Search Results

Search found 1323 results on 53 pages for 'onboard vga'.

Page 9/53 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• Cannot establish maximum resolution on ASUS PB278Q

  - by dentuzhik

  I've recently bought brand new ASUS PB278Q monitor. When trying to connect to my laptop, everything works great, except that I can't get the native resolution of my monitor (2560x1440) working. The automatic is 1920x1080. My graphic card is Nvidia GeForce 320m. Here's output from lspci for it: ~$ lspci | grep VGA 02:00.0 VGA compatible controller: NVIDIA Corporation GT216M [GeForce GT 320M] (rev a2) and also xrandr: ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected primary 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 I have proprietary drivers installed on my machine, here's the info about the monitor from nvidia-settings (Actually I don't have enough reputation to post images, so here's the text): Chip Location: Internal Signal: TDMS Connection link: Single Native resolution: 2560x1440 Refresh rate: 60.00 Hz The monitor is connected to laptop via HDMI cable, and honestly I have no idea what version it is, and what version is my HDMI output of my graphics card. I tried to find how I can figure it out on the web, but had no luck. Also my video card has only VGA and HDMI outs so I can't test neither DVI-D cable nor DisplayPort. So apparently, there's some problem over there. At least I want to know exactly what's going on. I've tried to see if it a linux-specific problem, but windows also gave me the same resolution by default. What I've already tried: Connect through VGA (stupid one, of course it gave me 1920x1080). Checked two HDMI cables (not sure if they're the same or not, as mentioned above). Played around with xrandr and adding custom modes. Didn't help. Surfed for the info a lot on the web, but couldn't get appropriate results. Actually xrandr gives me the following: ~$ cvt 2560 1440 60 # 2560x1440 59.96 Hz (CVT 3.69M9) hsync: 89.52 kHz; pclk: 312.25 MHz Modeline "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr --newmode "2560x1440_60.00" 312.25 2560 2752 3024 3488 1440 1443 1448 1493 -hsync +vsync ~$ xrandr Screen 0: minimum 8 x 8, current 3286 x 1437, maximum 8192 x 8192 VGA-0 disconnected (normal left inverted right x axis y axis) LVDS-0 connected 1366x768+0+669 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ HDMI-0 connected primary 1920x1080+1366+0 (normal left inverted right x axis y axis) 600mm x 340mm 1920x1080 60.0*+ 59.9 50.0 30.0 25.0 24.0 60.0 50.0 1680x1050 60.0 1440x900 59.9 1280x1024 75.0 60.0 1280x960 60.0 1280x800 59.8 1280x720 60.0 59.9 50.0 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 720x576 50.0 720x480 59.9 640x480 75.0 59.9 59.9 480x576 50.0 480x480 59.9 2560x1440_60.00 (0x34f) 312.2MHz h: width 2560 start 2752 end 3024 total 3488 skew 0 clock 89.5KHz v: height 1440 start 1443 end 1448 total 1493 clock 60.0Hz ~$ xrandr --addmode HDMI-0 2560x1440_60.00 X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 What I intend to do next: Try another HDMI cable? Try HDMI to DVI-D cable? Try HDMI to DisplayPort cable? Another type of adapters? VGA to DVI-D? Buy another laptop with another graphic card. Damn. My ideas pretty much end here. Any ideas? Any explanations why it isn't working are appreciated.

  Read the article

• How do I resolve certificate errors on HP blade center

  - by Martin Hilton

  I'm trying to sort out the ssl certificate errors that we get when trying to manage our HP c7000 blade enclosures. To that end I have created a signing certificate and imported it into the browser. In Onboard Administrator I created a certificate signing request, which I signed with my CA and then uploaded the certificate. This worked perfectly, and I no longer get any SSL errors when connection to Onboard Administrator. The problem comes when trying to connect through Onboard Administrator to the iLo on the blades themselves. Done by clicking on the "Web Administration" link. Onboard Administrator links to the blade with it's IP address rather than host name. But the certificate signing request that iLo creates uses the host name. Even when this certificate is signed the browser still complains it is for the wrong domain. I either need to be able to get Onboard Administrator to connect to the blades using host name rather than IP address, or get a certificate signing request which contains the IP address as the CN rather than the host name. It doesn't particularly matter which. Does anybody know how to configure this?

  Read the article

• Intel graphic chipset and NVIDIA Geforce GTX560

  - by antoine

  I have an NVIDIA Geforce GTX560 with two video projectors and I would like to use the onboard Intel Graphic Chipset to plug an additional monitor. I saw the question : How can I use both Intel onboard and Nvidia graphics at the same time? but the answer is so short that I was not convinced. My motherboard (GIGABYTE GA-H61M-D2P-B3 (rev. 1.0)) equipped with Intel H61 Chipset allow shared memory between onboard and PCIe cards. And Windows 7 allow me to use the three outputs thanks to Intel's driver. I'm able to use the onboard graphic card but without graphical interface for now. I think i need intel driver for that. But I would like to know if I can setup my displays in xorg.conf with something like : Section "Device" Identifier "Device0" Driver "intel" EndSection Section "Device" Identifier "Device1" Driver "nvidia" EndSection Section "Device" Identifier "Device2" Driver "nvidia" EndSection Does anyone have successfully setup something like that ? Or should I burn my head experimenting it by myself ? Or is there any good reasons to discouraged me to try ? Thanks for your help. Antoine PS : i'm using Ubuntu 10.10 for now, but I could switch to another version. PS2 : i also read this : Use 3 monitors w/built-in intel adapter + two old nvidia PCI cards on 10.10? which doesn't tell me more about the possibilities to use Intel Graphic and Nvidia at the same time EDIT : according to that : Can not get Dual Monitors to work on Different GPUs, I should be able to run two Xserver one on Intel the other on Nvidia. I will try and post the result here.

  Read the article

• ATI Radeon 5670 Won't Show Resolutions over 1400x900

  - by Phil Sandler

  Just got my new Dell computer with Windows 7 and an ATI Radeon 5670. I attached it to my current monitor, which is a Samsung 24" (2443bwt). Windows 7 does not allow me to display in resolutions greater than 1400 x 900. The setup through a VGA cable into the VGA port of the card. The card also has a DVI port, but I need to use the VGA port because a KVM that supports VGA only. My old PC (which is Windows XP, GeForce 8600 video) can display in 1900 x 1200 on the same monitor (which is what I want) and even higher. It does this through a vga cable also connected to the KVM (through the DVI port but using an adapter). I have tried the same setup (DVI = VGA adapter) on the new PC and nothing changed. I have tried: Updating the drivers via Windows "Update Driver" (says they are current) Installing the updated version of the drivers from ATI (made no difference) Installing Powerstrip (all the options I would need for a custom resolution are greyed out) Installing the drivers/software from ATI caused the ATI Catalyst Control Center software to stop functioning, so I can no longer even start it. I have found some references to other people having this problem and instructions on cleaning the software off and reinstalling it (as uninstalling normally doesn't solve it). I will try this tonight. In any case, I didn't see any options in CCC that would allow me to override the settings for max resolution. However I didn't tinker with it too much before I tried updating the drivers, so I may have missed a setting. I contacted Samsung via online chat and they say it's a problem with the video card/driver (of course--what else would they say?). Any thoughts on what else I could try?

  Read the article

• How to switch 'default' sound device controlled by hardware keys in Xubuntu?

  - by Ruth

  I installed xubuntu-desktop on a 12.04 Ubuntu upgrade after finding Gnome3 lacking. I've mostly been happy, but I've found an odd and frustrating bug. My laptop has two sound 'outputs' - an HDMI-out plug I never use, and the onboard speakers/headphones. For some reason, the hardware keys have been mapped to the HDMI output, even if I set it as 'fallback' in pavucontrol, and notify-osd only displays changes in the HDMI output (though the panel indicator volume control controls onboard sound). I'd ideally like both hardware keys and notify-osd to be looking at the onboard sound, though if I can't get notify-osd it's an acceptable loss. Having to click through a bunch of stuff to change volume is driving me crazy, though. Googling suggested that it /may/ be a Pulseaudio/ALSA conflict, but the hardware keys seem to change at least indicated volume in pavucontrol for HDMI as expected (I don't have an HDMI cable to test actual sound output)

  Read the article

• Tools for Enterprise Architects: OmniGraffle for iPad?

  - by pat.shepherd

  Well, I have to admit to being a bit of an Apple fan and, of course, and early adopter of gadgets and technology in general.  So, when FedEx showed up with my iPad 3G last week, I was a kid in a candy store.  One of the apps that my “buy finger” was hovering over for a while (like all of 3 days) was Omnigraffle for the iPad.  I imagined that it would be very cool to use this with a customer’s EA’s to sketch out Business, Application, Information and Technology architectures.  Instead of using the blackboard, this seemed to offer promise as a white-boarding tool with obvious benefits over a traditional white-board.  I figured I’d get a VGA adapter, plug it into the customer’s projector and off we would go with a great JAD tool.  The touch pad approach offered an additional hands-on kind of feel. So, I made the $49.99 purchase + the $29.99 VGA adapter and tried to give it a go.  Well, I was both pleasantly and unpleasantly surprised.  It is both powerful and easy to use.  There are great stencils included for shapes, software icons, Visio shapes, and even UML notation.  There is even a free-hand tool that works well.  I created some diagrams pretty quickly.   The one below was just a test and took all of 10 minuets to do. The only problem was that Onmigraffle does not recognize the VGA output, so I was stopped dead in my tracks, as it were.  My use case was as a collaborative diagramming tool with other architects, though I can still use it off line.  I called Omnigraffle and they said that VGA support is on the feature request list so, hopefully, in a short amount of time, I can use the tool as I envisioned.   Review: Criteria Result Is it fun? Yes Is it Useful? Yes Does it Show Promise? Yes Did the VGA Output Work? No File/diagram Formats PDF, Onmigraffle proprietary, image   Quick Sample:     OmniGraffle for iPad - Products - The Omni Group

  Read the article

• Enable compiz on Ubuntu with SiS 771/671

  - by Daziplqa

  I have the following Graphics card info: >lspci | grep VGA 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter (rev 10) And I need to enable compiz, even with less moves :), How can I?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the last Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the latest Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• No virtual console on ubuntu 12.10

  - by Buzzzz

  When I try to do a ctr-alt f(1-6) in ubuntu 12.10 I only get a black screen with a blinking cursor but no login prompt. Any ideas on what could be wrong? It is a fresh install of 12.10 using a amd radeon 5850 graphics card. i have tried different things in my /etc/default/grub but at the moment I use the following: # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. # For full documentation of the options in this file, see: # info -f grub -n 'Simple configuration' GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=10 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash vga=normal" #GRUB_CMDLINE_LINUX="vga=0x0376" #RUB_CMDLINE_LINUX_DEFAULT="vga=0x014c" #GRUB_CMDLINE_LINUX="vga=0x014c" #GRUB_GFXPAYLOAD_LINUX=1600x1200x24 # Uncomment to enable BadRAM filtering, modify to suit your needs # This works with Linux (no patch required) and with any kernel that obtains # the memory map information from GRUB (GNU Mach, kernel of FreeBSD ...) #GRUB_BADRAM="0x01234567,0xfefefefe,0x89abcdef,0xefefefef" # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console

  Read the article

• Graphic Setup tune-up checklist

  - by Click Ok

  I was trying to play the game Warzone 2100 and the games runs fine, with nice speed, but the screen stays with a horizontal lines "flickering"... My PC have a integrated GeForce Go 6100 vga. Ok, not a powerfull vga, but it's not the end of the world to run a "simple" game like this (compared with another games that ask you send your eyes to purchase a expensive vga). So, I think that the problem can be of the configuration of my machine. I use it in first instance for programming jobs, so I underpay attention to video setup. I would like about a checklist to know if my PC is "ready" to games. By example, I know that I need: Lastest vga drivers Updated DirectX and OpenGL What you suggest? There is too some good programs to test performance and suggests improvements in the system? Thank you! PS: I'm using Windows 7

  Read the article

• Disappeared graphics card

  - by lenovo user

  I have a Lenovo T520 with two graphics cards, an nVidia quadro and an intel graphics card. I'm running a Ubuntu and Windows 7 dual boot. I can no longer find any trace of my intel graphics card. In my linux boot: > lspci | grep VGA > 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) In Windows in control panel display- advanced settings, I only see the NVIDIA Quadro 2000M. In the BIOS there is no mention of the intel graphics card, no where I can find to try and turn it on or off. I thought I was going crazy, but then I found a post I made on ask ubuntu I made 3 months ago where I listed the output of lspci on this same machine: lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) What is going on? How could my intel graphics card have been disabled or turned off somehow without my knowledge? I've been in the BIOS 3 times now, each time convinced the last time I must have missed something, but I always find nothing. Am I missing something there? Could a thief have opened my computer and stolen my graphics card?

  Read the article

• How to turn off ATI adapter on Acer Timeline 4810G with ubuntu 9.10

  - by netimen

  I can't turn off my ATI adapter. I have applied the fix, but still lspci | grep VGA gives 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] (rev ff) and my power consumption is about 15W (Wi-Fi on). I run ubuntu 9.10, kernel 2.6.31-14-generic. BIOS version 2.30

  Read the article

• Ubuntu openGL issues

  - by Dank101

  my OpenGL doesn't work at all i get Xlib: extension "GLX" missing on display ":0". lspci output 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) (prog-if 00 [VGA controller]) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:1246] (rev a1) (prog-if 00 [VGA controller]) dmesg | grep -i nvid [ 9.469068] nvidia: module license 'NVIDIA' taints kernel. [ 9.538786] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.538792] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.538796] nvidia 0000:01:00.0: enabling device (0006 -> 0007) [ 9.538803] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.538809] nvidia 0000:01:00.0: setting latency timer to 64 [ 9.538942] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.48 Sun Sep 9 [10300.955799] nvidia 0000:01:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b) [10300.955803] nvidia 0000:01:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfff80000) [10300.955807] nvidia 0000:01:00.0: restoring config space at offset 0x9 (was 0x1, writing 0x4001) [10300.955811] nvidia 0000:01:00.0: restoring config space at offset 0x7 (was 0xc, writing 0xd000000c) [10300.955814] nvidia 0000:01:00.0: restoring config space at offset 0x5 (was 0xc, writing 0xc000000c) [10300.955817] nvidia 0000:01:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xf0000000) [10300.955820] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800000, writing 0x10) [10300.955823] nvidia 0000:01:00.0: restoring config space at offset 0x1 (was 0x100006, writing 0x100007) my computer is a dell XPS l702x

  Read the article

• Problem with installing Nvidia display drivers on Ubuntu 13.10

  - by Pascal

  Hello everyone and thank you for taking a look at this topic! I'm currently trying out Ubuntu 13.10 but I keep hitting a wall when it comes to installing a driver. I've tried: sudo apt-get install nvidia-current This resulted in a un-bootable system. The screen just stayed black and the cursor displayed as an 'X'. After that I did had to re-install Ubuntu. The computer I'm using is an Acer-Aspire-V3 with a build in Nvidia geforce GT 630M and also with a Intel HD graphics chip-set (not sure if chip-set is the right word here). "lspci | grep VGA" output: pascal@pascal-Aspire-V3-571G:~$ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 630M] (rev a1) I've searched a bit here and there and found out that it would be wise to mention that this laptop is using (or so I think) Nvidia Optimus, not sure if it will add anything to the subject but at least I'll mention it just to be sure. Now to the questions: Q1 How is this caused and how can I fix it? Q2 What additional information could I provide to help you help me?

  Read the article

• HDMI video connection cuts top and bottom borders of screen

  - by Luis Alvarado

  Ok this is an extension of another problem I had with a VGA connection and an Nvidia Geforce GT 440 card. Here is goes the explanation of this particular problem: I have a Soneview 32' TV. This TV has many connections including VGA (First reason I bought it), HDMI (Second reason but did not have a HDMI cable at that time) and DVI. I have had this TV for little over a month now, actually I had it to celebrate the release of Ubuntu 11.10 and started using it exactly on that date (I know too much fan there but hey, I like geek stuff). I started using it with the VGA cable. After 2 weeks I bought an Nvidia GT440 card. The previous 9500GT was working correctly with no problems whatsoever. I installed the GT440 and the first problem that I encountered using this latest card is mentioned here: Nvidia GT 440 black screen problem when loading lightdm greeter. The solution to this problem was to actually disconnect then connect again the VGA cable. This would result in the screen showing me the lightdm screen for my login. If I did not disconnect then connect the cable I could be there forever thinking that there is no video signal. I got tired of looking for answers that did not work and for solutions that made me literally have to install Ubuntu again. I just went and bought a HDMI cable and changed the VGA one for that one. It worked and I did not have to disconnect/connect the cable but now I have this problem when using any resolution. My normal resolution is 1920x1080 (This TV is 1080HD) so in VGA I could use this resolution with no problem, but on HDMI am getting the borders cut out. Here is a pic: As you can see from the PIC, the Launcher icons only show less than 50% of their witdh. Forget about the top and bottom parts, I can access them with the mouse but I can not visualize them in the screen. It is like it's outside of the TVs view. Basically there is like 20 to 30 pixels gone from all sides. I searched around and came to running xrand --verbose to see what it could detect from the TV. I got this: cyrex@cyrex:~$ xrandr --verbose xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 175, current 1920 x 1080, maximum 1920 x 1080 default connected 1920x1080+0+0 (0x164) normal (normal) 0mm x 0mm Identifier: 0x163 Timestamp: 465485 Subpixel: unknown Clones: CRTC: 0 CRTCs: 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: 1920x1080 (0x164) 103.7MHz *current h: width 1920 start 0 end 0 total 1920 skew 0 clock 54.0KHz v: height 1080 start 0 end 0 total 1080 clock 50.0Hz 1920x1080 (0x165) 105.8MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 55.1KHz v: height 1080 start 0 end 0 total 1080 clock 51.0Hz 1920x1080 (0x166) 107.8MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 56.2KHz v: height 1080 start 0 end 0 total 1080 clock 52.0Hz 1920x1080 (0x167) 109.9MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 57.2KHz v: height 1080 start 0 end 0 total 1080 clock 53.0Hz 1920x1080 (0x168) 112.0MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 58.3KHz v: height 1080 start 0 end 0 total 1080 clock 54.0Hz 1920x1080 (0x169) 114.0MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 59.4KHz v: height 1080 start 0 end 0 total 1080 clock 55.0Hz 1680x1050 (0x16a) 98.8MHz h: width 1680 start 0 end 0 total 1680 skew 0 clock 58.8KHz v: height 1050 start 0 end 0 total 1050 clock 56.0Hz 1680x1050 (0x16b) 100.5MHz h: width 1680 start 0 end 0 total 1680 skew 0 clock 59.9KHz v: height 1050 start 0 end 0 total 1050 clock 57.0Hz 1600x1024 (0x16c) 95.0MHz h: width 1600 start 0 end 0 total 1600 skew 0 clock 59.4KHz v: height 1024 start 0 end 0 total 1024 clock 58.0Hz 1440x900 (0x16d) 76.5MHz h: width 1440 start 0 end 0 total 1440 skew 0 clock 53.1KHz v: height 900 start 0 end 0 total 900 clock 59.0Hz 1360x768 (0x171) 65.8MHz h: width 1360 start 0 end 0 total 1360 skew 0 clock 48.4KHz v: height 768 start 0 end 0 total 768 clock 63.0Hz 1360x768 (0x172) 66.8MHz h: width 1360 start 0 end 0 total 1360 skew 0 clock 49.2KHz v: height 768 start 0 end 0 total 768 clock 64.0Hz 1280x1024 (0x173) 85.2MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 66.6KHz v: height 1024 start 0 end 0 total 1024 clock 65.0Hz 1280x960 (0x176) 83.6MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 65.3KHz v: height 960 start 0 end 0 total 960 clock 68.0Hz 1280x960 (0x177) 84.8MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 66.2KHz v: height 960 start 0 end 0 total 960 clock 69.0Hz 1280x720 (0x178) 64.5MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 50.4KHz v: height 720 start 0 end 0 total 720 clock 70.0Hz 1280x720 (0x179) 65.4MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 51.1KHz v: height 720 start 0 end 0 total 720 clock 71.0Hz 1280x720 (0x17a) 66.4MHz h: width 1280 start 0 end 0 total 1280 skew 0 clock 51.8KHz v: height 720 start 0 end 0 total 720 clock 72.0Hz 1152x864 (0x17b) 72.7MHz h: width 1152 start 0 end 0 total 1152 skew 0 clock 63.1KHz v: height 864 start 0 end 0 total 864 clock 73.0Hz 1152x864 (0x17c) 73.7MHz h: width 1152 start 0 end 0 total 1152 skew 0 clock 63.9KHz v: height 864 start 0 end 0 total 864 clock 74.0Hz ....Many Resolutions later... 320x200 (0x1d1) 10.2MHz h: width 320 start 0 end 0 total 320 skew 0 clock 31.8KHz v: height 200 start 0 end 0 total 200 clock 159.0Hz 320x175 (0x1d2) 9.0MHz h: width 320 start 0 end 0 total 320 skew 0 clock 28.0KHz v: height 175 start 0 end 0 total 175 clock 160.0Hz 1920x1080 (0x1dd) 333.8MHz h: width 1920 start 0 end 0 total 1920 skew 0 clock 173.9KHz v: height 1080 start 0 end 0 total 1080 clock 161.0Hz If it helps, the Refresh Rate at 1920x1080 is 60. There is a flickering effect at this resolution using HDMI but not VGA which I imagine is related to the borders cut off issue am asking here. I have also done the following but this will only solve the problem on lower resolutions than 1920x1080 or on others TV (My father has a Sony TV where this problem is also solved): NVIDIA WAY Go to Nvidia-Settings and there will be an option that will have more features if a HDMI cable is connected. In the next pic the option is DFP-1 (CNDLCD) but this name changes depending on what device the PC is connected to: Uncheck Force Full GPU Scaling What this will do for resolutions LOWER than 1920x1080 (At least in my case) is solve the flickering problem and fix the borders cut by the monitor. Save to Xorg.conf file the changes made after changing to a resolution acceptable to your eyes. TV WAY If you TV has OSD Menu and this menu has options for scanning the screen resolution or auto adjusting to it, disable them. Specifically the option about SCAN. If you have an option for AV Mode disable it. Basically disable any option that needs to scan and scale the resolution. Test one by one. In the case of my father's TV this did it. In my case, the Nvidia solved it for lower resolutions. NOTE: In the case this is not solved in the next couple of weeks I will add this as the answer but take into consideration that the issue is still active with 1920x1080 resolutions.

  Read the article

• NIC reordering on RHEL5/CentOS 5

  - by ewwhite

  I have an HP ProLiant DL360 G6 containing two onboard NICs as well as an HP NC375T (NetXen NX3031 chipset) 4-port PCIe card. The system was running with eth0 and eth1 belonging to the onboard NICs and eth2-eth5 on the NetXen card. I recently rebuilt the server and from the kickstart process onward, the NICs were reordered such that the onboard NICs became eth4 and eth5, while the NetXen card took over eth0-eth3. I've had some experiences in the past where I tied NICs to specific interfaces via changes in the ifcfg-ethX config files, but this is the first time I've ever seen an add-in card take over eth0 from the motherboard's interfaces. This impacted my kickstart scripts, so: 1). How can I ensure that the onboard NICs take precedence in the kickstart arrangement. 2). What is the most consistent way to maintain that ordering through repeated reboots, kernel changes (e.g. going from a RHEL mainline kernel to a RHEL MRG realtime kernel), etc. 3). What is the interaction between the /etc/modprobe.conf module/NIC definitions, the /etc/sysconfig/network-scripts/ifcfg-ethX and the /etc/modprobe.d/blacklist functions in this context?

  Read the article

• No alternative drivers appearing on Software Sources and manual install leads to no unity

  - by Gausie

  I just got a new laptop, installed Ubuntu 12.10 and am trying to install proprietary nvidia drivers. Once I understood the change from jockey, I did a fresh install and followed these instructions: http://techhamlet.com/2012/11/install-nvidia-drivers-in-ubuntu-12-10/ But when I do, Unity crashes on startup. My hardware on lspci | grep VGA is as follows 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GK107 [GeForce GT 650M] (rev a1) I've followed a couple of nvidia 12.10 tutorials on Google but none have helped. Can I get any specific advice?

  Read the article

• 12.04 - Connecting Acer X203H monitor to new Dell XPS 15z laptop

  - by Lucy Dixon

  I have installed the latest version of Ubuntu (12.04) on my boyfriend's new Dell XPS 15z laptop. He uses a Microsoft wireless keyboard and mouse, and an Acer X203H monitor with his set-up. No problems with the keyboard or mouse, or with connecting the HP printer, but we just can't get the laptop to talk to the Acer monitor. With his old setup he used a VGA cable to connect machine & monitor. New laptop has no VGA port, but we've bought a VGA to HDMI adaptor to connect to the laptop. Have tried using Fn F2 to change the display from laptop to monitor, but it doesn't see the monitor at all. HELP! Is there a driver I can install from somewhere? Or how can I tell Ubuntu to look for the monitor on another port? Completely in the dark, and about to get in trouble!! Thanks

  Read the article

• Ubuntu 14.04 ATI/Intel Hybrid Graphics DPM

  - by anchit123

  I have a Dell Inspiron 3521 with hybrid ATI/Intel graphics. (AMD Radeon 7670M / Intel HD 4000) using Ubuntu 14.04 with open source drivers for graphics. (xserver-xorg-video-ati) I read that Ubuntu 14.04 with the linux kernel version 3.13 supports auto switching between graphics and dynamic power management. Is it correct? Anyway, if it is true, I dont think that it is working in my system , because fan runs constantly and battery backup is less than 2 hours. lspci | grep -i vga 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Thames [Radeon HD 7500M/7600M Series] (rev ff) What should I do? Is there any hope that this gets fixed in future kernels?

  Read the article

• Better drivers for SiS 650/740 integrated video?

  - by Bart van Heukelom

  I installed Xubuntu 10.10 on an old box today and the graphical performance is horrid. According to lspci, the video card is this: 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 65x/M650/740 PCI/AGP VGA Display Adapter (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 8081 Flags: 66MHz, medium devsel, IRQ 11 BIST result: 00 Memory at f0000000 (32-bit, prefetchable) [size=128M] Memory at e7800000 (32-bit, non-prefetchable) [size=128K] I/O ports at d800 [size=128] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel modules: sisfb Is there a way to make it faster? Alternative drivers? The additional drivers tool shows nothing. I'm specifically interested in improving Java's Java2D rendering speed, because I'll be running a "stat screen" written in that language on it.

  Read the article

• How to config multiple monitor with optimus?

  - by irrational

  I have an Acer Aspire 8951G running 12.04 Pangolin with bumblebee working beautifully. My problem is that when I connect either the VGA port or the HDMI to my projector there is no way I can see to properly set up the resolutions or colours. The default basic display driver sees the projector correctly, but messes up colours and resolutions (on hdmi) and resolutions on VGA. (Its a 1280 X 720 projector) Am I missing some sort of Xorg configuration? nvidia-xconfig does not seem to exist and running optirun nvidia-settings -c :8 opens the settings, but of course only for the one display. I just want a way to set a default config for my projector via VGA or preferably HDMI. Any help would be wonderful.

  Read the article

• Unable to change the launcher icon size

  - by takeshin

  After upgrading to 11.10 I can't change the launcher icon size to smaller. I've tried to change it using ccsm, like described in How can I configure Unity, but the changes take no effects (restarted, tried sudo - still big icons). In the previous version of Ubuntu this solution worked. How can I change the icon size? (BTW, how can I know which Unity (2D vd 3D) I'm running and switch between?). Edit: Looks like I'm using Unity 2D and have some problems with graphics: me@my-laptop ~ $ /usr/lib/nux/unity_support_test -p Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Error: unable to create the OpenGL context Edit 2 me@my-laptop ~ $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 01:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 310M] (rev a2)

  Read the article

• Dual Monitor/Xinerama not working; cannot even detect on-board graphic card

  - by Steven H

  I have Kubuntu 12.04 and two identical VGA monitors. One I plugged via DVI-VGA adapter into the DVI port of my discrete AMD Radeon HD 6670, the other into the VGA port of my on-board graphic card (Radeon HD 6410D). After installing Kubuntu I got a black screen, so I booted with nomodeset and installed AMD's catalyst drivers but only the monitor plugged into the discrete graphic card worked. Using lspci I saw that the on-board graphics was not listed. Then I found in the BIOS settings the options "Surround View" and "Onboard Dual Link DVI" both disabled. After enabling both, the on-board graphics card shows up in lspci but in amdcccle, it only shows as [Uknown display]Uknown adapter. When I try to enable xinerama, I get a black screen after rebooting on both monitors. I tried several options and hints from the web but nothing worked so far. I also reinstalled the AMD drivers several times. What should I do?

  Read the article

• xrander problem with 1900x1080p

  - by Eslam

  i have a problem with xrandr i successfully executed the following : #cvt 1900 1080 #xrandr 1900x1080 170.75 1904 2024 2224 2544 1080 1083 1093 1120 -hsync +vsync but unfortunately the following command : #xrandr --addmode VGA-0 1900x1080 returned the following error : X Error of failed request: BadMatch (invalid parameter attributes) Major opcode of failed request: 153 (RANDR) Minor opcode of failed request: 18 (RRAddOutputMode) Serial number of failed request: 29 Current serial number in output stream: 30 the following command output might help in identifying problem : #glxinfo |grep -i opengl OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce 310M/PCIe/SSE2 OpenGL version string: 3.3.0 NVIDIA 310.14 OpenGL shading language version string: 3.30 NVIDIA via Cg compiler OpenGL extensions: #lspci |grep -i vga 01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 310M] (rev a2) any ideas what's gonna be wrong ?

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >