Search Results

Search found 3121 results on 125 pages for 'leaving employee'.

Page 94/125 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

  • Dell R320 RAID 10 with CacheCade

    - by Geekman
    I'm looking for a higher-performance build for our 1RU Dell R320 servers, in terms of IOPS. Right now I'm fairly settled on: 4 x 600 GB 3.5" 15K RPM SAS RAID 1+0 array This should give good performance, but if possible, I want to also add an SSD Cache into the mix, but I'm not sure if there's enough room? According to the tech-specs, there's only up to 4 total 3.5" drive bays available. Is there any way to fit at least a single SSD drive along-side the 4x3.5" drives? I was hoping there's a special spot to put the cache SSD drive (though from memory, I doubt there'd be room). Or am I right in thinking that the cache drives are simply drives plugged in "normally" just as any other drive, but are nominated as CacheCade drives in the PERC controller? Are there any options for having the 4x600GB RAID 10 array, and the SSD cache drive, too? Based on the tech-specs (with up to 8x2.5" drives), maybe I need to use 2.5" SAS drives, leaving another 4 bays spare, plenty of room for the SSD cache drive. Has anyone achieved this using 3.5" drives, somehow?

    Read the article

  • How to route public static IP to a virtual machine on a vmware ESXi host?

    - by Kevin Southworth
    I have 5 static IPs from my ISP (Comcast) and I have a physical machine with VMware ESXi 4.0 on it that is hosting multiple virtual machines. Right now I am just using the default vmware virtual network (vswitch0) with DHCP from the Comcast IP Gateway Router and everything is working fine. Each virtual machine can access the internet, etc. One of my virtual machines is a webserver (Windows Server 2008) and I want to assign it to 1 of my 5 static IPs so it's accessible from the public internet, while leaving the other VMs on the internal LAN still using DHCP. If I just plug my laptop directly into the Comcast IP Gateway (it has 4 ports on the back) and assign my laptop a Static IP using the windows networking dialogs, then I can hit my laptop from the public internet and it works great. However, if I try to do the same steps to set a static IP config on my Windows Server 2008 VM, it does not work. The VM cannot access the internet (open Firefox and try to visit google.com), and I cannnot see the VM from the public internet either. I'm assuming I'm missing something in the ESXi config somewhere, but I'm pretty new to ESXi and I'm not sure how to configure it to work this way.

    Read the article

  • GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

    - by hurikhan77
    I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

    Read the article

  • No Homegroup Computers, Network Troubleshooter Fails

    - by Mokubai
    I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

    Read the article

  • Ram question in VMware Server 2

    - by ToreTrygg
    Hi, I understand from the VMware Server 2 documentation that VMware Server 2 is capable of running a 64-bit guest OS underneath a 32-bit host OS, as long as the hardware running the box is 64-bit capable. Here's my situation. We currently have an underutilized XEON X3220 Quad Core 64bit Server, running Server 2003, 32-bit and 2gb of RAM (the motherboard is capable of 8gb ram). The server is currently used mainly for file and print services. It is also running Active Directory, Novell eDirectory and Groupwise 6.5. We are planning a micration to Microsoft Exchange, so the Novell eDirectory and Groupwise services will eventually be purged from this box, leaving only Active Directory, File and Print services. Being that this server is underutilized we are hoping to save hardware costs and virtualize our new Exchange investment. My question is this. Will VMware allow access to the "invisible" extra memory that Windows 32-bit won't see. Meaning, if we increase the full amount of system ram to 8gb (yes, I know the 32-bit host OS will only see a maximum of 4gb), will I be able to assign maybe 5gb to the new Server 2008 64-bit OS running Exchange and leave 3gb for the Guest OS (or maybe even a 6, 2 split). The second part of that would be, would it be better to just convert the main OS currently running to an image, convert the machine itself to ESXi and run both OSes as images under ESXi. Downtime for this box is critical, so my preference is most definitly with the first option because it presents very minimal downtime. Doing the second would make downtime quite a few hours to image the machine and then convert the image to a VMware Image.

    Read the article

  • Getting SMB file shares working over a PPTP VPN

    - by Ben Scott
    I'm having issues getting SMB file shares working over a PPTP VPN. The server setup consists of a security device (DrayTek V3300) which passes the PPTP authentication to a SBS2003 server running RRAS. The server is the DC and provides DNS and WINS, the single NIC's name server is set to 127.0.0.1, and DHCP on the DrayTek sets the server IP as the DNS. If I create a new VPN connection in Win7, leaving everything as default apart from the server, username, password and domain, I can: ping everything by IP address resolve IPs with nslookup using their fully-qualified name, as in nslookup fileserver.mydomain.local ping machines by fully-qualified name, as in ping fileserver.mydomain.local However if I try to access a file share: within Explorer, I get "Windows cannot access ..." with "Error code: 0x80004005 Unspecified Error", using net use z: \\fileserver.mydomain.local\share, I get "System error 53 has occurred. The network path was not found." If I add the machine name to my HOSTS file I can use the file share, which is my last-ditch workaround, but I have a number of VPN users and would rather a solution that doesn't involve me trying to hand-edit system files on computers half a country away. If I set the WINS server explicitly in the connection's IPv4 settings I don't have to use the FQN to ping the machine, but that doesn't change anything else.

    Read the article

  • Log Shipping breaking daily on SQL Server 2005

    - by IT2
    I am facing a somewhat serious problem with Log Shipping on SQL Server 2005 and I am having trouble to correct it, so I will try some help from SF's experts. I have a Windows 2003 Server (PROD) that ships transactional log backups to another two servers: STAND1: Windows 2003 Server with SQL Server 2005. STAND2: Windows 2008 R2 Server with SQL Server 2005. The problem is that Log Shipping to STAND2 is breaking for ~ 90 minutes some times of the day and returning back without intervention. The breaking occur at times when the backup file is larger (after reindexing, etc). I can see the message below logged on the COPY job: *** Error: The specified network name is no longer available The copy agent was breaking dozens times a day only to STAND2 server, and after the changes below "only" breaks ~ two times a day: The frequency of the backup job was changed from 5 minutes to 10 minutes. Instead of backing up the 4 databases to the same folder, the log backups are now saved on separated folders for each database. The backup job doesn't run 24hs now, and only for 14 hours a day, when people are working on the database. I configured the SQL Server instances on the three servers to limit the memory, leaving more memory to the OS. Now I don't know what to do. Any help will be much appreciated! Thanks!

    Read the article

  • Whats the best way to update Ubuntu 9.04?

    - by Fu86
    I have a Ubuntu 9.04 server which has no packase support anymore. If I want to update my package lists, I get th following errors: Err http://de.archive.ubuntu.com jaunty-security/multiverse Packages 404 Not Found [IP: 141.30.13.10 80] W: Failed to fetch http://de.archive.ubuntu.com/ubuntu/dists/jaunty/main/binary-amd64/Packages 404 Not Found [IP: 141.30.13.10 80] .... I read at the official Ubuntu-Support-Page, that there is a update-manager-core-Package to upgrade to a new release. Unfortunately I dont have this package installed and I am unable to install it because of the lack of package sources. EDIT: Installing the package update-manager-core from another release doesn't work because it depends on a higher version of python-apt. (Tried with 10.04) $ dpkg -i update-manager-core_0.134.7_amd64.deb Selecting previously deselected package update-manager-core. (Reading database ... 28743 files and directories currently installed.) Unpacking update-manager-core (from update-manager-core_0.134.7_amd64.deb) ... dpkg: dependency problems prevent configuration of update-manager-core: update-manager-core depends on python-apt (>= 0.7.13.4ubuntu3); however: Version of python-apt on system is 0.7.9~exp2ubuntu10. update-manager-core depends on python-gnupginterface; however: Package python-gnupginterface is not installed. dpkg: error processing update-manager-core (--install): dependency problems - leaving unconfigured Errors were encountered while processing: update-manager-core So, whats the best way to upgrade to to current Release without reinstalling the complete (virtual) server?

    Read the article

  • Talking JavaOne with Rock Star Kirk Pepperdine

    - by Janice J. Heiss
    Kirk Pepperdine is not only a JavaOne Rock Star but a Java Champion and a highly regarded expert in Java performance tuning who works as a consultant, educator, and author. He is the principal consultant at Kodewerk Ltd. He speaks frequently at conferences and co-authored the Ant Developer's Handbook. In the rapidly shifting world of information technology, Pepperdine, as much as anyone, keeps up with what's happening with Java performance tuning. Pepperdine will participate in the following sessions: CON5405 - Are Your Garbage Collection Logs Speaking to You? BOF6540 - Java Champions and JUG Leaders Meet Oracle Executives (with Jeff Genender, Mattias Karlsson, Henrik Stahl, Georges Saab) HOL6500 - Finding and Solving Java Deadlocks (with Heinz Kabutz, Ellen Kraffmiller Martijn Verburg, Jeff Genender, and Henri Tremblay) I asked him what technological changes need to be taken into account in performance tuning. “The volume of data we're dealing with just seems to be getting bigger and bigger all the time,” observed Pepperdine. “A couple of years ago you'd never think of needing a heap that was 64g, but today there are deployments where the heap has grown to 256g and tomorrow there are plans for heaps that are even larger. Dealing with all that data simply requires more horse power and some very specialized techniques. In some cases, teams are trying to push hardware to the breaking point. Under those conditions, you need to be very clever just to get things to work -- let alone to get them to be fast. We are very quickly moving from a world where everything happens in a transaction to one where if you were to even consider using a transaction, you've lost." When asked about the greatest misconceptions about performance tuning that he currently encounters, he said, “If you have a performance problem, you should start looking at code at the very least and for that extra step, whip out an execution profiler. I'm not going to say that I never use execution profilers or look at code. What I will say is that execution profilers are effective for a small subset of performance problems and code is literally the last thing you should look at.And what is the most exciting thing happening in the world of Java today? “Interesting question because so many people would say that nothing exciting is happening in Java. Some might be disappointed that a few features have slipped in terms of scheduling. But I'd disagree with the first group and I'm not so concerned about the slippage because I still see a lot of exciting things happening. First, lambda will finally be with us and with lambda will come better ways.” For JavaOne, he is proctoring for Heinz Kabutz's lab. “I'm actually looking forward to that more than I am to my own talk,” he remarked. “Heinz will be the third non-Sun/Oracle employee to present a lab and the first since Oracle began hosting JavaOne. He's got a great message. He's spent a ton of time making sure things are going to work, and we've got a great team of proctors to help out. After that, getting my talk done, the Java Champion's panel session and then kicking back and just meeting up and talking to some Java heads."Finally, what should Java developers know that they currently do not know? “’Write Once, Run Everywhere’ is a great slogan and Java has come closer to that dream than any other technology stack that I've used. That said, different hardware bits work differently and as hard as we try, the JVM can't hide all the differences. Plus, if we are to get good performance we need to work with our hardware and not against it. All this implies that Java developers need to know more about the hardware they are deploying to.”

    Read the article

  • iMac 20inch (Mid 2007) SL DVD Boot Prohibitory Sign

    - by Caitlann Lloyd
    iMac 20inch (Mid 2007 Build) with Ubuntu 12.0.4 How I got in this situation I had a perfectly healthy Intel iMac running Snow Leopard several months ago. Then I got the dreaded spinning gear and several kernel panics. After getting a little frustrated (failing to find a solution online), I found an old macbook installation disk and used it to access Disk Utility. From here, I erased my entire hard drive leaving me with no OS. I then created a Ubuntu DVD and installed Ubuntu onto the system. Now, on Ubuntu, I wine installed Transmac and burned a Single layer copy (with languages, etc. removed to save space) of Snow Leopard onto a 4.7GB DVD. I tried to boot from it and was met with first the grey apple screen and a spinning cog before the grey apple shortly turned into the infamous prohibitory sign. Note: I met this problem previously when using Disk Utility to create a bootable USB of Snow Leopard, hence I severely doubt it has anything to do with the DVD created. Resources at my disposal 1 x iMac running Ubuntu 6 x 4.7GB DVDs 1 x USB Stick 12GB 1 x Windows 7 Laptop Resources I do not have Firewire cables Access to a prebuilt retail disk (Misplaced) Access to another Mac Apple Warranty I would be hugely grateful if someone was able to tell me how to install Snow Leopard again.

    Read the article

  • lvm mirroring space unavailable.

    - by Bryan Ward
    I am trying to migrate my data on lvm to two new disks, and setup mirroring between the two. I have successfully migrated all of the data to the first of the two disks, leaving the second one completely available as a mirror. I verified this using pvdisplay -m /dev/sd{g,h}1 --- Physical volume --- PV Name /dev/sdg1 VG Name vg PV Size 931.51 GiB / not usable 3.19 MiB Allocatable yes PE Size 4.00 MiB Total PE 238466 Free PE 82866 Allocated PE 155600 PV UUID v2nc3j-EFBR-QpuG-xgro-Rm59-fmu6-IB3QcR --- Physical Segments --- Physical extent 0 to 49999: Logical volume /dev/vg/videos Logical extents 0 to 49999 Physical extent 50000 to 99999: Logical volume /dev/vg/home Logical extents 0 to 49999 Physical extent 100000 to 129999: Logical volume /dev/vg/music Logical extents 0 to 29999 Physical extent 130000 to 155599: Logical volume /dev/vg/videos Logical extents 50000 to 75599 Physical extent 155600 to 238465: FREE --- Physical volume --- PV Name /dev/sdh1 VG Name vg PV Size 931.51 GiB / not usable 3.19 MiB Allocatable yes PE Size 4.00 MiB Total PE 238466 Free PE 238466 Allocated PE 0 PV UUID LuTrem-WcsZ-qw7l-2CDS-lLKI-wdq0-QEXhLf --- Physical Segments --- Physical extent 0 to 238465: FREE Then when I try to mirror the home logical volume for example, it says that I do not have sufficient space. I used lvconvert -m1 vg/home and the output was: Insufficient suitable allocatable extents for logical volume : 50000 more required Unable to allocate extents for mirror(s). This puzzling to me because it appears as if there is plenty of space on the second disk to mirror. Is there something I have done wrong here? Or is there a way to explicitly tell LVM where to put each leg of the mirror? I'm using lvm2.

    Read the article

  • System State Backup Retention Policies

    - by isoscelestriangle
    I was wondering if there was a general consensus on how long to keep system state backups. I am trying to reevaluate our current backup process, and trying to get a good handle on our current storage requirements. Our current setup involves tapes and sending backups offsite with Barracuda Networks. We have been doing our system state backups with Barracuda now, which does full backups daily, leaving our storage requirements growing quite quickly. My boss is a little too gung-ho with backups and wants our system states saved for quite a while. We currently have 5 days of nightlies, 5 weeklies, 3 monthlies, and so on. I think this is quite overkill for system state backups. My boss wants the ability to go back in time to find when an issue appeared, but I don't think that is practical. Many things change in the course of several months. I also think it would be hard not to notice problems with our DCs and other servers for several months. I would think that a previous week's snapshot and the current week's dailies would suffice. Any advice or reading you can point me to? Thanks!

    Read the article

  • SSD/HDD not exceeding 120 MB/s

    - by skiwi
    SO here is the situation: First this was my old PC, it had a 2x 1TB RAID 0 and a Corsair Force 3 SSD in it. This were the old speeds, measured by HDTune Pro. 2x 1TB RAID 0: Corsair Force 3 SSD Then my dad got my PC and we had several issues, in the end turned out both RAID and SSD controller were malfunctioning causing BlueScreens on 100% load. Removed the RAID 0, but leaving the HDD's intact and bought an Samsung 840 EVO 120GB, though the Corsair SSD is still in the system, just not as sytem disk anymore. 1TB HDD (one of them): Corsair SSD: Samsung SSD: We did not assemble the PC ourselves, so answering some technical questions might be more difficult, though we will do our best. First thing we noticed is that the Samsung 840 EVO is no where reaching it's advertised speed, even an Samsung 840 250GB (non-EVO) is reaching 350 MB/s in my own PC. Then we noticed that both SSD's are capped at 120 MB/s exactly, not sure if this is being caused by HDTune Pro, but very unlikely. And even worse, the Corsair Forza 3 was running faster before the system got reassembled. Does anyone have any clue what is going on?

    Read the article

  • Microsoft Certifications &ndash; how to prep? and why?

    - by Kelly Jones
    I often get asked by my colleagues, “how do you prepare for Microsoft exams?” Well, the answer for me is a little complicated, so I thought I’d write up here what I do. The first thing I do is go to Microsoft’s website to find the exam that I need to take.  If you’re looking to get a particular certification, then their site lists the exam or exams that you’ll need to pass.  If you’ve already taken an exam, you can log onto the MCP website and use their certification planner.  This little tool tells you what tests you need, based on the exams you’ve already passed.  It is very helpful with the certifications that are multiple tests and especially ones that have electives. Once you’ve identified the test, you can use Microsoft’s website to see the topics that it covers.  This is a good outline to follow when you study.  I’ll keep this handy to reference back throughout my studying to make sure that I’m covering all the topics I need to know. The next step is probably where I am a little different from others.  IF the exam outline covers material that I’ve already been working with, then I’ll skip a lot of the studying and go directly to the practice tests.  However, if I’m looking at the outline and wondering how in the world do you do that? – then it’s time to hit the books. So, where to find study materials?  Try typing in the exam number into any search engine.  You’ll typically find a ton of resources.  If you’re lucky, you’ll find books that others recommend based on their studying and exam experience.  As a Sogeti employee, I have access to three really good resources: an internal company list of all of the consultants who have passed particular tests (on our Connex website), Books 24x7, and Transcender practice exams. Once my studying is done (either through books or experience), I’ll go through the practice exams.  I find them really helpful in getting my knowledge lined up to the thinking process that the exam writers use.  If I’m relying on my experience, then this really helps me to identify gaps in my knowledge that I’ll need to fill. That’s about it.  If I’m doing ok on the practice exams, then I’ll take the real thing.  I’ve found that the practice exams are usually more difficult than then real thing. Oh – one other thing I do related to Microsoft exams – I try to take any beta exams that Microsoft makes available that fall into my skill set.  Microsoft has started a blog to announce these and the seats usually fill up really quick.  The blog is at http://blogs.technet.com/betaexams/ . You don’t get your results instantly, like a normal exam, instead you have to wait for everyone to finish taking the beta exams and for Microsoft to determine which questions they are using and which they are dropping.  So, be prepared to wait six to eight weeks for your results.

    Read the article

  • Acer Aspire One -- strange battery problem, charges only up to ~90%

    - by houbysoft
    I have this strange problem on the acer aspire one d250. It happened already once before, stayed for about two weeks, and then "fixed itself". The problem is as follows: the battery can't seem to get fully charged; ie the indicator is stuck at about 90% (it's probably not a software problem -- I have ArchLinux and Windows 7 installed and both report exactly the same) and it never passes that value, but it still shows the status as "charging" (I tried everything I could think of -- leaving it charging for extremely long amounts of time, doing a few complete charge-recharge cycles, removing/reinserting the battery, cleaning the connectors, even updating the BIOS, etc., and nothing helped). Also, when it is getting charged, it charges pretty fast until about 70% and then progresses extremely slowly. The battery holds the charge that appears on the battery indicator normally. Just can't get the battery to charge fully -- I can't get it past the 90%. At first I thought this would be a simple battery failure (even if the computer is not that old, about 6-7 months), but as I mentioned it happened once before, and then one day it fixed itself. I tried contacting Acer about this, but the support was not helpful, completely stupid, it seemed like they used canned responses, the usual. Any thoughts on how to fix this?

    Read the article

  • Installing checkinstall on x86_64 bit

    - by SephMerah
    I downloaded the source for check install. checkinstall-1.6.2.tar.gz. I then tar -xzvf checkinstall-1.6.2.tar.gz Then I make. It prints this error: [root@ip-50-63-180-135 checkinstall-1.6.2]# make for file in locale/checkinstall-*.po ; do \ case ${file} in \ locale/checkinstall-template.po) ;; \ *) \ out=`echo $file | sed -s 's/po/mo/'` ; \ msgfmt -o ${out} ${file} ; \ if [ $? != 0 ] ; then \ exit 1 ; \ fi ; \ ;; \ esac ; \ done make -C installwatch make[1]: Entering directory `/home/sofiane/checkinstall-1.6.2/installwatch' gcc -Wall -c -D_GNU_SOURCE -DPIC -fPIC -D_REENTRANT -DVERSION=\"0.7.0beta7\" installwatch.c installwatch.c:2942: error: conflicting types for 'readlink' /usr/include/unistd.h:828: note: previous declaration of 'readlink' was here installwatch.c:3080: error: conflicting types for 'scandir' /usr/include/dirent.h:252: note: previous declaration of 'scandir' was here installwatch.c:3692: error: conflicting types for 'scandir64' /usr/include/dirent.h:275: note: previous declaration of 'scandir64' was here make[1]: *** [installwatch.o] Error 1 make[1]: Leaving directory `/home/sofiane/checkinstall-1.6.2/installwatch' make: *** [all] Error 2 I searched extensively on this issue and this solution looks promising. Should I attempt to install checkinstall as an fpm? What would be the best way to go about that? Centos 6.3 x86_64

    Read the article

  • SQL Server architecture - they want to move my database to new instance...Why?

    - by O'MALLEY
    Our current production database environment contains about 10 similarily managed databases. Our agency has just purchased and is installing new blade chasses and wants to move my database to a new instance (leaving the other 9 on another). This decision is being driven by one of our IT staff, not a DBA. I am a project manager, not a DBA but I know enough to not necesarrily have a good feeling about this decision and I am urging our IT department to make a sound decision based on what is best for the database. Our IT department has stated that it is not good to have all our eggs in one basket, and has also stated that my database contains "regulatory data" so it should be on its own instance. A couple of truths: - None of the databases on the current instance are OLTP databases nor are any of them data warehouses - My database currently has joins/views to a couple of the other databases in the production environment So my questions are as follows: Am I wrong to disregard a statement about eggs in baskets? (hello, this is why we have maintenance plans/disaster recovery plans). I'll mention that other databases also have regulatory data too. What types of questions do I need to ask to determine if this is a sound decicion? (A DBA friend mentioned that if the service level agreement of said database does not radically differ from the others then why do they want to do this?) I have done some research on linked servers. What arguments should I bring forth about the fact that I have views setup that rely on data from other DBs currently?

    Read the article

  • Best usage for a laptop being used as a desktop without removable batteries

    - by Senseful
    After reading the information on http://batteryuniversity.com, I realize that one of the best ways to permanently damage a lithium ion battery is to use the battery at a high temperature while it's fully charged. This is exactly what happens when you use the computer as if it were a desktop computer, since leaving it plugged in will keep the battery at 100% and using the computer will heat up the battery. This is why it's recommend to remove the battery from your laptop if you are using it is this scenario. My question is what would you do if the laptop doesn't have removable batteries (e.g. a MacBook Pro)? Should I use some kind of charge cycle such as: charge to 80%, unplug the power chord, use the laptop until it reaches 20%, then repeat the cycle by charging to 80% again? If so, which values should I use instead of 80% and 20%? (I think charging to 80% is better than 100% because of the damage that a hot battery at 100% can do, but I just made the figure 80% up, and I'm sure there's a better number to strive for which is backed by science.) I've read many of the articles on batteryuniversity.com, but couldn't find anything pertaining to this. Update: What about doing something like charge (or discharge) it to 50%, then plug it in and turn on settings which use the battery as much as possible (e.g. brightness all the way up, wi-fi on, etc.), in order to try to maintain the battery at 50% (i.e. the rate it is charging is the same as it is discharging). This will probably heat up the battery, but would make it so you don't need to constantly plug and unplug the laptop. The one bad thing is that you are taking up more charge cycles which would decrease the battery life, thus I'm not sure this is a good idea.

    Read the article

  • Upstart can't determine my process' pid

    - by sirlark
    I'm writing an upstart script for a small service I've written for my colleagues. My upstart job can start the service, but when it does it only outputs queryqueue start/running; note the lack of a pid as given for other services. #/etc/init/queryqueue.conf description "Query Queue Daemon" author "---" start on started mysql stop on stopping mysql expect fork env DEFAULTFILE=/etc/default/queryqueue umask 007 kill timeout 30 pre-start script #if [ -f "$DEFAULTFILE" ]; then # . "$DEFAULTFILE" #fi [ ! -f /var/run/queryqueue.sock ] || rm -rf /var/run/queryqueue.sock #exec /usr/local/sbin/queryqueue -s /var/run/queryqueue.sock -d -l /tmp/upstart.log -p $PIDFILE -n $NUM_WORKERS $CLEANCACHE $FLUSHCACHE $CACHECONN end script script #Originally this stanza didn't exist at all if [ -f "$DEFAULTFILE" ]; then . "$DEFAULTFILE" fi exec /usr/local/sbin/queryqueue -s /var/run/queryqueue.sock -d -l /tmp/upstart.log -p $PIDFILE -n $NUM_WORKERS $CLEANCACHE $FLUSHCACHE $CACHECONN end script post-start script for i in `seq 1 5` ; do [ -S /var/run/queryqueue.sock ] && exit 0 sleep 1 done exit 1 end script The service in question is a python script, which when run without error, forks using the code below right after checking command line options and basic environmental sanity, so I tell upstart to expect fork. pid = os.fork() if pid != 0: sys.exit(0) The script is executable, and has a python shebang. I can send the TERM signal to the process manually, and it quits gracefully. But running stop queryqueue claims queryqueue stop/waiting but the process is still alive and well. Also, it's logs indicate it never received the kill signal. I'm guessing this is because upstart doesn't know which pid it has. I've also tried expect daemon and leaving the expect clause out entirely, but there's no change in behaviour. How can I get upstart to determine the pid of the exec'd process

    Read the article

  • The Future of Air Travel: Intelligence and Automation

    - by BobEvans
    Remember those white-knuckle flights through stormy weather where unexpected plunges in altitude result in near-permanent relocations of major internal organs? Perhaps there’s a better way, according to a recent Wall Street Journal article: “Pilots of a Honeywell International Inc. test plane stayed on their initial flight path, relying on the company's latest onboard radar technology to steer through the worst of the weather. The specially outfitted Boeing 757 barely shuddered as it gingerly skirted some of the most ferocious storm cells over Fort Walton Beach and then climbed above the rest in zero visibility.” Or how about the multifaceted check-in process, which might not wreak havoc on liver location but nevertheless makes you wonder if you’ve been trapped in some sort of covert psychological-stress test? Another WSJ article, called “The Self-Service Airport,” says there’s reason for hope there as well: “Airlines are laying the groundwork for the next big step in the airport experience: a trip from the curb to the plane without interacting with a single airline employee. At the airport of the near future, ‘your first interaction could be with a flight attendant,’ said Ben Minicucci, chief operating officer of Alaska Airlines, a unit of Alaska Air Group Inc.” And in the topsy-turvy world of air travel, it’s not just the passengers who’ve been experiencing bumpy rides: the airlines themselves are grappling with a range of challenges—some beyond their control, some not—that make profitability increasingly elusive in spite of heavy demand for their services. A recent piece in The Economist illustrates one of the mega-challenges confronting the airline industry via a striking set of contrasting and very large numbers: while the airlines pay $7 billion per year to third-party computerized reservation services, the airlines themselves earn a collective profit of only $3 billion per year. In that context, the anecdotes above point unmistakably to the future that airlines must pursue if they hope to be able to manage some of the factors outside of their control (e.g., weather) as well as all of those within their control (operating expenses, end-to-end visibility, safety, load optimization, etc.): more intelligence, more automation, more interconnectedness, and more real-time awareness of every facet of their operations. Those moves will benefit both passengers and the air carriers, says the WSJ piece on The Self-Service Airport: “Airlines say the advanced technology will quicken the airport experience for seasoned travelers—shaving a minute or two from the checked-baggage process alone—while freeing airline employees to focus on fliers with questions. ‘It's more about throughput with the resources you have than getting rid of humans,’ said Andrew O'Connor, director of airport solutions at Geneva-based airline IT provider SITA.” Oracle’s attempting to help airlines gain control over these challenges by blending together a range of its technologies into a solution called the Oracle Airline Data Model, which suggests the following steps: • To retain and grow their customer base, airlines need to focus on the customer experience. • To personalize and differentiate the customer experience, airlines need to effectively manage their passenger data. • The Oracle Airline Data Model can help airlines jump-start their customer-experience initiatives by consolidating passenger data into a customer data hub that drives realtime business intelligence and strategic customer insight. • Oracle’s Airline Data Model brings together multiple types of data that can jumpstart your data-warehousing project with rich out-of-the-box functionality. • Oracle’s Intelligent Warehouse for Airlines brings together the powerful capabilities of Oracle Exadata and the Oracle Airline Data Model to give you real-time strategic insights into passenger demand, revenues, sales channels and your flight network. The airline industry aside, the bullet points above offer a broad strategic outline for just about any industry because the customer experience is becoming pre-eminent in each and there is simply no way to deliver world-class customer experiences unless a company can capture, manage, and analyze all of the relevant data in real-time. I’ll leave you with two thoughts from the WSJ article about the new in-flight radar system from Honeywell: first, studies show that a single episode of serious turbulence can wrack up $150,000 in additional costs for an airline—so, it certainly behooves the carriers to gain the intelligence to avoid turbulence as much as possible. And second, it’s back to that top-priority customer-experience thing and the value that ever-increasing levels of intelligence can deliver. As the article says: “In the cabin, reporters watched screens showing the most intense parts of the nearly 10-mile wide storm, which churned some 7,000 feet below, in vibrant red and other colors. The screens also were filled with tiny symbols depicting likely locations of lightning and hail, which can damage planes and wreak havoc on the nerves of white-knuckle flyers.”  (Bob Evans is senior vice-president, communications, for Oracle.)  

    Read the article

  • Setting the default permissions for files uploaded via FTP to a directory

    - by Kerri
    Disclaimer: I'm just a web designer/coder, and server admin stuff is my weakest point of them all. So be easy on me (and very specific). I'm using a simple CMS (Unify) on a site, where part of the functionality is that the client can upload files to a specified directory (using FTP). The permissions for the upload directory are set to 755. But when files are uploaded through the interface, they are uploaded with permissions set to 640 (instead of 644), so site visitors cannot acces the files. When I emailed the CMS's support about this, they told me that it was a server setting, and I need to make sure that files uploaded through FTP are set to 644. Makes perfect sense, but I have no idea how to do this. Any help would be greatly appreciated. This site is a shared site hosted by Network Solutions (Unix), so my access options are limited. I can edit .htaccess files, and php.ini, but that's about all I have access to. It appears I can't even log on via shell. ETA: 11/11/2010 Thanks all. I was able to work around this problem by setting up the CMS's settings in a different way. I'd be interested in following up on Nick O'Niel's suggestions, because I think he's on the right track, but unfortunately I can't access the necessary files on this particular server. So, anyway, I'm leaving this open, since the original questions isn't exactly resolved. Unfortunately, I probably can't put a correct answer to the test, since the shared server in question has nearly all of its config files tightly locked down.

    Read the article

  • TC hashing filters - single rule deletion

    - by exa
    For traffic shaping I'm currently using a setup that looks exactly like the setup from LARTC, on this page: http://lartc.org/howto/lartc.adv-filter.hashing.html I have a simple problem with that - everytime I want to modify something in the hash table (like assign a IP to different flowid), I need to delete the whole filter table and add it again filter by filter. (I actually don't do it by hand, I have a nice program that does it for me... but still...) There is a problem - I got roughly 10k filters allocated this way and deleting and refilling the whole filtertable can get pretty lengthy, which is not exactly good for traffic shaping. My program could easily manage to delete only the rules that need to be deleted (thus reducing the whole problem to several commands and miliseconds), but I simply don't know the command that deletes only the one hashing rule. My tc filter show: filter parent 1: protocol ip pref 1 u32 filter parent 1: protocol ip pref 1 u32 fh 2: ht divisor 256 filter parent 1: protocol ip pref 1 u32 fh 2:a:800 order 2048 key ht 2 bkt a flowid 1:101 match 0a0a0a0a/ffffffff at 16 filter parent 1: protocol ip pref 1 u32 fh 2:c:800 order 2048 key ht 2 bkt c flowid 1:102 match 0a0a0a0c/ffffffff at 16 filter parent 1: protocol ip pref 1 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 link 2: match 00000000/00000000 at 16 hash mask 000000ff at 16 The wish: 'tc filter del ...' command that removes only one specific filter (for example the 0a0a0a0a IP match (IP address 10.10.10.10)). Removal of some small subgroup would also be good - for example I could still recreate a bucket (bkt a) pretty fast. My attempts: I tried to number all the filters using prio, but with no help -- they just create something unusuable (but deletable) below, but the bucketed filters remain there after that gets deleted. Any ideas? edit - I'm adding a simplified tl;dr description of the problem: I created hash filter on some interfce just like in this http://lartc.org/howto/lartc.adv-filter.hashing.html I want to find a command that deletes one rule (e.g. 1.2.1.123) from the table, leaving the rest untouched and working.

    Read the article

  • Finding Leaders Breakfasts - Adelaide and Perth

    - by rdatson-Oracle
    HR Executives Breakfast Roundtables: Find the best leaders using science and social media! Perth, 22nd July & Adelaide, 24th July What is leadership in the 21st century? What does the latest research tell us about leadership? How do you recognise leadership qualities in individuals? How do you find individuals with these leadership qualities, hire and develop them? Join the Neuroleadership Institute, the Hay Group, and Oracle to hear: 1. the latest neuroscience research about human bias, and how it applies to finding and building better leaders; 2. the latest techniques to recognise leadership qualities in people; 3. and how you can harness your people and social media to find the best people for your company. Reflect on your hiring practices at this thought provoking breakfast, where you will be challenged to consider whether you are using best practices aimed at getting the right people into your company. Speakers Abigail Scott, Hay Group Abigail is a UK registered psychologist with 10 years international experience in the design and delivery of talent frameworks and assessments. She has delivered innovative assessment programmes across a range of organisations to identify and develop leaders. She is experienced in advising and supporting clients through new initiatives using evidence-based approach and has published a number of research papers on fairness and predictive validity in assessment. Karin Hawkins, NeuroLeadership Institute Karin is the Regional Director of NeuroLeadership Institute’s Asia-Pacific region. She brings over 20 years experience in the financial services sector delivering cultural and commercial results across a variety of organisations and functions. As a leadership risk specialist Karin understands the challenge of building deep bench strength in teams and she is able to bring evidence, insight, and experience to support executives in meeting today’s challenges. Robert Datson, Oracle Robert is a Human Capital Management specialist at Oracle, with several years as a practicing manager at IBM, learning and implementing latest management techniques for hiring, deploying and developing staff. At Oracle he works with clients to enable best practices for HR departments, and drawing the linkages between HR initiatives and bottom-line improvements. Agenda 07:30 a.m. Breakfast and Registrations 08:00 a.m. Welcome and Introductions 08:05 a.m. Breaking Bias in leadership decisions - Karin Hawkins 08:30 a.m. Identifying and developing leaders - Abigail Scott 08:55 a.m. Finding leaders, the social way - Robert Datson 09:20 a.m. Q&A and Closing Remarks 09:30 a.m. Event concludes If you are an employee or official of a government organisation, please click here for important ethics information regarding this event. To register for Perth, Tuesday 22nd July, please click HERE To register for Adelaide, Thursday 24th July, please click HERE 1024x768 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 -"/ /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Contact: To register or have questions on the event? Contact Aaron Tait on +61 2 9491 1404

    Read the article

  • windows 7 turns off itself everyday at about 9am

    - by Radek
    I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

    Read the article

  • Node.js Build failed: -> task failed (error#2)?

    - by Richard Hedges
    I'm trying to install Node.js on my CentOS server. I run ./configure and it runs perfectly fine. I then run the 'make' command and it produces the following: [5/38] libv8.a: deps/v8/SConstruct - out/Release/libv8.a /usr/local/bin/python "/root/node/tools/scons/scons.py" -j 1 -C "/root/node/out/Release/" -Y "/root/node/deps/v8" visibility=default mode=release arch=ia32 toolchain=gcc library=static snapshot=on scons: Reading SConscript files ... ImportError: No module named bz2: File "/root/node/deps/v8/SConstruct", line 37: import js2c, utils File "/root/node/deps/v8/tools/js2c.py", line 36: import bz2 Waf: Leaving directory `/root/node/out' Build failed: - task failed (err #2): {task: libv8.a SConstruct - libv8.a} make: * [program] Error 1 I've done some searching on Google but I can't seem to find anything to help. Most of what I've found is for Cygwin anyway, and I'm on CentOS 4.9. Like I said, the ./configure went through perfectly fine with no errors, so there's nothing there that I can see. EDIT I've got a little further. Now I just need to upgrade G++ to version 4 (or higher). I tried yum update gcc but no luck, so I tried yum install gcc44, which resulted in no luck either. Has anyone got any ideas as to how I can update G++?

    Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >