Search Results

Search found 5579 results on 224 pages for 'soft keyboard'.

Page 96/224 | < Previous Page | 92 93 94 95 96 97 98 99 100 101 102 103  | Next Page >

  • Wubi installation: I get os freezes which make me have to hard reboot

    - by user54774
    Wubi installation has been going a success for me, but one problem is that I get freezes, My Mouse works I can move it round but I can't click or right click. Sometimes my keyboard works and so I can shutdown safely using commands, but other times the keyboard doesn't work. One example of this is when I was running minecraft and youtube. and to off the laptop the only way was to hard reboot. Does anyone have a solution to this?

    Read the article

  • wireless internet in linux is very very slow... but in windows.... everythnings fine

    - by Cody Acer
    yesterday when i was connecting to our neighbors wifi connection which is the signal strength is below 50%, i cant browse anything... even ping to gateway. 100% packet loss, and sometimes.. i can connect awesomely i can open my facebook account for 15 minutes but after 15min.. connection is extremely slow. but not windows i can surf even the signal str is very poor weird ey??.. root@Emely:~# lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] 00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 3 [8086:27d4] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: lpc_ich Kernel modules: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel modules: i2c-i801 05:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: bcma-pci-bridge Kernel modules: bcma 09:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] Subsystem: Samsung Electronics Co Ltd Notebook N150P [144d:c072] Kernel driver in use: sky2 Kernel modules: sky2 root@Emely:~# ip addr show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff inet 192.168.1.108/24 brd 192.168.1.255 scope global wlan0 inet6 fe80::21b:b1ff:fea9:ace0/64 scope link valid_lft forever preferred_lft forever root@Emely:~# ip link show 1: lo: mtu 65536 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether e8:11:32:2e:a6:fd brd ff:ff:ff:ff:ff:ff 3: wlan0: mtu 1500 qdisc mq state UP qlen 1000 link/ether 00:1b:b1:a9:ac:e0 brd ff:ff:ff:ff:ff:ff root@Emely:~# rfkill list all 0: samsung-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: samsung-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: no Hard blocked: no is this a wireless driver issue?

    Read the article

  • How to get german QWERTY on Windows?

    - by Arturas M
    Well I'm used to having the world standard keyboard which is qwerty and not qwertz... But on windows I can't find the choice for german input which would be qwerty, not qwertz. In linux there was german input with qwerty so it was fun. I believe it should be on Windows too? Cause i'm sick of this qwertz always having to correct and search for z or y... Yeah, I know, if Germans made a mistake, it wasn't loosing WW2... Edit: Maybe I wasn't clear enough, it's not about changing between different language inputs? It's about having all german keys in german input, just the z and y would be in the correct places like all the worlds keyboards use and like the US keyboard uses... Solution: Well unfortunately by searching everywhere and waiting for answers I couldn't find what I needed, so I came up with this solution - I used The The Microsoft Keyboard Layout Creator And created my own very custom layout by modifying the default german layout and switching places of z and y. In case somebody needs it and doesn't want to go the hard way, I decided to upload them, so here are the links to download and install the keyboard layout: http://www20.zippyshare.com/v/95071447/file.html http://rapidshare.com/files/3822150342/German%20QWERTY%202%20by%20Arturas%20M.zip It will appear as a choice under German input between languages in your language bar. If you just want to use this german layout, just remove all german layouts and install this one. Good luck and have fun using it!

    Read the article

  • SSH into remote server using Public-private keys

    - by maria
    Hi, I have recently setup ssh on two linux machines (lets call them server-a, client-b). I have generated two ssh auth files on client-b machine using ssh key gen and can see both public and private files in .ssh dir. I have named them 'example' and 'example.pub'. Then I have added example.pub to sever-a's auth file. When I try to ssh into server-a it still requests a password authentication where as I want a password less login (private key on client-b is setup without password). When I try to ssh with '-v' .. get the following output: debug1: Next authentication method: publickey debug1: Trying private key: /Users/abc/.ssh/identity debug1: Offering public key: /Users/abc/.ssh/id_rsa debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering public key: /Users/abc/.ssh/id_dsa debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,keyboard-interactive debug2: we did not send a packet, disable method debug1: Next authentication method: keyboard-interactive debug2: userauth_kbdint debug2: we sent a keyboard-interactive packet, wait for reply debug2: input_userauth_info_req debug2: input_userauth_info_req: num_prompts 1 Password: Please help.

    Read the article

  • Apple: Bind a key to a commandline command?

    - by Stefan Lasiewski
    I have a Mac Powerbook running Leopard (10.5.8). Does Leopard provide an easy way to bind keys to commands which are typically run on the commandline? For example, I can open up Terminal.app and run the command /System/Library/Frameworks/ScreenSaver.framework/Resources/ScreenSaverEngine.app/Contents/MacOS/ScreenSaverEngine which will activate the screensaver and lock my screen. What if I want to bind 'Apple-key L' to this command and execute this globally, regardless of which application is in use at the moment? Can I do this, or can I only run ScreenSaverEngine from a Terminal window? I tried to set up global keyboard shortcuts, but it seems that this won't allow me to bind a key to an arbitrary shell command: Note: You can create keyboard shortcuts only for existing menu commands. You cannot define keyboard shortcuts for general purpose tasks such as opening an application or switching between applications. I tried to set up a application keyboard shortcut, but commands like ScreenSaverEngine don't seem to be an application. Note that this Screensaver/Lock screen is just one example. I have come across other nifty commands which I might want to bind to a key-combination as well. I can do this in Gnome and Windows (with varying success). How about with Leopard?

    Read the article

  • Windows 7 ignores F6/F8 and will not boot

    - by P.Brian.Mackey
    I have a work PC with sophos safeguard encryption on it. Windows failed to start. When I bootup I receive an error saying a recent hardware or software change might be the cause. File: \Boot\BCD Status: 0xc0000098 Info: The windows boot configuration data file does not contain a valid OS entry. This began after the PC forced me to run a system recovery. My machine had powered down improperly (power outage?) and simply would not respond to my keyboard input to cancel the option to scan my system. After the scan "repaired" a boot file, my system crashed. Now it tells me I can insert my windows 7 disk and run recovery. I can't simply do this because of Safeguard. The system recovery can't see my encrypted drive. I tried hitting F2 to manually login to Safeguard and then selected the option to boot from media. The computer prompts me to hit any key to boot from disk...which I do, but once again it is not reading my keyboard input. I can't get F8/F6 to bypass startup files and get me to a command prompt like the old days. If I could get to a command prompt I might could recover the file windows jacked up from its backup location...though I may need to use the windows recovery disk UI to do this..??? In the past I've been able to slap in a PS/2 keyboard when the USB keyboards stop responding like this. I have no PS/2 keyboard available. Anyone have any idea how I can undo the damage windows system recovery has done with safeguard installed?

    Read the article

  • Password-less login into localhost

    - by Brad
    I am trying to setup password-less login into my localhost because it's required for a tutorial. I went through the normal steps of generating an rsa key and appending the public key to authorized_keys but I am still prompted for a password. I've also enabled RSAAuthentication and PubKeyAuthentication in /etc/ssh_config. Following other suggestions I've seen, I tried: chmod go-w ~/ chmod 700 ~/.ssh chmod 600 ~/.ssh/authorized_keys But the problem persists. Here is the output from ssh -v localhost: (tutorial)bnels21-2:tutorial bnels21$ ssh -v localhost OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to localhost [::1] port 22. debug1: Connection established. debug1: identity file /Users/bnels21/.ssh/id_rsa type 1 debug1: identity file /Users/bnels21/.ssh/id_rsa-cert type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa type -1 debug1: identity file /Users/bnels21/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 1c:31:0e:56:93:45:dc:f0:77:6c:bd:90:27:3b:c6:43 debug1: Host 'localhost' is known and matches the RSA host key. debug1: Found key in /Users/bnels21/.ssh/known_hosts:11 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/bnels21/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Offering RSA public key: id_rsa3 debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /Users/bnels21/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Any suggestions? I'm running OSX 10.8.

    Read the article

  • SSH Keys Authentication keeps asking for password

    - by Rhyuk
    Im trying to set access from ServerA(SunOS) to ServerB(Some custom Linux with Keyboard Interactive login) with SSH Keys. As a proof of concept I was able to do it between 2 virtual machines. Now in my real life scenario it isnt working. I created the keys in ServerA, copied them to ServerB, chmod'd .ssh folders to 700 on both ServerA,B. Here is the log of what I get. debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: Peer sent proposed langtags, ctos: debug1: Peer sent proposed langtags, stoc: debug1: We proposed langtags, ctos: en-US debug1: We proposed langtags, stoc: en-US debug1: SSH2_MSG_KEX_DH_GEX_REQUEST sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: dh_gen_key: priv key bits set: 125/256 debug1: bits set: 1039/2048 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'XXX.XXX.XXX.XXX' is known and matches the RSA host key. debug1: Found key in /XXX/.ssh/known_hosts:1 debug1: bits set: 1061/2048 debug1: ssh_rsa_verify: signature correct debug1: newkeys: mode 1 debug1: set_newkeys: setting new keys for 'out' mode debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: newkeys: mode 0 debug1: set_newkeys: setting new keys for 'in' mode debug1: SSH2_MSG_NEWKEYS received debug1: done: ssh_kex2. debug1: send SSH2_MSG_SERVICE_REQUEST debug1: got SSH2_MSG_SERVICE_ACCEPT debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /XXXX/.ssh/identity debug1: Trying public key: /xxx/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /xxx/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive Password: Password: ServerB has pretty limited actions since its a custom propietary linux. What could be happening? EDIT WITH ANSWER: Problem was that I didnt have those settings enabled in the sshd_config (Refer to accepted answer) AND that while pasting the key from ServerA to ServerB it would interpret the key as 3 separate lines. What I did was, in case you cant use ssh-copy-id like I couldnt. Paste the first line of your key in your "ServerB" authorized_keys file WITHOUT the last 2 characters, then type yourself the missing characters from line 1 and the first one from line 2, this will prevent adding a "new line" between the first and second line of the key. Repeat with the 3d line.

    Read the article

  • car race game collision condition.

    - by ashok patidar
    in this how can rotate car when it goes to collied with the track side. package { import flash.display.MovieClip; import flash.events.Event; import flash.events.KeyboardEvent; import flash.text.TextField; import flash.ui.Keyboard; import Math; /** * ... * @author Ashok */ public class F1race extends MovieClip { public var increment:Number = 0; //amount the car moves each frame public var posNeg:Number = 1; public var acceleration:Number = .05; //acceleration of the car, or the amount increment gets increased by. public var speed:Number = 0; //the speed of the car that will be displayed on screen public var maxSpeed:Number = 100; public var keyLeftPressed:Boolean; public var keyRightPressed:Boolean; public var keyUpPressed:Boolean; public var keyDownPressed:Boolean; public var spedometer:TextField = new TextField(); public var carRotation:Number ; public var txt_hit:TextField = new TextField(); public function F1race() { carRotation = carMC.rotation; trace(carMC.rotation); //addChild(spedometer); //spedometer.x = 0; //spedometer.y = 0; addChild(txt_hit); txt_hit.x = 0; txt_hit.y = 100; //rotation of the car addEventListener(Event.ENTER_FRAME, onEnterFrameFunction); stage.addEventListener(KeyboardEvent.KEY_DOWN, keyPressed,false); stage.addEventListener(KeyboardEvent.KEY_UP, keyReleased,false); carMC.addEventListener(Event.ENTER_FRAME, carOver_road) } public function carOver_road(event:Event):void { //trace(texture.hitTestPoint(carMC.x,carMC.y,true),"--"); /* if(!texture.hitTestPoint(carMC.x,carMC.y,true)) { txt_hit.text = "WRONG WAY"; if(increment!=0) { increment=1; } } else { txt_hit.text = ""; //increment++; }*/ if (roadless.hitTestPoint(carMC.x - carMC.width / 2, carMC.y,true)) { trace("left Hit" + carMC.rotation); //acceleration = .005; //if(carMC.rotation>90 || carMC.rotation>90 //carMC.rotation += 2; if ((carMC.rotation >= 90) && (carMC.rotation <= 180)) { carMC.rotation += 3; carMC.x += 3; } if ((carMC.rotation <= -90) && (carMC.rotation >= -180)) { carMC.rotation += 3; texture.y -= 3; } if ((carMC.rotation > -90) && (carMC.rotation <= -1)) { carMC.rotation += 3; texture.y -= 3; } if(increment<0) { increment += 1.5 * acceleration; } if(increment>0) { increment -= 1.5 * acceleration; } } if (roadless.hitTestPoint(carMC.x + carMC.width / 2, carMC.y,true)) { trace("left right"); //carMC.rotation -= 2; if(increment<0) { increment += 1.5 * acceleration; } if(increment>0) { increment -= 1.5 * acceleration; } } if (roadless.hitTestPoint(carMC.x, carMC.y- carMC.height / 2,true)) { trace("left right"); //carMC.rotation -= 2; if(increment<0) { increment += 1.5 * acceleration; } if(increment>0) { increment -= 1.5 * acceleration; } } if (roadless.hitTestPoint(carMC.x, carMC.y+ carMC.height / 2,true)) { trace("left right"); //carMC.rotation -= 2; if(increment<0) { increment += 1.5 * acceleration; } if(increment>0) { increment -= 1.5 * acceleration; } } if ((!roadless.hitTestPoint(carMC.x - carMC.width / 2, carMC.y, true)) && (!roadless.hitTestPoint(carMC.x, carMC.y- carMC.height / 2,true)) && (!roadless.hitTestPoint(carMC.x, carMC.y+ carMC.height / 2,true)) && (!roadless.hitTestPoint(carMC.x, carMC.y+ carMC.height / 2,true))) { //acceleration = .05; } } public function onEnterFrameFunction(events:Event):void { speed = Math.round((increment) * 5); spedometer.text = String(speed); if ((carMC.rotation < 180)&&(carMC.rotation >= 0)){ carRotation = carMC.rotation; posNeg = 1; } if ((carMC.rotation < 0)&&(carMC.rotation > -180)){ carRotation = -1 * carMC.rotation; posNeg = -1; } if (keyRightPressed) { carMC.rotation += .5 * increment; carMC.LWheel.rotation = 8; carMC.RWheel.rotation = 8; steering.gotoAndStop(2); } if (keyLeftPressed) { carMC.rotation -= .5 * increment; carMC.LWheel.rotation = -8; carMC.RWheel.rotation = -8; steering.gotoAndStop(3); } if (keyDownPressed) { steering.gotoAndStop(1); carMC.LWheel.rotation = 0; carMC.RWheel.rotation = 0; increment -= 0.5 * acceleration; texture.y -= ((90 - carRotation) / 90) * increment; roadless.y = texture.y; if (((carMC.rotation > 90)&&(carMC.rotation < 180))||((carMC.rotation < -90)&&(carMC.rotation > -180))) { texture.x += posNeg * (((((1 - (carRotation / 360)) * 360) - 180) / 90) * increment); roadless.x = texture.x; } if (((carMC.rotation <= 90)&&(carMC.rotation > 0))||((carMC.rotation >= -90)&&(carMC.rotation < -1))) { texture.x += posNeg * ((carRotation) / 90) * increment; roadless.x = texture.x; } increment -= 1 * acceleration; if ((Math.abs(speed)) < (Math.abs(maxSpeed))) { increment += acceleration; } if ((Math.abs(speed)) == (Math.abs(maxSpeed))) { trace("hello"); } } if (keyUpPressed) { steering.gotoAndStop(1); carMC.LWheel.rotation = 0; carMC.RWheel.rotation = 0; //trace(carMC.rotation); texture.y -= ((90 - carRotation) / 90) * increment; roadless.y = texture.y; if (((carMC.rotation > 90)&&(carMC.rotation < 180))||((carMC.rotation < -90)&&(carMC.rotation > -180))) { texture.x += posNeg * (((((1 - (carRotation / 360)) * 360) - 180) / 90) * increment); roadless.x = texture.x; } if (((carMC.rotation <= 90)&&(carMC.rotation > 0))||((carMC.rotation >= -90)&&(carMC.rotation < -1))) { texture.x += posNeg * ((carRotation) / 90) * increment; roadless.x = texture.x; } increment += 1 * acceleration; if ((Math.abs(speed)) < (Math.abs(maxSpeed))) { increment += acceleration; } } if ((!keyUpPressed) && (!keyDownPressed)){ /*if (increment > 0 && (!keyUpPressed)&& (!keyDownPressed)) { //texture.y -= ((90-carRotation)/90)*increment; increment -= 1.5 * acceleration; } if((increment==0)&&(!keyUpPressed)&& (!keyDownPressed)) { increment = 0; } if((increment<0)&&(!keyUpPressed)&& (!keyDownPressed)) { increment += 1.5 * acceleration; }*/ if (increment > 0) { increment -= 1.5 * acceleration; texture.y -= ((90 - carRotation) / 90) * increment; roadless.y = texture.y; if (((carMC.rotation > 90)&&(carMC.rotation < 180))||((carMC.rotation < -90)&&(carMC.rotation > -180))) { texture.x += posNeg * (((((1 - (carRotation / 360)) * 360) - 180) / 90) * increment); roadless.x = texture.x; } if (((carMC.rotation <= 90)&&(carMC.rotation > 0))||((carMC.rotation >= -90)&&(carMC.rotation < -1))) { texture.x += posNeg * ((carRotation) / 90) * increment; roadless.x = texture.x; } } if (increment == 0) { increment = 0; } if (increment < 0) { increment += 1.5 * acceleration; texture.y -= ((90 - carRotation) / 90) * increment; roadless.y = texture.y; if (((carMC.rotation > 90)&&(carMC.rotation < 180))||((carMC.rotation < -90)&&(carMC.rotation > -180))) { texture.x += posNeg * (((((1 - (carRotation / 360)) * 360) - 180) / 90) * increment); roadless.x = texture.x; } if (((carMC.rotation <= 90)&&(carMC.rotation > 0))||((carMC.rotation >= -90)&&(carMC.rotation < -1))) { texture.x += posNeg * ((carRotation) / 90) * increment; roadless.x = texture.x; } } } } public function keyPressed(event:KeyboardEvent):void { trace("keyPressed"); if (event.keyCode == Keyboard.LEFT) { keyLeftPressed = true; } if (event.keyCode == Keyboard.RIGHT) { keyRightPressed = true; } if (event.keyCode == Keyboard.UP) { keyUpPressed = true; } if (event.keyCode == Keyboard.DOWN) { keyDownPressed = true; } } public function keyReleased(event:KeyboardEvent):void { trace("keyReleased..."); //increment -= 1.5 * acceleration; //increment--; if (event.keyCode == Keyboard.LEFT) { keyLeftPressed = false; } if (event.keyCode == Keyboard.RIGHT) { keyRightPressed = false; } if (event.keyCode == Keyboard.UP) { keyUpPressed = false; } if (event.keyCode == Keyboard.DOWN) { keyDownPressed = false; } } } }

    Read the article

  • Ingame menu is not working correctly

    - by Johnny
    The ingame menu opens when the player presses Escape during the main game. If the player presses Y in the ingame menu, the game switches to the main menu. Up to here, everything works. But: On the other hand, if the player presses N in the ingame menu, the game should switch back to the main game(should resume the main game). But that doesn't work. The game just rests in the ingame menu if the player presses N. I set a breakpoint in this line of the Ingamemenu class: KeyboardState kbState = Keyboard.GetState(); CurrentSate/currentGameState and LastState/lastGameState have the same state: IngamemenuState. But LastState/lastGameState should not have the same state than CurrentSate/currentGameState. What is wrong? Why is the ingame menu not working correctly? public class Game1 : Microsoft.Xna.Framework.Game { GraphicsDeviceManager graphics; SpriteBatch spriteBatch; IState lastState, currentState; public enum GameStates { IntroState = 0, MenuState = 1, MaingameState = 2, IngamemenuState = 3 } public void ChangeGameState(GameStates newState) { lastGameState = currentGameState; lastState = currentState; switch (newState) { case GameStates.IntroState: currentState = new Intro(this); currentGameState = GameStates.IntroState; break; case GameStates.MenuState: currentState = new Menu(this); currentGameState = GameStates.MenuState; break; case GameStates.MaingameState: currentState = new Maingame(this); currentGameState = GameStates.MaingameState; break; case GameStates.IngamemenuState: currentState = new Ingamemenu(this); currentGameState = GameStates.IngamemenuState; break; } currentState.Load(Content); } public void ChangeCurrentToLastGameState() { currentGameState = lastGameState; currentState = lastState; } public GameStates CurrentState { get { return currentGameState; } set { currentGameState = value; } } public GameStates LastState { get { return lastGameState; } set { lastGameState = value; } } private GameStates currentGameState = GameStates.IntroState; private GameStates lastGameState; public Game1() { graphics = new GraphicsDeviceManager(this); Content.RootDirectory = "Content"; } protected override void Initialize() { ChangeGameState(GameStates.IntroState); base.Initialize(); } protected override void LoadContent() { spriteBatch = new SpriteBatch(GraphicsDevice); currentState.Load(Content); } protected override void Update(GameTime gameTime) { currentState.Update(gameTime); if ((lastGameState == GameStates.MaingameState) && (currentGameState == GameStates.IngamemenuState)) { lastState.Update(gameTime); } base.Update(gameTime); } protected override void Draw(GameTime gameTime) { GraphicsDevice.Clear(Color.CornflowerBlue); spriteBatch.Begin(); if ((lastGameState == GameStates.MaingameState) && (currentGameState == GameStates.IngamemenuState)) { lastState.Render(spriteBatch); } currentState.Render(spriteBatch); spriteBatch.End(); base.Draw(gameTime); } } public interface IState { void Load(ContentManager content); void Update(GameTime gametime); void Render(SpriteBatch batch); } public class Intro : IState { Texture2D Titelbildschirm; private Game1 game1; public Intro(Game1 game) { game1 = game; } public void Load(ContentManager content) { Titelbildschirm = content.Load<Texture2D>("gruft"); } public void Update(GameTime gametime) { KeyboardState kbState = Keyboard.GetState(); if (kbState.IsKeyDown(Keys.Space)) game1.ChangeGameState(Game1.GameStates.MenuState); } public void Render(SpriteBatch batch) { batch.Draw(Titelbildschirm, new Rectangle(0, 0, 1280, 720), Color.White); } } public class Menu:IState { Texture2D Choosescreen; private Game1 game1; public Menu(Game1 game) { game1 = game; } public void Load(ContentManager content) { Choosescreen = content.Load<Texture2D>("menubild"); } public void Update(GameTime gametime) { KeyboardState kbState = Keyboard.GetState(); if (kbState.IsKeyDown(Keys.Enter)) game1.ChangeGameState(Game1.GameStates.MaingameState); if (kbState.IsKeyDown(Keys.Escape)) game1.Exit(); } public void Render(SpriteBatch batch) { batch.Draw(Choosescreen, new Rectangle(0, 0, 1280, 720), Color.White); } } public class Maingame : IState { Texture2D Spielbildschirm, axe; Vector2 position = new Vector2(100,100); private Game1 game1; public Maingame(Game1 game) { game1 = game; } public void Load(ContentManager content) { Spielbildschirm = content.Load<Texture2D>("hauszombie"); axe = content.Load<Texture2D>("axxx"); } public void Update(GameTime gametime) { KeyboardState keyboardState = Keyboard.GetState(); float delta = (float)gametime.ElapsedGameTime.TotalSeconds; position.X += 5 * delta; position.Y += 3 * delta; if (keyboardState.IsKeyDown(Keys.Escape)) game1.ChangeGameState(Game1.GameStates.IngamemenuState); } public void Render(SpriteBatch batch) { batch.Draw(Spielbildschirm, new Rectangle(0, 0, 1280, 720), Color.White); batch.Draw(axe, position, Color.White); } } public class Ingamemenu : IState { Texture2D Quitscreen; private Game1 game1; public Ingamemenu(Game1 game) { game1 = game; } public void Load(ContentManager content) { Quitscreen = content.Load<Texture2D>("quit"); } public void Update(GameTime gametime) { KeyboardState kbState = Keyboard.GetState(); if (kbState.IsKeyDown(Keys.Y)) game1.ChangeGameState(Game1.GameStates.MenuState); if (kbState.IsKeyDown(Keys.N)) game1.ChangeCurrentToLastGameState(); } public void Render(SpriteBatch batch) { batch.Draw(Quitscreen, new Rectangle(200, 200, 200, 200), Color.White); } }

    Read the article

  • lwjgl isKeyDown canceling out other keys

    - by AKrush95
    While trying to create a simple game where a square is manipulated via the keyboard keys, I have come across a small, rather irritating problem. I would like it to work so that when the opposite directional key is pressed, the character will stop; the character may move the other two directions while stopped in this situation. This works perfectly with LEFT and RIGHT held down; the player may move UP or DOWN. If UP and DOWN are held down, however, the player will not move, nor will Java recognize that the LEFT or RIGHT keys were pressed. import java.util.ArrayList; import java.util.Random; import org.lwjgl.*; import org.lwjgl.input.Keyboard; import org.lwjgl.opengl.*; import static org.lwjgl.opengl.GL11.*; public class Main { private Man p; private ArrayList<Integer> keysDown, keysUp; public Main() { try { Display.setDisplayMode(new DisplayMode(640, 480)); Display.setTitle("LWJGLHelloWorld"); Display.create(); } catch (LWJGLException e) { e.printStackTrace(); } p = new Man(0, 0); keysDown = new ArrayList<>(); keysUp = new ArrayList<>(); glMatrixMode(GL_PROJECTION); glLoadIdentity(); glOrtho(0, 640, 480, 0, 1, -1); glMatrixMode(GL_MODELVIEW); while (!Display.isCloseRequested()) { glClear(GL_COLOR_BUFFER_BIT); checkKeys(); p.draw(); Display.update(); Display.sync(60); } Display.destroy(); } public void checkKeys() { ArrayList<Integer> keys = new ArrayList<>(); keys.add(Keyboard.KEY_A); keys.add(Keyboard.KEY_D); keys.add(Keyboard.KEY_W); keys.add(Keyboard.KEY_S); for (int key : keys) { if (Keyboard.isKeyDown(key)) keysDown.add(key); else keysUp.add(key); } keysDown.removeAll(keysUp); keysUp = new ArrayList<>(); int speed = 4; int dx = 0; int dy = 0; if (keysDown.contains(keys.get(2))) { System.out.println("keyUP"); dy -= speed; } if (keysDown.contains(keys.get(3))) { System.out.println("keyDOWN"); dy += speed; } if (keysDown.contains(keys.get(0))) { System.out.println("keyLEFT"); dx -= speed; } if (keysDown.contains(keys.get(1))) { System.out.println("keyRIGHT"); dx += speed; } //if (keysDown.contains(keys.get(0)) && keysDown.contains(keys.get(1))) dx = 0; //if (keysDown.contains(keys.get(2)) && keysDown.contains(keys.get(3))) dy = 0; p.update(dx, dy); } public static void main(String[] args) { new Main(); } class Man { public int x, y, w, h; public float cR, cG, cB; public Man(int x, int y) { this.x = x; this.y = y; w = 50; h = 50; Random rand = new Random(); cR = rand.nextFloat(); cG = rand.nextFloat(); cB = rand.nextFloat(); } public void draw() { glColor3f(cR, cG, cB); glRecti(x, y, x+w, y+h); } public void update(int dx, int dy) { x += dx; y += dy; } } } That is the code that I am working with. In addition, I am unsure how to compile an executable jar that is using the lwjgl library in addition to slick-util.

    Read the article

  • Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

    - by Lucas
    I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

    Read the article

  • Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

    - by zewone
    I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686 ![Schizophrenic Ubuntu](http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) Any help much appreciated... Thanks, Philippe

    Read the article

  • How do I get to work my Atheros AR9485 Wireless card in Ubuntu 14.04 LTS?

    - by Ivan Kreimer
    I've recently installed Ubuntu 14.04 LTS in my ASUS D550CA, and so far things have gone great. The only problem I've got is the Wi-Fi. It doesn't work. I've got an Qualcomm Atheros AR9485. I've tried installing the drivers, but the sytem says it doesn't find any. So I started looking around this forum for solutions. I've read every single post from this forum about my Wi-Fi network adapter, and I've found nothing that solves my problem. Let me give you some info about my configuration. Disclaimer: my configuration is in spanish, so if you don't understand something you can either use Google translate, or use your imagination. :D When I run $ sudo lshw -C network this is what I get: *-network DEACTIVATED descripción: Interfaz inalámbrica producto: AR9485 Wireless Network Adapter fabricante: Qualcomm Atheros id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: wlan0 versión: 01 serie: 28:e3:47:5c:5d:3f anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.13.0-34-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:f7d00000-f7d7ffff memoria:f7d80000-f7d8ffff *-network descripción: Ethernet interface producto: RTL8101E/RTL8102E PCI Express Fast Ethernet controller fabricante: Realtek Semiconductor Co., Ltd. id físico: 0.2 información del bus: pci@0000:03:00.2 nombre lógico: eth0 versión: 06 serie: e0:3f:49:ce:57:49 tamaño: 100Mbit/s capacidad: 100Mbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8402-1_0.0.1 10/26/11 ip=181.165.245.39 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s recursos: irq:41 ioport:e000(size=256) memoria:f0004000-f0004fff memoria:f0000000-f0003fff At the beginning, you'll see that it says "*-network DEACTIVATED" (or at least that's what I translated), is that something bad? Then, when I run ipconfig this is what I get: eth0 Link encap:Ethernet direcciónHW e0:3f:49:ce:57:49 Direc. inet:181.165.245.39 Difus.:181.165.245.255 Másc:255.255.255.0 Dirección inet6: fe80::e23f:49ff:fece:5749/64 Alcance:Enlace ACTIVO DIFUSIÓN FUNCIONANDO MULTICAST MTU:1500 Métrica:1 Paquetes RX:221199 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:62025 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:124409589 (124.4 MB) TX bytes:7471899 (7.4 MB) lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158 (397.1 KB) When I put iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Finally, when I put sudo rfkill list all, I got: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no I hope anyone can help me solve this, I've searched a lot and found no solution. Thanks a lot.

    Read the article

  • Need help with chronic slow wifi connections

    - by mgeorge
    I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

    Read the article

  • Upgraded to 12.04 now wifi doesn't work

    - by Benito Kestelman
    My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

    Read the article

  • ubuntu 10.04: wlan0 No such device

    - by AodhanOL
    I am using a Dell xps l702x and I am using ubuntu 10.04 because I need to use f77 (don't ask) and I wasn't able to get it working on later versions of ubuntu. I cannot use the wifi at all. I have tried to fix it and have had limited success (changed the output from rfkill list all from Hard blocked: yes, to hard blocked: no). Here is the output from rfkill list all aodhan@aodhan-laptop:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-bluetooth: Bluetooth Soft blocked: no Hard blocked: no Here is the output from iwconfig: aodhan@aodhan-laptop:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. pan0 no wireless extensions. And here is the output from ifconfig -a: aodhan@aodhan-laptop:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 5c:f9:dd:3d:f2:f7 inet addr:192.168.1.17 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::5ef9:ddff:fe3d:f2f7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3417 errors:0 dropped:0 overruns:0 frame:0 TX packets:2894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3317567 (3.3 MB) TX bytes:505049 (505.0 KB) Interrupt:30 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 7e:7e:e8:39:70:af BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And finally, the output from lspci: 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1246 (rev a1) 03:00.0 Network controller: Intel Corporation Device 008a (rev 34) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Please help me! Thank you in advance. Edit: Further info - this is a dual install with a windows 7 system as the other option. However, I can't access that until tomorrow (I won't have access to the windows 7 disc until then, and grub isn't letting me load it). Therefore, I can't be sure whether it still works on that or not. It used to, though.

    Read the article

  • Copy and Paste without needing to use the Mouse

    - by Paul Farry
    In previous versions of windows when your were Copying Files (Ctrl-C) then alt-Tab (to the appropriate window) and Pasting (Ctrl-V) using the Keyboard everything could be driven by the keyboard. With Vista and 7, it seems if you are copying and pasting (and the files exist) in the Destination Location you have to Click the Copy and Replace, there doesn't seem to be a way to do it... "Do this for the next {n} Conflicts" can be driven by Alt-D, but the "Copy and Replace" and "Don't Copy" are not. Or is there and have I just missed something? I'm more than happy to change registry or something to enable Keyboard shortcuts for this.

    Read the article

  • Map Caps-Lock to Control in Windows 8.1

    - by Eric Huang
    Before the Windows 8.1 update, I was able to map Caps-Lock to Controls through the type of registry tweak in this post: Remapping a keyboard key in windows 8.1 However, after updating to 8.1, my tweak no longer works. What I had done was Windows Registry Editor Version 5.00 [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Keyboard Layout] "Scancode Map"=hex:00,00,00,00,00,00,00,00,02,00,00,00,1d,00,3a,00,00,00,00,00 Windows 8.1 may have changed how it interprets the keyboard layout registry, I'm guessing. I'm an avid emacs user, so this problem is a life-or-death scenario for me.

    Read the article

  • How to "restart/repair" an USB port?

    - by Click Ok
    My laptop has two USB ports, but one is broken, so I use a USB hub in the other good USB port. In that USB hub, I use a mouse and keyboard. Suddenly, that USB port doesn't detect the mouse and the keyboard (even with the light of the hub is on), and the only solution that I found is restarting the laptop. But just some minutes and the keyboard and mouse goes undetected again... Is there some method, software, etc. to "restart/repair" the USB port without restarting the PC?

    Read the article

  • How to assign hotkeys in OSX-snow-leopard

    - by 2816
    I am trying to assign a hotkey to open a folder in snow leopard. For example, in windows i could simply press the Windows+E to open the My Computer folder (or manually assign whatever folder i wanted to open). Is there a way to get this same behavior in OSX? I want to be able to launch applications, and open folder with my own keyboard mappings. For launching applications I use automator, create a service that receives no input to 'launch application' (from the utilities library). Then i can assign a keyboard shortcut to this service. Now i can launch applications with keyboard shortcuts. I still dont know how to open a folder. I know this can be done using quicksilver - but am looking for an organic approach that does not require any additional installs.

    Read the article

  • SSH onto Ubuntu box using RSA keys

    - by jex
    I recently installed OpenSSH on one of my Ubuntu machines and I've been running into problems getting it to use RSA keys. I've generated the RSA key on the client (ssh-keygen), and appended the public key generated to both the /home/jex/.ssh/authorized_keys and /etc/ssh/authorized_keys files on the server. However, when I try to login (ssh -o PreferredAuthorizations=publickey jex@host -v [which forces the use of public key for login]) I get the following output: debug1: Host 'pentheon.local' is known and matches the RSA host key. debug1: Found key in /home/jex/.ssh/known_hosts:2 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received Banner message debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: /home/jex/.ssh/id_rsa debug1: Authentications that can continue: publickey,keyboard-interactive debug1: Trying private key: /home/jex/.ssh/identity debug1: Trying private key: /home/jex/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey,keyboard-interactive). I'm not entirely sure where I've gone wrong. I am willing to post my /etc/ssh/sshd_config if needed.

    Read the article

  • Using a KVM with a Sun Ultra 45

    - by Kit Peters
    I have a friend with two machines: a Mac and a Sun Ultra45. He wants to use a single monitor (connected via DVI) and USB keyboard / mouse with both machines. Try as I might, the Sun box will not bring up a console if the KVM is connected. However, if I connect a monitor, keyboard, and mouse directly to the Sun box, it will bring up a console that I can then (IIRC) connect to the KVM. Is there any way I can make the Sun box always bring up a console, regardless of whether it "sees" a monitor, keyboard, and mouse?

    Read the article

  • Java OO design confusion: how to handle actions modified by states modified by actions...

    - by Arvanem
    Hi folks, Given an entity, whose action is potentially modified by states (of the entity and other entities) in turn potentially modified by other actions (of the entity and other entities) , what is the best way to code or design to handle the potential existence of the modifiers? Speaking metaphorically, I am coding a Java application representing a piano. As you know a piano has keys (which, when pressed, emit sound) and pedals (which, when pressed, modify the keys' sounds). My base class structure is as follows: Entity (for keys and pedals) State (this holds each entity's states, e.g. name such as "soft pedal", and boolean "Pressed"), Action (this holds each entity's actions, e.g. play sound when pressed, or modify others sounds). By composition, the Entity class has a copy of each of State and Action inside it. e.g.: public class Entity { State entityState = new State(); Action entityAction = new Action(); Thus I have coded a "C-Sharp" key Entity. When I "press" that entity (set its "Pressed" state to true), its action plays a "C-Sharp" sound and then sets its "Pressed" state to false. At the same time, if the "C-Sharp" key entity is not "tuned", its sound deviates from "C-Sharp". Meanwhile I have coded a "soft pedal" Entity. When that entity is "pressed", no sound plays but its action is to make softer the sound of the "C-Sharp" and other key entities. I have also coded a "sustain pedal" Entity. When that entity is "pressed", no sound plays but its action is to enable reverberation of the sound of the "C-Sharp" and other key entities. Both the "soft" and "sustain pedals" can be pressed at the same time with the result that keys entities become both softened and reverberating. In short, I do not understand how to make this simultaneous series of states and actions modify each other in a sensible OO way. I am wary of coding a massive series of "if" statements or "switches". Thanks in advance for any help or links you can offer.

    Read the article

  • Search Form in Responsive Design - Remove Search button on Mobile

    - by Kevin
    I'm working with a search box in the header of a responsive website. On desktop/tablet widths, there's a search input field and a styled 'search' button to the right. You can type in a search term and either click 'SEARCH' button or just hit enter on the keyboard with the same result. When you scale down to mobile widths, the search input field fills the width of the screen. The submit button falls below it. On a desktop, clicking the button or hitting enter activate the search. On an actual iphone phone, you can hit the 'SEARCH' button, but the native mobile keyboard that rises from the bottom of the screen has a search button where the enter/return key would normally be. It seems to know I'm in a form and the keyboard automatically gives me the option to kick off the search by basically hitting the ENTER key location....but it says SEARCH. So far so good. I figure I don't need the button in the header on mobile since it's already in the keyboard. Therefore, I'll hide the button on mobile widths and everything will be tighter and look better. So I added this to my CSS to hide it in mobile: #search-button {display: none;} But now the search doesn't work at all. On mobile, I don't get the option in the keyboard that showed up before and if I just hit enter, it doesn't work at all. On desktop at mobile width, hitting enter also not longer works. So clearly by hiding the submit/search button, the phone no longer gave me the native option to run the search. In addition, on the desktop at mobile width, even hitting enter inside the search input box also fails to launch the the search. Here's my search box: <form id="search-form" method="get" accept-charset="UTF-8, utf-8" action="search.php"> <fieldset> <div id="search-wrapper"> <label id="search-label" for="search">Item:</label> <input id="search" class="placeholder-color" name="item" type="text" placeholder="Item Number or Description" /> <button id="search-button" title="Go" type="submit"><span class="search-icon"></span></button> </div> </fieldset> </form> Here's what my CSS looks like: #search-wrapper { float: left; display: inline-block; position: relative; white-space: nowrap; } #search-button { display: inline-block; cursor: pointer; vertical-align: top; height: 30px; width: 40px; } @media only screen and (max-width: 639px) { #search-wrapper { display: block; margin-bottom: 7px; } #search-button { /* this didn't work....it hid the button but the search failed to load */ display: none;*/ } } So.....how can I hide this submit button when I'm on a mobile screen, but still let the search run from the mobile keyboard or just run by hitting enter when in the search input box. I was sure that putting display:none on the search button at mobile width would do the trick, but apparently not. Thanks...

    Read the article

< Previous Page | 92 93 94 95 96 97 98 99 100 101 102 103  | Next Page >