2GB Linux-Swap Primary, 50GB FAT32 Primary, 12GB Unallocated. After applying those changes, I went into Disk Utility and the HD appears along with the correct partitions. When I try to mount the volumes for partitions 1 and 3, I get a pop-up stating: Error Mounting Volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. When I try to to check the filesystem I get a pop-up stating: Error Checking filesystem on volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. Throughout the time that I'm attempting to troubleshoot the problem, the external drive light is on and blinking. With my frustration hitting a boiling point, I try to shut down the drive and remove it so that I can plug in a different external HD that works PERFECTLY. However, when I try to shut down and safely remove the drive, I get a pop-up stating: Error Detaching Drive An error occurred while performing an operation on "80GB Hard Disk" (HTS548080m9AT00): The daemon is being inhibited. Can anyone tell me what I'm doing wrong? I'm a newbie and not that skilled with terminal commands, so please dumb it down for me if you request specific command output.

  Read the article

• "The daemon is being inhibited" error message when mounting volumes on a partitioned external HD [closed]

  - by Todd

  I'm having a great deal of difficulty with an external hard drive. I'm currently running a dual boot system (XP Service Pack 3 and Ubuntu 11.04 Natty Narwahl) on a Dell Inspiron B120. I'm trying to set up a new 80 GB Hitachi external HD. Using GParted, I formatted the drive and set up the partitions. The partitioning scheme is as follows 10GB NTFS Primary, 2GB Linux-Swap Primary, 50GB FAT32 Primary, 12GB Unallocated. After applying those changes, I went into Disk Utility and the HD appears along with the correct partitions. When I try to mount the volumes for partitions 1 and 3, I get a pop-up stating: Error Mounting Volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. When I try to to check the filesystem I get a pop-up stating: Error Checking filesystem on volume An error occurred while performing an operation on "Home" (Partition 3 of HTS548080m9AT00): The daemon is being inhibited. Throughout the time that I'm attempting to troubleshoot the problem, the external drive light is on and blinking. With my frustration hitting a boiling point, I try to shut down the drive and remove it so that I can plug in a different external HD that works PERFECTLY. However, when I try to shut down and safely remove the drive, I get a pop-up stating: Error Detaching Drive An error occurred while performing an operation on "80GB Hard Disk" (HTS548080m9AT00): The daemon is being inhibited. Can anyone tell me what I'm doing wrong? I'm a newbie and not that skilled with terminal commands, so please dumb it down for me if you request specific command output.

  Read the article

• Restrict Overriding memory_limit in php.ini

  - by Rohit Batra

  We have a issue that just came to our notice, some of our developers used ini_set('memory_limit', -1) to over-ride the php.ini memory_limit settings in their code files. Due to which sometimes our Memory/CPU usage is way far more than usual and we even have experienced server hanging/crashing many times. Is there any way to restrict these changes for certain params like memory_limit, upload_max_filesize & post_max_size? Users should not be able to edit them after a certain limit set? Sorry if i asked a dumb question, tried searching but there was no reference to this only found answers asking for increasing these parameters.

  Read the article

• LAMP: How do I set up http://myservername.com/~user access?

  - by Travesty3

  Been trying to Google this, but I can't figure out good search terms to find any info about what I need, since I don't really know what it's called. I'm pretty much being thrown to the wolves to figure out how to set up a LAMP server. We had someone who knew how to do it, he set one up and then quit. It was set up so that when I went to "http://{myservername}.com/~travis" it showed the contents of my /home/travis/public_html folder. This worked fine, then we lost power and the server restarted (I know, battery backup, but this is a dev server in a dev building so it's OK). Now, the browser can't find that URL. I also need to know how to set this up on a new server, so instead of wasting time diagnosing this problem (probably just something dumb I did messing with settings or something), I really need to know how to set this up from scratch. Thanks for taking the time to read this and (hopefully) answer!

  Read the article

• How to detect device type from device connected to router?

  - by molly

  I have a att router and there is an unknown device connected to my network. I can't seem to kick it off because of how att's router settings are created which is kind of dumb. I am able to see its local ip and mac address. I am on a mac with snow leopard. How can I get more information on the device with the information that I have? I want to see what kind of device it is, I have checked all devices that are connected to the router and none seem to match the local ip that is connected. I have WPA encryption setup with a strong password.

  Read the article

• Is StackOverflow making me stupid? [closed]

  - by Ayush Goyal

  Possible Duplicate: When stuck, how quickly should one resort to Stack Overflow? Its good that solution to almost every programming problem is available at my disposal, either someone has asked it before or programming gurus are waiting for me to post it..sometimes its just the matter of seconds after posting the question and someone points out the error-causing-line or proposes alternate (easier, lightweight and efficient) solution. But today it struck me "is this making me dumb?" In good (umm..not so good) old days I used to figure out the source of my problem and then work it out myself, though it used to eat up lot of time but it helped in developing my logical thinking as it used to make an impression in my mind due to which I tend to avoid that situation in future codes. Now, as soon as I encounter a problem I just give it a shot or two and head towards the community. Many times after looking at the solution it turns out that answer was all in front of me..all I needed was to take a break, hover it once and its solved. Both the approaches make me feel guilty, for wasting time when I could have asked and solved it within minutes OR being too lazy to look over it again before posting the code snippet.

  Read the article

• Why isn't this smbmount attempt working?

  - by Max Williams

  I can successfully access one of our local samba shares, which is on a windows pc (called marina) as follows: $ sudo /usr/bin/smbclient \\\\marina\\resource_library <my password> Domain=[MARINA] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] smb: \> So, that works. I'm now trying to mount the above location (the resource_library folder on marina) to /mnt/resource_library (as a read only folder), but it keeps failing - i've tried a few variations of specifying the location: $ sudo smbmount \\\\marina\\resource_library /mnt/resource_library -o username=max,password=<my password>,r mount error: could not resolve address for marina: No address associated with hostname No ip address specified and hostname not found and $ sudo smbmount //marina/resource_library /mnt/resource_library -o username=max,password=<my password>,r mount error: could not resolve address for marina: No address associated with hostname No ip address specified and hostname not found and both of the above with MARINA instead of marina. It's bound to be some dumb mistake i'm making, can anyone see it? cheers, max

  Read the article

• how to detect device type from connected device to router?

  - by molly

  i have a att router and there is an unknown device connected to my network. i cant seem to kick it off because of how att's router settings are created which is kind of dumb. i am able to see its local ip and mac address. i am on a mac with snow leopard. how can i get more information on the device with the information that i have? i want to see what kind of device it is, i have checked all deviced that are connected to the router and non seem to match the local ip that is connected. i have wpa encryption setup with a strong password.

  Read the article

• Google search question, front page not showing

  - by user5746

  I know this is probably a dumb question but I hope someone can give me some insight; I was ranked on Google first page of search results for "funny st patricks day shirts" but I was third from the bottom and not familiar enough with SEO, so I signed up for "Attracta" to rank higher. Big mistake. Since using Attracta, I've lost the first page and I'm now on the fourth page in that search. What I noticed is that Google is now just showing a sub-page or side page, (a link from my front page, to a page which has only a few designs in it) this is not where I would want customers to land first... but my front page is not showing in that search anymore. Obviously, the title of this side page is not geared toward that search result, so I know that's why I have the pr drop. Why is my front page not ranking over that page, though? Why is it apparently gone from that search, or so far back no one will ever find it? I need to know how to fix this quick if anyone has any advice at all for me. It's the busiest season for my website and the people who were stealing design ideas from me are all ranked higher than my site now. (I can prove this, lol) So, I'm very frustrated by that. I would be very grateful to have any advice at all as to what I can do to fix this. THANKS in advance for any advice you can offer. Catelyn

  Read the article

• Time tracking similar to Paymo Plus on Debian

  - by aditya menon

  PaymoPlus is free (closed source but no fees) PaymoPlus sits in my System Tray all day, and records every window/tab I open I would like to know if a similar app exists for Debian. Paymo for Windows/Mac has the additional sweet feature of being able to drag and drop working windows/tabs and the time spent into the tasks, but one can live without this. I would at least need to know which tasks got how much time in a 'sum total' calculation so I can enter that time into my Paymo reporting. Any ideas? Paymo does have a desktop widget for Linux but it is a dumb (non-sentient) manual time entry tool, not like Paymo Plus automatically recording everything being done.

  Read the article

• compressing dd backup on the fly

  - by Phil

  Maybe this will sound like dumb question but the way i'm trying to do it doesn't work. I'm on livecd, drive is unmounted, etc. When i do backup this way sudo dd if=/dev/sda2 of=/media/disk/sda2-backup-10august09.ext3 bs=64k ...normally it would work but i don't have enough space on external hd i'm copying to (it ALMOST fits into it). So I wanted to compress this way sudo dd if=/dev/sda2 | gzip > /media/disk/sda2-backup-10august09.gz ...but i got permissions denied. I don't understand.

  Read the article

• iTunes memory usage

  - by Jordan S. Jones

  Why does iTunes use upwards of 70 megs of ram when it is minimized to my system tray playing music? -- Update -- I understand that iTunes is a resource hog :) What I'm trying to find out, is what part of iTunes is using all that ram. Is it the music library? If I have a smaller music library, will it use less ram? Is it loading all the Album Artwork into ram for some dumb reason? Additionally, is there any recommendations on what someone could do to reduce the amount of ram it is using?

  Read the article

• Can I create a virtual network interface to connect to a real network device?

  - by michelemarcon

  I have a networked windows pc with 2 network interfaces. The first connects to a lan with ip address 10.1.. The second connects to another lan with ip address 10.2.. Maybe it's a dumb question, however is it possible to virtualize the second network interface, so that the pc can connect to the 2 lans? If necessary, I may switch to linux or paravirtualization. CLARIFICATION: I want to send DHCP broadcast packets on the second lan, but not on the first lan. I want to do it with one single physical network interface. At the moment, I'm not using any virtualization software.

  Read the article

• Acer S3 SSD and HD Deleted partitions?

  - by user207784

  I'm new to Linux and Ubuntu, and I think I have a problem. I have an Acer Aspire S3 with 20GB SSD and 320GB HD. I installed Ubuntu 12.04 64bit on it today, and when it asked about partitions, without knowing better, I erased the partitions. There is some information at https://help.ubuntu.com/community/AspireS3 about using the SSD and HD efficiently, but since I deleted the partitions, I don't know what to do. How can I recreate the partitions mentioned in the above link so that I can take advantage of having SSD and HD? I installed GParted, but I don't know what I should do now, and I don't want to screw things up further. I greatly appreciate any help that can be offered me. EDIT: I was playing with GParted, and I just realized that I can see dev/sda and dev/sdb, so perhaps I didn't do something horrible to my partitions. I am also sorry for asking such (dumb?) questions. At this point, is there a way to tell whether I have actually screwed up my partitions? Thanks, Joe

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >