Search Results

Search found 4157 results on 167 pages for 'zero subnet'.

Page 9/167 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• How to connect devices behind Comcast router/modem with devices behind wireless router

  - by deeperDATA

  I know this is going to seem like a simple solution but I have been unable to find a clear answer through Google. Simple office setup: I have a Comcast modem/router that has 4 hard wired ports. In one of those ports I have a Cisco wireless router which also has 4 of its own ports. What is the method for getting devices behind the modem/router to ping/communicate with devices behind the wireless router? They are all on the same subnet but the IP ranges differ. The router produces 192.168.1.1 by default while the Comcast modem/router produces 10.1.10.1 by default. I think what I'm attempting to do might be considered "extending" the modem/router's network but I'm not sure. Thank you in advance for your assistance.

  Read the article

• why would you create two different subnets on the same physical network?

  - by xirtyllo

  I'm working at a messy location, one of the strange (for me) things is that on the same physical network there are two different subnets. Specifically some computers will have 10.0.0.0/24 and some others will have 172.16.0.0/24. There is only one DHCP server, which gives IPs on the 10.0.0.0/24 range, and there are two internet gateways, one with IP 172.16.0.1 and one with IP 10.0.0.1 . To give an example, I can easily swap one PC from one subnet to the other just by changing its IP and gateway settings. I am trying to imagine why they created the network this way, and which may be the possible advantages and/or drawbacks of having two different subnets on the same physical network. Any thoughts?

  Read the article

• How to calculate CIDR notation from entries in a routing table

  - by febreezey

  I have some entries in a routing table that were created using longest prefix matching, and I have to use those entries to determine the a.b.c.d/x notation (CIDR). This is an example entry: 11001000 00010111 00010. That was calculated from the range 11001000 00010111 00010000 00000000 through 11001000 00010111 00010111 11111111. I know the range is from IP addresses 200.23.16.0 to 200.23.23.255, but getting the /x for the subnet # doesn't make sense to me. Anyone know how to properly go about calculating it?

  Read the article

• rip in RouterSim

  - by Olga Anastasiadou

  I have to design a network given IPs 146.124.0.0/16 and 146.124.10.0/24. My given requirements are : at least 60 more subnets and maximum 1000 hosts per subnet and use of RIP. I have 3 routers (RA1, RA2, RA3) and 3 subnets (Sales, Logistic and Deposit). I gave WAN1 (RA1-RA3): 146.124.10.0/30, WAN2 (RA2-RA3) : 146.124.10.4/30 and WAN3 (RA1-RA2) : 146.124.10.8/30 and Sales : 146.124.0.0/22, Logistic: 146.124.4.0 and Deposit : 146.124.8.0. When I tried to configure RIP protocol, it didn’t work (I use routerSim 6). What am I doing wrong? Can anyone help please????

  Read the article

• Two subnets on one switch with no VLAN and possible problems

  - by casey_miller

  As far as I know in order to use two subnets on one physical cable VLAN's are recommended. However, is it possible to achieve this (i.e: two subnets on one physical network) like 192.168.1.0/24 and 10.0.0.0/8 networks. What kind of problems or hidden rocks this way contains? With VLAN's it's possible to better isolate so users wouldn't easly sniff the other network. But in my environment it's okay if user on one subnet could listen to the traffic on another network. Is it the only problem?

  Read the article

• Multicast in private LAN with different subnets

  - by Gobliins

  after i read Multicast IP Addresses and Multicast accross the subnets I am confused. Configuration: I have two devices in the same network. They may not be in the same Subnet, but always in the same physical network (beyond the same router, switch etc.) I want to communicate across IP multicast either 224.x.x.x or 239.x.x.x may be more fitting because we want it local, not beyond of forward through the router. Can one machine be the receiver and the other machine sender of the same multicast address? and can the receiving machine send an answer to the sending machine?

  Read the article

• IP assignment in a /28 block

  - by mks

  Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

  Read the article

• Why is this static routing not working ?

  - by geeko

  Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

  Read the article

• DHCP for Multiple Subnets

  - by TheD

  So this is the current setup - essentially I would like to get my DHCP server, serving DHCP requests for two seperate subnets. Netgear DG834G acting as a modem connected to a Sonicwall Pro 2040. X0 - LAN - 192.168.1.0/24 X1 - WAN - <WAN-IP> X2 - WLAN - 192.168.10.0/24 At the moment, I have a 2008R2 server with DHCP installed, with an IP address on the 192.168.1.0/24 range handling DHCP fine for this subnet. The Sonicwall is configured correctly - anything connected to the WLAN has Full Allow to anything in the LAN, and vice versa but it will not lease an IP from my Server. I've also added another IP address to the server, so the physical NIC now has two IP's: 192.168.1.2 and 192.168.10.2 with a DHCP scope configured for each. Still no luck! Any ideas? Thanks!

  Read the article

• How does IPv4 Subnetting Work?

  - by Kyle Brandt

  This is a Canonical Question about IPv4 Subnets How does Subnetting Work, and How do you do it by hand or in your head? Can someone explain both conceptually and with several examples? Server Fault gets lots of subnetting homework questions, so we could use an answer to point them to on Server Fault itself. What is classless routing and why is class-based routing obsolete? If I have a network, how do I figure out how to split it up? If I am given a netmask, how do I know what the network Range is for it? Sometimes there is a slash followed by a number, what is that number? Sometimes there is a subnet mask, but also a wildcard mask, they seem like the same thing but they are different? Someone mentioned something about knowing binary for this? What is NAT (Network Address Translation).

  Read the article

• What's required to enable communication between two IP ranges located behind one switch?

  - by Eric3

  Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

  Read the article

• iptables: separate clients from each other

  - by Florian Lagg

  Hello, is there a way to separate clients in a subnet so that they cannot reach each other? The infrastructure currently looks like this: 192.168.0.1/24 Gateway, a CentOS box with iptables. 192.168.0.10-20 Some clients which may reach each other 192.168.0.30 A single client which should not be able to reach the hosts 192.168.0.10-20 should be able to reach the gateway and the internet I don't know if it is possible, maybe you could give me your ideas how it could be done. I cannot influence the machine 192.168.0.30 because it is a virtual machine I want to rent to someone. Thanks.

  Read the article

• What is the network address (x.x.x.0) used for?

  - by Shtééf

  It appears to be common practice to not use the first address in a subnet, that is the IP 192.168.0.0/24, or a more exotic example would be 172.20.20.64/29. The ipcalc tool I frequently use follows the same practice: $ ipcalc -n -b 172.20.20.64/29 Address: 172.20.20.64 Netmask: 255.255.255.248 = 29 Wildcard: 0.0.0.7 => Network: 172.20.20.64/29 HostMin: 172.20.20.65 HostMax: 172.20.20.70 Broadcast: 172.20.20.71 Hosts/Net: 6 Class B, Private Internet But why is that HostMin is not simply 64 in this case? The 64 address is a valid address, right? And whatever the answer, does the same apply to IPv6? Perhaps slightly related: it also appears possible to use a TCP port 0 and an UDP port 0. Are these valid or used anywhere?

  Read the article

• Unable to ping between subnets and out to internet

  - by battlemidget

  My setup is Modem - Linksys router - Laptop with 2 devices (wlan0/eth0) - desktop machine Router is 192.168.1.1 gateway to the internet Laptop wlan0 is 192.168.1.4 with a gw of 192.168.1.1 Laptop eth0 is 192.168.2.254 which acts as a second gateway desktop is 192.168.2.100 On laptop i've setup ip_forward to 1, and have inserted 2 iptables rules -A FORWARD -i eth0 -o wlan0 -j ACCEPT -A FORWARD -i wlan0 -o eth0 -j ACCEPT The laptop can ping outside the network (i,e, yahoo.com) it can not ping 192.168.2.100. The desktop can ping 192.168.2.254 but nothing outside the network or 192.168.1.0 subnet. On laptop ip route show lists: 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.4 127.0.0.0/8 dev lo scope link default via 192.168.1.1 dev wlan0 What am I missing to make my desktop go through the laptop in order to access the router which provides access to the internet? Thanks

  Read the article

• how to communicate in typical router switch router scenario?

  - by Kossel

  I'm learning routing using packet tracer simulation and I think this is a very commun scenario: let's say pc4 is the server... why I can't ping from PC1 to 192.168.2.253 (router1) but I can ping 192.168.2.2 (pc0) aren't they the same subnet? what am I missing or have to do in order to reach pc4? (192.168.100.254) from pc 1 (192.168.1.1) is there something like "default gateway" for router? thanks for advice PS: during the simulation it shows error "The routing table does not have a route to the destination IP address. The router drops the packe (from 192.168.2.253 to 192.168.1.1)"

  Read the article

• Am I supposed to assign the broadcast IP somewhere?

  - by pvieira

  This is a very basic question from a newbie point of view. I have a dedicated server at Hetzner running Windows 2008 R2. I bought a subnet of IP addresses to use in this server. They provided me a given range of IPs, incluind one Ip labeled as "Broadcast". I know how to assign those IPs to the NIC, but should I do something with the Broacast IP, like configure it somewhere on Windows? Or can I just ignore it and I'll be fine? This IP range will be used to host SSL sites.

  Read the article

• How do I recover jegs with zero bytes?

  - by Jill

  I downloaded some wedding photos into my external drive about a month ago. A total of 3 cards were downloaded into 3 different files. The first file lists all of the photos, about 600 images, but they have zero bytes. The other 2 files are fine. I can't recover the compact flash card because I have used it too many times since then. Is there any way to recover the images on my drive?

  Read the article

• How do I recover JPEGs with zero bytes?

  - by Jill

  I downloaded some wedding photos into my external drive about a month ago. A total of 3 cards were downloaded into 3 different files. The first file lists all of the photos, about 600 images, but they have zero bytes. The other 2 files are fine. I can't recover the compact flash card because I have used it too many times since then. Is there any way to recover the images on my drive?

  Read the article

• Set automatic axis limits without defaulting to zero (Excel)

  - by djeidot

  I am build a bar chart in Excel with data values ranging from e.g. 10 to 20. I want the X axis limits to be automatic, but although the right limit (near 20) works correctly, the left limit always defaults to 0. I'd like the left limit to be near 10, instead of zero, without having to have the limit fixed. Is there any way to do this?

  Read the article

• batch script to retrieve zero byte files

  - by help

  Hi How to retrieve zero byte files and copy into a folder using batch script. can someone help me out.

  Read the article

• VS C++ throwing divide by zero exception after a specific check

  - by Dr. Monkey

  In the following C++ code, it should be impossible for ain integer division by zero to occur: // gradedUnits and totalGrades are both of type int if (gradedUnits == 0) { return 0; } else { return totalGrades/gradedUnits; //call stack points to this line } however Visual Studio is popping up this error: Unhandled exception at 0x001712c0 in DSA_asgn1.exe: 0xC0000094: Integer division by zero. And the stack trace points to the line indicated in the code. It seems like VS might just do this with any integer division, without checking whether a divide by zero is possible. Do I need to catch this exception even though the code should never be able to throw it? If so, what's the best way to go about this? This is for an assignment that specifies VS 2005/2008 with C++. I would prefer not to make things more complicated than I need to, but at the same time I like to do things properly where possible.

  Read the article

• Why is address zero used for null pointer?

  - by Joel

  In C (or C++ for that matter), pointers are special if they have the value zero: I am adviced to set pointers to zero after freeing their memory, because it means freeing the pointer again isn't dangerous; when I call malloc it returns a pointer with the value zero if it can't get me memory; I use if (p != 0) all the time to make sure passed pointers are valid etc. But since memory addressing starts at 0, isn't 0 just as a valid address as any other? How can 0 be used for handling null pointers if that is the case? Why isn't a negative number null instead?

  Read the article

• subneting .. is 192.168.0.1/24 different than 192.168.0.1/25

  - by SM

  So i am trying to understand subnetting. I understand that you can take 192.168.0.0/24 domain and break it up in 2 subnets. 192.168.0.0/25 and 192.168.0.128/25 .. so what if i need to create 2 more subnets inside both of those above subnets. What if i need to create 2 subnets, which have 2 more subnets inside them and each of those 2 subnets have 2 hosts. As per my calculation, this would be something like. top 2 subnets: 192.168.0.0/25 and 192.168.0.128/25 subnets of 192.168.0.0/25: 192.168.0.0/26 - 192.168.0.128/26 subnets of 192.168.0.128/25: 192.168.0.128/26 - 192.168.0.192/26 hosts of 192.168.0.0/25: 192.168.0.1/25 - 192.168.0.2/25 hosts of 192.168.0.128/25: 192.168.0.129/25 - 192.168.0.130/25 hosts of 192.168.0.0/26: 192.168.0.1/26 - 192.168.0.2/26 hosts of 192.168.0.128/26: 192.168.0.129/26 - 192.168.0.130/26 hosts of 192.168.0.128/26: 192.168.0.129/26 - 192.168.0.130/26 hosts of 192.168.0.192/26: 192.168.0.193/26 - 192.168.0.194/26 The above doesnt seem right, i am moving down like a tree, however the subnet mask and IPs are being repeated, i am just add 1 to /x and making the ips from there. Can anyone please tell me if this is correct The scenario i am trying to understand is similar to this, however i just want to add hosts on each level as well. http://www.ciscotrick.com/wp-content/uploads/2008/08/the_mathematical_relationship_between_network_block_sizes.jpg

  Read the article

• Separate computers in my apartment can't communicate to each other?

  - by Razor Storm

  In my apartment, the management provides the building with a network connection. I have my computer plugged into the ethernet coming out of the walls, and my friend who also lives in the apartment building has his computer connected to a separate ethernet jack. As far as I know our two computers are not within a LAN, and ipconfig shows that we only have external ip addresses. The problem, then, appears when we attempt make direct communication between our computers. I have some hosting server set up on my machine, and my friend is unable to connect to it via my ip address. Other people who do not live in the apartment can connect fine. Ethernet adapter Local Area Connection: IPv4 Address. . . . . . . . . . . : 204.29.113.41 Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : 204.29.112.1 His ip: 204.29.113.104 Using a fulltunnel vpn doesn't help.

  Read the article

• Basic OpenVPN setup

  - by WalterJ89

  I am attempting to connect 2 win7 (x64+ x32) computers (there will be 4 in total) using OpenVPN. Right now they are on the same network but the intention is to be able to access the client remotely regardless of its location. The Problem I am having is I am unable to ping or tracert between the two computers. They seem to be on different subnets even though I have the mask set to 255.255.255.0. The server ends up as 10.8.0.1 255.255.255.252 and the client 10.8.0.6 255.255.255.252. And a third ends up as 10.8.0.10. I don't know if this a Windows 7 problem or something I have wrong in my config. Its a very simple set up, I'm not connecting two LANs. this is the server config (removed all the extra lines because it was too ugly) port 1194 proto udp dev tun ca keys/ca.crt cert keys/server.crt key keys/server.key # This file should be kept secret dh keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-to-client duplicate-cn keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 6 this is the client config client dev tun proto udp remote thisdomainis.random.com 1194 resolv-retry infinite nobind persist-key persist-tun ca keys/ca.crt cert keys/client.crt key keys/client.key ns-cert-type server comp-lzo verb 6 Is there anything I missed in this? keys are all correct and the vpn's connect fine, its just the subnet or route issue. Thank You

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >