Search Results

Search found 16455 results on 659 pages for 'hosts allow'.

Page 90/659 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• Authenticating Windows 7 against MIT Kerberos 5

  - by tommed

  Hi There, I've been wracking my brains trying to get Windows 7 authenticating against a MIT Kerberos 5 Realm (which is running on an Arch Linux server). I've done the following on the server (aka dc1): Installed and configured a NTP time server Installed and configured DHCP and DNS (setup for the domain tnet.loc) Installed Kerberos from source Setup the database Configured the keytab Setup the ACL file with: *@TNET.LOC * Added a policy for my user and my machine: addpol users addpol admin addpol hosts ank -policy users [email protected] ank -policy admin tom/[email protected] ank -policy hosts host/wdesk3.tnet.loc -pw MYPASSWORDHERE I then did the following to the windows 7 client (aka wdesk3): Made sure the ip address was supplied by my DHCP server and dc1.tnet.loc pings ok Set the internet time server to my linux server (aka dc1.tnet.loc) Used ksetup to configure the realm: ksetup /SetRealm TNET.LOC ksetup /AddKdc dc1.tnet.loc ksetip /SetComputerPassword MYPASSWORDHERE ksetip /MapUser * * After some googl-ing I found that DES encryption was disabled by Windows 7 by default and I turned the policy on to support DES encryption over Kerberos Then I rebooted the windows client However after doing all that I still cannot login from my Windows client. :( Looking at the logs on the server; the request looks fine and everything works great, I think the issue is that the response from the KDC is not recognized by the Windows Client and a generic login error appears: "Login Failure: User name or password is invalid". The log file for the server looks like this (I tail'ed this so I know it's happening when the Windows machine attempts the login): Screen-shot: http://dl.dropbox.com/u/577250/email/login_attempt.png If I supply an invalid realm in the login window I get a completely different error message, so I don't think it's a connection problem from the client to the server? But I can't find any error logs on the Windows machine? (anyone know where these are?) If I try: runas /netonly /user:[email protected] cmd.exe everything works (although I don't get anything appear in the server logs, so I'm wondering if it's not touching the server for this??), but if I run: runas /user:[email protected] cmd.exe I get the same authentication error. Any Kerberos Gurus out there who can give me some ideas as to what to try next? pretty please?

  Read the article

• ssh_exchange_identification: Connection closed by remote host

  - by Charlie Epps

  First: $ ssh-keygen -t dsa -P '' -f ~/.ssh/id_dsa $ cat ~/.ssh/id_dsa.pub >> ~/.ssh/authorized_keys Connecting to SSH servers gives this message: $ ssh -vvv localhost OpenSSH_5.3p1, OpenSSL 0.9.8m 25 Feb 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to localhost [127.0.0.1] port 22. debug1: Connection established. debug1: identity file /home/charlie/.ssh/identity type -1 debug1: identity file /home/charlie/.ssh/id_rsa type -1 debug3: Not a RSA1 key file /home/charlie/.ssh/id_dsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/charlie/.ssh/id_dsa type 2 ssh_exchange_identification: Connection closed by remote host My /etc/hosts.allow is as following: sshd: ALLOW /etc/hosts.deny is as following: ALL: ALL: DENY I have changed my /etc/ssh/sshd_conf as following: ListenAddress 0.0.0.0 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys PasswordAuthentication no

  Read the article

• SCVMM 2008 R2 problems migrating VM from VS2005 to Hyper-V host

  - by Scott Ivey

  I have System Center Virtual Machine Manager 2008 R2 installed, and have a Hyper-V R2 host and a Virtual Server 2005 host. I'm trying to migrate my machines from the VS2005 host to the Hyper-V host, and keep getting the following error... VMM is unable to complete the requested file transfer. The connection to the HTTP server myserver.mydomain.local could not be established. (Unknown error (0x80072efd)) Recommended Action Ensure that the HTTP service and/or the agent on the machine myserver.mydomain.local are installed and running and that a firewall is not blocking HTTPS traffic. (Note - migrations between Hyper-V hosts managed by the VMM server work fine - my problem is just going from VS2005-Hyper-V hosts) I have no firewalls turned on on either of the servers, and no firewalls in the middle. I've looked all over for answers to this problem, and am getting nowhere. All the articles I find when searching are talking about either V2V or P2V - and i'm just trying to do a straight migrate VM. I've tried rebooting the boxes, changing the BITS SSL port number, restarting services, triple-checking firewalls, etc. Does anyone have any good suggestions as to how I can resolve this problem?

  Read the article

• mod_rewrite: redirect from subdomain to main domain

  - by Bald

  I have two domains - domain.com and forum.domain.com that points to the same directory. I'd like redirect all request from forum.domain.com to domain.com (for example: forum.domain.com/foo to domain.com/forum/foo) without changing address in addres bar (hidden redirect). I wrote something like this and put it into .htaccess file: Options +FollowSymlinks RewriteEngine on RewriteCond %{HTTP_HOST} ^forum\.example\.net$ RewriteRule (.*) http://example.com/forum/$1 [L] RewriteCond %{REQUEST_FILENAME} !-s [NC] RewriteCond %{REQUEST_FILENAME} !-d [NC] RewriteRule ^(.+) index.php/$1 [L] That works only if I add Redirect directive: RewriteRule (.*) http://example.com/forum/$1 [R,L] But it changes previous address in address bar. EDIT: Ok, let's make it simple. I added those two lines at the end of the c:\windows\system32\drivers\etc\hosts on my local computer: 127.0.0.3 foo.net 127.0.0.3 forum.foo.net Now, I created two virtual hosts: <VirtualHost foo.net:80> ServerAdmin [email protected] ServerName foo.net DocumentRoot "C:/usr/src/foo" </VirtualHost> <VirtualHost forum.foo.net:80> ServerAdmin [email protected] ServerName forum.foo.net DocumentRoot "C:/usr/src/foo" </VirtualHost> ..and directory called "foo", where i put two files: .htaccess and index.php. Index.php: <?php echo $_SERVER['PATH_INFO']; ?> .htaccess: Options +FollowSymlinks RewriteEngine on RewriteBase / RewriteCond %{HTTP_HOST} ^forum\.foo\.net$ RewriteCond %{REQUEST_URI} !^/forum/ RewriteCond %{REQUEST_FILENAME} !-s [NC] RewriteCond %{REQUEST_FILENAME} !-d [NC] RewriteRule ^(.+)$ /index.php/forum/$1 [L] RewriteCond %{HTTP_HOST} !^forum\.foo\.net$ RewriteCond %{REQUEST_FILENAME} !-s [NC] RewriteCond %{REQUEST_FILENAME} !-d [NC] RewriteRule ^(.+) index.php/$1 [L] When I type address http://forum.foo.net/test in address bar, it displays /forum/test which is good. http://foo.net/a/b/c shows /a/b/c which is good. But! http://forum.foo.net/ displays empty value (should display /forum).

  Read the article

• Hyper-V virtual machine can't be migrated to a specific host in the cluster

  - by Massimo

  I have a three-node Hyper-V cluster running on Windows Server 2008 R2 which is working quite flawlessly: there are no errors, live migration works, all hosts can and will happily run all virtual machines, and so on. But one specific virtual machinee is trying to make me go mad: it works on two nodes of the cluster, but not on the third one. Whenever I try to move the VM to that node, be it in a live migration or with the VM powered off, it always fails. In the event log of the host these events are logged: Source: Hyper-V-VMMS Event ID: 16300 Cannot load a virtual machine configuration: General access denied error (0x80070005) (Virtual machine ID <GUID>) Source: Hyper-V-VMMS Evend ID: 20100 The Virtual Machine Management Service failed to register the configuration for the virtual machine '<GUID>' at 'C:\ClusterStorage\<PATH>\<VM>': General access denied error (0x80070005) Source: Hyper-V-High-Availability Event ID: 21102 'Virtual Machine Configuration <VM>' failed to register the virtual machine with the virtual machine management service. All other VMs can be moved to/from the offending host, and the offending VM can be moved between the other two hosts. Also, this is not a storage problem, because there are other VMs in the same cluster volume, and the host has no troubles running them. What's going on here?

  Read the article

• One host on a network can't connect to one other host

  - by Max Williams

  I'm on a local network with a few other people. On of the hosts is a virtual machine running in virtualbox on a mac, which has the ip address 192.168.0.35 (the VM that is, not the mac host). Everyone except one guy can connect (ie ping, ssh etc) to that machine. When that one guy tries to ping it he gets Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 which i understand is just how certain mac os's report an unreachable connection. He can ping all the other hosts on the network, ie our computers, and we can all ping the VM fine and connect to it with no problems etc. His ip is 192.168.0.17. I ssh'd onto his machine (as a new user 'anon') and saw the same problems. I can ssh onto the 192.168.0.35 VM as well. From there, i can ping other users, but when i ping the problem guy, it's unreachable that way round as well. He restarted his mac, and was fine for a while. Then, just stopped working again. He's got a different IP to before. Any ideas, anyone? Don't know enough about this stuff to even diagnose the problem. thanks, max

  Read the article

• ESXi 4.0 Guests Locking up

  - by Brendan Sherwin

  I installed ESXi 4.0 on an HP Proliant g5 with a 64bit Xeon processor and took advantage of the free license as I work for a public school. I created two instances of server 2003 from scratch, one to be the DC, DHCP, the other to be a file server and DNS/DHCP backup. I had both guests up and running fine, setup my user accounts, transferred the data, etc etc. Once I joined a client machine to the domain, I would find that both of my Windows guests would lock up. Sometimes it would be for five or so minutes, once it was overnight. The "locked up" state means that as far I could tell, all services were stopped; dhcp no longer handed out IP's, DNS stopped working, I couldn't RDP into the server. The ESXi host, my HP server, was still running fine. VSphere was working, and I could look at the performance of the individual guests.I would try Powering off the hosts from inside VSPhere, and the hosts would start powering off, but get stuck at 95%, and stay that way, sometimes only for 10 minutes, others for hours. Several times I had to restart ESXi from it's console in order to restart my machines. Now, can anyone tell me what is happening, and how I can fix it, or take steps to prevent it? I hired a consultant to come take a look at it, someone who's experience and knowledge I trust, and he told me he had never seen anything like this ever before. He spoke to a friend of his who is VM certified, and he also said he had never heard of this issue. Thanks for your replies, and I'll do my best to respond ASAP. Currently, the server is powered off, and I've reinstituted my nine year old Server 2000 boxes, and I'm considering installing ESXi 3.5. Does anyone know a host created in 4.0 will work in 3.5? I'd really like to avoid having to rebuild those accounts! I know 4.0 works on this server, as I have another server in another school with the same exact hardware running 4.0 fine. Brendan

  Read the article

• pure-ftpd not listening on specified port

  - by Jason McLaren

  I installed the pure-ftpd package (version 1.0.35-1) on an Ubuntu 12.04 box (an EC2 instance based on the standard Ubuntu 12.04 AMI). The pure-ftpd daemon is running (verified with ps), though there is no PID file (expected one to be created by the /etc/init.d/pure-ftpd script). Here's the resulting command that gets run by the init.d script: /usr/sbin/pure-ftpd -l pam -O clf:/var/log/pure-ftpd/transfer.log -o -8 UTF-8 -u 1000 -E -B -g /var/run/pure-ftpd/pure-ftpd.pid Here's my real problem: the ftp server isn't actually listening on any port (checked with netstat and nmap). So I can't ftp to the server (either locally using localhost or remotely using the public IP address). I tried adding a Bind file to /etc/pure-ftpd/conf and restarting, but it didn't help. When I installed pure-ftpd, it replaced inetd with openbsd-inetd, but did not run it since there were no services enabled. So inetd is not listening on port 21 either. (Apparently Ubuntu has a no-inetd-by-default policy, according to https://lists.ubuntu.com/archives/ubuntu-users/2010-September/227905.html .) I want to run pure-ftpd by itself (not with inetd) anyways, since the /etc/init.d/pure-ftpd script requires no inetd if you use the UploadScript feature. I'm not familiar with how Ubuntu handles network services (and can't find any relevant docs besides generic man pages), so I'm probably missing something obvious. Nothing seems out of the ordinary with /etc/hosts.allow (empty) or hosts.deny (empty), and I didn't add any firewall rules (iptables -L shows that the firewall is in its initial state). I've checked the pure-ftpd docs; not sure what else to look at. Any help would be appreciated, thanks!

  Read the article

• Intermittent "Lost connection to MySQL server at 'reading initial communication packet'"

  - by db2

  Our web environment consists of two servers. Web front-end. Dell PowerEdge R610, RHEL 5.5, Apache 2.2.17, php 5.2.14. Database server. Dell PowerEdge R710, Windows 2008 R2 Standard x64, MySQL 5.5.11-log x64. Normally these two work perfectly fine together. However, when I try to get them talking via a dedicated LAN on their secondary NICs (each machine has four of them), things get flaky. I have NIC #2 on both machines configured on the 172.16.1.0/24 subnet, with no gateway or DNS servers (obviously, since it's just those two systems), and I put the private IP address of each machine into the hosts file of the other. The routing tables on both machines look okay after I do this. I've tried this with both a crossover cable draped directly between the two NICs, and also via a dedicated vlan on the switch in the rack. In either case, I get intermittent connection problems. It's a fairly small percentage of connections that fail, but it's enough to cause a significant problem, and I have to switch back to the main network connection, which will contend with all the other traffic and hosts on the switch. The full error message that appears in the application log: SQLSTATE[HY000] [2013] Lost connection to MySQL server at 'reading initial communication packet', system error: 110 Am I doing something really dumb that's causing this to not work properly? Anything I can check in MySQL that would explain why it's failing to connect occasionally?

  Read the article

• Virtual bridged networking with VLAN, could not ping

  - by v.yegy

  I require a virtual network with VLAN be build between two virtual hosts - which can be (lxc/ vbox -ubuntu or win xp). I tried with lxc and vbox with Ubuntu and was finding difficult to make it work without vlan, but was successful with vbox with xp. vbox-xp1 --- br1 ---------------- br2 ---- vbox-xp2 The config is: brctl addbr br1; brctl addbr br2 ifconfig br1 up; ifconfig br2 up stp br1 off; stp br2 off ip link add name br1-br2-l0 type veth peer name br1-br2-l1 sudo brctl addif br1 br1-br2-l0 sudo brctl addif br2 br1-br2-l1 vbox - xp 1 and 2 with network ; bridged and br1 and br2 respectively. The adapter is intel PRO/1000 MT Server and driver installed in guests. Configured IPs and two hosts pinged! VLAN config: ip link add link br1 name br1-2.5 type vlan id 5 brctl addif br2 br1-2.5 create vlan 5 in xp 1 and 2 and assign ip address Ping on with this config does not work. Wireshark trace on interface br1-br2-l1 / br1-2.5 shows that one ping results in ~240 ping packets and each growing by 4 bytes - first one being correct and 60, ping does not reach other host as I see mac is not learnt[arp -a]. -- if br1-2.5 is not configured, I see untagged packets in br1-br2-l1/0, but still not reaching other host as mac is not learnt. if br1-br2-l0/1 is made down, even if br1-2.5 is up, I count not see any packets. I tried with ebtables, but still could not make a correct config to work. -- If any one here are aware of any configuration, please let me know. I need to make a network of switches. Seems I have a very long way. Sorry for a very long question. Thanks and regards, vy

  Read the article

• Setting Up VirtualHosts for a local RubyOnRails Application

  - by chris Frisina

  I want to set up a VirtualHost so that when I type the project name in the address bar, it goes to the home page of the project. httpd-vhosts.conf files in both XAMPP configuration and apache configuration: <VirtualHost project> ServerAdmin [email protected] ServerName project DocumentRoot /Users/path/to/project/public <Directory "/Users/path/to/project/public"> Options Includes FollowSymLinks AllowOverride All Order deny,allow Allow from all </Directory> RewriteEngine On RewriteOptions inherit </VirtualHost> I have also tried with the path directly to the project folder, and not the public folder of the project. the httpd.conf of XAMPP and apache : # Virtual hosts Include /Applications/XAMPP/etc/extra/httpd-vhosts.conf the /etc/hosts file: 127.0.0.1 other1 127.0.0.1 other2 127.0.0.1 project I have tried : 127.0.0.1 project 127.0.0.1:3000 project 127.0.0.1 project:3000 I have also restarted the rails server and the XAMPP server many times after changes. I have it working so that the project:3000/ works, but how do I get it so that I dont have to specify the port number? Notes: All other VHosts are working well. Rails 3.2.8 (willing to change) Ruby 1.9.3 WEBrick server

  Read the article

• Server Names Inside Private Network

  - by thyandrecardoso

  Our office has a private network, where any requests on a (pre-determined) public IP are forwarded to a private IP inside said network. On that private IP, we've got a server running several services, including HTTP servers, and SCM systems. We only control our private network, having no control on the public IP configuration. We bought a domain name, and pointed it to that public IP, so people can access our services from the outside. But, when inside the office, people can't use that DNS name, because the server and any other hosts inside the network share the same public IP! For desktops, inside the office network, dealing with names is really easy: one entry on the hosts file and we're done. However, for laptops, that keep going in and out, and need to access services inside the office, the naming is really annoying. I don't know the "standard" process for dealing with these kind of situations. I've considered installing BIND in the office, and make people configure their wireless and wired connections to use that DNS server. What is the correct approach in this situation? If using BIND (or any other DNS server) is the answer, how should I configure it so that people inside the office can use it to get our custom names, and get forwarded to the ISP DNS when trying to reach the internet?

  Read the article

• different nmap results

  - by aasasas

  Hello I have a scan on my server form outside and from inside, why results are different? [root@xxx ~]# nmap -sV -p 0-65535 localhost Starting Nmap 5.51 ( http://nmap.org ) at 2011-02-16 07:59 MSK Nmap scan report for localhost (127.0.0.1) Host is up (0.000015s latency). rDNS record for 127.0.0.1: localhost.localdomain Not shown: 65534 closed ports PORT STATE SERVICE VERSION 22/tcp open ssh OpenSSH 4.3 (protocol 2.0) 80/tcp open http Apache httpd 2.2.3 ((CentOS)) Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 7.99 seconds AND sh-3.2# nmap -sV -p 0-65535 xxx.com Starting Nmap 5.51 ( http://nmap.org ) at 2011-02-16 00:01 EST Warning: Unable to open interface vmnet1 -- skipping it. Warning: Unable to open interface vmnet8 -- skipping it. Stats: 0:07:49 elapsed; 0 hosts completed (1 up), 1 undergoing SYN Stealth Scan SYN Stealth Scan Timing: About 36.92% done; ETC: 00:22 (0:13:21 remaining) Stats: 0:22:05 elapsed; 0 hosts completed (1 up), 1 undergoing Service Scan Service scan Timing: About 75.00% done; ETC: 00:23 (0:00:02 remaining) Nmap scan report for xxx.com (x.x.x.x) Host is up (0.22s latency). Not shown: 65528 closed ports PORT STATE SERVICE VERSION 21/tcp open tcpwrapped 22/tcp open ssh OpenSSH 4.3 (protocol 2.0) 25/tcp open tcpwrapped 80/tcp open http Apache httpd 2.2.3 ((CentOS)) 110/tcp open tcpwrapped 143/tcp open tcpwrapped 443/tcp open tcpwrapped 8080/tcp open http-proxy?

  Read the article

• fail2ban log parsing too slow on Raspberry Pi - options? [migrated]

  - by Gordon Morehouse

  I'm running fail2ban on a Raspberry Pi at 950MHz which I cannot overclock further. The Pi is occasionally subject to SYN floods on particular ports. I've set up iptables to throttle the rate of SYNs on the port of interest; when the throttle limits are exceeded, hosts which send SYNs are dropped into the REJECT chain and the particular SYN packet which exceeded the limit is logged. fail2ban then watches for these logged SYNs and, after seeing a few, temporarily bans the host for a short time (this is a transient issue in the app I'm working with). The problem is that the SYN floods can occasionally reach rates which are too fast for fail2ban to keep up with; I'll see 20-40 log messages per second, and eventually fail2ban falls behind and becomes ineffective. To add insult to injury, it continues consuming a LOT of CPU as it tries to catch up. I have verified that DROP chained packets from hosts already banned by fail2ban are not logged, and thus do not add to its load. What are my options here? I have a few ideas, but no clear path forward. Could I make the log-parse regex "easier" so it takes fewer cycles? Would using iptables --log-prefix to put a token near the start of the log message, and/or otherwise simplifying/altering the fail2ban regex help? Here is the current fail2ban config line containing a regex: failregex = kernel:.*?SRC=(?:::f{4,6}:)?(?P<host>[\w\-.^_]+) DST.*?SYN Is there a faster way for fail2ban to watch for the packets exceeding the limits than parsing kern.log? Could fail2ban be run under PyPy instead of CPython with minimal nonstandard wizardry (the OS is Raspbian 7, so, mostly Debian 7)? Is there something better than fail2ban that I could use to watch for the packets which exceed the SYN limits, and after N exceeds in X seconds, temporarily put the offending IP into the iptables DROP bucket, and take it out when the ban timer expires? Again, I'd vastly prefer a solution that uses as much software available in Debian as possible, though I can build Debian packages in a pinch.

  Read the article

• Debugging Samba/CUPS printer sharing with Windows

  - by mrdrbob

  I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

  Read the article

• How do I make dnsmasq serve IP addresses via IPoIB?

  - by Matt

  I have a cluster farm that I'm setting up. The nodes (computers in the farm) are connected via ethernet & IP over Infiniband. I'm needing to netboot the nodes and thought dnsmasq would fit well as it provides all the features including support for DHCP over IB and it works great for our ethernet setup. However, I can't seem to get it to provide IP addresses to the infiniband adaptors on the nodes. Each node is running an Ubuntu desktop 12.04 LTS. The dnsmasq server is running on ubuntu server 12.04LTS and has the following test config: dhcp-authoritative domain-needed bogus-priv expand-hosts no-hosts domain=local dhcp-range=eth0,10.0.0.10,10.0.0.255,12h dhcp-option=eth0,3,10.0.0.1 dhcp-range=ib0,10.1.1.10,10.1.1.255,12h dhcp-option=ib0,3,10.1.1.1 log-queries log-dhcp IPoIB works between nodes when configured statically but not with dhcp. On the nodes the file /etc/network/interfaces contains auto lo iface lo inet loopback auto ib0 iface ib0 inet dhcp #iface ib0 inet static #address 10.1.1.5 #netmask 255.0.0.0 up echo connected >`find /sys -name mode | grep ib0` Is there something I need to do on the client or server end to make this work?

  Read the article

• VirtualHost not using correct SSL certificate file

  - by Shawn Welch

  I got a doozy of a setup with my virtual hosts and SSL. I found the problem, I need a solution. The problem is, the way I have my virtual hosts and server names setup, the LAST VirtualHost directive is associating the SSL certificate file with the ServerName regardless of IP address or ServerAlias. In this case, SSL on www.site1.com is using the cert file that is established on the last VirtualHost; www.site2.com. Is this how it is supposed to work? This seems to be happening because both of them are using the same ServerName; but I wouldn't think this would be a problem. I am specifically using the same ServerName for a purpose and I really can't change that. So I need a good fix for this. Yes, I could buy another UCC SSL and have them both on it but I have already done that; these are actually UCC SSLs already. They just so happen to be two different UCC SSLs. <VirtualHost 11.22.33.44:80> ServerName somename ServerAlias www.site1.com UseCanonicalName On RewriteEngine On RewriteOptions Inherit </VirtualHost> <VirtualHost 11.22.33.44:443> ServerName somename ServerAlias www.site1.com UseCanonicalName On SSLEngine on SSLCertificateFile /usr/local/apache/conf/ssl.crt/cert1.crt SSLCertificateKeyFile /usr/local/apache/conf/ssl.key/cert1.key SSLCertificateChainFile /usr/local/apache/conf/chain/gd_bundle.crt RewriteEngine On RewriteOptions Inherit </VirtualHost> <VirtualHost 55.66.77.88:80> ServerName somename ServerAlias www.site2.com UseCanonicalName On RewriteEngine On RewriteOptions Inherit </VirtualHost> <VirtualHost 55.66.77.88:443> ServerName somename ServerAlias www.site2.com UseCanonicalName On SSLEngine on SSLCertificateFile /usr/local/apache/conf/ssl.crt/cert2.crt SSLCertificateKeyFile /usr/local/apache/conf/ssl.key/cert2.key SSLCertificateChainFile /usr/local/apache/conf/chain/gd_bundle.crt RewriteEngine On RewriteOptions Inherit </VirtualHost>

  Read the article

• Hiding a Website from Search Engine Bots and Viewers by Disabling Default VirtualHost

  - by Basel Shishani

  When staging a website on a remote VPS, we would like it to be accessible to team members only, and we would also like to keep the search engine bots off until the site is finalized. Access control by host whether in Iptables or Apache is not desirable, as accessing hosts can vary. After some reading in Apache config and other SF postings, I settled on the following design that relies on restricting access to only through specific domain names: Default virtual host would be disabled in Apache config as follows - relying on Apache behavior to use first virtual host for site default: <VirtualHost *:80> # Anything matching this should be silently ignored. </VirtualHost> <VirtualHost *:80> ServerName secretsiteone.com DocumentRoot /var/www/secretsiteone.com </VirtualHost> <VirtualHost *:80> ServerName secretsitetwo.com ... </VirtualHost> Then each team member can add the domain names in their local /etc/hosts: xx.xx.xx.xx secrethostone.com My question is: is the above technique good enough to achieve the above said goals esp restricting SE bots, or is it possible that bots would work around that. Note: I understand that mod_rewrite rules con be used to achieve a similar effect as discussed here: How to disable default VirtualHost in apache2?, so the same question would apply to that technique too. Also please note: the content is not highly secretive - the idea is not to devise something that is hack proof, so we are not concerned about traffic interception or the like. The idea is to keep competitors and casual surfers from viewing the content before it's released, and to prevent SE bots from indexing it.

  Read the article

• Filtered Router Interface

  - by jviotti

  I'm having some problems with a Scientific-Atlanta DPR2320R2. In specific with the WIFI. A few months ago I changed its password and username and now I can't remember. So I tried cracking it with Hydra but it drove things worse. Content of webadmin was rendered partial, and threw lot of errors. I then reseted the router. I found myself abled to browse the web with ethernet-connected pc. Wifi is configured by registering the device's MAC Address, and indeed the router has been reseted and register MAC address were lost. No device could connect to wifi. In fact, the device does not even recognize the network. I tried the pointing to 192.168.0.1 to restablish the MAC's. But I couldn't connect to the router access point. Tried listing up hosts: $ nmap -sP 192.168.0.0/24 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:18 ART Host 192.168.0.1 is up (0.0018s latency). Host 192.168.0.11 is up (0.00025s latency). Nmap done: 256 IP addresses (2 hosts up) scanned in 59.62 seconds Then checked 192.168.0.1 was really up by sending pings. It responded to all my pings. I quick-scanned the access point: $ nmap 192.168.0.1 Starting Nmap 5.00 ( http://nmap.org ) at 2012-12-11 01:08 ART Interesting ports on 192.168.0.1: Not shown: 999 closed ports PORT STATE SERVICE 80/tcp filtered http Nmap done: 1 IP address (1 host up) scanned in 6.73 seconds Look the state of the port 80: FILTERED. I'm pretty confused now. Any suggestion would be appreciated. Thanks in advance.

  Read the article

• With WebMatrix, How do I Connect to a MySQL Database on a Colleague's Machine?

  - by Ash Clarke

  I have scoured Google trying to discover how to do this, but essentially I want to connect to a colleague's MySQL database for working together on a Wordpress installation. I am having no luck and keep getting an error about the connection not being possible: Unable to connect to any of the specified MySQL hosts. MySql.Data.MySqlClient.MySqlException (0x80004005): Unable to connect to any of the specified MySQL hosts. at MySql.Data.MySqlClient.NativeDriver.Open() at MySql.Data.MySqlClient.Driver.Open() at MySql.Data.MySqlClient.Driver.Create(MySqlConnectionStringBuilder settings) at MySql.Data.MySqlClient.MySqlPool.GetPooledConnection() at MySql.Data.MySqlClient.MySqlPool.TryToGetDriver() at MySql.Data.MySqlClient.MySqlPool.GetConnection() at MySql.Data.MySqlClient.MySqlConnection.Open() at Microsoft.WebMatrix.DatabaseManager.MySqlDatabase.MySqlDatabaseProvider.TestConnection(String connectionString) at Microsoft.WebMatrix.DatabaseManager.IisDbManagerModuleService.TestConnection(DatabaseConnection databaseConnection, String configPathState) at Microsoft.WebMatrix.DatabaseManager.Client.ClientConnection.Test(ManagementConfigurationPath configPath) at Microsoft.WebMatrix.DatabaseManager.Client.DatabaseHierarchyInfo.EnsureLoaded() The connection details are copied from my colleague's connection string, with the exception of the server being modified to match the IP address of his machine. I'm not sure if there is a firewall port I have to open or a configuration file I have to modify, but I'm not having much luck so far. (There is a strong chance that, by default, web matrix / iis express doesn't set the mysql database it creates to accept remote connections. If anyone knows how to change this, that would be grand!) Anyone have any ideas?

  Read the article

• How to connect a VM running on an ESXi host to that host via a VMKernel NIC?

  - by Zac B

  Say I have an ESXi (5.0) host that runs a Linux distribution which hosts iSCSI targets, which contain the images for other VMs which the host will run. When it's used, I'll start the host first, then the iSCSI server, and then refresh all storage targets/HBAs in order to see the provided shares as online. I know it's a strange puzzle-box solution, but I was told to implement it. The ESXi host itself has a gigabit NIC which connects to the outside world. The guest OS (CentOS) supports VMXNet3, however, and if I can, I'd like to use its VMXNET3 NIC to host iSCSI for the ESXi host. How should I go about doing this? I went to create a new virtual network, and selected "VKernel", as it suggested that I use that type of network for SAN traffic, but it is apparently not set up for "self-hosted" SAN hosts, as the new network did not appear as an option to attach the CentOS box's VMXNET3 NIC to. How should I best connect an iSCSI host out to its "parent" ESXi host, if I need a) a 10gb connection, and (optionally) b) a VMKernel network for it?

  Read the article

• OS X Apache giving 503 error for anything in /api directory

  - by WilliamMayor

  I have a locally hosted website that uses Smarty templates, I'm trying to get started on building an API for the site. I've used virtualhost.sh to create a local virtual host for this and other sites. I've discovered that if I put a directory called api at the root of any of these virtual hosts I will get a 503 error when I try to access anything inside. I am using mod-rewrite but so far only to append a .php extension when needed. Here are the error logs for a request: [Thu Feb 09 13:42:37 2012] [error] proxy: HTTP: disabled connection for (localhost) [Thu Feb 09 13:49:06 2012] [error] (61)Connection refused: proxy: HTTP: attempt to connect to [fe80::1]:8080 (localhost) failed [Thu Feb 09 13:49:06 2012] [error] ap_proxy_connect_backend disabling worker for (localhost) The middle line gave me a clue to look in my hosts file because why would a request go to [fe80::1]:8080? I commented out that line and tried again, this time the error was in connecting to the standard 127.0.0.1 localhost. I have concluded that perhaps there is some config file somewhere picking up the underlying request of localhost/api and pointing it somewhere other than my virtual host. At this point my ability to fix the problem fails me. Can anyone help?

  Read the article

• Moving Farm to co-location hosting - network settings requirements

  - by Saariko

  I am moving my farm (2 Dell's R620) to a co-location hosting service. I am trying to figure out the secure way to have my network settings The requirements are: VM1 is the working HOST, includes: esxi 5.1, vSphere, 4 clients (w2008r2 all) VM2 has esxi 5.1 installed, and a single machine with Veeam Backup and copy 6.5 - keeping a copy of VM1 clients on the VM2 internal storage (this solution is due to a very small budget - in case of failure on Host 1 - can redirect IP's) Only 2 VM clients require network address and access from the WWAN - ISP provides IP's range for them (with Gateway and DNS) I need connection to the iDrac's from my office (option to create a VPN-SSL tunnel) Connection to the vSphere appliances I want to be able to RDP to the VM clients The current configuration is that each host has the iDrac dedicated nic connected , and another (NIC #1) connected - with a static IP on 192.168.3.x The iDrac's have a static IP from the same network range (19.168.3.x) It will look something like this: My thoughts: On NIC#2 of both hosts I will connected a crossed cable I will give each VM clients that needs internet access a 2ndry VM network with the assigned IP from the ISP open only to web - can not access from the My Question: Should I give IP's (external) to the machines who DO NOT require WWAN Access? - I can't see a way to RDP to them directly if not. Should I use the crossed cable? or just plug NIC #2 to the switch? Will this setup even work? What do I need to verify? What Virtual nic's and/or switches should I create on the Hosts?

  Read the article

• apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName

  - by user35402

  I keep getting this warning when I (re)start Apache. Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName ... waiting apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [ OK ] This is the content of my etc/hosts file: #127.0.0.1 hpdtp-ubuntu910 #testproject.localhost localhost.localdomain localhost #127.0.1.1 hpdtp-ubuntu910 127.0.0.1 localhost 127.0.0.1 testproject.localhost 127.0.1.1 hpdtp-ubuntu910 # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts This is the content of my /etc/apache2/sites-enabled/000-default file: <VirtualHost *:80> ServerName testproject.localhost DocumentRoot "/home/morpheous/work/websites/testproject/web" DirectoryIndex index.php <Directory "/home/morpheous/work/websites/testproject/web"> AllowOverride All Allow from All </Directory> Alias /sf /lib/vendor/symfony/symfony-1.3.2/data/web/sf <Directory "/lib/vendor/symfony/symfony-1.3.2/data/web/sf"> AllowOverride All Allow from All </Directory> </VirtualHost> When I go to http://testproject.localhost, I get a blank page can anyone spot what I am doing wrong?

  Read the article

• Debugging Samba/CUPS printer sharing with Windows

  - by mrdrbob

  I've got a HP Deskjet hooked up to a Slackware 12.2 box. I've got CUPS set up and can print a test page from the box just fine. I've also got Samba set up and have a couple file shares that work fine. I'm trying to share that HP Deskjet out via Samba, but I can't get it to show up in any Windows system. I see the server and its file shares in Windows networking, but when I open the Printers, no printer shows up. Running net view \\servername from the command line lists the file shares, but no printers. Here's the pertinent part of my smb.conf, if that helps: [global] workgroup = HOMENET security = share hosts allow = 192.168.1. 192.168.2. 127. load printers = yes printcap name = cups printing = cups log file = /var/log/samba.%m max log size = 50 [printers] comment = All Printers path = /var/spool/samba browseable = no public = yes writable = no printable = yes guest only = yes Can anyone give me some pointers as to where to start looking for potential causes? Update: Running testparm shows no errors. Here's the output (minus the file shares): [global] workgroup = HOMENET security = SHARE log file = /var/log/samba.%m max log size = 50 printcap name = cups hosts allow = 192.168.1., 192.168.2., 127. [printers] comment = All Printers path = /var/spool/samba guest only = Yes guest ok = Yes printable = Yes browseable = No

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >