Search Results

Search found 3018 results on 121 pages for 'plug'.

Page 95/121 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

• Hard drive spark, can it be recovered?

  - by user163558

  Alright, so I was going to install Source Film Maker but I didn't have any space, so I decided to connect an HDD via an USB converter(image below). I shut down the machine, turned the PSU off, and connected via a Molex connector & the USB converter. I turned back on the PSU, no sparks or anything, everything normal, but when I turned on the machine, I heard some sizzing(lol?) and sparks flying and a little flame, but the PC was running fine. I pressed the power button instead pulling out the plug (I panicked) so it continued to short circuit for about 10 seconds. There's a very little part on the HDD that become ash, it's near the Molex connector and the circuit is a little black as well. I'm afraid that I will damage the HDD more so I didn't hook up the HDD after all. Do you think it's the PSU(came default with Cooler Master Elite 430, 500W) or it's the HDD(Samsung SP1203N)? P.S: I've attached the HDD same way before(like 3 months ago), and it worked. HDD burn: USB connector: Sorry for the bad image quality, taken with my phone.

  Read the article

• PC can't detect second RAM installed

  - by kulwinder

  I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

  Read the article

• So who decided VGA cables should be symetrical ? [closed]

  - by mgb

  < rant So who decided that VGA cables should be the same gender connector at both ends? I just spent an hour trying to fix a server that would apparently boot but wouldn't display any post messages - I needed to change some bios settings. The monitor gives me a helpful error message - "unable to display this resolution". Wondering how it can't show simple VGA res, I reset the bios, when that doesn't work I remove the BIOS battery. The system is in a rack with a keyboard and monitor mounted 6ft away - with the cable running through the normal waist thick rats nest of wiring of wiring. The monitor worked with another system, so it and the VGA cable are good, I brought in another monitor and tried that - still nothing. Eventually I ripped the rack apart to discover that the other end of the VGA connector I was trying to plug into the server was actually plugged into another server box ! And the second monitor I was testing was plugged into the first monitor. An error message like - "I'm actualy plugged into another monitor stupid" - would be useful. So would having a connector with a male end and a female end. < end rant - thank you

  Read the article

• Find the IP of the router between me and main router/gateway?

  - by Crash893

  I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

  Read the article

• Grub hangs at "Starting up ..." when USB flash card reader is plugged in (on Ubuntu Hardy)

  - by Laurence Gonsalves

  I have a PC with Ubuntu Hardy installed. The machine boots fine unless my USB flash card reader (one of those N-in-1 readers by MediaGear) is plugged in at startup. If the reader is plugged in, the boot process proceeds as normal until it gets to the screen that says "Starting up ...". At that point it just hangs forever. To work around this I currently leave the reader unplugged when booting, and then plug it back in after I see that Ubuntu is actually starting. This is annoying though, especially when I reboot the machine (typically for updates), forget to unplug the reader, and walk away only to come back hours later to find the machine hung. My guess is that the presence of the reader is confusing Grub about where to find the kernel. The weird thing is that Grub is on the same drive as the kernel I want it to boot so clearly the drive is still readable even when the flash card reader is plugged in. Is there some way I can tell Grub to never go looking on the flash card reader?

  Read the article

• Testing realistic loads for new versions of existing web app

  - by David Cournapeau

  Assuming I have a relatively complex web application, I am interested in testing performances of a new version using a traffic as realistic as possible. Traffic is relatively complex (session-based, lots of internal logic which depends on incoming requests). The webapp depends on many servers (databases, frontends, etc...). I can think of two basic directions: Recording every incoming request with its timestamp in production in a centralized manner and replaying it from N clients to reproduce a load as close as possible as the original. Issue: because we have many servers, getting the centralized log is not trivial. having a system duplicating requests to a staging area so that I could "plug" a dev version of my webapp to it at anytime without affecting the production. Issue: I have not found much information about it expect this, which suggests to me that may not be the best solution. OTOH, it is realistic by definition. What is the standard way of doing this kind of testing ? I did not find much information about load testing with complex, realistic traffic.

  Read the article

• No sound through headset - only mic is working

  - by Kristis

  I noticed that no sound is being played to my headphones. The laptop has a conexant sound card together with the sounds apps provided. But the thing is that I also noticed that now instead of one playback device - 2 are presented: speakers and headphones. And while speakers do play sound nicely - even test sound are not played through headphone output. Also, headphone output does not have a jack assigned to it, while speakers have L R Rear panel Analog Jack(my laptop does not have a jack on the back - only on the right). Also - my headphones have a mic as well - and when I plug it in - the mic is working(using top panel digital jack),but the headphones themselves are not. And laptop is recognizing when audio device is plugged in. And I checked the headset on other devices - the headphones are working. I have tried updating drivers, rolling back drivers and completely uninstalling drivers and then restarting - nothing helped. I imagine that I somehow need to reconfigure the jack configuration just have no idea how and where. Any suggestions? Thanks

  Read the article

• ios7 loops on the "trust this computer" dialog

  - by gcb

  trying to transfer files to the work ipad via my debian7 box. When i plug it on the computer usb port, it shows the dialog about trusting this computer, and the computer shows a gnome alert about the ipad being locked and that i should unlock it and try again. i press "trust" on the ipad and try again on gnome. and it starts again. over and over. endlessly. there are dozen threads about this on apple support forums. no solution. just dozens of "me too" flags. e.g. https://discussions.apple.com/message/23082859#23082859 (44 me-too, 2k views) here is the log/messages i get Oct 23 21:17:39 dotmatrix kernel: [ 1928.517766] usb 2-1.7: USB disconnect, device number 16 Oct 23 21:17:39 dotmatrix kernel: [ 1928.715441] usb 2-1.7: new high-speed USB device number 17 using ehci_hcd Oct 23 21:17:40 dotmatrix kernel: [ 1928.811031] usb 2-1.7: New USB device found, idVendor=05ac, idProduct=12ab Oct 23 21:17:40 dotmatrix kernel: [ 1928.811036] usb 2-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Oct 23 21:17:40 dotmatrix kernel: [ 1928.811039] usb 2-1.7: Product: iPad Oct 23 21:17:40 dotmatrix kernel: [ 1928.811041] usb 2-1.7: Manufacturer: Apple Inc. Oct 23 21:17:40 dotmatrix kernel: [ 1928.811043] usb 2-1.7: SerialNumber: fec5e0f6a6fa18a936de3c53af661051d290275e Oct 23 21:17:40 dotmatrix mtp-probe: checking bus 2, device 17: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7" Oct 23 21:17:40 dotmatrix mtp-probe: bus: 2, device: 17 was not an MTP device Oct 23 21:17:43 dotmatrix kernel: [ 1932.346505] usb 2-1.7: USB disconnect, device number 17 If i never press the trust dialog it will stay there until i remove the cable. but the logs shows that it gave up 3sec after the cable was connected.

  Read the article

• Iptables QUEUE Target and Snort

  - by bradlis7

  I'm trying to set up a firewall with support for snort, and it is dropping all of my packets when I add the QUEUE target. I've made it like this, but the QUEUE target is not allowing the packets to be processed any further: -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -j QUEUE -A INPUT -j ACCEPT # It's not allowing anything past QUEUE, as you can see below in the count. > iptables -I INPUT -nv pkts bytes target prot opt in out source destination 6707 395K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 933 138K QUEUE all -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 I'm eventually going to change it to forward, but I'm just trying to get it working for now. I start snort like so: snort -Q -D -c /etc/snort/snort.conf EDIT: More Information When I run it, it still sees the packets without having an iptables QUEUE target rule, but when I add a QUEUE target, it starts losing all of my packets. # snort -Qc /etc/snort/snort.conf -N -A console Enabling inline operation Running in IDS mode --== Initializing Snort ==-- Initializing Output Plugins! Initializing Preprocessors! Initializing Plug-ins! Parsing Rules file "/etc/snort/snort.conf" ## === CUT === *** *** interface device lookup found: bond0 *** Initializing Network Interface bond0 Decoding Ethernet on interface bond0 ## === CUT === Not Using PCAP_FRAMES So, it says inline, but the it says it's using bond0. Inline should not require an interface, right?

  Read the article

• Possible boot conflict?

  - by Evan Kroske

  I was installing Ubuntu on a computer on which Windows XP was already installed. The computer has multiple hard drive bays, so I decided to remove the XP HDD and install Ubuntu on a blank HDD when it was the only HDD in the system. Unfortunately, if I now try to boot Ubuntu with the Windows XP drive in the second slot, nothing will boot. However, if Windows XP is in the first slot, it will boot fine. Can anybody explain why this happens? When I was checking out the BIOS to see if something was messed up, I discovered that when Ubuntu is in the first slot, the BIOS doesn't recognize any HDDs. However, if XP is in the first slot, the BIOS recognizes both drives. Any hypotheses about why this happens? Edit: Here's the setup. I have an old server with seven SCSI HDD slots. I have five identical 68 Gb SCSI drives, but I can keep only two plugged in. XP is still installed on the first drive, but I reinstalled Ubuntu on the second drive and had Grub overwrite the XP bootloader on the first drive. Now, the setup works fine, and I can use Grub to load either XP or Ubuntu. However, if I plug in another identical blank HDD in the third slot, the computer recognizes only the XP drive and doesn't boot. Grub starts to load, then gives me a "disk not found" error. Running ls from the grub rescue prompt only shows one drive with two partitions. I guess this is a BIOS problem, but I'd still like to know what triggers it. What about a blank drive could cause the BIOS to freak out?

  Read the article

• Wireless connection drops when wired computer starts a game.

  - by Skadlig

  Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

  Read the article

• How to route public static IP to a virtual machine on a vmware ESXi host?

  - by Kevin Southworth

  I have 5 static IPs from my ISP (Comcast) and I have a physical machine with VMware ESXi 4.0 on it that is hosting multiple virtual machines. Right now I am just using the default vmware virtual network (vswitch0) with DHCP from the Comcast IP Gateway Router and everything is working fine. Each virtual machine can access the internet, etc. One of my virtual machines is a webserver (Windows Server 2008) and I want to assign it to 1 of my 5 static IPs so it's accessible from the public internet, while leaving the other VMs on the internal LAN still using DHCP. If I just plug my laptop directly into the Comcast IP Gateway (it has 4 ports on the back) and assign my laptop a Static IP using the windows networking dialogs, then I can hit my laptop from the public internet and it works great. However, if I try to do the same steps to set a static IP config on my Windows Server 2008 VM, it does not work. The VM cannot access the internet (open Firefox and try to visit google.com), and I cannnot see the VM from the public internet either. I'm assuming I'm missing something in the ESXi config somewhere, but I'm pretty new to ESXi and I'm not sure how to configure it to work this way.

  Read the article

• fedora, dhcpd fails to start

  - by soxs060389

  History: I got a tiny shiny plugserver which I want to plug to my ADSL router (or however you want to call it) on one end (eth0), and the other end (eth1) I want to run a dhcp server for my LAN. ATM I am stuck with getting LAN to work. OS is fedora 12. I configured my /etc/dhcp/dhcpd.conf like this: # # DHCP Server Configuration file. # see /usr/share/doc/dhcp*/dhcpd.conf.sample # see 'man 5 dhcpd.conf' # option domain-name "unknown.org"; option domain-name-servers 192.168.44.1; option subnet-mask 255.255.255.0; option broadcast-address 192.168.44.255; default-lease-time 86400; max-lease-time 172800; subnet 192.168.44.0 netmask 255.255.255.0 { host fedorabigbox { hardware ethernet 00:19:66:8E:61:74; fixed-address 192.168.44.21; } #host mobile #{ # hardware ethernet ***; # fixed-address 192.168.44.22; #} range 192.168.44.100 192.168.44.110; option routers 192.168.44.1; } # this is just dummy, as read many howtos, some suggesting to add a subnet blah netmask blah for each interface subnet 192.168.33.0 netmask 255.255.255.0 { range 192.168.33.100 192.168.33.110; option routers 192.168.33.1; } But the server fails to start when trying to start it via /etc/init.d/dhcpd start In general it would be nice if someone can point me to a in detail explanation of how network works, I am pretty new to this stuff. More concrete question: How to point the subnets to eth1 and the other to eth0, how can this be achieved? Does someone see any errors or flaws? Syntax should be correct, allready checked that with the dhcpd syntax check. Thanks for any help

  Read the article

• Windows 7 Cable Connection Rehabilitation

  - by Giovanni De Gaetano

  I recently switched the operating system of my laptop from Windows XP to Windows 7. My web-connection is such that I need to identify everytime before connecting. Since there is no automatic identification request, while using Windows XP I was used to de-abilitate and rehabilitate the cable connection after every switching on. I successfully installed the web-connection on Windows 7, and later on I switched the computer off and on (simply because I had to sleep!). After restarting the computer, since there was no automatic identification request, I de-abilitate the cable connection. But this time I didn't find any way to rehabilitate it! Do you have any suggestions on how to solve the problem? My "Wired AutoConfiguration" has the startup type "Automatic", but it's not enough to restart automatically the cable connection! I tried to do some standard things like restart the computer, unplug and plug in again the cable, reinstall the web-connection from the scratch... But nothing worked! Thank you very much for your help!

  Read the article

• Asus K55VM usb 3.0 issue

  - by user2141481

  Good day superusers! I own the above laptop and I found out that there are some unknown and unusual issues with usb 3.0 ports. I haven't noticed anything strange until now. I got a new toshiba usb 3.0 external hdd and when I try to copy larger amount of data from my disk to the external hdd, the OS(windows 7) randomly starts ignoring the external hdd. It doesn't shut it down, it kinda just stops responding but the light on the hdd is still lit. I get an error that the files cannot be copied. I have reinstalled windows 7, installed all drivers(including intel chipset drivers of course) and the issue is still present. It acts normal when copying small amount of data. Also, I heard that some intel chipsets have an issue with usb, something about the connectors not transferring power when the usb device enters some kind of "low power mode" causing the device to stop responding and you need to plug it out and in again. But the thing is, my Intel® Chief River Chipset HM76 is not on the list of affected hardware(not ENTIRELY sure though). If anyone has any idea of what the problem to this might be, I'd be greatful. Edit: The hdd works perfectly fine even for large amounts of data if plugged in the usb 2.0 port!

  Read the article

• MicroSD card getting corrupted for no good reason

  - by ChaosR

  I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here? EDIT: It seems I can't even put ext3 or ext4 on it, they both complain about a corrupted journal. Gheh, guess something is really broken here.

  Read the article

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• How does USB device recognition work?

  - by GorillaSandwich

  I'm curious how USB device recognition works in Windows. I imagine it's something like this: When you plug in a device, it tells Windows "here's my device ID to tell you what I am" Windows looks to see if any drivers have been installed that match that device ID. The driver probably tells Windows what the device should be called - like "BlackBerry Curve" or "Canon Printer" If so, it somehow associates that device with that driver Otherwise, it looks for a matching driver online (if you let it) Am I right? If so, that still leaves some questions. When you install drivers, where do they go? Are they files in a folder, or do they get added to the registry? What is Windows doing when it first recognizes the device, thinks, and finally says "your new device is installed and ready to use?" Where does Windows look for missing drivers? Is it in their own database? Do device manufacturers submit drivers to Microsoft for inclusion there? Can anybody explain how this process really works? Also, do other OSes do this differently?

  Read the article

• Router block some sites

  - by Mahesha999

  Hi I was using ADSL Modem/Router earlier. The device is quite old Pronet PN-ADSL 101 E/U model (pics: http://bit.ly/P2YaWy, http://bit.ly/OA700l) Since it had only one RJ45 out, I bought new Wireless Router TPLink TL-WR941ND. It has 4 RJ45 out and 3 wireless antennas. I configured my old router in bridge. Now, if I have to connect my pc to Internet through the old router, I have to enter username and password. Then I connected the RJ45 output of old router to the WAN in of new router. and ran the CD of new router. It configured the new router in PPPoE by saving the username and password in router to dial automatically. So now I have to just plug in the wires in my new routers any RJ45 out. I am able to access the Internet when I connect through new router (both wired and wirelessly), but some sites are getting blocked. Most notably yahoo.com (though ymail.com is working), Microsoft.com. msn.com. These sites work perfectly fine when I connect my pc directly to my old router and enter username and password manually. (However others like google.com. facebook.com works fine when connect through new router) So here these some sites need some parameter set but I am unable to find them out. Can anyone help me. My friend said he also faced same problem. Surprisingly he advised me to see if the same websites will work through Opera turbo mode and boom they worked. So what could be the problem?

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• Getting Dell E6320 with I7 to work with 3 monitors at 1920x1080p x 3

  - by MadBoy

  I want to buy Dell E6320 which comes with Intel Core I7-2620M (2.70GHz, 4MB cache, Dual Core) with Intel HD Graphics 3000. Laptop will come with docking station. I want to connect 3 monitors to that docking station so that working at home would give me some additional boost. Docking station will allow me to connect only 2 monitors so I'm looking at following other options: Matrox TRIPLEHEAD2GO DIGITAL Edition or TRIPLEHEAD2GO DP Edition. But reading Matrox Support Page intel GPU can't run the highest resolution with 3 monitors connected, it even gets worse since it seems monitors would have to be able to work at 50hz. Also I'm not sure but it seems that Matrox doesn't split the monitors as 3 separate monitors but simply as one big space (which is a bit opposite to what I need) Buy 2 or maybe just 1 USB based monitor but it would also mean having 1 or 2 different monitors then the main one, unless I buy 3 USB based monitors which would mean more money to spend. Also I found only couple of models and most of them require USB 3.0 and no other cables to plug in (nice but costly - couldn't find decent monitor with only USB for sending signal and having power connected normally) . But docking station has only one USB 3.0 port. Can I use hub and still get it to work? Find some converters from Digital to USB (I think DisplayLink does some?) Buy different laptop but what kind? I need it to be I7, small (13"), fast and lightweight. At same time it requires docking station that I can use at home to connect 3 external monitors. Some other suggested solution... Edit: I need 3 monitors for work in terms of coding in Visual Studio or having word/excel/outlook open. Nothing fancy. Maybe some movie once in a while.

  Read the article

• Laptop battery holds charge, but won't charge any more.

  - by Jeff

  Ok, I'm sure I will need to replace either my battery or my AC adapter, but would rather not buy one if the other is the problem. My problem is. I have a Sager laptop that gets quite a bit of use. The charging has always been a little bit odd. If I was in the process of using it, it would charge just fine and stay On AC power. If I left it alone, however(power settings to ONLY turn off the monitor) in either Ubuntu or Windows 7 it decides that it didn't want to use AC power anymore and would just start draining the battery until it died. Now, suddenly, it won't charge at all. The capacity was great up to this point which happened in an instant. It will recognize the battery but won't see the AC power if plugged in while the battery is in. I can power up the laptop without the battery and it works fine. If I plug in the battery while powered up it will claim it's charging it, but it stays at the same percentage. If I unplug the power, it will switch over to Battery fine, but I have to power down and unplug the battery to get it back on AC power. I've had dying/dead batteries before but they typically won't hold a full charge anymore but it still winds up to 100% then drops quickly when unplugged. This seems more like a chip problem in the battery to me, but I'm not sure. Any ideas?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Compaq motherboard CQ60 AMD - nvidia chipsed graphic problem

  - by Dritan

  Hi! It nice to have read that you solved this problem this way. I have 2 laptops Compaq CQ60 AMD Athlon with Nvidia graphic cards. the first one is new, when i press power button, it lights up only the ON led in front and nothing else, no fan working, blank screen, no beep.. I don't know what may be the problem. When I put on power adaptor, it lights up only the side power led near dhe power adapter plug but it doesn't light up the front led one. the second one have this problem that it spins the fan, light power and On led, but it doesn't show nothing on the screen blank (even with external monitor). In this case it maybe this problem of the Nvida Graphic Chip and it may need a reflow. I have an hot air station, but I don't know if I should try this or the oven one. Please can you give me any suggestion what to do to solve this. I have read that the solution of the Oven method is just temporary,maximum of three months, do you have the same experience about this? Any suggestion is wellcome.

  Read the article

• Free software for backing up an attached network drive

  - by Richard

  My wireless router comes with a USB connector which allows me to plug an external hard drive in and it'll act as a Network Attached Storage. The problem is that I want to backup this hard-drive to the external drive of another computer so that if the NAS drive fails, I don't lose everything. However, Windows 7 Backup refuses to include the NAS as a location to backup. I can't fool it by mapping it to a drive letter either. Google presents lots of pages on how to backup files to a NAS, but not the other way around. Can anyone advise me on free software which can do incremental backups of a NAS drive to an external drive attached the computer it is running on? I'm aware of this question but the top answers have one or more of the following issues: They aren't free. The free version cannot backup a NAS. They cannot do incremental backups. They're just a script and therefore have limited other functionality (eg. disk space management, scheduling, compression, etc.etc.)

  Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >