Search Results

Search found 22877 results on 916 pages for 'network storage'.

Page 95/916 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

• Network Bridging for WiFi-to-Ethernet in linux

  - by shakaran

  It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• HTTP downloads stop after some time, resuming is not possible

  - by cdauth

  When I try to download a file via HTTP, the downloads sometimes stop after around 30 MB. The download rates goes down to 0 B/s and no data keeps coming. When I stop the download and resume again, the download still hangs. But when I redownload it from byte 0 again, everything works fine up to 30 MB when it stops again. Sometimes, after some hours, it just works again without problems. The position in the file when the download stops is variable, but most of the time it is around 30–35 MB. As a download manager I use wget. The same behaviour happens though using curl and other download managers. The error occurs independently of the server I download from. I have also observed this error on other Linux computers in my network. All computers on my network run Gentoo Linux on x86. All internet connections on my network go through a server on my network which runs a transparent Squid proxy on port 80. That server is connected to a router, which is a Speedport W 700V by Deutsche Telekom AG. That router is connected to the internet using ADSL, with 448 kbit/s down speed and 96 kbit/s up speed. I am almost sure that my transparent proxy is not the problem. I turned that off without resolving the issue. I also connected to the router directly via WLAN without resolving the issue. I also tried to download over another port via HTTP. Furthermore, I tried to download the file using IPv6 with a gateway6 tunnel from my computer, which resulted in exactly the same problem. Now the strange thing is that everything works fine using FTP and HTTPS (also with wget on the same computer). Even more strange: when I resume the download that hanged over HTTP using FTP or HTTPS, download a few bytes that way, stop wget and then resume again using HTTP, it loads data again! But after a few MB, it may stop again. Unfortunately, files downloaded that way are always broken (the MD5 sum is not correct), so at some point, there must have been bogus data. I tried searching for HTML error messages in the downloaded file, but grep -i html does not find anything. (I cannot think of a way to search for GZIP-compressed HTML error messages in the file, so I did not try that.) I tried using strace on wget when it failed to resume a download, you can find the entire output on pastebin. The important lines are repeated every second: clock_gettime(CLOCK_MONOTONIC, {326102, 62176435}) = 0 ) = 1 write(2, "78% [++++++++++++++++++++++++++++"..., 19578% [+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ] 110,683,685 --.-K/s ) = 195 select(4, [3], NULL, NULL, {0, 949999}) = 0 (Timeout) I have absolutely no idea what could be the reason of this problem. It seems like whatever causes the issue speaks HTTP. It seems to speak HTTP that intelligently that it even regognises it in an IPv6-over-IPv4 tunnel. But what could that be and why does it only happen sometimes? The other possibility would be that there is a problem on my computer that is the same on other Gentoo Linux computers as well. Has anyone ever had such a problem? What could be the reason and where do I have to continue investigating to find out more about the issue? Update: I have just run into the problem again and tried to resume the download over the router’s WLAN, and this time it worked. Maybe I did something wrong during my last tests with the WLAN. Now maybe my transparent proxy server is in fact the problem. It is a very basic Squid proxy server that does not cache anything. Maybe the fact is interesting that a second Squid proxy runs on the same computer on another port. Update: A download hung again and this time I turned off all firewall settings and stopped all proxy servers. I failed to resume the download from my network server, which is directly connected to the router. So my proxy server definitely is not the cause the problem. I will try to upgrade the firmware of my router now, although I do not have admin access to it. I will see what I can do.

  Read the article

• Cannot access website from inside network

  - by musclez

  I have a website running from my internal network available at the example IP 192.168.1.5. When I type this in to the browser, it redirects to my domain name ie, "example.com", and gives me Error code: ERR_CONNECTION_REFUSED. Any other machine that is inside of the network can access the website. The website is also accessible outside of the network. Other services from the server, like file sharing or ftp, are available to all machines in the network including the one i'm having issues http issues with. The issue may be linked to a proxy service, but from my understanding the service has been completely disabled and any executable have been uninstalled from the machine. I am wondering if there is some residual proxy information remaining on the machine that limits the connection. I'm fairly positive that "example.com" is what is being blocked by the local machine, and not an IP address being blocked or a faulty connection. When I examine the hosts file, there are no redirects to the local machine for "example.com". There was a rule, as on my other machines within the network: 192.168.1.5 example.com But i have since removed that for troubleshooting purposes. What intrigued me is that when I use the actual IP, the IP address will redirect to the domain in the browser and THEN say ERR_CONNECTION_REFUSED. Server-Side Results The server logs are reporting this: example.com ::1 - - [Date & time] "OPTIONS * HTTP/1.0" 200 126 "-" "Apache/2. 2.22 (Unix) (internal dummy connection)" However, this seems to be irrelevant as it is not triggered when I try to connect to the server with the specified machine. Fiddler results: Host: *example.com* Proxy-Connection: keep-alive Chrome-Side [Fiddler] The connection to 'example.com' failed. Error: ConnectionRefused (0x274d). System.Net.Sockets. SocketException No connection could be made because the target machine actively refused it 01.23.45.67:80 01.23.45.67:80 would be the external IP, which the server and the machine in question both share. I am doing so reading into 0x274d and its coming back with .NET web.config information. I am still at a loss to what to do with this information. I have WireShark running as well. Theres is a lot of sensitive information in the readout and I'm not sure what to extract from it. Either way, if it helps, I can access that information if anyone would like me to. Thanks for the help!

  Read the article

• Slow boot on Ubuntu 12.04, probable cause the network connection

  - by Ravi S Ghosh

  I have been having rather slow boot on Ubuntu 12.04. Lately, I tried to figure out the reason and it seems to be the network connection which does not get connected and requires multiple attempts. Here is part of dmesg [ 2.174349] EXT4-fs (sda2): INFO: recovery required on readonly filesystem [ 2.174352] EXT4-fs (sda2): write access will be enabled during recovery [ 2.308172] firewire_core: created device fw0: GUID 384fc00005198d58, S400 [ 2.333457] usb 7-1.2: new low-speed USB device number 3 using uhci_hcd [ 2.465896] EXT4-fs (sda2): recovery complete [ 2.466406] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.589440] usb 7-1.3: new low-speed USB device number 4 using uhci_hcd **[ 18.292029] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 18.458958] udevd[377]: starting version 175 [ 18.639482] Adding 4200960k swap on /dev/sda5. Priority:-1 extents:1 across:4200960k [ 19.314127] wmi: Mapper loaded [ 19.426602] r592 0000:09:01.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.426739] r592: driver successfully loaded [ 19.460105] input: Dell WMI hotkeys as /devices/virtual/input/input5 [ 19.493629] lp: driver loaded but no devices found [ 19.497012] cfg80211: Calling CRDA to update world regulatory domain [ 19.535523] ACPI Warning: _BQC returned an invalid level (20110623/video-480) [ 19.539457] acpi device:03: registered as cooling_device2 [ 19.539520] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input6 [ 19.539568] ACPI: Video Device [M86] (multi-head: yes rom: no post: no) [ 19.578060] Linux video capture interface: v2.00 [ 19.667708] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 19.763171] r852 0000:09:01.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 [ 19.763258] r852: driver loaded successfully [ 19.854769] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.0/input/input7 [ 19.854864] generic-usb 0003:045E:00DD.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input0 [ 19.878605] input: Microsoft Comfort Curve Keyboard 2000 as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.2/7-1.2:1.1/input/input8 [ 19.878698] generic-usb 0003:045E:00DD.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.1-1.2/input1 [ 19.902779] input: DELL DELL USB Laser Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-1/7-1.3/7-1.3:1.0/input/input9 [ 19.925034] generic-usb 0003:046D:C063.0003: input,hidraw2: USB HID v1.10 Mouse [DELL DELL USB Laser Mouse] on usb-0000:00:1d.1-1.3/input0 [ 19.925057] usbcore: registered new interface driver usbhid [ 19.925059] usbhid: USB HID core driver [ 19.942362] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_2M (0c45:63ea) [ 19.947004] input: Laptop_Integrated_Webcam_2M as /devices/pci0000:00/0000:00:1a.7/usb1/1-6/1-6:1.0/input/input10 [ 19.947075] usbcore: registered new interface driver uvcvideo [ 19.947077] USB Video Class driver (1.1.1) [ 20.145232] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 20.145235] Copyright(c) 2003-2011 Intel Corporation [ 20.145327] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 20.145357] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 20.145402] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 20.145404] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90000674000 [ 20.145407] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 20.145531] iwlwifi 0000:04:00.0: irq 46 for MSI/MSI-X [ 20.145613] iwlwifi 0000:04:00.0: Detected Intel(R) WiFi Link 5100 AGN, REV=0x54 [ 20.145720] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 20.167535] iwlwifi 0000:04:00.0: device EEPROM VER=0x11f, CALIB=0x4 [ 20.167538] iwlwifi 0000:04:00.0: Device SKU: 0Xf0 [ 20.167567] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels [ 20.172779] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. [ 20.172783] Disabling lock debugging due to kernel taint [ 20.250115] [fglrx] Maximum main memory to use for locked dma buffers: 3759 MBytes. [ 20.250567] [fglrx] vendor: 1002 device: 9553 count: 1 [ 20.251256] [fglrx] ioport: bar 1, base 0x2000, size: 0x100 [ 20.251271] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 20.251277] pci 0000:01:00.0: setting latency timer to 64 [ 20.251559] [fglrx] Kernel PAT support is enabled [ 20.251578] [fglrx] module loaded - fglrx 8.96.4 [Mar 12 2012] with 1 minors [ 20.310385] iwlwifi 0000:04:00.0: loaded firmware version 8.83.5.1 build 33692 [ 20.310598] Registered led device: phy0-led [ 20.310628] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.372306] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 20.411015] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000 [ 20.454232] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11 [ 20.545636] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [ 20.545640] cfg80211: World regulatory domain updated: [ 20.545642] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 20.545644] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545647] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545649] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 20.545652] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.545654] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 20.609484] type=1400 audit(1340502633.160:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=693 comm="apparmor_parser" [ 20.609494] type=1400 audit(1340502633.160:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=642 comm="apparmor_parser" [ 20.609843] type=1400 audit(1340502633.160:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=693 comm="apparmor_parser" [ 20.609852] type=1400 audit(1340502633.160:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=642 comm="apparmor_parser" [ 20.610047] type=1400 audit(1340502633.160:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=693 comm="apparmor_parser" [ 20.610060] type=1400 audit(1340502633.160:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=642 comm="apparmor_parser" [ 20.610476] type=1400 audit(1340502633.160:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=814 comm="apparmor_parser" [ 20.610829] type=1400 audit(1340502633.160:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=814 comm="apparmor_parser" [ 20.611035] type=1400 audit(1340502633.160:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=814 comm="apparmor_parser" [ 20.661912] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 20.661982] snd_hda_intel 0000:00:1b.0: irq 47 for MSI/MSI-X [ 20.662013] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 20.770289] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 20.770689] snd_hda_intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 20.770786] snd_hda_intel 0000:01:00.1: irq 48 for MSI/MSI-X [ 20.770815] snd_hda_intel 0000:01:00.1: setting latency timer to 64 [ 20.994040] HDMI status: Codec=0 Pin=3 Presence_Detect=0 ELD_Valid=0 [ 20.994189] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input13 [ 21.554799] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 21.554802] vesafb: scrolling: redraw [ 21.554804] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 [ 21.557342] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90011800000, using 3072k, total 3072k [ 21.557498] Console: switching to colour frame buffer device 128x48 [ 21.557516] fb0: VESA VGA frame buffer device [ 21.987338] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 22.184693] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null) [ 27.362440] iwlwifi 0000:04:00.0: RF_KILL bit toggled to disable radio. [ 27.436988] init: failsafe main process (986) killed by TERM signal [ 27.970112] ppdev: user-space parallel port driver [ 28.198917] Bluetooth: Core ver 2.16 [ 28.198935] NET: Registered protocol family 31 [ 28.198937] Bluetooth: HCI device and connection manager initialized [ 28.198940] Bluetooth: HCI socket layer initialized [ 28.198941] Bluetooth: L2CAP socket layer initialized [ 28.198947] Bluetooth: SCO socket layer initialized [ 28.226135] Bluetooth: RFCOMM TTY layer initialized [ 28.226141] Bluetooth: RFCOMM socket layer initialized [ 28.226143] Bluetooth: RFCOMM ver 1.11 [ 28.445620] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 28.445623] Bluetooth: BNEP filters: protocol multicast [ 28.524578] type=1400 audit(1340502641.076:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=1052 comm="apparmor_parser" [ 28.525018] type=1400 audit(1340502641.076:12): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=1052 comm="apparmor_parser" [ 28.629957] type=1400 audit(1340502641.180:13): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1105 comm="apparmor_parser" [ 28.630325] type=1400 audit(1340502641.180:14): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1105 comm="apparmor_parser" [ 28.630535] type=1400 audit(1340502641.180:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1105 comm="apparmor_parser" [ 28.645266] type=1400 audit(1340502641.196:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1104 comm="apparmor_parser" **[ 28.751922] ADDRCONF(NETDEV_UP): wlan0: link is not ready** [ 28.753653] tg3 0000:08:00.0: irq 49 for MSI/MSI-X **[ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 28.857034] ADDRCONF(NETDEV_UP): eth0: link is not ready** [ 28.871080] type=1400 audit(1340502641.420:17): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1108 comm="apparmor_parser" [ 28.871519] type=1400 audit(1340502641.420:18): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1108 comm="apparmor_parser" [ 28.874905] type=1400 audit(1340502641.424:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1113 comm="apparmor_parser" [ 28.875354] type=1400 audit(1340502641.424:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1113 comm="apparmor_parser" [ 30.477976] tg3 0000:08:00.0: eth0: Link is up at 100 Mbps, full duplex [ 30.477979] tg3 0000:08:00.0: eth0: Flow control is on for TX and on for RX **[ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready** [ 31.110269] fglrx_pci 0000:01:00.0: irq 50 for MSI/MSI-X [ 31.110859] [fglrx] Firegl kernel thread PID: 1327 [ 31.111021] [fglrx] Firegl kernel thread PID: 1329 [ 31.111408] [fglrx] Firegl kernel thread PID: 1330 [ 31.111543] [fglrx] IRQ 50 Enabled [ 31.712938] [fglrx] Gart USWC size:1224 M. [ 31.712941] [fglrx] Gart cacheable size:486 M. [ 31.712945] [fglrx] Reserved FB block: Shared offset:0, size:1000000 [ 31.712948] [fglrx] Reserved FB block: Unshared offset:fc2b000, size:3d5000 [ 31.712950] [fglrx] Reserved FB block: Unshared offset:1fffb000, size:5000 [ 41.312020] eth0: no IPv6 routers present As you can see I get multiple instances of [ 28.856127] ADDRCONF(NETDEV_UP): eth0: link is not ready and then finally it becomes read and I get the message [ 30.478390] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready. I searched askubuntun, ubuntuforum, and the web but couldn't find a solution. Any help would be very much appreciated. Here is the bootchart

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• Automation : Selenium iphone(Mobile) Driver To Capture Network using Xcode iPhone Simulator

  - by Sandeep

  I am using Xcode iPhone(Mobile) simulator to run Selenium iPhone WebDriver Automation scripts for mobile Websites. Is there anyway to capture Network-Traffic on iPhone simulator similar to Selenium RC Network capture or BrowserMob Proxy for Web Driver. Please let me know if you know way to capture Network traffic on iPhone simulator programmatically. I do see some tools like Wireshark or HTTPScoop to capture network traffic but I need in a pro grammatical way to automate. I need this scenario for pixel tracking. Thanks Sandeep

  Read the article

• Simulate Network Presence in dbus

  - by Evans

  Is there a way using Python to simulate the presence of an active network connection using dbus? If I call getstate() on the dbus, I'm able to get the current network state. I want to set the current state to 4 (Connection Present). This is because Network Manager is not able to connect using my modem and I use other tools to connect. Pidgin, Empathy and other software are not able to detect the network.

  Read the article

• Can i upload my apk to SD Card instead of internal storage?

  - by Ahmed Al Khashab

  My APK is big, 70 MB. I don't have any problems when I install it in external storage, but when I upload it to phone before installing, the APK goes to internal storage and my testing phone doesn't have enough space in internal storage and a lot of android phones don't have enough internal space for 70 MB... Can I upload my APK straight to the SD Card instead of internal storage first? upload mean "upload from my eclipse while runnig , or download from market, apk will go to internal storage but i want apk go to external and start install from external"

  Read the article

• Smallest sum of graph weight, where each node are connceted (like a network)

  - by Svisstack

  Hello, What algorithm I can use for problem like this: Have a graph positive weighted, i want to know a smallest possible sum of weights where each node are connected (connected like a network, where each node is a eg. network device). In this network each node can be connected with other node by some other other nodes in way. But all nodes from input graph must be in a network. Any one can help me with this?

  Read the article

• Mapping Drive Error - System Error 1808

  - by Julian Easterling

  A vendor is attempting to map and preserve a network drive using nt authority/system; so it stays persistent when the interactive session of the server is lost. They were able to do this on one server (Windows 2008 R2) but not a second computer (also Windows 2008 R2). D:\PsExec.exe -s cmd.exe PsExec v1.98 - Execute processes remotely Copyright (C) 2001-2010 Mark Russinovich Sysinternals - www.sysinternals.com Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. all rights reserved. C:\Windows\system32>whoami nt authority\system C:\Windows\system32>net use New connections will be remembered. Status Local Remote Network -------------------------------------------------------------------- OK X: \\netapp1\share1 Microsoft Windows Network The command completed successfully. C:\Windows\system32>net use q: \\netapp1\share1 System error 1808 has occurred. The account used is a computer account. Use your global user account or local user account to access this server. C:\Windows\system32> I am unsure on how to set up a "machine account mapping" which will preserve the drive letter of the Netapp path being mapped, so that the service account running a Windows service can continue to access the share after interactive logon has expired on the server. Since they were able to do this on one server but not another, I'm not sure how to troubleshoot the problem? Any suggestions?

  Read the article

• Dell VRTX - slow cluster shared storage

  - by NorbyTheGeek

  I have a brand new Dell VRTX box set up as a Failover Cluster running HA Hyper-V virtual machines. This is my first time setting up clustering, and my first time with one of these boxes, so I'm sure I've missed something. The virtual machines are experiencing high disk latency and bad performance when accessing their VHD(x) files located on a Cluster Shared Volume. The VRTX has 10 x 900 GB 10K SAS drives in RAID 6 configuration, and the VRTX has the redundant Shared PERC 8 controllers. Both blades have full access to the virtual disks. There are two M520 blades installed, each with 128 GB RAM. MPIO is configured for the PERC 8 controllers. Operating system on the blades is Server 2012 (NOT R2). The RAID 6 array is split into a small (8 GB) volume for cluster quorum witness and a large (6.5 TB) volume for a Cluster Shared Volume (mounted on the nodes as C:\ClusterStorage\Volume1) An example of slow disk access: logging into a Server 2012 VM and having Server Manager come up automatically. Disk access goes to 100%, with write speeds at 20 MB or so, read speeds of 500 KB or so, and Average Response Time of over 1000 ms, sometimes spiking at 4000-5000 ms or so. It's the latency that really worries me. Is there something specific I should look at in my configuration? It doesn't seem to matter whether I use VHD or VHDX, dynamic or static.

  Read the article

• Existing open source software for wireless mesh networking?

  - by user70352

  Hello! My goal: Build a wireless mesh network with some ALIX 2D2 (500 MHz AMD Geode LX800 x86 CPU, 256MB RAM, Atheros wireless card) Aside from working like a normal wireless mesh network users should be able to read/write data from/to the ALIX Boxes and the ALIX boxes should be able to process data. Questions: Should I try to flash dd-wrt x86, voyage linux (linux.voyage.hk) or something else? What (open source) software should I look into before I start? Should I use a 'server' for data storage and processing instead of the ALIX boxes? Is it even possible to use the ALIX boxes for routing AND data storage and processing? Final notes: Data can be anything, for example, I want to setup a wireless mesh using the OLSRD protocol so my whole town gets wifi and can access songs on the network. It's not for that, but that's the idea. I'm not afraid of programing, compiling or working with *nix. This is mostly 'for fun' rather than for practicality. Thanks in advance for any feedback.

  Read the article

• "No more threads can be created in the system" in Network and Sharing Center

  - by Zell Faze

  A while back I noticed on one of our laboratory computers (Windows 7, very little extra software installed) that the network connection icon in the system tray would claim that it had no network connection, even though it did. This issue would go away after the computer was rebooted, but would surface again the next time I looked at the computer (a few days later). Upon opening the Network and Sharing Center I am shown an actual error message, but not one that seems to give me a lot of information about what the problem is. In the place of the usual information about network adapters and whether you are connected to the Internet it simply says: "No more threads can be created in the system." The Event Viewer shows hundreds of events from different services also with the same message. "Volume Shadow Copy Service error: Unexpected error calling routine CoCreateInstance. hr = 0x800700a4, No more threads can be created in the system."; "The WinHTTP Web Proxy Auto-Discovery Service service failed to start due to the following error: A thread could not be created for the service."; "The IP Helper service terminated with the following error: No more threads can be created in the system." As far as I can tell, this message seems to mean that there is some sort of resource leak in Windows where something is creating a large number of threads and those threads are not being killed off? I've tried restarting WMI and several services related to networking, without avail. Can anyone provide more information on what "No more threads can be created in the system" might mean and what I might be able to do to fix the issue? Currently the only solution appears to be restarting.

  Read the article

• IIS7 web farm - local or shared content?

  - by rbeier

  We're setting up an IIS7 web farm with two servers. Should each server have its own local copy of the content, or should they pull content directly from a UNC share? What are the pros and cons of each approach? We currently have a single live server WEB1, with content stored locally on a separate partition. A job periodically syncs WEB1 to a standby server WEB2, using robocopy for content and msdeploy for config. If WEB1 goes down, Nagios notifies us, and we manually run a script to move the IP addresses to WEB2's network interface. Both servers are actually VMs running on separate VMWare ESX 4 hosts. The servers are domain-joined. We have around 50-60 live sites on WEB1 - mostly ASP.NET, with a few that are just static HTML. Most are low-traffic "microsites". A few have moderate traffic, but none are massive. We'd like to change this so both WEB1 and WEB2 are actively serving content. This is mainly for reliability - if WEB1 goes down, we don't want to have to manually intervene to fail things over. Spreading the load is also nice, but the load is not high enough right now for us to need this. We're planning to configure our firewall to balance traffic across the two servers. It will detect when a server goes down and will send all the traffic to the remaining live server. We're planning to use sticky sessions for now... eventually we may move to SQL Server session state and stateless load balancing. But we need a way for the servers to share content. We were originally planning to move all the content to a UNC share. Our storage provider says they can set up a highly available SMB share for us. So if we go the UNC route, the storage shouldn't be a single point of failure. But we're wondering about the downsides to this approach: We'll need to change the physical paths for each site and virtual directory. There are also some projects that have absolute paths in their web.config files - we'll have to update those as well. We'll need to create a domain user for the web servers to access the share, and grant that user appropriate permissions. I haven't looked into this yet - I'm not sure if the application pool identity needs to be changed to this user, or if there's another way to tell IIS to use this account when connecting to the share. Sites will no longer be able to access their content if there's ever an Active Directory problem. In general, it just seems a lot more complicated, with more moving parts that could break. Our storage provider would create a volume for us on their redundant SAN. If I understand correctly, this SAN volume would be mounted on a VM running in their redundant VMWare environment; this VM would then expose the SMB share to our web servers. On the other hand, a benefit of the shared content approach is that we'd only need to deploy code to one place, and there would never be a temporary inconsistency between multiple copies of the content. This thread is pretty interesting, though some of these people are working at a much larger scale. I've just been discussing content so far, but we also need to think about configuration. I don't know if we can just use DFS replication for the applicationHost.config and other files, or if it's best to use the shared configuration feature with the config on a UNC share. What do you think? Thanks for your help, Richard

  Read the article

• Accessing network shares on Windows7 via SonicWall VPN client

  - by Jack Lloyd

  I'm running Windows7 x64 (fully patched) and the SonicWall 4.2.6.0305 client (64-bit, claims to support Windows7). I can login to the VPN and access network resources (eg SSH to a machine that lives behind the VPN). However I cannot seem to be able to access shared filesystems. Windows is refusing to do discovery on the VPN network. I suspect part of the problem is Windows persistently considers the VPN connection to be a 'public network'. Normally, you can open the network and sharing center and modify this setting, however it does not give me a choice for the VPN. So I did the expedient thing and turned on file sharing for public networks. I also disabled the Windows firewall for good measure. Still no luck. I can access the server directly by putting \\192.168.1.240 in the taskbar, which brings up the list of shares on the server. However, trying to open any of the shares simply tells me "Windows cannot access \\192.168.1.240\share You do not have permission to access ..."; it never asks for a domain password. I also tried Windows7 native VPN functionality - it couldn't successfully connect to the VPN at all. I suspect this is because SonicWall is using some obnoxious special/undocumented authentication system; I had similar problems trying to connect on Linux with the normal IPsec tools there. What magical invocation or control panel option am I missing that will let this work? Are there any reasonable debugging strategies? I'm feeling quite frustrated at Windows tendency to not give me much useful information that might let me understand what it is trying to do and what is going wrong.

  Read the article

• Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

  - by Casey

  I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

  Read the article

• Intel Wireless 4965AGN not achieving N throughput when connected to an Airport Express N network

  - by BenA

  I have an Intel Wireless WiFi Link 4965AGN adaptor in my laptop (HP Pavillion dv2000 series) which is connecting to a 5Ghz-only 802.11n network provided by an Apple Airport Express. The network is using WPA2 encryption. My desktop is also connected the Airport, via a Linksys WUSB600N USB adaptor. Both are running with the latest drivers, and the Airport is running the latest firmware. The Airport is also configured to use wide channels. The problem I have is that I never get throughput above 4MB/s when transferring files between the two machines. Even a pessimistic calculation shows a 270Mbps network as being capable of transfer rates at well above 10MB/s. I'm pretty sure I've isolated the issue to being the Intel adaptor, as wiring the desktop to the AP, and using the Linksys adaptor on the laptop immediately yielded speeds limited by the 100MB/s ethernet connection. I know that 802.11n is still a draft standard, and so mixing kit from different manufacturers can easily lead to poor results, but I was just wondering if anybody else out there has had success with this Intel adaptor on an N network? Or even better, connecting it to an Airport Express? Can anybody give me any advice on how to troubleshoot this issue? I should also mention that the Airport Express doesn't allow you to manually specify channels when running in N mode, and that I've been able to rule out interference from other Wireless LANs by scanning. There aren't any other 5GHz networks in my area. All ideas welcome! Update: A while later, I've just updated to the most recent drivers for both the Intel chip in the laptop, and the USB adaptor. Unfortunately this hasn't improved things :(. If anybody has any advice it would be be gratefully received.

  Read the article

• Remove Kernel Lock from Unmounted Mass Storage USB Device from the Command Line in Linux

  - by Casey

  I've searched high and low, and can't figure this one out. I have a older Olympus Camera (2001 or so). When I plug in the USB connection, I get the following log output: $ dmesg | grep sd [20047.625076] sd 21:0:0:0: Attached scsi generic sg7 type 0 [20047.627922] sd 21:0:0:0: [sdg] Attached SCSI removable disk Secondly, the drive is not mounted in the FS, but when I run gphoto2 I get the following error: $ gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') *** What command will unmount the drive. For example in Nautilus, I can right click and select "Safely Remove Device". After doing that, the /dev/sg7 and /dev/sdg devices are removed. The output of gphoto2 is then: # gphoto2 --list-config /Camera Configuration/Picture Settings/resolution /Camera Configuration/Picture Settings/shutter /Camera Configuration/Picture Settings/aperture /Camera Configuration/Picture Settings/color /Camera Configuration/Picture Settings/flash /Camera Configuration/Picture Settings/whitebalance /Camera Configuration/Picture Settings/focus-mode /Camera Configuration/Picture Settings/focus-pos /Camera Configuration/Picture Settings/exp /Camera Configuration/Picture Settings/exp-meter /Camera Configuration/Picture Settings/zoom /Camera Configuration/Picture Settings/dzoom /Camera Configuration/Picture Settings/iso /Camera Configuration/Camera Settings/date-time /Camera Configuration/Camera Settings/lcd-mode /Camera Configuration/Camera Settings/lcd-brightness /Camera Configuration/Camera Settings/lcd-auto-shutoff /Camera Configuration/Camera Settings/camera-power-save /Camera Configuration/Camera Settings/host-power-save /Camera Configuration/Camera Settings/timefmt Some things I've tried already are sdparm and sg3_utils, however I am unfamiliar with them, so it's possible I just didn't find the right command. Update 1: # mount | grep sdg # mount | grep sg7 # umount /dev/sg7 umount: /dev/sg7: not mounted # umount /dev/sdg umount: /dev/sdg: not mounted # gphoto2 --list-config *** Error *** An error occurred in the io-library ('Could not lock the device'): Camera is already in use. *** Error (-60: 'Could not lock the device') ***

  Read the article

• Windows 8 unable to connect to WPA2 AES Wireless Network

  - by user170193

  I'm running Windows 8 and am unable to connect to my home wireless network. I've tried restarting the router, patching the drivers to the next version, patching the drivers to the last version, running windows update and patching the chipset drivers to the latest version. So far nothing has worked. My computer can get on the internet via USB tethering on my phone or an open WiFi connection, but it is unable to connect to my home WPA2 AES secured wireless network. It sees the network, attempts to connect, gets a limited connection and then drops the connection. All the other wireless devices in my household have no problems. I have the new Dell XPS 12, running Windows 8 using an Intel Centrino Advanced-N 6235 wireless adapter. I've refreshed windows twice now to try different driver configurations. I've tried uninstalling all the Dell software, I've tried uninstalling all the Intel software and reinstalling just the drivers. I've tried turning switching the ability for the Wireless driver to turn the computer off or on. I've tried setting up the connection manually from desktop mode. I've tried switching it on and off using the wireless button on the keyboard and in the software. So far nothing has allowed me to connect to the secured network. It just keeps getting a limited connection, dropping the connection and retrying. It's driving me crazy, any ideas, anything I missed? Thanks.

  Read the article

• Mac OS/X system sound storage?

  - by bobobobo

  I want to find the system sounds on my Mac. Where are they?

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >