Search Results

Search found 10844 results on 434 pages for 'device mapper'.

Page 94/434 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

  • Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

    - by Rhys
    I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

    Read the article

  • Windows Phone 8 not interfacing with Zune software

    - by Cyberherbalist
    I just got a Lumia 521 with Windows Phone 8 and am trying to get the device to work with the Zune software on my PC. I still have my Windows Phone 7 device, and the new one is not working the same way. When I plug the WP7 device into the PC's USB port, it automatically fires up Zune and I can sync my podcasts and music etc to the device. But when I plug the Lumia into the PC it doesn't fire up Zune, and if I start Zune manually, it doesn't interface with the phone at all. Perhaps I am missing something and WP8 isn't supposed to use Zune to interface with the phone?

    Read the article

  • Computer wakes itself few seconds after hibernation

    - by Juan Zamudio
    Hi all, this is the situation, this is a Dell Optiplex 755, I recently upgraded it to Windows 7 64 bits, it had Windows XP SP3 previously, on XP I never had a problem hibernating the PC, now with Windows 7 64 every time I hibernate the PC it wakes it self after 5 or so seconds. Here are the steps I already tried: On Windows 7 I enabled the hibernation following this steps In the MoBo the sleep settings are on S3 In the Mobo I disable remote wake ups I have disabled the remote wake up in the NIC When I run the lastwake command I get unknown device or something like that I already disable the wake timers on Windows I have the latest drivers from Intel, but I just found out that in the device Manager I get a warning sign on the "Intel AMT SOL (COM3)" device saying that it failed and windows stopped the device, I reinstalled the Intel drivers but nothing changed. The only thing that I haven't touch is Intel ME in the MoBo but I don't if that could help and what settings are correct. Thanks for you help.

    Read the article

  • Virtualizing an Inline network appliance with VirtualBox (or VMWare)

    - by Tzury Bar Yochay
    My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

    Read the article

  • Netgear Router missing Wireless Configuration Menu Link

    - by ccisystems
    I have a Netgear WiFi router DG834G v3. On it it says it's a WiFi, ADSL 2+ modem, switch, etc. There is an antenna on the back and a WiFi indicator on the front. However, when I connect to it via the web interface, the wireless setup link is missing from the menu. The top label indicates it is a DG834 (without G). I have received it from a friend and was really looking forward to using it but I really need the WiFi part. I looked on Netgear's site as I thought someone must have uploaded the wrong firmware for the device sometime - so I upgraded to the latest firmware, but it still says it's NOT a 'G' device and the wireless menu is nowhere to be found. I'd appreciate a push in the right direction as to what I could do. Is it possible that the WiFi chip is broken or something and the device does not detect it and the firmware reverts the device to a different version?

    Read the article

  • How to log kernel panics without KVM

    - by Spacedust
    My server is crashing and I can't find an answer why. It all started after my datacenter upgrade RAM from 16 GB to 32 GB. I also found such logs in dmesg - they've started to show itself just before the first kernel panic: EXT4-fs error (device md2): ext4_ext_find_extent: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_ext_remove_space: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 20974: 8589 blocks in bitmap, 54896 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. EXT4-fs error (device md2): ext4_ext_split: inode #97911179: (comm pdflush) eh_entries 28769 != eh_max 26988! EXT4-fs (md2): delayed block allocation failed for inode 97911179 at logical offset 1039 with max blocks 1 with error -5 This should not happen!! Data will be lost EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 21731: 5 blocks in bitmap, 60762 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. My system is CentOS 5.8 64-bit with latest kernel 2.6.18-308.20.1.el5. How can I check what is the reason of kernel panic without having an access to the KVM ? I have told my datacenter admins to check the memory in the server.

    Read the article

  • install bluetooth in samsung R430, windows 7

    - by voodoomsr
    how can i install the bluetooth driver in this laptop in windows 7. The installation process tells me that i need to activate the bluetooth device to continue, but how can i activate if till that moment the device doesn't exist. There isn't any button or switch to activate the device manually. Edited: it's the np-r430 model. I read somewhere (a users forum, not official info) that for Chile and Argentina this models doesn't have built in the bluetooth device, but the US models have it. Maybe for some political and weird reason they send to south american laptops without that. The link of my notebook's specifications in an AR domain: np-r40

    Read the article

  • Raid1 with active and spare partition

    - by Daniel Baron
    I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated. Current Solution I found a solution to my problem, but I am not sure that this is the actual way to do it. Having a closer look at my raid I found that sdb5 was always listed as a spare device: mdadm --examine /dev/sdb5 [...] Number Major Minor RaidDevice State this 2 8 21 2 spare /dev/sdb5 0 0 0 0 0 removed 1 1 8 5 1 active sync /dev/sda5 2 2 8 21 2 spare /dev/sdb5 so readding the device sdb5 to the array md3 always ended up in adding the device as a spare. Finally I just recreated the array mdadm --create /dev/md3 --level=1 -n2 -x0 /dev/sda5 /dev/sdb5 which worked. But the question remains open for me: Is there a better way to manipulate the summaries in the superblock and to tell the array to turn sdb5 from a spare disk to an active disk? I am still curious for an answer.

    Read the article

  • HDMI Sound for HTPC

    - by Brent Arias
    I have the (perhaps) the same problem as stated in this other HDMI sound to HTPC question. I tried the advice of clicking on the speaker in the system tray. I can see the HDMI audio device I want to use. That device claims to be functioning properly. But there is no sound, and it won't let me select it as the active audio device. When I click on the troubleshooter, it says that there are no speakers connected. I would think this is because my computer us unable to pipe sound through the video card (preventing the HDMI from carrying it), except that it truly claims that it has an HDMI sound device that is working correctly. So I'm not sure what is wrong at this point. Thoughts? My system is Windows 7 x64. In case it makes a difference, the video card I'm using is this GeForce GTX 560

    Read the article

  • Software for capturing still image snapshots from video input

    - by cantabilesoftware
    What software is available that will let me watch video from a USB video capture device at full PAL/NTSC resolution and capture a still image at a button press? More info: I'm using a KaiserBaas USB capture device (http://www.kaiserbaas.com/kaiser-baas-product-page/converters/video-to-dvd-maker), and want to capture screen shots from a PS2 connected to it. I'd like to play the game at the full PS2 resolution and capture certain scenes. The device has a one-touch snapshot button on it, but I can't seem to make it work and there's no mention of it anywhere in the documentation. The device works and the video appears in Power Producer (the included software), but I think it previews it smaller than the full resolution. I could print screen it, but having to crop will be a pain.

    Read the article

  • Windows 8, NVIDIA graphics recognition fails

    - by Roy Grubb
    I just installed Windows 8 Pro OEM 64-bit (clean install) and it won't properly recognize my graphics adapter. When I installed Win8, it automatically installed the BasicDisplay.sys driver dated 6/21/2006. 6.2.9200.16384 (win8_rtm.120725-1247). Hardware - Mobo:MSi G41M-P33 Combo CPU:Intel CoreDuo 6600 Graphics:NVIDIA GeForce 9400GT *OS* - Windows 8 Pro 64-bit OEM The graphics adapter worked fine in Windows XP. The PC is a generic box, bought locally and its mobo failed recently, so I replaced it with the G41M. Microsoft wouldn't let me re-activate Windows XP with a different mobo, so I installed Win8, which appears to work except as described next. Win8 only partially recognizes the graphics adapter and won't allow NVIDIA latest driver installer to see that it's an NVIDIA card. As a result, OpenGL doesn't work, and this is needed by the software I most use. Other than that the graphics look OK. When I say 'partially recognizes', I mean that via the Control Panel, I can see that the adapter is described as NVIDIA, but the driver remains stuck at Microsoft Basic Display Adapter no matter what I try, including "Update driver..." in adapter properties. Display Screen Resolution Advanced Settings Adapter shows: Adapter Type: Microsoft Basic Display Adapter Chip Type: NVIDIA DAC Type: NVIDIA Corporation Bios Information: G27 Board - p381n17 Don't know what this means ... no mention of 9400GT Total Available Graphics Memory: 256 MB Dedicated Video Memory: 0 MB In fact the adapter has 512MB on-board video memory. System Video Memory: 0 MB Shared System Memory: 256 MB And Control Panel Device Manager Display adapters just shows Microsoft Basic Display Adapter. No other graphics adapter, and no unknown device or yellow question mark. What I have tried so far: 1. Cleared CMOS and reset. Updated BIOS and all mobo drivers as follows: 1st I used Driver Reviver to see if any driver updates were required. It found some but I didn't use that to get the drivers. Then I switched to MSi's own mobo driver utility Live Update 5. This also showed the board needed to update several so I used it to fetch the new drivers. After that it showed that everything was up to date and I checked with Driver Reviver again, which also reported no drivers now needed updating. Rebooted. Went to the NVIDIA site to get the latest graphics adapter driver. Their auto-detect "Option 2: Automatically find drivers for my NVIDIA products" said "The NVIDIA Smart Scan was unable to evaluate your system hardware. Please use Option 1 to manually find drivers for your NVIDIA products." So I downloaded 310.70-desktop-win8-win7-winvista-64bit-international-whql.exe, which lists 9400 GT under supported products, but when I run it, it says: "NVIDIA Installer cannot continue This graphics driver could not find compatible graphics hardware." Connected the display to the on-board Intel graphics (G41 Intel Express), removed the NVIDIA card and rebooted, changed to internal graphics in CMOS. Again it installs the MS Basic Display Adapter, and can't properly run my s/w that needs OpenGL. It runs on other machines with Intel Express graphics (WinXP and 7) Shut down and pulled out the power cord. Held start button to discharge all capacitors. Removed and re-inserted NVIDIA adapter in PCI-E slot and made sure properly seated. Connected the monitor to the card, screwed plug to socket. Reconnected power cord. Started and checked in BIOS that Primary Graphics Adapter was set to PCI-E. Started Windows. Uninstalled MS Basic Display Adapter in Device Manager. Screen blanks briefly, reappears. No Graphics adapter entry was then visible in Device Manager. Restarted PC. MS Basic Display Adapter Visible again in Device Manager. Clicked in Device Manager View Show hidden devices. No other graphics adapter appears, no unknown devices. Rebooted. Tried Scan for Hardware changes. None detected. Tried right-click on MS Basic Display Adapter Properties Driver Update Driver... Search automatically. It replied that it had determined driver was up to date. I checked that there were no graphic driver-related entries in Programs and Features that I could delete (none). Searched for any other drivers with nvidia in their name and deleted them, just keeping the 306.97 installer exe file. Did a Windows Update. Ran GPU-Z which shows (main items): Microsoft Basic Display Adapter GPU G72 BIOS 5.72.22.76.88 Device ID 10DE - 01D5 DDR2 Bus Width 32 Bit Memory size 64MB Driver Version nvlddmkm 6.2.9200.16384 (ForceWare 0.00) / Win8 64 NVIDIA SLI Unknown in the drop-down at the foot, "Microsoft Basic Display Adapter" is the only option If I swap hard disks in that machine to one with a Ubuntu 10.4 installation (originally installed on the same PC), lspci shows "VGA compatible controller as NVIDIA Corporation Device 01d5 (rev a1) (prog-if 00 [VGA controller])" and "kernel driver in use: nvidia" I'm out of ideas for new things to try and would be really grateful of suggestions. Thanks!

    Read the article

  • Using Apache Environment Variables to set custom ErrorDocument

    - by Tad
    I've got a set of RewriteCond rules that test for various mobile devices and then set environment variables like "env=device:.iphone" or "env=device:.smartphone" if the useragent matches an iPhone or Android device. I'm trying to now redirect the user to custom-styled 404/500 server error pages for each device, by way of the error pages. Ideally I'd like to be able to test for a variable being there, and then write in a custom ErrorDocument string. But an apache doesn't seem to work in this case. Any ideas how I can construct if/else tests in an apache conf file for environment vars?

    Read the article

  • Issue with kernel boot [OVH SERVER]

    - by Conner Stephen McCabe
    Trying to install OpenVZ kernel on Centos 6.3, Yes my kernel is installed i can see it in the /boot folder, yes it is Rhel6 and yes it is all up to date, i checked this with yum update. My issue comes when i reboot my server with that kernel set as the default, it doesn't load, below i shall put a copy of my grub.conf file and my menu.lst file. Grub.conf: default=0 timeout=5 title vzkernel (2.6.32-042stab057.1) root (hd0,0) kernel /boot/vmlinuz-2.6.32-042stab057.1 ro root=/dev/sda1 initrd /initramfs-2.6.32-042stab057.1.img title linux centos6_64 kernel /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 root=/dev/sda1 ro root (hd0,0) Now i shall paste in Menu.lst; # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_stock-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Linux OpenVZ (vmlinuz-2.6.32-042stab057.1) root (hd0,0) kernel /boot/vmlinuz-2.6.32-042stab057.1 ro root=/dev/mapper/vg_stock-lv_root rd_LVM_LV=vg_stock/lv_root rd_LVM_LV=vg_stock/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=l$ initrd /initramfs-2.6.32-042stab057.1.img title CentOS (2.6.32-71.el6.x86_64) root (hd0,0) kernel /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 ro root=/dev/mapper/vg_stock-lv_root rd_LVM_LV=vg_stock/lv_root rd_LVM_LV=vg_stock/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFO$ initrd /initramfs-2.6.32-71.el6.x86_64.img # dummy text Somebody mentioned something about OVH having added a script which changes the kernel settings or something, and suggested that we either remove the script or reinstall using a VNC, but we don't know how to go about doing either of these? Really would be great if you guys could help. Thanks in advance.

    Read the article

  • USB keyboard not working under Windows 7 x64?

    - by Comboo
    I have two USB keyboards, one no-name cheap thing and an old Logitech. When I plug them in to my computer they pop up in Device Manager as an "Unknown device" and "USB-receiver", respectively. Both of them fail to install any drivers, neither automatically or through Windows Update. Both keyboards work perfectly on another computer I have with Windows Vista 32-bit. Can this be one of those cases where a device does not work in a 64-bit version of Windows? I doubt it though since I've never had that problem before with any device and I thought that basic things like keyboards would be kind of failsafe. I don't really know how to start debugging this issue. I've tried all the obvious, rebooting, changing the USB port, etc. Are there any generic x64 keyboard drivers you can use? Is there any way to find the manufacturer of the keyboard over USB? There is nothing written on it.

    Read the article

  • Canon HV20 recognized, but no drivers in Windows 7 x64

    - by Tuminoid
    My Canon HV20 camcorder is properly recognized when connected via Firewire to Windows 7 x64, but no drivers are installed for it. Windows or I cannot locate any drivers for it as, but it should be working off-the-shelf. I googled a lot, and found instructions to set IEEE 1394 host to legacy mode via Device Manager, but Windows doesn't offer me the legacy option at all. If I check the properties of Canon&HV20 device in Other devices section it says The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. It used to work just fine on my previous installation of Vista x64 and same hardware :/

    Read the article

  • Passing multiple sets of arguments to a command

    - by Alec
    instances contains several whitespace separated strings, as does snapshots. I want to run the command below, with each instance-snapshot pair. ec2-attach-volume --instance $instances --device /dev/sdf $snapshots For example, if instances contains A B C, and snapshots contains 1 2 3, I want the command to be called like so: ec2-attach-volume -C cert.pem -K pk.pem --instance A --device /dev/sdf 1 ec2-attach-volume -C cert.pem -K pk.pem --instance B --device /dev/sdf 2 ec2-attach-volume -C cert.pem -K pk.pem --instance C --device /dev/sdf 3 I can do either one or the other with xargs -n 1, but how do I do both?

    Read the article

  • Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

    - by Biohazard
    I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

    Read the article

  • A can ping B, B can ping C but A cant ping C. How do i connect A to C (ethernet)?

    - by user16654
    I have a computer at home with ip 192.168.221.xxx I have another computer at work that I can ping and it has 2 ip addresses: 192.168.1.xxx and 192.168.0.xxx. Those last 2 addresses have the same gateway ie 192.168.1.1 . The computer at work is connected to a hub. That hub also has an embedded device connected to it with address 192.168.0.xxx Now from my home computer I cannot ping this embedded device. How would I connect to it without changing the subnetwork it connects to? I can ping the embedded device from my work computer and I can ping the work computer from my home computer. So I am trying to connect to the embedded device from my home computer through my work computer. Port forwarding? how would I establish that on Ubuntu?

    Read the article

  • Recurring Apache 2.0.52 error on CentOS 4 - 'could not create `rewrite_log_lock`'

    - by warren
    I have been seeing a recurring issue on my web server: [Sun May 16 03:10:19 2010] [crit] (28)No space left on device: mod_rewrite: could not create rewrite_log_lock Configuration Failed [Sun May 16 04:10:05 2010] [crit] (28)No space left on device: mod_rewrite: could not create rewrite_log_lock Configuration Failed [Sun May 16 05:10:04 2010] [crit] (28)No space left on device: mod_rewrite: could not create rewrite_log_lock Configuration Failed [Sun May 16 05:17:13 2010] [crit] (28)No space left on device: mod_rewrite: could not create rewrite_log_lock Configuration Failed So far, the only fix I have found to this when it happens is to reboot my server. This is non-ideal :-\ Restarting httpd does not clear the error. df indicates I have 20+ gigs free, and top and free both report 800+ megs (or 1.2 gigs) > df -h Filesystem Size Used Avail Use% Mounted on /dev/simfs 40G 18G 23G 44% / # > free total used free shared buffers cached Mem: 1474560 300832 1173728 0 0 0 -/+ buffers/cache: 300832 1173728 Any ideas on why this would recur, and how to prevent/fix it?

    Read the article

  • Apollo linux boot into single user

    - by Spirit
    We have a device that runs Appolo Linux and I have to boot that device into a single user mode so that i can run a fsck to check the hard drive for errors. I've been goggling this during the past hour and so far I haven't found any specific method on how can I do that on this version on Linux. The device is known formerly as a NFX Cinxi One - now re-branded into BlackStratus LOG Storm. If any of you have any experience with this one you may know it is a device that is used to collect logs from other servers. I know that the above info isn't much but that is everything that I can provide up until now since tomorrow I have to follow up closely on this problem.

    Read the article

  • Could not load drivers - Code 31

    - by alexander7567
    I get this error when installing any network adapter on my computer: The device is not working properly because Windows cannot load the drivers required for this device. (Code 31) I have tried many different adapters and many different drivers. Any ideas? OS: Windows XP Home SP3 Here is the Hardware IDs for the onboard NIC: PCI\VEN_8086&DEV_1050&SUBSYS_2019107B&REV_02 PCI\VEN_8086&DEV_1050&SUBSYS_2019107B PCI\VEN_8086&DEV_1050&CC_020000 PCI\VEN_8086&DEV_1050&CC_0200 Device Manager Screenshot

    Read the article

  • No surround sound over HDMI

    - by Chris A
    I have my Pioneer receiver hooked up to my AMD HD4600m which supports audio output over HDMI. I used to work fine, however, after a recent driver update, it will only output stereo sound. It used to output 5.1 surround sound perfectly. Windows does not seem to recognize the device as capable of 5.1. In the past, 5.1 was given as an option in the configuration window, like this: I can not get it to properly recognize the capabilities of the device. I have tried uninstalling the relevant audio device in device manager, and I have also completely removed and reinstalled the display driver. Any suggestions would be greatly appreciated. Thanks

    Read the article

  • grub refuses to install to raid array

    - by ronno
    I have a software raid 0 setup with dual booting Windows 7 and Ubuntu 12.04. The GRUB bootloader that is already on the hard drive seems to work fine. However, since the latest package update for grub, it refuses to install the new version to the hard disk. grub-install throws the following error: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map. Auto-detection of a filesystem of /dev/mapper/< raid name_RAID0p9 failed. Try with --recheck. If the problem persists please report this together with the output of "/usr/sbin/grub-probe --device-map="/boot/grub/device.map" --target=fs -v /boot/grub" to < [email protected] update-grub pops the same "/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map." every alternate line. I don't understand what exactly is going on. I'm afraid to reinstall the grub package because it might mess up the boot, which currently works fine. Is it safe to just ignore this?

    Read the article

  • Windows XP cannot read DVD burned on Ubuntu

    - by webcrawl
    The story : I have burned a DVD disc on Ubuntu using Brasero. When file burning was complete, I canceled the burning of checksum to DVD. Then I put that DVD on Windows XP (SP3) and copied all the files from DVD to the hard drive (no errors when copying). When that was done I discovered that all copied files are not readable. What is more, all the files on that DVD also shown to be not readable, even though all file names, directories were in their place. What I found out? Windows detect that the disc is in CDFS (CD-ROM File System). Disc is clean as new, have no scratches. All files while opened in Notepad++ look like "NULNULNULNULNUL" in one line. The size of files is normal. Other discs that are recognized as CDFS can be read with no problems. What I tried? Starting CDFS service in Windows registry. Result - a new device in Windows Device Manager (JUBS JGH2ZCT SCSI CdRom Device). Removing my CD/DVD device from Device Manager. Result - Windows restarted the system and reinstalled the driver. So... how to read the DVD, when I have no access to any other PC, any other OS?

    Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >